betaFeedback

WorksPhysics and Astronomy

Progress on the MALTA CMOS Sensor: Edge-TCT Measurements for Parametric Pixel Simulation

Abstract

MALTA2 is a monolithic active pixel sensor, developed in the 180 nm CMOS imaging technology for radiation-hard applications in high-rate environments. This contribution summarizes recent developments in the characterization and simulation of MALTA2. The charge collection of a sensor on epitaxial silicon is studied with the Edge Transient Current Technique (Edge-TCT), using a digital readout, where the charge is reconstructed solely from binary hit data. In previous works, only specially designed analog output pixels at the matrix periphery were investigated. In contrast, the digital readout gives access to the full edge of the pixel matrix. Laser scans across neighboring pixels enable a two-dimensional parameterization of the charge collection. This parameterization serves as input to a parametric pixel simulation, which has been developed for chip design optimization and system-level studies. The simulation results are validated with test beam data.

34th International Workshop on Vertex Detectors (VERTEX2026)

20-24 July 2026

Stoos, Switzerland

Introduction

Future tracking detectors in high-energy physics demand improvements in sensor technologies. Monolithic active pixel sensors (MAPS) have already demonstrated such improvements over hybrid detectors in terms of lower material budget, higher granularity and lower power consumption. However, further development is needed for MAPS application in environments with high hit rates and radiation levels [1]. The MALTA2 sensor addresses both requirements. Its design in the 180 nm Tower CMOS imaging process features a small n-type collection electrode in each pixel for low capacitance and noise. An asynchronous readout architecture provides a time resolution of 2 ns for hit rates up to 100 MHz/cm2100\,\mathrm{MHz}/\mathrm{cm}^{2} [2]. On a Czochralski substrate, the sensor is fully efficient up to fluences of 3×1015 1 MeV neq/cm23 \times10^{15}\,\mathrm{1\,MeV\,n_{eq}}/\mathrm{cm}^{2}. Increased doping concentrations are being investigated to compensate for irradiation effects.

The optimization of sensors and detectors requires a simulation that is fast and realistic. This work follows a data-driven approach, that does not rely on proprietary information or assumptions about the fabrication, such as doping profiles and implant sizes. Instead, the charge collection efficiency of MALTA2 is measured directly and modeled for use in simulation. For this purpose, the sensor edge is scanned with an infrared laser using the Edge transient current technique (Edge-TCT).

Section 2 presents the setup and the charge reconstruction from digital hit data. From these measurements, a model for the charge collection is derived in section 3. The model serves as input to the parametric simulation summarized in section 4, which is validated with test beam data.

Digital Edge-TCT

A MALTA2 sensor is wire-bonded to a dedicated PCB for Edge-TCT, as shown in Figure 1a. It allows scanning of the polished sensor edge [3]. The sensor has a 30 μ\mum thick epitaxial layer grown on a p-type substrate and each pixel contains a front-end that digitizes a hit above threshold. TCT measurements with such a digital readout have previously been demonstrated for other MAPS that are illuminated through the backside [4]. Here, as illustrated in Figure 1b, an infrared laser (λ=1064 nm)(\lambda= 1064\ \mathrm{nm}) is focused through the edge and induces a signal in multiple pixels along the beam (Y-direction). Its wavelength corresponds to an absorption length of 1 mm in silicon at room temperature [5]. The laser intensity is therefore approximately constant within a single pixel pitch of 36.4 μm\mu\mathrm{m}. The laser is set to deposit about 350 e−e^{-} per pixel, corresponding to about 10 e−e^{-} per μm\mu\mathrm{m}, a factor of six lower than for a minimum-ionizing particle. This charge lies within the threshold range of 100 to 400 e−e^{-} at the standard gain setting, which is necessary for the charge reconstruction.

Figure 1. (a) Photo of a MALTA2 sensor wire-bonded to a PCB designed for Edge-TCT. The 1064 nm laser is focused on the polished sensor edge as illustrated in (b). (c) shows the hits as a function of threshold from the top eight pixels of the same column (Y = 0 to 7). All other rows are masked.

Charge reconstruction from digital data

The charge is reconstructed by measuring the number of hits as a function of the discriminator threshold, as shown in Figure 1c for pixels located in the same column. The top eight pixels of the column (0≤Y≤70 \le Y \le7) are scanned simultaneously, while all other pixels (Y≥8Y \ge8) are masked to reduce the data rate. Each threshold is scanned for 10 ms at a laser pulse frequency of 50 kHz. At low thresholds, all 500 pulses are registered. Once the threshold exceeds the signal amplitude, the number of hits decreases. The amplitude of each pixel is therefore reconstructed as the 50% occupancy point of an error-function fit. The amplitude generally decreases with the Y-coordinate, because the laser is absorbed in the silicon along the beam. An exception is the first row (Y=0Y = 0), in which the pixels show a systematically lower amplitude in all scans. These pixels have a reduced charge collection due to their location near the edge of the sensor. The second row of pixels (Y=1Y = 1) features the largest amplitude and is assumed to be representative of the pixel matrix. This row is selected for the following scans.

Two-dimensional scan

Figure 2a illustrates a 2D scan across the sensor edge (X-Z plane). The laser is moved in 2 μm\mu\mathrm{m} steps and the collected charge is reconstructed at each step. The result is shown in Figure 2b for three adjacent pixels in the row Y=1Y = 1. The high charge regions of the individual pixels are distinguished in the epitaxial layer and reach a maximum charge of 350 e−e^{-}. For each pixel, a contour line marks the interpolated 50% level relative to its maximum charge. These contours coincide at the pixel boundaries, as expected from equal charge sharing without significant charge losses. The equal charge sharing is supported by the projections onto the X-axis in the bottom panel, which intersect at the pixel boundaries at 50%. Such a direct measurement of charge sharing is performed for the first time for MALTA2. The digital readout permits the simultaneous measurement of neighboring pixels, whereas an analog test pixel can only be studied individually.

Figure 2. Illustration (a) and measurement (b) of a laser scanning the sensor edge. The charge is reconstructed from digital data and shows the collection profile. The contours represent the 50% level of each pixel relative to its maximum charge. The individual pixel contributions are shown in the X-axis projection.

The bottom panel of Figure 2b shows a feature of the digital readout at X = 0 μ\mum, the boundary of two pixels. A reconstructed charge appears in the third pixel (dashed violet line), far outside its geometric region. This is attributed to the digital merging of hits that arrive within a 1.6 ns time window. The merging can shift a hit to another pixel coordinate. The merging effect as well as its design optimization is discussed in detail in ref. [6]. Merging is mitigated in the design of MALTA3, the next sensor generation. Since the displaced hits lie outside the geometric region of the pixel, they are excluded from the charge collection study.

The 2D charge map of the central pixel is used to quantify its sensitive area, defined as the area in which the charge exceeds a given threshold (Figure 3a). The area decreases continuously with threshold and vanishes once the threshold reaches the maximum charge. At half maximum (red dotted line), it agrees with the expectation from a fully depleted epitaxial layer (gray dotted line). At lower thresholds, the area exceeds the nominal pixel area due to charge sharing from neighboring pixels. This threshold dependence is relevant for grazing-angle studies, which reconstruct a depletion depth from the cluster size. The reconstructed depth decreases with threshold, as observed in ref. [3], because the sensitive area decreases. The following section derives a charge collection model from the measurement.

Figure 3. (a) Sensitive area of a pixel versus detection threshold. (b) 1D scan along the X-dimension. Figure 3: (a) quantifies the area inside a contour at different thresholds. It matches the expectation at half maximum. The scan in (b) goes through the pixel center. The charge collection model (red dashed line) describes the data when convolved with the laser beam width σgauss\sigma_{\mathrm{gauss}} (blue line). The error bars represent the uncertainty from charge calibration.

Charge collection model

To parameterize the charge collection, a pixel is scanned in 1 µm steps along the X-dimension through its center (Z=15Z = 15 µm), as shown in Figure 3b. The collected charge is modeled as a function of the position xx relative to the pixel by

CC⁡(x;C,σerf,FWHM)=C2[erf⁡(xσerf)−erf⁡(x−FWHMσerf)].(1)\operatorname{CC}(x; C, \sigma_{\mathrm{erf}}, \mathrm{FWHM}) = \frac{C}{2} \left[\operatorname{erf}\left(\frac{x}{\sigma_{\mathrm{erf}}}\right) - \operatorname{erf}\left(\frac{x-\mathrm{FWHM}}{\sigma_{\mathrm{erf}}}\right)\right]. \tag*{(1)}

CC is a normalization constant and σerf\sigma_{\mathrm{erf}} the width of the error-function at the pixel edges. The distance between the two edges is the full width at half maximum (FWHM). The charge collection model (red dashed line) is convolved with a Gaussian distribution, which accounts for the smearing due to the width of the laser beam σgauss=4.1\sigma_{\mathrm{gauss}} = 4.1 µm. The convolution (blue line) is fitted to the data. All three model parameters are left free in the fit. The deviation between data and fit is well contained within the 3% uncertainty of charge calibration [7]. The fit describes the data well at both edges and yields σerf=4.2±0.6\sigma_{\mathrm{erf}} = 4.2 \pm0.6 µm. The FWHM of 36.9±0.336.9 \pm0.3 µm is close to the nominal pixel pitch of 36.4 µm. To test whether this pixel is representative, the same fit is performed for more than one hundred pixels. The results are compatible, with a mean and standard deviation of σerf=4.4±0.7\sigma_{\mathrm{erf}} = 4.4 \pm0.7 µm. Both values agree with an independent charge collection measurement using minimum-ionizing particles at the CERN SPS, which yielded a width of 4.3±0.34.3 \pm0.3 µm [8]. Thus, the laser and test beam measurements are consistently modeled by eq. (1), which serves as input to the parametric simulation.

Parametric simulation

The charge collection model is the main input to the simulation [6]. It distributes a charge deposition in Geant4 [9] among the seed pixel and its neighbors according to eq. (1), evaluated as CC⁡(x;C=1,σerf=4.3 μm,FWHM=36.4 μm)\operatorname{CC}(x; C = 1, \sigma_{\mathrm{erf}} = 4.3\ \mathrm{\mu m}, \mathrm{FWHM} = 36.4\ \mathrm{\mu m}). Figure 4a illustrates these fractions for the seed pixel (red line) and its neighbors (dashed lines). Near the pixel boundaries (vertical gray lines), up to 50% of the charge is shared with a neighbor. The same model is applied in the Y-dimension, which leads to the 2D charge collection in Figure 4b. In addition to charge sharing, the simulation incorporates the time walk of the front-end and the digital readout logic.

Figure 4. Charge collection efficiency along the pitch dimension. (a) shows the model of a seed pixel and its two neighbors in the X-dimension. It is defined by eq. (1). (b) illustrates the symmetric 2D model for the seed pixel.

The simulation is validated with test beam data measured at the CERN SPS. Charged hadrons of 120 GeV/c120\,\mathrm{GeV}/c are incident on the front of the sensor. While the typical operational threshold is 200 e−200\,e^{-} it can be raised up to 2000 e−2000\,e^{-}. Figure 5 compares efficiency and cluster size as a function of threshold. Simulation and data agree within the threshold uncertainty, which is represented by the uncertainty band. Additionally, the simulation reproduces the measured in-pixel profiles of efficiency and cluster size, as discussed in detail in ref. [6]. This validates the accuracy of the simulation across the full threshold range.

Figure 5. Data and simulation are compared for the efficiency (a) and cluster size (b) of a MALTA2 sensor. The uncertainty band represents the threshold uncertainty of 3%.

Conclusion

Digital Edge-TCT is a practical tool for characterizing multiple pixels of a MAPS. Since it makes use of the standard digital readout, it does not require dedicated analog test pixels or an oscilloscope. For MALTA2, the charge collection is reconstructed from binary hit data and modeled by error-functions with a width of about 4 μm4\,\mu\mathrm{m} at the pixel edges. This model is the input to a parametric simulation, which reproduces the measured efficiency and cluster size over a wide threshold range. The simulation is currently used to investigate the application of MALTA2 in larger detector geometries and to optimize the readout for a new sensor design.

Acknowledgments

This project has received funding from the European Union’s Horizon 2020 Research and Innovation programme under Grant Agreement numbers: 101004761 (AIDAinnova), 675587 (STREAM), 654168 (AIDA-2020).

References

  1. [1]W. Snoeys, Monolithic CMOS Sensors for high energy physics - Challenges and perspectives, Nucl. Instrum. Meth. A 1056 (2023) 168678.
  2. [2]M. van Rijnbach et al., Radiation hardness of MALTA2 monolithic CMOS imaging sensors on Czochralski substrates, Eur. Phys. J. C 84 (2024) 251.
  3. [3]D. V. Berlea et al., Depletion depth studies with the MALTA2 sensor, a depleted monolithic active pixel sensor, Nucl. Instrum. Meth. A 1063 (2024) 169262.
  4. [4]C. Pantouvakis et al., Pixel response characterization of the ARCADIA fully depleted MAPS, JINST 21 (2026) P04003.DOI
  5. [5]M. Green, Self-consistent optical parameters of intrinsic silicon at 300 K including temperature coefficients, Sol. Energy Mater. Sol. Cells 92 (2008) 1305-10.DOI
  6. [6]D. V. Berlea et al., Design optimization of MAPS-based detectors using a data-driven fast simulation approach, Eur. Phys. J. C 86 (2026) 890.
  7. [7]L. Fasselt et al., Charge calibration of MALTA2, a radiation hard depleted monolithic active pixel sensor, Nucl. Instrum. Meth. A 1082 (2026) 170972.DOI
  8. [8]L. Fasselt et al., Charge collection parameterization of MALTA2, a depleted monolithic active pixel sensor, JINST 21 (2026) C04001.arxiv.org/abs/2602.23139
  9. [9]S. Agostinelli et al., GEANT4—a simulation toolkit, Nucl. Instrum. Meth. A 506 (2003) 250.DOI

Paper details

vlnc:W_ypy2dzcn
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents