betaFeedback

WorksPhysics and Astronomy

Multiple Linear Regression-Enhanced RGB-based Luminescence Thermometry for High-sensitivity Thermal Readout

Abstract

The practical implementation of phosphors for luminescence-based thermal sensing and imaging requires simple, user-friendly approaches that enable convenient and sensitive temperature readout. To the best of our knowledge, this is the first demonstration of combining RGB-based thermal imaging using a conventional digital camera with multiple linear regression (MLR) to achieve straightforward and highly sensitive temperature determination and spatially resolved thermal imaging. Importantly, the implementation of the MLR approach enhances the relative sensitivity by more than 3-fold, compared with conventional analysis based solely on the G/R or B/R intensity ratios. The application of Ca3Al2O6:Mn2+-Ce3+ as a luminescent temperature probe, in which the intensity ratio between the Ce3+ and Mn2+ emission bands exhibits a pronounced temperature dependence, enables temperature readout through several complementary approaches. These include conventional luminescence intensity ratio thermometry (SR = 1.46% K-1), analysis of the CIE 1931 chromaticity coordinates (SRx = 0.45% K-1 and SRy = 0.14% K-1), as well as RGB-based thermal sensing and imaging using a digital camera. This multimodal optical response, together with the accessibility of camera-based readout and the substantial sensitivity enhancement enabled by MLR, establishes a practical strategy for spatially resolved luminescence thermometry.

*corresponding author: [email protected] temperature probe, in which the intensity ratio between the Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} emission bands exhibits a pronounced temperature dependence, enables temperature readout through several complementary approaches. These include conventional luminescence intensity ratio thermometry (SR=1.46%S_{\mathrm{R}} = 1.46\% K−1\mathrm{K}^{-1}), analysis of the CIE 1931 chromaticity coordinates (SRx=0.45%S_{\mathrm{R}x} = 0.45\% K−1\mathrm{K}^{-1} and SRy=0.14%S_{\mathrm{R}y} = 0.14\% K−1\mathrm{K}^{-1}), as well as RGB-based thermal sensing and imaging using a digital camera. This multimodal optical response, together with the accessibility of camera-based readout and the substantial sensitivity enhancement enabled by MLR, establishes a practical strategy for spatially resolved luminescence thermometry.

Introduction

The use of thermally induced changes in the spectroscopic properties of phosphors for temperature readout has been well established and applied in numerous fields for many years [1, 2, 3, 4, 5, 6]. In the vast majority of cases, such luminescent thermometers rely on either a ratiometric approach or the kinetics of luminescence [1, 2, 3, 4, 5, 6]. Although these are not the only parameters exhibiting thermal sensitivity, their principal advantage lies in their low or negligible sensitivity (under certain specific conditions) to changes in the local environment and measurement conditions [7]. Both approaches provide reliable and accurate remote temperature readout. However, in each case, temperature measurement requires the use of complex and often expensive detection systems, such as I) emission spectrometers coupled to the cooled CCD or CMOS cameras; or II) time-resolved spectroscopy setups composed of pulsed lasers and photomultipliers. The cost of such systems, their lack of portability, and the complexity of their operation can limit the accessibility of luminescence thermometry for widespread use. Moreover, these approaches typically allow only for point-wise temperature measurement, meaning that thermal imaging of a surface coated with a luminescent thermometer requires point-by-point acquisition of luminescence spectra or luminescence kinetics [4, 8, 9, 10, 11]. This is not only time-consuming but, in the case of rapidly changing thermal gradients, also results in the loss of valuable information regarding the spatial distribution of thermal variations.

To address these limitations, an alternative approach to thermal imaging has recently been proposed, employing a conventional digital camera as the detector[12, 13, 14, 15, 16, 17]. In its original implementation, this approach enables temperature readout by capturing two luminescence images using appropriate external optical filters, whose spectral characteristics match the shape of the phosphor's luminescence spectrum[12, 13, 14, 18]. This solution allows for two-dimensional imaging of thermal changes; however, the procedure of optical filter exchange introduces additional practical difficulties and limits the dynamics of the thermal changes that could be recorded. Consequently, a considerably simpler solution was recently proposed, based on the intensity ratio of luminescence maps recorded in the RGB channels of a digital camera[15, 16, 17, 19, 20, 21, 22]. These signals are automatically captured by any conventional camera, and their ratio can serve as a temperature-dependent parameter. The effectiveness and simplicity of this approach have been demonstrated in previous studies.

When considering a suitable phosphor for this type of thermal imaging, it is essential to ensure that the emission bands of the optically active dopants are selectively located within the spectral ranges corresponding to the sensitivity ranges of the individual RGB channels. In this context, systems co-doped with Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} ions appear particularly promising, as Ce3+\mathrm{Ce}^{3+} is responsible for blue luminescence[23, 24, 25], while Mn2+\mathrm{Mn}^{2+} ions located in an octahedral crystallographic environment give rise to intense red emission. Notably, what distinguishes Mn2+\mathrm{Mn}^{2+} ions from other red-emitting activators is that an increase in temperature induces thermalization of higher-lying vibronic components of the excited state, resulting in a blue shift of the emission band[26, 27, 28, 29, 30]. This effect is particularly significant, as it enables the recording of thermally activated luminescence in the green, G channel, which initially (at low temperatures) detects no signal. This, in turn, allows for high sensitivity of the measurement.

In this work, we demonstrate the possibility of enhancing the relative sensitivity of such thermal imaging through the application of multiple linear regression (MLR) algorithms[31, 32, 33, 34, 35] (Figure 1). To the best of our knowledge, this constitutes the first demonstration of this approach in filter-free thermal imaging, and as will be shown, it enables a significant increase in thermal sensitivity, which is crucial for reliable thermal imaging. The advantage of MLR in this context lies in its numerical simplicity, which eliminates the need for complex computational algorithms to perform the measurement. To demonstrate this approach, studies were carried out on Ca3Al2O6:Ce3+, Mn2+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}:\mathrm{Ce}^{3+},\ \mathrm{Mn}^{2+} as a function of dopant ion concentration and temperature. Additionally, as it will be shown Ca3Al2O6:Ce3+, Mn2+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}:\mathrm{Ce}^{3+},\ \mathrm{Mn}^{2+} offers other mode of temperature readout confirming its potential for multimodal readout.

Schematic representation of the concept proposed in this work

Figure 1. Schematic representation of the concept proposed in this work. Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} co-doped with Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} is employed as a luminescent thermometer exhibiting a temperature-dependent change in emission color resulting from the different thermal responses of Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} luminescence. The emission can be directly recorded using a conventional digital camera, enabling rapid and cost-effective temperature readout based on the temperature-dependent response of the RGB channels. Implementation of multiple linear regression (MLR) analysis using the RGB signals significantly improves the thermometric performance, providing an

approximately threefold enhancement of the relative thermal sensitivity compared with the conventional RGB-based approach. The distinct thermal evolution of the Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} emission contributions enables multimodal temperature sensing using four complementary readout strategies: (1) spectroscopic ratiometric thermometry, (2) chromaticity-coordinate analysis, (3) RGB-based thermometry, and (4) MLR-assisted RGB thermometry.

RESULTS

Structural and morphological characterization

The powder XRD patterns of the Ca3Al2O6:Mn2+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}:\mathrm{Mn}^{2+}-Ce3+\mathrm{Ce}^{3+} phosphors, together with the reference data of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} (ICSD 1841), presented in Figure 2a confirm that pure cubic phase of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} with the Pa-3Pa\text{-}3 space group was obtained for all investigated samples with varying Mn2+\mathrm{Mn}^{2+} concentrations, both in the Ce3+/Mn2+\mathrm{Ce}^{3+}/\mathrm{Mn}^{2+} co-doped samples and in the samples doped exclusively with Ce3+\mathrm{Ce}^{3+} (Figure S1)[36, 37, 38, 39, 40, 41, 42, 43]. There are six distinct crystallographic sites occupied by Ca2+\mathrm{Ca}^{2+} ions in Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}, as shown in Figure 2b. The Ca(1), Ca(2) and Ca(3) sites are each coordinated by six oxygen atoms, forming octahedral coordination environments. In contrast, the Ca(4), Ca(5), and Ca(6) sites are coordinated by nine, eight and seven oxygen atoms, respectively[44, 45]. The numbers of Ca(1)-Ca(6) sites per unit cell are 4, 4, 8, 8, 24 and 24, respectively. Owing to its larger coordination number, the Ca(4) site is expected to be the most favorable site for Ce3+\mathrm{Ce}^{3+} incorporation. However, the molar ratio of the Ca(4), Ca(5), and Ca(6) sites is 1:3:3 within the Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} unit cell, suggesting that the Ce3+\mathrm{Ce}^{3+} ions have a greater probability of occupying the more abundant Ca(5) and Ca(6) sites.

Powder XRD patterns, crystal structure, Raman spectrum, SEM image and elemental distributions, excitation and emission spectra, and configurational coordination diagram

Figure 2. Powder XRD patterns of Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:x% Mn2+\mathrm{Mn}^{2+}-5% Ce3+\mathrm{Ce}^{3+} with different Mn2+\mathrm{Mn}^{2+} concentrations– a); Visualization of the Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6 structure – b); Raman spectrum measured at 83 K – c) and representative SEM image and elemental distributions of Ca, Al, O, Mn and Ce – d) for Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:5% Mn2+\mathrm{Mn}^{2+}-5% Ce3+\mathrm{Ce}^{3+}; excitation and emission spectra of Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:0.1%Ce3+\mathrm{Ce}^{3+} measured at 93 K at different emission and excitation wavelengths – e); simplified configurational coordination diagram of Ce3+\mathrm{Ce}^{3+} ions localized at different crystallographic sites– f).

The Raman spectrum recorded at 83 K for the sample co-doped with 5% Mn2+\mathrm{Mn}^{2+} and 5% Ce3+\mathrm{Ce}^{3+} exhibits four main Raman modes in the range of 300-950 cm−1\mathrm{cm}^{-1} (Figure 2c). The bands below 400 cm−1\mathrm{cm}^{-1} are mainly attributed to lattice vibrations and external modes involving Ca-O coordination environments. In contrast, the three intense bands centered at approximately 530, 640 and 780 cm−1\mathrm{cm}^{-1} are associated with internal vibrations of the AlO45−\mathrm{AlO}_{4}^{5-} units. The band at approximately 530 cm−1\mathrm{cm}^{-1} can be assigned to vibrations involving Al-O-Al linkages, whereas the feature near 640 cm−1\mathrm{cm}^{-1} is related to Al-O vibrations of mixed stretching and bending character. The high-frequency band around 780 cm−1\mathrm{cm}^{-1} is mainly attributed to symmetric Al-O stretching vibrations. The observed splitting and broadening of the Raman bands can be related to the structural complexity of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}, which contains six crystallographically inequivalent Ca sites and two distinct Al sites, resulting in a distribution of metal-oxygen bond lengths and local coordination environments.

SEM images taken for the same sample (Figure 2d) reveal that the material studied consists of irregularly shaped microcrystals characteristic of products obtained by high-temperature solid-state synthesis, without a well-defined or uniform morphology. Furthermore, EDS elemental maps of Ca, Al, O, Mn and Ce confirm a homogeneous spatial distribution of all constituent elements throughout the analyzed region.

To develop a visual luminescent thermometer, it is necessary to obtain distinct luminescence contributions in different spectral ranges. Ce3+\mathrm{Ce}^{3+} ions are among the most well-known luminescent activators exhibiting intense emission in the blue spectral region. The analysis of the spectroscopic properties of Ca3Al2O6 ⁣:Ce3+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}\!:\mathrm{Ce}^{3+} directly reveals the presence of more than one crystallographic site occupied by Ce3+\mathrm{Ce}^{3+} ions. As shown in Figure 2e, both the excitation and emission spectra strongly depend on the local coordination environment of the Ce3+\mathrm{Ce}^{3+} ions. Under excitation at 460 nm, the material studied exhibits a broad emission band centered at 562 nm, corresponding to the allowed Ce3+\mathrm{Ce}^{3+} 5d1→4f15d^{1} \rightarrow4f^{1} electronic transition [46, 47, 48, 49]. A distinct shoulder appears on the longer wavelength side of the asymmetric emission spectrum. As shown in Figure S2, deconvolution of their emission spectra into Gaussian bands reveals that the spectrum consists of two emission components, which are attributed to the transitions from the 5d5d excited state to the two ground levels of Ce3+\mathrm{Ce}^{3+}, i.e. 2F7/2^{2}\mathrm{F}_{7/2} and 2F5/2^{2}\mathrm{F}_{5/2}. The energy separation between these peaks (centered at 15,527 cm−1\mathrm{cm}^{-1} and 17,979 cm−1\mathrm{cm}^{-1}) reaches approximately 2,450 cm−1\mathrm{cm}^{-1}. This value is close to the spin-orbit splitting between the 2F7/2^{2}\mathrm{F}_{7/2} and 2F5/2^{2}\mathrm{F}_{5/2} states usually observed for Ce3+\mathrm{Ce}^{3+} doped phosphors (approximately 2,000 cm−1\mathrm{cm}^{-1})[50], further confirming the assignment of the two emission bands. When monitored at 562 nm, the excitation spectrum exhibits a broad band centered at approximately 460 nm, along with two additional bands at approximately 305 nm and 360 nm. These bands are attributed to the 4f1→5d14f^{1} \rightarrow5d^{1} electronic transitions of Ce3+\mathrm{Ce}^{3+}. Upon excitation at 305 nm, the emission spectrum displays several broad emission bands. Gaussian deconvolution reveals that the spectrum consists of four emission components centered at approximately 21,021 cm−1\mathrm{cm}^{-1}, 23,184 cm−1\mathrm{cm}^{-1}, 24,267 cm−1\mathrm{cm}^{-1}, and 26,061 cm−1\mathrm{cm}^{-1}, respectively. These bands can be readily paired, and the corresponding energy differences between them are again, as expected close to the spin-orbit splitting between the 2F7/2{}^{2}F_{7/2} and 2F5/2{}^{2}F_{5/2} state levels of Ce3+\mathrm{Ce}^{3+} (2163 cm−1\mathrm{cm}^{-1} between 21021 cm−1\mathrm{cm}^{-1} and 23184 cm−1\mathrm{cm}^{-1}), and 1794 cm−1\mathrm{cm}^{-1} (between 24267 cm−1\mathrm{cm}^{-1} and 26061 cm−1\mathrm{cm}^{-1}). Furthermore, when monitored at 360 nm, the emission spectrum exhibits a broad asymmetric band centered at approximately 505 nm. Analogously in this case Gaussian deconvolution of emission spectra reveals the presence of bands at 19889 cm−1\mathrm{cm}^{-1}, 22672 cm−1\mathrm{cm}^{-1}, 23644 cm−1\mathrm{cm}^{-1}, and 25045 cm−1\mathrm{cm}^{-1}, respectively. These luminescence properties suggest that Ce3+\mathrm{Ce}^{3+} ions occupy multiple crystallographically distinct sites in Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}, giving rise to different optical response. The crystal structure of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} contains six different crystalline sites of Ca2+\mathrm{Ca}^{2+} ions, all of which are coordinated exclusively by oxygen atoms. Among them, Ca(1), Ca(2), and Ca(3) are each six-coordinated, forming octahedral environments, whereas Ca(4), Ca(5), and Ca(6) are coordinated by nine, eight, and seven oxygen atoms, respectively. Furthermore, the numbers of Ca(1), Ca(2), Ca(3), Ca(4), Ca(5), and Ca(6) sites per unit cell are 4, 4, 8, 8, 24, and 24, respectively. Therefore, Ce3+\mathrm{Ce}^{3+} ions are more likely to occupy Ca(5) and Ca(6) sites. This preferential occupation is consistent with the observed multiple emission bands and excitation-dependent luminescence behavior. According to the report of Van Uitert, the positions of the lower d-band edge for Ce3+\mathrm{Ce}^{3+} ion were calculated using the following empirical formula[51]:

Equation not extracted
E=Q[1−(V4)1V10−n ea80](1)E=Q\left[1-\left(\frac{V}{4}\right)^{\frac{1}{V}}10^{-\frac{n\,ea}{80}}\right] \tag*{(1)}

where the position in energy (QQ) is 50,000 cm−1^{-1} for the lower d-band edge for free Ce3+^{3+} ion, the valence (VV) is +3 for the activator Ce3+^{3+}, nn is the coordination number of Ce3+^{3+}, the electron affinity (eaea) of the atoms that form anions is 1.60, and rr is the radius of the host cation replaced by the Ce3+^{3+} ion. The values of rr for the MO9_9, MO8_8, and MO7_7 coordination polyhedral are determined by subtracting the ionic radius of O2−^{2-} from the corresponding average M–O bond lengths. Accordingly, the EE values of Ce3+^{3+} occupying the Ca(4), Ca(5), and Ca(6) sites are calculated to be 23,427 cm−1^{-1}, 21,072 cm−1^{-1}, and 18,397 cm−1^{-1}, respectively. These calculated values indicate that the emission bands observed under 305 nm and 360 nm excitation are attributable to Ce3+^{3+} ions occupying the Ca(4) and Ca(5) sites, respectively. In contrast, the emission observed under 460 nm excitation is assigned to Ce3+^{3+} occupying the Ca(6) site (Figure 2f). The emission spectral profiles corresponding to the Ca(4) and Ca(5) sites exhibit concentration-dependent variations with increasing Ce3+^{3+} concentration (Figure S3). Under 305 nm excitation, the emission from the Ca(4) site dominates at low Ce3+^{3+} concentrations, whereas the emission profile is reversed at high concentrations, with the Ca(5) site becoming the dominant emission center. Conversely, under 360 nm excitation, the emission band is dominated by the Ca(5) site at low concentration, however, with increasing Ce3+^{3+} concentration, the Ca(4) site becomes the predominant emission center. This phenomenon might be related to variations in the emission probabilities under different excitation wavelengths. Several factors could contribute to this behavior, including the splitting of energy levels, the degree of distortion of the Ca2+^{2+} sites, the Ce3+^{3+}–O2−^{2-} bond lengths, differences in site occupancy, and the distances between Ce3+^{3+} ions at different Ce3+^{3+} concentrations. In contrast, the emission spectra recorded under 460 nm excitation show no noticeable changes with varying Ce3+^{3+} concentrations (Figure S3).

Luminescent properties of Ca3Al2O6 ⁣:Ce3+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}\!:\mathrm{Ce}^{3+} and Ca3Al2O6 ⁣:Ce3+,Mn2+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}\!:\mathrm{Ce}^{3+},\mathrm{Mn}^{2+}

To achieve a temperature-dependent variation in the emission color of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}, which is essential from the perspective of visual luminescence thermometry, Ca3Al2O6 ⁣:Ce3+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}\!:\mathrm{Ce}^{3+} was codoped with Mn2+\mathrm{Mn}^{2+} ions. This approach was motivated by the fact that Mn2+\mathrm{Mn}^{2+} ions located in an octahedral coordination environment exhibit intense red emission associated with the 4T1(4G)→6A1(6S){}^{4}\mathrm{T}_{1}({}^{4}\mathrm{G}) \to{}^{6}\mathrm{A}_{1}({}^{6}\mathrm{S}) electronic transition[52]. According to the Tanabe-Sugano diagram for transition-metal ions with a 3d53d^{5} electronic configuration, the energy of the 4T1{}^{4}\mathrm{T}_{1} excited state is strongly dependent on the crystal field strength experienced by Mn2+\mathrm{Mn}^{2+} ions (Figure 3a)[26, 27, 52, 53, 54, 55]. In Ca3Al2O6 ⁣:Ce3+,Mn2+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}\!:\mathrm{Ce}^{3+},\mathrm{Mn}^{2+}, the 4T1(4G)→6A1(6S){}^{4}\mathrm{T}_{1}({}^{4}\mathrm{G}) \to{}^{6}\mathrm{A}_{1}({}^{6}\mathrm{S}) transition gives rise to a broad emission band centered at around 650 nm, providing a spectrally well-separated emission component with respect to the Ce3+\mathrm{Ce}^{3+} luminescence.

Simplified configurational coordination diagram, excitation and emission spectra, normalized emission spectra, CIE1931 chromatic coordinates and luminescence photographs, and Mn²⁺ to Ce³⁺ emission intensity ratio

Figure 3. Simplified configurational coordination diagram of Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} ions – a); excitation and emission spectra of Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:0.2% Mn2+\mathrm{Mn}^{2+} (blue and purple) and Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:5%Ce3+\mathrm{Ce}^{3+} (orange) measured at 93 K at different emission and excitation wavelengths – b); normalized emission spectra– c), CIE1931 chromatic coordinates and corresponding photos of their luminescence -d) and the influence of Mn2+\mathrm{Mn}^{2+} ions concentration on the Mn2+\mathrm{Mn}^{2+} to Ce3+\mathrm{Ce}^{3+} emission intensity ratio for Ca19Zn2(PO4)14\mathrm{Ca}_{19}\mathrm{Zn}_2(\mathrm{PO}_4)_{14}:Mn2+\mathrm{Mn}^{2+}, 5%Ce3+\mathrm{Ce}^{3+} with different Mn2+\mathrm{Mn}^{2+} ions concentration measured at 93 K – e).

The excitation and emission spectra of the 0.2% Mn2+\mathrm{Mn}^{2+}, 5% Ce3+\mathrm{Ce}^{3+} co-doped phosphor (blue and purple curves) and the 5% Ce3+\mathrm{Ce}^{3+} phosphor (orange curves), recorded under different excitation conditions, provide important insight into the underlying excitation and energy-transfer processes (Figure 3b). Upon excitation at 305 nm, the co-doped sample exhibits the characteristic emission bands of Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+}, centered at approximately 485 nm and 650 nm, respectively. These bands are assigned to the Ce3+\mathrm{Ce}^{3+} 5d1→4f1{}^{5}d^{1} \to{}^{4}f^{1} and Mn2+\mathrm{Mn}^{2+} 4T1(4G)→6A1(6S){}^{4}\mathrm{T}_{1}({}^{4}\mathrm{G}) \to{}^{6}\mathrm{A}_{1}({}^{6}\mathrm{S}) electronic transitions, respectively. The excitation spectrum monitored at the Ce3+\mathrm{Ce}^{3+} emission wavelength of 485 nm consists of several bands in the 250-400 nm spectral range, which can be assigned to the Ce3+\mathrm{Ce}^{3+} 4f1→5d{}^{4}f^{1} \to{}^{5}d transitions. In contrast, the excitation spectrum monitored at the Mn2+\mathrm{Mn}^{2+} emission wavelength of 650 nm contains not only the characteristic Mn2+\mathrm{Mn}^{2+} 6A1(6S)→4T2(4G){}^{6}\mathrm{A}_{1}({}^{6}\mathrm{S}) \to{}^{4}\mathrm{T}_{2}({}^{4}\mathrm{G}) excitation band but also the Ce3+\mathrm{Ce}^{3+} 4f1→5d{}^{4}f^{1} \to{}^{5}d excitation bands. Importantly, the spectral positions of these bands coincide with those observed in the excitation spectrum monitored at the Ce3+\mathrm{Ce}^{3+} emission. The presence of the Ce3+\mathrm{Ce}^{3+} excitation features in the excitation spectrum of Mn2+\mathrm{Mn}^{2+} provides direct evidence for Ce3+→Mn2+\mathrm{Ce}^{3+} \to\mathrm{Mn}^{2+} energy transfer.

The comparison of the emission spectra of Ca3Al2O6:Ce3+:Mn2+\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:\mathrm{Ce}^{3+}:\mathrm{Mn}^{2+} recorded at 93 K for phosphors with Mn2+\mathrm{Mn}^{2+} concentrations ranging from 0.05% to 5% indicate that at low Mn2+\mathrm{Mn}^{2+} concentrations, the emission spectra are dominated by the Ce3+\mathrm{Ce}^{3+} luminescence (Figure 3c). However, increasing the Mn2+\mathrm{Mn}^{2+} concentration results in a pronounced enhancement of the Mn2+\mathrm{Mn}^{2+} emission relative to the Ce3+\mathrm{Ce}^{3+}. This effect can be explained by the co-existence of two mechanism: (i) growing number of Mn2+\mathrm{Mn}^{2+} emitting centers and (ii) more efficient Ce3+→Mn2+\mathrm{Ce}^{3+}\to\mathrm{Mn}^{2+} energy transfer. The substantial modification of the relative contributions of Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} luminescence results in a pronounced change in the overall emission color, as illustrated in Figure 3d. This effect originates from the large spectral separation between the blue Ce3+\mathrm{Ce}^{3+} and red Mn2+\mathrm{Mn}^{2+} emission bands. Consequently, at low Mn2+\mathrm{Mn}^{2+} concentrations the overall emission is dominated by the blue Ce3+\mathrm{Ce}^{3+} component, whereas increasing the Mn2+\mathrm{Mn}^{2+} concentration progressively enhances the red contribution and shifts the resulting emission color toward the red spectral region. Such concentration-controlled tuning of the relative Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} emission contributions provides a suitable basis for generating a pronounced temperature-dependent color response and, consequently, for the development of visual luminescence thermometry. This evolution is quantitatively reflected by the Mn2+\mathrm{Mn}^{2+}-to-Ce3+\mathrm{Ce}^{3+} integrated emission intensity ratio, which increases systematically with increasing Mn2+\mathrm{Mn}^{2+} concentration (Figure 3e). Specifically, increasing the Mn2+\mathrm{Mn}^{2+} concentration from 0.05% to 5% enhances the Mn2+\mathrm{Mn}^{2+}-to-Ce3+\mathrm{Ce}^{3+} emission intensity ratio from 0.16 to 6.4, corresponding to a 40-fold increase.

Thermometric performance of Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:Ce3+\mathrm{Ce}^{3+}, Mn2+\mathrm{Mn}^{2+}

To evaluate the potential of the Ca3Al2O6\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:Mn2+\mathrm{Mn}^{2+}-Ce3+\mathrm{Ce}^{3+} material for optical thermometry, its temperature-dependent photoluminescence properties were systematically investigated over the TT-range from 93 to 573 K. As clearly shown in Figure 4a (Figure S4, S5), increasing the temperature leads to a systematic decrease in the emission intensity of both Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} ions, although the two luminescent centers exhibit markedly different quenching rates. The thermal evolution of the normalized emission spectra demonstrates that the luminescence of Ce3+\mathrm{Ce}^{3+} decreases rapidly above approximately 380 K, whereas the Mn2+\mathrm{Mn}^{2+} emission band centered at around 680 nm remains clearly observable at higher temperatures (Figure 4b). A quantitative analysis of the integrated emission intensity of Ce3+\mathrm{Ce}^{3+} for different Mn2+\mathrm{Mn}^{2+} concentrations reveals that the 5d→4f5d \to4f emission decreases to approximately 30% of its initial intensity at 380 K, followed by a dramatic reduction of more than two orders of magnitude upon further heating to 500 K (Figure 4c). Importantly, the concentration of Mn2+\mathrm{Mn}^{2+} has only a negligible influence on the thermal quenching behavior of Ce3+\mathrm{Ce}^{3+}, indicating that the thermal depopulation mechanism of the Ce3+\mathrm{Ce}^{3+} excited state is largely independent of the Mn2+\mathrm{Mn}^{2+} content.

Emission spectra and temperature-dependent emission properties of Ca₃Al₂O₆:0.5% Mn²⁺, 5% Ce³⁺

Figure 4. Emission spectra of Ca3_3Al2_2O6_6:0.5% Mn2+^{2+}, 5% Ce3+^{3+} measured as a function of temperature – a); thermal map of the normalized emission spectra of Ca3_3Al2_2O6_6:0.5% Mn2+^{2+}, 5% Ce3+^{3+} – b); temperature dependence of integrated emission intensity of Ce3+^{3+} -c) and of Mn2+^{2+} ions -d) for the samples with different concentration of Mn2+^{2+} ions; temperature dependence of LIR1LIR_1 – e), and corresponding SR1SR_1 – f); the influence of Mn2+^{2+} ions concentration on T@SR1maxT@SR_{1max} – g) and SR1maxSR_{1max} – h).

In contrast, the thermal quenching of Mn2+\mathrm{Mn}^{2+} luminescence is considerably less pronounced below 380 K, with the emission intensity decreasing to approximately 40% of its initial value at this temperature (Figure 4d). Above 380 K, however, the rate of thermal quenching increases substantially, similarly to the behavior observed for Ce3+\mathrm{Ce}^{3+}. In this case, a clear concentration dependence is evident, as increasing the Mn2+\mathrm{Mn}^{2+} content results in progressively faster thermal quenching of the Mn2+\mathrm{Mn}^{2+} emission. This behavior suggests the presence of an additional thermally activated depopulation pathway of the 4T1^{4}T_{1} excited state of Mn2+\mathrm{Mn}^{2+}, which becomes increasingly important at higher dopant concentrations. The most plausible mechanisms are either the formation of Mn2+\mathrm{Mn}^{2+}-related structural defects or thermally assisted Mn2+→Ce3+\mathrm{Mn}^{2+} \to\mathrm{Ce}^{3+} energy transfer.

Considering that Mn2+\mathrm{Mn}^{2+} substitutes Ca2+\mathrm{Ca}^{2+} in the investigated host without introducing charge imbalance, the formation of compensating structural defects is expected to be limited. Furthermore, no persistent luminescence was observed in Ca19Zn2(PO4)14:Mn2+-Ce3+\mathrm{Ca}_{19}\mathrm{Zn}_{2}(\mathrm{PO}_{4})_{14}:\mathrm{Mn}^{2+}\text{-}\mathrm{Ce}^{3+} indicating the absence of defect-related trapping centers that could significantly influence the emission process. Consequently, thermally activated Mn2+→Ce3+\mathrm{Mn}^{2+} \to\mathrm{Ce}^{3+} energy transfer appears to be the more plausible explanation for the observed concentration-dependent thermal quenching. Although Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} possess fundamentally different energy level schemes and therefore are expected to exhibit different intrinsic thermal responses, both ions display a similar increase in the quenching rate above approximately 380 K. This similarity originates from the dominant Ce3+→Mn2+\mathrm{Ce}^{3+}\to\mathrm{Mn}^{2+} energy transfer responsible for populating the excited state of Mn2+\mathrm{Mn}^{2+}, causing the thermal population dynamics of Mn2+\mathrm{Mn}^{2+} to closely follow those of the Ce3+\mathrm{Ce}^{3+} 5d5d excited state.

The thermal quenching of Ce3+\mathrm{Ce}^{3+} luminescence is attributed to the thermal ionization of electrons from the 5d5d excited state into the conduction band. This mechanism is supported by the nearly identical temperature dependence of the integrated Ce3+\mathrm{Ce}^{3+} emission intensity observed for phosphors doped solely with Ce3+\mathrm{Ce}^{3+} and those co-doped with Mn2+\mathrm{Mn}^{2+}. By fitting the experimental data with the Arrhenius equation, the 5d5d excited state of Ce3+\mathrm{Ce}^{3+} can be estimated to lie approximately ∼\sim2,100 cm−1^{-1} below the conduction band. The different thermal responses of Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} emission provide the basis for defining the luminescence intensity ratio LIR1LIR_1 as follows:

LIR1=Ce3+Mn2+=∫400nm560nm(5d→4F5/2,4F7/2) dλ∫580nm715nm(4T1→4A1) dλ(2)LIR_1=\frac{\mathrm{Ce}^{3+}}{\mathrm{Mn}^{2+}}=\frac{\int_{400\mathrm{nm}}^{560\mathrm{nm}}\left(5d\to{}^{4}F_{5/2},{}^{4}F_{7/2}\right)\,d\lambda}{\int_{580\mathrm{nm}}^{715\mathrm{nm}}\left({}^{4}T_1\to{}^{4}A_1\right)\,d\lambda} \tag*{(2)}

For samples containing low concentrations of Mn2+\mathrm{Mn}^{2+}, LIR1LIR_1 exhibits only minor temperature dependence up to approximately 300 K, after which it decreases rapidly, reaching nearly 10% of its initial value at 500 K (Figure 4e). Increasing the Mn2+\mathrm{Mn}^{2+} concentration introduces an initial increase of LIR1LIR_1 by approximately 10% up to 340 K, followed by thermal quenching at higher temperatures. This behavior is consistent with the concentration-dependent Mn2+→Ce3+\mathrm{Mn}^{2+}\to\mathrm{Ce}^{3+} energy transfer discussed above. To quantify the thermometric performance of the investigated phosphors, the relative thermal sensitivity SR1S_{R1} was calculated as follows:

SR=1LIRΔLIRΔT⋅100%(3)S_{R}=\frac{1}{LIR}\frac{\Delta LIR}{\Delta T}\cdot100\% \tag*{(3)}

where ΔLIR\Delta LIR stands for the change of LIRLIR corresponding to the change in temperature by ΔT\Delta T.

The temperature dependence of SR1S_{R1} is dominated by a single broad maximum located around 400 K (Figure 4f). However, both the temperature corresponding to the maximum sensitivity and the magnitude of SR1S_{R1} are strongly influenced by the Mn2+\mathrm{Mn}^{2+} concentration. Specifically, increasing the Mn2+\mathrm{Mn}^{2+} content from 0.05% to 5% shifts T@SRmax⁡T@S_{R\max} from 440 to 375 K (Figure 4g). The maximum relative thermal sensitivity (SRmax⁡S_{R\max}) reaches 0.9% K−1^{-1} for the sample containing 0.05% Mn2+\mathrm{Mn}^{2+} and increases to 1.25% K−1^{-1} for the composition with 0.5% Mn2+\mathrm{Mn}^{2+} (Figure 4h). A further increase in the Mn2+\mathrm{Mn}^{2+} concentration results in a gradual decline of SR1max⁡S_{R1\max}, indicating the existence of an optimal dopant concentration for achieving the best thermometric performance.

It should be noticed that except thermal quenching of the Mn2+^{2+} emission intensity observed in Ca3_3Al2_2O6_6:0.5% Mn2+^{2+}, Ce3+^{3+} at elevated temperatures, also a temperature-induced blue shift was recorded (Figure 5a). A similar temperature-induced spectral shift has previously been reported for several Mn2+\mathrm{Mn}^{2+}-doped hosts and has been attributed to the thermal population of higher-energy vibronic components of the 4T1{}^{4}T_{1} excited state [15, 16, 26, 52]. This effect becomes particularly evident when the thermal map of the normalized emission spectra is analyzed (Figure 5b). As can be clearly seen, increasing the temperature from 93 to 573 K shifts the spectral position of the Mn2+\mathrm{Mn}^{2+} emission band from 657 nm to 638 nm (Figure S6). Importantly, the magnitude and character of this spectral shift are essentially independent of the Mn2+\mathrm{Mn}^{2+} concentration, supporting its assignment to an intrinsic thermally activated spectroscopic process rather than to concentration-dependent interactions between Mn2+\mathrm{Mn}^{2+} ions.

Representative thermal evolution and thermometric properties of Ca3Al2O6:Ce3+, Mn2+ phosphors

Figure 5. Representative thermal evolution of normalized emission band of Mn2+^{2+} ions– a); thermal map of the emission band of Mn2+^{2+} emission for Ca3_3Al2_2O6_6:0.5% Mn2+^{2+}, 5% Ce3+^{3+} – b); thermal evolution of integrated emission intensity of Mn2+^{2+} ions calculated in the 590-635 nm spectral range – c); thermal evolution of LIR2LIR_2 – d); and corresponding SR2S_{R2} – e) the influence of Mn2+^{2+} ions concentration on the SR1maxS_{R1max} and SR2maxS_{R2max}– f).

The temperature-induced shift of the Mn2+\mathrm{Mn}^{2+} emission band can also be exploited for ratiometric luminescence thermometry by defining the luminescence intensity ratio LIR2_2 using the emission intensities integrated over two selected spectral ranges, which are significantly narrowed compared to the LIR1_1, namely:

LIR2=Ce3+Mn2+=∫460 nm505 nm(5d→4F5/2,4F7/2) dλ∫590 nm635 nm(4T1→6A1) dλ(4)LIR_{2} = \frac{\mathrm{Ce}^{3+}}{\mathrm{Mn}^{2+}} = \frac{\int_{460\,\mathrm{nm}}^{505\,\mathrm{nm}} \left(5d \to{}^{4}F_{5/2},{}^{4}F_{7/2}\right)\,\mathrm{d}\lambda}{\int_{590\,\mathrm{nm}}^{635\,\mathrm{nm}} \left({}^{4}T_{1} \to{}^{6}A_{1}\right)\,\mathrm{d}\lambda} \tag*{(4)}

It should be emphasized that these spectral ranges were selected empirically to provide an appropriate compromise between a pronounced temperature dependence of LIR2_2 and sufficiently high luminescence intensity in both spectral windows. Analysis of the temperature dependence of the luminescence signal integrated over the first spectral range (590-635 nm) reveals that, at low Mn2+\mathrm{Mn}^{2+} concentrations (Figure 5c), the intensity decreases only slightly up to approximately 300 K, whereas above this temperature the thermal quenching rate increases significantly. Importantly, increasing the Mn2+\mathrm{Mn}^{2+} concentration substantially modifies the shape of this dependence. For the sample containing 5% Mn2+\mathrm{Mn}^{2+}, the integrated luminescence intensity initially increases with temperature, reaching approximately 125% of its initial value at 253 K, and decreases upon further heating.

In contrast, the luminescence intensity integrated over the second spectral range (650–700 nm) decreases monotonically with increasing temperature and becomes almost completely quenched above 500 K (Figure S8). The distinctly different thermal evolution of the signals collected within the two spectral windows originates predominantly from the temperature-induced blueshift of the Mn2+^{2+} emission band. As the emission band shifts toward shorter wavelengths, the luminescence signal in the second spectral range decreases more rapidly, whereas the signal collected in the first spectral range becomes thermally stabilized at low Mn2+^{2+} concentrations and may even increase with temperature at higher Mn2+^{2+} concentrations. The combination of these opposing thermal responses results in a pronounced temperature dependence of the LIR2LIR_{2} and, consequently, high values of the relative temperature sensitivity - SR2S_{R2}.

Importantly, the maximum SR2S_{R2} values are considerably higher than those obtained for the LIR1LIR_{1}-based thermometric approach (Figure 5e). The highest SR2S_{R2} value of 1.5% K−1^{-1} is achieved for the sample containing 0.5% Mn2+^{2+}, demonstrating that the temperature-induced spectral shift of the Mn2+^{2+} emission band provides a particularly effective ratiometric thermometric readout in the investigated system (Figure 5f).

Visual thermometry based on Ca3_3Al2_2O6_6:Ce3+^{3+}, Mn2+^{2+}

The temperature-dependent thermal quenching of Ce3+^{3+} and Mn2+^{2+} emissions induces significant changes in the resulting emission color (Figure 6a). To visualize these temperature-induced color variations, the corresponding CIE1931 chromaticity coordinates were calculated (Figure 6b). The obtained results demonstrate that, at 93 K, all investigated phosphors exhibit gradual redshift in emission color with increasing Mn2+^{2+} concentration. This shift is associated with the enhanced contribution of Mn2+^{2+} emission relative to Ce3+^{3+} emission. Furthermore, increasing temperature causes a systematic redshift of the chromaticity coordinates for all Mn2+^{2+} concentrations. The effect of Mn2+^{2+} concentration on the thermal evolution of the xx and yy chromaticity coordinates is clearly demonstrated in Figure 6c and S9. Notably, the Mn2+\mathrm{Mn}^{2+} concentration has a more pronounced influence on the xx coordinate. With increasing Mn2+\mathrm{Mn}^{2+} concentration, the initial xx value at 93 K gradually increases. Compared with the yy coordinate, the xx coordinate exhibits significantly greater temperature dependence. Although the yy coordinate changes only slightly over the entire investigated temperature range, it increases monotonically with increasing temperature. Consequently, the relative sensitivity based on the xx chromaticity parameters (SRxSR_x) is higher than that based on the yy coordinate (SRySR_y) for all investigated samples. The highest relative sensitivities of the xx and yy coordinates are obtained for the samples co-doped with 0.5% and 0.2% of Mn2+\mathrm{Mn}^{2+}, respectively, reaching maximum values of SRxmax⁡=0.45SR_{x\max} = 0.45 %K−1^{-1} at 410 K and SRymax⁡=0.14SR_{y\max} = 0.14 %K−1^{-1} at 95 K (Figure 6d and S9). Furthermore, the temperatures corresponding to the maximum relative sensitivities of SR1SR_1, SR2SR_2 and SRxSR_x, exhibit a similar trend, shifting toward lower temperatures with increasing Mn2+\mathrm{Mn}^{2+} concentration. Additionally, it can be clearly seen that at elevated temperature the temperature at which SRmax⁡xSR_{\max x} was observed decrease with dopant concentration (Figure 6f). On the other hand, in the case of the T@SRmax⁡yT@SR_{\max y} only some fluctuation around 250 K can be observed. Another parameter which describes temperature-induced changes in the emission color is the chromaticity difference (CDCD), defined as follows:

Figure 6. Representative photographs of the luminescence of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} co-doped with x%x\% of Mn2+\mathrm{Mn}^{2+} (x=0.05x = 0.05-55) and 5%5\% of Ce3+\mathrm{Ce}^{3+} at different temperatures - a); the influence of temperature on the CIE1931 chromatic coordinates of the analyzed phosphors – b); the thermal evolution of xx chromatic CIE1931 coordinates of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}:x%Mn2+x\%\mathrm{Mn}^{2+}, 5%Ce3+5\%\mathrm{Ce}^{3+} for different Mn2+\mathrm{Mn}^{2+} concentrations - c); luminescence colour change (CDCD) as a function of Mn2+\mathrm{Mn}^{2+} concentration - d); thermal evolution of SRxS_{R_x} -e); the influence of the Mn2+\mathrm{Mn}^{2+} ions concentration on the SRmax⁡x,yS_{R_{\max x,y}} -f) and T@SRmax⁡x,yT@S_{R_{\max x,y}} -g).

CD=(xf−xi)2+(yf−yi)2(5)CD = \sqrt{(x_f-x_i)^2+(y_f-y_i)^2} \tag*{(5)}

where xfx_f, yfy_f and xix_i, yiy_i represents the final (high temperature) and the initial (low temperature) chromatic coordinates. The CDCD parameter initially increases from 0.15 for the sample with 0.05% of Mn2+\mathrm{Mn}^{2+} to 0.22 for the one with 0.5% of Mn2+\mathrm{Mn}^{2+}, and then gradually decreases with further increasing Mn2+\mathrm{Mn}^{2+} concentration (Figure 6g).

Conventional RGB-based thermometry

As demonstrated above, the temperature-induced variation in the emission color of Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} co-doped with x%x\% of Mn2+\mathrm{Mn}^{2+} (x=0.05x = 0.05-55) and 5%5\% of Ce3+\mathrm{Ce}^{3+} can be quantitatively evaluated through analysis of the CIE 1931 chromaticity coordinates. However, from a practical perspective, this approach may be inconvenient, as determination of the CIE 1931 parameters requires acquisition of the luminescence spectrum of the phosphor. Therefore, the same luminescence thermochromism observed in Ca3Al2O6:Mn2+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}:\mathrm{Mn}^{2+}, 5%Ce3+\mathrm{Ce}^{3+} can be exploited more straightforwardly through direct analysis of digital images of the emitted light. During image acquisition, a conventional digital camera inherently records two-dimensional intensity maps in the red (RR), green (GG), and blue (BB) channels. Owing to their distinct spectral response ranges, these channels can selectively probe the contributions of Ce3+\mathrm{Ce}^{3+} and Mn2+\mathrm{Mn}^{2+} luminescence. Consequently, pixel-by-pixel calculation of the ratio between appropriately selected RGB\mathit{RGB} intensity maps can provide a simple approach for spatially resolved temperature determination, eliminating the need for spectroscopic detection.

Representative RGB\mathit{RGB} intensity maps extracted from images of Ca3Al2O6:Mn2+\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6}:\mathrm{Mn}^{2+}, 5%Ce3+\mathrm{Ce}^{3+} containing different Mn2+\mathrm{Mn}^{2+} concentrations and recorded at 93 K are presented in Figure 7a. The analysis of the temperature evolution of the normalized RGB\mathit{RGB} channels pixel intensity for all samples reveals that these intensities decrease at elevated temperatures (Figure 7b, c, Figure S10). However, it can be noticed that Mn2+\mathrm{Mn}^{2+} ions concentration affects these trends. For samples with low Mn2+\mathrm{Mn}^{2+} concentrations, namely, 0.05 - 1% (Figure 7b), the three channels exhibit very similar rates of thermal changes. In contrast, at higher Mn2+\mathrm{Mn}^{2+} concentrations (2-5 % of Mn2+\mathrm{Mn}^{2+}), the responses of the individual channels become increasingly distinct, with the RR channel showing markedly different temperature dependence compared with the GG and BB channels. These results indicate that the RGB\mathit{RGB} channel intensities are not only temperature-dependent, but can also be tuned through the Mn2+\mathrm{Mn}^{2+} concentration. Looking forward to developing an optical thermometer based on the RGB\mathit{RGB} channels, different thermometric parameters derived from these channels were considered. In principle, a ratiometric parameter defined from two RGB\mathit{RGB} channels should also exhibit a temperature dependence if the individual channels respond differently to temperature. However, for samples with Mn2+\mathrm{Mn}^{2+} concentrations between 0.05% and 1%, the RR, GG and BB channels display very similar temperature trends. As a result, the corresponding ratiometric parameters remain nearly constant with temperature, limiting their suitability as thermometric parameters. These samples were therefore excluded from the following analysis.

Representative photographs of luminescence samples and RGB-channel thermal analysis

Figure 7. Representative photographs of luminescence of the Ca3Al2O6:Mn2+\mathrm{Ca_3Al_2O_6}:\mathrm{Mn^{2+}}, 5% Ce3+\mathrm{Ce^{3+}} samples taken at 93 K and the extraction of the intensity recorded in the R, G, B channels -a); temperature dependance of the normalized RGB channels pixel intensity for the Ca3Al2O6\mathrm{Ca_3Al_2O_6}:0.05% Mn2+\mathrm{Mn^{2+}}, 5%Ce3+\mathrm{Ce^{3+}} -b) and Ca3Al2O6\mathrm{Ca_3Al_2O_6}:5% Mn2+\mathrm{Mn^{2+}}, 5% Ce3+\mathrm{Ce^{3+}} materials -c); temperature dependance of the B/RB/R – d) and G/RG/R – e) ratiometric parameters (open symbols) and their corresponding relative thermal sensitivity, SRS_R (blue solid line) of Ca3Al2O6\mathrm{Ca_3Al_2O_6}:5% Mn2+\mathrm{Mn^{2+}}, 5% Ce3+\mathrm{Ce^{3+}} sample (red solid lines in both stand for the linear fits as the best fits to the experimental data, see Table S1. The pale pink shadowed region represents the excluded temperature region.); doughnut chart of the relative weight (values on the chart are the β\beta-weights) of the thermometric parameters B/RB/R and G/RG/R considered for the MLR analysis within the range of 93-333 K for the sample Ca3Al2O6\mathrm{Ca_3Al_2O_6}:5% Mn2+\mathrm{Mn^{2+}}, 5% Ce3+\mathrm{Ce^{3+}} -f); correlation between the measured temperature and the calculated temperature by the MLR model – g); the influence of the dopant concentration on the thermal dependence of SRS_R -h).

In the case of the high dopant concentration both B/RB/R and G/RG/R ratiometric parameters reveal monotonic thermal trend up to 333 K (Figure 7d, Figure 7e). Therefore, they can be exploited for temperature sensing. In order to perform a calibration procedure, a phenomenological straight line calibration curve for both B/RB/R and G/RG/R was adopted as shown in Figure 7d and Figure 7e. The temperature dependence of the SRS_{\mathrm{R}}, depicted in Figure 7c, Figure 7d, presents an increase with temperature, reaching maximum values of 0.818% K−1^{-1} and 0.371% K−1^{-1} at 333 K, for B/RB/R and G/RG/R respectively (Figure 7c, Figure 7d). It is worth noting that the relative sensitivity associated with the B/RB/R ratio decreases as the Mn2+\mathrm{Mn}^{2+} concentration decreases, with a similar trend observed across all three samples. A similar behaviour was observed for the G/RG/R ratio. The only exception was sample with 0.5% of Mn2+\mathrm{Mn}^{2+} (Figure S11) concentration, for which the B/GB/G ratio was analysed instead of G/RG/R. Once again, these results suggest that the sensitivity of the optical thermometer can be tuned by varying the Mn2+\mathrm{Mn}^{2+} concentration.

Implementation of MLR to RGB-based luminescence thermometry

As it can be seen the obtained thermal sensitivities of the ratiometric parameter based on RGBRGB analysis is not very high in the case of Ca3Al2O6:Mn2+,Ce3+\mathrm{Ca}_3\mathrm{Al}_2\mathrm{O}_6:\mathrm{Mn}^{2+}, \mathrm{Ce}^{3+}. Therefore, we introduce here the multiple linear regression (MLR) approach to exploit the complementary temperature-dependent information encoded in different RGBRGB channel ratios and enhance the thermometric performance beyond that achievable using individual ratiometric parameters. Although, MLR was already used in temperature sensing[33, 34, 35, 56], to the best of our knowledge, the combination of multiple ratiometric RGBRGB parameters with MLR has not previously been explored for optical thermometry. Considering the nearly linear temperature dependence exhibited by the RGBRGB channel ratios, their simultaneous analysis through MLR provides a straightforward multiparametric framework to improve the sensitivity of the system. MLR has been successfully introduced in luminescence thermometry as a means of evaluating the combined contribution of several independent temperature-dependent variables to a single experimental response, boosting as a result the performance of the optical sensor. Within this framework, the MLR model can be expressed as:

y=β0+∑i=1nβixi+ε(6)y = \beta_{0} + \sum_{i=1}^{n} \beta_{i}x_{i} + \varepsilon \tag*{(6)}

where yy represents the dependent variable (in this study, temperature), xix_i are the independent variables, also referred to as predictors, βi\beta_i are the regression coefficients associated with each predictor, and ε\varepsilon denotes the residual random error. The regression coefficients quantify the variation in the dependent variable resulting from a one-unit change in the corresponding predictor, while the remaining predictors are kept constant. The error term accounts for unobserved factors influencing the dependent variable that are not explicitly included in the model. In the present work, the predictors correspond to the ratiometric parameters based on the RGBRGB channels, while temperature is treated as the response variable. To ensure the validity of the linear regression model, the selected predictors were required to satisfy two main criteria: (i) they must exhibit a linear dependence on temperature, and (ii) they must share the same operational temperature range. In the case of Ca3Al2O6:5%Ce3+:5%Mn2+\mathrm{Ca_3Al_2O_6}:5\%\mathrm{Ce^{3+}}:5\%\mathrm{Mn^{2+}} two selected thermometric parameters, namely B/RB/R and G/RG/R exhibit linear dependence with temperature and share the same operational ranges, namely from 93 to 333 K. The combination of these two predictors was carried out following the procedure described in the literature, and the corresponding β\beta-coefficients were calculated [31, 57]. B/RB/R presents a higher β\beta-weight than G/RG/R (76.1% and 23.9% respectively, Figure 7f). According to the model, B/RB/R plays a more significant role in the estimation of the temperature for a given value of G/RG/R. As it can be seen the implementation of MLR for this phosphor enables to obtain the good correlations between the measured temperatures and those predicted by the MLR model (Figure 7g). Additionally, it can be clearly shown that the SRS_{R} obtained based on MLR are significantly much higher comparing to the one obtained based on solely B/RB/R and G/RG/R for all Mn2+^{2+} ions concentrations (Figure 7h, Figure S12). The MLR model yielded a maximum SRS_{R} value of 1.70% K−1^{-1} for 5% Mn2+^{2+}, representing approximately a threefold improvement compared with the SRS_{R} values obtained from single-parametric sensing in the same temperature range (0.63% K−1^{-1} for B/RB/R). Overall, these results demonstrate that the advantages previously reported for MLR-based multiparametric optical sensing can also be extended to RGB\mathit{RGB}-based thermometry and the obtained thermal sensitivity is the highest among all up to now reported Mn2+^{2+} based luminescent thermometers (Table 1). In particular, the simultaneous combination of different RGB\mathit{RGB} ratiometric parameters allows the complementary temperature-dependent information contained in the individual colour channels to be exploited, resulting in a substantial improvement of the SRS_{R}. This work therefore introduces the use of MLR for the combined analysis of RGB\mathit{RGB} ratiometric parameters in optical thermometry, providing a new strategy to improve the performance of RGB\mathit{RGB}-based luminescent thermometers beyond that achievable using individual channel ratios.

PhosphorsChannelsSRS_{R}Ref
[% K−1^{-1}]
La2_2MoO6_6:Yb3+^{3+}/Tm3+^{3+}R/G1.8[58]
Ca19_{19}Ce(PO4_4)14_{14}:Mn2+^{2+}, Ce3+^{3+}R/G0.69[15]
Ca19_{19}Zn2_2(PO4_4)14_{14}:Mn2+^{2+}, Ce3+^{3+}R/G0.72[59]
Ca3_3Al2_2O6_6: Mn2+^{2+}, Ce3+^{3+}B/R0.8This work
Ca3_3Al2_2O6_6: Mn2+^{2+}, Ce3+^{3+}G/R0.4This work
Ca3_3Al2_2O6_6: Mn2+^{2+}, Ce3+^{3+}MLR1.7This work

Table 1. Comparison of the thermometric performance of RGB luminescence thermometry.

Discussion

In this work, we introduce, for the first time, a multiple-linear-regression-enhanced RGB-based luminescence thermometry strategy that combines multispectral image analysis with 2D spatial temperature mapping using a conventional digital camera. We used a Ca3AlO2O6\mathrm{Ca_3AlO_2O_6} material co-doped with Mn2+\mathrm{Mn^{2+}} and Ce3+\mathrm{Ce^{3+}} ions as a representative system, in order to systematically investigate the effect of dopant concentration and temperature on its thermometric performance for visual thermal sensing and imaging. The incorporation of Ce3+\mathrm{Ce^{3+}} and Mn2+\mathrm{Mn^{2+}} ions into the investigated system enables luminescence in the blue and red spectral ranges, respectively, originating from the 5d1→4f15d^1 \to4f^1 transition of Ce3+\mathrm{Ce^{3+}} and the 4T1(4G)→6A1(6S){}^{4}\mathrm{T}_{1}({}^{4}\mathrm{G}) \to{}^{6}\mathrm{A}_{1}({}^{6}\mathrm{S}) transition of Mn2+\mathrm{Mn^{2+}}. Although the spectroscopic analysis of Ca3AlO2O6:Ce3+\mathrm{Ca_3AlO_2O_6:Ce^{3+}} revealed the presence of several crystallographic sites occupied by Ce3+\mathrm{Ce^{3+}} ions, the dominant luminescence contribution was found to originate from Ce3+\mathrm{Ce^{3+}} ions located at the Ca(5) site.

Comparison of the excitation spectra of Ca3AlO2O6:Ce3+\mathrm{Ca_3AlO_2O_6:Ce^{3+}} and Ca3AlO2O6:Ce3+,Mn2+\mathrm{Ca_3AlO_2O_6:Ce^{3+},Mn^{2+}} revealed that Ce3+→Mn2+\mathrm{Ce^{3+} \to Mn^{2+}} energy transfer constitutes the dominant pathway responsible for populating the 4T1(4G){}^{4}\mathrm{T}_{1}({}^{4}\mathrm{G}) excited state of Mn2+\mathrm{Mn^{2+}} ions. Consequently, owing to the increasing number of Mn2+\mathrm{Mn^{2+}} luminescent centers and the efficient Ce3+→Mn2+\mathrm{Ce^{3+} \to Mn^{2+}} energy transfer, increasing the Mn2+\mathrm{Mn^{2+}} concentration progressively enhances the intensity of the Mn2+\mathrm{Mn^{2+}}-related 4T1(4G)→6A1(6S){}^{4}\mathrm{T}_{1}({}^{4}\mathrm{G}) \to{}^{6}\mathrm{A}_{1}({}^{6}\mathrm{S}) emission band relative to the Ce3+\mathrm{Ce^{3+}} emission. As a result, the emission color of Ca3AlO2O6:Ce3+,Mn2+\mathrm{Ca_3AlO_2O_6:Ce^{3+},Mn^{2+}} can be continuously tuned from blue to red by increasing the Mn2+\mathrm{Mn^{2+}} concentration.

Temperature-dependent spectroscopic analysis revealed that Mn2+\mathrm{Mn^{2+}} luminescence exhibits higher thermal stability than the Ce3+\mathrm{Ce^{3+}} emission. At the same time, the comparable temperature dependence of the emission intensities of both ions observed up to approximately 400 K can be explained by thermalization of the Ce3+\mathrm{Ce^{3+}} excited state via the conduction band. The different thermal responses of Ce3+\mathrm{Ce^{3+}} and Mn2+\mathrm{Mn^{2+}} luminescence enable ratiometric temperature readout based on the intensity ratio of their respective emission bands (LIR1LIR_{1}), yielding a maximum relative sensitivity of SRmax⁡=1.24S_{R\max} = 1.24 % K−1^{-1} for the sample containing 0.5% Mn2+^{2+}.

Importantly, increasing the Mn2+^{2+} concentration results in a monotonic shift of the temperature corresponding to the maximum relative sensitivity, T@SRmax⁡T@S_{R\max}, from 442 K for 0.05% Mn2+^{2+} to 378 K for 5% Mn2+^{2+}, demonstrating the possibility of tailoring the optimal operating temperature range through appropriate control of the dopant concentration.

In addition to the changes in emission intensity, increasing temperature induces a pronounced blueshift of the Mn2+^{2+} emission band, which can be attributed to the thermal population of higher-energy vibronic components of the Mn2+^{2+} excited state. This effect was exploited to define an additional thermometric parameter, LIR2LIR_{2}, in which only the short-wavelength portion of the Mn2+^{2+} emission band was considered. This approach significantly enhanced the thermometric response compared with that obtained using LIR1LIR_{1}, resulting in SRmax⁡S_{R\max} = 1.5 % K−1^{-1} for the sample containing 0.5% Mn2+^{2+}. The pronounced temperature-induced modification of the emission color of Ca3_{3}AlO2_{2}O6_{6}:Ce3+^{3+},Mn2+^{2+} additionally enables temperature determination through analysis of the CIE 1931 chromaticity coordinates, with maximum relative sensitivities of SRx,max⁡S_{Rx,\max} = 0.45% K−1^{-1} and SRy,max⁡S_{Ry,\max} = 0.14% K−1^{-1}.

Notably, the thermochromic response of the Ca3_{3}AlO2_{2}O6_{6}:Ce3+^{3+}, Mn2+^{2+} material can be directly analyzed using a conventional digital camera, which is crucial from the perspective of practical thermal imaging. In this approach, ratios of the two-dimensional intensity maps recorded by the RR, GG, and BB channels provide spatially resolved information on the temperature distribution and therefore enable straightforward RGB-based thermal imaging without the need for spectrally resolved detection. Furthermore, for the first time, a multiple linear regression (MLR) approach was implemented to enhance the thermometric performance of RGB-based thermal imaging. By simultaneously exploiting the temperature-dependent information encoded in the RGB channels, the MLR-based approach resulted in an approximately 3-fold enhancement of the relative sensitivity, reaching SRmax⁡=1.7 % K−1S_{R\max} = 1.7\ \%\,\mathrm{K}^{-1} for the sample containing 5% Mn2+\mathrm{Mn}^{2+}. Overall, these results demonstrate that the combination of luminescence thermochromism, RGB-based image analysis, and MLR provides a simple yet highly sensitive strategy for spatially resolved thermal sensing and imaging using a conventional digital camera.

Materials and Methods

Synthesis

The phosphor materials, Ca3Al2O6\mathrm{Ca}_{3}\mathrm{Al}_{2}\mathrm{O}_{6} co-doped with Mn2+\mathrm{Mn}^{2+} and Ce3+\mathrm{Ce}^{3+}, were synthesized by a conventional solid-state reaction. CaO (Thermo Fisher Scientific, 99.998%), Al2O3\mathrm{Al}_{2}\mathrm{O}_{3} (Thermo Fisher Scientific, 99.995%),), MnCO3\mathrm{MnCO}_{3} (Thermo Fisher Scientific, 99.985%) and Ce(NO3)3⋅6H2O\mathrm{Ce(NO}_{3}\mathrm{)}_{3}\cdot6\mathrm{H}_{2}\mathrm{O} (Alfa Aesar, 99.998%) were used as starting materials. According to the designed compositions, the proper amounts of these above powders were weighed and ground in an agate mortar. The grounded mixtures were transferred to corundum crucibles and annealed in an air atmosphere at 1573 K for 4 hours, after that in a reducing atmosphere at 1573 K for 4 hours. The final samples were naturally cooled to the room temperature and grounded to a powder for further evaluations.

Characterization

The powder X-ray diffraction (XRD) patterns were recorded using a PANalytical X’Pert Pro diffractometer using Ni-filtered Cu Kα\alpha radiation (V = 40 kV, I = 30 mA). Measurements were performed in the 2θ=10−90∘2\theta= 10 - 90^\circ range with a 30 min measurement time. Scanning electron microscopy (SEM) was taken by FEI Nova NanoSEM 230 equipped with an EDAX Genesis XM4 energy dispersive spectrometer to verify the morphology of the samples and the distribution of its elements by Energy-Dispersive X-ray Spectroscopy (EDS) (V = 30 kV for SEM and V = 5 kV for EDS mapping). Samples were prepared by dispersing the powder in a few drops of methanol. A drop of the resulting suspension was deposited onto a carbon stub and allowed to dry. This preparation method ensured stable positioning of the sample during SEM imaging while minimizing charging effects under electron beam irradiation.

The optical properties including emission, excitation spectra and luminescence kinetics were measured by a FLS1000 Fluorescence Spectrometer from Edinburgh Instruments, equipped with a 450 W xenon lamp and μ\muFlash pulsed lamp as excitation sources, and an R928 photomultiplier tube from Hamamatsu as a detector. The temperature-dependent measurements were performed using a THMS 600 heating-cooling stage from Linkam, providing temperature stability of 0.1 K and a set point resolution of 0.1 K.

The digital images were taken using a Canon EOS 400D camera using a 10 s integration time, 14.3 lp/nm spatial resolution. After acquiring the luminescence images, the individual R, G and B channels were extracted and emission maps based on their intensity ratios were subsequently generated. All image processing steps were performed using IrfanView 64 (version 4.51).

Acknowledgements

This work was supported by the Foundation for Polish Science under First Team FENG.02.02-IP.05-0018/23 project with funds from the 2nd Priority of the Program European Funds for Modern Economy 2021-2027 (FENG). Authors would like to acknowledge dr Damian Szymanski for help in the EDX analysis.

References

  1. [1]D. Jaque, F. Vetrone, Luminescence nanothermometry. Nanoscale 4, 4301–4326 (2012).DOI
  2. [2]E. Ximendes, R. Marin, L. D. Carlos, D. Jaque, Less is more: dimensionality reduction as a general strategy for more precise luminescence thermometry. Light Sci. Appl. 11 (2022).DOI
  3. [3]A. Bednarkiewicz, J. Drabik, K. Trejgis, D. Jaque, E. Ximendes, L. Marciniak, Luminescence based temperature bio-imaging: Status, challenges, and perspectives. Appl. Phys. Rev. 8 (2021).
  4. [4]C. D. S. Brites, R. Marin, M. Suta, A. N. Carneiro Neto, E. Ximendes, D. Jaque, L. D. Carlos, Spotlight on Luminescence Thermometry: Basics, Challenges, and Cutting-Edge Applications. Advanced Materials 35 (2023).DOI
  5. [5]C. D. S. Brites, P. P. Lima, N. J. O. Silva, A. Millán, V. S. Amaral, F. Palacio, L. D. Carlos, Thermometry at the nanoscale. Nanoscale 4, 4799–4829 (2012).
  6. [6]C. D. S. Brites, A. Millán, L. D. Carlos, Lanthanides in Luminescent Thermometry. Handbook on the Physics and Chemistry of Rare Earths 49, 339–427 (2016).DOI
  7. [7]A. Bednarkiewicz, L. Marciniak, L. D. Carlos, D. Jaque, Standardizing luminescence nanothermometry for biomedical applications. Nanoscale 12, 14405–14421 (2020).DOI
  8. [8]M. D. Dramićanin, Trends in luminescence thermometry. J. Appl. Phys. 128 (2020).DOI
  9. [9]C. D. S. Brites, P. P. Lima, N. J. O. Silva, A. Millán, V. S. Amaral, F. Palacio, L. D. Carlos, Thermometry at the nanoscale. Nanoscale 4, 4799–4829 (2012).
  10. [10]B. Harrington, Z. Ye, L. Signor, A. D. Pickel, Luminescence Thermometry Beyond the Biological Realm. ACS Nano 4, 30–61 (2024).DOI
  11. [11]C. D. S. Brites, S. Balabhadra, L. D. Carlos, Lanthanide-Based Thermometers: At the Cutting-Edge of Luminescence Thermometry. Adv. Opt. Mater. 7 (2019).
  12. [12]J. M. Wagner, C. Winters, R. B. Berke, E. M. C. Jones, Full-Field Measurement Uncertainty Quantification for Luminescence Phosphor Thermography on Surfaces in 3D Space. Exp. Mech., doi: 10.1007/S11340-026-01364-5 (2026).DOI
  13. [13]J. Xiong, M. Zhao, X. Han, Z. Cao, X. Wei, Y. Chen, C. Duan, M. Yin, Real-time micro-scale temperature imaging at low cost based on fluorescent intensity ratio. Sci. Rep. 7 (2017).
  14. [14]T. Gavrilović, J. Periša, Z. Ristić, K. Elzbieciak-Piecka, Ł. Marciniak, C. G. Ma, Ž. Antić, M. D. Dramićanin, Thermal history forensics using the emission intensity ratio of YVO4:Eu3+ phosphor. Measurement 202, 111942 (2022).DOI
  15. [15]Y. Abe, M. Szymczak, J. Zeler, R. Szukiewicz, L. Marciniak, Interplay of Optical Traps and Vibronic Thermalization Governing Mn2+ Luminescence in Ca19Ce(PO4)14: Implications for Temperature Sensing and Thermal Threshold Indicator. Laser Photon. Rev., e71411 (2026).
  16. [16]Y. Wu, F. Li, Y. Wu, H. Wang, L. Gu, J. Zhang, Y. Qi, L. Meng, N. Kong, Y. Chai, Q. Hu, Z. Xing, W. Ren, F. Li, X. Zhu, Lanthanide luminescence nanothermometer with working wavelength beyond 1500 nm for cerebrovascular temperature imaging in vivo. Nature Communications 2024 15: 15, 2341- (2024).DOI
  17. [17]W. Piotrowski, K. Trejgis, K. Maciejewska, K. Ledwa, B. Fond, L. Marciniak, Thermochromic Luminescent Nanomaterials Based on Mn4+/Tb3+Codoping for Temperature Imaging with Digital Cameras. ACS Appl. Mater. Interfaces 12, 44039–44048 (2020).DOI
  18. [18]K. Elzbieciak-Piecka, W. M. Piotrowski, M. D. Dramic̨anin, L. Marciniak, Understanding the power of luminescence ratiometric thermal history indicators driven by phase transitions: the case of Eu3+ doped LaVO4. Dalton Transactions 52, 6077–6084 (2023).
  19. [19]S. M. Bathaei, J. Thiel, M. Böke, T. Endres, N. Jüngst, A. von Keudell, C. Schulz, Temperature and phase evolution of individual ion and iron-oxide particles during combustion and hydrogen plasma reduction. Proceedings of the Combustion Institute 42 (2026).DOI
  20. [20]H. Zhang, Y. Wang, S. Su, D. Xu, R. Li, H. Xu, B. Teng, W. Wang, T. Qiu, Z. Wu, K. Wang, G. Zhu, C. Hu, S. Sun, J. Jia, D. Zhong, La2MoO6: Yb3+/Tm3+ upconversion phosphors enabling dual-mode high-sensitivity and wide-color-gamut visual optical thermometry. J. Alloys Compd. 1079 (2026).
  21. [21]J. Periša, B. Milićević, A. Ćirić, I. Zeković, V. Đorđević, Ž. Antić, M. D. Dramićanin, Advancing luminescence thermometry: Employing multiple fluorescence intensity ratios of YAG:Er3+/Mn4+ nanocrystals for supersensitive temperature sensing. Ceram. Int. 51, 23224–23232 (2025).DOI
  22. [22]R. S. Baltieri, A. Reupert, D. Manzani, L. Wondraczek, Remote Luminescent Temperature Sensing Using 3D-Printed Eu(III)-Doped Micropolymers at the Tip of an Optical Fiber. Adv. Mater. Technol. 10 (2025).DOI
  23. [23]G. Li, Y. Tian, Y. Zhao, J. Lin, Recent progress in luminescence tuning of Ce3+ and Eu2+-activated phosphors for pc-WLEDs. Chem. Soc. Rev. 44, 8688–8713 (2015).DOI
  24. [24]C. Xu, X. Qu, Cerium oxide nanoparticle: a remarkably versatile rare earth nanomaterial for biological applications. NPG Asia Mater. 6 (2014).
  25. [25]V. Bachmann, C. Ronda, A. Meijerink, Temperature quenching of yellow Ce3+ luminescence in YAG:Ce. Chemistry of Materials 21, 2077–2084 (2009).
  26. [26]S. Adachi, Mn4+ vs Mn2+—A comparative study as efficient activator ions in phosphor materials: A review. J. Lumin. 263 (2023).DOI
  27. [27]4+ Mn, 3+ Cr, 2+ Mn, 2+ Eu, 3+ Eu, Review—Temperature Dependence of Transition-Metal and Rare-Earth Ion Luminescence (Mn4+, Cr3+, Mn2+, Eu2+, Eu3+, Tb3+, etc.) I: Fundamental Principles. ECS Journal of Solid State Science and Technology 11, 096002 (2022).
  28. [28]C. Liang, Y. Fu, X. Teng, K. Liu, H. You, J. He, Codoped Tb3+ and Mn2+ induced tunable emission and energy transfer in Ca19Zn2(PO4)14:Ce3+,Tb3+,Mn2+. New Journal of Chemistry 42, 16729–16734 (2018).
  29. [29]W. M. Piotrowski, K. Kniec-Stec, M. Suta, B. Bogielski, B. Pozniak, L. Marciniak, Positive luminescence thermal coefficient of Mn2+ ions for highly sensitive luminescence thermometry. Chemical Engineering Journal 464, 142492 (2023).DOI
  30. [30]Q. Zhou, L. Dolgov, A. M. Srivastava, L. Zhou, Z. Wang, J. Shi, M. D. Dramićanin, M. G. Brik, M. Wu, Mn2+ and Mn4+ red phosphors: Synthesis, luminescence and applications in WLEDs. A review. J. Mater. Chem. C Mater. 6, 2652–2671 (2018).DOI
  31. [31]P. Woźny, M. A. Hernández-Rodríguez, K. Kamada, A. Yoshikawa, N. Majewska, S. Mahlik, M. Runowski, U. R. Rodríguez-Mendoza, V. Lavín, Multiparametric Optical Pressure Sensing in YAG:Ce3+ Enabled by Multiple Linear Regression: A New Paradigm for Superior Sensor Performance. Laser Photon. Rev. 20, e02673 (2026).DOI
  32. [32]F. E. Maturi, C. D. S. Brites, E. C. Ximendes, C. Mills, B. Olsen, D. Jaque, S. J. L. Ribeiro, L. D. Carlos, Going Above and Beyond: A Tenfold Gain in the Performance of Luminescence Thermometers Joining Multiparametric Sensing and Multiple Regression. Laser Photon. Rev. 15 (2021).
  33. [33]F. Zhao, T. Zheng, P. Woźny, M. A. Hernández-Rodríguez, S. Xu, I. R. Martín, M. Runowski, Temperature-Driven Emission Redistribution of Yb2+ in SrB4O7 Enables Highly Sensitive Optical Thermometry Supported by Multiple Linear Regression. Advanced Science, doi: 10.1002/ADVS.75586 (2026).DOI
  34. [34]S. E. P. da Silva, J. C. de Lima, L. L. da Luz, J. A. B. da Silva, I. Malvestiti, R. L. Longo, Expanding the primary thermometry based on the excitation spectra to aqueous solutions with Eu(III) complexes and multiple linear regression. J. Lumin. 286 (2025).
  35. [35]W. Xu, C. Xu, J. Cui, C. Hu, G. Wen, L. Zheng, Z. Zhang, Z. Sun, Y. Zhang, Luminescence thermometry driven by a support vector machine: a strategy toward precise thermal sensing. Opt. Lett. 49, 606 (2024).DOI
  36. [36]H. Ju, W. Deng, B. Wang, J. Liu, X. Tao, S. Xu, The structure and luminescence properties of green Ca 3Al 2O 6:Bi 3+ phosphors. J. Alloys Compd. 516, 153–156 (2012).
  37. [37]T. Hirsch, T. Matschei, D. Stephan, The hydration of tricalcium aluminate (Ca3Al2O6) in Portland cement-related systems: A review. Cem. Concr. Res. 168 (2023).DOI
  38. [38]J. Zhang, Y. He, Z. Qiu, W. Zhang, W. Zhou, L. Yu, S. Lian, Site-sensitive energy transfer modes in Ca3Al2O6: Ce3+ /Tb3+ /Mn2+ phosphors. Journal of the Chemical Society. Dalton Transactions 43, 18134–18145 (2014).
  39. [39]J. ying Jing, T. yu Li, X. wei Zhang, S. dong Wang, J. Feng, W. A. Turmel, W. ying Li, Enhanced CO2 sorption performance of CaO/Ca3Al2O6 sorbents and its sintering-resistance mechanism. Appl. Energy 199, 225–233 (2017).DOI
  40. [40]B. M. Mohamed, J. H. Sharp, Kinetics and mechanism of formation of tricalcium aluminate, Ca3Al2O6. Thermochim. Acta 388, 105–114 (2002).DOI
  41. [41]M. Benitez-Guerrero, J. M. Valverde, P. E. Sanchez-Jimenez, A. Perejon, L. A. Perez-Maqueda, Calcium-Looping performance of mechanically modified Al2O3-CaO composites for energy storage and CO2 capture. Chemical Engineering Journal 334, 2343–2355 (2018).
  42. [42]G. Kakali, S. Tsivilis, E. Aggeli, M. Bati, Hydration products of C3A, C3S and Portland cement in the presence of CaCO3. Cem. Concr. Res. 30, 1073–1077 (2000).DOI
  43. [43]P. Mondal, J. W. Jeffery, The crystal structure of tricalcium aluminate, Ca 3 Al 2 O 6 . Acta Crystallogr. B 31, 689–697 (1975).
  44. [44]W. Chen, Y. Wang, X. Xu, W. Zeng, Y. Gong, A new long-lasting phosphor Ce3+ doped Ca3Al 2O6. ECS Solid State Letters 1, R17 (2012).DOI
  45. [45]P. Mondal, J. W. Jeffery, The crystal structure of tricalcium aluminate, Ca3Al2O6. Acta Crystallographica Section B 31, 689–697 (1975).
  46. [46]V. Bachmann, C. Ronda, A. Meijerink, Temperature Quenching of Yellow Ce3+ Luminescence in YAG:Ce. Chemistry of Materials 21, 2077–2084 (2009).
  47. [47]Z. Xia, A. Meijerink, Ce3+-Doped garnet phosphors: composition modification, luminescence properties and applications. Chem. Soc. Rev. 46, 275–299 (2017).DOI
  48. [48]P. Dorenbos, The 5d level positions of the trivalent lanthanides in inorganic compounds. J. Lumin. 91, 155–176 (2000).DOI
  49. [49]E. V.D. Van Loef, P. Dorenbos, C. W. E. Van Eijk, K. Krämer, H. U. Güdel, High-energy-resolution scintillator: Ce3+ activated LaBr3. Appl. Phys. Lett. 79, 1573–1575 (2001).DOI
  50. [50]Z. Ci, Q. Sun, M. Sun, X. Jiang, S. Qin, Y. Wang, Structure, photoluminescence and thermal properties of Ce3+, Mn2+ co-doped phosphosilicate Sr/La3[(PO4)2.5(SiO4)3(BO4) 0.5](BO2) emission-tunable phosphor. J. Mater. Chem. C Mater. 2, 5850–5856 (2014).
  51. [51]L. G. Van Uitert, An empirical relation fitting the position in energy of the lower d-band edge for Eu2+ or Ce3+ in various compounds. J. Lumin. 29, 1–9 (1984).
  52. [52]S. Adachi, Review—Photoluminescence Spectroscopy of Mn 2+-Activated Phosphors: Part II. Some Representative Phosphors . ECS Journal of Solid State Science and Technology 12, 126004 (2023).DOI
  53. [53]S. Li, W. Hu, M. G. Brik, S. Lian, Z. Qiu, Achieving highly thermostable red emission in singly Mn2+-doped BaXP2O7 (X = Mg/Zn) via self-reduction. Inorg. Chem. Front. 9, 3224–3232 (2022).
  54. [54]A. Deng, Z. Wang, X. Zhou, W. Geng, MgGd4Si3O13:Ce3+, Mn2+: A Dual-Excitation Temperature Sensor. ACS Omega 7, 6481–6487 (2022).DOI
  55. [55]Q. Zhou, L. Dolgov, A. M. Srivastava, L. Zhou, Z. Wang, J. Shi, M. D. Damiáncin, M. G. Brik, M. Wu, Mn2+ and Mn4+ red phosphors: Synthesis, luminescence and applications in WLEDs. A review. J. Mater. Chem. C Mater. 6, 2652–2671 (2018).DOI
  56. [56]L. F. Saraiva, A. G. Bispo-Jr, A. L. Costa, F. A. Sigoli, S. A. M. Lima, A. M. Pires, Dimensionality Reduction Expands the Frontiers of Lanthanide Luminescence Thermometry Beyond Single-Parametric Thermal Sensing. Chemistry of Materials 37, 3125–3136 (2025).DOI
  57. [57]F. E. Maturi, C. D. S. Brites, E. C. Ximendes, C. Mills, B. Olsen, D. Jaque, S. J. L. Ribeiro, L. D. Carlos, Going Above and Beyond: A Tenfold Gain in the Performance of Luminescence Thermometers Joining Multiparametric Sensing and Multiple Regression. Laser Photon. Rev. 15, 2100301 (2021).
  58. [58]H. Zhang, Y. Wang, S. Su, D. Xu, R. Li, H. Xu, B. Teng, W. Wang, T. Qiu, Z. Wu, K. Wang, G. Zhu, C. Hu, S. Sun, J. Jia, D. Zhong, La2MoO6: Yb3+/Tm3+ upconversion phosphors enabling dual-mode high-sensitivity and wide-color-gamut visual optical thermometry. J. Alloys Compd. 1079, 190051 (2026).DOI
  59. [59]Y. Abe, M. Szymczak, J. Zeler, L. Marciniak, Unusual Thermally Induced Blueshift and Emission Amplification of Mn2+ Ions Enable Filter-Free Luminescent Thermal Imaging. Advanced Science 13, e75943 (2026).

Paper details

vlnc:W_zgwg99zf
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents