betaFeedback

WorksPhysics and Astronomy

Maser Threshold Characterization by Resonator Q-Factor Tuning

Abstract

Whereas the laser is nowadays an ubiquitous technology, applications for its microwave analogue, the maser, remain highly specialized, despite the excellent low-noise microwave amplification properties. The widespread application of masers is typically limited by the need of cryogenic temperatures. The recent realization of a continuous-wave room-temperature maser, using NV−^- centers in diamond, is a first step towards establishing the maser as a potential platform for microwave research and development, yet its design is far from optimal. Here, we design and construct an optimized setup able to characterize the operating space of a maser using NV−^- centers. We focus on the interplay of two key parameters for emission of microwave photons: the quality factor of the microwave resonator and the degree of spin level-inversion. We characterize the performance of the maser as a function of these two parameters, identifying the parameter space of operation and highlighting the requirements for maximal continuous microwave emission.

Introduction

The first maser system was realized using ammonia molecules in the gas phase[1] and applications for signal amplifiers, frequency standards or as spectrometers were subsequently proposed. However, the need for cryogenic and/or high vacuum environments restricted miniaturization and integration towards more general applications. Maser research and development was mainly focused on low-noise microwave receiving systems for deep-space antenna networks[2] and several other maser systems based on ruby[3], atomic hydrogen[4] or Rydberg atoms[5] were realized. These systems were all still subject to the same restrictions and the focus on fundamental research into masers declined. The field was reinvigorated upon the realization of a room-temperature pulsed maser in an optically pumped crystal of pentacene-doped pp-terphenyl, placed inside a high quality factor microwave resonator[6, 7, 8]. Here, masing was achieved not only

without the need of cryogenics or a high-vacuum environment, but also with easily accessible optical pump rates. Shortly afterwards, a proposal for a continuous-wave room-temperature maser in optically spin polarized, negatively charged nitrogen vacancy (NV−^{-}) centers in diamond[9] and its consecutive experimental realization[10] followed. The excellent low-noise amplification properties of the maser have been demonstrated in recent work[11, 12, 13] and has found application in enhanced quantum sensing of molecular spin ensembles[14].

Image not extracted

Figure 1. Schematic cross-section of the microwave cavity-resonator setup. A microwave cavity, housing the sapphire ring resonator. The schematic shows half of the cavity to reveal the interior. The light blue sapphire ring is held by two Teflon holders. On the top is the iris coupled waveguide port. The coupling to the resonator is adjusted by a Teflon screw with a metal ring at its tip. The 532nm optical pump laser is aligned along the symmetry axis of the cylindrical resonator, while the static magnetic field B0B_0 is perpendicular to it. Finally, the diamond sample is placed inside the resonator. b Loaded QQ-factor as a function of the resonator coupling, showing the full range of coupling, with the diamond sample in the resonator.

The search for other solid-state maser materials, such as SiC[15] has continued, and an application in quantum technology by creating a maser system based on Floquet states in Xe atoms[16] has also been reported.

With the increased focus on room-temperature solid-state masers a quantitative experimental characterization of the parameter space of operation supplements the current endeavours to optimize the performance of such systems. Understanding the behaviour of the maser performance, defined by the level-inversion of the spin ensemble and the loaded QQ-factor QLQ_\mathrm{L} of the resonator, can lead to higher output power maser systems. To guarantee reproducibility and maximise the power output of maser-based technologies, a complete understanding of the system parameter space, including the minimal requirements to surpass the masing threshold, is required.

Here, we present an experimental setup that we exploited to investigate the maser performance of a NV−\mathrm{NV}^{-} spin ensemble hosted in diamond as a function of the resonator quality factor and the degree of spin level-inversion. In the resulting maser threshold diagram, we can clearly identify the threshold for maser action, thereby obtaining a set of experimental boundary conditions for the optimal operation of a maser system. Additionally, our optimized setup yields the highest continuous-wave maser output power reported to date.

Results and Discussion

Experimental setup: We use a cylindrical dielectric ring resonator made of sapphire to deliver/detect resonant microwaves to/from the NV−\mathrm{NV}^{-} centers contained in the diamond host. A key parameter for the continuous maser emission is the loaded QQ-factor, QLQ_\mathrm{L}, of the resonator, which is defined by

1QL=1Qint+1Qext\frac{1}{Q_\mathrm{L}} = \frac{1}{Q_\mathrm{int}} + \frac{1}{Q_\mathrm{ext}}

with the internal QQ-factor, QintQ_\mathrm{int}, and the external QQ-factor, QextQ_\mathrm{ext}. Although sapphire dielectric resonators exhibit low dielectric losses[17], radiative losses typically dominate and prevent high internal quality factors. Hence, to suppress radiative losses the resonator is placed inside a metal cavity. The cavity design is further constrained by two conditions: (i) it has to fit between the poles of our electromagnet system, which gives the static magnetic field B0B_0 used to tune the energy levels of the NV−\mathrm{NV}^{-} spins via the Zeeman interaction, and (ii) the resonance frequency of the cavity containing the sapphire ring is required to be within the 9–10 GHz (X-band) frequency range, to allow a fast pre-characterization of the NV−\mathrm{NV}^{-} spin ensemble by conventional electron spin resonance (ESR). To this end, we designed a cylindrical cavity made of oxygen-free high-thermal conductivity (OFHC) copper, plated with thin layers of (first) silver and (second) gold to prevent oxidation of the metal surfaces, thereby minimising additional resistive losses.

Figure 1(a) shows a 3D schematic of the fully assembled cavity cut at a symmetry plane to reveal the interior. The cavity has sample entries at opposite ends of the cylinder symmetry axis for sample and optical access. In the center of the cavity the resonator is held in place by two wire-frame Teflon holders. The holders are machined to have minimal volume in order to minimize additional dielectric losses. Microwave power is coupled in and out via a single waveguide iris port on the top. This port represents the external quality factor QextQ_\mathrm{ext} and together with QintQ_\mathrm{int} the resonator coupling k=Qint/Qextk = Q_\mathrm{int}/Q_\mathrm{ext} is defined. kk is controlled via a Teflon screw with a metal ring at its tip. Changing the coverage of the iris by the metal ring allows a continuous change[18] from over-coupled to under-coupled: the regimes where QLQ_\mathrm{L} is dominated by external losses or intrinsic losses, respectively. Figure 1(b) shows the achievable QLQ_\mathrm{L} as a function of kk for our resonator-cavity system, loaded with the diamond sample. The resonator parameters are extracted from microwave reflection measurements, using a vector network analyzer. By fitting the microwave reflection as a function of frequency with a Lorentzian model function the parameters for resonance frequency, resonator coupling and internal quality factor are determined. A description of the model function can be found in the methods section. We use the TE01δ\mathrm{TE}_{01\delta} mode for our experiments, where the electric field is mostly contained in the sapphire ring and the magnetic field is mostly focused in the bore. Without a sample, the sapphire resonator has a resonance frequency ωres/2π=9.25 GHz\omega_\mathrm{res}/2\pi= 9.25\,\mathrm{GHz} and the QL=42,500Q_\mathrm{L} = 42{,}500 when fully under-coupled. We define the resonator as fully under-coupled when k=0.0027k = 0.0027, where the Iris is no longer covered by the metal tip of the Teflon screw. Here, QLQ_\mathrm{L} remains unchanged upon further extraction of the screw. For detailed cavity and resonator dimensions see Supplementary Note 4[19].

Maser working principles: The process of continuous emission of microwave photons from the NV−^{-} centers is schematically shown in Figure 2 (a) to (Figure 2c). The diamond hosting the NV−^{-} centers is placed inside a high-QQ resonator, which is highly under-coupled (k≪1k \ll1). The resonator may be pictured in analogue to its optical counterpart the laser, with one perfectly reflective mirror and one weakly transmitting mirror. The latter represents the iris coupled single microwave port on the microwave cavity.

Image not extracted

Figure 2. Schematic of the maser emission process. a - c The blue mirrors are the optical analogue of a high-QQ microwave resonator, with one mirror being fully reflective (dark blue) and one weakly transmissive (light blue); a Energy states of the NV−\mathrm{NV}^{-} spin ensemble aligned along B0B_0. The ∣−1⟩\lvert-1\rangle state is tuned below the ∣0⟩\lvert0\rangle state by the Zeeman interaction, while the optical pump generates a population inversion and spins spontaneously emit microwaves. b Spontaneously emitted or thermally stimulated microwaves can stimulate the emission of additional microwaves. c For sufficiently large optical pump rates and a high QLQ_\mathrm{L} coherent microwave emission is established.

The applied static magnetic field B0B_0 lifts the degeneracy of the ∣±1⟩\lvert\pm1\rangle states and, tunes the ∣−1⟩\lvert-1\rangle state energetically below the ∣0⟩\lvert0\rangle state such that the splitting ℏωM\hbar\omega_{\mathrm{M}} is resonant with the microwave resonator frequency. The experiment is performed only on one sub-set of NV−^{-} centers which are aligned with the external magnetic field B0B_0. This provides the shown level structure, having the largest Zeeman splitting of the energy levels and consequently the largest initial population difference at Boltzmann equilibrium. By illuminating the NV−^{-} centers continuously with a 532 nm laser, the spin populations which are initially at Boltzmann equilibrium are predominately pumped into the ∣0⟩\lvert0\rangle state[20], resulting in a level-inversion (see Figure 2 (a)). A description of the optical spin polarization process is found in Supplementary Note 2[19]. Finally, the laser polarization is required to be aligned along the NV−^{-} defect axis to achieve most efficient pump rates[21, 22].

To trigger a collective stimulated emission, an initial photon with ℏωM\hbar\omega_{\mathrm{M}} is required. This is provided either by an externally applied seeding photon, due to spontaneous emission or thermal photons (see Figure 2 (b)). From this point an avalanche of stimulated photons is created, forming a coherent microwave field inside the resonator (see Figure 2 (c)). If the laser pump rate is sufficient to maintain the level inversion and the resonator loaded quality factor is high enough to support a large enough coherent microwave field, continuous microwave emission is achieved.

Image not extracted

Figure 3. Maser emission spectrum. a Maser emission power ∣AM∣\lvert A_{\mathrm{M}}\rvert, in logarithmic units, as a function of frequency and static magnetic field at wL=430 s−1w_{\mathrm{L}} = 430\,\mathrm{s}^{-1} and QLQ_{\mathrm{L}} of about 33,500. b ∣AM∣\lvert A_{\mathrm{M}}\rvert as a function of frequency for two different magnetic field values, indicated by the red and green dashed lines in a.

NV defect axis alignment: In our experimental setup, the diamond sample is held inside a quartz ESR tube, supported between two additional quartz tubes fitted inside the first one. The tube is inserted into the cavity and positioned such that the diamond is located at the center of the sapphire ring where the magnetic component of the microwave field is largest. The cavity with sample is mounted between the poles of a electromagnet system. We connect either a conventional ESR spectrometer, a vector network analyzer or a spectrum analyzer to the microwave port of the cavity, to perform low-power microwave spectroscopy of the NV−^{-} spin transitions or to study the maser emission. A goniometer is attached to the sample tube, allowing a precise rotation of the quartz tube containing the diamond with respect to the static magnetic field. Conventional ESR as a function of B0B_0 and rotation angle is performed to find an orientation of the diamond where the defect axis of a sub-set of NV−^{-} centers is mostly parallel to the applied magnetic field. For such an orientation the NV−^{-} spins feature an energy level scheme of the electronic ground state as schematically shown in Figure 2 (a) and the states ∣0⟩\lvert0\rangle and ∣±1⟩\lvert\pm1\rangle can be considered pure. This can be characterized by the frequency/magnetic field splitting between the low-field (∣0⟩↦∣+1⟩\lvert0\rangle\mapsto\lvert+1\rangle) and high-field (∣0⟩↦∣−1⟩\lvert0\rangle\mapsto\lvert-1\rangle) transitions corresponding to twice the zero-field splitting DD. Away from this alignment the states become mixed, resulting in a smaller splitting than 2D2D between the two allowed transitions[23, 24] and a smaller maximal achievable spin polarization. Without laser illumination, we find a maximal splitting of about 205 mT or 5.762 GHz, agreeing well with twice the zero-field splitting, DD, of NV−^{-} centers in diamond.

Maser emission spectrum characterization: Having optimized the orientation of the NV−^{-} centers, we characterize the performance of our maser setup by analyzing the microwave emission spectrum. Figure 3 (a) shows the color encoded maser emission power ∣AM∣\lvert A_{\mathrm{M}}\rvert as a function of frequency and static magnetic field for a laser pump rate wL=430 s−1w_{\mathrm{L}} = 430\,\mathrm{s}^{-1} and with the resonator fully under-coupled, QL≈QintQ_{\mathrm{L}} \approx Q_{\mathrm{int}}, which gives a loaded quality factor QLQ_{\mathrm{L}} of 33,500. The three bright lines represent the maser emission of the three 14N{}^{14}\mathrm{N} hyperfine transitions of the NV−^{-} centers oriented along B0B_0. In this configuration, we achieve a maximum maser emission power of −56.5-56.5 dBm. The maser emission shows a finite frequency-magnetic field dispersion, where the maser power is maximal in the center of the line. This is illustrated in Fig. 3 (b) which depicts the maser emission power as a function of frequency for two fixed magnetic fields. The dispersion results from the hybridization of the microwave resonator mode and the resonant NV−^{-} transition. The resonator resonance frequency ωres/2π=9.12 GHz\omega_{\mathrm{res}}/2\pi= 9.12\,\mathrm{GHz} lies at the center of the middle maser emission line. The inverted spin population causes a dispersive shift of the resonator frequency to lower frequencies for the lower magnetic field emission line and respectively to a shift to higher frequencies for the higher magnetic field emission line. The maser dispersion can be described via a Tavis-Cummings model with an inverted spin polarization, where the frequency range covered by the maser emission lines increases with increasing inversion.

In order to determine the dependency of the maser output on the laser pump rate wLw_{\mathrm{L}} and the loaded quality factor QLQ_{\mathrm{L}}, both were varied systematically. The latter is dependent on the resonator coupling kk which is controlled by the iris screw. Figure 4 (a) shows the peak maser power ∣AM∣\lvert A_{\mathrm{M}}\rvert of the central maser line as a function of wLw_{\mathrm{L}} (from 165 s−1165\,\mathrm{s}^{-1} to 695 s−1695\,\mathrm{s}^{-1}) and QLQ_{\mathrm{L}} (from 14,000 to 33,500). Note, that after each change of wLw_{\mathrm{L}} we wait 45 min before starting measurements to allow the diamond to reach a thermal equilibrium (see Supplementary Note 1 for details[19]). For low loaded quality factors, i.e. an over-coupled resonator, there is no microwave emission for all laser pump rates studied and the signal amplitude is represented by the noise floor of the spectrum analyzer. Note that critical resonator coupling (k=1k = 1) is achieved at QL≈20,000Q_{\mathrm{L}} \approx20,000, marking the transition between over- and under-coupling[25]. With increasing QLQ_{\mathrm{L}} a weak microwave emission is observed for moderate to high laser pump rates. Here, the emission spectrum is broad and governed by the amplification of thermal photons residing in the resonator[9]. In this region, the resonator losses are still too high to allow the build-up of sufficient stimulated photons for continuous masing. For QL>26,000Q_{\mathrm{L}} > 26,000 and wL>400 s−1w_{\mathrm{L}} > 400\,\mathrm{s}^{-1} the rate of stimulated emission exceeds the losses in the resonator and the spin system, and continuous masing is established. Figure 4 (b) shows the evolution of the peak maser power as a function of the loaded quality factor for two different laser pump rates. Upon passing the threshold QLQ_{\mathrm{L}} of 26,000, ∣AM∣\lvert A_{\mathrm{M}}\rvert increases until reaching an onset of saturation for the highest QLQ_{\mathrm{L}}, where the final level of saturation depends on the laser pump rate.

Image not extracted

Figure 4. Maser threshold diagram. a Maximal maser emission power ∣AM∣\lvert A_{\mathrm{M}}\rvert, in logarithmic units, of the central hyperfine maser transition line as a function of laser pump rate wLw_{\mathrm{L}} and the loaded quality factor QLQ_{\mathrm{L}} of the resonator. The white and grey dashed lines represent the theoretical threshold for masing, with and without temperature effects, respectively. b ∣AM∣\lvert A_{\mathrm{M}}\rvert as a function of QLQ_{\mathrm{L}} for two wLw_{\mathrm{L}}, indicated by the purple and red dashed lines in a. c ∣AM∣\lvert A_{\mathrm{M}}\rvert as a function of wLw_{\mathrm{L}} at two QLQ_{\mathrm{L}}, indicated by the blue and green dashed lines in a.

A QLQ_{\mathrm{L}} larger than 26,000 further promotes the stimulated microwave emission, thus reducing the threshold laser pump rate required. For a fully under-coupled resonator with QL=33,500Q_{\mathrm{L}} = 33,500, continuous microwave emission is already achieved for wL>200 s−1w_{\mathrm{L}} > 200\,\mathrm{s}^{-1}. Figure 4 (c) shows the peak maser power ∣AM∣\lvert A_{\mathrm{M}}\rvert as a function of the laser pump rate wLw_{\mathrm{L}} at two different loaded quality factors of the resonator. The peak maser power increases with increasing laser pumping, reflecting the achieved level-inversion. Consequently, for the largest QLQ_{\mathrm{L}} and highest wLw_{\mathrm{L}}, which guarantees a stable microwave field inside the resonator and the largest level inversion, respectively, the highest maser power of −54.1-54.1 dBm is achieved. This is an improvement of more than three orders of magnitude in maser power over the initial report on a NV−^{-}-based maser in Ref. 10 with reported −90.3-90.3 dBm. The threshold laser pump rate wthw_{\mathrm{th}} for masing can be derived from the steady-state Heisberg equations of motion based on the coupled resonator-spin ensemble Tavis-Cummings model, including dissipative channels for the resonator and spins, and is given by[9, 10, 26].

wth=ηT1(g02Nκ0γ−1).(1)w_{\mathrm{th}} = \frac{\eta}{T_1\left(\frac{g_0^2N}{\kappa_0\gamma}-1\right)}. \tag*{(1)}

Here, T1T_1 is the effective longitudinal relaxation time of the NV−^{-} spins, g0g_0 gives the strength of the magnetic dipole coupling between a single spin and a single microwave photon[27], NN is the absolute number of spins per hyperfine transition and per NV−^{-} defect axis and κ0\kappa_0 and γ\gamma are the resonator and spin loss rates (HWHM), respectively. We estimate g0/2πg_0/2\pi by finite element simulations of the magnetic field profile inside the sapphire ring resonator[28] to an average value of 0.244 Hz and determine γ/2π\gamma/2\pi and NN via low-power microwave spectroscopy of the low-field transition (∣0⟩↦∣+1⟩\lvert0\rangle\mapsto\lvert+1\rangle) to 530.8 kHz ±\pm 7.7 kHz and 2.32×10132.32 \times10^{13}, respectively. A detailed derivation of these system parameters is found in Supplementary Note 3[19]. The resonator loss rate is defined through QLQ_{\mathrm{L}} as κ0=ωres/2QL\kappa_0 = \omega_{\mathrm{res}}/2Q_{\mathrm{L}}, which we control by changing the resonator coupling. The scaling factor η\eta modifies the optical pump rate defined for a two-level system within the framework of the Tavis-Cummings model to take all seven energy levels involved in the pumping of a single NV−^{-} spin into account. We extract η=14.05\eta= 14.05 from the calculated spin-level inversion as a function of wLw_{\mathrm{L}}[9, 10], by solving the set of optical pump rate equations in the steady-state[29]. For T1T_1 we explicitly take the influence of an optical pump into account. In addition to polarizing spins, the pump leads to excessive heating of the diamond, which decreases the T1T_1 time[30]. We determine T1T_1 for each wLw_{\mathrm{L}}, finding 5.2 ms for low wLw_{\mathrm{L}} and a minimum of 1.5 ms for the highest wLw_{\mathrm{L}}, where a detailed description of the T1T_1 dependence on wLw_{\mathrm{L}} is given in Supplementary Note 1[19]. The white dashed line in Figure 4 (a) gives the masing threshold wthw_{\mathrm{th}} as a function of the loaded quality factor and is in excellent agreement with the experimentally found threshold of our maser, when acknowledging the reduction of the relaxation time due to high pump rates. For comparison, we include the expected threshold for a fixed T1=5.2 msT_1 = 5.2\,\mathrm{ms} (grey dashed line), demonstrating the significant influence of laser heating.

Conclusion

To summarize, our characterization setup allows the resonator coupling to be continuously and precisely adjusted between over- and under-coupled in conjunction with the optical pump rate. This permits the detailed study of the performance of the maser as a function of the rate of stimulated emission and the degree of level-inversion. Control of these parameters enabled the first experimental verification of the maser threshold equation over a wide parameter space. Thus, the regions of microwave emission below the detection limit, thermal photon amplification and continuous masing could be identified in a NV−^{-} diamond maser.

Our results highlight an efficient operation of the maser is in the highly under-coupled regime. Clearly, this limits the maser output power as only a small fraction of the microwaves in the weakly coupled resonator can exit. For applications, a higher output is essential and, hence, a larger coupling to the resonator is required. The resulting threshold diagram suggests that either higher pump rates or a resonator with a higher QintQ_{\mathrm{int}} will enable a larger coupling of the resonator. However, higher pump rates not only require bulky laser systems but cause the sample to heat up. We demonstrate that the T1T_1 relaxation time is shortened, thus reducing the spin inversion. Indeed, it is clear for our results that pump rates can be reduced to a level where small (e.g. <1 W<1\,\mathrm{W}) laser diodes can be employed instead. Therefore, increasing the QQ factor of the resonator is a more viable approach, although it is necessary to point out that this will decrease the bandwidth[11]. Finally, the optimized design yielded an increase of the maximal maser output of more than three orders of magnitude compared to the initial report on a NV−^{-}-based maser from −90.3 dBm-90.3\,\mathrm{dBm} to −54.1 dBm-54.1\,\mathrm{dBm}[10]. We attribute this mainly to an improved heat management of the diamond sample to limit a reduction in T1T_1 time and consequently limit the increase of the masing threshold. Thus it provides not only a blueprint for solid-state based maser systems and but also sets a benchmark for future characterization and optimization studies.

Methods

Diamond Sample: Our diamond sample is of rhombic shape with its long axis having about 5 mm5\,\mathrm{mm}, its short axis having about 4 mm4\,\mathrm{mm} and a thickness of 1 mm1\,\mathrm{mm}. The diamond consists of natural abundance carbon and we estimate the total number of NV−^{-} to 2.78×10142.78 \times10^{14} or 0.16 ppm0.16\,\mathrm{ppm} (see Supplementary Note 3 for details on the number of spins estimate[19]). At room temperature and no optical pump the NV−^{-} feature a T2=25 μsT_2 = 25\,\mathrm{\mu s}, determined by pulsed ESR.

Laser Pumping: We use a 532 nm532\,\mathrm{nm} Coherent Verdi V-5 laser to optically pump the spin population of the NV−^{-} centers. The laser features a spot size of about 4 mm4\,\mathrm{mm} and hits the diamond sample on its flat edge, an area of about 4 mm×1 mm4\,\mathrm{mm} \times1\,\mathrm{mm}. We determine the laser pump rate as wL=σPpump/Apumpℏωpumpw_L = \sigma P_{\mathrm{pump}}/A_{\mathrm{pump}}\hbar\omega_{\mathrm{pump}} (Ref. 10), with the one-photon absorption cross-section for NV−^{-} centers σ=3.1×10−21 m2\sigma= 3.1 \times10^{-21}\,\mathrm{m^2}, the pump laser power PpumpP_{\mathrm{pump}}, the laser spot area ApumpA_{\mathrm{pump}} and the laser frequency ωpump\omega_{\mathrm{pump}}.

Microwave Spectroscopy: We study the microwave emission from the maser with a Keysight N9020B MXA 10Hz to 44GHz spectrum analyzer. To improve the SNR we pre-amplify the maser signal, using a Mini Circuits Low Noise Amplifier ZX60-06183LN+ prior detection by the spectrum analyzer. The low power microwave spectroscopy was carried out using an Anritsu vector network analyzer MS46122B 1MHz to 43.5GHz. For conventional ESR measurements a Bruker EMXplus spectrometer is used.

Resonator Coupling: We determine the microwave resonator coupling kk by measuring the microwave reflection as a function of frequency with a VNA, far detuned from the NV−^{-} centers. We fit the magnitude of the reflection scattering parameter ∣S11∣\lvert S_{11}\rvert of the resonator for different positions of the Iris screw, using a Lorentzian model function derived from an equivalent circuit model, which depends on kk[31].

∣S11∣=A∣k−1−iQint(ωωres−ωresω)k+1+iQint(ωωres−ωresω)∣.(2)\lvert S_{11}\rvert= A \left\lvert\frac{k-1-\mathrm{i}Q_{\mathrm{int}}\left(\frac{\omega}{\omega_{\mathrm{res}}}-\frac{\omega_{\mathrm{res}}}{\omega}\right)}{k+1+\mathrm{i}Q_{\mathrm{int}}\left(\frac{\omega}{\omega_{\mathrm{res}}}-\frac{\omega_{\mathrm{res}}}{\omega}\right)} \right\rvert. \tag*{(2)}

In addition, we can extract the internal quality factor QintQ_{\mathrm{int}} and via the relation for the resonator coupling k=Qint/Qextk = Q_{\mathrm{int}}/Q_{\mathrm{ext}} the external Q-factor QextQ_{\mathrm{ext}} and hence the loaded quality factor QLQ_L, as well as the resonator frequency ωres\omega_{\mathrm{res}} and its loss rate κ0\kappa_0.

Data Availability

The data that supports the findings of this study is available upon reasonable request.

Author Contribution

S.R., R.R. and C.W.M.K. designed and optimized the resonator. The experimental setup and its automation was realized by S.R., Y.F., H.T.A.W., C.W.Z. and C.W.M.K.. C.W.Z. performed the experiments and the data analysis with input from J.D.B. and C.W.M.K.. C.W.Z. supported by C.W.M.K. wrote the manuscript with input from all authors. C.W.Z., J.D.B. and C.W.M.K. conceived the study.

Acknowledgment

This study is supported by EPSRC through EP/S000690/1 and EP/S000798/2 and the Royal Society through URF\R1\191297. We greatly acknowledge the work and expertise of the workshop personnel Stefanie Porger and Jens Wiegert at the University of Saarland for building the cavity and components for it.

Competing interests

The Authors declare no conflict of interests.

Temperature Increase of the Diamond due to Optical Pumping

The study of the maser output power as a function of optical pump rate requires considerable laser powers. The highest pump rate wL=695 s−1w_{\mathrm{L}} = 695\,\mathrm{s}^{-1} is achieved by a laser power of 1.05 W. Such high powers lead to excess heating of the diamond, which cannot be dissipated fully in our measurement setup. As described in the main text, the diamond sample is held inside a quartz ESR tube (5 mm outer diameter (OD)), supported between two additional quartz tubes (4 mm OD) fitted tightly inside the first one. Through the ESR tubes the diamond is indirectly thermally connected to the sapphire ring as well as the tube holders on the cavity body, which allows a finite thermal transport of the excess heating from the laser. In addition, we introduce a weak nitrogen gas flow into the cavity body to achieve an additional cooling effect. The nitrogen gas is connected to an inlet on the waveguide and flows via the Iris into the cavity and out via gaps in the ESR tube holders. Together, a finite thermal equilibrium in the diamond will establish after some time. For the experiments presented in the main text, we wait 45 minutes before a start of a measurement, after changing the laser power. The longitudinal relaxation time T1T_1 exhibits a strong temperature dependenceS30. For temperatures above room-temperature the relaxation rate 1/T11/T_1 predominately increases with T5T^5. As the maser threshold wthw_{\mathrm{th}} is indirect proportional to T1T_1 (see main text), the threshold will increase due to the effects of laser heating.

To determine the temperature increase in our maser characterization setup, we first determine the change of the zero-field splitting ΔD\Delta D as a function of optical pump rate, via low power microwave spectroscopy of the low- and high-field NV−^- spin transitions, and is shown in Supplementary Figure 1 (a). With increasing pump rate the zero-field splitting is decreasing. We define the room-temperature value of D=2.88 GHzD = 2.88\,\mathrm{GHz} as the reference for the relative shift ΔD\Delta D. Due to this temperature dependence, NV centers are highly sensitive thermometers. The temperature dependence can be described by a second order polynomial,

ΔD=ΔDcal+a1T+a2T2,(3)\Delta D = \Delta D_{\mathrm{cal}} + a_1 T + a_2 T^2, \tag*{(3)}

with coefficients a1=3.279×10−2 MHz K−1a_1 = 3.279 \times10^{-2}\,\mathrm{MHz\,K}^{-1} and a2=−1.787×10−4 MHz K−2a_2 = -1.787 \times10^{-4}\,\mathrm{MHz\,K}^{-2}. With the constant offset ΔDcal=5.9 MHz\Delta D_{\mathrm{cal}} = 5.9\,\mathrm{MHz} we calibrate the model to produce a zero shift at room-temperature. With the model function we can relate the measured ΔD\Delta D to a temperature, as shown in Supplementary Figure 1 (b).

Finally, we can find the corresponding T1,effT_{1,\mathrm{eff}} times for each optical pump rate used in the maser characterization. Supplementary Figure 1 (c) shows the calculated temperature dependence of T1T_1 (solid red line) together with the T1,effT_{1,\mathrm{eff}} for each pump rate used in the experiment (symbols), ranging from 165 s−1\mathrm{s}^{-1} to 695 s−1\mathrm{s}^{-1}. We calculate the relaxation time following the formalism presented in S30

T1=(A1+A2eΔ/kBT−1+A3T5)−1.(4)T_1 = \left(A_1 + \frac{A_2}{e^{\Delta/k_{\mathrm{B}}T}-1} + A_3T^5\right)^{-1}. \tag*{(4)}
Image not extracted

Figure 1 (PDF p. 7). Temperature dependence of zero-field splitting and relaxation time. a Color encoded microwave reflection ∣S11∣\lvert S_{11}\rvert as a function of VNA frequency and static magnetic field, at a pump rate of 695 s−1\mathrm{s}^{-1}. b Effective loss rate κeff\kappa_{\mathrm{eff}} of the resonator - spin ensemble hybrid system as a function of the static magnetic field. The orange solid line is a fit of Eq. (S4) to the data.

Image not extracted

Figure S2. Optical spin polarization scheme. Schematic of the electronic energy levels of a NV−^{-} spin ensemble. The triplet states 3A2^{3}\mathrm{A}_{2} and 3E^{3}\mathrm{E} are considered to be quantized along a principal axis of the zero-field splitting tensor. A continuous optical pump via a 532nm laser can achieve a majority population of the 3A2 ∣0⟩^{3}\mathrm{A}_{2}\ |0\rangle state, due to the spin selective intersystem crossing in the excited 3E^{3}\mathrm{E} triplet. The coefficients are A1=0.06 s−1A_{1}=0.06\ \mathrm{s}^{-1}, A2=2.1×103 s−1A_{2}=2.1\times10^{3}\ \mathrm{s}^{-1} and A3=2.2×10−11 s−1K−5A_{3}=2.2\times10^{-11}\ \mathrm{s}^{-1}\mathrm{K}^{-5}, Δ=1.17×10−20 J\Delta=1.17\times10^{-20}\ \mathrm{J} is the dominant local vibrational energy and kbk_{\mathrm{b}} is the Boltzmann constant.

Supplementary Note 2: Optical Spin Polarization of the NV- Spin Ensemble

Supplementary Figure 2 shows the schematic electronic energy level scheme for NV−^{-} spins at zero applied magnetic fieldS10,S20. We use a green 532nm laser to excite the population from the electronic ground state 3A2^{3}\mathrm{A}_{2} into the excited state 3E^{3}\mathrm{E}. Hereby, all of the spin triplet states ∣0⟩|0\rangle and ∣±1⟩|\pm1\rangle being pumped equally. The excited triplet state decays via a red fluorescence back in the 3A2^{3}\mathrm{A}_{2}. Additionally, the electrons from the excited ∣±1⟩|\pm1\rangle states undergo a spin selective intersystem crossing via the singlet states 1A^{1}\mathrm{A} and 1E^{1}\mathrm{E}. From there electrons decay into the 3A2^{3}\mathrm{A}_{2} triplet ground state with about equal rates. Due to the spin selective intersystem crossing in the excited state a stable majority population of the ∣0⟩|0\rangle can be achieved, under continuous laser pumping.

Supplementary Note 3: Microwave Spectroscopy of the NV- Spin Ensemble and Number of Spins Estimation

In addition to the microwave emission spectrum of the maser, we investigated the NV−^{-} spin transitions by low power microwave spectroscopy. In particular, we studied the low-field electron spin resonance (ESR) transition (∣0⟩↦∣+1⟩|0\rangle\mapsto|+1\rangle) as a function of microwave frequency and magnetic field B0B_{0} and recorded the microwave reflection S11S_{11} with a vector network analyzer (VNA). This transition is dominantly absorptive as the optically spin polarized ∣0⟩|0\rangle is energetically lying below the ∣+1⟩|+1\rangle state, corresponding to a positive population difference.

Supplementary Figure 3 (a) shows the magnitude of the microwave reflection ∣S11∣|S_{11}| as a function of VNA frequency and static magnetic field, with an optical pump rate of wL=695 s−1w_{\mathrm{L}}=695\ \mathrm{s}^{-1} applied to the spin ensemble. The horizontal purple line represents the microwave resonator. At the center of the field region the resonator is interrupted three times, where the resonator interacts with the NV−^{-} spin ensemble. The splitting in three lines is due to the hyperfine interaction with the spin 1 14N^{14}\mathrm{N} nuclei[14]. On resonance the resonator experiences a dispersive shift, indicating the onset of the strong coupling regime. We extract the collective coupling strength geffg_{\mathrm{eff}} between the resonator and the spin ensemble to estimate the number of spins contributing to the coupling. To this end, we fit the resonator microwave reflection for each magnetic field point, using a Lorentzian model function derived from an equivalent circuit modelS31.

∣S11∣=A∣k−1−iQint(ωωres−ωresω)k+1+iQint(ωωres−ωresω)∣.(5)|S_{11}|=A\left|\frac{k-1-\mathrm{i}Q_{\mathrm{int}}\left(\frac{\omega}{\omega_{\mathrm{res}}}-\frac{\omega_{\mathrm{res}}}{\omega}\right)}{k+1+\mathrm{i}Q_{\mathrm{int}}\left(\frac{\omega}{\omega_{\mathrm{res}}}-\frac{\omega_{\mathrm{res}}}{\omega}\right)}\right|. \tag*{(5)}

Far detuned from the spin ensemble, we can extract the internal quality factor QintQ_{\mathrm{int}} and via the relation for the resonator coupling k=Qint/Qextk=Q_{\mathrm{int}}/Q_{\mathrm{ext}} the external Q-factor QextQ_{\mathrm{ext}} and hence the loaded quality factor QLQ_{\mathrm{L}}, as well as the resonator frequency ωres\omega_{\mathrm{res}} and its loss rate κ0S31\kappa_0^{\mathrm{S31}}. Over the full magnetic field range the loss rate changes, represented by an effective loss rate κeff\kappa_{\mathrm{eff}} and shown in Supplementary Figure 3 (b). κeff\kappa_{\mathrm{eff}} shows three prominent peaks at the NV−^- resonances, where the increased loss rate results from the hybridization of the two systems, leading to an average between resonator and spin ensemble loss rates κ0\kappa_0 and γ\gamma, respectively. Using a coupled harmonic resonator model, κeff\kappa_{\mathrm{eff}} can be described using?

κeff=κ0+∑n=−1+1geff,n2γΔn2+γ2.(6)\kappa_{\mathrm{eff}}=\kappa_0+\sum_{n=-1}^{+1}\frac{g_{\mathrm{eff},n}^{2}\gamma}{\Delta_n^{2}+\gamma^{2}}. \tag*{(6)}

The sum is over all three hyperfine split ESR transitions with n=−1,0,+1n=-1,0,+1 and Δn=gNVμBℏ(B0−BESR,n)\Delta_n=\frac{g_{\mathrm{NV}}\mu_{\mathrm{B}}}{\hbar}(B_0-B_{\mathrm{ESR},n}) gives the detuning from the individual ESR resonances. We use the same spin loss rate for all transitions and find γ/2π=530.8 kHz±7.7 kHz\gamma/2\pi=530.8\,\mathrm{kHz}\pm7.7\,\mathrm{kHz}. The collective coupling strength is the strongest for the lowest field transition and weakest for the highest field transition, which we attribute to some degree of saturation of the spin ensemble while sweeping the magnetic field over the transitions. The highest collective coupling achieved is 357.8 kHz±2.8 kHz357.8\,\mathrm{kHz}\pm2.8\,\mathrm{kHz}, pumping the NV−^- with 695 s−1695\,\mathrm{s}^{-1}.

To amount for the microwave saturation we calculate the excitation rate due to the microwave probe tone. The input microwave signal is heavily attenuated to −55.7 dBm-55.7\,\mathrm{dBm} at the input of the microwave cavity to limit saturation of the spin transition. The microwave signal is further attenuated by the insertion loss to the fully undercoupled resonator, given by IL=−10log⁡4κ(1+κ)2IL=-10\log\frac{4\kappa}{(1+\kappa)^2}. Here, κ\kappa is the resonator coupling coefficient and is determined by fitting the resonator reflection signal to 0.155±0.002S310.155\pm0.002^{\mathrm{S31}}. This results in an insertion loss of 3.33 dBm3.33\,\mathrm{dBm}, leading to a final microwave power in the resonator of about −59 dBm-59\,\mathrm{dBm}. This corresponds to an average number of photons ⟨n⟩\langle n\rangle of 2.87×1082.87\times10^8 inside the resonator with a loaded quality factor of QL=33,500Q_L=33{,}500. The rate of excitation as well as for relaxation if given in SI-units by?

(dndt)MW=14n(gNVμBℏ)2B12g(ω−ωESR),(dndt)T1=n−n0T1.(7)\begin{aligned} \left(\frac{dn}{dt}\right)_{\mathrm{MW}}&=\frac{1}{4}n\left(\frac{g_{\mathrm{NV}}\mu_{\mathrm{B}}}{\hbar}\right)^2B_1^2g(\omega-\omega_{\mathrm{ESR}}),\\ \left(\frac{dn}{dt}\right)_{T_1}&=\frac{n-n_0}{T_1}. \tag*{(7)} \end{aligned}

Here, gNVg_{\mathrm{NV}} gives the NV−^- g-factor, μB\mu_{\mathrm{B}} the Bohr magneton, ℏ\hbar the Planck constant, T1T_1 being the longitudinal relaxation time, nn and n0n_0 are the relative spin population differences under optical pumping and pure Boltzmann distribution without pumping, respectively, both normalized by the total number of spins. The additional factor of 1/41/4 at the microwave excitation rate takes into account that the microwave energy can be absorbed by only one of the four NV−^- defect sub-sets. g(ω−ωESR)g(\omega-\omega_{\mathrm{ESR}}) gives the

Image not extracted

Figure 3 (PDF p. 9). Microwave reflection of low-field NV−^- transition. a Color encoded microwave reflection ∣S11∣|S_{11}| as a function of VNA frequency and static magnetic field, at a pump rate of 695 s−1695\,\mathrm{s}^{-1}. b Effective loss rate κeff\kappa_{\mathrm{eff}} of the resonator - spin ensemble hybrid system as a function of the static magnetic field. The orange solid line is a fit of Eq. (S4) to the data.

linewidth function of the homogeneously broadened spin packets in the sample for which we assume a Lorentzian lineshape?

g(ω−ωres)=T2π11+T22(ω−ωESR)2,(8)g(\omega-\omega_{\mathrm{res}})=\frac{T_2}{\pi}\frac{1}{1+T_2^2(\omega-\omega_{\mathrm{ESR}})^2}, \tag*{(8)}

where the spin-spin relaxation time is given by T2T_2 and (ω−ωres)(\omega-\omega_{\mathrm{res}}) gives the detuning from the resonance frequency of the spin transition ωESR\omega_{\mathrm{ESR}}. We estimate the rate of excitation via an averaged B1,avgB_{1,\mathrm{avg}} field strength, determined by finite element simulations of the sapphire ring resonatorS28 to B1,avg=1.5×10−7 TB_{1,\mathrm{avg}}=1.5\times10^{-7}\ \mathrm{T}. On resonance and with T2=25 μsT_2=25\ \mu\mathrm{s}, determined by conventional pulsed ESR, we estimate an excitation rate of 93.0 s−193.0\ \mathrm{s}^{-1}. At maximal laser pump rates, T1=1.5 msT_1=1.5\ \mathrm{ms} (see previous section) and the rate of relaxation results in 45.9 s−145.9\ \mathrm{s}^{-1}. The population difference nn is calculated for an optical pump rate of 695 s−1695\ \mathrm{s}^{-1}, following the rate equation formalism presented in S29. With the rate of excitation being about twice as high as the relaxation rate the spins are partially saturated. Comparing the calculated spin populations with and without a microwave drive we find that the microwave drive is reducing the population difference of the ∣0⟩→∣+1⟩\lvert0\rangle\to\lvert+1\rangle transition by 19.1%19.1\%. We scale the extracted value for the collective coupling geffg_{\mathrm{eff}} to remove the effects of saturation and yield geff/2π=390 kHz±3.1 kHzg_{\mathrm{eff}}/2\pi=390\ \mathrm{kHz}\pm3.1\ \mathrm{kHz}.

From the finite element simulations of the resonator we are able to determine an average single spin-photon coupling rate g0/2π=0.244 Hzg_0/2\pi=0.244\ \mathrm{Hz}. Assuming a homogeneous B1B_1-field over the diamond sample, and consequently a homogeneous distribution of g0g_0, the collective coupling is given by geff=g0Szg_{\mathrm{eff}}=g_0\sqrt{S_z}, with SzS_z being the population difference between the two spin states. With the un-saturated value for geffg_{\mathrm{eff}} we find Sz=2.57×1012S_z=2.57\times10^{12}. To find the total number of spins for a given hyperfine transition and single NV−^- defect axis, we scale SzS_z up to 100%100\% spin polarization. At a pump rate of 695 s−1695\ \mathrm{s}^{-1} we calculate a normalized population difference of 0.070.07 between (∣0⟩→∣+1⟩)(\lvert0\rangle\to\lvert+1\rangle). Together, we find a total number of spins per hyperfine transition and per NV−^- defect axis to N=3.67×1013N=3.67\times10^{13}. To get a good agreement of the threshold equation with the experimental data, we require to adjust the number of spins by a factor of 0.630.63, leading to a final number of spins of 2.32×10132.32\times10^{13}. An accurate determination of the absolute number of spins in a given sample is typically challenging and often only accurate to the order of magnitude. Having estimated NN within a third to arrive at an excellent agreement with the experimental data corroborates our method to determine NN.

Supplementary Note 4: Microwave Cavity and Resonator Design Details

As described in the main text, the cavity’s purpose is to suppress the radiation losses of the dielectric sapphire ring resonator. The dimensions are chosen such that the quality factor of the resonator is as large as possible, while still being able to be fitted inside of the poles of a normal conducting magnet system. Supplementary Figure 4 shows the technical drawing of the cavity, including all relevant dimensions. The body of the cavity is made of OFHC copper and is gold platted to protect the copper surfaces from oxidation. Prior gold platting a silver adhesion layer 1-2 μm\mu\mathrm{m} thickness was put on the copper followed by a 0.2-0.3 μm\mu\mathrm{m} gold layer. Since the conductivity of gold is lower than of pristine OFHC copper the thickness of the gold layer was kept minimal. The cavity is coupled via an iris to a standard X-band waveguide. The sapphire dielectric ring resonator is of cylindrical shape with an outer diameter of 10 mm10\ \mathrm{mm}, an inner diameter of 5.1 mm5.1\ \mathrm{mm} and a height of 6 mm6\ \mathrm{mm}. We determine the mode volume of the resonator to Vm=5.1×10−8 m3V_{\mathrm{m}}=5.1\times10^{-8}\ \mathrm{m}^3, via finite element simulationsS28. Together with the volume of the diamond of about Vdia=10−8 m3V_{\mathrm{dia}}=10^{-8}\ \mathrm{m}^3 the filling factor of the resonator with diamond sample is given by η=Vdia/Vm=0.2\eta=V_{\mathrm{dia}}/V_{\mathrm{m}}=0.2.

Image not extracted

Figure S4. Microwave Cavity Technical Drawing. The technical drawing shows the dimensions of the gold platted copper cavity.

References

  1. [1]¹Gordon, J. P., Zeiger, H. J. & Townes, C. H. The maser—new type of microwave amplifier, frequency standard, and spectrometer. Physical Review 99, 1264–1274 (1955).DOI
  2. [2]²Reid, M., Clauss, R., Bathker, D. & Stelzried, C. Low-noise microwave receiving systems in a worldwide network of large antennas. Proceedings of the IEEE 61, 1330–1335 (1973).DOI
  3. [3]³Makhov, G., Kikuchi, C., Lambe, J. & Terhune, R. W. Maser action in ruby. Physical Review 109, 1399–1400 (1958).DOI
  4. [4]⁴Goldenberg, H. M., Kleppner, D. & Ramsey, N. F. Atomic hydrogen maser. Physical Review Letters 5, 361–362 (1960).DOI
  5. [5]⁵Moi, L. et al. Rydberg-atom masers. i. a theoretical and experimental study of super-radiant systems in the millimeter-wave domain. Physical Review A 27, 2043–2064 (1983).DOI
  6. [6]⁶Oxborrow, M., Breeze, J. D. & Alford, N. M. Room-temperature solid-state maser. Nature 488, 353–356 (2012).DOI
  7. [7]⁷Breeze, J. et al. Enhanced magnetic purcell effect in room-temperature masers. Nature Communications 6, 6215 (2015).DOI
  8. [8]⁸Salvadori, E. et al. Nanosecond time-resolved characterization of a pentacene-based room-temperature maser. Scientific Reports 7, 41836 (2017).
  9. [9]⁹Jin, L. et al. Proposal for a room-temperature diamond maser. Nature Communications 6, 8251 (2015).DOI
  10. [10]¹⁰Breeze, J. D., Salvadori, E., Sathian, J., Alford, N. M. & Kay, C. W. M. Continuous-wave room-temperature diamond maser. Nature 555, 493–496 (2018).
  11. [11]¹¹Sherman, A. et al. Diamond-based microwave quantum amplifier. Science Advances 8, eade6527 (2022).DOI
  12. [12]¹²Koppenhöfer, M., Groszkowski, P., Lau, H.-K. & Clerk, A. Dissipative superradiant spin amplifier for enhanced quantum sensing. PRX Quantum 3, 030330 (2022).DOI
  13. [13]¹³Jiang, M. et al. Floquet spin amplification. Physical Review Letters 128, 233201 (2022).DOI
  14. [14]¹⁴Wu, H. et al. Enhanced quantum sensing with room-temperature solid-state masers. Science Advances 8, eade1613 (2022).arxiv.org/abs/2201.04298
  15. [15]¹⁵Gottscholl, A. et al. Superradiance of spin defects in silicon carbide for maser applications. Frontiers in Photonics 3 (2022).DOI
  16. [16]¹⁶Jiang, M., Su, H., Wu, Z., Peng, X. & Budker, D. Floquet maser. Science Advances 7, eabe0719 (2022).DOI
  17. [17]¹⁷Shtin, N. A., Romero, J. M. L. & Prokhorov, E. Theory of fundamental microwave absorption in sapphire (α-al2o3). Journal of Applied Physics 106, 104115 (2009).DOI
  18. [18]¹⁸Accatino, L. & Bertin, G. Design of coupling irises between circular cavities by modal analysis. IEEE Transactions on Microwave Theory and Techniques 42, 1307–1313 (1994).DOI
  19. [19]¹⁹For additional information see: Supplementary Material: Maser Threshold Characterization by Resonator Q-Factor Tuning.
  20. [20]²⁰Robledo, L., Bernien, H., Sar, T. v. d. & Hanson, R. Spin dynamics in the optical cycle of single nitrogen-vacancy centres in diamond. New Journal of Physics 13, 025013 (2011).DOI
  21. [21]²¹Fu, K.-M. C. et al. Observation of the dynamic jahn-teller effect in the excited states of nitrogen-vacancy centers in diamond. Physical Review Letters 103, 256404 (2009).
  22. [22]²²Doherty, M. W. et al. The nitrogen-vacancy colour centre in diamond. Physics Reports 528, 1–45 (2013).DOI
  23. [23]²³Mrózek, M. et al. Longitudinal spin relaxation in nitrogen-vacancy ensembles in diamond. EPJ Quantum Technology 2, 22 (2015).DOI
  24. [24]²⁴Jeong, K. et al. Understanding the magnetic resonance spectrum of nitrogen vacancy centers in an ensemble of randomly oriented nanodiamonds. Journal of Physical Chemistry C 121, 21057–21061 (2017).arxiv.org/abs/1707.07205
  25. [25]²⁵Gö ppl, M. et al. Coplanar waveguide resonators for circuit quantum electrodynamics. Journal of Applied Physics 104, – (2008).DOI
  26. [26]²⁶Kolobov, M. I., Davidovich, L., Giacobino, E. & Fabre, C. Role of pumping statistics and dynamics of atomic polarization in quantum fluctuations of laser sources. Physical Review A 47, 1431–1446 (1993).pubmed.ncbi.nlm.nih.gov/9909068
  27. [27]²⁷Haroche, S. & Raimond, J.-M. Exploring the quantum. Atoms, cavities and photons. Reprint of the 2006 hardback ed. (Oxford, Graduate Texts. Oxford: Oxford University Press., 2013).
  28. [28]²⁸Oskooi, A. F. et al. A flexible free-software package for electromagnetic netic simulations by the fdtd method. Computer Physics Communications 181, 687–702 (2010).
  29. [29]²⁹Sherman, A., Buchbinder, L., Ding, S. & Blank, A. Performance analysis of diamond-based masers. Journal of Applied Physics 129, 144503 (2021).
  30. [30]³⁰Jarmola, A., Acosta, V. M., Jensen, K., Chemerisov, S. & Budker, D. Temperature- and magnetic-field-dependent longitudinal spin relaxation in nitrogen-vacancy ensembles in diamond. Physical Review Letters 108, 197601 (2012).pubmed.ncbi.nlm.nih.gov/23003089
  31. [31]³¹Wang, P. et al. Novel method to measure unloaded quality factor of resonant cavities at room temperature. Nuclear Science and Techniques 29, 50 (2018).DOI

Paper details

vlnc:W_x5xr945h
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents