betaFeedback

WorksPhysics and Astronomy

Understanding the origin of the particularly small and anisotropic thermal expansion of MOF-74

Abstract

Metal-organic frameworks often display large positive or negative thermal expansion coefficients. MOF-74, a material envisioned for many applications does not display such a behavior. For this system, temperature-dependent x-ray diffraction reveals particularly small negative thermal expansion coefficients perpendicular and positive ones parallel to the hexagonally arranged pores. The observed trends are explained by combining state-of-the-art density-functional theory calculations with the Grüneisen theory of thermal expansion, which allows tracing back thermal expansion to contributions of individual phonons. On the macroscopic level, the small thermal expansion coefficients arise from two aspects: compensation effects caused by the large coupling between stress and strain perpendicular to the pores and the small magnitudes of the mean Grüneisen tensor elements, ⟨γ⟩\langleγ\rangle, which provide information on how strains in the material influence its phonon frequencies. To understand the small mean Grüneisen tensor in MOF-74, the individual mode contributions are analyzed based on the corresponding atomic motions. This reveals that only the lowest frequency modes up to ~3 THz provide non-negligible contributions, such that ⟨γ⟩\langleγ\rangle drops sharply at higher temperatures. These considerations reveal how the details of the anharmonic properties of specific phonon bands determine the magnitude and sign of thermal expansion in a prototypical material like MOF-74.

Introduction

Metal-organic frameworks (MOFs[1, 2, 3, 4]) are a booming class of porous materials with an enormous accessible surface area, often amounting to several thousand square meters per gram.[5, 6, 7] Therefore, MOFs have a high potential for applications such as gas storage,[8, 9, 10] catalysis,[11, 12, 13] and gas separation.[14, 15] They are also used in various functional devices.[16, 17, 18, 19, 20] In many of those applications, the thermal expansion of MOFs is a highly relevant property.[21, 22] For example, it determines the thermal mismatch (and the resulting thermal stresses)[23, 24, 25, 26] for heteroepitaxial growth processes,[27, 28] or the change of the pore volume with temperature. Therefore, considerable efforts have been dedicated to studying thermal expansion in MOFs by means of both simulations and experiments. Experimental studies have, for example, focused on isoreticular MOFs (IRMOFs),[29, 30, 31, 32] DUTs,[30, 33] HKUST-1,[30, 34] [35, 36] MOFs containing paddle-wheel secondary building units,[22, 30] [37] UiOs,[30] FMOF-1,[38] MCF-34,[39] ZIF-8,[40] MOF-74,[41] and others.[42–51] These experimental investigations are complemented by simulations, e.g., for IRMOFs,[21, 26] [52, 53, 54, 55] DUTs,[56] HKUST-1,[26] paddle-wheel MOFs,[30] MOF-74,[57] and others.[26] [56, 58, 59] For the meaning of the acronyms, we refer the reader to the respective references, as the detailed chemical nature of the above systems is not of immediate relevance for the following discussion. What is rather relevant is that these systems often show rather sizable linear and volumetric thermal expansion coefficients (either positive: PTE, or negative: NTE). This is shown in Figure 1. Notably, these thermal expansion coefficients in MOFs are usually much larger than for many common non-porous materials.[53,60,61] As a result, computational and experimental studies of thermal expansion in MOFs are typically concerned with explaining the origins of the large PTE and NTE coefficients.

Panels (a) and (b) showing linear and volumetric thermal expansion coefficients for several MOFs

Figure 1. Figure 1. (a) Linear and (b) volumetric thermal expansion coefficients for several MOFs reported in literature based on modelling (IRMOFs,[21, 26] [52, 53, 54, 55] DUTs,[56] HKUST-1,[26] paddle-wheel MOFs,[30] MOF-74,[57] and others[26] [56, 58, 59]) or experimental (IRMOFs,[29, 30, 31, 32] DUTs,[30, 33] HKUST-1,[30, 34] [35, 36] paddle-wheel MOFs,[22, 30] [37] UiOs,[30] FMOF-1,[38] MCF-34,[39] ZIF-8,[40] MOF-74 [41], and others[42–51]) studies. The colossal thermal expansion coefficients of FMOF-1 in nitrogen atmosphere (−1.3⋅10−2-1.3 \cdot10^{-2} and 1.2⋅10−21.2 \cdot10^{-2} in the abab-plane and in the cc-direction,[38] respectively) are not shown to enhance the visibility of the remaining MOF systems. The horizontal bars are drawn from the minimum to the maximum reported value of the respective MOF family, with vertical lines and hatched areas inside the colored bars representing individual values and ranges (e.g., upon varying linker lengths, adsorbates, topology, etc.) They have been taken from different papers and are reported for different crystallographic directions. The vertical red and blue lines in panel (a) denote the calculated linear thermal expansion coefficients (from the present work) for (activated) MOF-74(Zn) at 300 K in x(y)x(y)- (α11\alpha_{11}) and zz-direction (α33\alpha_{33}) at 300 K, respectively. The red line in panel (b) indicates the low volumetric thermal expansion coefficient, αV\alpha_{\mathrm{V}}, (at 300 K) calculated in this work.

For archetypical MOFs such as IRMOFs and HKUST-1, several relevant mechanisms and factors of influence have been identified. These are related to optical[29, 31, 32, 34] [55, 56] or acoustic[52] phonons, and potentially also to adsorbates,[54] where a correct treatment of anharmonicities in the potential energy surface has been shown to be crucial.[62] These considerations emphasize that studying thermal expansion is also an important first step towards understanding the anharmonic character of phonon modes in MOFs, which is relevant also for other properties like thermal conduction.[62–67] Particularly relevant quantities in this context are the so-called mode Grü­neisen parameters, which describe the relative changes of the frequencies of the individual phonon modes with the unit-cell volume (or the applied strain). These mode Grü­neisen parameters are directly connected to higher-order force constants beyond the harmonic approximation.[68–70] In this context, non-cubic MOFs are particularly interesting, as they allow studying the effects of anisotropic anharmonicities.

A practically relevant example of such an anisotropic system is zinc-based MOF-74,[71,72] which is in the focus of the present study. MOF-74 has been employed in different applications including colorimetric sensing,[73] adsorption chillers,[74] drug delivery,[75] and gas storage for, e.g., CO2\mathrm{CO}_{2}[76] and H2\mathrm{H}_{2}[9] [77]. When considering the thermal expansion of MOFs, MOF-74 shows comparably small linear expansion coefficients. Thus, MOF-74 can rather be defined as a low-thermal-expansion material (LTE). For reasons that will become apparent below, its volumetric thermal expansion coefficient is even lower at relevant temperatures, such that it lies in a similar range as certain ceramics often referred to as zero-thermal-expansion materials (ZTE).[78–82] This is consistent with existing “rough” theoretical estimates[57] (relying on a mixture of density-functional theory and force field calculations disregarding the anisotropy of the material). It is also in line with previous experimental findings for magnesium-based MOF-74,[41] which at room temperature suggest a positive thermal expansion coefficient of ∼6.7⋅10−6 K−1\sim6.7 \cdot10^{-6}\ \mathrm{K}^{-1} along the pore axis and a negative thermal expansion coefficient of ∼−1.5⋅10−6 K−1\sim-1.5 \cdot10^{-6}\ \mathrm{K}^{-1} perpendicular to it. This raises the question, which mechanisms are responsible for the close to ZTE behavior of MOF-74. The structure of MOF-74 comprises hexagonal channels with 1D metal-oxide secondary building units (SBUs) located at the corners of the hexagons and organic linkers forming the walls in between (see Figure 2). The physical properties of MOF-74 distinctly differ for directions along its pores and perpendicular to them. This is not surprising, considering that for the former the characteristics of the inorganic SBUs dominate, while for the latter the organic linkers play a much more prominent role.[57,64,83] The fundamental reasons for the LTE/ZTE behavior of MOF-74, however, remain unclear. The present study aims at changing that by identifying the origins of the LTE/ZTE behavior of pristine zinc-based MOF-74 at an atomistic level, with a particular focus on the material’s anisotropy. To this end, we combine diffraction studies with theoretical considerations based on state-of-the-art ab initio simulations within the framework of the Grüneisen theory of thermal expansion.[84] This approach (in contrast to, for example, molecular dynamics simulations) allows a phonon-resolved analysis of the situation such that one can assign to each phonon mode a quantitative contribution to the thermal expansion tensor. By analyzing the frequency ranges and wave vector-dependencies of the phonon bands with particularly relevant contributions, one is then able to identify trends and to systematically unravel the mechanisms behind the observed behavior.

The article is structured as follows: first, we briefly discuss the crystal structure of MOF-74 and provide the relevant synthetic, experimental, and theoretical details including a short summary of the Grüneisen theory of thermal expansion. Subsequently, the experimental results and their evaluation are discussed, followed by a detailed (phonon-resolved) analysis of the governing anharmonicities and contributions to the thermal expansion is presented. While the experiments yield observable thermal expansion values and represent a basis for the calculations, the simulations provide the desired mechanistic insights.

Methods

The Crystal Structure of MOF-74

The primitive crystallographic unit cell of MOF-74 with its three lattice vectors, a⃗n\vec{a}_n (n∈{1,2,3}n \in\{1,2,3\}), is shown in Figure 2. Although MOF-74 can be synthesized with a number of different metal ions,[85–91] with linkers consisting of more than one benzene ring,[72] and with modified docking groups,[92] whenever we refer to MOF-74 in the remainder of this article we mean pristine and activated MOF-74 based on Zn2+\mathrm{Zn}^{2+} ions connected by 2,5-dihydroxy-terephthalate linkers. The structure of MOF-74 belongs to space group Rˉ3\bar{R}3 (international number 148) and has a rhombohedral (trigonal) Bravais lattice. Unlike many other MOFs, MOF-74 forms one-dimensionally extended pores arranged in a honeycomb-like lattice. This results in a distinct structural anisotropy. Accordingly, also the metal (oxide) nodes consist of (infinitely extended) quasi-one-dimensional arrangements of Zn and O atoms. Note that in the activated (pristine) state, the Zn atoms in MOF-74 are undercoordinated, but still exhibit an (approximately) octahedral coordination geometry. Due to its rhombohedral symmetry, the lattice has two independent lattice parameters, aa and cc (from which the primitive lattice vectors are constructed as explained in the caption of Figure 2): The distance between the metal atoms along the zz-axis in the nodes equals cc, while the pore diameter in the xyxy-plane (i.e., the distance between two opposite corners of the hexagon) equals 4a/34a/3, as illustrated in Figure 2(a). Because of this distinct structural anisotropy, also the materials properties are expected to strongly depend on the crystallographic directions. This circumstance offers ideal conditions to separately study anharmonic effects in the zz-direction and in directions within the xyxy-plane. These can then be associated with the nodes (dominating in zz-direction) and the linkers of the MOF (relevant in the xyxy-plane).

In order to gain mechanistic insight and to qualitatively rationalize the signs of the mode Grüneisen tensor components in the Results section, we will analyze how certain geometric descriptors are impacted by the different phonons. This strategy is similar to the one used in Ref. [83], where such descriptors quantified the structural changes upon applying stress to the unit cell of MOF-74. The geometric descriptors include: the cross-sectional area of the nodes, AΔA_{\Delta}, defined by the projection of the centers of the Zn2+\mathrm{Zn}^{2+} ions onto the xyxy-plane, the inclination angle, ϕ\phi, between the edges of the nominal pore wall (i.e., the hypothetic regular hexagon connecting the centers of the nodes) and the projections of the linker backbones onto the xyxy-plane, the dihedral angle, τ\tau, between the COO−\mathrm{COO}^{-} group of the linker and the benzene ring, and the polar linker tilt angle, θ\theta, between the node axes and the long molecular axes of the linkers. The mentioned descriptors are schematically depicted in Figure 2(c) and (d). For more details about their definition see § 18 in the Supporting Information and Ref. [83].

Schematic depiction of the structural descriptors and crystallographic directions in the MOF

Figure 2.

Image not extracted

Figure 2 (PDF p. 7). (a) Top and (b) side view of the rhombohedral crystal structure of MOF-74 illustrating the two independent lattice parameters, aa and cc. The projections of the lattice vectors (a⃗n(\vec{a}_n with n=1,2,3)n=1,2,3) are shown as colored arrows. The lattice parameter aa is drawn in a way that it corresponds to the Cartesian xx-component of lattice vector a⃗1\vec{a}_1. The primitive Cartesian lattice vectors are constructed from aa and cc in the following way: a⃗1=[a,a/3,c]\vec{a}_1 = [a,a/\sqrt{3},c], a⃗2=[a,−a/3,c]\vec{a}_2 = [a,-a/\sqrt{3},c], and a⃗3=[0,−2a/3,c]\vec{a}_3 = [0,-2a/\sqrt{3},c]. The vertical dash-dotted line denotes the plane at which the structure is cut for the side view shown in panel (b), as seen in the direction of the black arrows. (b) Side view of the crystal structure illustrating the second independent lattice parameter cc as the Cartesian zz-component of all three lattice vectors. Atomic color coding: H…white, C…grey, O…red, Zn…purple. (c,d) Details of the structure of MOF-74 in which the most relevant geometric descriptors are shown: the cross-sectional area of the nodes, AΔA_{\Delta}, defined by the projection of the centers of the Zn2+\mathrm{Zn}^{2+} ions onto the xyxy-plane, the inclination angle, ϕ\phi, between the edges of the nominal pore wall (i.e., the hypothetic regular hexagon connecting the centers of the nodes; black horizontal line in panel (c)) and the projections of the linker backbones onto the xyxy-plane, the dihedral angle, τ\tau, between the COO−\mathrm{COO}^{-} group of the linker and the phenylene ring, and the polar linker tilt angle, θ\theta, between the node axes (parallel to the zz-axis) and the long molecular axes of the linkers (dash-dotted line).

Experimental Methods

The studied MOF-74 powder samples were obtained following the solvothermal synthesis protocols of [93]. Temperature-dependent x-ray diffraction (XRD) was used to study the pristine MOF. Prior to the XRD measurements, the samples were activated directly in the in-situ temperature chamber (TTK 600 from Anton Paar) by heating them to 300∘C300^{\circ}\mathrm{C} in vacuum (10−210^{-2} mbar) and keeping them at that temperature for 15 minutes. After the activation, the temperature was decreased stepwise, and x-ray diffractograms were recorded in Bragg-Brentano geometry using a PANalytical Empyrean diffractometer with a Cu radiation source, a primary Soller slit with a divergence angle of 0.02 rad, a divergence slit of 0.25∘0.25^{\circ}, a secondary 0.02 rad Soller slit, an anti-scatter slit with an angle of 0.25 rad, and an X’Celerator detector. To avoid a decrease in intensity, no additional monochromator was used, and to improve the thermal equilibration of the sample, a waiting time of up to 30 minutes was introduced between the time, when the internal sensor of the heating stage reached the set point temperature and when the XRD measurements were started. Furthermore, at each temperature the sample was aligned with respect to the x-ray beam to account for the thermal expansion of the setup.

The experimental results were analyzed using Bayesian probability theory to achieve meaningful results.94 This was necessary due to the very minor change of the structural parameters with temperature combined with average peak widths of 0.19°. Additionally, a statistical analysis also allowed to take into account uncertainties in the determination of the sample temperature. Finally, employing a probabilistic approach also enabled the determination of estimators for the uncertainty of the calculated results. A mathematically rigorous description of the employed approach can be found in § 9 in the Supporting Information.

Theoretical Methods

To generate the desired level of atomistic insight, ab initio calculations were carried out in the framework of density functional theory (DFT),95,96 employing the VASP97–100 code (version 5.4.4). Technically, these simulations were performed at 0 K (i.e., unlike in a molecular dynamics run, the atoms were kept fixed at their positions), but the temperature dependence of the phonon occupation and, thus, the thermal expansion tensor were accounted for, as described below. The exchange-correlation contributions were described via the PBEsol functional101,102 in combination with the D3-BJ103,104 a posteriori van der Waals correction. Additionally, tests employing the PBE functional105,106 are contained in § 11 and § 13 of the Supporting Information. Here it should not be concealed that they yield a different sign for the thermal expansion coefficient of the lattice parameter cc than when employing PBEsol. This is primarily a consequence of the fact that in MOF-74 one is dealing with overall very small effects. As discussed in § 13 of the Supporting Information, the origin of the observation can be traced back to qualitatively different, small changes of certain geometric descriptors with strain or phonon displacements that we observe for the two functionals. In this context, it should, however, be stressed that PBEsol is supposed to yield more accurate structural properties101,102,107 and thermal expansion coefficients70,108,109 for solids (with smaller charge density gradients). Thus, the vast majority of studies calculating thermal expansion coefficients within DFT typically relies on the PBEsol functional. Moreover, only PBEsol yields results that are consistent with the most probable outcome of our experiments (see below) and with the neutron diffraction data of the Mg-analogue of MOF-74 in Ref. [41]. Finally, as again shown in § 10 of the Supporting Information, only with PBEsol qualitatively consistent trends between the most sophisticated calculations performed within the quasi-harmonic approximation and in the framework of the Grüनेisen Theory of thermal expansion are obtained.

Therefore, in the main manuscript we will exclusively focus on the results of the PBEsol calculations.

In the simulations, we first optimized the crystal structure of the primitive unit cell (including lattice parameters) to maximum residual forces below 11 meV/Å using a 3×3×33 \times3 \times3 kk-mesh and a plane wave energy cutoff of 10001000 eV for the optimization of the lattice constants and atomic positions. The elastic tensor and the compliance tensor were calculated according to the approach described in Ref. [83] and in § 11 of the Supporting Information, keeping the particularly high cutoff energy of 10001000 eV, following the convergence studies shown in Ref. [83]). Based on careful and extensive convergence tests discussed in § 11 of the Supporting Information, we employed a 1×1×31 \times1 \times3 supercell of the conventional unit cell for the subsequent phonon calculations. This hexagonal supercell contains 9 primitive unit cells, as shown in § 12.1 in the Supporting Information. As a consequence of the supercell size, its electronic structure had to be sampled only at the Γ\Gamma-point to achieve convergence. An advantage of the conventional unit cell is that it allows to probe the interatomic force constants more efficiently in real space, since a corresponding 1×1×31 \times1 \times3 supercell has approximately the same unit-cell extents along all directions. For the phonon calculations, due to the enormous system size of the supercells, the plane wave energy cutoff was reduced to 800800 eV (which required a reoptimization of the atomic positions with this cutoff, which was done for the primitive unit cell with a 3×3×33 \times3 \times3 kk-mesh, see § 11 in Supporting Information). In all simulations, an energy convergence criterion of 10−810^{-8} eV for the self-consistency cycle, and a Gaussian smearing of the electronic states with a width of 0.050.05 eV were employed.

For the chosen way of incorporating temperature (entropy) effects into the thermodynamic considerations, one first requires the phonon band structures of the material. For those phonon band structure calculations, we used the phonopy[110] package (version 2.9.1) and sampled the first Brillouin zone with a 20×20×2020 \times20 \times20 mesh of phonon wave vectors, qq, when calculating thermodynamic properties.

When following the evolution of the above-defined geometrical descriptors as a function of strain, we consider two distinct situations: (i) uniaxial strain parallel to the pore (i.e., in zz-direction) and (ii) isotropic strain perpendicular to the pore (i.e., in the xyxy-plane). The latter is a more realistic scenario than applying uniaxial strain in either xx- or yy-direction because in the absence of external stresses, the thermal strain is isotropic in the xyxy-plane for a system with rhombohedral symmetry.

For the visualization of the crystal structure and of phonon modes, as well as for recording the corresponding animations, the Ovito package (version 3.3.1) was used.[111]

Anisotropic Thermal Expansion

One possible strategy for computing the thermal expansion tensor of a material would be to calculate the temperature-dependent (non-equilibrium) total Gibbs free enthalpy, GG, (i.e., the contributions from electrons, phonons, and the elastic energy due to externally applied stress[112–114]) for various combinations of lattice constants. Then, at each temperature, one could identify the set of lattice constants, which minimizes the free enthalpy at each temperature to determine the thermal expansion coefficients. This minimization is typically achieved by fitting an analytical function (such as the well-known equations of state of Birch,[115] Murnaghan,[116] or Vinet et al.[117]) to the free enthalpy-vs.-lattice constants data and taking the minimum of the model function (which were systematically compared in Refs. [118,119]). This approach is commonly referred to as the quasi-harmonic approximation (QHA).[70,120,121] We have applied several flavors of this approach to the case of MOF-74, as discussed in Section S3 of the Supporting Information, including the procedure followed by George et al.[122] for several organic crystals and the approach by Holec et al.[123] who incorporated the anisotropy at a more sophisticated level. Overall, the results of the common QHA-based approaches sensitively depend on fitting and minimizing Gibbs free enthalpies with respect to finite strains. For thermal expansion coefficients as small as the ones encountered in MOF-74, the changes in the free enthalpy become, however, so small that fitting a model function and finding the associated minima (relying on well-established routines of the numpy,[124] scipy,[125] or scikit-learn[126] packages) becomes numerically stable only for applied strains much larger than the thermal strains suggested by our experiments. This means, for realistically small strains, the QHA fitting and minimization becomes highly inaccurate, while for unrealistically large strains, the results obtained within the QHA overestimate the thermal expansion especially for the lattice parameter cc (see the extensive discussion in Section S3 of the Supporting Information). In the case of MOF-74, we, therefore, resorted to the Grüneisen theory of thermal expansion,[84] which in combination with the PBEsol functional yields results in rather good qualitative and also quantitative agreement with the experimental observations, as shown below. The central quantity in the Grün­eisen theory is the mode Grüneisen tensor, γijλ\gamma_{ij}^{\lambda} (Cartesian components i,j∈{1=x,2=y,3=z}i,j \in\{1=x, 2=y, 3=z\}). It is defined as the (negative) first derivative of the phonon frequency, ω\omega, with respect to the components of the strain tensor, ϵij\epsilon_{ij}, for each phonon mode, λ\lambda (as indicated by super- and subscripts):[68,70,127]

γijλ=−1ωλ∂ωλ∂εij(1)\gamma_{ij}^{\lambda}=-\frac{1}{\omega_{\lambda}}\frac{\partial\omega_{\lambda}}{\partial\varepsilon_{ij}} \tag*{(1)}

In practice, the partial derivatives in Equation (1) are determined based on the derivatives of the dynamical matrix (at 0 K), which are approximated by finite differences (see § 10.7 in the Supporting Information). Hence, it is necessary to calculate the dynamical matrix for the equilibrium unit cell at 0 K as well as the dynamical matrices for suitably strained cells. In order to improve the numerical accuracy in the calculation of the finite differences, we implemented a more accurate fourth-order finite difference scheme, as detailed in § 10.7 of the Supporting Information, where also the choice of 10−310^{-3} for the strain step size is briefly motivated.

Based on the mode Grüneisen tensors, one can calculate the temperature-dependent mean Grüneisen tensor, ⟨γij⟩\langle\gamma_{ij}\rangle, employing Equation (2). It can be interpreted as the average value of γijλ\gamma_{ij}^{\lambda} weighted with the phonon mode contributions to the heat capacity (in the grand-canonical ensemble), cvλc_{\mathrm{v}}^{\lambda}, at a specific temperature, TT:

⟨γij⟩(T)=∑λcvλ(T)γijλ∑λcvλ(T)(2)\langle\gamma_{ij}\rangle(T)=\frac{\sum_{\lambda}c_{\mathrm{v}}^{\lambda}(T)\gamma_{ij}^{\lambda}}{\sum_{\lambda}c_{\mathrm{v}}^{\lambda}(T)} \tag*{(2)}

Note that the temperature dependence of ⟨γij⟩\langle\gamma_{ij}\rangle arises solely from the temperature dependence of the mode contributions to the heat capacity, while, at the same time, the (0 K-) mode Grüneisen tensors are used.

Finally, the thermal expansion tensor, αij\alpha_{ij}, is directly related to ⟨γij⟩\langle\gamma_{ij}\rangle, to the compliance tensor, SijklS_{ijkl}, and to the phonon heat capacity per volume, CV/VC_{\mathrm{V}}/V, according to Equation (3) [70].

αij=CVV∑klSijkl⟨γkl⟩(3)\alpha_{ij}=\frac{C_{\mathrm{V}}}{V}\sum_{kl}S_{ijkl}\langle\gamma_{kl}\rangle \tag*{(3)}

A derivation of this equation is contained in § 10.7 the Supporting Information. In contrast to the situation in cubic materials, the entire compliance tensor rather than the (inverse) bulk modulus enters Equation (3), such that the crystal anisotropy is considered when (thermal) stresses lead to (anisotropic) strains. In contrast to QHA-based approaches (see § 10 in the Supporting Information), one cannot readily predict the temperature dependence of the compliance tensor with the Grüneisen theory. In fact, considering the variation of SijklS_{ijkl} with temperature would drastically increase the complexity of the calculations, making them prohibitively expensive for sophisticated ab initio methods. To avoid resorting to a lower level of theory, we, thus, used the compliance tensor obtained from precise DFT-calculations of the 0 K-structure. Consequently, the temperature dependence of the thermal expansion tensor is approximated to arise solely from the numerator of Equation (2) (as the denominator cancels with the heat capacity in Equation (3)). Neglecting the temperature dependence of the compliance tensor is a drawback of the Grüneisen theory of thermal expansion, but it makes it possible to rely on accurate ab initio calculations. Moreover, since MOF-74 is an LTE/ZTE material [41,57], the assumption of a negligible temperature dependence of SijklS_{ijkl} appears well justified.

One of the distinct advantages of the Grüneisen theory of thermal expansion is its ability to provide information on the contributions of specific phonon modes, λ\lambda, to the thermal expansion tensor. These mode contributions, αijλ\alpha_{ij}^{\lambda}, can be defined in a straightforward manner by combining the thermal averaging of the Grüneisen tensor in Equation (2) with the general expression for α\alpha in Equation (3). This yields Equation (4) and (5), which define the mode contributions to αij\alpha_{ij}. They depend on the compliance tensor, the mode Grüneisen tensor, γijλ\gamma_{ij}^{\lambda}, and the mode contribution to the phonon heat capacity, cνλc_{\nu}^{\lambda} (with NqN_q being the number of wave vectors used to sample reciprocal space):

αij(T)=1Nq∑λαijλ(T)(4)\alpha_{ij}(T)=\frac{1}{N_q}\sum_{\lambda}\alpha_{ij}^{\lambda}(T) \tag*{(4)}

with

αijλ(T)=1V∑klSijklcνλ(T)γklλ(5)\alpha_{ij}^{\lambda}(T)=\frac{1}{V}\sum_{kl}S_{ijkl}c_{\nu}^{\lambda}(T)\gamma_{kl}^{\lambda} \tag*{(5)}

References

  1. [1]von der Linden, W.; Dose, V.; Toussaint, U. von Bayesian Probability Theory: Applications in the Physical Sciences; Cambridge University Press, 2014;
  2. [2]Gross, R.; Marx, A. Festkörperphysik; Oldenbourg Wissenschaftsverlag, 2012; ISBN 9783486712940.
  3. [3]Kittel, C. Introduction to Solid State Physics; Wiley: New York, 2004; ISBN 9780471415268.
  4. [4]Ritz, E.T.; Li, S.J.; Benedek, N.A. Thermal expansion in insulating solids from first principles. J. Appl. Phys. 2019, 126, doi:10.1063/1.5125779.DOI
  5. [5]R.S. Krishnan R. Srinivasan, S.D.; Pamplin, B.R. Thermal Expansion of Crystals; Pergamon Press, 1979; ISBN 9780080214054; 0080214053.
  6. [6]Wallace, D.C.; Callen, H. Thermodynamics of Crystals. Am. J. Phys. 2005, 40, 1718–1719.
  7. [7]Angel, R.J.; Murri, M.; Mihailova, B.; Alvaro, M. Stress , strain and Raman shifts. Zeitschrift für Krist. - Cryst. Mater. 2019, 234, 129–140, doi:https://doi.org/10.1515/zkri-2018-2112.
  8. [8]Nolting, W. Grundkurs Theoretische Physik 6 - Statistische Physik; 7th ed.; Springer Spektrum: Berlin Heidelberg, 2014; ISBN 978-3-642-25392-8.
  9. [9]Ziman, J.M. Electrons and Phonons: The Theory of Transport Phenomena in Solids; Oxford University Press: Oxford, 2001; ISBN 9780198507796.
  10. [10]Baroni, S.; de Gironcoli, S.; Dal Corso, A.; Giannozzi, P. Phonons and related crystal properties from density-functional perturbation theory. Rev. Mod. Phys. 2001, 73, 515–562, doi:10.1103/RevModPhys.73.515.
  11. [11]Murnaghan, F.D. Finite Deformations of an Elastic Solid. Am. J. Math. 1937, 59, 235–260.DOI
  12. [12]Birch, F. Finite Elastic Strain of Cubic Crystals. Phys. Rev. 1947, 71, 809–824, doi:10.1103/PhysRev.71.809.DOI
  13. [13]Vinet, P.; Smith, J.R.; Ferrante, J.; Rose, J.H. Temperature effects on the universal equation of state of solids. Phys. Rev. B 1987, 35, 1945–1953, doi:10.1103/PhysRevB.35.1945.DOI
  14. [14]Katsura, T.; Tange, Y. A simple derivation of the Birch-Murnaghan equations of state (EOSs) and comparison with those derived from other definitions of finite strain. Minerals 2019, 9, doi:10.3390/min9120745.DOI
  15. [15]Latimer, K.; Dwaraknath, S.; Mathew, K.; Winston, D.; Persson, K.A. Evaluation of thermodynamic equations of state across chemistry and structure in the materials project. npj Comput. Mater. 2018, 4, 1–7, doi:10.1038/s41524-018-0091-x.DOI
  16. [16]George, J.; Wang, R.; Englert, U.; Dronskowski, R. Lattice thermal expansion and anisotropic displacements in urea, bromomalonic aldehyde, pentachloropyridine, and naphthalene. J. Chem. Phys. 2017, 147, 074112, doi:10.1063/1.4985886.DOI
  17. [17]Holec, D.; Abdoshahi, N.; Mayer, S.; Clemens, H. Thermal expansion and other thermodynamic properties of α2-Ti3Al and γ-TiAl intermetallic phases from first principles methods. Materials (Basel). 2019, 12, 1–11, doi:10.3390/ma12081292.DOI
  18. [18]Pedregosa, F.; Varoquaux, G.; Gramfort, A.; Michel, V.; Thirion, B.; Grisel, O.; Blondel, M.; Prettenhofer, P.; Weiss, R.; Dubourg, V.; et al. Scikit-learn: Machine Learning in Python. J. Mach. Learn. Res. 2011, 12, 2825–2830.arxiv.org/abs/1201.0490
  19. [19]Togo, A.; Tanaka, I. First principles phonon calculations in materials science. Scr. Mater. 2015, 108, 1–5, doi:10.1016/j.scriptamat.2015.07.021.DOI
  20. [20]Harris, C.R.; Millman, K.J.; van der Walt, S.J.; Gommers, R.; Virtanen, P.; Cournapeau, D.; Wieser, E.; Taylor, J.; Berg, S.; Smith, N.J.; et al. Array programming with {NumPy}. Nature 2020, 585, 357–362, doi:10.1038/s41586-020-2649-2.DOI
  21. [21]Virtanen, P.; Gommers, R.; Oliphant, T.E.; Haberland, M.; Reddy, T.; Cournapeau, D.; Burovski, E.; Peterson, P.; Weckesser, W.; Bright, J.; et al. {SciPy} 1.0: Fundamental Algorithms for Scientific Computing in Python. Nat. Methods 2020, 17, 261–272, doi:10.1038/s41592-019-0686-2.DOI
  22. [22]Kresse, G.; Marsman, M.; Furthmüller, J. VASP the Guide Available online: https://cms.mpi.univie.ac.at/vasp/vasp.pdf (accessed on Apr 3, 2019).
  23. [23]Grimme, S.; Antony, J.; Ehrlich, S.; Krieg, H. A consistent and accurate ab initio parametrization of density functional dispersion correction (DFT-D) for the 94 elements H-Pu. J. Chem. Phys. 2010, 132, 154104, doi:10.1063/1.3382344.DOI
  24. [24]Grimme, S.; Ehrlich, S.; Goerigk, L. Effect of the damping function in dispersion corrected density functional theory. J. Comput. Chem. 2011, 32, 1456–1465, doi:10.1002/jcc.21759.DOI
  25. [25]Perdew, J.P.; Burke, K.; Ernzerhof, M. Generalized Gradient Approximation Made Simple. Phys. Rev. Lett. 1996, 77, 3865–3868, doi:10.1103/PhysRevLett.77.3865.DOI
  26. [26]Perdew, J.P.; Burke, K.; Ernzerhof, M. Generalized Gradient Approximation Made Simple [Phys. Rev. Lett. 77, 3865 (1996)]. Phys. Rev. Lett. 1997, 78, 1396, doi:10.1103/PhysRevLett.78.1396.DOI
  27. [27]Perdew, J.P.; Ruzsinszky, A.; Csonka, G.I.; Vydrov, O.A.; Scuseria, G.E.; Constantin, L.A.; Zhou, X.; Burke, K. Restoring the density-gradient expansion for exchange in solids and surfaces. Phys. Rev. Lett. 2008, 100, 1–4, doi:10.1103/PhysRevLett.100.136406.DOI
  28. [28]Perdew, J.P.; Ruzsinszky, A.; Csonka, G.I.; Vydrov, O.A.; Scuseria, G.E.; Constantin, L.A.; Zhou, X.; Burke, K. Erratum: Restoring the Density-Gradient Expansion for Exchange in Solids and Surfaces [Phys. Rev. Lett. 100, 136406 (2008)]. Phys. Rev. Lett. 2009, 102, 39902, doi:10.1103/PhysRevLett.102.039902.DOI
  29. [29]Kamencek, T.; Zojer, E. Understanding the Anisotropic Elastic Properties of Metal–Organic Frameworks at the Nanoscale: The Instructive Example of MOF-74. J. Phys. Chem. C 2021, 125, 24728–24745, doi:10.1021/acs.jpcc.1c07882.DOI
  30. [30]Kamencek, T.; Bedoya-Martínez, N.; Zojer, E. Understanding phonon properties in isoreticular metal-organic frameworks from first principles. Phys. Rev. Mater. 2019, 3, 116003, doi:10.1103/PhysRevMaterials.3.116003.DOI
  31. [31]Stukowski, A. Visualization and analysis of atomistic simulation data with OVITO-the Open Visualization Tool. Model. Simul. Mater. Sci. Eng. 2010, 18, 015012, doi:10.1088/0965-0393/18/1/015012.DOI
  32. [32]Wang, X.; Guo, R.; Xu, D.; Chung, J.; Kaviany, M.; Huang, B. Anisotropic Lattice Thermal Conductivity and Suppressed Acoustic Phonons in MOF-74 from First Principles. J. Phys. Chem. C 2015, 119, 26000–26008, doi:10.1021/acs.jpcc.5b08675.
  33. [33]Csonka, G.I.; Perdew, J.P.; Ruzsinszky, A.; Philipsen, P.H.T.; Lebègue, S.; Paier, J.; Vydrov, O.A.; Ångyán, J.G. Assessing the performance of recent density functionals for bulk solids. Phys. Rev. B - Condens. Matter Mater. Phys. 2009, 79, 1–14, doi:10.1103/PhysRevB.79.155107.DOI
  34. [34]Queen, W.L.; Brown, C.M.; Britt, D.K.; Zajdel, P.; Hudson, M.R.; Yaghi, O.M. Site-specific CO 2 adsorption and zero thermal expansion in an anisotropic pore network. J. Phys. Chem. C 2011, 115, 24915–24919, doi:10.1021/jp208529p.DOI

Paper details

vlnc:W_yjvr7hyj
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents