betaFeedback

WorksComputer Science

Suspended-Fabric Robotic Manipulation Surfaces: Modelling, Design Space, and Multimodular Extensio

Abstract

Robotic Manipulation Surfaces (RMS) reposition objects by deforming the surface on which they rest. A recent class of RMS suspends a continuous fabric sheet from a sparse grid of vertical linear actuators lowering the actuator density of such surfaces but how to design such surfaces so that objects can be controlled everywhere on it, and how to extend it beyond a single module so that objects can pass between modules and achieve parallel, remain open. This paper presents a separable catenary model of the suspended sheet that is fast to compute and provides both the surface shape for given actuator heights and the actuator heights for a desired local slope. The closed form inverse lets a simple PID controller position objects on the sheet, and the model relates fabric length, module span and actuator stroke to the reachable workspace, yielding a minimum fabric length bound and design charts for these surfaces. The approach is then extended to a multimodular platform in which neighbouring modules share actuators. On a 2×22 \times 2 prototype, we demonstrate that centimetre-scale objects are transferred between modules and positioned within 0.03 m over a 1m21 m^2 workspace with only nine actuators, enabling multi-object manipulation and opening the way to parallel manipulation.

Introduction

Food processing, logistics and warehouse automation require large numbers of heterogeneous and often fragile objects to be repositioned over extended work areas. Pick and place manipulators handle such objects sequentially, which limits throughput and risks damaging delicate items, while conveyor belts provide throughput but only unidirectional transport. Robotic Manipulation Surfaces (RMS) follow a different strategy: rather than grasping an object, they deform or actuate the surface on which the object rests, and the resulting distributed contact allows safe and parallel handling of diverse items without object specific end effectors. Established RMS designs, such as arrays of rollers [1], vertical pistons [2] or linear delta robots [3], obtain fine control through high actuator density: ArrayBot drives 256 pistons at a 20 mm pitch, about 2500 actuators per square metre, and the delta array of [3] actuates 192 degrees of freedom over an 8×88 \times8 grid. Such density limits the workspace that can be built and maintained in practice.

Some RMS decouple control resolution from actuator density by covering a sparse set of actuators with a continuous elastic layer that deforms between them. Festo’s wave handling surface [4] placed such a layer over a grid of pneumatic actuators and Morpho [5] used membrane deformation to transfer objects between modules, both demonstrated with rolling objects only. A fabric sheet suspended from four vertical linear actuators at the corners of a 0.50.5 m square module (16 actuators/m2\mathrm{m}^2) has been shown to manipulate fragile and irregular objects at an object to actuator size ratio as low as 0.010.01 [6], using a geometric transformation combined with a PID controller [7].

A parallel line of work manipulates objects on a deformable sheet whose supports are themselves mobile. Early work repositioned a rigid body on a flexible sheet for an automated rehabilitation bed [8]. Subsequently, a team of mobile robots holding a sheet has been used to transport and manipulate carried objects, described either through the strain energy of an elastic membrane [9] or through the virtual variable cables model (VVCM), which replaces the sheet by a set of dynamically changing cables [10] and has been extended to stable kinematics for arbitrary team formations [11]. Both descriptions serve as baselines in Section IV-A. Hanging cloth itself has been modelled by fitting catenary curves between the constraint points and relaxing the result [12], whereas membrane models that resolve the taut, wrinkled and slack states of a sheet require numerical solution [13].

In summary, existing deformable sheet and cloth models [8, 9, 10, 11, 12, 13] give the shape of a sheet for given support positions, but none maps a desired local slope at the object directly to the heights of four vertical supports in the closed form that an online controller requires. In addition, the design of this type of RMS is challenging, as no analytical link relates fabric slack, module size and actuator stroke to the workspace over which an object can be held, so these parameters have been chosen by trial and error. Finally, extending the surface beyond one module without a high actuator count requires neighbouring modules to share actuators, which couples them mechanically, and no route to large area scaling under that coupling has been shown.

This paper expands previous work on suspended fabric RMS and provides three contributions toward extensible, large area object manipulation with sparse actuation.

A simplified fabric model with an analytical inverse. The fabric is modelled as a separable catenary whose single sag parameter is fixed by fabric length and module span, giving the surface shape for given actuator heights and the actuator heights for a desired local slope in closed form. The low computational cost and the inverse kinematics of the model allow it to be used in online controllers, which improves the available workspace of the system.

Design conditions for suspended fabric surfaces. Because the model depends on fabric slack, module span and actuator stroke, the trade off between these three parameters is analysed in closed form, yielding a minimum fabric length bound and reachable workspace charts from which the conditions that maximise the workspace are read directly.

Extension to a multimodular surface. The suspended fabric approach is extended to a multimodular prototype with shared actuators, demonstrating transfer and positioning of heterogeneous objects across modules while characterising the inter module coupling that actuator sharing introduces. Such a surface could, for example, be spread under an orchard tree to catch shaken fruit and convey it undamaged to one module for packing.

Platform and Simulation

Hardware

The prototype (Figure 1) consists of nine linear actuators on a scissor frame that sets their spacing; at the 0.50.5 m spacing used here they form a 2×22 \times2 grid of modules of span D=0.5D = 0.5 m (§ 7) resting at 0.70.7 m. Each actuator is stepper driven with 12 bit encoder feedback, has a stroke of 0.40.4 m, and is commanded within ±umax⁡=0.16\pm u_{\max} = 0.16 m of the resting height throughout. The surface is a 1.2×1.21.2 \times1.2 m polyester sheet, giving S=0.6S = 0.6 m of material across each 0.50.5 m module span. Objects are tracked by a six camera OptiTrack system at 120 Hz.

Multimodular soft manipulation surface

Figure 1. Multimodular soft manipulation surface. (A) Physical platform during manipulation of a spherical object. (B) Top view of the nine actuators (A0 to A8) and the four modules (M0 to M3) with the fabric removed. Adjacent modules share two actuators and diagonal modules share one. (C) MuJoCo model of the 2×22 \times2 configuration showing an object (green sphere) and its target location (blue cylinder).

Simulation Environment

MuJoCo [14] is used for simulation. The fabric is a flexcomp mesh with the membrane elasticity plugin (Young modulus 3 kPa, Poisson ratio 0.3, thickness 1 mm), which resists stretching but not bending; the corner vertices are fixed to prismatic actuators and the solver uses an implicit fast integrator at 1 ms. A single module is a 15×1515 \times15 mesh at 35 mm spacing, material covers the 0.50.5 m pitch, so the simulated sheet is in tension where the physical sheet is slack; the 2×22 \times2 layout of Figure 1C is a 21×2121 \times21 mesh at 49 mm and is used only for the end to end trials of § 7-A. All other simulation results use the single module, whose fidelity to the physical fabric is assessed in Section IV-A.

Separable Catenary Surface Model

The model treats the fabric as a uniform and inextensible sheet that hangs under its own weight between supports, so that each cross section adopts the classical catenary profile. Three consequences follow. The profile is governed by a single scalar sag parameter rather than by the elastic constants of the material. Local indentation caused by the mass of the carried object is not represented. Cross axis coupling is neglected, since the two axes are treated as independent. The error/cost of these assumptions are measured empirically in Section IV-A.

Single Axis Catenary

The cross sectional profile of a sheet suspended between two points is

z(x)=acosh⁡(x−x0a)(1)z(x) = a \cosh\left(\frac{x-x_0}{a}\right) \tag*{(1)}

where a>0a > 0 is the sag parameter, with larger aa producing a flatter profile, and x0x_0 is the horizontal position of the vertex. The slope is

dzdx=sinh⁡(x−x0a)(2)\frac{d z}{d x} = \sinh\left(\frac{x-x_0}{a}\right) \tag*{(2)}

For the curve to be usable as a control model, the vertex must be placed so that the slope at the target position xtx_t equals a commanded value mm. Setting dz/dx∣xt=md z/d x|_{x_t} = m in (2)

dzdx∣xt=m\frac{d z}{d x}\bigg|_{x_t} = m

gives

x0=xt−aarcsinh⁡(m).(3)x_0=x_t-a\operatorname{arcsinh}(m). \tag*{(3)}

The controller requires corner heights relative to the target, so h(x)=z(x)−z(xt)h(x)=z(x)-z(x_t) is defined. Substituting (3) into (1) and using cosh⁡(arcsinh⁡(m))=1+m2\cosh(\operatorname{arcsinh}(m))=\sqrt{1+m^2} yields z(xt)=a1+m2z(x_t)=a\sqrt{1+m^2} and therefore

h(x)=acosh⁡(x−x0a)−a1+m2,(4)h(x)=a\cosh\left(\frac{x-x_0}{a}\right)-a\sqrt{1+m^2}, \tag*{(4)}

which satisfies h(xt)=0h(x_t)=0 by construction. The surface height at the target is the reference datum, and corners above or below that level receive positive or negative heights accordingly.

Sag Parameter and Minimum Fabric Length

The sag parameter relates the fabric length to the module span. For a catenary spanning a horizontal distance DD, the arc length is

S=2asinh⁡(D2a).(5)S=2a\sinh\left(\frac{D}{2a}\right). \tag*{(5)}

When S=DS=D the sheet is taut and a→∞a\to\infty, producing a straight line. As SS grows beyond DD the sheet develops slack, aa decreases and the profile sags more deeply, which widens the range of achievable slopes but increases the actuator displacement needed to produce them. For the platform of § 2, with S=0.6 mS=0.6\ \mathrm{m} and D=0.5 mD=0.5\ \mathrm{m}, numerical solution of (5) gives a=0.235 ma=0.235\ \mathrm{m}.

A geometric lower bound on the fabric length follows from the requirement that the sheet must still connect adjacent actuators when they sit at opposite extremes of their range. With one actuator raised to +umax⁡+u_{\max} and its neighbour lowered to −umax⁡-u_{\max}, the material must bridge a horizontal distance DD and a vertical distance 2umax⁡2u_{\max}, so that

Smin⁡=D2+4umax⁡2.(6)S_{\min}=\sqrt{D^2+4u_{\max}^2}. \tag*{(6)}

At S=Smin⁡S=S_{\min} the full actuator range is available; further slack reduces the fraction of actuator displacement converted into surface slope. For D=0.5 mD=0.5\ \mathrm{m} and umax⁡=0.16 mu_{\max}=0.16\ \mathrm{m}, (6) gives Smin⁡=0.594 mS_{\min}=0.594\ \mathrm{m}, so the fabric length of the platform sits marginally above the bound.

Separable Surface and Corner Heights

The surface of one module is modelled as the sum of two independent cross sections, one per axis (Figure 2):

Separable catenary surface model on a single module

Figure 2. Separable catenary surface model on a single module. (a) Single axis catenary of (1) to (5) between the supports of one module: the vertex at x0x_0 lies aa above the directrix, the commanded slope mm is the tangent at the target xtx_t, and the corner heights h(cjx)h(c_j^x) are measured from the datum h(xt)=0h(x_t)=0. The fabric length SS and the module span DD fix aa through (5). (b) Minimum fabric length of (6). (c) Surface of (7) as the sum of the two cross sections through pt=(xt,yt)p_t=(x_t,y_t), with the corner heights qˉj\bar{q}_j of (8) measured from the mean plane (dashed) and the error vector e\mathbf{e} driving the controller of § 5-A.

z(x,y)=h(x;ax,mx,xt)+h(y;ay,my,yt),(7)z(x,y)=h(x;a_x,m_x,x_t)+h(y;a_y,m_y,y_t), \tag*{(7)}

where (xt,yt)(x_t,y_t) is the target position. This decomposition matches the four corner actuator layout, which provides two independent tilt axes. For an actuator corner jj at position cj=(cjx,cjy)\mathbf{c}_j=(c_j^x,c_j^y) the desired height is qj=h(cjx)+h(cjy)q_j=h(c_j^x)+h(c_j^y). The four heights share a nonzero common offset that would translate the surface vertically without altering its slope, so the mean is removed to devote the full stroke to shaping:

qˉj=qj−1N∑k=1Nqk.(8)\bar{q}_j=q_j-\frac{1}{N}\sum_{k=1}^{N}q_k. \tag*{(8)}

Surface Model Validation

For validation, the catenary is compared with a planar interpolant of the support heights, as used by the baseline controller [7], the VVCM [10] in the stable kinematics formulation of [11] generalised to unequal support heights, and the isotropic membrane strain energy model of [9]. The comparison covers surface shape, object equilibrium prediction and computational cost, and the catenary is further checked under object loading.

Height and Slope Error

Two surface references are used: simulation and hardware. The simulated reference is the single 0.5 m0.5\ \mathrm{m} pitch module MuJoCo membrane of § 2. The hardware-measured reference is a 7×77\times7 grid of retroreflective markers bonded at 0.1 m0.1\ \mathrm{m} spacing to the fabric of one module and recovered by motion capture. A thin plate spline through the 49 tracked markers, smoothed gives the measured surface, and every model is scored against it on a 41×4141\times41 grid over the support square, so the whole sheet is judged rather than the marker positions alone. The height error ϵz\epsilon_z is the RMS height difference after the mean height is removed from both surfaces, the vertical datum of a capture being arbitrary; the slope error ϵv\epsilon_v is the RMS norm of the difference between predicted and measured surface gradients. Three captures are taken on each reference with identical support commands: the command of Figure 3, which raises one support 82.5 mm above the mean and lowers the other three by 27.5 mm, and two near the resting height. On hardware the marker grid extends beyond the 0.5 m support square, and only the region inside the square is scored.

Surface models and signed height errors for the measured fabric and four models

Figure 3. Surface models against the measured fabric for the command [+82.5,−27.5,−27.5,−27.5][+82.5, -27.5, -27.5, -27.5] mm. Top: the surface fitted through the 49 tracked markers (red dots) and the four model surfaces. Bottom: the applied command, then each model’s signed height error over the support square; small dots mark the marker lattice, large dots the supports.

ModelSimulationHardware
ϵz\epsilon_z [mm]ϵ∇\epsilon_{\nabla}ϵz\epsilon_z [mm]ϵ∇\epsilon_{\nabla}
Command of Fig. 3, [+82.5,−27.5,−27.5,−27.5][+82.5, -27.5, -27.5, -27.5] mm
Planar39.40.3750.90.67
Catenary15.90.2329.10.41
VVCM30.90.3349.90.65
Membrane energy6.50.0829.10.42
Three configurations, mean ±\pm sd
Planar41.5±2.741.5 \pm2.70.40±0.030.40 \pm0.0359.2±6.859.2 \pm6.80.63±0.030.63 \pm0.03
Catenary15.4±0.515.4 \pm0.50.19±0.040.19 \pm0.0443.6±12.443.6 \pm12.40.44±0.080.44 \pm0.08
VVCM31.9±1.931.9 \pm1.90.32±0.030.32 \pm0.0363.1±12.063.1 \pm12.00.65±0.090.65 \pm0.09
Membrane energy7.7±2.17.7 \pm2.10.11±0.020.11 \pm0.0244.2±15.144.2 \pm15.10.47±0.090.47 \pm0.09

Table I. Height error ϵz\epsilon_z (mm) and slope error ϵ∇\epsilon_{\nabla} (dimensionless) of the four models. Top: the single command of Figure 3, one RMS value per model. Bottom: mean ±\pm sd over the three support configurations.

Table I and Figure 3 give the result. On the slack physical sheet the catenary matches the best model, the membrane energy model, on height error (29.1 mm for both, a factor 1.7 below the planar interpolant and the VVCM) and has the lowest slope error of the four, with one scalar and no numerical solution. On the simulated membrane the membrane energy model is more accurate (6.5 against 15.9 mm), the price of the catenary’s simplicity, but the catenary is more accurate than the VVCM on both references and, as Section IV-D shows, far cheaper than either. The four models rank the same on the simulated membrane as on the fabric, so a result obtained in simulation in § 5 transfers qualitatively to hardware. All four models share one error pattern (Figure 3): too shallow at the centre and too low near the supports, where the slack sheet, which continues beyond

the support square, runs straighter into the supports than any of the models.

Equilibrium Prediction

A second test is where an object comes to rest. The five objects of Table II are placed at rest at random positions on the simulated membrane under 40 random corner configurations each and left to settle without control, and the settled position is compared with the minimum of each model’s surface; the planar interpolant has no minimum and is excluded. The catenary is closest for every object, within 7 to 15% of the module span, and its error grows least from the sphere to the flat disk. The VVCM matches it for the sphere, the point mass its derivation assumes, and falls behind for every other shape. The membrane energy model, best on height, is worst here because its surface is nearly flat around the minimum, so the position of the minimum is poorly determined and a small height error moves it by several centimetres.

Object (mass, size in cm)MotionCatenaryVVCMMembrane
Sphere (32 g, ∅\varnothing4.5)rolling7.18.318.4
Egg (61 g, ∅\varnothing4.1 to 6.2)rolling8.814.625.5
Cube (31 g, 4.2)mixed14.921.733.2
Cylinder (71 g, ∅\varnothing3 ×\times 13)mixed12.115.625.3
Disk (26 g, ∅\varnothing7 ×\times 2.5)sliding14.320.131.4

Table II. Test objects and normalised equilibrium error eˉ=ep/D\bar{e} = e_p/D in %, where epe_p is the mean distance in simulation between the settled object position and the minimum of each model’s surface, over 40 corner configurations per object.

Validity Under Object Loading

To assess the sensitivity of the unloaded surface approximation to object loading, the fabric is captured with all actuators at their resting height, without an object, with a 50.3 g object representative of those manipulated in this paper, and with a 300 g object as a heavier stress case, each placed at the module centre or 0.17 m from it. At rest the actuators sit at their calibrated zero, and the sag parameter fitted on six unloaded captures, α=0.248\alpha= 0.248 m, is within 6% of the geometric value; it is held fixed for the loaded captures. The representative load sinks the sheet by 24 mm at the centre and raises the catenary height error from 12 to 17 mm; the stress case sinks it by 42 mm and raises the error to 24 mm. Refitting aa to each loaded capture recovers at most 3 mm of this error, so most of the degradation is load induced deformation that changing the sag parameter alone cannot represent. Placed off centre, either load lowers the sheet mostly near the centre, a global shift rather than a local pocket, and leaves the height error within 1.3 mm of the unloaded value. For the objects of this paper, 26 to 71 g, the unloaded catenary therefore holds to within 5 mm of height error. Under a payload an order of magnitude heavier the sheet is no longer an exact catenary, but exact reconstruction of the loaded surface is not required for control: the model is expected to remain usable as an approximate local slope model for generating actuator commands.

ModelComplexityN=4N=4N=9N=9N=16N=16Inverse
PlanarO(N)O(N)0.020.040.0620 μs20\,\mu\mathrm{s}
CatenaryO(N)O(N)6.99.39.820 μs20\,\mu\mathrm{s}
VVCM, general zjz_jO(T(N) poly K)O(T(N)\ \mathrm{poly}\ K)18.427676.1×1056.1\times10^5none
VVCM, uniform zrz_rO(T(N) K3)O(T(N)\ K^3)0.1725.53140none
Membrane energyO(iters⋅M)O(\mathrm{iters}\cdot M)240488675none

Table III. Cost of one forward evaluation per model on rigs of NN supports. T(N)=∑K=3N(NK)T(N)=\sum_{K=3}^{N}\binom{N}{K} is the number of VVCM taut sets (5, 466 and 65 399); MM the number of mesh nodes (225, 441 and 625). Inverse: cost of the closed form map from commanded slope to support heights. *Extrapolated from the measured per set cost.

Computational Cost

tbl:III gives the cost of one forward evaluation of each model on rigs of N={4,9,16}N=\{4,9,16\} supports in a single threaded Python implementation; the scaling, not the absolute time, is the result. The planar and catenary models are linear in NN, and their inverse, the closed form map (3) to (8) from a commanded slope to the four support heights, costs under 20 μs20\,\mu\mathrm{s}, which is what lets the model run inside the loop; the catenary forward time in the table is dominated by locating the surface minimum, which the controller never needs. The VVCM enumerates every taut set, so its cost grows as 2N2^N from 18 ms at N=4N=4 to 2.8 s at N=9N=9, and the closed form of [11] applies only to supports at one height. The membrane energy model minimises a finite element energy over the mesh at about 1.1 ms per node. Neither has an inverse: the VVCM returns an equilibrium point rather than a slope field, and the membrane model defines slope only after minimisation.

Catenary Position Controller

The model is validated in closed loop by replacing the geometric transformation of the planar baseline [7], which maps PID tilt angles to actuator heights through the point normal equation of a plane, with (4) to (8). Control acts on one module at a time through its four corner actuators at 60 Hz; Algorithm 1 gives one step.

Controller

A PID controller with velocity damping acts on each axis of the position error and outputs a commanded slope (line

Algorithm 1 Catenary controller, one control step.

Require: error ee, velocity vv, target pt\mathbf{p}_t, corners {cj}j=14\{c_j\}_{j=1}^{4}

  1. for each axis i∈{x,y}i\in\{x,y\} do

  2. Ii←sat⁡Imax⁡(Ii+eiΔt),e˙i←(ei−eik−1)/ΔtI_i\leftarrow\operatorname{sat}_{I_{\max}}(I_i+e_i\Delta t),\quad\dot e_i\leftarrow(e_i-e_i^{k-1})/\Delta t

  3. miraw←−(Kpei+KiIi+Kde˙i)+Kvvim_i^{\mathrm{raw}}\leftarrow-(K_p e_i+K_i I_i+K_d\dot e_i)+K_vv_i

  4. mi←αsat⁡mmax⁡(miraw)+(1−α)mik−1m_i\leftarrow\alpha\operatorname{sat}_{m_{\max}}(m_i^{\mathrm{raw}})+(1-\alpha)m_i^{k-1}

  5. end for

  6. qj←h(cjx;ax,mx,pt,x)+h(cjy;ay,my,pt,y)∀jq_j\leftarrow h(c_j^x;a_x,m_x,p_{t,x})+h(c_j^y;a_y,m_y,p_{t,y})\quad\forall j

  7. qˉj←qj−mean⁡(q)∀j\bar q_j\leftarrow q_j-\operatorname{mean}(q)\quad\forall j

  8. uj←sat⁡umax⁡(qˉj+αvδj),δj∼U(−1,1)∀ju_j\leftarrow\operatorname{sat}_{u_{\max}}(\bar q_j+\alpha_v\delta_j),\quad\delta_j\sim U(-1,1)\quad\forall j

3), saturated and low pass filtered (line 4) before (4) and (8) convert it into corner heights (lines 6 and 7). The velocity term, fed by the tracking system, adds a counter slope as the object approaches the target and limits overshoot near edges and corners where objects gain speed; the vibration term αvδj\alpha_v\delta_j dislodges non spherical objects that settle into fabric indentations and is 0.05 m for sliding and mixed objects and zero for rolling ones. The gains, tuned by a genetic algorithm on the integrated absolute error of target reaching trials in simulation, are Kp=3.71 m−1K_p=3.71\,\mathrm{m}^{-1}, Ki=1.81 m−1s−1K_i=1.81\,\mathrm{m}^{-1}\mathrm{s}^{-1}, Kd=0.86 s m−1K_d=0.86\,\mathrm{s}\,\mathrm{m}^{-1} and Kv=1.05 s m−1K_v=1.05\,\mathrm{s}\,\mathrm{m}^{-1}, with Imax⁡=1.0 m sI_{\max}=1.0\,\mathrm{m\,s}, mmax⁡=1m_{\max}=1, α=0.3\alpha=0.3 and ax=ay=0.235 ma_x=a_y=0.235\,\mathrm{m} from (5).

Because (7) sums one function of xx and one of the four corner heights of (8) are coplanar for every (mx,my)(m_x,m_y), as are those of the planar baseline: the two controllers command the same family of corner planes and differ only in the map from commanded slope to that plane. The planar map tilts the plane by mim_i wherever the target lies; the catenary map tilts it by −2asinh⁡(x0,i/a)sinh⁡(D/2a)/D-2a\sinh(x_{0,i}/a)\sinh(D/2a)/D with x0,ix_{0,i} from (3), which is nonzero at mi=0m_i=0 whenever the target is off centre, placing the vertex of the sag at the target, and whose sensitivity to mim_i grows with the distance of the vertex from the centre. At mi=0m_i=0 the planar map commands a level plane, under which an object at an off centre target rolls toward the sag minimum, whereas the catenary map commands the tilt that places the sag minimum at the target. The catenary controller is thus a position dependent feedforward tilt and gain schedule on the planar one, and no constant retuning of the planar gains reproduces it.

Catenary Against Planar Control in Simulation

To measure the success rate in simulation on a single module: the workspace is divided into 400 subsections of 0.025×0.0250.025\times0.025 m, each receives 10 trials with a random target inside it and a random initial object position, and a trial succeeds if the object reaches within ρ=0.03 m\rho= 0.03\,\mathrm{m} of the target inside tmax⁡=10 st_{\max} = 10\,\mathrm{s} without leaving the surface. Figure 4 gives the maps for the sphere. The planar controller attains a mean success rate of 42.8%, with success confined to a scattered band through the centre; the catenary controller attains 79.1%, and its success region is one contiguous area covering most of the module interior. Residual failures at the corners are objects leaving the module edge, which the simulated contact does not fully prevent. The gains are largest in the central and near edge regions, where the feedforward tilt of § 5-A holds an off centre target that the planar controller cannot.

Figure 4. Success rate maps for a sphere on a single module in simulation. (a) Planar controller [7]. (b) Catenary controller.

Design of Suspended Fabric Surfaces

Of the four surface models, only the catenary is both expressed in the quantities a designer selects, the module span DD, the fabric length SS and the actuator limit umax⁡u_{\max}, and invertible from a commanded slope to support heights (Section IV-D), which is the map a reachability analysis evaluates at every candidate target. This section derives from it the fraction of a module that the controller can hold as a function of those three quantities.

Reachability Condition

A target pt=(xt,yt)\mathbf{p}_{t} = (x_{t}, y_{t}) is defined as reachable if the controller can hold a zero corrective slope at pt\mathbf{p}_{t} without any actuator exceeding its limit, that is if the configuration mx=my=0m_{x} = m_{y} = 0 with αv=0\alpha_{v} = 0 in algorithm 1 satisfies ∣uj∣≤umax⁡|u_{j}| \le u_{\max} for all jj. The critical case arises when the target lies near a module corner, where the profile must produce a large height difference between the near and far actuators.

The condition is evaluated pointwise across a module. For each candidate target the margin is the minimum remaining actuator headroom,

μ(xt,yt)=umax⁡−max⁡j∣uj∣,(9)\mu(x_{t}, y_{t}) = u_{\max} - \max_{j} |u_{j}|, \tag*{(9)}

and the fraction of module area with μ>0\mu> 0 defines the reachable workspace percentage. The condition tightens to a required slope reserve mrm_{r} by evaluating (9) at ∣mx∣=∣my∣=mr|m_{x}| = |m_{y}| = m_{r}; the charts below use mr=0m_{r} = 0, the weakest form.

Design Charts

Figure 5 presents the resulting design space, with slack defined as (S−D)/D(S-D)/D. At the operating point of the platform, S=0.6 mS = 0.6\,\mathrm{m} and 20% slack, the reachable region covers the whole module; as the fabric lengthens it contracts from the corners inward, to 74% at S=0.7 mS = 0.7\,\mathrm{m} and 21% at S=0.99 mS = 0.99\,\mathrm{m}, where it is confined to a small diamond about the centre. In the lower left panel the Smin⁡S_{\min} curve of (6) separates sheets too short to connect actuators at opposite extremes of their range from sheets whose slack costs coverage; the lower right panel shows that larger spans require proportionally more material for the same coverage.

Design space of a suspended fabric module

Figure 5. Design space of a suspended fabric module. Top: margin maps μ(xt,yt)\mu(x_t,y_t) of (9) at five operating points A* to E of increasing fabric slack; green is positive margin, red is actuator saturation and the black contour is the zero margin boundary. Bottom: reachable workspace percentage over fabric length and actuator limit (left) and over fabric length and module span (right), with the blue curve giving Smin⁡S_{\min} from (6) and the star marking the operating point of the platform. Parameters not varied are held at D=0.5 mD=0.5\,\mathrm{m} and umax⁡=0.16 mu_{\max}=0.16\,\mathrm{m}.

The charts turn the selection of platform parameters into a reading of contours: given a span fixed by the application and a required coverage, the admissible band of fabric length lies between the Smin⁡S_{\min} curve and the contour of that coverage, and its width is the tolerance to fabric stretch and wear. For

the present platform that band is narrow: the operating point lies 6 mm above Smin⁡S_{\min}, and a 0.1 m increase in fabric length would remove the corners from the reachable set unless the actuator limit were raised accordingly.

Multimodular Extension

To extend the workspace beyond a single module, actuators are arranged on an (n+1)×(n+1)(n + 1) \times(n + 1) grid forming n×nn \times n modules that share boundary actuators with their neighbours. In the 2×22 \times2 configuration of Figure 1B, nine actuators define four modules M0 to M3 covering 1 m21\,\mathrm{m}^{2}. Adjacent modules share two boundary actuators and diagonal modules share one, so the actuator density falls from sixteen to nine, a reduction of 44% at this scale that approaches 75% asymptotically. Each actuator operates as an independent unit, which preserves robustness to individual faults.

Objects are transferred by raising the actuators that belong exclusively to the current module while lowering the remaining actuators, namely the two shared with the destination module and the two belonging to it. The resulting local slope induces rolling, sliding or a combination of the two. Transfer operates hierarchically: a planner based on Manhattan distance determines the module sequence and enforces conflict free paths, so that objects under simultaneous manipulation never occupy the same module, while a lower layer executes each transfer as a timed actuator sequence with feedback from the tracking system and adaptive retries at increased actuator height and hold duration. The lateral path of the transfer is selected through the choice of shared actuator to raise: raising the inner shared actuator produces a left path, raising the outer one produces a right path, and raising both equally produces a central path. Once the object rests on the destination module, the catenary controller of § 5 acts on that module alone.

Target Reaching on multi-modular Platform

Target reaching evaluates end to end manipulation with the five objects of Table II: transfer along a Manhattan path to the target module, then the catenary controller on that module, on the 2×22 \times2 membrane of § 2 and on the hardware platform. Table IV reports the final error per object for two runs. In simulation every object comes within 3 cm of the target in both trials and finishes 0.9 to 2.7 cm from it; on hardware the sphere, cube and disk do the same in 6 to 11 s including transfer, while the egg and cylinder reach 3 cm in one of two trials each, the cylinder with the largest final error. Rolling objects converge fastest on both references; the sliding cube and disk settle about twice as slowly in simulation, where the contact friction is lower than on the fabric.

ObjectSimulation SR3_3Simulation t3t_3 [s]Simulation ϵfin\epsilon_{\mathrm{fin}} [cm]Hardware SR3_3Hardware t3t_3 [s]Hardware ϵfin\epsilon_{\mathrm{fin}} [cm]
Sphere2/26.2±1.06.2 \pm1.00.9±0.00.9 \pm0.02/26.4±0.46.4 \pm0.41.6±0.71.6 \pm0.7
Cube2/216.7±1.216.7 \pm1.21.9±0.31.9 \pm0.32/28.5±2.88.5 \pm2.81.9±0.41.9 \pm0.4
Disk2/219.2±0.519.2 \pm0.52.7±0.22.7 \pm0.22/211.1±2.511.1 \pm2.52.3±0.12.3 \pm0.1
Egg2/28.1±0.18.1 \pm0.11.6±0.31.6 \pm0.31/25.35.32.1±2.52.1 \pm2.5
Cylinder2/213.5±0.913.5 \pm0.91.5±0.51.5 \pm0.51/29.99.93.7±3.23.7 \pm3.2

Table IV. End to end target reaching with the catenary controller on the 2×22 \times2 simulated membrane and hardware platform: two trials per object. SR3_3: trials that came within 3 cm of the target at any time; t3t_3: time from trial start, transfer included, to first reach 3 cm, over successful trials; ϵfin\epsilon_{\mathrm{fin}}: final distance to the target. Mean ±\pm sd. Every trial came within 5 cm except one hardware cylinder trial.

ScenarioObject\multicolumn{2}{c}{No comp.}\multicolumn{2}{c}{Comp.}Δ\Delta
Target, adjacentSpheredrmsd_{\mathrm{rms}}dmax⁡d_{\max}drmsd_{\mathrm{rms}}dmax⁡d_{\max}78%
Target, adjacentDisk0.0640.0760.0260.04059%
Target, diagonalSphere0.0310.058NANANA
Target, diagonalDisk0.0350.044NANANA
Transfer, perp.Sphere0.0440.0650.0310.04430%
Transfer, perp.Disk0.0570.1480.0220.03661%
Transfer, opp.Spherelostlost0.0150.030NA
Transfer, opp.Disklostlost0.0090.018NA

Table V. Displacement of a stationary object on a passive module while an object is manipulated on a neighbouring module, in metres, mean of three repetitions. drmsd_{\mathrm{rms}}, dmax⁡d_{\max}: root mean square and maximum displacement over the manipulation; Δ\Delta: reduction of drmsd_{\mathrm{rms}} with compensation; lost: object left the module; NA: not tested.

Interference From Shared Boundary Actuation

A shared actuator serves two modules, so manipulating an object on one module deforms the surface of its neighbours. The perturbation is quantified by tracking a stationary object on a passive module while another object is manipulated on a neighbouring one, and is reported through the root mean square displacement over the manipulation duration and the maximum displacement. A sphere and a disk serve as stationary objects, representing rolling dominant and sliding dominant geometries. Four spatial configurations are evaluated: target reaching on a module that shares two actuators with the passive module (adjacent) or one (diagonal), and transfer that activates one shared actuator (perpendicular) or both (opposite).

tbl:V summarises the results. Without compensation, the adjacent configuration produces severe displacement of the sphere, with a root mean square value of 0.217 m and a maximum displacement of 0.460 m, comparable with the module span, indicating exit from the module. The disk shows lower but substantial sensitivity, its flat contact geometry resisting rolling. The diagonal configuration couples markedly less, consistent with interference scaling with the number of shared actuators. During transfer with both shared actuators raised, the stationary object is displaced beyond the module boundary and is lost.

The simple first-step compensation raises the two actuators of the passive module that are not shared with the active module. When the shared actuators move during manipulation on the active module, the passive surface develops an unintended tilt toward it; raising the non shared actuators creates a counter tilt that restores a locally level surface. Compensation reduces the root mean square displacement by 30 to 78% across configurations, brings the adjacent configuration to a level comparable with the uncompensated diagonal configuration, and prevents object loss during transfer with both shared actuators active.

Discussion

Model. Fabric elasticity and wear are not represented, the sag parameter is set offline, and the unloaded assumption restricts the model to light objects (Section IV-C). The hardware ordering of the surface models rests on three captures and is resolved on the matched command but only partially in the held out aggregate, and the equilibrium comparison is simulation only. The controller comparison of § 5-B is performed on the tensioned simulated membrane, so its success rates characterise the two controllers relative to each other rather than predicting hardware coverage, and the gains were tuned through the catenary map, so part of the margin may reflect tuning.

Design. The reachability condition is geometric. It does not account for the friction and object mass that motion must overcome, so a target reachable in the charts may be unreachable for a heavy or high friction object, nor for pulling, in which fabric tension displaces the object without a net slope. The charts use the geometric sag parameter a=0.235 ma = 0.235\,\mathrm{m}, whereas the command driven calibration of Section IV-A returns 0.335 m0.335\,\mathrm{m} in simulation and 0.440 m0.440\,\mathrm{m} on hardware; a larger aa flattens the profile and widens the reachable set, so the charts are conservative with respect to the calibrated values, and they have been checked against the platform at one operating point.

Multimodular platform. Transfer between modules relies on an open loop actuator sequence whose outcome is checked only after the hold, so a failed transfer costs a full retry; the planner admits at most one actively manipulated object per module, and shared boundary actuation is not compared against independent actuation of the same grid. The platform is demonstrated at the 2×22 \times2 scale on hardware only; in a 3×33 \times3 grid the central module shares actuators with four neighbours, so the growth of interference sources is expected to require decentralised compensation. Object position is tracked by an external motion capture system, which bounds deployability and is a single point of failure.

Future work includes extending the model with a load term that depends on the mass and position of one or several objects, which would cover heavier payloads, estimating the sag parameter online to follow fabric wear, and adding friction and object mass to the reachability condition to tighten the charts. Tracking the object during the hardware captures would allow the equilibrium test of Section IV-B to be repeated on the physical fabric, and repeating the success rate maps of § 5-B on hardware would confirm the controller comparison with real contact and friction.

Conclusion

This paper presented a separable catenary model of a suspended fabric manipulation surface, a design space derived from it, and a multimodular platform that extends the module to larger areas. On a matched command the catenary ranks second of four surface descriptions by height error on both a simulated membrane and the physical fabric, behind a membrane energy model that cannot be evaluated at the control rate, and it predicts the rest position of five object geometries better than any of them; a controller built on it nearly doubles the mean target reaching success rate of the planar baseline in simulation. Because the model is expressed in module span, fabric length and actuator stroke, it yields a minimum fabric length bound and charts of reachable workspace from which platform parameters can be read directly. Shared boundary actuation requires (n+1)2(n + 1)^2 actuators for an n×nn \times n grid; on a 2×22 \times2 prototype heterogeneous objects transferred between modules reach targets within 0.03 m0.03\,\mathrm{m}, and the interference the shared actuators introduce is reduced by 30 to 78% through actuator compensation.

References

  1. [1]Deepak Parajuli, Mark D Bedillion, and Randy C Hoover. Actuator array manipulation using low resolution local sensing. In ASME International Mechanical Engineering Congress and Exposition, volume 46476, page V04AT04A003. American Society of Mechanical Engineers, 2014.DOI
  2. [2]Zhengrong Xue, Han Zhang, Jingwen Cheng, Zhengmao He, Yuanchen Ju, Changyi Lin, Gu Zhang, and Huazhe Xu. Anyrobot: Reinforcement learning for generalizable distributed manipulation through touch. In 2024 IEEE International Conference on Robotics and Automation (ICRA), pages 16744–16751. IEEE, 2024.arxiv.org/abs/2306.16857
  3. [3]Sarvesh Patil, Tony Tao, Tess Hellebrekers, Oliver Kroemer, and F. Zeynep Temel. Linear delta arrays for compliant dexterous distributed manipulation. In 2023 IEEE International Conference on Robotics and Automation (ICRA), page 10324–10330. IEEE, May 2023.DOI
  4. [4]Festo AG. Wavehandling: modular conveyor with intelligent subsystems. https://www.festo.com/gb/en/e/about-festo/research-and-development/bionic-learning-network/highlights-from-2013-to-2014/wavehandling-id_33578/, 2013.
  5. [5]Chih-Han Yu, Kristina Haller, Donald Ingber, and Radhika Nagpal. Morpho: A self-deformable modular robot inspired by cellular structure. In 2008 IEEE/RSJ International Conference on Intelligent Robots and Systems, pages 3571–3578. IEEE, 2008.DOI
  6. [6]Pratik Ingle, Kasper Støy, and Andres Faiña. Soft manipulation surface with reduced actuator density for heterogeneous object manipulation. In 2025 IEEE 8th International Conference on Soft Robotics (RoboSoft), pages 1–8, 2025.arxiv.org/abs/2411.14290
  7. [7]Pratik Ingle, Kasper Støy, and Andres Faiña. Heterogeneous object manipulation on nonlinear soft surface through linear controller. In 2025 IEEE 21st International Conference on Automation Science and Engineering (CASE), pages 1780–1787, 2025.arxiv.org/abs/2507.14967
  8. [8]Binayak Roy, Arin Dasmajian, and H. Harry Asada. Repositioning of a rigid body with a flexible sheet and its application to automated rehabilitation bed. IEEE Transactions on Automation Science and Engineering, 2(3):300–307, 2005.DOI
  9. [9]Kyle Hunte and Jingang Yi. Collaborative manipulation of spherical-shape objects with a deformable sheet held by a mobile robotic team. IFAC-PapersOnLine, 54(20):437–442, 2021.DOI
  10. [10]Jiawei Hu, Wenhang Liu, Heng Zhang, Jingang Yi, and Zhenhua Xiong. Multi-robot object transport motion planning with a deformable sheet. IEEE Robotics and Automation Letters, 7(4):9350–9357, 2022.arxiv.org/abs/2111.09046
  11. [11]Wenyao Ma, Jiawei Hu, Jiamao Li, Jingang Yi, and Zhenhua Xiong. Stable kinematics for multirobot collaborative transporting system with a deformable sheet. IEEE Transactions on Robotics, 42:837–853, 2026.DOI
  12. [12]Jerry Weil. The synthesis of cloth objects. In Proceedings of the 13th Annual Conference on Computer Graphics and Interactive Techniques (SIGGRAPH ’86), pages 49–54, 1986.
  13. [13]Daobo Zhang and Josef Kiendl. A variationally consistent membrane wrinkling model based on spectral decomposition of the strain tensor. Computer Methods in Applied Mechanics and Engineering, 432:117386, 2024.DOI
  14. [14]Emanuel Todorov, Tom Erez, and Yuval Tassa. MuJoCo: A physics engine for model-based control. In 2012 IEEE/RSJ International Conference on Intelligent Robots and Systems, pages 5026–5033. IEEE, 2012.DOI

Paper details

vlnc:W_y2rk3njq
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 1

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Computer Science

Not recorded for this paper

View statement
Looking for related papers…
Contents