betaFeedback

WorksPhysics and Astronomy

High-Temperature Effects for Transition State Calculations in Solids

Abstract

Transition state calculation is a critical technique to understand and predict versatile dynamical phenomena in solids. However, the transition state results obtained at zero Kelvin are often utilized for prediction or interpretation of dynamical processes at high temperatures, and the error bars of such approximation are largely unknown. In this benchmark study, all the major temperature effects including lattice expansion, lattice vibration, electron excitation, and band-edge shift are evaluated with first-principles calculations for defects diffusion in solids. With inclusion of these temperature effects, the notable discrepancies between theoretical predictions at zero Kelvin and the experimental diffusivities at high temperatures are dramatically reduced. Particularly, we find that the lattice expansion and lattice vibration are dominant factors lowering the defect formation energies and hopping barriers at high temperatures, but the electron excitation exhibits minor effects. In sharp contrast to typical assumption, the attempt frequency with lattice expansion and vibration varies significantly with materials: several THz for aluminum bulk but surprisingly over 500 THz for 4H-SiC. For defects in semiconductors, the band-edge shift is also significant at high temperatures and plays a vital role in the defect diffusion. We expect this study would help accurately predict the dynamical processes at high temperatures.

Introduction

Transition state calculation of dynamical processes at high temperatures are essential to a range of fields, such as turbine engines, metallurgical processing, oxide film growth, and solid oxide fuel cells. As summarized in Figure 1, high temperatures can induce lattice expansion, lattice vibration, electron excitation, and band-edge shift. These effects are coupled and impact several aspects of a dynamical process, including hopping distance, defect concentration, attempt frequency, and activation barrier. Because of the complexity, most previous studies utilized transition state results at zero Kelvin to predict the processes occurring at high temperatures.[1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11]

Four types of temperature effects in solids

Figure 1. Four types of temperature effects, including lattice expansion, lattice vibration, electron excitation, and band-edge shift, in solids.

Although limited efforts have made to include certain temperature effects in transition state calculations,[12, 13, 14, 15, 16] none of them included all the temperature effects and the differences between metals and semiconductors remain largely unknown. For instance, only the contribution of lattice vibration was considered for the hopping barrier of metallic solute diffusion in silicon.[17] The contributions of lattice vibration to defect concentration and hopping barrier were considered for vacancy intermediated self-diffusion in lithium, but the lattice constants and attempt frequency were fixed to values at zero Kelvin.[18] Neugebauer et al. carefully examined the anharmonicity and vacancies near the melting point of aluminum, while the impacts on dynamics was unexplored.19 Therefore, a comprehensive evaluation of all the temperature effects consistently in representative systems are valuable to clarify their roles in dynamical processes at high temperatures.

In this benchmark study, we employ density functional theory (DFT) calculations to systematically examine all the four types of temperature effects on the hopping distance, defect concentration, attempt frequency, and activation barrier in a consistent manner. By closely examining several distinct diffusion processes, we clarify the impacts of those temperature effects and obtain results with much improved accuracies with respect to the experimental results at high temperatures.

Methods

Our ab initio calculations are carried out based on the spin-polarized DFT as implemented in the Vienna Ab initio Simulation Package.20 The electron excitation is included by adopting the Fermi-Dirac distribution with an energy smearing consistent with the examined temperature, the lattice expansion is included by using the experimental lattice constants (see § 10 of the supplementary material), and the lattice vibration are calculated with finite displacements and analyzed using the package phonopy.21 We also obtain the lattice lengths using first-principles calculations and the corresponding diffusivity resembles that based on the experimental lattice length (see § 11 of the supplementary material). For the aluminum system, the exchange-correlation functional is chosen in the form of Perdew-Burke-Ernzerhof (PBE).22 A self-consistent effective Hubbard U term,23 UeffU_{\mathrm{eff}}, is added for the dd electrons in Fe. Our tests show that the Hubbard U term is critical to obtain reasonable hopping barriers (see § 12 of the supplementary material). To accurately describe the electronic properties of 4H-SiC, we employ the Heyd–Scuseria–Ernzerhof hybrid functional (HSE06)24 for all calculations except the lattice vibration, which is too time-consuming using the hybrid functional and thus is calculated self-consistently with the PBE functional for PBE-relaxed structures. Tests of perfect 4H-SiC bulk show that PBE and HSE06 functionals give very close results (see § 13 of the supplementary material). An energy cutoff of 360, 481, and 450 eV is set to the plane-wave basis sets for the VAlV_{\mathrm{Al}}, FeAlFe_{\mathrm{Al}}, and VCV_{\mathrm{C}} systems, respectively, together with the following projector augmented-wave potentials:25 Al_GW(3s23p13s^{2}3p^{1}) for Al, Fe_GW(4s13d74s^{1}3d^{7}) for Fe, Si_GW(3s23p23s^{2}3p^{2}) for Si, and C_GW(2s22p22s^{2}2p^{2}) for C. The kk-point spacing of 2π/602\pi/60 and 2π/252\pi/25 Å−1^{-1} is used for the Al and the 4H-SiC supercells, which are about 12 and 10 Å in each direction, respectively. Convergence tests of energy cutoff, kk-point sampling, and supercell size can be found in § 12 of the supplemental material. The hopping barriers are calculated using the climbing nudged elastic band method.26

In the ab initio molecular dynamics (AIMD) simulation of VAlV_{\mathrm{Al}} diffusion, the canonical ensemble is carried out with the experimental lattice constants, and the simulation time varies from 560 to 3640 ps with a time step of 2 fs. The diffusion coefficient is determined by the mean squared displacement (MSD) as defined in Eq. (1),27

D(T)=16xD(T)xDsimlim⁡t→∞ddtMSD(t).(1)D(T) = \frac{1}{6}\frac{x_{\mathrm{D}}(T)}{x_{\mathrm{D}}^{\mathrm{sim}}}\lim_{t\to\infty}\frac{d}{dt}\mathrm{MSD}(t). \tag*{(1)}

Here, xDsimx_{\mathrm{D}}^{\mathrm{sim}} and xD(T)x_{\mathrm{D}}(T) is the defect concentration in the supercell and that based on Figure 2(b). The MSD trajectories are analyzed using the Molecular Dynamics Analysis of Neutron Scattering Experiments28 and the MSD results and diffusion coefficients are provided in § 14 of the supplemental material. The AIMD simulations of 4H-SiC bulk are carried out in the canonical ensemble using the PBE functional with a time step of 1.5 fs for 15 ps; the HSE06 functional is adopted to calculate the temperature dependence of band edges for 11-15 sampled AIMD structures.

Temperature dependence of hopping distance, vacancy concentration, attempt frequency, activation barrier, and diffusion coefficient

Figure 2. Temperature dependence of the (a) hopping distance, (b) vacancy concentration, (c) attempt frequency, (d) activation barrier, and (e) diffusion coefficient for VAlV_{\mathrm{Al}} diffusion in aluminum bulk. In panel (e), an attempt frequency of 5 THz is adopted for the calculations without lattice vibration.

Results and Discussions

In this study, we examine three representative dynamical processes at high temperatures, including aluminum vacancy, VAlV_{\mathrm{Al}}, diffusion in aluminum bulk through vacancy hopping in the range of 643–900 K, diffusion of substitutional defect, FeAl\mathrm{Fe}_{\mathrm{Al}}, in aluminum bulk though vacancy-assisted hopping in the range of 500–900 K, and carbon vacancy, VCV_{\mathrm{C}}, diffusion in 4H-SiC bulk through vacancy hopping in the range of 2173–2473 K. These systems are chosen because they represent dynamical processes in non-magnetic metal systems, dilute magnetic systems, and semiconductor systems, and also because they possess sufficient experimental data for an all-aspect verification.

VAlV_{\mathrm{Al}} Diffusion in Aluminum Bulk

Our first examined process is VAlV_{\mathrm{Al}} diffusion through vacancy hopping in aluminum bulk, which is an ideal system for accurate comparison and fast enough to be verified independently using AIMD. In contrast to the widely-used diffusivity formula shown in Eqs. 2(a-b), 29 we impose the temperature effects to every aspect in the diffusion coefficient of VAlV_{\mathrm{Al}}, including hopping distance, defect concentration, attempt frequency, and activation barrier, and update the formulas to Eqs. 3(a-b).

D(T)=Γfa2xDv0e−EbkBT(2)D(T)=\Gamma f a^2 x_D v_0 e^{-\frac{E_b}{k_B T}} \tag*{(2)}
xD(T)=e−EfkBT,(3)x_D(T)=e^{-\frac{E_f}{k_B T}}, \tag*{(3)}
D(T)=Γfa(T)2xD(T)v0(T)e−Eb(T)kBT(4)D(T)=\Gamma f a(T)^2 x_D(T)v_0(T)e^{-\frac{E_b(T)}{k_B T}} \tag*{(4)}
xD(T)=e−Gf(T)kBT,(5)x_D(T)=e^{-\frac{G_f(T)}{k_B T}}, \tag*{(5)}

where Γ\Gamma and ff are geometric factor and correlation factor, which equals 2 and 0.7815 for FCC structure, 30 respectively; aa is hopping distance; xDx_D is fractional concentration of aluminum vacancy; v0v_0 is attempt frequency; EfE_f and GfG_f is the internal energy and Gibbs free energy for a dilute aluminum vacancy, respectively; and EbE_b is the activation barrier of the hopping process.

The attempt frequency was typically treated in one of two ways: a constant in the range of 11–1010 THz31, 32 or a statistical expression initially for molecular systems (Eq. 4a).33 Here, we extend the formula to solids by averaging over all the kk-points in the Brillouin zone and include the temperature dependence, as shown in Eq. 4b.

ν0=∏jγjIS∏jγjTS,(6)\nu_0 = \frac{\prod_j \gamma_j^{IS}}{\prod_j \gamma_j^{TS}}, \tag*{(6)}
ν0(T)=(∏j,kγj,kIS(T)∏j,kγj,kTS(T))1/nk,(7)\nu_0(T) = \left(\frac{\prod_{j,k} \gamma_{j,k}^{IS}(T)}{\prod_{j,k} \gamma_{j,k}^{TS}(T)}\right)^{1/n_k}, \tag*{(7)}

where nkn_k is the number of sampled kk-points in the Brillouin zone; γj,kIS\gamma_{j,k}^{IS} and γj,kTS\gamma_{j,k}^{TS} are, respectively, the positive vibration frequency of the initial and transition state for the phonon branch jj at point kk in reciprocal space. Given the definition of transition state, the number of γj,kTS\gamma_{j,k}^{TS} is one less than that of γj,kIS\gamma_{j,k}^{IS} at each kk-point. Note that since Eqs. 4(a-b) already incorporate the entropy of activation barrier, the Eb(T)E_b(T) term in Eq. 3a should solely represent internal energy. However, if Eb(T)E_b(T) is associated with free energy with entropy contribution, the attempt frequency must be expressed as kBTh\frac{k_BT}{h}.34, 35

In this work, we consider the thermal expansion by adoption of the experimental lattice constants, 36 which increases by ~2.0% at 900 K relative to that at 300 K [Figure 2(a)]. Figure 2(b) compares the vacancy concentration predicted at different levels of thermal corrections with the experiments in the range of 643–900 K. 37–39 The electron excitation is found to play a minor role, with the results being 0.85–0.88 times of the 0 K results. Here, “0 K” means none of the lattice expansion, lattice vibration, and electron excitation is included. However, further inclusion of the lattice expansion decreases the vacancy concentration to 0.29–0.21 times of that with electron excitation, and lattice vibration dramatically increases it to 15.25–15.50 times of that with lattice expansion. In total, all the temperature effects induce an increasing vacancy concentration 3.78–2.88 times of that at 0 K.

Figure 2(c) shows that the attempt frequency based on our extended formula of Eq. 4b predicts a slow decrease trend from 5.6 to 5.2 THz in the range of 643–900 K. Relative to the values based on the molecular formula of Eq. 4a, they are around 0.2 THz higher. By contrast, the classical mechanics formula of Eq. 4a incorrectly predicts an increase of attempt frequency from 13.40 to 18.75 THz in the same temperature range.

Figure 2(d) compares the temperature effects on activation barrier. The electron excitation is found to induce a negligible decrease of around 1 meV relative to that at 0 K. The lattice expansion decreases the hopping barrier by 0.05–0.10 eV in the range of 643–900 K, and the lattice vibration further decreases it by 0.05–0.08 eV. In total, the lattice expansion and vibration decrease the hopping barrier almost linearly from 0.11 eV at 643 K to 0.17 eV at 900 K, about twice of the thermal energy kBTk_{\mathrm{B}}T. Relative to previous studies without considering the full temperature effects and/or with potentially insufficient computational accuracy, [13] [19, 40, 41] noticeable differences are observed in the formation energy, migration barrier, and attempt frequency, as shown in § 15 of the supplementary material.

Figure 2(e) further compares the temperature dependence of diffusivity among results with different thermal corrections and experimental data. 42–44 To independently examine the accuracy and computational cost of the thermal corrections, we also carried out AIMD simulations in the temperature range of 643–900 K up to 0.5–3.6 ns. Our results show that the electron excitation and lattice expansion induce slight changes relative to that at 0 K, and they are about 1/15–1/19 times of the experimental values. By contrast, the diffusivities with all the thermal corrections are significantly improved and agree reasonably well with both experiments and the AIMD results. However, the AIMD simulations in this example are about 10310^{3} times more time-consuming than calculations with all the thermal corrections. Therefore, this example clearly indicates that including the thermal corrections and utilizing the Eqs. 3a-3b and 4b, we can largely address the underestimated diffusivity at 0 K and predict reliable diffusivity at high temperatures.

FeAl Diffusion in Aluminum Bulk

To evaluate the thermal corrections for more complex systems, we examine the vacancy-assisted diffusion of FeAl in Al bulk from 500 to 900 K. The diffusion of such dynamical process is often described by the five-frequency model,45 which involves five frequencies ω0\omega_0–ω4\omega_4 related to the hoppings of vacancy far away or near a dilute solute. Because ω2/ω1\omega_2/\omega_1 is close to zero in this specific case, the five-frequency model can be simplified to three frequencies of ω2\omega_2–ω4\omega_4 (see section S7 of the supplementary material), the thermal effects of which we will focus on. Here, both the hopping distance and vacancy concentration are same as Figure 2(a-Figure 2b). Figure 3(a) shows that the attempt frequency varies with processes and exhibits a decreasing trend with temperature, similar to that of aluminum vacancy diffusion in Figure 2(c). Specifically, the attempt frequency of ω2\omega_2–ω4\omega_4 decreases from 3.3 to 2.2 THz, from 6.0 to 3.5 THz, and from 9.0 to 8.1 THz, respectively.

Temperature dependence of attempt frequency and activation barriers, and comparison of diffusion coefficients

Figure 3. Temperature dependence of (a) attempt frequency and (b–d) activation barriers for processes ω2\omega_2–ω4\omega_4, and (e) comparison among theoretical diffusion coefficients with different temperature effects and experimental results46-48 for FeAl diffusion in aluminum bulk.

For the temperature dependence of hopping barriers, the electron excitation is found to be trivial, with changes less than 10 meV Figure 3(b–Figure 3d). By contrast, the lattice expansion decreases the EbE_b of ω2\omega_2–ω4\omega_4 from 0.05 to 0.20 eV, from 0.03 to 0.15 eV, and from 0.12 to 0.20 eV in the range of 500–900 K, respectively. The lattice vibration decreases EbE_b further and the whole temperature effects decrease EbE_b of ω2\omega_2–ω4\omega_4 from 0.09 to 0.28 eV, from 0.08 to 0.22 eV, and from 0.16 to 0.27 eV in the range of 500–900 K, respectively. These energy changes are about 1.8–3.6 times of the thermal energy kBTk_B T. Compared to previous work with partial temperature effects and without Hubbard U interactions[2], noticeable differences in migration barriers and attempt frequencies are observed (see § 15 of the supplementary material).

Figure 3(e) shows that the total temperature effects increase the diffusion coefficients to 213.6–312.2 times of those at 0 K in the range of 500–900 K. Compared with the experimental results,46-48 the theoretical predictions with all temperature effects agrees well with the experiments around 900 K, although noticeably higher predictions than the experimental values are observed around 700 K. Two potential reasons could contribute to such discrepancy. First, the error bar of experimental data may be higher at low temperatures because of the significantly slow dynamical processes. Second, the transition metal iron may need an improved description beyond the current Hubbard U method. We compare an effective UeffU_{eff} of 0, an empirical value of 3 eV,49, 50 and a self-consistent value of 2.7 eV for ω2\omega_2 at 0 K, and the respective activation barrier is calculated to be 1.33, 0.74, and 0.79 eV (see § 12 of the supplementary material). Although the self-consistent UeffU_{eff} is possibly the optimal choice at hand, we are open to the possibility that further improvement could be made in the future. With improved experimental data, more accurate description of transition metal element, and the high temperature corrections proposed in this work, a better agreement should be reached in the future.

VCV_\mathrm{C} Diffusion in 4H-SiC Bulk

Different from metallic systems, defects in semiconductors or insulators could be charged and experience a transition-state-redox effect during dynamical processes,[1] namely that the transition state possesses a different charge state from that of the initial/final state in certain Fermi level range. Moreover, the band edges of semiconductors and insulators can change dramatically with temperature and consequently impact the Fermi energy and defect concentration. To evaluate the temperature effects in semiconductors, we examine the VCV_\mathrm{C} diffusion through vacancy hopping in 4H-SiC bulk in the same temperature range of 2373–2573 K as previous experiments.51 The diffusion coefficient of VCV_\mathrm{C} follows Eq. 3a-b, except that the geometric factor Γ\Gamma is 0.75,[12] [52] and the correlation factor is 0.7815 in the direction [1] of a hexagonal system.53 The formation energy GfG_f of a defect DqD^q with charge state qq is updated to Eq. (8) based on the original formula,54

Gf(Dq,EF)≡Gtot(Dq,T)+δFNV(Dq,T)−Gtot(bulk,T)+∑μi(T)+q[EVBM(bulk,T)+EF(T)],(8)G_f(D^q,E_F) \equiv G_{tot}(D^q,T) + \delta F_{NV}(D^q,T) - G_{tot}(bulk,T) + \sum\mu_i(T) + q[E_{VBM}(bulk,T) + E_F(T)], \tag*{(8)}

where Gtot(Dq,T)G_{tot}(D^q,T) and Gtot(bulk,T)G_{tot}(bulk,T) are the free energies of the system with defect DqD^q and perfect bulk at temperature TT, respectively; δFNV\delta F_{NV} is the FNV correction with an experimental dielectric constant of 9.76ε09.76\varepsilon_0 to reduce image charge interactions under periodic boundary conditions;1 In the correction, the experimental dielectric constant is used; μi(T)\mu_i(T) is the chemical potential of element ii to balance the composition between the perfect bulk and defective system, and μC(T)\mu_C(T) of graphite is used in this case; EVBM(bulk,T)E_{VBM}(bulk,T) and EF(T)E_F(T) are the valence band maximum (VBM) energy and Fermi energy relative to the VBM energy at temperature TT, respectively.

We first examine the temperature dependence of VBM, EVBM(bulk,T)E_{VBM}(bulk,T). AIMD simulations of 4H-SiC bulk are carried out using the PBE functional with experimental lattice constants for 15 ps and sampled AIMD structures are further calculated using HSE06 functional to obtain the band edges and Si-2p energy level [Fig. 4(a-b)]. Figure 4(c) indicates that the VBM increases slightly with temperature by 0.04 eV at 2473 K relative to that at 0 K, but the CBM decreases dramatically by 1.26 eV. The predicted band gap of 1.9 eV at 2473 K is reasonably consistent with the experimental value of 2.2 eV.56 The energy level of Si-2p decreases by 0.9 eV from 0 to 2473 K and a linear interpolation in the range of 873-1623 K corresponds to an energy decrease of 0.27 eV, consistent with the value of 0.21 eV according to X-ray photoelectron spectroscopy.57, 58 Further charge density analyses reveal that the VBM of 4H-SiC is tightly bound to the C atoms, but the CBM is distributed inside the hollow space of the crystal structure (see § 17 of the supplementary material). Such feature is expected to induce easier changes of the CBM by the structural distortion at high temperatures than the VBM.

Band edges and Si-2p level for 4H-SiC bulk at sampled time steps for AIMD simulations

Figure 4. Band edges and Si-2p level for 4H-SiC bulk at sampled time steps for AIMD simulations at (a) 1373 and (b) 2473 K; (c) temperature dependence of band edges and Si-2p for 4H-SiC bulk.

Then we examine the charge state and formation energy of VCV_{\mathrm{C}} in the initial and transition states, with consideration of the lattice expansion, lattice vibration, electron excitation, and band-edge shift. Figure 5(a) shows that the initial ground state of VCV_{\mathrm{C}} exhibits 2+, 1+, and 0 charge state in the Fermi level range of 0-0.66, 0.66-0.95, and 0.95-1.86 eV, respectively, at 2373 K. By contrast, the transition state of VCV_{\mathrm{C}} hopping exhibits 2+, 1+, and 0 charge state in the range of 0-0.20, 0.20-0.68, and 0.68-1.86 eV, respectively. Therefore, the initial and transition state possess different charge states in the Fermi level range of 0.20-0.66 and 0.68-0.95 eV, a phenomenon named as transition state redox 1. Similar features are also observed at 2473 and 2573 K [Fig. 5(b-c)]. For 4H-SiC bulk, the intrinsic Fermi level is calculated to be 1.04, 1.03, and 1.01 eV at 2373, 2473, and 2573 K, respectively, according to the charge neutrality relationship in Eq. (9).

Defect formation energy of the initial state and transition state during the $V_{\mathrm{C}}$ hopping in 4H-SiC

Figure 5. Defect formation energy of the initial state (IS) and transition state (TS) during the VCV_{\mathrm{C}} hopping in 4H-SiC at (a) 2373, (b) 2473, and (c) 2573 K with all temperature effects and (d-f) corresponding plots without lattice vibration. The blue number beside each segment labels its charge state and the vertical violet dashed line indicates the Fermi level in intrinsic 4H-SiC.

∫−∞EVBM(T)DOS[E+EVBM(0)−EVBM(T)]1+eE−EFkBT dE=∫ECBM(T)∞DOS[E+ECBM(0)−ECBM(T)]1+eE−EFkBT dE,(9)\int_{-\infty}^{E_{\mathrm{VBM}}(T)} \frac{DOS[E+E_{\mathrm{VBM}}(0)-E_{\mathrm{VBM}}(T)]}{1+e^{\frac{E-E_{\mathrm{F}}}{k_{\mathrm{B}}T}}}\,\mathrm{d}E = \int_{E_{\mathrm{CBM}}(T)}^{\infty} \frac{DOS[E+E_{\mathrm{CBM}}(0)-E_{\mathrm{CBM}}(T)]}{1+e^{\frac{E-E_{\mathrm{F}}}{k_{\mathrm{B}}T}}}\,\mathrm{d}E, \tag*{(9)}

where EVBM(T)E_{\mathrm{VBM}}(T) and ECBM(T)E_{\mathrm{CBM}}(T) are the VBM and CBM energy at TT, respectively; DOS(E)DOS(E) is the density of state at 0 K. Here, a rigid shift of the valence bands and conduction bands obtained at 0 K according to the EVBM(T)E_{\mathrm{VBM}}(T) and ECBM(T)E_{\mathrm{CBM}}(T) in Figure 4(c) is utilized. More rigorous calculations using the average DOS of AIMD structures gives similar result (see § 18 of the supplementary material). According to the Fermi levels and Figure 5(a-Figure 5c), the charge state of VCV_{\mathrm{C}} in intrinsic 4H-SiC are 0 in both the initial and transition states under the three temperatures. The corresponding defect formation energies and hopping barriers of VCV_{\mathrm{C}} can also be easily obtained. For comparison, the calculations with only the electron excitation, lattice expansion, and band-edge shift predict VCV_{\mathrm{C}} to be 1+ in its initial state [Figure 5(d-Figure 5f)], and those without any temperature effects predict it to be 2+ (see section S10 of the supplementary material). For transition state, its charge state is 0 at all levels of thermal corrections. Therefore, the temperature effects are critical in determining the charge state and formation energy of defects in semiconductors and insulators.

Figure 6 summarizes the temperature dependences of hopping distance, vacancy concentration, attempt frequency, hopping barrier, and diffusion coefficient. Experimental result in Figure 6(a) shows that the lattice expansion of 4H-SiC in the range of 2373–2573 K is about 1.2% relative to that at 300 K.59 As for the vacancy concentration, the electron excitation slightly decreases it to 0.66–0.68 times of that at 0 K. The lattice expansion increases the vacancy concentration to 2.09–2.35 times of that with only the electron excitation, and the lattice vibration further increases it by 111.52–113.42 times. In total, all the temperature effects increase the vacancy concentration to 153.25–181.30 times of that at 0 K, significantly more than that in aluminum bulk [Figure 2(b)].

Temperature dependence and phonon density of states for vacancy diffusion

Figure 6. FIG. 6. Temperature dependence of (a) hopping distance, (b) vacancy concentration, (c) attempt frequency of VCV_\mathrm{C} diffusion along the [1] direction of 4H-SiC bulk. Comparison of phonon DOS between (d) 4H-SiC bulk at 2473 K and aluminum bulk at 726 K, and phonon DOS of the initial and transition states for (e) VCV_\mathrm{C} hopping in 4H-SiC bulk at 2473 K and (f) VAlV_\mathrm{Al} hopping aluminum bulk at 726 K; (g) hopping barrier and (h) diffusion coefficient of VCV_\mathrm{C} in 4H-SiC bulk. The LO-TO splitting is included in the phonon DOS of 4H-SiC bulk (see the effects of LO-TO splitting in section S11 of the supplementary material).

Surprisingly, we find that the attempt frequency in 4H-SiC reaches 530–641 THz in the range of 2373–2573 K [Figure 6(c)], about 100 times of the typical values in aluminum bulk [Figure 2(c) and 3(a)] or about 20 times of the Debye frequency in 4H-SiC. Such high attempt frequency can be ascribed to two reasons. First, the large Young's modulus of 4H-SiC (∼450\sim450 GPa) relative to that of aluminum bulk (∼69\sim69 Pa) induces much higher phonon frequencies in the former [Figure 6(d)]. Consequently, the ratio of positive phonon frequencies between the initial and transition state is greater in 4H-SiC than that in aluminum bulk according to Eq. 4b. Second, the phonon DOS of transition state is slightly red-shifted by 0.33–0.43 THz in 4H-SiC [Figure 6(e)], while in aluminum bulk, the transition state phonon DOS is blue-shifted by about 0.10 THz [Figure 6(f)]. These noticeable redshifts also contribute to the high attempt frequency in 4H-SiC.

The hopping barrier of VCV_\mathrm{C} along the [1] direction of 4H-SiC is found to be 4.07 eV without any temperature effects, and the electron excitation decreases it slightly by 0.02–0.03 eV in the examined temperature range [Fig. 6(g)]. When the lattice expansion is included, the barrier is increased by 0.13–0.16 eV. With the lattice vibration, however, it is decreased by 0.71–0.74 eV. Such reduction of hopping barrier is also observed by comparing with earlier predictions with partial or without any temperature effects (see section S6 of the supplementary material). The overall diffusion coefficient of VCV_\mathrm{C} in [Fig. 6(h)] shows that the result at 0 K with a 5 THz attempt frequency is ∼\sim5 orders lower than the experiment.51 The electron excitation and lattice expansion slightly decrease the diffusion coefficient relative to that at 0 K. By contrast, the lattice vibration increases it by 3.6×1053.6 \times10^{5}–4.0×1054.0 \times10^{5} times. With all the temperature effects, the diffusion coefficient agrees satisfactorily with the experiments.

Conclusion

In summary, we propose a scheme for accurate transition state calculation under high temperatures and apply it to three diffusion processes: VAlV_{\mathrm{Al}} diffusion in Al bulk, substitutional defect FeAl\mathrm{Fe}_{\mathrm{Al}} diffusion in Al bulk, and VCV_{\mathrm{C}} diffusion in 4H-SiC bulk. Our first-principles calculations reveal that electron excitation has a minor influence on diffusion coefficient, and lattice expansion induces a limited improvement on the prediction of diffusion coefficient. The lattice vibration, however, exhibits a remarkable impact on diffusion coefficient. For semiconductors and insulators, band-edge shift can be significant at high temperatures and is critical to determine the charge state, defect formation energy, and activation barrier. Contrary to the conventional assumption, the attempt frequency is found to vary with temperature and can differ significantly between materials. Overall, inclusion of all the temperature effects reduce the defect formation energies and activation barriers; the diffusion coefficients are dramatically increased relative to those at 0 K and significantly improved agreements with experiments are obtained.

Supplementary Material

See the supplementary material for the experimental lattice constants of aluminum bulk and 4H-SiC bulk; lattice constants of aluminum bulk and 4H-SiC bulk predicted by first-principles calculations and impacts on dynamics; tests of kk-point mesh, Hubbard U value, energy cutoff, and supercell size; tests of vibrational free energy of 4H-SiC bulk; AIMD results of VAlV_{\mathrm{Al}} diffusion in aluminum bulk; five-frequency model for FeAl\mathrm{Fe}_{\mathrm{Al}} diffusion in aluminum bulk; comparison with theoretical literature; charge density of VBM and CBM in 4H-SiC bulk; DOS and intrinsic Fermi level of 4H-SiC bulk at 2473 K; defect formation energy of VCV_{\mathrm{C}} in 4H-SiC bulk at 0 K; effects of LO-TO splitting on the phonon DOS, attempt frequency, and diffusivity of VCV_{\mathrm{C}} in 4H-SiC bulk at 2473 K.

Acknowledgement

This work was financially supported by the Guangdong Provincial Key Laboratory of Computational Science and Material Design (Grant No. 2019B030301001), the Introduced Innovative R&D Team of Guangdong (Grant No. 2017ZT07C062), and the Shenzhen Science and Technology Innovation Committee (No. JCYJ20200109141412308). The first-principles calculations were carried out on the Taiyi cluster supported by the Center for Computational Science and Engineering of Southern University of Science and Technology and also on The Major Science and Technology Infrastructure Project of Material Genome Big-science Facilities Platform supported by Municipal Development and Reform Commission of Shenzhen.

AUTHOR DECLARATIONS

Conflict of Interest

The authors have no conflicts to disclose.

Author Contributions

Chengxuan Ke: Data curation (lead); Formal analysis (equal); Methodology (supporting); Writing – original draft (lead); Writing – review & editing (supporting). Chenxi Nie: Formal analysis (supporting). Guangfu Luo: Conceptualization (lead); Formal analysis (equal); Funding acquisition (lead); Methodology (lead); Resources (lead); Supervision (lead); Writing – review & editing (lead).

DATA AVAILABILITY

The data that support the findings of this study are available from the corresponding author upon reasonable request.

Supplemental Material for "High-Temperature Effects for Transition State Calculations in Solids"

Chengxuan Ke; Chenxi Nie; Guangfu Luo

Experimental lattice constants of aluminum bulk and 4H-SiC bulk

Tables S1 and S2, respectively, list the lattice constants of aluminum bulk and 4H-SiC bulk at different temperatures based on experimental results.[1, 2]

TT (°C)0100200300400500600650
a=b=ca = b = c (Å)4.03914.04864.05924.07014.08204.09474.10874.1162

Table S1. Lattice constants of aluminum bulk measured at different temperatures.[1]

TT (°C)1900210022002300
aa (Å)9.3399.3509.3569.361
cc (Å)10.18910.20110.20810.214

Table S2. Lattice constants of 4H-SiC bulk calculated accordingly to the formula obtained experimentally.[2]

Lattice constants of aluminum bulk and 4H-SiC bulk predicted by first-principles calculations and impacts on dynamics

The lattice parameters can also be predicted using first-principles calculations according to the free energy diagram as a function of the lattice constants and temperature. Here, the free energy consists of the internal energy and the vibrational free energy. The PBE and HSE06 functional is used for the Al bulk and 4H-SiC bulk, respectively. As shown in Figure S1-Figure S1), the predicted lattice length of Al bulk is about 0.09 Å or 0.8% greater than the experiments in the range of 643-900 K, and the predicted lattice length of 4H-SiC is about 0.07 Å or 0.8% greater than the experiments in the range of 2173-2573 K. Tests of the self-diffusion in Al bulk at 643 K show that the predicted lattice length leads to the hopping distance, attempt frequency, and exp⁡[−Gf(T)+Eb(T)kBT]\exp\left[-\frac{G_f(T)+E_b(T)}{k_B T}\right] being 1.01, 0.94, and 0.82 times of the respective value obtained using the experimental lattice length. Overall, the self-diffusion coefficient at 643 K is 0.78 times of the value based on the experimental lattice length, as shown in Fig. S1(c).

Free energy diagrams and self-diffusion coefficient comparison for aluminum bulk and 4H-SiC bulk

Figure S1. Free energy diagram as a function of lattice length and temperature for (a) aluminum bulk and (b) 4H-SiC bulk; the red dashed line is the predicted lattice length based on the minimum of free energy diagram and the blue line corresponds to the experimental values;[1, 2] (c) comparison of self-diffusion coefficient in aluminum bulk among experiments,[3, 4, 5] prediction based on experimental lattice constants, and prediction based on the DFT lattice length in (a).

Tests of kk-point mesh, Hubbard U value, energy cutoff, and supercell size

Figure S2 shows the convergence test of kk-point mesh for the formation energy and hopping barrier of VAlV_{\mathrm{Al}} in aluminum bulk at 0 K. According to these tests, a kk-point mesh of 5×5×55 \times5 \times5 is finally used, and the corresponding formation energy and hopping barrier are 0.63 and 0.61 eV, and the corresponding error bars are less than 18 and 3 meV, respectively.

Figure S2. (a) kk-point test of VAlV_{\mathrm{Al}} formation energy and hopping barrier in aluminum bulk at 0 K. (b) Effect of UeffU_{\mathrm{eff}} on EbE_b of ω2\omega_2–ω4\omega_4 in the diffusion of FeAl\mathrm{Fe}_{\mathrm{Al}} in aluminum bulk at 0 K. (c) Energy cutoff test for the formation energy EfE_f and hopping barrier EbE_b of VC2+V_{\mathrm{C}}^{2+} in 4H-SiC with HSE06 functional at 0 K. (d) Supercell size tests of VC2+V_{\mathrm{C}}^{2+} formation energy in 4H-SiC bulk at the PBE functional level. The Fermi level is set to the middle of band gap and LL is defined as V1/3V^{1/3}, where VV is the supercell volume. With the FNV correction, the error of a 72-atom supercell is around 0.09 eV relative to the value at the dilute limit (1/L→01/L \to0), which is also extrapolated from the raw data using polynomial.2

Figure S2 compares the hopping barriers of ω2\omega_2–ω4\omega_4 at 0 K for FeAl\mathrm{Fe}_{\mathrm{Al}} diffusion in Al bulk using different Hubbard U values. We find that the ω2\omega_2 process is particularly sensitive to UeffU_{\mathrm{eff}}: the activation barrier is 1.33 and 0.74 eV with UeffU_{\mathrm{eff}} of 0 and an empirical value of 3 eV,[7, 8] respectively. Such large difference highlights the importance of accurate description of 3dd electrons and probably explains the significant underestimation of the FeAl\mathrm{Fe}_{\mathrm{Al}} diffusion in aluminum bulk in literature.3 A self-consistent method based on the linear response approach4 predicts an UeffU_{\mathrm{eff}} of 2.7 eV for FeAl\mathrm{Fe}_{\mathrm{Al}} in Al bulk. This approach was designed to comply with a property of the exact density functional: the total energy as a function of electron occupation exhibits a piecewise linearity.5 Therefore, we choose Ueff=2.7U_{\mathrm{eff}} = 2.7 eV for our final calculations, and the corresponding activation barriers are 0.79, 0.61, and 0.71 eV for the ω2\omega_2–ω4\omega_4 processes, respectively.

Figure S2 shows the convergence test of energy cutoff for the formation energy EfE_f and hopping barrier EbE_b of VC2+V_{\mathrm{C}}^{2+} in 4H-SiC bulk at 0 K. It turns out that an energy cutoff of 450 eV converges the formation energy and hopping barrier at the level of 0.08 and 0.01 eV, respectively, which are supposed to be low.

Figure S2 shows the supercell size tests for the VC2+V_{\mathrm{C}}^{2+} in 4H-SiC bulk. It is found that, with the FNV correction, the formation energy of a 72-atom supercell is ∼\sim0.09 eV or ∼\sim2.0% greater than that of the 576-atom supercell. Since the image charge interaction decreases as the charge decrease, the error bars for VC+V_{\mathrm{C}}^{+} and VC0V_{\mathrm{C}}^{0} are expected to be even less.

Tests of vibrational free energy of 4H-SiC bulk

Figure S3 compares the vibrational free energies per formula of 4H-SiC bulk calculated self-consistently with the PBE and HSE06 functional. The PBE and HSE06 results agree well in the temperature range of 0–2500 K and follows a linear relationship. Such agreement supports the reliability of the PBE vibrational results.

Vibrational free energies per formula of 4H-SiC bulk versus temperature and linear relationship between the PBE and HSE06 results

Figure S3. (a) Vibrational free energies per formula of 4H-SiC bulk versus temperature for the PBE and HSE06 results. (b) Linear relationship between the PBE and HSE06 results.

AIMD results of VAlV_{\mathrm{Al}} diffusion in aluminum bulk

Figure S4(a) shows the mean squared displacements (MSD) of VAlV_{\mathrm{Al}} diffusion in aluminum bulk obtained at different temperatures. The first 2×1042 \times10^{4} time-steps have been discarded to ensure that the system reaches thermal equilibrium, and the nonlinear part of the MSD data at the end of AIMD simulation is not considered for linear fitting because of the insufficient data points. The calculated diffusion coefficient exhibits a perfect linear relationship as shown in Figure S4.

MSD results and temperature dependence of diffusion coefficient for VAl diffusion in aluminum bulk

Figure S4. (a) MSD results from 643 to 900 K and (b) temperature dependence of diffusion coefficient for VAlV_{\mathrm{Al}} diffusion in aluminum bulk

To clarify if there is any diffusion path different from the vacancy-hopping mechanism utilized in our transition state calculations, we examine the atomic coordinates before and after each hopping, as exemplified in Figure S5-Figure S5). It is found that all the hoppings exhibit a hopping distance of 2.75±0.252.75 \pm0.25 Å (Figure S5), which is consistent with the neighboring Al-Al distance of 2.912.91 Å. Further direct visualization of the hopping events also confirms the vacancy-hopping mechanism for the self-diffusion in Al bulk.

Atomic coordinates and statistics of hopping distance for one hopping atom in VAl diffusion in Al bulk

Figure S5. Atomic coordinates of (a) XX, (b) YY, and (c) ZZ direction of one hopping atom in the AIMD simulation of VAlV_{\mathrm{Al}} in Al bulk at 900 K. Dashed line represents the mean value before and after a hopping. (d) Statistics of hopping distance in the 900 K AIMD simulation with 55 hoppings in total.

Comparison with theoretical literature

DynamicsGfG_f (eV)EbE_b (eV)ν0\nu_0 (THz)DD (m2^2/s)Supercell size, energy cutoff, functional/method, temperature effectsRef.
VAlV_{\mathrm{Al}} hopping in Al bulk (643 K ≤T≤\le T \le 900 K)0.63–0.60i^{\mathrm{i}}———64 atoms, 204 eV, PW91 Lattice vibration[12]
0.57–0.57 0.60–0.56ii^{\mathrm{ii}}———108 atoms, 190 eV/462 eV, PBE Lattice expansion Lattice vibration Electron excitation[13]
0.62–0.600.61i^{\mathrm{i}}8.4 (Debye frequency)5×10−165\times10^{-16}–5×10−135\times10^{-13}80 atoms, 130 eV, PW91 Lattice vibration[14]
0.63–0.61i^{\mathrm{i}}0.57i^{\mathrm{i}}19.39×10−169\times10^{-16}–7×10−137\times10^{-13}32 atoms, 300 eV, PBW Lattice expansion Lattice vibration[15]
0.56–0.550.50–0.435.63–5.224×10−154\times10^{-15}–2×10−122\times10^{-12}108 atoms, 360 eV, PBE Lattice expansion Lattice vibration Electron excitationThis work
FeAl hopping in Al bulk (500 K ≤T≤\le T \le 900 K)0.48 (VAlV_{\mathrm{Al}})1.43 (Eb2E_{b2}) 0.62 (Eb3E_{b3}) 0.65 (Eb4E_{b4})3.90 (ν2\nu_2) 4.27 (ν3\nu_3) 5.30 (ν4\nu_4)4×10−274\times10^{-27}–9×10−189\times10^{-18}108 atoms, 350 eV, PBE Lattice vibration for ν0\nu_0[9]
0.56–0.55 (VAlV_{\mathrm{Al}})0.70–0.51 (Eb2E_{b2}) 0.54–0.39 (Eb3E_{b3}) 0.55–0.44 (Eb4E_{b4})3.34–2.16 (ν2\nu_2) 6.01–3.51 (ν3\nu_3) 9.02–8.12 (ν4\nu_4)1×10−191\times10^{-19}–5×10−135\times10^{-13}108 atoms, 481 eV, PBE+U Lattice expansion Lattice vibration Electron excitationThis work
VC0V_{\mathrm{C}}^0 hopping in 4H-SiC bulk (2373 K ≤T≤\le T \le 2573 K)—4.7016 (Debye frequency)—240 atoms, DFTBiii^{\mathrm{iii}} Lattice vibration[16]
5.033.78——72 atoms, 450 eV, HSE06[17]
3.69–3.573.47–3.46517.75–628.582×10−192\times10^{-19}–7×10−187\times10^{-18}72 atoms, 450 eV, HSE06 Lattice expansion Lattice vibration Electron excitation Band-edge shiftThis work

Table S3. Comparison of defect formation energy, activation enthalpy, attempt frequency, and diffusion coefficient of VAlV_{\mathrm{Al}} hopping in Al bulk, vacancy-assisted FeAl diffusion in Al bulk, and VCV_{\mathrm{C}} hopping in 4H-SiC between this work and theoretical literature.

Five-frequency model for FeAl diffusion in aluminum bulk

Vacancy-assisted solute diffusion in FCC bulk is typically described by the five-vacancy-jump-frequency model,[18] which involves five processes as indicated in Figure S6 and quantified by Eqs. (10)–(13). Specifically, ω0\omega_0 is the jump frequency of a vacancy in pure bulk, ω1\omega_1 the jump frequency of a vacancy between nearest-neighbor sites of a solute, ω2\omega_2 the jump frequency of the solute-vacancy exchange process, ω3\omega_3 the jump frequency of a vacancy from nearest-neighbor sites of solute to non-nearest-neighbor sites, and ω4\omega_4 the jump frequency of the reverse jump of process 3. For the diffusion of FeAl in aluminum bulk, because the hopping barrier of process ω1\omega_1 and ω2\omega_2 is around 0.38 and 0.74 eV, respectively, ω2/ω1\omega_2/\omega_1 is close to zero (2.4×10−42.4 \times10^{-4}–9.8×10−39.8 \times10^{-3}) in our examined temperature of 500–900 K. Therefore, f2f_2 in Eq. (12) can be approximated as 1, and the diffusion coefficient in Eq. (10) can be solely determined by ω2\omega_2, ω3\omega_3, ω4\omega_4, and GfG_f, as expressed in Eq. (8).

Five-vacancy-jump-frequency model for FCC lattice

Figure S6. Five-vacancy-jump-frequency model for FCC lattice.

D=f2ω2ω4f0ω0ω3(Γf0a2e−GfkBTω0)(10)D = \frac{f_2 \omega_2 \omega_4}{f_0 \omega_0 \omega_3}\left(\Gamma f_0 a^2 e^{-\frac{G_f}{k_B T}}\omega_0\right) \tag*{(10)}
ωi=ν0,ie−Ebi(T)kBT(11)\omega_i = \nu_{0,i} e^{-\frac{E_{bi}(T)}{k_B T}} \tag*{(11)}
f2=1+72F(ω4ω0)×(ω3ω1)1+72F(ω4ω0)×(ω3ω1)+(ω2ω1)(12)f_2 = \frac{1+\frac{7}{2}F\left(\frac{\omega_4}{\omega_0}\right)\times\left(\frac{\omega_3}{\omega_1}\right)}{1+\frac{7}{2}F\left(\frac{\omega_4}{\omega_0}\right)\times\left(\frac{\omega_3}{\omega_1}\right)+\left(\frac{\omega_2}{\omega_1}\right)} \tag*{(12)}
F(x)=1−10x4+180.5x3+927x2+1341x7(2x4+40.2x3+254x2+597x+436)(13)F(x) = 1-\frac{10x^4+180.5x^3+927x^2+1341x}{7(2x^4+40.2x^3+254x^2+597x+436)} \tag*{(13)}

Here, GfG_f is the formation energy of VAlV_{\mathrm{Al}} and ν0,i\nu_{0,i} is the ithi^{\mathrm{th}} process’ attempt frequency calculated using Eq. 4b in the main text.

D=ω2ω4ω3(Γa2e−GfkBT)(14)D = \frac{\omega_2 \omega_4}{\omega_3}\left(\Gamma a^2 e^{-\frac{G_f}{k_B T}}\right) \tag*{(14)}

Charge density of VBM and CBM in 4H-SiC bulk

Figure S7-Figure S7) shows the charge density of CBM and VBM at 0 K. The CBM majorly locates in the hollow region in the crystal, but VBM binds locally around C atoms. Such spatial distribution does not change radically in the MD simulations at high temperatures, as shown in Figure S7-Figure S7). Therefore, the loose (tight) spatial distribution of CBM (VBM) qualitatively explains the fact that the CBM is much more sensitive to the lattice change than VBM as temperature increases.

Charge density of CBM and VBM of 4H-SiC bulk at 0 K, and examples of charge density of CBM and VBM for 4H-SiC at 2473 K

Figure S7. Charge density of (a) CBM and (b) VBM of 4H-SiC bulk at 0 K; examples of charge density of (c) CBM and (d) VBM for 4H-SiC at 2473 K.

DOS and intrinsic Fermi level of 4H-SiC bulk at 2473 K

Figure S8 compares between the average DOS of 4H-SiC bulk obtained from AIMD structures at 2473 K and the DOS of 0 K with a rigid shift of the conduction bands by -1.31 eV to recover the band gap reduction. Because of the lattice vibration, the average DOS at 2473 K is smoother than that of 0 K. The intrinsic Fermi level calculated based on the average DOS of 2473 K and the shifted DOS of 0 K is 1.029 and 1.026 eV above the VBM, respectively. Given such negligible difference and the high computational cost of average DOS from AIMD structures, the shifted DOS of 0 K is more favorable here.

DOS of 4H-SiC bulk at 2473 K

Figure S8. DOS of (a) the 7000{sup}th, 7400{sup}th, 7800{sup}th, 8200{sup}th, 8600{sup}th, and 9000{sup}th step in AIMD simulation at 2473 K, (b) average DOS of the sampled AIMD structures and DOS of 0 K with the conduction bands shifted by -1.31 eV according to Figure 4c.

Defect formation energy of VCV_{\mathrm{C}} in 4H-SiC bulk at 0 K

Figure S9 shows the defect formation energy of VCV_{\mathrm{C}} in 4H-SiC at 0 K without any temperature effects. The Fermi level is set to be at the mid-gap, where the charge state of VCV_{\mathrm{C}} is 2+2+ in the initial state and 0 in the transition state in intrinsic 4H-SiC.

Defect formation energy of the initial and transition states during $V_{\mathrm{C}}$ hopping in 4H-SiC

Figure S9. Defect formation energy of the initial state (IS) and transition state (TS) during the VCV_{\mathrm{C}} hopping in 4H-SiC at 0 K without any temperature effects.

Effects of LO-TO splitting on the phonon DOS, attempt frequency, and diffusivity of VC2+V_{\mathrm{C}}^{2+} in 4H-SiC bulk at 2473 K

Figure S10-Figure S10) compares the phonon DOS of VC2+V_{\mathrm{C}}^{2+} in 4H-SiC bulk in the initial and transition states at 2473 K with and without the LO-TO splitting. The LO-TO splitting brings in an increase of attempt frequency by ∼12\sim12 THz or ∼2%\sim2\% (Figure S10) and an increase of diffusivity by ∼2%\sim2\% (Figure S10).

Comparison of phonon DOS, attempt frequency, and diffusivity of V_C^{2+} with and without LO-TO splitting

Figure S10. Comparison of phonon DOS of VC2+V_{\mathrm{C}}^{2+} in 4H-SiC at 2473 K for the (a) initial state and (b) transition state with and without LO-TO splitting; comparison of the (c) attempt frequency and (d) diffusivity of VC2+V_{\mathrm{C}}^{2+} with and without LO-TO splitting.

References

  1. [1]A. J. C. Wilson, "The thermal expansion of aluminium from 0° to 650 °C," Proc. Phys. Sci. 53, 235-244 (1941).DOI
  2. [2]M. Stockmeier, R. Muller, S. A. Sakwe, P. J. Wellmann and A. Magerl, "On the lattice parameters of silicon carbide," J. Appl. Phys. 105, 033511 (2009).DOI
  3. [3]M. Beyeler and Y. Adda, "Détermination des volumes d'activation pour la diffusion des atomes dans l'or, le cuivre et l'aluminium," J. Phys. 29, 345-352 (1968).
  4. [4]S. Dais, R. Messer and A. Seeger, "Nuclear-magnetic-resonance study of self-diffusion in aluminium," Mater. Sci. Forum 15-18, 419-424 (1987).DOI
  5. [5]T. S. Lundy and J. F. Murdock, "Diffusion of Al²⁶ and Mn⁵⁴ in aluminum," J. Appl. Phys. 33, 1671-1673 (1962).DOI
  6. [6]G. Makov and M. C. Payne, "Periodic Boundary-Conditions in Ab-Initio Calculations," Phys. Rev. B 51, 4014-4022 (1995).pubmed.ncbi.nlm.nih.gov/9979237
  7. [7]P. Mohn, C. Persson, P. Blaha, K. Schwarz, P. Novak and H. Eschrig, "Correlation induced paramagnetic ground state in FeAl," Phys. Rev. Lett. 87, 196401 (2001).
  8. [8]L. Wang, T. Maxisch and G. Ceder, "Oxidation energies of transition metal oxides within the GGA+U framework," Phys. Rev. B 73, 195107 (2006).
  9. [9]H. Wu, T. Mayeshiba and D. Morgan, "High-throughput ab-initio dilute solute diffusion database," Sci Data 3, 160054 (2016).DOI
  10. [10]M. Cococcioni and S. de Gironcoli, "Linear response approach to the calculation of the effective interaction parameters in the LDA+U method," Phys. Rev. B 71, 035105 (2005).DOI
  11. [11]S. Falletta and A. Pasquarello, "Hubbard U through polaronic defect states," npj Comput. Mater. 8, 263 (2022).arxiv.org/abs/2209.11341
  12. [12]K. Carling, G. Wahnstrom, T. R. Mattsson, A. E. Mattsson, N. Sandberg and G. Grimvall, "Vacancies in metals: from first-principles calculations to experimental data," Phys. Rev. Lett. 85, 3862-3865 (2000).pubmed.ncbi.nlm.nih.gov/11041946
  13. [13]B. Grabowski, L. Ismer, T. Hickel and J. Neugebauer, "Ab initio up to the melting point: Anharmonicity and vacancies in aluminum," Phys. Rev. B 79, 134106 (2009).DOI
  14. [14]N. Sandberg, B. Magyari-Kope and T. R. Mattsson, "Self-diffusion rates in Al from combined first-principles and model-potential calculations," Phys. Rev. Lett. 89, 065901 (2002).pubmed.ncbi.nlm.nih.gov/12190597
  15. [15]M. Mantina, Y. Wang, R. Arroyave, L. Q. Chen, Z. K. Liu and C. Wolverton, "First-Principles Calculation of Self-Diffusion Coefficients," Phys. Rev. Lett. 100, 215901 (2008).
  16. [16]E. Rauls, T. Frauenheim, A. Gali and P. Deak, "Theoretical study of vacancy diffusion and vacancy-assisted clustering of antisites in SiC," Phys. Rev. B 68, 155208 (2003).DOI
  17. [17]G. Luo, T. F. Kuech and D. Morgan, "Transition state redox during dynamical processes in semiconductors and insulators," NPG Asia Mater. 10, 45-51 (2018).DOI
  18. [18]R. E. Howard and J. R. Manning, "Kinetics of solute-enhanced diffusion in dilute face-centered-cubic alloys," Phys. Rev. 154, 561 (1967).

Paper details

vlnc:W_xmaeq4fn
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents