betaFeedback

WorksPhysics and Astronomy

Thermo-optic tuning of directional infrared emissivity

Abstract

Tuning the spatial extent of directional thermal emission across an arbitrary, and fixed spectral bandwidth is a fundamentally enabling capability for a range of emerging applications such as thermophotovoltaics, thermal imaging, and radiative cooling. However, previous experimental demonstrations were limited to narrow bandwidths, and the resonance frequency itself changed significantly as a function of the reconfigured directional response. Here, we demonstrate thermo-optic tuning of directional infrared emissivity using InAs-based gradient ENZ materials functioning as broadband directional thermal emitters whose angular selectivity can be modified via thermal free-carrier effects. We experimentally demonstrate two emitters achieving a 5° and 10° increase in the angular extent of their directional emissivity in the p-polarization across a prescribed, broad wavelength range of operation (12.5 to 15μμm), for moderate temperatures below 400 K. Temperature-driven control of directional emissivity offers a new mode of post-fabrication control of radiative heat transfer that may in turn enable novel device functionalities.

Introduction

Thermal emission is generally assumed to be incoherent in both space and time, with its light emission toward the far-field being broadband and omnidirectional[1]. Deliberately constraining thermally generated light emission to specific angular channels across a broadband frequency range is a fundamentally enabling capability[2], which has stimulated an active field of research both theoretically[2, 3] and experimentally[4, 5, 6, 7]. In this context, nanophotonic structures with post-fabrication tunability have garnered significant attention and have been increasingly explored more recently. Reconfigurability of the spatial or temporal content of broadband far-field thermal radiation offers transformative potential across a broad range of applications such as thermal imaging[8, 9, 10], sensing[11, 12, 13], and energy conversion[14, 15, 16].

While significant progress has been made in tuning spectral properties using external stimuli[17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27] (e.g. electrical gating, optical pumping or temperature), dynamically controlling the angular response of thermal emission has proven to be more challenging[28]. Electrostatic modulation of the directionality of thermal emission has been experimentally explored in gap plasmon polariton based micro strip cavity modes[29, 30, 31] and Fabry-Perot resonance cavities supporting long-range delocalized modes[32]. However, the spectral bandwidth of directional emissivity was narrowband in nature and the resonance frequency itself changed significantly as a function of the peak emissivity angle of incidence. Alternatively, doped III-V semiconductor-based gradient epsilon-near-zero (ENZ) materials can be designed to behave as broadband directional thermal emitters[5]. Since semiconductor-based gradient ENZ photonic structures are driven by free carrier (electron or hole) concentrations, this approach holds great potential for enabling on-demand spatio-temporal control of emissivity through free-carrier effects. Recent work, for instance, has experimentally demonstrated that doped semiconductor-based gradient ENZ photonic structures can be used to realize broadband nonreciprocal thermal emitters by externally applying a static magnetic field in the Voigt geometry[33, 34].

Thermal emission, however, is intrinsically a temperature dependent phenomenon[1]. Controlling thermal emission through temperature effects has been studied in the past, and semiconductors have been investigated in this context due to their temperature dependent free-carrier effects[35, 36, 37]. Modal refractive index shifts in semiconductor Mie resonators have been shown based on traditional thermo-optic effects[38, 39, 40]. Spectrally tunable thermal antennas were also demonstrated by thermally tuning the plasma frequency of III-V semiconductors[41]. However, prior work has not demonstrated the ability to tune the angular extent of a broadband directional emitter, and the spectral extent of the emitter was limited to narrow operational bandwidths centered at the tunable excitation frequency of the fundamental optical mode, with no distinct directionality.

Here, we explore the thermo-optic tuning of a broadband directional thermal emitter whose angular extent of “thermal beaming”, and thus its angular selectivity, can be controlled via thermal free-carrier effects. We experimentally demonstrate this capability via semiconductor gradient ENZ photonic structures based on epitaxially grown graded doped InAs. We show this effect for photonic structures manifesting, by design, highly directional thermal emission, peaking at 75∘75^\circ and 65∘65^\circ respectively, across a broad bandwidth between 12.512.5 to 15 μm15\,\mu\mathrm{m}. We show that the angular width of average emissivity >0.4> 0.4 over 2 μm2\,\mu\mathrm{m} bandwidths can be gradually modulated by 5∘5^\circ and 10∘10^\circ for the respective structures within moderate temperature ranges (<400< 400 K), hence, achieving reconfigurable angular selectivity across a broad emissivity bandwidth. We describe the temperature-dependent optical response using theoretical and empirical models, showing that the angular range of high emissivity can be further reduced by 8∘8^\circ and 15∘15^\circ at lower temperatures (200 K) compared to the spectra at 375 K for two fabricated structures enabling tailored control over the directional range of high emissivity and angular selectivity, while maintaing the spectral response over a prescribed emissivity bandwidth by design.

Results and Discussion

To explore thermal control of directional emissivity, we use thin, subwavelength films of materials whose permittivity approaches and crosses zero, i.e. epsilon-near-zero (ENZ) behavior[42], as our model system. Planar ENZ films are known to support a leaky electromagnetic mode near the material resonance pole in the p polarization, often called the Berreman mode[43, 44, 45, 46, 47]. This mode can couple to propagating free-space modes over a range of wave vectors and thus exhibits a directional response in its emissivity which can be controlled by adjusting the film thickness[43]. We begin by considering an ideal gradient ENZ framework consisting of finite number of thin films, each defined by a Drude-Lorentz permittivity function with the same loss factor (γ\gamma) but complementary resonance frequencies that vary gradually along the depth dimension. Through transfer matrix simulations we observe that the ideal gradient ENZ film exhibits broad-spectrum directional thermal emission where the angular extent of high emissivity (here, arbitrarily defined as ε>0.8\varepsilon> 0.8) is Δθ=30∘\Delta\theta= 30^\circ and the angular selectivity (here, defined as s=1−Δθ/90∘s = 1 - \Delta\theta/90^\circ) is s=0.67s = 0.67, across a wide dimensionless operational range Δω=0.2\Delta\omega= 0.2 from 1.5 to 1.7, described by the complementary resonance frequencies of the constituent thin films (Fig. S1b). In theory, by increasing the loss factor (γ×2\gamma\times2) of the constituent thin films, the angular extent of high emissivity can be broadened (θγ×2=5∘\theta_{\gamma\times2} = 5^\circ), and the angular selectivity can be reduced (s=0.61s = 0.61) (Fig. S1c). Alternatively, by reducing the loss factor (γ/2\gamma/2) of the constituent thin films, one can narrow (θγ/2=5∘\theta_{\gamma/2} = 5^\circ) the angular extent of high emissivity, and the directional response of the thermal emitter can become sharper (s=0.72s = 0.72), consistently across the entire bandwidth (Fig. S1a). This capability is in marked contrast to previously reported reconfigurable platforms employing cavity modes[29, 30, 31, 32], where the spectral bandwidth of the directional emission was typically narrow bandwidth and the resonance frequency itself changed significantly as a function of the reconfigured directionality of high emissivity.

We showcase this capability using InAs-based gradient ENZ photonic structures. The first structure we designed and grew by molecular beam epitaxy was composed of InAs thin films of the same thickness with the doping concentration ranging from 2.0×1018 cm−32.0\times10^{18}\ \mathrm{cm}^{-3} to 4.5×1018 cm−34.5\times10^{18}\ \mathrm{cm}^{-3} (Figure 1b). In the first structure, the thickness of the individual layers was 50 nm each and they were epitaxially grown atop a heavily doped InAs layer with a doping concentration of 5.0×1019 cm−35.0\times10^{19}\ \mathrm{cm}^{-3} and thickness of 300 nm. The gradient ENZ structure was grown on a 50 mm (2 inch) semi-insulating GaAs substrate, with a total InAs film thickness of 600 nm (Figure 1a). We observe “thermal beaming” throughout a broad wavelength range from 12.5 to 15 μ\mum, where the angular extent of p-polarized average emissivity above 0.4 throughout the entire bandwidth is Δθ=20∘\Delta\theta= 20^\circ centered at 75° (Figure 1c and Fig. S2a).

Configuration of an InAs-based gradient ENZ thin film manifesting broadband directional thermal beaming

Figure 1. Configuration of an InAs-based gradient ENZ thin film manifesting broadband directional thermal beaming. Schematic of the InAs-based gradient ENZ structure with a doping concentration range from 2.0×1018 cm−32.0\times10^{18}\ \mathrm{cm}^{-3} to 4.5×1018 cm−34.5\times10^{18}\ \mathrm{cm}^{-3} and individual layer thickness of 50 nm (a). The SEM image of the experimentally fabricated multilayer InAs film structure, with labels identifying the materials used and the total thickness of the gradient ENZ layer (b). c, Directional response over a broad wavelength range of operation (from 12.5 to 15 μ\mum) for structure 1 (300 nm) and 2 (900 nm), with peak average emissivity observed at 75° and 65°, respectively.

We first describe the temperature-dependent optical response of doped InAs, using the Drude formalism incorporating established theoretical and empirical models for the temperature-dependent bandgap, band curvature, and Fermi distribution:

ε=ε′+iε′′=ε∞(1−ωp2[T]ω2+iωΓ[T]),ωp2[T]=n[T]e2ε∞ε0m∗[T](1)\varepsilon= \varepsilon' + i\varepsilon'' = \varepsilon_\infty\left(1 - \frac{\omega_p^{2}[T]}{\omega^{2} + i\omega\Gamma[T]}\right), \qquad\omega_p^{2}[T] = \frac{n[T]e^{2}}{\varepsilon_\infty\varepsilon_0m^{*}[T]} \tag*{(1)}

We study the temperature-dependence of the Drude parameters for a doped InAs thin film with a room temperature free-carrier concentration n=2.5×1018n = 2.5 \times10^{18} cm−3^{-3}, effective mass m∗=0.038m0m^{*} = 0.038m_0 and scattering rate Γ=5.6\Gamma= 5.6 THz[48]. The free-carrier concentration was chosen such that it corresponds to a value within the doping concentration range of the InAs-based gradient ENZ photonic structure. The effective mass of the free-carriers was calculated using the Kane model[49, 50], accounting for the non-parabolicity of the conduction band-edge of InAs (see Figure 2a and Supplementary Section 4). Here, the temperature-dependent band gap was modeled using the empirical Varshni model[51, 52] for InAs (see Supplementary Section 4) and the free-carrier concentration was empirically determined by temperature-dependent Hall measurements using our reference InAs film epitaxially grown on a semi-insulting substrate (Figure 2a). The temperature-dependent plasma frequency ωp[T]\omega_p[T] was calculated using Eq. (1) (Figure 2b), incorporating the non-parabolic effective mass m∗[T]m^{*}[T] and the free-carrier density n[T]n[T] from Figure 2a. The plasma frequency remains relatively constant with increasing temperature, which can be explained by the increase of the electron effective mass balanced with the minimal increase in carrier density for a doped InAs thin film. The temperature-dependent scattering rate Γ[T]\Gamma[T] was also obtained by curve-fitting experimentally reported values inferred from the literature (Table S1, Supporting Information). Although low frequency conductivity measurements are not necessarily a good indicator of optical conductivity[37], the temperature-dependent Hall mobility measurements clearly show a decreasing trend (Figure 2b), indicating the enhancement of scattering processes with increasing temperature[53, 54].

Temperature-dependent Drude parameters of doped InAs

Figure 2. Temperature-dependent Drude parameters of doped InAs. Effective mass of the free-carriers calculated using the Kane model and experimentally measured Hall carrier concentration of a doped InAs thin film (n=2.5×1018n = 2.5 \times10^{18} cm−3^{-3}) at different temperatures (a). The plasma frequency was calculated using Eq. (1) (b), incorporating the values from (a). The measured Hall mobility shows a decreasing trend indicating the enhancement of scattering processes with increasing temperature (b). The real and imaginary parts of the permittivity at different temperatures (c), calculated based on the temperature dependent Drude parameters studied in (a) and (b). The invariance of the real part of the permittivity combined with the gradual tunability of the imaginary part of the permittivity makes gradient ENZ photonic structures based on doped InAs thin films ideal for a thermally reconfigurable metamaterials platform.

Based on the temperature dependent Drude parameters studied, we numerically calculate the real and imaginary parts of the permittivity of a doped InAs thin film (n=2.5×1018 cm−3n = 2.5 \times10^{18}\ \mathrm{cm}^{-3}) for different temperatures using Eq. (1). With increasing temperature from 200 K to 375 K, the real part of the permittivity, hence, the ENZ wavelength (∼14.5 μm\sim14.5\ \mu\mathrm{m}) slightly red-shifts, however, stays relatively constant throughout this temperature range (Figure 2c). The imaginary part of the permittivity at the ENZ wavelength (∼14.5 μm\sim14.5\ \mu\mathrm{m}) shows a gradual increase from 0.5 to 1.7 with increasing temperature from 200 K to 375 K. The key feature these measurements reveal, the thermal invariance of the real part of the permittivity combined with the gradual change in the imaginary part of the permittivity with temperature, makes this a unique platform. It enables us to thermally reconfigure the angular extent of high emissivity for a fixed spectral emissivity bandwidth.

To experimentally verify the tunability of the angular extent of thermal beaming, we measure the emissivity spectra of the fabricated structure (structure 1) as a function of angle and wavelength in the p-polarization (Figure 3a-Figure 3c), using a FTIR spectrometer as the structure’s temperature is modulated by a small form factor thermoelectric Peltier module. Since the gradient ENZ layer was grown on an optically thick metal layer, the transmissivity (TT) is equal to 0 and the emissivity (ϵ\epsilon) is determined through the measured reflectivity (RR) as a function of polar angle of incidence (ϵ=1−R\epsilon= 1 - R). The emissivity spectra exhibit strong directional emission, where a gradual increase in the angular extent of directional emissivity is observed with increasing temperature from 285 K to 335 K and 375 K. The spectral extent on the other hand, remains fixed across a broad wavelength range from 12.5 to 15 μ\mum associated with the ENZ wavelength range of the constituent doped InAs thin films of the gradient ENZ layer[48].

Experimental tuning of infrared emissivity for two broadband directional thermal emitters

Figure 3. Experimental tuning of infrared emissivity for two broadband directional thermal emitters. a-c Measured emissivity spectra in the p polarization for structure 1 (300 nm) at (a) 285 K, (b) 335 K and (c) 375 K. Tthe structure’s temperature is modulated by a small form factor thermoelectric Peltier module.. Measured emissivity spectra for structure 2 (900 nm) at (d) 285 K, (e) 335 K and (f) 375 K.

To better characterize the thermal free-carrier effect on directional emissivity, we plot the overall p-polarized emissivity for the first structure over its wavelength range of operation (12.5 to 15 μ\mum) in polar coordinates (Figure 4a). As compared to the emissivity spectra at room temperature, we observe a narrowing of the angular width of high emissivity (ϵ>0.4\epsilon> 0.4) at 285 K, and a gradual increase of the angular width by 5°, corresponding to a gradual decrease in angular selectivity from 0.79 to 0.73, as the temperature increases from 285 K to 335 K and 375 K. Hence, we clearly see that one can gradually narrow or broaden the angular extent of the broadband beaming effect by controlling the temperature of the gradient ENZ photonic structure for an arbitrary, and fixed wavelength range of operation. To validate our experimental results, we simulated the average emissivity in the p-polarization of structure 1 over the wavelength range of operation (12.5 to 15 μm\mu\mathrm{m}) in polar coordinates (Figure 4b), using the transfer matrix method incorporating the temperature-dependent Drude formulism developed in Eq. (1). Although the measured emissivity is lower than what was predicted from the simulated data, the angles of operation as well as the gradual trend of the thermal reconfigurability with respect to temperature is in good agreement with the simulation. We note that the constraints in the absorptivity measurement setup did not allow for measurements at temperatures below 10∘C10^\circ\mathrm{C}. However, further simulations at lower temperatures (200 K) suggest that the angular extent of high emissivity could be further reduced by as much as 8∘8^\circ compared to the spectra at 375 K, exhibiting strong directional emission reaching an angular selectivity of 0.81, while maintaining its broad wavelength range of operation (Fig. S2a). This highlights the remarkable tunability of the directional response of broad-spectrum directional thermal emission of InAs-based gradient ENZ photonic structures by thermal free-carrier effects.

Comparing experimental measurements with simulation results

Figure 4. Comparing experimental measurements with simulation results. a,c Measured average p-polarized emissivity over a broad wavelength range of operation (from 12.5 to 15 μ\mum) at different temperatures for structure 1 (a) and structure 2 (c). b,d Simulated average emissivity over the same operational range for structure1 (b) and structure2 (d). The simulation results show gradual tuning of the angular extent of directional thermal emission and match well with the experimental results.

We fabricated a second semiconductor gradient ENZ structure (structure 2) with a doping concentration range of the gradient ENZ thin film ranging from 2.0×1018 cm−32.0 \times10^{18}\ \mathrm{cm}^{-3} to 4.5×1018 cm−34.5 \times10^{18}\ \mathrm{cm}^{-3}, identical to structure 1, however, with a larger individual layer thickness of 150 nm, so that the total thickness of the gradient ENZ thin film was 900 nm; from which we expected to observe thermal tuning of the directional response at smaller angular ranges for the same temperature range (<400< 400 K). At room temperature, we observe strong directional emissivity throughout the same wavelength range from 12.5 to 15 μm\mu\mathrm{m}, as in structure 1. However, the angular extent of the p-polarized average emissivity above 0.4 across the entire bandwidth was Δθ=30∘\Delta\theta= 30^\circ, centered at a smaller angular range around 65∘65^\circ (Figure 2c and Fig. S1b). This difference in the angular response of structure 2 originates fundamentally from the spatial shift of the optical mode supported by thicker Berreman films relative to the thinner ones in structure 1 (Fig. S3). The thermally reconfigured emissivity spectra exhibits, similar to structure 1, strong directional emission throughout a constant operational wavelength range from 12.5 to 15 μm\mu\mathrm{m}, where a gradual increase in the angular extent of directional emissivity is observed with increasing temperature from 285 K to 335 K and 375 K (Figure 3d-Figure 3f). We emphasize that the broad spectral range of this directional modulation scheme can be arbitrarily prescribed by changing the doping concentration range of the gradient ENZ layer (Fig. S4). Upon a closer examination of the p-polarized average emissivity in polar coordinates, we observe a narrowing of the angular width of high emissivity (ϵ>0.4\epsilon> 0.4) at 285 K, however, as compared to structure 1, a larger overall modulation of the angular extent of high emissivity of 10°, corresponding to a gradual decrease in angular selectivity from 0.57 to 0.46, as the temperature increases from 285 K to 335 K and 375 K (Figure 4c). As with structure 1, we compare the experimental results with simulations using the transfer matrix method and see excellent agreement, with both simulations and experiments exhibiting a larger 10° modulation of the angular width of high emissivity across the same temperature range (<400< 400 K), as compared to structure 1 (Figure 4c,Figure 4d). Additional simulations at lower temperatures (200 K) also suggest that the angular range of high emissivity could be further reduced as with structure 1, but as much as 15° compared to the spectra at 375 K, reaching an angular selectivity of 0.76 (Fig. S2b). A similar volumetric effect of thicker InAs layers exhibiting larger modulation relative to thinner ones has been reported in previous magneto-optic studies[33].

To elucidate the physical origin of the temperature-dependent beaming effect, we numerically calculate the temperature-dependent dispersion relation of these leaky Berreman modes[43, 44] (Fig. S5 and Figure 5a). In Figure 5a, we show the imaginary frequency in the dispersion relation of a doped InAs Berreman film at different temperatures. Here, we see that the imaginary frequency increases with increasing temperature from 285 K to 335 K and 375 K. From a fundamental optical mode point of view, the imaginary frequency corresponds to the degree of attenuation of the electromagnetic wave as it oscillates within the medium. This degree of attenuation can place limits on the directional contrast of emissivity. If the attenuation is larger for the constituent ENZ films at wavelengths near the ENZ wavelength, high emissivity will occur over a wide range of wave vectors, thus broadening the angular extent of thermal beaming. The real part of the frequency in the dispersion relation, on the other hand, remains constant with temperature modulation, indicating the invariance of the oscillation frequencies of these localized modes within these temperature ranges (Fig. S5). From a materials point of view, this thermal free-carrier effect could be understood as the material becoming more lossy and thus absorbing the incident optical power rather than allowing it to oscillate or propagate freely. To validate this, we calculated the electric field intensity distribution for the peak emissivity angle illumination at the center wavelength (λ≈13.5 μm\lambda\approx13.5\ \mu\mathrm{m}) of the operational wavelength range for both structure 1 and 2 (Figure 5b,Figure 5c). At room temperature, we observe a pronounced electric field enhancement at the center of the gradient ENZ layer, corresponding to the constituent layers supporting the Berreman mode at the central wavelengths within the high emissivity spectral bandwidth. Notably, the heavily doped InAs layer exhibits negligible electric field intensity in the simulations, remaining highly reflective over the wavelength range of operation and effectively pushing the field into the gradient ENZ layer. With decreasing temperature, however, we observe an enhancement in the intensity of the localized field. Conversely, with increasing temperature, we observe a reduction in the intensity of the localized field across the gradient ENZ layer, as the resonant optical modes are progressively converted into lattice vibrational modes. We also note that the overall spatial distribution of the electric field enhancement remains constant at the center of the gradient ENZ layer, indicating the invariance of the optical resonance frequency leading to the fixed broad-spectrum operational range of thermal beaming, regardless of the temperature.

Numerically calculated dispersion relation and electric field intensity distribution at different temperatures

Figure 5. Numerically calculated dispersion relation and electric field intensity distribution at different temperatures. a, The calculated imaginary frequency in the dispersion relation of doped InAs Berreman films at different temperatures. The narrowing and broadening of the angular extent of thermal beaming is due to the modulation of the degree of attenuation of the electromagnetic wave as it oscillates in the medium. b,c The calculated electric field intensity distribution for the peak emissivity angle illumination at the center wavelength (λ≈13.5\lambda\approx13.5 μ\mum) of the operational wavelength range for both structure 1 (b) and structure 2 (c). With increasing temperature, we observe a reduction in the intensity of the localized field across the gradient ENZ layer, as the resonant optical modes are progressively converted into lattice vibrational modes.

Conclusion

We have proposed and experimentally demonstrated a tunable and reconfigurable photonic platform for directional emissivity using InAs-based gradient ENZ materials, where the angular extent of thermal beaming can be tuned via thermal free-carrier effects across a broad spectral emissivity bandwidth. We show a 5° increase in the angular extent of directional emissivity with temperature increases below 400 K, over a broad operational wavelength range from 12.5 to 15 μm\mu\mathrm{m}, for the first structure we fabricated. For the second structure, we observe thermal reconfiguration of the directional response at smaller angular ranges within the same temperature range, but with a larger overall increase of the angular extent of high emissivity, reaching 10∘10^\circ. Our results show that the angular range of high emissivity can be further reduced by 8∘8^\circ and 15∘15^\circ at lower temperatures (200 K) compared to the spectra at 375 K for structures 1 and 2, respectively, where the directional response of the thermal emitter becomes sharper and more angularly selective across a prescribed bandwidth by thermal free-carrier effects. The reconfigurability of strong directional thermal emission to particular angular ranges over arbitrary broad spectral ranges, may yield substantial gains in device efficiency for existing technologies[55]. In particular, we believe that the III-V semiconductor-based nature of our thermally reconfigurable emissivity platform suggests its potential to inspire novel integrated photonic device concepts in the infrared, where the tunability of angular selectivity in broad-spectrum directional thermal emission can be leveraged.

Acknowledgements

This material was based upon work supported by the National Science Foundation under grant no. ECCS-2146577

References

  1. [1]Baranov, D. G. et al. Nanophotonic engineering of far-field thermal emitters. Nature materials 18, 920-930 (2019).DOI
  2. [2]Barbillon, G., Sakat, E., Hugonin, J.-P., Biehs, S.-A. & Ben-Abdallah, P. True thermal antenna with hyperbolic metamaterials. Optics Express 25, 23356-23363 (2017).DOI
  3. [3]Argyropoulos, C., Le, K. Q., Mattiucci, N., D’Aguanno, G. & Alu, A. Broadband absorbers and selective emitters based on plasmonic Brewster metasurfaces. Physical Review B 87, 205112 (2013).DOI
  4. [4]Xu, J., Mandal, J. & Raman, A. P. Broadband directional control of thermal emission. Science 372, 393-397 (2021).
  5. [5]Hwang, J. S., Xu, J. & Raman, A. P. Simultaneous Control of Spectral And Directional Emissivity with Gradient Epsilon-Near-Zero InAs Photonic Structures. Advanced Materials 35, 2302956 (2023).arxiv.org/abs/2212.14112
  6. [6]Cho, J.-W. et al. Directional Radiative Cooling via Exceptional Epsilon-Based Microcavities. ACS nano (2023).DOI
  7. [7]Fan, Z., Hwang, T., Lin, S., Chen, Y. & Wong, Z. J. Directional thermal emission and display using pixelated non-imaging micro-optics. Nature Communications 15, 4544 (2024).
  8. [8]Vollmer, M. in Computer Vision: A Reference Guide 666-670 (Springer, 2021).
  9. [9]Hulley, G. C. et al. High spatial resolution imaging of methane and other trace gases with the airborne Hyperspectral Thermal Emission Spectrometer (HyTES). Atmospheric Measurement Techniques 9, 2393-2408 (2016).DOI
  10. [10]Lucchi, E. Applications of the infrared thermography in the energy audit of buildings: A review. Renewable and Sustainable Energy Reviews 82, 3077-3090 (2018).DOI
  11. [11]Pan, Z. et al. Sensing properties of a novel temperature sensor based on field assisted thermal emission. Sensors 17, 473 (2017).
  12. [12]Gong, Y., Oh, S. S., Huffaker, D. L. & Copner, N. in Frontiers in Optics. JTu3A. 89 (Optical Society of America).
  13. [13]Palchetti, L., Di Natale, G. & Bianchini, G. Remote sensing of cirrus cloud microphysical properties using spectral measurements over the full range of their thermal emission. Journal of Geophysical Research: Atmospheres 121, 10,804-810,819 (2016).DOI
  14. [14]Mason, J., Smith, S. & Wasserman, D. Strong absorption and selective thermal emission from a midinfrared metamaterial. Applied Physics Letters 98, 241105 (2011).DOI
  15. [15]Jung, D., Bank, S., Lee, M. L. & Wasserman, D. Next-generation mid-infrared sources. Journal of Optics 19, 123001 (2017).DOI
  16. [16]Sakr, E. & Bermel, P. Thermophotovoltaics with spectral and angular selective doped-oxide thermal emitters. Optics Express 25, A880-A895 (2017).DOI
  17. [17]Park, J. et al. Dynamic thermal emission control with InAs-based plasmonic metasurfaces. Science advances 4, eaat3163 (2018).DOI
  18. [18]Iyer, P. P., Pendharkar, M., Palmstrøm, C. J. & Schuller, J. A. III–V heterojunction platform for electrically reconfigurable dielectric metasurfaces. ACS Photonics 6, 1345-1350 (2019).DOI
  19. [19]Lewi, T., Iyer, P. P., Butakov, N. A., Mikhailovsky, A. A. & Schuller, J. A. Widely tunable infrared antennas using free carrier refraction. Nano letters 15, 8188-8193 (2015).DOI
  20. [20]Dunkelberger, A. D. et al. Ultrafast active tuning of the Berreman mode. ACS Photonics 7, 279-287 (2019).DOI
  21. [21]Kim, S. et al. Electronically tunable perfect absorption in graphene. Nano letters 18, 971-979 (2018).DOI
  22. [22]Brar, V. W. et al. Electronic modulation of infrared radiation in graphene plasmonic resonators. Nature communications 6, 7032 (2015).DOI
  23. [23]King, J. et al. Electrically tunable VO2–metal metasurface for mid-infrared switching, limiting and nonlinear isolation. Nature Photonics 18, 74-80 (2024).arxiv.org/abs/2303.09060
  24. [24]Yao, Y. et al. Electrically tunable metasurface perfect absorbers for ultrathin mid-infrared optical modulators. Nano letters 14, 6526-6532 (2014).DOI
  25. [25]Inoue, T., De Zoysa, M., Asano, T. & Noda, S. Realization of dynamic thermal emission control. Nature materials 13, 928-931 (2014).DOI
  26. [26]Liu, X. & Padilla, W. J. Dynamic manipulation of infrared radiation with MEMS metamaterials. Advanced Optical Materials 1, 559-562 (2013).
  27. [27]Abb, M., Albella, P., Aizpurua, J. & Muskens, O. L. All-optical control of a single plasmonic nanoantenna–ITO hybrid. Nano letters 11, 2457-2463 (2011).DOI
  28. [28]Shen, Y., Hsu, C. W., Yeng, Y. X., Joannopoulos, J. D. & Soljačić, M. Broadband angular selectivity of light at the nanoscale: Progress, applications, and outlook. Applied Physics Reviews 3, 011103 (2016).DOI
  29. [29]Park, J. et al. All-solid-state spatial light modulator with independent phase and amplitude control for three-dimensional LiDAR applications. Nature nanotechnology 16, 69-76 (2021).DOI
  30. [30]Huang, Y.-W. et al. Gate-tunable conducting oxide metasurfaces. Nano letters 16, 5319-5325 (2016).DOI
  31. [31]Meng, C. et al. Dynamic piezoelectric MEMS-based optical metasurfaces. Science Advances 7, eabg5639 (2021).DOI
  32. [32]Siegel, J. et al. Electrostatic steering of thermal emission with active metasurface control of delocalized modes. Nature Communications 15, 3376 (2024).
  33. [33]Shayegan, K. J., Hwang, J. S., Zhao, B., Raman, A. P. & Atwater, H. A. Broadband nonreciprocal thermal emissivity and absorptivity. Light: Science & Applications 13, 176 (2024).DOI
  34. [34]Liu, M. et al. Broadband mid-infrared non-reciprocal absorption using magnetized gradient epsilon-near-zero thin films. Nature Materials, doi:10.1038/s41563-023-01635-9 (2023).DOI
  35. [35]Peter, Y. Y. & Cardona, M. Temperature coefficient of the refractive index of diamond- and zinc-blende-type semiconductors. Physical Review B 2, 3193 (1970).DOI
  36. [36]Gillen, G. D., DiRocco, C., Powers, P. & Guha, S. Temperature-dependent refractive index measurements of wafer-shaped InAs and InSb. Applied optics 47, 164-168 (2008).pubmed.ncbi.nlm.nih.gov/18188197
  37. [37]Law, S., Liu, R. & Wasserman, D. Doped semiconductors with band-edge plasma frequencies. Journal of Vacuum Science & Technology B 32 (2014).DOI
  38. [38]Lewi, T., Evans, H. A., Butakov, N. A. & Schuller, J. A. Ultrawide thermo-optic tuning of PbTe meta-atoms. Nano letters 17, 3940-3945 (2017).DOI
  39. [39]Rahmani, M. et al. Reversible thermal tuning of all-dielectric metasurfaces. Advanced Functional Materials 27, 1700580 (2017).DOI
  40. [40]Iyer, P. P., DeCrescent, R. A., Lewi, T., Antonellis, N. & Schuller, J. A. Uniform thermo-optic tunability of dielectric metalenses. Physical Review Applied 10, 044029 (2018).DOI
  41. [41]Iyer, P. P., Pendharkar, M., Palmstrøm, C. J. & Schuller, J. A. Ultrawide thermal free-carrier tuning of dielectric antennas coupled to epsilon-near-zero substrates. Nature communications 8, 472 (2017).DOI
  42. [42]Liberal, I. & Engheta, N. Near-zero refractive index photonics. Nature Photonics 11, 149-158 (2017).DOI
  43. [43]Vassant, S., Hugonin, J.-P., Marquier, F. & Greffet, J.-J. Berreman mode and epsilon near zero mode. Optics express 20, 23971-23977 (2012).DOI
  44. [44]Taliercio, T., Guilengui, V. N., Cerutti, L., Tournié, E. & Greffet, J.-J. Brewster “mode” in highly doped semiconductor layers: an all-optical technique to monitor doping concentration. Optics express 22, 24294-24303 (2014).
  45. [45]Jun, Y. C., Luk, T. S., Robert Ellis, A., Klem, J. F. & Brener, I. Doping-tunable thermal emission from plasmon polaritons in semiconductor epsilon-near-zero thin films. Applied Physics Letters 105, 131109 (2014).DOI
  46. [46]Rensberg, J. et al. Epsilon-near-zero substrate engineering for ultrathin-film perfect absorbers. Physical Review Applied 8, 014009 (2017).DOI
  47. [47]Yoon, J. et al. Broadband epsilon-near-zero perfect absorption in the near-infrared. Scientific reports 5, 1-8 (2015).DOI
  48. [48]Law, S., Adams, D., Taylor, A. & Wasserman, D. Mid-infrared designer metals. Optics express 20, 12155-12165 (2012).
  49. [49]Kane, E. O. Band structure of indium antimonide. Journal of Physics and Chemistry of Solids 1, 249-261 (1957).DOI
  50. [50]Byszewski, P., Kołodziejczak, J. & Zukotyński, S. The thermoelectric power in InSb in the presence of an external magnetic field. physica status solidi (b) 3, 1880-1884 (1963).
  51. [51]Varshni, Y. P. Temperature dependence of the energy gap in semiconductors. physica 34, 149-154 (1967).DOI
  52. [52]Vurgaftman, I., Meyer, J. & Ram-Mohan, L. R. Band parameters for III–V compound semiconductors and their alloys. Journal of applied physics 89, 5815-5875 (2001).
  53. [53]Kalem, S., Chyi, J. I., Morkoç, H., Bean, R. & Zanio, K. Growth and transport properties of InAs epilayers on GaAs. Applied physics letters 53, 1647-1649 (1988).DOI
  54. [54]Kalem, Ş. Molecular-beam epitaxial growth and transport properties of InAs epilayers. Journal of applied physics 66, 3097-3103 (1989).DOI
  55. [55]Costantini, D. et al. Plasmonic metasurface for directional and frequency-selective thermal emission. Physical Review Applied 4, 014023 (2015).

Paper details

vlnc:W_ya6sfnf8
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents