betaFeedback

WorksPhysics and Astronomy

Pressure dependent DFT study of mechanical, thermal, electronic, magnetic, and optical properties of EuCd2As2: a magnetic semimetal

Abstract

We present a comprehensive spin-polarized density functional theory (DFT) investigation of the pressure-dependent physical properties of EuCd2As2, a magnetically and topologically rich compound with potential applications in spintronics and optoelectronics technologies. We have investigated the structural, mechanical, thermophysical, acoustic, electronic, magnetic, and optical properties of this material at pressures of 0, 2, 4, 6, and 8 GPa. The calculated lattice parameters at zero pressure are in good agreement with experimental values. The mechanical stability of EuCd2As2 is maintained over the investigated pressure range. The elastic constants, bulk modulus, shear modulus, and Young's modulus are found to be tunable with applied pressure. The compound undergoes a brittle to ductile transition at higher pressures. The Debye temperature, melting temperature, and Grüneisen parameter are found to be strongly pressure-dependent. Phonon thermal conductivity has been evaluated. The electronic properties of EuCd2As2 were studied through band structure and density of states (DOS). The effect of pressure up to 8 GPa was investigated for the ferromagnetic (FM) phase. At 0 GPa, the calculated FM band structure exhibits no band gap at the Fermi level, which confirms the semimetallic nature of EuCd2As2. The net magnetic moment of 6.96 μ_B per unit cell was obtained for this compound indicating its potential for spintronics application. The optical properties, including the dielectric function, refractive index, absorption coefficient, optical conductivity, reflectivity, and loss function, are calculated. The calculated optical spectra indicate strong absorption in the visible and ultraviolet regions, suggesting that EuCd2As2 may have potential for optoelectronic applications.

Introduction

EuCd2_2As2_2 has emerged as a compelling system to study the interplay between magnetism and band topology [1]. This compound has a trigonal crystal structure with a space group P3ˉm1P\bar{3}m1, in which triangular Eu layers are separated by Cd2_2As2_2 bilayers, with magnetism arising primarily from the localized Eu2+^{2+} (4f74f^7, S=7/2S = 7/2) [2]. The low-temperature ground state of EuCd2_2As2_2 has an interesting feature, namely, its electronic properties can change depending on the behavior of its magnetic order at low temperatures. Jo et al. [1] have reported that, depending on the level of band filling, controlled by the Eu-site occupancy during crystal growth, the material can be either in an antiferromagnetic phase or in a ferromagnetic phase. Comprehensive density functional theory (DFT) calculations indicate that the antiferromagnetic (AFM) state can host topological states. In contrast, the ferromagnetic (FM) state exhibits two pairs of Weyl points tuned to one pair of Weyl points by polarizing the spins along the crystallographic cc-direction [3]. Roychowdhury et al. [4] synthesized the FM phase of EuCd2As2\mathrm{EuCd_2As_2} using the salt flux method. They reported the contribution of the Nernst effect and anomalous Hall conductivity in this material caused by the Berry curvature. Moreover, they found that magnetic-field-induced spin canting modifies the electronic band structure and the associated topological response [4]. Ma et al. [5] investigated the temperature-dependent electronic band structure study. They have found the Weyl nodes in the paramagnetic phase below 100 K that originate due to the interaction between the itinerant electrons and localized moments in the paramagnetic phase. However, above approximately 100 K, they reported a crossover from a Weyl-semimetal-like state toward a Dirac-semimetal-like electronic structure. Rahn et al. [6] have synthesized the A-type antiferromagnetic phase of EuCd2As2\mathrm{EuCd_2As_2}, with Eu spins aligned along the abab plane. In this phase, (DFT) calculations suggest that the C3C_3 symmetry is broken, resulting in the opening of a band gap in the vicinity of the Fermi surface. Conversely, when the spins are oriented along the (c)(c)-axis in the antiferromagnetic configuration, the compound is predicted to exhibit a Dirac-semimetal-like state with no gap at the crossing point [6]. However, recent magneto-infrared spectroscopy studies have given new insights into the magneto-optical properties of EuCd2As2\mathrm{EuCd_2As_2}. D. Santos-Cottin et al. [7] have identified EuCd2As2\mathrm{EuCd_2As_2} as a magnetic semiconductor, challenging the previous study of identifying EuCd2As2\mathrm{EuCd_2As_2} as a topological semimetal. While ab initio calculations had suggested Weyl points, and angle-resolved photoemission spectroscopy (ARPES) measurements had revealed a conical shape of the valence band, infrared spectroscopy revealed that EuCd2As2\mathrm{EuCd_2As_2} hosts a significant band gap of 0.77 eV. This finding is particularly significant as several recent studies reproduced EuCd2As2\mathrm{EuCd_2As_2} samples with activated resistivity behavior and confirmed the presence of a substantial band gap. In a magnetic field, the energy gap is modified, but the band gap still remains even in high magnetic fields (16 T), demonstrating a strong magneto-optical response [8]. All these findings suggest that EuCd2As2\mathrm{EuCd_2As_2} as a particularly interesting platform for investigating the interplay between magnetism, electronic structure, and topology, making it a promising material for developing a fundamental understanding of physics as well as for technological applications such as optoelectronics and spintronics. So far, several theoretical investigations have been carried out on EuCd2As2\mathrm{EuCd_2As_2}, such as the electronic configuration, magnetic characteristics, electrical conductivity, and optical attributes of EuCd2As2\mathrm{EuCd_2As_2} [9]. Thermoelectric parameters such as Seebeck coefficient, electrical and thermal conductivity, power factor, and figure of merit (ZT) as a function of temperature, as well as chemical potential of EuCd2As2\mathrm{EuCd_2As_2} for anti-ferromagnetic phase, have been investigated using ab-initio (DFT) and semiclassical Boltzmann transport theory within constant relaxation time approximation [10]. Moreover, DFT calculations have been performed to analyze electronic band structure of EuCd2As2\mathrm{EuCd_2As_2} for different magnetic configurations, including in-plane, out-of-plane, and spin-canted states [11]. Additionally, it was analyzed how spin orientation and canting affect the formation and position of Weyl points near the Fermi level [11].

To our knowledge, a systematic first-principles investigation of its pressure-dependent elastic, mechanical, thermophysical, acoustic, and optical properties remains limited for EuCd2As2\mathrm{EuCd_2As_2}. Pressure is a clean tunning parameter that can be varied continuously to control the physical properties of solids. In this work we have investigated a large number of electronic and thermophysical properties of EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} within a moderate pressure range from 0 to 8 GPa. This range is easily accessible in high pressure laboratories. Our findings not only show a novel pressure dependent pathway to optimize the material's mechanical stability and thermal management but also hold promise for increasing its efficiency in spintronic and thermoelectric applications. Taddei et al. [11, 12] experimentally and computationally studied a FM EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2}. In the present work, we extend the study by Taddei et al. by investigating pressure-dependent structural, elastic, mechanical, acoustic, thermophysical, electronic, and optical properties of the FM phase EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} using first-principles calculations. This work presents a comprehensive property coverage by combining structural, mechanical, electronic, optical, and thermal properties, providing a broad-based understanding of the material.

Computational methodology

The structural, elastic, thermo-physical, magnetic, and optical properties of EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} were studied using density functional theory (DFT) within the generalized gradient approximation (GGA) [13]. The calculations were carried out using the Perdew–Burke–Ernzerhof (PBE) exchange-correlation functional as implemented in the CASTEP code [14]. The ultrasoft pseudopotential setting is used for this compound. For the CASTEP calculations, a plane-wave cut-off energy of 750 eV and a Monkhorst–Pack k-point grid [15] of 12×12×712 \times12 \times7 were used to sample the Brillouin zone (BZ). Since EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} is a magnetic material, spin-polarized calculations with collinear treatment were performed. The crystal structure was optimized using the BFGS minimization method [16]. During this calculation the total energy convergence tolerance was set to 5.0×10−65.0 \times10^{-6} eV/atom, while the maximum ionic force, maximum ionic displacement, and maximum stress were limited to 0.01 eV/Å, 5.0×10−45.0 \times10^{-4} Å, and 0.02 GPa, respectively. The independent single-crystal elastic constants (CijC_{ij}), bulk modulus (BB), and shear modulus (GG) were calculated using the stress–strain method implemented in the CASTEP code. After obtaining the optimized structure, the electronic and magnetic properties were calculated. The magnetic behavior was analyzed from self-consistent spin-polarized calculations. The optical properties were obtained from the frequency-dependent dielectric function. Other optical parameters were evaluated through the Kramers–Kronig relations available in the CASTEP package. The optical properties of materials can be understood by their frequency dependent dielectric function ε(ω)\varepsilon(\omega). The dielectric function can be written as ε(ω)=ε1(ω)+iε2(ω)\varepsilon(\omega) = \varepsilon_{1}(\omega) + i\varepsilon_{2}(\omega). Here ε1(ω)\varepsilon_{1}(\omega) and ε2(ω)\varepsilon_{2}(\omega) correspond to the real and imaginary parts of the dielectric constants, respectively. For electronic band structure Quantum ESPRESSO [17] GGA approximation with PBE functional is used. Since EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} is a magnetic material, spin-polarized calculations were carried out during the study. Interatomic interactions and electronic structures were described using a scalar relativistic pseudopotentials sourced from the Standard Solid State Pseudopotentials (SSSP) library within the PBE generalized gradient approximation and [18]. A plane-wave kinetic energy cutoff of 55 Ry and a charge density cutoff of 440 Ry were used in all calculations. A Monkhorst–Pack k-point grid [15] of 12×12×712 \times12 \times7 were used to sample the Brillouin zone (BZ). The self-consistent field calculations were performed with an energy convergence threshold of 4×10−54 \times10^{-5} Ry. And the force convergence threshold was 5×10−45 \times10^{-4} Ry/Bohr. Charge density mixing was carried out using the plain mixing scheme with a mixing parameter of 0.3.

Results and discussion

Structural Properties

The compound EuCd2_2As2_2 has a trigonal crystal structure with a specific space group. Almost all physical properties, such as band structure, optical properties, and elastic constants, depend on the crystal structure and the nature of the constituent atoms. The crystal structures of EuCd2_2As2_2 are shown in Figure 1 and Figure 2. These crystal structures were visualized using VESTA [19]. The Wyckoff positions are taken from a previous study [2]. The EuCd2_2As2_2 has a layered structure. In this structure the Cd2_2As2_2 bilayers are separated by the triangular Eu layers. The magnetic moments primarily originates from the Eu2+^{2+} ions [5]. The lattice parameters obtained from optimization at 0 GPa were compared with those of experimental results in Table 1. It is seen from Table 1 that the calculated lattice parameters a = b and c for EuCd2_2As2_2 are in good agreement with the experimental results. Moreover, the volume of the unit cell is very close to the experimental result. This is a crucial step to judge the reliability of this computational work. Moreover, lattice parameters are studied under several pressures up to 8 GPa, and the result is shown in Figure 3 and Table 1. The lattice parameters are found to decrease with increasing pressure. The unit cell volume decreased by 11.70% as pressure increased from 0 GPa to 8 GPa. In the Figure 3 a0a_0, c0c_0 and V0V_0 are the lattice parameters and unit cell volume respectively under zero pressure.

Three-dimensional crystal structure of EuCd2As2

Figure 1. Three-dimensional (3D) crystal structure of EuCd2_2As2_2 where the vectors indicates the direction of magnetic moment .

Two-dimensional 2D view of the ab-plane of crystal structure of EuCd₂As₂

Figure 2. Two-dimensional 2D view of the ab-plane of crystal structure of EuCd₂As₂.

Pressure (GPa)a=ba=bcca/a0a/a_0c/c0c/c_0VVV/V0V/V_0Remarks
-4.4507.350--126.000-[2]
04.5007.32211128.4051This work
24.4527.2030.9890.983123.6230.963This work
44.4127.1020.9800.970119.6930.932This work
64.3767.0130.9720.958116.3260.906This work
84.3456.9340.9660.947113.3880.883This work

Table 1. Optimized lattice parameters under pressures (a=ba=b, and cc in Å), cell volume VV in Å3^3 of EuCd₂As₂.

Normalized lattice parameters, elastic constants, and elastic moduli

Figure 3. (a) Normalized lattice parameters and volume (a/aoa/a_{\mathrm{o}}, c/coc/c_{\mathrm{o}}, V/VoV/V_{\mathrm{o}}), b) Elastic constants CijC_{ij} and, (c) Elastic moduli under pressures.

Elastic Properties

Elastic constants

From the elastic constants of a crystalline solid, the mechanical behavior and stability under external stress can be understood. These elastic constants are related to the material’s mechanical stability, stiffness, ductility, brittleness, and elastic anisotropy [20]. For a material to be mechanically stable, the Born-Huang conditions must be satisfied. As the selected compound EuCd2_2As2_2 has a trigonal crystal structure, stability conditions under pressure are [21]:

C44−P>0C11−P−∣C12+P∣>0(C33−P)(C11+C12)−2(C13+P)2>0(C44−P)(C11−C12−2P)−2C142>0(1)\begin{aligned} C_{44} - P &> 0 \\ C_{11} - P - \lvert C_{12} + P \rvert&> 0 \\ (C_{33} - P)(C_{11} + C_{12}) - 2(C_{13} + P)^2 &> 0 \\ (C_{44} - P)(C_{11} - C_{12} - 2P) - 2C_{14}^{2} &> 0 \tag*{(1)} \end{aligned}

As shown in Table 2, the calculated elastic constants satisfy the stability conditions for the selected pressures. The elastic constant C11C_{11} characterizes a material's resistance to compression along the [100] direction, while C33C_{33} describes resistance along the [1] direction. EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} is less compressible along the [100] direction compared to the [1] direction, since C11C_{11} is significantly larger than C33C_{33} under all pressures. This indicates stronger atomic bonding along a direction. C12C_{12}, C13C_{13}, and C23C_{23} are the elastic constants that describe how stress along one crystal axis produces strain along a different axis. Specifically, C12C_{12} links stress in the a-direction to strain along the b-axis; C13C_{13} links stress in the a-direction to strain along the c-axis; and C23C_{23} links stress in the b-direction to strain along the c-axis. For EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2}, C12C_{12} is moderately greater than C13C_{13} under all pressures. So, it is easy to produce deformation along a direction by applying strain along the b-direction compared to the c-direction. The elastic constant C44C_{44} represents the material’s ability to resist shear deformation when a tangential force is applied along the [10] direction on the (100) plane. For EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2}, C44C_{44} has a very low value compared to C11C_{11} and C33C_{33}. So, it is easier to deform the material by applying a shearing force than a compressive force. The resistance of the (100) plane to shear along the [11] direction is characterized by the elastic constant C55C_{55}. From Table 2, we can see that there is a small difference between C55C_{55} and C66C_{66}. With increasing pressure, both parameters increase slightly, but C66C_{66} remains greater than C55C_{55}. From Figure 3 (b) and Table 2, we can see that C11C_{11}, C33C_{33}, C44C_{44}, and C66C_{66} increase with increasing pressure. C12C_{12} and C13C_{13} increase with increasing pressure. Therefore, we can conclude that pressure can be a useful tool to tune the elastic properties of EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2}. Positive Cauchy pressure indicates ductility, while negative Cauchy pressure indicates a brittleness. Positive Cauchy pressure indicates predominance of ionic/metallic bonding where negative Cauchy pressure indicates predominance of covalent bonding. For trigonal EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} the Cauchy pressures can be defined as (C13−C44)(C_{13} - C_{44}) for (100) and (010) planes and (C12−C66)(C_{12} - C_{66}) for the (001) plane [22]. From Table 2, we see that at zero pressure the Cauchy pressures are negative, which indicates a brittle nature. For higher pressures, the Cauchy pressures are positive, which indicates a ductile nature, and they increase, indicating that the ductility of the material can be adjusted by applied pressure.

Pressure (GPa)C11=C22C_{11} = C_{22}C12C_{12}C13=C23C_{13} = C_{23}C33C_{33}C44=C55C_{44} = C_{55}C66C_{66}(C13−C44C_{13} - C_{44})(C12−C66C_{12} - C_{66})
096.6430.1228.2175.6328.2733.26-0.06-3.14
2109.6538.3835.7885.6431.0635.644.722.74
4121.5045.4243.3394.9633.2738.0410.067.38
6131.0954.5350.95104.0734.3038.2816.6516.25
8140.6561.5658.07112.2334.9739.5523.1022.01

Table 2. Elastic constants CijC_{ij} in GPa, and Cauchy pressures PCP_{\mathrm{C}} in GPa under several pressures of EuCd2_2As2_2.

Moduli of elasticity

To clearly understand the overall mechanical characteristics, the elastic moduli (YY, BB, and GG) are calculated. To calculate these elastic moduli, the Voigt-Reuss-Hill (VRH) method is used [23], [24], [25] and listed in Table 3. The Young’s modulus for EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} is found to be 74.13 GPa under zero pressure, indicating relatively low stiffness compared with many structural metals, such as iron. Young’s modulus is a measure of resistance to longitudinal deformation. So this lower value of Young’s modulus indicates the soft nature of this compound. The critical thermal shock coefficient is inversely proportional to Young’s modulus [26]. So the compound in this study has a moderate critical thermal shock coefficient. From Figure 3 (c) and Table 3, we can see that with increasing pressure from 0 to 2 GPa, the Young’s modulus increases from 74.13 GPa to 81.06 GPa. Then, from 2 to 8 GPa pressure, it increases moderately up to 93.19 GPa. This increase indicates that EuCd2_2As2_2 becomes stiffer against elastic deformation as the applied pressure increases. The value of Young’s modulus at 8 GPa of pressure is much lower than that of pure steel but is comparable to that of brass. The bulk modulus B describes the material’s resistance to volume compression or fracture under applied pressure, whereas the shear modulus G characterizes its resistance to shape deformation or plastic distortion. The bulk modulus is closely related to the average binding energy of the atoms in crystals. For this compound, the bulk modulus is greater than the shear modulus at zero pressure, which indicates that the shear component should control the mechanical failure of EuCd2_2As2_2. From Table 3 and Figure 3 (c), we can see bulk modulus and shear modulus also increase with increasing pressure. Table 3 further shows that the difference between the Voigt and Reuss values is very small. According to Hill, when these upper and lower bounds are close to each other, it means that the material has low elastic anisotropy [25].

Pressure (GPa)BR_RBV_VBH_H = BGR_RGV_VGH_H = GG/BYHill_{\mathrm{Hill}}σ\sigma
048.4049.1148.7629.3530.1229.730.6174.130.25
257.4258.3157.8731.4432.5531.990.5581.060.27
465.9166.9066.4133.0234.6433.830.5186.760.28
674.3675.4674.9134.0735.3734.720.4690.220.30
882.0583.2182.6334.7436.2935.510.4393.190.31

Table 3. Calculated values of bulk modulus (B) in GPa, shear modulus (G) in GPa and Young’s modulus (Y) in GPa, Pugh ratio (G/B), Poisson’s ratio (σ\sigma) of EuCd2_2As2_2 calculated in this study.

Ductility and brittleness

The Pugh ratio is a parameter commonly used to assess the brittle or ductile nature of a material. It is defined as the ratio of the shear modulus to the bulk modulus, (G/B) [27]. A Pugh ratio below 0.57 generally indicates ductile behaviour, whereas a value above this threshold suggests brittle behaviour. As shown in Table 3, the Pugh ratio is below 0.57 at all investigated external pressures, indicating that EuCd2_2As2_2 exhibits ductile behavior under external pressure. Similarly, a Poisson's ratio greater than 0.26 is generally associated with ductility, whereas a lower value indicates a tendency towards brittle behaviour [28]. Table 3 shows that the Poisson's ratio of EuCd2_2As2_2 is 0.25 at zero pressure, suggesting that the material is close to the conventional ductile-brittle threshold. Poisson's ratio can also provide insight into the bonding characteristics of a material. Values between 0.25 and 0.50 are commonly associated with the dominance of central forces in stabilizing the material [29], [30], whereas values outside this range may suggest a greater contribution from non-central forces. Since the Poisson's ratio of EuCd2_2As2_2 falls within this range over the investigated pressure interval, the results suggest that central forces play an important role in its mechanical stability. As the pressure increases from 0 to 2 GPa, the Poisson's ratio rises from 0.25 to 0.27, while the Pugh ratio decreases from 0.61 to 0.55. From 2 to 8 GPa, the Pugh ratio continues to decrease, whereas the Poisson's ratio increases further, as shown in Figure 4. These trends indicate that external pressure can be used to regulate the ductile-brittle response of EuCd2_2As2_2.

Pugh's ratio and Poisson's ratio versus applied pressure

Figure 4. (a) Pugh’s ratio vs applied pressure in GPa (b) Poisson’s ratio ν\nu vs applied pressure in GPa.

Machinability

The machinability index (μM\mu_{\mathrm{M}}) is defined by the following equation [31].

μM=BC44(2)\mu_{\mathrm{M}} = \frac{B}{C_{44}} \tag*{(2)}

This parameter indicates how easily a material can be cut, drilled, milled, or shaped using machine tools. In this study, the machinability index of EuCd2_2As2_2 is calculated to be 1.72 at zero pressure, suggesting moderate machinability. As shown in Table 4, the machinability index increases slightly to 1.86 at 2 GPa. It further increases to 2.00 at 4 GPa and reaches 2.36 at 8 GPa. These results indicate that the machinability of EuCd2_2As2_2 improves significantly with increasing pressure, suggesting that external pressure may provide a means of tuning its machinability.

Applied pressure in GPaMachinability index (μM\mu_M)
01.72
21.86
42.00
62.18
82.36

Table 4. Machinability index at different pressures of EuCd2_2As2_2.

Elastic anisotropy

Elastic anisotropy is an important factor that affects how a material responds to different kinds of stress and strain. Anisotropy indices show how the material’s mechanical properties vary across different directions. Elastic anisotropy influences many physical processes, such as how crystals deform, tiny cracks spread, quantum dots align, heat moves through the material, and overall defects dynamics. It also affects the material’s toughness. In crystals, covalent bonds usually cause anisotropic (direction-dependent) behavior, while metallic bonds usually make the material behave isotropically (same in all directions) [20, 32]. The amount of anisotropy in atomic bonds on different crystal planes can be measured using shear anisotropy factors A1A_1, A2A_2, and A3A_3. A1A_1, A2A_2, and A3A_3 are the shear anisotropy factors for the (100), (010), and (001) planes, measured along the [11]–[10], [101]–[1], and [110]–[10] directions, respectively [33]. If a crystal is isotropic with respect to the different shear planes, A1=A2=A3=1A_1 = A_2 = A_3 = 1. From Table 5, it is seen that both A1A_1 and A2A_2 have a value of 0.976 at zero pressure, but A3A_3 has a value very equal to 1 at zero pressure. With increasing pressure, A1A_1 and A2A_2 are approximately equal to 1, and A3A_3 is 1. So under ambient and higher pressures, the crystal is isotropic with respect to the different shear planes. The other anisotropy parameters AGA_G, ABA_B, ALA_L, AUA^U, and AeqA_{\mathrm{eq}} are calculated using the formulae stated in references [34], [35], [36], [37]. When AG=AB=0A_G = A_B = 0, the material exhibits perfect elastic isotropy. On the other hand, the condition AG=AB=1A_G = A_B = 1 corresponds to the highest possible elastic anisotropy. In the present study, both AGA_G and ABA_B were found to have values very close to zero under all pressures, which indicates excellent elastic isotropy in compressibility and in shear. The universal anisotropy index AUA^U considers contributions from both the shear and bulk moduli. If AUA^U deviates from zero, the crystal exhibits elastic anisotropy. In contrast, AU=0A^U = 0 corresponds to a completely isotropic crystal [38]. In this study, AUA^U was found to be equal to 0.145, which is small and indicates low anisotropy. But at the higher pressures values of AUA^U lie within the range from 0.192 to 0.261. This indicates a small increment of anisotropy. In locally isotropic crystals, AeqA_{\mathrm{eq}} is equal to 1. But in this study, AeqA_{\mathrm{eq}} was found to have a value of 1.413 at zero pressure, which indicates a small anisotropy. The parameter ALA_L generally varies within the interval 0-10.26 for inorganic crystalline compounds [39]. AL=0A_L = 0 corresponds to complete elastic isotropy. The computed value of ALA_L at zero pressure is 0.041, which is a further indication of very low anisotropy. At higher pressures, the value of ALA_{\mathrm{L}} is almost zero. From Figure 5 (a), it is seen that with an increment in pressure from 0 to 6 GPa, there is an increment in A1A_1 and in A2A_2, from 6 to 8 GPa A1A_1 and in A2A_2 decreases. Pressure has noticeable effect on AeqA_{\mathrm{eq}}, and AUA^{\mathrm{U}} as seen in Figure 5 (b).

Pressure (GPa)A1A_1A2A_2A3A_3AUA^{\mathrm{U}}AeqA_{\mathrm{eq}}AGA_{\mathrm{G}}ABA_{\mathrm{B}}ALA_{\mathrm{L}}
00.9760.9761.0000.1451.4130.0130.0070.041
21.0041.0041.0000.1921.4880.0170.0080.034
41.0251.0251.0000.2611.5880.0240.0070.032
61.0301.0301.0000.2051.5070.0190.0070.024
81.0231.0231.0000.2371.5540.0220.0070.028

Table 5. Shear anisotropy factor (A1A_1, A2A_2 and A3A_3), the universal anisotropy index AUA^{\mathrm{U}}, equivalent Zener anisotropy measure AeqA_{\mathrm{eq}}, anisotropy in shear AGA_{\mathrm{G}}, anisotropy in compressibility ABA_{\mathrm{B}}, universal log-Euclidean index ALA_{\mathrm{L}}, of EuCd2_2As2_2.

Elastic anisotropy indices and their pressure dependence, with panels (a) and (b)

Figure 5. Elastic anisotropy indices and their pressure dependence for EuCd2_2As2_2.

In an isotropic solid, the three-dimensional representations of Young’s modulus (Y), shear modulus (G), linear compressibility β\beta, and Poisson’s ratio (σ\sigma) are spherical, indicating that these properties are independent of direction. Any deviation from a spherical shape reflects elastic anisotropy. In this study, the directional dependence of these properties for EuCd2_2As2_2 was analyzed using the ELATE tool [40]. The elastic stiffness matrix was used as input to ELATE to generate the three-dimensional surfaces shown in Figure 6-Figure 9, allowing the anisotropic behavior of Young’s modulus, shear modulus, Poisson’s ratio, and linear compressibility to be examined.

Directional dependence in Young's modulus of EuCd2As2 compound

Figure 6. Directional dependence in Young's modulus (Y) of EuCd2_2As2_2 compound.

Directional dependence in Poisson’s ratio of EuCd₂As₂ compound

Figure 9. Directional dependence in Poisson’s ratio (σ\sigma) of EuCd2_2As2_2 compound.

Directional dependence in linear compressibility of EuCd2As2 compound

Figure 7. Directional dependence in linear compressibility (β\beta) of EuCd2_2As2_2 compound.

Directional dependence in shear modulus of EuCd₂As₂ compound

Figure 8. Directional dependence in shear modulus (GG) of EuCd2_2As2_2 compound.

Thermophysical properties

Debye temperature

The Debye temperature ΘD\Theta_D is an important parameter, defined as the temperature above which the phonon wavelength in a material is nearly equal to the interatomic separation. This value is a critical threshold for distinguishing between high and low temperature regimes of a solid. Understanding of Debye temperature (ΘD\Theta_D) is essential for characterizing various thermophysical properties, including melting temperatures, bonding forces, thermal conductivity, specific heat, and phonon dynamics. In the high temperature limit (T >> ΘD\Theta_D), all vibrational modes have approximately equal energy (kBTk_BT). At temperatures below ΘD\Theta_D, high-frequency modes are effectively ”frozen,” and only the acoustic modes are responsible for vibrational excitations. As a result, the Debye temperature calculated from elastic constants aligns closely with values derived from specific heat measurements in the low-temperature range. In this study, the Debye temperature of EuCd2_2As2_2 is calculated using the Anderson model. Equation for Debye temperature is given by [41].

ΘD=hkB[3n4π(NAM)]13vm(3)\Theta_D = \frac{h}{k_B}\left[\frac{3n}{4\pi}\left(\frac{N_A}{M}\right)\right]^{\frac{1}{3}}v_m \tag*{(3)}

In this equation kBk_B is the Boltzmann constant, hh is Planck’s constant, and vmv_m is the mean sound velocity. The Debye temperature ΘD\Theta_D for the compound EuCd2_2As2_2 is found to be 233.29 K at zero pressure. This value is low, indicating that this compound is not stiff in nature, consistent with the elastic parameter analysis. But with increasing pressure, the Debye temperature rises to 240.88 K for 2 GPa, and it is 246.54 K for 4 GPa, and finally at 8 GPa it is 251.44 K, as shown in Table 6 and Figure 10 (b). Thus, pressure is an effective parameter to control a large number of thermophysical properties of this compound.

Applied pressure in GPaDebye temperature in K
0233.29
2240.88
4246.54
6249.39
8251.44

Table 6. Pressure dependent Debye temperature of EuCd2_2As2_2.

Pressure dependent sound velocities, Debye temperature, and melting temperature

Figure 10. Pressure dependent (a) sound velocities, (b) Debye temperature, (c) melting temperature.

Melting temperature

Another important thermophysical parameter of solids to understand stronger atomic interaction, bonding energy, cohesive energy, and coefficient of thermal expansion is the melting temperature, TmT_{\mathrm{m}}. The following empirical relationship is used to calculate the melting temperature in terms of the elastic constants C11C_{11} and C33C_{33} [42]:

Tm=354+1.5(2C11+C33)(4)T_{\mathrm{m}} = 354 + 1.5\left(2C_{11} + C_{33}\right) \tag*{(4)}

The estimated melting temperature was found to be 757.36 K at zero pressure. This melting temperature is much lower in comparison to carbon steel [43]. So, the compound EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} is suitable only for low temperature applications. From Figure 10 (c), it is evident that there is a notable effect of pressure on melting temperature. Therefore, by varying the pressure, atomic interaction, bonding energy, cohesive energy, and coefficient of thermal expansion can be tuned. Moreover, with increasing pressure, the thermal stability can be improved for EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2}.

Pressure in GPaMelting temperature in K
0757.36
2811.44
4860.93
6903.38
8944.30

Table 7. Pressure dependent melting temperature for EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2}.

Grüneisen parameter and phonon thermal conductivity

The Grüneisen parameter, denoted by γ\gamma, is an important thermodynamic quantity that measures the degree of anharmonicity in a solid. It plays a significant role in several physical properties, such as thermal expansion, thermal conductivity, acoustic wave attenuation, and the temperature dependence of elastic constants. A larger value of γ\gamma indicates stronger anharmonic effects within the material. Using Poisson’s ratio (σ\sigma), the Grüneisen parameter for EuCd2_2As2_2 can be estimated from the following relation [44]:

γ=3(1+σ)2(2−3σ)(5)\gamma= \frac{3(1+\sigma)}{2(2-3\sigma)} \tag*{(5)}

From Table 8 and Figure 11 (a), it is seen that the Grüneisen parameter increases with pressure with applied pressure.

Applied pressure GPaGrüneisen parameter γ\gammaPhonon thermal conductivity kphk_{\mathrm{ph}}
01.508.702
21.607.825
41.677.560
61.776.422
81.845.948

Table 8. Pressure-dependent Grüneisen parameter γ\gamma and phonon thermal conductivity kphk_{\mathrm{ph}} in W/mK at 300 K.

Pressure dependent Grüneisen constant and phonon thermal conductivity

Figure 11. Pressure dependent (a) Grüneisen constant, and (b) phonon thermal conductivity at 300 K.

Phonon thermal conductivity quantifies heat transfer through the vibrational motion of lattice ions in a solid [44], [45]. This parameter is vital for determining the energy conversion efficiency of thermoelectric materials. While both electrons and phonons act as heat carriers, electrons are the dominant transporters in metals at low temperatures. However, for materials used in high-temperature applications such as heat sinks, sensors, and thermal barrier coatings, study of lattice thermal conductivity is essential. Using the Slack model, the lattice thermal conductivity (kphk_{\mathrm{ph}}) is estimated by the following expression [44]:

kph=A(γ)MavΘD3δγ2n2/3T(6)k_{\mathrm{ph}} = A(\gamma)\frac{M_{\mathrm{av}}\Theta_{\mathrm{D}}^{3}\delta}{\gamma^{2}n^{2/3}T} \tag*{(6)}

Here, MavM_{\mathrm{av}} (in kg/mol) is the average atomic mass, δ\delta is the cubic root of the average atomic volume in meter, and γ\gamma is the Grüneisen constant, and the factor A(γ)A(\gamma) can be calculated using the following equation [46]:

A(γ)=4.85628×1072(1−0.514γ−0.228γ2)(7)A(\gamma)=\frac{4.85628 \times10^{7}}{2\left(1-\frac{0.514}{\gamma}-\frac{0.228}{\gamma^{2}}\right)} \tag*{(7)}

It is observed that EuCd2As2EuCd_{2}As_{2} possesses a phonon thermal conductivity 8.702 W/m.K at room temperature at zero pressure (Table 8). As we increase pressure, the phonon thermal conductivity decreases to 7.825 W/m.K at 2 GPa, and then it decreases and becomes 7.560 W/m.K at 4 GPa. It further decreases and finally becomes 5.948 W/m.K at 8 GPa. So, the phonon thermal conductivity can be adjusted over a wide range by changing pressure as seen from the Figure 11 (b).

Acoustic velocities

The speed of sound in a material is related to stiffness, crystal density, Debye temperature and thermophysical properties [47]. It also conducts electricity and heat. In recent years, many fields such as physics, materials science, musical instrument design, seismology, geology, and medical science have become very interested in studying the acoustic properties of materials and composites. The bulk and shear moduli are related to the speed of longitudinal and transverse waves of sound by the following equations [48]:

vl=3B+4G3ρ(8)v_{l}=\sqrt{\frac{3B+4G}{3\rho}} \tag*{(8)}
vt=Gρ(9)v_{t}=\sqrt{\frac{G}{\rho}} \tag*{(9)}

Using the following equation, the average sound velocity in a solid can be determined from transverse and longitudinal sound velocities [48]:

vm=[13(2vt3+1vl3)]−1/3(10)v_m = \left[\frac{1}{3}\left(\frac{2}{v_t^3}+\frac{1}{v_l^3}\right)\right]^{-1/3} \tag*{(10)}

In Table 9}, the calculated acoustic velocities are shown. Every atom within a solid exhibits three modes of vibration: a single longitudinal mode and two transverse modes. In an anisotropic crystal, pure longitudinal and transverse modes manifest only along specific axes. From Table 9, we can see that the longitudinal velocity vlv_l is greater than the transverse velocity vtv_t under all pressures. With an increasing pressure, from 0 to 8 GPa there is a noticeable increase in both vlv_l and vtv_t [Fig. 10 (a)]. This increment in sound velocities indicates that with applied pressure the hardness of the compound increases, which is consistent with the analysis in the previous section. In EuCd2_2As2_2, transverse and longitudinal modes can only be present in the symmetry directions of [100] and [1] because of the trigonal symmetry of the material. The acoustic velocities of EuCd2_2As2_2 in these primary directions can be computed using the single crystal elastic constants [49].

Pressure in GPaρ\rhovlv_lvtv_tvmv_m
06.813602.862089.452318.76
27.083769.552126.692365.67
47.313906.602151.732398.12
67.524015.252149.002400.17
87.714106.002145.872402.59

Table 9. Calculated density in gm/cm3^3, longitudinal, transverse and average sound velocities (vlv_l, vtv_t and vmv_m in m/s) of EuCd2_2As2_2.

[100] direction:

[100]vl=C11−C122ρ;[010]vt1=C11ρ;[001]vt2=C44ρ(11)\left[100\right]v_l = \sqrt{\frac{C_{11}-C_{12}}{2\rho}};\quad\left[010\right]v_{t1} = \sqrt{\frac{C_{11}}{\rho}};\quad\left[001\right]v_{t2} = \sqrt{\frac{C_{44}}{\rho}} \tag*{(11)}

[1] direction:

[001]vl=C33ρ;[100]vt1=[010]vt2=C44ρ(12)\left[001\right]v_l = \sqrt{\frac{C_{33}}{\rho}};\quad\left[100\right]v_{t1} = \left[010\right]v_{t2} = \sqrt{\frac{C_{44}}{\rho}} \tag*{(12)}

From Table 10, it is noticeable that there is a significant anisotropy in the longitudinal velocity along [100] and [1] directions. Anisotropy in sound velocity is caused by anisotropy in elastic properties.

Applied pressure in GPa[100] direction[100] direction[100] direction[1] direction[1] direction[1] direction
[10]vt1_{v_t1}[100]vl_{v_l}[1]vt2_{v_t2}[1]vl_{v_l}[100]vt1_{v_t1}[10]vt2_{v_t2}
02209.823766.962037.403332.432037.402037.40
22243.583935.512094.523478.022094.522094.52
42282.604079.602134.873607.132134.872134.87
62256.614175.902136.143720.582136.142136.14
82264.454270.462129.493814.652129.492129.49

Table 10. Anisotropic sound velocities(in m/s) in EuCd2_2As2_2 along principal crystallographic direction under several pressures.

Electronic properties

Band structure

To understand the electronic, optical, and magnetic properties of a material at a microscopic scale, we need to study its electronic band structure [38] [50] [51]. From the band structure, we can calculate the effective masses of charge carriers. The band structure also determines how charges move through the material and how atoms bond with each other [38]. In this study, the band structure of EuCd2_2As2_2 is calculated along high symmetry path Γ\Gamma-A-H-K-Γ\Gamma-M-L-H in Figure 12 for zero pressure and in Figure 13 for 8 GPa. The bands below the Fermi level are the valence band; on the other hand, the bands above the Fermi level are the conduction band. The horizontal line placed at zero energy indicates the Fermi level.

Band structure obtained from Quantum Espresso in ferromagnetic phase at 0 GPa, with a van Hove singularity close to the Fermi level in the conduction band shown in the side panel

Figure 12. Band Structure obtained from Quantum Espresso in ferromagnetic phase at 0 GPa. A van Hove singularity close to the Fermi level in the conduction band is shown in the side panel.

Band Structure obtained from Quantum Espresso in ferromagnetic phase at 8 GPa

Figure 13. Band Structure obtained from Quantum Espresso in ferromagnetic phase at 8 GPa.

Band structures of Figure 12 & Figure 13 are obtained from Quantum Espresso for the ferromagnetic phase. The effect of pressure is illustrated in Figure 4. In Figure 15 for PDOS of Eu, we see that the PDOS for up spin and down spin are not symmetric so there is a nonzero net magnetic moment in EuCd2_2As2_2, which originates from f-electrons of Eu; this is consistent with the previous study [2]. Moreover, we found the magnetic moment to be 6.96 μB\mu_{\mathrm{B}} for 0 GPa. From Figure 12, we can see that near the Fermi level, near Γ\Gamma-point, there is no band gap, which indicates the semimetallic nature of the material in the ferromagnetic phase which is also consistent with the previous study [11]. At higher pressures, the semimetallic nature in the ferromagnetic phase (Figure 13) is sustained. Interestingly, total number of bands crossing the Fermi level increases with increasing pressure. This is an indication of pressure induced Lifshitz transition in EuCd2_2As2_2. This should lead to pressure induced changes in the Fermi surface topology. Also, we find a van Hove singularity feature close to the Fermi level at the Γ\Gamma-point. This feature disappears when pressure is raised (see Figure 13). A major effect of pressure on the band structure is a consistent shift of dispersion branches to lower energies in the valence band and to higher energies in the conduction band. The band widths also increase with increasing pressure. In Figure 14, we see the comparison in the band structure at 0 and 8 GPa. Overall, pressure affects the electronic band structure quite strongly. This suggests that pressure can be employed as an efficient tunning parameter to control the electronic properties of EuCd2_2As2_2.

Band structure obtained from Quantum Espresso in ferromagnetic phase at 0 and 8 GPa

Figure 14. Band Structure obtained from Quantum Espresso in ferromagnetic phase at 0 and 8 GPa.

Total and partial density of states of EuCd2As2 at zero pressure

Figure 15. Total and partial density of states of EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} at zero pressure. The vertical lines indicate the Fermi level.

Electronic density of states

The density of states (DOS) describes the number of electronic states available per unit energy interval. The distribution of states in the valence and conduction bands provides useful insight into the electronic structure and can help explain the electrical, magnetic and optical properties of crystalline materials. The contributions of individual atoms and their orbitals can be investigated by analyzing the total density of states (TDOS) and partial density of states (PDOS). In this study, the TDOS and PDOS of EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} at zero pressure are presented in Figure 15. The relative positions and hybridization of atomic-orbital states can also provide insight into bonding and anti-bonding interactions. The vertical line in Figure 15 represents the Fermi level. The DOS exhibits prominent features at approximately −0.33 eV-0.33\,\mathrm{eV} and 3.86 eV3.86\,\mathrm{eV}, which are attributed to bonding and anti-bonding-related states, respectively, based on the calculated electronic structure. The TDOS at the Fermi level is very small, suggesting a low density of available electronic states near the Fermi energy, consistent with semimetallic behavior supported by the band structure. A minimum in the TDOS between the prominent peaks, referred to as a pseudogap, lies close to the Fermi level. The presence of a pseudogap may indicate an energetically favorable distribution of electronic states; however, it does not, by itself, establish the thermodynamic stability of the compound.

In the valence-band region, As-p states make a major contribution to the PDOS of As, while Eu-f states dominate the Eu contribution. Cd-d states contribute little to the Cd PDOS near Fermi level. In the conduction-band region, the contribution from As-p states is comparatively small, whereas Eu-f and Eu-d states make noticeable contributions. A small contribution from Cd-p states is also observed. Near the Fermi level, the electronic states are contributed mainly by Eu-f, Eu-d, and As-p orbitals, according to the calculated PDOS. The peak in TDOS at about -10 eV comes from the contribution of Cd-d orbitals. The spin asymmetry in the PDOS arises solely from the Eu-f electrons and contributes to the ferromagnetic ground state. For the electronic orbitals involving As and Cd, the PDOS features are spin symmetric.

Optical properties

Optical properties give information about how the material behaves upon incidence of an electromagnetic wave. Understanding the optical response in the visible-light region is particularly important for optoelectronic applications. The study of optical properties of solids has gained considerable attention because of their wide use in modern technologies such as display devices, sensors, lasers, photo detectors, photonics, solar cells, and photo-electrodes. Moreover, optical anisotropy must be considered, as many optical technologies such as displays, polarizers, and wave plates are based on this property. Different energy- or frequency-dependent optical properties, such as the dielectric function, loss function, refractive index, optical conductivity, absorption coefficient, and reflectivity, fully describe how a material responds to incident light [38], [53]. In this study, optical properties for EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} are calculated for photon energies in the range from 0 to 30 eV, and the polarization for the electric field were taken to be in [100] and [1] directions. The computed optical parameters include the dielectric function ε(ω)\varepsilon(\omega), the refractive index n(ω)n(\omega), the optical conductivity κ(ω)\kappa(\omega), the reflectivity R(ω)R(\omega), the absorption coefficient α(ω)\alpha(\omega), and the energy loss function L(ω)L(\omega). Here, ω=2πf\omega= 2\pi f represents the angular frequency. In these calculations, a Drude damping (relaxation energy) value of 0.05 eV and a Gaussian smearing width of 0.5 eV were applied.

Dielectric function: In Figure 16 (a), both real parts and imaginary parts of the dielectric constant under 0, 4, and 8 GPa pressures are plotted. The real part explains the electrical polarization of materials upon incident radiation; on the other hand, the imaginary part shows how dielectric loss varies with the energy of incident radiation. The dielectric function approaches a very low value at about 9.80 eV of incident energy. Beyond about 3.55 eV, the dielectric constant goes to a negative value. So, there is a metallic signature as the dielectric function goes to zero from a negative value. Beyond about 14 eV, the imaginary part of the dielectric constant goes to zero, and the first peak in the loss function is found to be about 14.3 eV. Another noticeable feature is that for very low energy of incident wave, the real part of dielectric function for both polarizations have high value, and as the energy increases, the values of the real part of dielectric functions fall and approach zero beyond about 9.80 eV. The optical anisotropy in the dielectric spectra remains low at all pressures.

Six-panel plots of dielectric function, refractive index, absorption coefficient, optical conductivity, reflectivity, and loss function

Figure 16. (a) Solid lines are for the real part of the dielectric function and dashed lines are the imaginary part of the dielectric function, (b) Solid lines are for the real part of the refractive index, and dashed lines are the imaginary part of the refractive index, (c) Absorption coefficient, (d) Optical conductivity, (e) Reflectivity, and (f) Loss function plot for 0, 4, and 8 GPa.

Refractive Index: The phase velocity of an electromagnetic wave inside a material can be determined by the real part of the refractive index, and how the electromagnetic wave (EMW) attenuates inside the material can be understood from the imaginary part of the refractive index (also known as excitation coefficient). At very low energy, the real part of refractive index has a high value of about 5.62 for both polarizations at every pressure, as shown in Figure 16 (b). This implies no significant optical anisotropy at low energies. There is no significant effect of pressure in this region. With increasing energy, values of the real part decrease and become very low beyond the energy of about 8.82 eV for all pressures. After 15 eV, the real part of the refractive index for both directions starts to increase slightly and reaches a maximum value at about 20.42 eV.

Absorption coefficient: In Figure 16 (c), the absorption coefficient is plotted for both [100] and [1] polarization directions. For both polarization directions, the absorption coefficient starts to increase from the 0 eV which indicates the semimetallic nature of the material. Two peaks are seen in Figure 16 (c); the first peak is observed at the energy of about 6.35eV. From 3.00 eV to 5.71 eV absorption coefficient is large. Its value in visible range is also significant. Thus, this compound is good at absorbing visible light as well as good at absorbing UV light. Beyond this energy, before the next peak, the absorption coefficient has a minimum value at an energy of about 18 eV (for both polarizations). The material is also a good absorber of high energy UV radiation. The absorption coefficient gets to a peak at an energy of about 21.80 eV. In this result, no significant optical anisotropy is observed. The high absorption coefficient in both visible and UV range indicates the potential of the material for optical application. There is significant effect of pressure on the absorption spectra. The compound becomes more absorbing as pressure increases and the peaks show blue shits with rising pressure.

Optical conductivity: The conduction of free charge carriers as a function of the photon energy can be learned from the optical conductivity of a material. This is the dynamic response of free charge carriers in materials, such as an electron or electron-hole pair (for materials with band gap). In Figure 16 (d), it is seen that for [100] polarization the conductivity starts from almost 0 eV for all pressures, indicating no band gap. Initially, optical conductivity increases and get the first peak within an energy range of 2.93 to 4.50 eV for different pressures. Beyond this range, optical conductivity decreases to a low value for both polarizations. Within the range from 4.29 eV to 9.0 eV, optical anisotropy is observed in optical conductivity.

Reflectivity: In Figure 16 (e), the reflectivity as a function of EMW energy is plotted for 0, 4, and 8 GPa. At zero energy and pressure, the reflectivity has the value of about 0.5. At this energy no significant anisotropy in the reflectivity spectra is observed. A peak in reflectivity is observed at about 7.41 eV. This peak is highly sensitive to pressure and grows in magnitude as pressure rises. In the visible and UV region, the compound is found to be a good reflector. At 15 eV, the reflectivity has a low value for both directions of polarization; the first peak in the loss function is also observed near this energy. Beyond about 18.50 eV, the reflectivity starts increasing and then decreases to a very small value at about 30 eV; the second peak in the loss function is observed at about 27.20 eV.

Loss function: The loss function shown in Figure 16 (f) indicating how fast electron will lose energy moving through the material. A peak in the loss function is observed at an energy equivalent to the plasma frequency. In the loss function for zero pressure, we can find the first peak at about 14.30 eV and 13.78 eV for [1] and [100] polarizations, respectively. The second peak is observed at an energy of about 27.20 eV. These energies are equivalent to plasmon energies. The first peak in the loss function for [100] direction shifts slightly to the right with increasing pressure from 0 to 8 GPa, which is an indication of an increment of plasma frequency. Both pressure and electric field polarization have significant effect of the loss function profile.

Conclusions

In this work, we performed a systematic pressure-dependent first-principles DFT study of the structural, elastic, thermophysical, acoustic, electronic and optical properties of EuCd2As2\mathrm{EuCd}_{2}\mathrm{As}_{2} using the GGA-PBE method. The calculated lattice parameters at ambient pressure are in good agreement with the experimentally obtained lattice parameters, confirming the reliability of our computational work. The elastic constants and the calculated mechanical properties reveal that EuCd2As2\mathrm{EuCd_2As_2} meets the Born–Huang stability criterion at all pressures ranging from 0 to 8 GPa, thereby confirming its mechanical stability within this pressure range. The bulk modulus, shear modulus, and Young’s modulus all increased with increasing pressure, indicating that the material progressively stiffened under pressure. At ambient pressure, the relatively low Young’s modulus (74.13 GPa) reflects the soft, layered nature of the crystal structure. Both the Pugh and Poisson’s ratios indicate that EuCd2As2\mathrm{EuCd_2As_2} is brittle under zero pressure becomes ductile under pressures, and that the central interatomic forces govern its structural stability. The machinability index increases with applied pressure. This is a consequence of increased metallicity of the material under pressure. EuCd2As2\mathrm{EuCd_2As_2} possesses small elastic and optical anisotropy. The Debye temperature increases from 233.29 K at 0 GPa to 251.44 K at 8 GPa, which is consistent with pressure-induced hardening. The melting temperature also increases with the applied pressure, from 757.36 K to 944.30 K, this indicates improved thermal stability under compression. The Grüneisen parameter increases with applied pressure. This indicates increment in the lattice anharmonicity. The phonon thermal conductivity decreases with applied pressure. All these demonstrate that pressure is an effective tool for tuning the thermophysical properties of this compound. Acoustic velocity calculations revealed significant anisotropy between the [100] and [1] crystallographic directions, both the longitudinal and transverse velocities increase with applied pressure. In the FM phase, the material remains semimetallic at all studied pressures from 0 to 8 GPa. The density of states analysis indicates that Eu-f, Eu-d, and As-p orbitals contribute strongly to the electronic states near the Fermi level. In the FM phase, the partial density of states of Eu shows an asymmetric distribution between spin-up and spin-down states. As a result, a magnetic moment of 6.96 μB\mu_{\mathrm{B}} per unit cell is obtained. A pseudogap is observed just above the Fermi level in the total density of states. Spin asymmetric density of states around the Fermi level suggests that EuCd2As2\mathrm{EuCd_2As_2} has potential to be used in spintronics. Pressure has notable effect on the band structure and can be used to tune the electronic properties. For example, pressure changes the Fermi surface topology and removes the van Hove singularity feature as shown in Figure 14. The optical properties of EuCd2As2\mathrm{EuCd_2As_2} showed strong absorption within the visible and ultraviolet energy ranges. The high refractive index at low photon energies and broad optical conductivity further support the optoelectronic versatility of the material. The Reflectivity was good in the visible range, whereas from loss function plot plasmon resonances were found at approximately 13–15 eV and 27 eV.

All the physical properties studied are affected by pressure to varying degrees, with variations highly enhanced in the low pressure regime. Overall, this study indicates unambiguously that pressure is a powerful tool for controlling the mechanical, thermal, acoustic, and electronic properties of EuCd2As2\mathrm{EuCd_2As_2}. The pressure induced ductile nature, pressure tunable thermal conductivity, electronic band structure, and strong optical absorption and reflectivity of this compound across a wide energy range indicates that EuCd2As2\mathrm{EuCd_2As_2} is a promising candidate for diverse technological applications.

Data availability

The data sets generated and/or analyzed in this study are available from the corresponding author on reasonable request.

Declaration of interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Declaration of AI usage

The authors used Grammarly, ChatGPT (OpenAI) and Claude AI to improve the language, grammar, sentence structure, and readability of the manuscript. These tools were used solely for language polishing, and the authors take full responsibility for the content, interpretation, and conclusions presented in this paper

Author Contributions

Salauddin Muhammad Anis: Methodology, Software, Formal Analysis, Writing- Original draft. M. A. Afzal: Methodology, Validation, Supervision, Writing-Reviewing and Editing. R. S. Islam: Validation, Supervision, Writing-Reviewing and Editing. S. H. Naqib: Conceptualization, Validation, Supervision, Writing- Reviewing and Editing.

References

  1. [1]N. H. Jo et al., “Manipulating magnetism in the topological semimetal EuCd₂As₂,” Phys. Rev. B, vol. 101, no. 14, p. 140402, Apr. 2020, doi: 10.1103/PhysRevB.101.140402.DOI
  2. [2]I. Schellenberg, U. Pfannenschmidt, M. Eul, C. Schwickert, and R. Pöttgen, “A ¹²¹Sb and ¹⁵¹Eu Mössbauer Spectroscopic Investigation of EuCd₂X₂ (X = P, As, Sb) and YbCd₂Sb₂,” Z. Für Anorg. Allg. Chem., vol. 637, no. 12, pp. 1863–1870, Oct. 2011, doi: 10.1002/zaac.201100179.DOI
  3. [3]N. H. Jo et al., “Manipulating of magnetism in the topological semimetal EuCd₂As₂,” 2020, doi: 10.48550/ARXIV.2002.10485.DOI
  4. [4]S. Roychowdhury et al., “Anomalous Hall Conductivity and Nernst Effect of the Ideal Weyl Semimetallic Ferromagnet EuCd₂As₂,” Adv. Sci., vol. 10, no. 13, p. 2207121, May 2023, doi: 10.1002/advs.202207121.DOI
  5. [5]J.-Z. Ma et al., “Spin fluctuation induced Weyl semimetal state in the paramagnetic phase of EuCd₂As₂,” Sci. Adv., vol. 5, no. 7, p. eaaw4718, Jul. 2019, doi: 10.1126/sciadv.aaw4718.DOI
  6. [6]M. C. Rahn et al., “Coupling of magnetic order and charge transport in the candidate Dirac semimetal EuCd₂As₂,” Phys. Rev. B, vol. 97, no. 21, p. 214422, Jun. 2018, doi: 10.1103/PhysRevB.97.214422.DOI
  7. [7]D. Santos-Cottin et al., “EuCd₂As₂ : A Magnetic Semiconductor,” Phys. Rev. Lett., vol. 131, no. 18, p. 186704, Nov. 2023, doi: 10.1103/PhysRevLett.131.186704.
  8. [8]S. Nasrallah et al., “Magneto-optical response of the magnetic semiconductors EuCd₂X₂ (X =P, As, Sb),” Phys. Rev. B, vol. 110, no. 20, p. L201201, Nov. 2024, doi: 10.1103/PhysRevB.110.L201201.DOI
  9. [9]J. Krishna, T. Nautiyal, and T. Maitra, “First-principles study of electronic structure, transport, and optical properties of EuCd₂As₂,” Phys. Rev. B, vol. 98, no. 12, p. 125110, Sep. 2018, doi: 10.1103/PhysRevB.98.125110.DOI
  10. [10]J. Krishna, M. Sharma, and T. Maitra, “Anisotropic thermoelectric properties of EuCd₂As₂: An Ab-initio study,” Jul. 31, 2019, arXiv: arXiv:1907.13446. doi: 10.48550/arXiv.1907.13446.
  11. [11]K. M. Taddei et al., “Single pair of Weyl nodes in the spin-canted structure of EuCd₂As₂,” Phys. Rev. B, vol. 105, no. 14, p. L140401, Apr. 2022, doi: 10.1103/PhysRevB.105.L140401.DOI
  12. [12]K. Taddei et al., “Spin-canting driven Weyl physics in EuCd₂As₂,” arXiv preprint arXiv:2012.01555.
  13. [13]J. P. Perdew, K. Burke, and M. Ernzerhof, “Generalized Gradient Approximation Made Simple,” Phys. Rev. Lett., vol. 77, no. 18, pp. 3865–3868, Oct. 1996, doi: 10.1103/PhysRevLett.77.3865.DOI
  14. [14]S. J. Clark et al., “First principles methods using CASTEP,” Z. Für Krist. - Cryst. Mater., vol. 220, no. 5–6, pp. 567–570, May 2005, doi: 10.1524/zkri.220.5.567.65075.DOI
  15. [15]H. J. Monkhorst and J. D. Pack, “Special points for Brillouin-zone integrations,” Phys. Rev. B, vol. 13, no. 12, pp. 5188–5192, Jun. 1976, doi: 10.1103/PhysRevB.13.5188.DOI
  16. [16]T. H. Fischer and J. Almlöf, “General methods for geometry and wave function optimization,” J. Phys. Chem., vol. 96, no. 24, pp. 9768–9774, Nov. 1992, doi: 10.1021/j100203a036.DOI
  17. [17]P. Giannozzi et al., “QUANTUM ESPRESSO: a modular and open-source software project for quantum simulations of materials,” J. Phys. Condens. Matter, vol. 21, no. 39, p. 395502, Sep. 2009, doi: 10.1088/0953-8984/21/39/395502.DOI
  18. [18]G. Prandini et al., “A Standard Solid State Pseudopotentials (SSSP) library optimized for precision and efficiency.” Materials Cloud, p. 35589539075, Apr. 13, 2023. doi: 10.24435/MATERIALSCLOUD:F3-YM.DOI
  19. [19]K. Momma and F. Izumi, “VESTA 3 for three-dimensional visualization of crystal, volumetric and morphology data,” J. Appl. Crystallogr., vol. 44, no. 6, pp. 1272–1276, Dec. 2011, doi: 10.1107/S0021889811038970.DOI
  20. [20]M. De Jong et al., “Charting the complete elastic properties of inorganic crystalline compounds,” Sci. Data, vol. 2, no. 1, p. 150009, Mar. 2015, doi: 10.1038/sdata.2015.9.DOI
  21. [21]J. Gao, Q.-J. Liu, and B. Tang, “Elastic stability criteria of seven crystal systems and their application under pressure: Taking carbon as an example,” J. Appl. Phys., vol. 133, no. 13, p. 135901, Apr. 2023, doi: 10.1063/5.0139232.DOI
  22. [22]C.-F. Yu and Y.-L. Liu, “DFT Study of Au₃In and Au₃In₂ Intermetallic Compounds: Structural Stability, Fracture Toughness, Anisotropic Elasticity, and Thermophysical Properties for Advanced Applications,” Materials, vol. 18, no. 7, p. 1561, Mar. 2025, doi: 10.3390/ma18071561.DOI
  23. [23]W. Voigt, “Ueber die Beziehung zwischen den beiden Elasticitätsconstanten isotroper Körper,” Ann. Phys., vol. 274, no. 12, pp. 573–587, Jan. 1889, doi: 10.1002/andp.18892741206.DOI
  24. [24]A. Reuss, “Berechnung der Fließgrenze von Mischkristallen auf Grund der Plastizitätsbedingung für Einkristalle .,” ZAMM - J. Appl. Math. Mech. Z. Für Angew. Math. Mech., vol. 9, no. 1, pp. 49–58, Jan. 1929, doi: 10.1002/zamm.19290090104.DOI
  25. [25]R. Hill, “The Elastic Behaviour of a Crystalline Aggregate,” Proc. Phys. Soc. Sect. A, vol. 65, no. 5, pp. 349–354, May 1952, doi: 10.1088/0370-1298/65/5/307.DOI
  26. [26]X. Wang, H. Xiang, X. Sun, J. Liu, F. Hou, and Y. Zhou, “Mechanical Properties and Damage Tolerance of Bulk Yb₃Al₅O₁₂ Ceramic,” J. Mater. Sci. Technol., vol. 31, no. 4, pp. 369–374, Apr. 2015, doi: 10.1016/j.jmst.2015.01.002.
  27. [27]S. F. Pugh, “XCII. Relations between the elastic moduli and the plastic properties of polycrystalline pure metals,” Lond. Edinb. Dublin Philos. Mag. J. Sci., vol. 45, no. 367, pp. 823–843, Aug. 1954, doi: 10.1080/14786440808520496.DOI
  28. [28]G. N. Greaves, A. L. Greer, R. S. Lakes, and T. Rouxel, “Erratum: Poisson’s ratio and modern materials,” Nat. Mater., vol. 10, no. 12, pp. 986–986, Dec. 2011, doi: 10.1038/nmat3177.DOI
  29. [29]P. H. Mott, J. R. Dorgan, and C. M. Roland, “The bulk modulus and Poisson’s ratio of ‘incompressible’ materials,” J. Sound Vib., vol. 312, no. 4–5, pp. 572–575, May 2008, doi: 10.1016/j.jsv.2008.01.026.DOI
  30. [30]H. Fu, D. Li, F. Peng, T. Gao, and X. Cheng, “Ab initio calculations of elastic constants and thermodynamic properties of NiAl under high pressures,” Comput. Mater. Sci., vol. 44, no. 2, pp. 774–778, Dec. 2008, doi: 10.1016/j.commatsci.2008.05.026.DOI
  31. [31]Z. Sun, D. Music, R. Ahuja, and J. M. Schneider, “Theoretical investigation of the bonding and elastic properties of nanolayered ternary nitrides,” Phys. Rev. B, vol. 71, no. 19, p. 193402, May 2005, doi: 10.1103/PhysRevB.71.193402.DOI
  32. [32]D. Connétable, “First-principles study of transition metal carbides,” Mater. Res. Express, vol. 3, no. 12, p. 126502, Dec. 2016, doi: 10.1088/2053-1591/3/12/126502.DOI
  33. [33]Y. H. Duan, Y. Sun, M. J. Peng, and S. G. Zhou, “Anisotropic elastic properties of the Ca–Pb compounds,” J. Alloys Compd., vol. 595, pp. 14–21, May 2014, doi: 10.1016/j.jallcom.2014.01.108.DOI
  34. [34]C. M. Kube and M. De Jong, “Elastic constants of polycrystals with generally anisotropic crystals,” J. Appl. Phys., vol. 120, no. 16, p. 165105, Oct. 2016, doi: 10.1063/1.4965867.DOI
  35. [35]S. I. Ranganathan and M. Ostaja-Starzewski, “Universal Elastic Anisotropy Index,” Phys. Rev. Lett., vol. 101, no. 5, p. 055504, Aug. 2008, doi: 10.1103/PhysRevLett.101.055504.DOI
  36. [36]F. W. Vahldiek and S. A. Mersol, Eds., Anisotropy in Single-Crystal Refractory Compounds: Proceedings of an International Symposium on Anisotropy in Single-Crystal Refractory Compounds, held on June 13–15, 1967, in Dayton Ohio. Sponsored by the Ceramics and Branch of the air Force Materials Laboratory, United States Air Force. Boston, MA: Springer US, 1968. doi: 10.1007/978-1-4899-5307-0.DOI
  37. [37]D. H. Chung and W. R. Buessam, “The Elastic Anisotropy of Crystals,” J. Appl. Phys., vol. 38, no. 5, pp. 2010–2012, Apr. 1967, doi: 10.1063/1.1709819.DOI
  38. [38]I. Ahmed, F. Parvin, R. S. Islam, and S. H. Naqib, “Ab-initio insights into the mechanical, phonon, bonding, electronic, optical and thermal properties of hexagonal W₂N₃ for prospective applications,” Heliyon, vol. 10, no. 13, p. e33613, Jul. 2024, doi: 10.1016/j.heliyon.2024.e33613.DOI
  39. [39]M. I. Naher and S. H. Naqib, “Structural, elastic, electronic, bonding, and optical properties of topological CaSn₃ semimetal,” J. Alloys Compd., vol. 829, 154509, 15 Jul. 2020, doi: 10.1016/j.jallcom.2020.154509.DOI
  40. [40]R. Gaillac, P. Pullumbi, and F.-X. Coudert, “ELATE: an open-source online application for analysis and visualization of elastic tensors,” J. Phys. Condens. Matter, vol. 28, no. 27, p. 275201, Jul. 2016, doi: 10.1088/0953-8984/28/27/275201.DOI
  41. [41]O. L. Anderson, “A simplified method for calculating the debye temperature from elastic constants,” J. Phys. Chem. Solids, vol. 24, no. 7, pp. 909–917, Jul. 1963, doi: 10.1016/0022-3697(63)90067-2.DOI
  42. [42]M. E. Fine, L. D. Brown, and H. L. Marcus, “Elastic constants versus melting temperature in metals,” Scr. Metall., vol. 18, no. 9, pp. 951–956, Sep. 1984, doi: 10.1016/0036-9748(84)90267-9.DOI
  43. [43]J. R. Davis, Ed., “Engineering Data for Metals and Alloys,” in Metals Handbook Desk Edition, 2nd ed., ASM International, 1998, pp. 64–84. doi: 10.31399/asm.hb.mhde2.a0003082.DOI
  44. [44]G. Slack, “Solid-State Physics Vol. 34, edited by F. Seitz, D. Turnbull and H. Ehrenreich,” 1979.
  45. [45]M. I. Naher, A. F. M. Yusuf Haider, D. K. Paul, M. L. Rahman, Feroze H. Haque, and S. H. Naqib, "First-principles investigation of the pressure dependent physical properties of intermetallic kagome ZrRe₂," Sci Rep (2026). https://doi.org/10.1038/s41598-026-73976-9
  46. [46]C. L. Julian, “Theory of Heat Conduction in Rare-Gas Crystals,” Phys. Rev., vol. 137, no. 1A, pp. A128–A137, Jan. 1965, doi: 10.1103/PhysRev.137.A128.DOI
  47. [47]M. A. Alam, M. A. H. Shah, F. Parvin, and S. H. Naqib, “Physical Properties of Transition Metal Hydride Superconductors Mg₂TmH₆ (Tm = Rh, Pd, Ir, Pt) by First-Principles Calculations,” Adv. Phys. Res., p. e70192, Sep. 2026, doi: 10.1002/apxr.70192.DOI
  48. [48]E. Schreiber, O. L. Anderson, N. Soga, and J. F. Bell, “Elastic Constants and Their Measurement,” J. Appl. Mech., vol. 42, no. 3, pp. 747–748, Sep. 1975, doi: 10.1115/1.3423687.DOI
  49. [49]P. Li, L. Ma, M. Peng, B. Shu, and Y. Duan, “Elastic anisotropies and thermal conductivities of WB₂ diborides in different crystal structures: A first-principles calculation,” J. Alloys Compd., vol. 747, pp. 905–915, May 2018, doi: 10.1016/j.jallcom.2018.03.109.DOI
  50. [50]Razu Ahmed, Md. Mahamudujjaman, Md. Asif Afzal, Md. Sajidul Islam, R. S. Islam, and S. H. Naqib, "DFT based comparative analysis of the physical properties of some binary transition metal carbides XC (X = Nb, Ta, Ti)," Journal of Materials Research and Technology, vol. 24, pp. 4808 - 4832, May-June 2023, doi: 10.1016/j.jmrt.2023.04.147.DOI
  51. [51]M. I. Naher, M. Mahamudujjaman, A. Tasnim, R. S. Islam, and S. H. Naqib, " AbstAb-initio insights into the elastic, bonding, phonon, optoelectronic and thermophysical properties of SnTaS₂," Solid State Sciences, vol. 131, 106947, Sept. 2022, doi: 10.1016/j.solidstatesciences.2022.106947.DOI
  52. [53]B. Rahman Rano, Ishtiaque M. Syed, and S. H. Naqib, " Elastic, electronic, bonding, and optical properties of WTe₂ Weyl semimetal: A comparative investigation with MoTe₂ from first principles", Results in Physics, vol. 19, 103639, December 2020, https://doi.org/10.1016/j.rinp.2020.103639

Paper details

vlnc:W_xwhtpa55
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Grammarly, ChatGPT (OpenAI), Claude AI

View statement
Looking for related papers…
Contents