betaFeedback

WorksPhysics and Astronomy

Absence of Long-Range Magnetic Ordering in a Trirutile High-Entropy Oxide (Mn0.2_{0.2}Fe0.2_{0.2}Co0.2_{0.2}Ni0.2_{0.2}Cu0.2_{0.2})Ta1.92_{1.92}O6−δ_{6-δ}

Abstract

Functionalities of solid-state materials are usually considered to be dependent on their crystal structures. The limited structural types observed in the emerged high-entropy oxides put constraints on exploration of their physical properties and potential applications. Herein, we synthesized the first high-entropy oxide in a trirutile structure, (Mn0.2_{0.2}Fe0.2_{0.2}Co0.2_{0.2}Ni0.2_{0.2}Cu0.2_{0.2})Ta1.92_{1.92}O6−δ_{6-δ}, and investigated its magnetism. The phase purity and high-entropy nature were confirmed by powder X-ray diffraction and energy-dispersive spectroscopy, respectively. X-ray photoelectron spectroscopy indicated divalent Mn, Co, Ni and Cu along with trivalent Fe. Magnetic properties measurements showed antiferromagnetic coupling and potential short-range magnetic ordering below ~ 4 K. The temperature-dependent heat capacity data measured under zero and high magnetic field confirmed the lack of long-range magnetic ordering and a possible low-temperature phonon excitation. The discovery of the first trirutile high-entropy oxide opens a new way for studying the relationship between the highly disordered atomic arrangement and their magnetic interaction. Furthermore, it provides a new direction for exploring functionalities of high-entropy oxides.

Introduction

High-entropy oxides (HEOs) are a type of material where five or more elements are randomly distributed in equiatomic stoichiometry on the same atomic site. Vast applications such as catalysis[1] and reversible energy storage2 were found for HEOs. Better mechanical properties and resistance to oxidation/corrosion were also observed for HEOs3,4. In addition, magnetic insulating HEOs were reported due to their potential application in the next-generation memory and spintronic devices5. Since Rost et. al. discovered the first HEO in rocksalt structure6, there have been great efforts to expand the structural types of HEOs. To date, ten major crystal structures were found for HEOs: bixbyite (A2O3\mathrm{A}_2\mathrm{O}_3)7, delafossite (ABO2\mathrm{ABO}_2)8, fluorite (AO2\mathrm{AO}_2)9, magnetoplumbite (AB12O19\mathrm{AB}_{12}\mathrm{O}_{19})10, mullite-type (A2B4O10\mathrm{A}_2\mathrm{B}_4\mathrm{O}_{10})11, perovskite (ABO3\mathrm{ABO}_3)12, pyrochlore (A2B2O7\mathrm{A}_2\mathrm{B}_2\mathrm{O}_7)13,14, rocksalt (AO\mathrm{AO})6, Ruddlesden-Popper phase (An+1BnO3n+1\mathrm{A}_{n+1}\mathrm{B}_n\mathrm{O}_{3n+1})15 and spinel (AB2O4\mathrm{AB}_2\mathrm{O}_4)16 where A and B are cations. However, many structural types remain obscure, which significantly limits the manipulation and exploration of HEOs’ properties. Furthermore, research surrounding their magnetic properties is only recently studied17. Upon investigation, HEOs can possess complicated magnetic properties due to the disordering of multiple transition metals, e.g., the spin-glass states in perovskite HEOs18 and tunable magnetism in spinel HEOs16. Considering the importance of crystal structure in determining physical properties, expanding the structural families of HEOs is crucial for exploring their functionalities and potential applications.

Herein, we report the first trirutile HEO, (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}, belonging to space group P42/mnmP4_2/mnm (no. 136) evidenced by X-ray diffraction (XRD) and energy-dispersive spectroscopy (EDS). While there were reports of rutile HEOs19, the trirutile structure remains unfounded. Trirutile i.e. AB2O6\mathrm{AB}_2\mathrm{O}_6, is a derivative of the rutile structure i.e. AO2\mathrm{AO}_2, wherein an additional element disrupts the repeatability of the rutile structure such that a 1×1×31 \times1 \times3 superlattice is formed. NiTa2O6\mathrm{NiTa}_2\mathrm{O}_620, CuTa2O6\mathrm{CuTa}_2\mathrm{O}_621 and CoTa2O6\mathrm{CoTa}_2\mathrm{O}_622 have all been studied for their antiferromagnetic properties as trirutile oxides and we employed CoTa2O6\mathrm{CoTa}_2\mathrm{O}_6 as the parent compound, which was reported to be antiferromagnetically ordered below TN∼6.6 K\mathrm{T}_\mathrm{N} \sim6.6\ \mathrm{K}22. However, when doped with Mg, i.e., Co1−xMgxTa2O6\mathrm{Co}_{1-x}\mathrm{Mg}_x\mathrm{Ta}_2\mathrm{O}_6, the antiferromagnetic ground state is quenched at x=10%x=10\% while a short-range ferromagnetic correlation can be found in all series of compositions23. Considering that the theoretical calculations suggest the ferromagnetic ground state23 competing ferromagnetic and antiferromagnetic interactions must exist in CoTa2O6\mathrm{CoTa}_2\mathrm{O}_6. Our investigation on the physical properties of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} suggests short-range antiferromagnetic interaction resulting from the highly disordered transition-metal site. Therefore, the trirutile CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6} provides a good platform for investigating the interplay between magnetism and the crystallographic disorder on the Co site, with further possibilities to extend the scope of physical properties in trirutile HEOs.

Experimental Details

Synthesis of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}

(Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} was prepared by mixing CoO powder (99.995%, Thermo Scientific), MnO powder (99.99%, Thermo Scientific), CuO powder (99.7%, ∼\sim200 mesh, Alfa Aesar), NiO powder (99.998%, Thermo Scientific), Fe2O3\mathrm{Fe}_{2}\mathrm{O}_{3} powder (99.9%, Thermo Scientific), and Ta2O5\mathrm{Ta}_{2}\mathrm{O}_{5} powder (99.5% Thermo Scientific), and by placing the 0.2 : 0.2 : 0.2 : 0.2 : 0.1 : 0.96 mixture into an alumina crucible. The crucible was covered with a small alumina lid, placed into a larger crucible, and then surrounded with activated charcoal (untreated, ≤\leq5 mm, Sigma-Aldrich). This assembly was then placed into a microwave (1000 W, Model 40GR47) in the air, equipped with firebricks for further insulation and microwaved for a total of 30 minutes at 5-minute intervals with grinding in between. The sample was then pressed into a pellet and placed in a furnace preheated to 1250 °C in air for 1 hr, then air quenched. The resulting sample is a homogeneous brown chunk that is stable in air. A high purity phase could not be realized without a 4% deficiency in Ta2O5\mathrm{Ta}_{2}\mathrm{O}_{5} or microwaving, the reasons for which are detailed later.

Phase Identification:

(Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} was crushed into a powder and prepared for powder X-ray diffraction (XRD). A Bruker D2 PHASER was used with Cu Kα\alpha radiation (λ=1.54060\lambda= 1.54060 Å, Ge monochromator). The Bragg angle measured was from 5 to 100 ° at a rate of 1.7 °/min with a step of 0.012 °. Rietveld fitting in FULLPROF was employed to analyze the crystal structure and test the phase purity of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}24.

Physical Properties Measurements:

Magnetic Properties were measured in a Quantum Design Dynacool physical properties measurement system (PPMS) (1.8- 300 K, 0-9 T) equipped with ACMS II with both DC and AC magnetic fields available as well as a vibrating-sample magnetometer (VSM). Heat capacity was measured in the PPMS from 1.9 K to 37 K. Resistivity measurements were conducted in the PPMS from 310 K to 350 K using the four-probe method with platinum wires attached to the representative sample using silver epoxy.

Scanning Electron Microscopy (SEM) with Energy-Dispersive Spectroscopy (EDS):

Compositional analysis was performed via scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS). A Ziess Sigma 500 VP SEM with Oxford Aztec X-EDS was used with an electron beam energy of 20 kV.

Results and Discussion

Crystal structure and compositional analysis: Powder XRD pattern of the air-quenched sample from 5 to 100° is shown in Figure 1(a). The pattern was fitted via Rietveld method by using the crystal structure of reported CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6}25. The fitting parameters, i.e., Rp=3.62%R_{\mathrm{p}} = 3.62\%, Rwp=4.63%R_{\mathrm{wp}} = 4.63\%, Rexp=4.02%R_{\mathrm{exp}} = 4.02\% and χ2=1.32\chi^{2} = 1.32, showed good match between the trirutile CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6} and the proposed HEO (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. No prominent secondary phase was found, indicating that (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} crystallizes in the same space group as CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6}, i.e., P42/mnmP4_{2}/mnm with a high purity. The refined lattice parameters of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} are a=4.73179(1)a = 4.73179(1) Å, c=9.20395(3)c = 9.20395(3) Å, which creates a slightly smaller unit cell than CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6} (a=4.73580a = 4.73580 Å, c=9.17080c = 9.17080 Å) with smaller tetragonality, i.e., smaller c/ac/a ratio. The fitted atomic coordinates are shown in Table S1 in the supporting information (SI), which further confirms the trirutile structure for (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. The obtained crystal structure is shown in Figure 1(b) & Figure 1(c). Edge-shared M@O6\mathrm{M@O}_{6} and Ta@O6\mathrm{Ta@O}_{6} octahedra stack along the cc axis and are connected with each other in a corner-sharing manner. The M@O6\mathrm{M@O}_{6} layers with high-entropy site consisting of 3d3d transition metals within abab plane are separated by Ta@O6\mathrm{Ta@O}_{6} layers.

Powder XRD pattern, trirutile structure, crystal structure, and SEM-EDS elemental mapping

Figure 1. (a) Powder XRD pattern of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. The observed pattern is shown by the red line with dots while the black line represents the calculated pattern. The difference between the observed and calculated pattern is shown in blue. Bragg peaks positions of CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6} are visualized with orange vertical bars. (b) (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} trirutile structure viewing from the bb axis. Here, “M” stands for the 3d3d transition metals in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. (c) (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} viewing from the cc axis with Ta@O6\mathrm{Ta}@\mathrm{O}_{6} (cyan) and M@O6\mathrm{M}@\mathrm{O}_{6} (yellow) octahedra (d) SEM-EDS elemental mapping results of Co, Cu, Fe, Mn, Ni, Ta, and O on a ∼0.11\sim0.11-mm2^{2} area of pellet sample.

xxyyzz
M1000
Ta1000.3317 (1)
O10.2896 (9)0.2896 (9)0
O20.3007 (6)0.3007 (6)0.3337 (6)

Table S1. The atomic sites of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} were determined via Rietveld refinement. (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} is in space group P42/mnmP4_{2}/mnm (no. 136) with parameters a=4.73179a = 4.73179 (1) Å and c=9.20395c = 9.20395 (3) Å. M stands for 3d transition metals.

In order to confirm the high-entropy nature of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}, SEM-EDS analysis was performed. In two distinct regions of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}, elemental maps were collected and can be seen in Figure 1(d), for which the results are shown in Table S2 in the supporting information. The average chemical formula was found to be Mn0.19(1)Fe0.20(1)Co0.18(1)Ni0.20(1)Cu0.20(2)Ta1.92(1)O6−δ\mathrm{Mn}_{0.19(1)}\mathrm{Fe}_{0.20(1)}\mathrm{Co}_{0.18(1)}\mathrm{Ni}_{0.20(1)}\mathrm{Cu}_{0.20(2)}\mathrm{Ta}_{1.92(1)}\mathrm{O}_{6-\delta}, displaying near equiatomic ratios of each 3d3d transition metal. Given that each 3d3d transition metal M can form a stable phase in MTa2O6\mathrm{MTa}_{2}\mathrm{O}_{6}21,22,26,27, our material is not an entropy-stabilized material.6 Meanwhile, we note that there is a deficiency in oxygen based on EDS and further examined in the magnetic superexchange pathway section. Since (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} is an insulator (as discussed later), charging effects may affect the EDS results.28 When considering this, our results are within the error of loading composition. To study the surface composition of our sample, XPS was performed. Three points of interest were analyzed to determine the surface concentration of the 3d3d transition metals to be 14(5)% Mn, 35(4)% Fe, 27(8)% Co, 10(2)% Ni, and 14(10)% Cu. As exemplified by the high levels of deviation as well as the non-equiatomic ratios, there are surface inhomogeneities in the sample. More analysis of XPS is provided in the SI. XPS has a penetration depth of ∼10\sim10 nm29, while EDS has a penetration depth of around 2 microns at 20keV30. Therefore, the surface inhomogeneities will less likely affect the bulk properties. Since our studies focus on the bulk properties of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}, the EDS determined chemical composition will reflect more precisely the bulk composition. Therefore, all subsequent calculations were performed based on the loading composition, i.e., (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. Further information about XPS results can be found in the Supporting Information.

SpectraMnFeCoNiCuTa
Map 12.182.332.132.272.4622.07
Map 22.302.312.092.332.1622.18
Average2.24 (8)2.32 (2)2.11 (2)2.30 (4)2.31 (21)22.13 (7)
Normalized to Ta as 1.920.19 (1)0.20 (1)0.18 (1)0.20 (1)0.20 (2)1.92 (1)
Loading Composition0.20.20.20.20.21.92

Table S2. EDS results of MTa1.92O6\mathrm{MTa}_{1.92}\mathrm{O}_{6} for two different areas of the sample. Data was normalized to Ta and compared to the loading composition.

Short-range antiferromagnetic ordering in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}:

(Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} was measured for the temperature dependence of magnetic susceptibility from 1.8 to 300 K under an external magnetic field of 0.1 T in a zero-field cooling mode, as shown in Figure 2. Paramagnetic behavior was seen under high temperature while a broad peak can be observed at ~ 4 K, as discussed later. Curie-Weiss (CW) fitting was performed from 150 to 275 K according to the modified CW law:

Magnetic susceptibility and inverse magnetic susceptibility versus temperature

Figure 2. Magnetic susceptibility minus χ0\chi_0 (left red axis) and inverse of magnetic susceptibility minus χ0\chi_0 (right blue axis) of (Mn0.2_{0.2}Fe0.2_{0.2}Co0.2_{0.2}Ni0.2_{0.2}Cu0.2_{0.2})Ta1.92_{1.92}O6−δ_{6-\delta} measured under an external magnetic field of 0.1 T with respect to temperature. The cyan line represents the Curie-Weiss fitting. The inset zooms in on the difference between the inverse of magnetic susceptibility minus χ0\chi_0 with respect to temperature under zero-field cooling (red line) and field cooling (purple line) also at an external magnetic field of 0.1 T.

χ=CT−θCW+χ0\chi= \frac{C}{T-\theta_{\mathrm{CW}}}+\chi_0

where χ\chi is the magnetic susceptibility, C is the Curie constant independent of temperature and related to the effective moment (μeff\mu_{\mathrm{eff}}), θCW\theta_{\mathrm{CW}} is the CW temperature and χ0\chi_0 is a constant independent of temperature and related to the core diamagnetism and temperature-independent paramagnetic contributions such as Pauli paramagnetism. The χ0\chi_0 parameter was added to CW fitting since a slightly positive curvature was noted at ~ 250K and was fitted to be 0.00109(1) emu/Oe/mol. The resulted θCW\theta_{\mathrm{CW}} is -19.6 (2) K, indicating antiferromagnetic (AFM) spin-spin coupling within the

fitted temperature region. Therefore, the slight deviation from CW behavior at ∼58\sim58 K might originate from the onset of AFM coupling, as seen in Figure S1 in the SI. The resulting θCW\theta_{\mathrm{CW}} is enhanced in comparison to the parent Mn (-4.2 K)26, Fe (-8.11(5) K)27, Co (-6.63(5) K)22, Ni (-10.3(2) K)22 and Cu (-1.5(2) K)21 tantalate compounds.

Based on μeff\mu_{\mathrm{eff}} (spin-only) =n(n+2)= \sqrt{n(n+2)} where nn is the number of unpaired electrons, the spin-only moment for all 3dd transition metal ions except for Co2+\mathrm{Co}^{2+} in high-spin octahedral crystal field in our material are as follows: Mn2+\mathrm{Mn}^{2+} (∼5.92\sim5.92 μB\mu_{\mathrm{B}}), Fe3+\mathrm{Fe}^{3+} (∼5.92\sim5.92 μB\mu_{\mathrm{B}}), Ni2+\mathrm{Ni}^{2+} (∼2.83\sim2.83 μB\mu_{\mathrm{B}}), and Cu2+\mathrm{Cu}^{2+} (∼1.73\sim1.73 μB\mu_{\mathrm{B}}). Since Co2+\mathrm{Co}^{2+} ions exhibit large single-ion anisotropy, we chose to use the effective moment reported for CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6}, 4.9(2) μB\mu_{\mathrm{B}} for Co2+\mathrm{Co}^{2+} instead.23 The μeff\mu_{\mathrm{eff}} when considering equal contributions from each 3dd transition metal, averages to ∼4.26\sim4.26 μB\mu_{\mathrm{B}} which is consistent with the μeff\mu_{\mathrm{eff}} from CW fitting determined via μeff=8C\mu_{\mathrm{eff}} = \sqrt{8C} to be 4.336 (5) μB\mu_{\mathrm{B}}/f.u. The larger fitted μeff\mu_{\mathrm{eff}} might be due to the unaccounted contributions from orbital angular momentum.

As shown in Figure 2 inset, the χ\chi vs T curve features a broad downward parabola shape at ∼4\sim4 K when under zero-field cooling (ZFC), unlike the more linear shape that is realized under field-cooling (FC). Therefore, we performed the temperature-dependent AC magnetic susceptibility measurements with a DC field of 100 Oe and an AC field of 10 Oe under different frequencies to confirm the existence of spin-glass state. As shown in Figure S2 in the SI, no frequency-dependent behavior can be seen for the AC susceptibility under 936 Hz, 1635 Hz and 1858 Hz from 2 K to 10 K, which excludes conventional spin-glass state in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. Meanwhile, the DC magnetic susceptibility under FC protocol does not reach a plateau in our material, which further confirms the lack of conventional spin-glass state. The divergence between the ZFC and FC curves below ∼4\sim4 K normally originates from spin freezing.31,32 Therefore, the broad peak observed in Figure 2 might originate from short range antiferromagnetic ordering, which will be further discussed later along with the heat capacity results. Moreover, similar behavior can be seen in Mg-doped CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6} where short-range magnetic ordering was observed when the Mg concentration is above ∼10%\sim10\%.23

The field-dependence of magnetization, as shown in Figure 3, illustrates that at 2, 10, and 300 K, (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} does not become saturated from up to 9 T. A slightly bent feature can be seen under 2 K, which is typical for paramagnetic state. In addition, no coercive field is observed, as can be seen in Figure S3 in the SI, which can be the indicative of the absence of a long-range ordered ferromagnetic component.

Field-dependent magnetization curves at 2, 10, and 300 K

Figure 3. Field-dependent magnetization from 0-9 T at 2, 10, and 300 K, in blue, red and violet, respectively.

Peak fitting plots for Mn, Fe, Co, Ni, and Cu

Figure S3. Peak fitting of Mn, Fe, Co, Ni, and Cu in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} in area 1. B.E. stands for binding energy. Blue plus signs mark satellite peaks wile red asterisks mark Auger peaks.

Heat Capacity: The temperature-dependent heat capacity of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} was measured from 2 to 35 K. No indication of long-range magnetic ordering, i.e., a λ\lambda-anomaly in heat capacity curve, can be seen, as shown in Figure 4(a). While a broad feature appears at ∼4\sim4 K in Figure 4(a), Figure 4(b) plots the Ctotal/TC_{\mathrm{total}}/T vs TT curve and the broad peak is shown at ∼4\sim4 K. The total heat capacity of a magnetic material can be treated as the sum of electronic, phononic, and magnonic contribution where Ctotal=Cel+Cph+CmagC_{\mathrm{total}} = C_{\mathrm{el}} + C_{\mathrm{ph}} + C_{\mathrm{mag}}. As shown by resistivity in Figure S4 in the supporting information, (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} exhibits insulating behavior, thus there are no electronic contributions to heat capacity, i.e., Ctotal=Cph+CmagC_{\mathrm{total}} = C_{\mathrm{ph}} + C_{\mathrm{mag}}. As an estimate, Cph=βT3C_{\mathrm{ph}} = \beta T^3 according to the Debye formula where β\beta is the vibrational contribution coefficient. However, just a T3T^3 term could not lead to a good fitting. This could be due to unaccounted high-frequency phononic contributions to heat capacity, as the Debye formula is only an estimate. Herein, T5T^5, T7T^7, T9T^9, and T11T^{11} terms were added to obtain a reasonable fitting so that a polynomial fit was employed:

Heat capacity and magnetic entropy plots

Figure 4. (a). CtotalC_{\mathrm{total}} is shown in magenta as a function of temperature. (b) Ctotal/TC_{\mathrm{total}}/T is shown in blue filled circles while Cmag/TC_{\mathrm{mag}}/T is shown in blue open circles. The fitted CphC_{\mathrm{ph}} is graphed in red. These three curves correspond to the left blue axis. Rln⁡2R\ln2 is shown by the orange dashed line and ΔSmag\Delta S_{\mathrm{mag}} is the solid orange line; both lines correspond to the right orange axis.

Cph/T=β1T2+β2T4+β3T6+β4T8+β5T10C_{\mathrm{ph}}/T = \beta_1 T^2 + \beta_2 T^4 + \beta_3 T^6 + \beta_4 T^8 + \beta_5 T^{10}

where β1\beta_1, β2\beta_2, β3\beta_3, β4\beta_4, and β5\beta_5 are constants and were fitted to 0.00311(9) J/mol/K4^4, −8.6(5)×10−6-8.6(5) \times10^{-6} J/mol/K6^6, 1.2(1)×10−81.2(1) \times10^{-8} J/mol/K8^8, −7.7(8)×10−12-7.7(8) \times10^{-12} J/mol/K10^{10}, and 2.0(2)×10−152.0(2) \times10^{-15} J/mol/K12^{12}. Therefore, by subtracting the phononic contribution from Ctotal/TC_{\mathrm{total}}/T, pure Cmag/TC_{\mathrm{mag}}/T is plotted in Figure 4(b) as blue open circles. By integrating Cmag/TC_{\mathrm{mag}}/T vs TT curve, the change in magnetic entropy, ΔSmag\Delta S_{\mathrm{mag}}, is obtained. ΔSmag\Delta S_{\mathrm{mag}} is usually determined by the spin multiplicity in a magnetic system where contributions from orbital angular momentum can be ignored by ΔSmag=Rln⁡(2S+1)\Delta S_{\mathrm{mag}} = R\ln(2S+1) where RR is the gas constant. Here, ΔSmag\Delta S_{\mathrm{mag}} does not exceed Rln⁡2R\ln2, which is the magnetic entropy change for a S=12S = \frac{1}{2} system. Because the average spin state of the 3d3d transition metals appearing in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}, i.e., Mn2+\mathrm{Mn}^{2+} (S=5/2S = 5/2), Fe3+\mathrm{Fe}^{3+} (S=5/2S = 5/2), Co2+\mathrm{Co}^{2+} (S=3/2S = 3/2), Ni2+\mathrm{Ni}^{2+} (S=1S = 1), and Cu2+\mathrm{Cu}^{2+} (S=1/2S = 1/2), must be larger than S=3/2S = 3/2. Therefore, the observed ΔSmag\Delta S_{\mathrm{mag}} is obviously smaller than Rln⁡4R\ln4, indicating the absence of long-range magnetic ordering within the measured temperature range in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. Heat capacity of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} was also measured under an external magnetic field, as shown in Figure S5 in the supporting information; no shift is observed for peak position. The field-independent behavior suggests that such anomaly below ∼5\sim5 K is not spin-related, instead, it can be due to the phononic excitation.

Magnetic superexchange interaction and possible origin of short-range magnetic ordering

Based on the crystal structure of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}, two possible magnetic superexchange pathways can be proposed, as illustrated in Figure 5, while the other pathways are related to them by symmetries. These superexchange pathways are based on the Goodenough-Kanamori rule33,34 and the atomic orbitals of M2+/3+\mathrm{M}^{2+/3+} near the Fermi energy are determined by the semi-empirical extended-Hückel-tight-binding (EHTB) methods and CAESAR packages, as described in the SI. The calculation was only conducted on the parent compound, CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6}, due to the complexities of the high-entropy (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}. However, the symmetries of molecular orbitals in CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6} can be well extended to (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} regardless of addition or removal of valence electrons of 3d3d transition metal ions. Therefore, the analysis of molecular orbitals in the high-entropy compound can be conducted based on the highest-occupied molecular orbital in CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6} by varying the number of electrons.

Two different magnetic superexchange pathways

Figure 5. The two different magnetic superexchange pathways in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} between transition metal ions. M2+/3+\mathrm{M}^{2+/3+} stand for transition metal ions. The relative vertical distance between atomic orbitals stands for the relative geometry of ions. The dashed orange lines involve the pair of electrons on difference p orbitals of oxygen ions that stabilize the superexchange pathways by inclusion of exchange energy.

The first superexchange pathway is shown in Figure 5(a) where two M@O6\mathrm{M}@\mathrm{O}_{6} octahedra are connected by Ta@O6\mathrm{Ta}@\mathrm{O}_{6} octahedron via an axial manner. In this case, half-filled dxz\mathrm{d}_{xz} orbital of M2+/3+\mathrm{M}^{2+/3+}, fully-filled px\mathrm{p}_{x} and pz\mathrm{p}_{z} orbitals of O2−\mathrm{O}^{2-} and empty dz2\mathrm{d}_{z}^{2} orbital of Ta5+\mathrm{Ta}^{5+} are present. The two M2+/3+\mathrm{M}^{2+/3+} ions on the opposite sides show antiferromagnetic coupling due to the following reasons: 1. due to the virtual electron hopping represented by the arrows, a pair of spins with opposite spin directions from oxygen pz\mathrm{p}_{z} orbitals can populate the empty dz2\mathrm{d}_{z}^{2} orbital of Ta5+\mathrm{Ta}^{5+}, which provides a more stable ground state; 2. the exchange energies between the spins with the same direction on px\mathrm{p}_{x} and pz\mathrm{p}_{z} orbitals of O2−\mathrm{O}^{2-} stabilize the system as well, as indicated by the orange dashed lines in Figure 5; 3. virtual electron hopping can also occur between the px\mathrm{p}_{x} orbitals of O2−\mathrm{O}^{2-} and the half-filled dxz\mathrm{d}_{xz} orbital of M2+/3+\mathrm{M}^{2+/3+}, which leads to a stable singlet state. The superexchange interaction depicted results in

the antiferromagnetic coupling between the M2+/3+\mathrm{M}^{2+/3+} ions. Similar reasons and superexchange pattern can be found in the second pathway, shown in Figure 5(b), while the involved atomic orbitals are now the half-filled dz2d_z^2 orbital of M2+/3+\mathrm{M}^{2+/3+}, fully-filled pxp_x and pyp_y orbitals of O2−\mathrm{O}^{2-} and empty dxyd_{xy} orbital of Ta5+\mathrm{Ta}^{5+}. In both cases, antiferromagnetic coupling between M ions is dominant.

With the analysis above, we can speculate three possible reasons of the short-range magnetic ordering observed in magnetic properties measurements:

  • The existence of Ni2+\mathrm{Ni}^{2+} and Cu2+\mathrm{Cu}^{2+} leads to the lack of half-filled dxzd_{xz} orbitals, which disables the scenario in Figure 5(a) where a half-filled dxzd_{xz} orbital of M2+/3+\mathrm{M}^{2+/3+} is necessary. Subsequently, the corresponding superexchange pathway is not functional due to the lack of electron hopping and, thus, magnetic coupling is absent. Meanwhile, all the M2+/3+\mathrm{M}^{2+/3+} ions possess a half-filled dz2d_z^2 orbital, which allows the superexchange interaction in Figure 5(b). Therefore, with part of the superexchange pathways disabled, long-range magnetic ordering does not exist in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}.

  • Due to the existence of Fe3+\mathrm{Fe}^{3+}, in order to maintain charge neutrality, possible removal of cations can take place as a result of ionic charge compensation mechanism. Therefore, part of the M2+\mathrm{M}^{2+} or Ta5+\mathrm{Ta}^{5+} sites may be vacant, leading to the interruption of the superexchange pathways and the absence of long-range magnetic ordering. The Ta5+\mathrm{Ta}^{5+} vacancy is seen in the inability to synthesis a high purity sample with non-deficient Ta2O5\mathrm{Ta}_2\mathrm{O}_5 amounts. In addition, to maintain charge neutrality, there must be oxygen deficiencies that similarly disrupt the superexchange pathway.

  • The high-entropy nature of the M2+/3+\mathrm{M}^{2+/3+} site can result in the local distortion of the M@O6\mathrm{M@O}_6 octahedra, which reduces the orbital overlap between M2+/3+\mathrm{M}^{2+/3+} and the intermediate O2−\mathrm{O}^{2-}. Consequently, electron hopping may not occur due to the altered symmetries of orbitals.

Conclusion

In this paper, we reported the first high-entropy oxide in a trirutile structure. High-purity phase with high configurational disorder in a uniform structure has been determined via powder XRD and EDS measurements. The new material, (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}, shows antiferromagnetic spin-spin coupling under high temperatures while exhibiting short-range antiferromagnetic ordering under low temperatures. Heat capacity further shows the evidence of the absence of long-range magnetic ordering in this compound. XPS shows the presence of divalent Mn, Co, Ni and Cu, along with trivalent Fe, which are consistent with the observation in the magnetic results. The discovery of the first trirutile high-entropy oxide builds a new platform for investigating the interplay between high-entropy nature and their magnetism. Moreover, it allows the manipulation of a wider range of physical properties in high-entropy oxides.

Associated Content

Supporting Information

The Supporting Information is available free of charge at XXX.

Deviation from Curie-Weiss behavior below ~50 K. AC magnetic susceptibility data. Magnetic hysteresis loop. Temperature-dependent resistivity data. Heat capacity data under zero and applied magnetic field. Powder XRD fitted atomic coordinates. EDS results.

Author Information

Corresponding Author: [email protected]

Notes: The authors declare no competing financial interest.

Acknowledgements

G. A. and X.G. are supported by the startup fund from the University of Pittsburgh and the Pitt Momentum Fund. Portions of this work were performed at the Molecular Foundry and supported by the Office of Science, Office of Basic Energy Sciences, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. Work at the University of Arizona is supported by the National Science Foundation under Award No. DMR-2338229.

For Table of Contents Only

Figure 6 (PDF p. 17).

Supporting Information

Element/TransitionPeak Energy (eV)Peak FWHM (eV)Peak Area (eV*cts/s)Peak AssignmentRSFAtomic %
Cu LMM640.071.272124Cu Auger
Ni LMM641.160.921145Ni Auger
Mn 2p3/2642.142.748835Mn2+^{2+}1.75714.38
Ni LMM709.851.402254Ni Auger
Cu LMM710.681.402254Cu Auger
Co LMM711.281.311793Co Auger
Fe 2p3/2712.533.4925885Fe3+^{3+}2.94637.58
Cu LMM716.453.529841Cu Auger
Fe 2p Sat720.824.0510933Satellite
Fe 2p1/2725.633.5712943Fe3+^{3+}
Fe2p sat728.822.883684Satellite
Co LMM776.583.58758Co Auger
Ni LMM777.793.082177Ni Auger
Co 2p3/2780.322.0817520Co2+^{2+}3.52912.04
Co 2p3/2782.042.209975Co3+^{3+}3.52920.41
Fe LMM784.553.0810108Fe Auger
Co 2p sat787.673.089230Satellite
Co 2p sat791.163.465907Satellite
Co 2p1/2795.292.168760Co2+^{2+}
Co2p1/2797.012.204988Co3+^{3+}
Co 2p sat799.603.084216Satellite
Co 2p sat803.963.085244Satellite
Ni 2p3/2856.452.829621Ni2+^{2+}2.30912.30
Ni 2p3 sat861.973.043861Satellite
Cu 2p3/2933.733.2620323Cu2+^{2+}2.6263.29
Cu 2p sat940.793.062462Satellite
Mn LMM943.432.562474Mn Auger

Table S3. Peak fitting of Mn, Fe, Co, Ni, and Cu regions in (Mn0.2_{0.2}Fe0.2_{0.2}Co0.2_{0.2}Ni0.2_{0.2}Cu0.2_{0.2})Ta1.92_{1.92}O6−δ_{6-\delta} in area 1.

Peak fitting plots for Mn, Fe, Co, Ni, and Cu

Figure S4. Peak fitting of Mn, Fe, Co, Ni, and Cu in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} in area 2. B.E. stands for binding energy. Blue plus signs mark satellite peaks while red asterisks mark Auger peaks.

Element/ TransitionPeak Energy (eV)Peak FWHM (eV)Peak Area (eV*cts/s)Peak AssignmentRSFAtomic %
Cu LMM640.380.56193Cu Auger
Ni LMM641.130.91828Ni Auger
Mn 2p3/2642.233.208980Mn2+\mathrm{Mn}^{2+}1.75718.89
Ni LMM709.371.15403Ni Auger
Cu LMM710.21.15492Cu Auger
Co LMM711.751.31677Co Auger
Fe 2p3/2712.663.4916372Fe3+\mathrm{Fe}^{3+}2.94630.71
Cu LMM716.103.787633Cu Auger
Fe 2p3Sat720.824.057005Satellite
Fe 2p1/2725.763.578186Fe3+\mathrm{Fe}^{3+}
Fe2p sat728.822.781859Satellite
Co 2p3/2781.982.076827Co2+\mathrm{Co}^{2+}3.52910.65
Co 2p3/2784.182.204455Co3+\mathrm{Co}^{3+}3.5296.95
Fe LMM787.533.084993Fe Auger
Co 2p sat789.833.083788Satellite
Co 2p sat792.983.582909Satellite
Co 2p1/2796.952.203413Co3O4
Co2p1/2799.152.202228Co3O4
Co 2p sat803.943.082904Satellite
Co 2p sat807.433.081807Satellite
Ni 2p3857.152.276231Ni2+\mathrm{Ni}^{2+}2.3099.85
Ni 2p3 sat862.763.043030Satellite
Cu 2p3/2934.303.5616632Cu2+\mathrm{Cu}^{2+}2.62622.96
Cu 2p sat941.593.062453Satellite
Mn LMM943.942.562712Mn Auger

Table S4. Peak fitting of Mn, Fe, Co, Ni, and Cu regions in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} in area 2.

Peak fitting of Mn, Fe, Co, Ni, and Cu

Figure S5. Peak fitting of Mn, Fe, Co, Ni, and Cu in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} in area 3. B.E. stands for binding energy. Blue plus signs mark satellite peaks wile red asterisks mark Auger peaks.

Element/ TransitionPeak Energy (eV)Peak FWHM (eV)Peak Area (eV*cts/s)Peak AssignmentRSFAtomic (%)
Cu LMM639.950.912134Cu Auger
Ni LMM640.750.56659Satellite
Mn 2p3/22p_{3/2}641.422.498822Mn Auger
Cu LMM639.950.912134Cu Auger
Ni LMM640.750.56659Ni Auger
Mn 2p3/22p_{3/2}641.422.498822Mn2+^{2+}1.7578.90
Ni LMM709.291.43024Ni Auger
Cu LMM710.121.43024Cu Auger
Co LMM710.671.312832Co Auger
Fe 2p3/22p_{3/2}711.723.4940272Fe3+^{3+}2.94636.23
Cu LMM714.973.0211908Cu Auger
Fe 2p Sat719.184.0515814Satellite
Fe 2p1/22p_{1/2}724.823.5720136Fe3+^{3+}
Fe2p sat728.822.781859Satellite
Ni LMM777.793.084287Ni Auger
Co 2p3/22p_{3/2}779.981.8521280Co2+^{2+}3.52915.92
Co 2p3/22p_{3/2}780.952.2019342Co3+^{3+}3.52914.47
Fe LMM783.723.0815241Fe Auger
Co 2p sat787.423.0812465Satellite
Co 2p sat791.163.587264Satellite
Co 2p1/22p_{1/2}794.951.9310640Co2+^{2+}
Co2p1/2795.921.689671Co3+^{3+}
Co 2p sat797.383.086975Satellite
Co 2p sat803.473.086114Satellite
Ni 2p3855.972.3110212Ni2+^{2+}2.3097.74
Ni 2p sat861.733.044714Satellite
Cu 2p3/22p_{3/2}933.142.9425269Cu2+^{2+}2.62616.74
Cu 2p sat940.872.062164Satellite
Mn LMM943.351.861836Mn Auger

Table S5. Peak fitting of Mn, Fe, Co, Ni, and Cu regions in (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} in area 3.

Oxidation States Analysis

X-ray photoelectron spectroscopy (XPS) was performed in a ULVAC-PHI Inc. PHI GENESIS instrument equipped with monochromatic Al Kα_{\alpha} radiation (1486.6 eV) as the excitation source. The X-ray analysis area for measurement was set at 100 μ\mum diameter and a flood gun (1.6 V, 20 μ\muA) was used for charge compensation. The pass energy was 112 eV for the high-resolution regions. The analysis chamber pressure was less than 1×10−71 \times10^{-7} mbar during data acquisition. Fittings were performed with the MultiPak software. C1s C-C was used as a reference at 284.8eV for all spectra. Smart backgrounds were used to fit all elements. Constraints such as peak separation and area ratio confined to 2:1 for doublet peaks were used. Due to the high degree of transition metals with overlapping auger peaks, the peak fitting was nontrivial. For Mn, Ni and Cu, only the 2p3/2_{3/2} peak area was fitted since they had no overlap with peaks outside the fitted region.

Deviation from the Curie-Weiss (CW) behavior at low temperatures

Figure S4 (PDF p. 27). Deviation from the Curie-Weiss (CW) behavior at low temperatures.

AC magnetic susceptibility plot

Figure S5 (PDF p. 28). AC magnetic susceptibility of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} under various frequencies. The applied DC magnetic field is 100 Oe and the AC field is 10 Oe.

Hysteresis loops of $(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta}$ at 2 K and 10 K

Figure S6. Hysteresis loops of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} at 2 K (blue) and 10 K (red).

Resistivity versus temperature with inset plot of ln(rho) versus inverse temperature

Figure S7. Resistivity of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} from 350 K to 390K displaying insulating behavior. The inset graph is of the linear relationship between ln⁡(ρ)\ln(\rho) and T−1T^{-1}. To calculate the electronic bandgap (EgE_g), the Arrhenius equation ρ=ρ0eEg/(2kBT)\rho= \rho_0 e^{E_g/(2k_B T)}, where ρ0\rho_0 is the pre-exponential term constant and kBk_B is Boltzmann’s constant, was used. EgE_g was determined to be 608(1) meV.

Temperature-dependent heat capacity measured under magnetic fields of 0 T and 3 T

Figure S8. Temperature-dependent heat capacity of (Mn0.2Fe0.2Co0.2Ni0.2Cu0.2)Ta1.92O6−δ(\mathrm{Mn}_{0.2}\mathrm{Fe}_{0.2}\mathrm{Co}_{0.2}\mathrm{Ni}_{0.2}\mathrm{Cu}_{0.2})\mathrm{Ta}_{1.92}\mathrm{O}_{6-\delta} measured under magnetic field μ0H=0\mu_0 H = 0 T and 3 T.

Molecular Orbital (MO) Calculation: Semi-empirical extended-Hückel-tight-binding (EHTB) methods and CAESAR packages are used in calculating molecular orbitals of the parent compound, CoTa2O6\mathrm{CoTa}_{2}\mathrm{O}_{6}.[1] The basis sets for Co are: 4s4s: Hii = -9.21 eV, ζ1\zeta_{1} = 2, coefficient1 = 1.0000; 4p4p: Hii = -5.29 eV, ζ1\zeta_{1} = 2, coefficient1 = 1.000; 3d3d: Hii = -13.18 eV, ζ1\zeta_{1} = 5.55, coefficient1 = 0.568, ζ2\zeta_{2} = 2.1, coefficient2 = 0.606. For Ta: 6s6s: Hii = -10.1 eV, ζ1\zeta_{1} = 2.28, coefficient1 = 1.000; 6p6p: Hii = -6.86 eV, ζ1\zeta_{1} = 2.241, coefficient1 = 1.000; 5d5d: Hii = -12.1 eV, ζ1\zeta_{1} = 4.762, coefficient1 = 0.6815, ζ2\zeta_{2} = 1.938, coefficient2 = 0.5589. For O: 2s2s: Hii = -32.29999 eV, ζ1\zeta_{1} = 2.275, coefficient1 = 1.000; 2p2p: Hii = -14.8 eV, ζ1\zeta_{1} = 2.275, coefficient1 = 1.000.

Reference

References

  1. [1]Hoffmann, R. An extended Hückel theory. I. hydrocarbons. J. Chem. Phys. 1963, 39, 1397-1412.DOI

Paper details

vlnc:W_xw3qczy8
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents