betaFeedback

WorksPhysics and Astronomy

Uniaxial negative thermal expansion in a tetragonal V3S-type superconductor IrZr3

Abstract

Recently, uniaxial negative thermal expansion (NTE) has been observed in transition-metal zirconides including tetragonal (CuAl2-type) CoZr2 and orthorhombic (Re3B-type) CoZr3. Here, we report the observation of uniaxial NTE in tetragonal (V3S-type) IrZr3. With increasing temperature, the lattice parameter for the a-axis and volume of IrZr3 increase, but the lattice parameter for the c-axis decreases. IrZr3 is a superconductor with a transition temperature of 2.3 K. The present result suggests that uniaxial NTE and related anomalous axis thermal expansion occur in various transition-metal zirconides, which will be important for designing superconducting device robust to temperature cycles using zero-thermal-expansion superconductors.

Highlights:

  • Uniaxial negative thermal expansion was observed in V3V_{3}S-type IrZr3_{3}.

  • IrZr3_{3} is a superconductor with a transition temperature of 2.3 K.

  • Uniaxial negative thermal expansion emerges in various transition-metal zirconides.

Introduction

Materials with characteristics of negative thermal expansion (NTE) or zero thermal expansion (ZTE) [1, 2, 3, 4, 5] have been utilized in various devices in which ultra-precision and small (or zero) displacements of position of components are required. Since ZTE compounds are rare as compared to NTE compounds, ZTE function is normally achieved by making composite materials of NTE and positive thermal expansion (PTE) compounds. Our study focuses on superconductors with anomalous axis thermal expansion. Thermal cycle has been a critical problem for superconducting materials and devices [6, 7, 8]. As well known, superconducting devices are used at very low temperatures and the fabrication process is basically done at higher temperatures. Hence, the affection of the thermal cycle to the device performance cannot be ignored. In addition, superconducting characteristics (superconducting states and performance) are generally sensitive to the presence of impurity and the stress to the grains. Therefore, discovery of ZTE superconductor is expected to improve the robustness of superconducting devices to thermal cycle. One of the ways to achieve ZTE in superconductor is the design of zero volume expansion in superconductors with uniaxial NTE. For example, in a tetragonal system, the NTE along the cc-axis can compensate the PTE along the aa-axis, which would result in the ZTE of the volume.

Recently, we reported uniaxial NTE in CoZr2_2 and alloyed TrTrZr2_2 (TrTr: transition metal) with a tetragonal CuAl2_2-type structure (space group: I4/mcmI4/mcm, #140) (see Figure 1a) [9]. The observed NTE along the cc-axis is relatively large among superconductors exhibiting uniaxial NTE [10, 11, 12, 13, 14, 15, 16]; the cc-axis thermal expansion constant for CoZr2_2 is αc=−28\alpha_c = -28 μK−1^{-1} [9]. Notably, volume ZTE has been seen in limited temperature range in CoZr2_2 [9]. In TrTrZr2_2, the thermal expansion is controllable by tuning c/ac/a ration of the tetragonal unit cell [17, 18]. More recently, we reported the observation of uniaxial NTE in CoZr3_3 with an orthorhombic Re3_3B-type structure (space group: CmcmCmcm, #63) (see Figure 1b) [19]. Since uniaxial NTE has been observed in two different structural types, the uniaxial NTE in zirconides would be common characteristics. Therefore, to find out potential structural types where uniaxial NTE could be observed, we explored NTE in Ir-Zr compounds. Here, we show the uniaxial NTE in tetragonal V3_3S-type (space group: II-42mm, #121) IrZr3_3. Although the observed NET in IrZr3_3 is weaker than CoZr2_2, the observation of uniaxial NTE in IrZr3_3 provides us with a useful strategy to design new NET superconductors.

Schematic images of crystal structure of (a) CoZr2, (b) CoZr3, and (c) IrZr3

Figure 1. Schematic images of crystal structure of (a) CoZr2_2, (b) CoZr3_3, and (c) IrZr3_3. The squares indicate unit cells. NTE explains the direction of uniaxial negative thermal expansion.

Material and methods

Polycrystalline samples (sample #1 and #2) of IrZr3_3 were prepared by arc melting. Ir powder (99.9%, Kojundo Kagaku) and Zr plates (99.2%, Nilaco) were used for the syntheses. For sample #1, stoichiometric amount of IrZr3_3 were melted. For sample #2, 1%-Zr-excess composition (IrZr3.03_{3.03}) was used to compensate evaporation of Zr, but the quality of the obtained samples was comparable. Arc melting was performed in an Ar-filled chamber with two torches, and the samples were melted four times after turning over the sample. High-temperature X-ray diffraction (HTXRD) was performed on a Miniflex600 diffractometer (RIGAKU) equipped with a temperature-control device BTS-500 up to 573 K in vacuum. X-ray with Cu-Kα\alpha radiation was used, and the diffraction data were collected using a semiconductor analyzer D/tex-Ultra (RIGAKU). Rietveld refinement was performed using RIETAN-FP [20], and the schematic images of crystal structure were drawn by VESTA [21]. Superconducting transition temperature (TcT_{\mathrm{c}}) was measured by magnetic susceptibility on a superconducting quantum interference device (SQUID) magnetometer MPMS-3 (Quantum Design).

Results and discussion

As mentioned above, uniaxial NTE has been observed in CuAl2_2-type CoZr2_2 and TrZr2_2 (Figure 1a) [9] and Re3_3B-type CoZr3_3 (Figure 1b) [19]. Here, we report on the observation of uniaxial NTE in V3_3S-type IrZr3_3 (Figure 1c). Figure 2 shows the temperature dependence of magnetic susceptibility after zero-field cooling (ZFC) and field cooling (FC). A large negative susceptibility signals were observed below Tc=2.3T_{\mathrm{c}} = 2.3 K, which is consistent with previous works [22, 23].

Temperature dependence of susceptibility for IrZr3 (sample #1)

Figure 2. Temperature dependence of susceptibility for IrZr3_3 (sample #1). Both FC and ZFC data are shown.

Figure 3 shows the powder XRD pattern and the Rietveld refinement result for sample #1. Although small unknown peaks were included, almost all the peaks were explained with IrZr3_3 (97%) and IrZr2_2 (3%) with a cubic structure (space group: #227). Since the higher-angle peaks were well refined, the assumed structural model of V3_3S-type IrZr3_3 is reasonable. See Table 1 for the refinement results. The refinement was performed with constant value of isotropic displacement parameter Uiso=0.127U_{\mathrm{iso}} = 0.127 Å2^2 for both sites.

SampleIrZr3_3 (sample #1)
Space groupII-42mm (#121)
Temperature (K)296
aa (\AA)10.7875(3)
cc (\AA)5.6573(2)
VV (\AA3^{3})658.35(4)
xx (Ir)0.2908(3)
xx (Zr1)0.0907(4)
xx (Zr2)0.2932(3)
xx (Zr3)0.3515(3)
RwpR_{\mathrm{wp}}9.4%
Ideal density (g/cm3^{3})9.400805

Table 1. Structural parameter of IrZr3_3 determined from Rietveld refinement (Figure 1). Atomic coordinates are Ir: (xx, 0, 0), Zr1: (xx, xx, 0.25), Zr2: (xx, xx, 0.25), and Zr3: (xx, 0, 0.5).

Powder XRD pattern and Rietveld refinement result for IrZr₃ (sample #1)

Figure 3. Powder XRD pattern and Rietveld refinement result for IrZr₃ (sample #1). The peaks with asterisk were unidentified. Numbers in the figure are Miller indices.

To evaluate temperature evolutions of lattice parameters, HTXRD were performed on two samples (#1 and #2). Figure 4 displays HTXRD patterns for sample #1 (see Supplementary material for HTXRD data for sample #2). To see the shifts of 00ll and hh00 peaks, the 002 and 400 peaks were highlighted in Figure 4b. The 400 peak continuously shifts to lower angles with increasing temperature, which indicates PTE along the aa-axis. In contrast, the 002 peak slightly shifts to higher angles with increasing temperature, which suggests NTE along the cc-axis. Figure 5 shows the temperature dependences of the obtained lattice parameters of aa, cc, and VV. For both samples, PTE along the aa-axis and NTE along the cc-axis have been confirmed from the shift of lattice parameters. Two different samples exhibited comparable behavior of uniaxial NTE in IrZr3_3. The estimated αc\alpha_c for IrZr3_3 is -4 μK−1^{-1}, which is clearly weaker than that observed in CoZr2_2, and it seems to be saturated above 500 K. The results, however, propose that uniaxial NTE in Tr-Zr binary systems is not unique property of Co-Zr systems (CuAl2_2-type CoZr2_2 and Re3_3B-type CoZr3_3), and Tr-Zr binary systems with various structural types and wide-range of transition metals are potential materials for uniaxial NTE or anomalous axis thermal expansion. Since common origins are expected to present in various Tr-Zr binary compounds and related zirconides with uniaxial NTE, further investigations on crystal structure, electronic structure, and phonon characteristics of Tr-Zr systems are needed.

HTXRD patterns for IrZr₃ (sample #1) and zoomed patterns near the 002 and 400 peaks

Figure 4. (a) HTXRD patterns for IrZr₃ (sample #1). (b) Zoomed patterns near the 002 and 400 peaks.

Temperature dependences of lattice parameters for IrZr₃ samples

Figure 5. Temperature dependences of lattice parameters of (a) aa, (b) cc, and (c) VV for the IrZr3_3 samples (#1 and #2).

Conclusions

We synthesized polycrystalline samples of IrZr3_3 with a V3_3S-type tetragonal structure and investigated the superconducting and structural properties. Uniaxial NTE was observed along the cc-axis in IrZr3_3: with increasing temperature, the lattice parameters of aa and VV of IrZr3_3 increase, but the lattice parameter of cc decreases. From the susceptibility measurements, superconductivity with a TcT_{\mathrm{c}} of 2.3 K was confirmed in IrZr3_3. The present result suggests that uniaxial NTE and related anomalous axis thermal expansion occur in various transition-metal zirconides and encourages further material development, characterization, and investigations on mechanisms in uniaxial NTE in TrTr-Zr systems.

Acknowledgements

The author thanks O. Miura, H. Arima, A. Yamashita, and K. Mizuguchi for supports in experiments and discussion. This work was partly supported by the Tokyo Government Advanced Research (No.: H31-1), JSPS-KAKENHI (Nos.: 21H00151, 21K18834), and JST-ERATO (No.: JPMJER2201).

Data statement

The raw data reported in this paper can be provided by a reasonable request to the corresponding author.

Supplementary material

HTXRD patterns for IrZr$_3$ (Sample #2), showing intensity versus $2\theta$ for measurements from 302 K to 573 K

Figure S1. HTXRD patterns for IrZr3_3 (sample #2).

References

  1. [1]1) K. Takenaka, Sci. Technol. Adv. Mater. 13, 013001 (2012).
  2. [2]2) G. D. Barrera, J. A. O. Bruno, T. H. K. Barron, N. L. Allan, J. Phys.: Condens. Matter 17, R217 (2005).
  3. [3]3) J. Chen, L. Hu, J. Deng, X. Xing, Chem. Soc. Rev. 44, 3522 (2015).
  4. [4]4) T. A. Mary, J. S. O. Evans, T. Vogt, A. W. Sleight, Science 272, 90 (1996).
  5. [5]5) K. Takenaka, Y. Okamoto, T. Shinoda, N. Katayama, Y. Sakai, Nat. Commun. 8, 14102 (2016).
  6. [6]6) J. E. Zimmerman, Paul Thiene, J. T. Harding, J. Appl. Phys. 41, 1572 (1970).
  7. [7]7) K. Watanabe et al., Cryogenics 34, 639 (1994).
  8. [8]8) N. Sakai, S.J. Seo, K. Inoue, T. Miyamoto, M. Murakami, Physica C 335, 107 (2000).
  9. [9]9) Y. Mizuguchi, Md. R. Kasem, Y. Ikeda, J. Phys. Soc. Jpn. 91, 103601 (2022).
  10. [10]10) S. L. Bud’ko, N. Ni, S. Nandi, G. M. Schmiedeshoff, P. C. Canfield, Phys. Rev. B 79, 054525 (2009).
  11. [11]11) S. A. J. Kimber, D. N. Argyriou, F. Yokaichiya, K. Habicht, S. Gerischer, T. Hansen, T. Chatterji, R. Klingeler, C. Hess, G. Behr, A. Kondrat, B. Büchner, Phys. Rev. B 78, 140503 (2008).
  12. [12]S. V. Pryanichnikov, S. G. Titova, G. A. Kalyuzhnaya, Yu. I. Gorina, P. A. Slepukhin, J. Exp. Theor. Phys. 107, 69 (2008).
  13. [13]H. Fujishita, Y. Hayashi, M. Saito, H. Unno, H. Kaneko, H. Okamoto, M. Ohashi, Y. Kobayashi, M. Sato, Eur. Phys. J. B 85, 52 (2012).
  14. [14]M. S. da Luz, J. J. Neumeier, R. K. Bollinger, A. S. Sefat, M. A. McGuire, R. Jin, B. C. Sales, D. Mandrus, Phys. Rev. B 79, 214505 (2009).
  15. [15]S. L. Bud’ko, N. Ni, P. C. Canfield, Philos. Mag. 90, 1219 (2010).
  16. [16]J. J. Neumeier, T. Tomita, M. Debessai, J. S. Schilling, P. W. Barnes, D. G. Hinks, J. D. Jorgensen, Phys. Rev. B 72, 220505 (2005).
  17. [17]H. Arima, Md. R. Kasem, arXiv:2210.10367.DOI
  18. [18]Y. Watanabe, H. Arima, H. Usui, Y. Mizuguchi, arXiv:2211.00958.DOI
  19. [19]H. Arima, T. Inui, A. Yamashita, A. Miura, H. Itou, C. Moriyoshi, H. Fujihisa, Y. Mizuguchi, arXiv:2211.13947.DOI
  20. [20]F. Izumi and K. Momma, Solid State Phenom. 130, 15 (2007).
  21. [21]K. Momma and F. Izumi, J. Appl. Crystallogr. 41, 653 (2008).
  22. [22]T. Shang, S. K. Ghosh, J. Z. Zhao, L.-J. Chang, C. Baines, M. K. Lee, D. J. Gawryluk, M. Shi, M. Medarde, J. Quintanilla, T. Shiroka, Phys. Rev. B 102, 020503 (2020).
  23. [23]S. L. McCarthy, J. Low Temp. Phys. 4, 489 (1971).

Paper details

vlnc:W_yvayc7h3
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents