betaFeedback

WorksEngineering

A Discrete Digital Isolator with Shielded Planar Transformer for Gate Driver Applications

Abstract

Galvanically isolated gate drivers are required in many power electronics applications. This paper describes an implementation of a digital isolator using discrete components with a planar coreless PCB signal transformer providing the isolation. The use of an electrostatic shield between the transformer windings is shown to provide sufficient common-mode transient immunity to support IGBT half-bridge drivers, an application subject to a severe dV/dt transient during switching. The design is verified through the experimental implementation of a prototype half bridge using two of the proposed discrete digital isolators with SiC power transistors and demonstrates common-mode transient immunity greater than 15 kV/us with very low implementation complexity.

Introduction

Digital isolators are a common requirement in many power electronics applications to galvanically isolate digital control signals from power device gate drivers. A wide range of discrete isolated gate driver topologies using planar transformers have been reported from applications such as fixed frequency 50% duty cycle drivers[1], 8% to 87% duty cycles[2], to more recent complex implementations for wider duty cycles such as 15% to 90% resonant gate drivers[3]. Bidirectional data communications are reported in[4][5], and[6][7][8] supporting both data communications and gate driver power.

A challenging application for these circuits is the high-side driver of a hard switching half-bridge switch topology employing IGBTs, MOSFETs both silicon and SiC-based, or GaN devices. In these applications, the turn-on and turn-off process involves the rapid change in common-mode voltage between the control side and the driver side which can result in significant displacement currents through parasitic capacitances and result in circuit malfunction. This effect is commonly parameterized by a common-mode transient immunity specification (CMTI) that indicates the maximum common-mode voltage rate of change that can be accepted without affecting the data transmission function.

Earlier circuits employing planar transformers[1][2] functioned by providing the gate drive power through the planar transformer, and signalled the device turn-on by providing power and turn-off by removing power. This can limit the range of duty cycles supported, but reduce the concern of CMTI due to the significant energy required to change the switching device’s gate capacitance.

More recent implementations prefer constant driver power and independent data signalling supporting full 0 to 100% duty cycles for modern PWM type applications. These use some type of ferrite core to improve the planar transformer performance[5][8], differential signalling[4][7], and/or an electrostatic shield layer[4][5]. Reported CMTI specifications are in the range of 15 kV/μ\mus to 300 kV/μ\mus. However, all result in a moderate to high level of implementation complexity.

This paper describes a discrete solution employing a coreless planar transformer with an electrostatic shield layer implemented using a 4-layer PCB. The design is validated directly in a high-side gate-driver application and shown to provide a CMTI specification of 15 kV/μ\mus.

The contribution of this work is the demonstration that a practical high-side digital gate drive isolator can be realized using only a coreless PCB transformer, single transistor detector and an embedded electrostatic shield. Unlike many reported planar transformer isolators that rely on ferrite cores, differential signalling, or complex bidirectional communication structures, the proposed approach achieves experimentally verified operation at greater than 15 kV/μ\mus CMTI while maintaining very low circuit and manufacturing complexity.

The paper is structured as follows: section II describes the discrete circuit implementation of the digital isolator showing both the PCB transformer winding and electrostatic shield layout. The detailed test setup used to evaluate the isolator performance is described in section III as well as the CMTI results in both the unshielded and shielded cases using the high-side driver. Section IV shows the operation of the complete half-bridge driver with both low and high-side drivers confirming proper operation. Section V provides a comparison of the proposed implementation with the published literature.

Proposed Isolation Circuits

The proposed discrete digital isolator circuit is shown in Figure 1. The left side is the control side and here is implemented as a class C negative resistance LC oscillator based on a cross coupled MOSFET pair M1M_1 and M2M_2 with an oscillation frequency around 15 MHz. The internal capacitance of the transistor pair is sufficient to ensure oscillation in this case. Alternatively the inductor L1L_1 could be energized with a similar frequency square wave from a modern micro-controller port.

Figure 1. Proposed digital isolator with inter-winding shield

The galvanic isolation functionality is achieved through the use of the coreless PCB transformer, formed by the bottom side inductor L1L_1 with magnetic coupling to the top side inductor L2L_2. Typical PCB materials exhibit dielectric breakdown strengths in excess of 20 kV/mm[9], thus easily providing several kV isolation for the PCB thickness of 1.2 mm used here. Inductor L1L_1 is implemented on one side of the PCB. fig:2a shows the PCB layout of this inductor with a zero ohm surface mount resistor or equivalent used to bridge from the inside to the outside rather than using vias. This allows the full insulation properties of the PCB material to provide the high voltage isolation barrier with sufficient creep distances[10]. The inductor has 8 turns of 200 μ\mum wide copper trace with 200 μ\mum trace separation and the outside dimensions of 15 mm and 18 mm as shown in the figure. Using the expressions in[11] yields an estimated inductance of 1.66 μ\muH, while the measured inductance on the prototype was 1.7 μ\muH.

In fig. 1, the right side is the detector structure. The inductor L2L_2 is identical to that of L1L_1 but is placed on the opposite side of the PCB, but directly overlapping it. Thus L1L_1 and L2L_2 have a significant coupling coefficient and form a signal transformer for this application[12].

Most magnetically coupled isolators use differential detectors and/or differential transformers which result in high complexity circuit implementations. However, the discrete detector used here is one of the simplest possible structures consisting of just the bipolar transistor Q1Q_1 and the resistor R1R_1. The induced voltage in L2L_2 is effectively half-wave rectified by the bipolar transistor Q1Q_1 with resistor R1R_1 allowing a path for the inductor energy to decay rapidly when the control signal and corresponding high frequency oscillation stops. In this circuit the transistor Q1Q_1 is driven into saturation when a positive voltage is induced in L2L_2. This pulls the output signal active low. The saturation recovery time of Q1Q_1 is sufficient to keep the output pulled low during the negative cycle of the voltage induced in L2L_2. This saturation recovery time is typically 100 ns for the bipolar transistor used and effectively provides glitch filtering functionality when the detector output is active low.

fig:2c shows the PCB layout for L2L_2 which has identical dimensions to L1L_1. The resistor R1R_1 and transistor Q1Q_1 can be placed inside the spiral inductor and again zero ohm surface mount resistors or equivalent bridge from the inside to the outside thus avoiding vias to ensure the full PCB material isolation is available.

The measured waveforms for normal operation of this circuit are shown in Figure 3. Figure 3a shows the proper functionality with a 25 kHz input logic signal and the active low output shown. Some small amount of the high frequency energizing signal can be seen to feed through due to the half-wave rectification, but proper logic levels are readily maintained. Figure 3b and Figure 3c show the measured transitions and propagation times demonstrating a turn-on delay time of 148 ns and turn-off delay of 160 ns. These delays are sufficiently small for typical medium frequency power conversion systems employing IGBTs or SiC MOSFETs. The similarity of the turn-on and turn-off delays make the design suitable for PWM based converters to avoid pulse width distortion.

Oscilloscope traces showing functionality, turn-on propagation time, and turn-off propagation time

Figure 3. Functionality of implemented isolator (including shield)

In these type of power electronics systems, a key factor is common-mode transient immunity (CMTI). This is particularly true in the case of the high-side driver in such an application. The source of the transient is illustrated with the fictional voltage source VCMV_{CM} shown in the Figure 1 and the parasitic capacitance between the signal transformer windings represented by CPC_P. For the prototypes, the measured capacitance was 5 pF.

Consider the controller side (left) being at ground potential and the isolated detector side being part of a high-side driver that is turned on. The ’0V’ of the detector will be pulled up to the high voltage level of the application. When the isolator is signalled to turn-off, the ’0V’ of the detector will rapidly transition from its high value of typically several hundred volts to its low value close to ground potential. This transition must happen quickly in hard switched power electronics circuits to minimize switching losses in the power transistors. The transition is equivalent to a fast high voltage falling edge shown as VCMV_{CM} in the schematic. The net effect can be viewed as a rising edge on the left side of CPC_P causing a displacement current flowing into L2L_2, potentially turning back on transistor Q1Q_1. In § 2-A, it is shown that this failure mechanism occurs and limits the CMTI of the circuit. The rising edge case is less problematic due to the inherent holding function provided by the transistor saturation of Q1Q_1 when the isolator output is active low

In order to improve the CMTI of the design, an electrostatic shield is implemented. This is achieved by moving to a 4-layer PCB and using one of the internal layers as the shield. Figure 2b shows the layout of the electrostatic shield. A solid layer would destroy the signal transformer coupling by creating a shorted turn in the magnetic field path. Therefore a small gap of 200 μ\mum is placed on the four diagonals to reduce magnetically induced eddy currents flowing in the shield conductors while minimizing the capacitive coupling between the windings. The presence of the electrostatic shield reduces the magnetic coupling coefficient between the windings. Measurements on prototype planar transformers show a reduction in the magnetic coupling coefficient from 0.45 with no electrostatic shield down to 0.3 with the electrostatic shield shown. Although the electrostatic shield reduces the magnetic coupling coefficient, the remaining coupling is sufficient to ensure reliable operation of the detector transistor. In contrast, the associated reduction

PCB layout of coreless transformer and shield

Figure 2. PCB layout of coreless transformer and shield

in interwinding capacitance significantly improves the CMTI performance of the isolator. The plots in Figure 3 are for the isolator circuit including the electrostatic shield.

Common Mode Transient Immunity Evaluation

The most direct method of evaluating the CMTI in the high-side power switching application is to implement the half-bridge power configuration. Figure 4 shows the test circuit implemented to evaluate the proposed discrete digital isolator. A 4-layer PCB implementing two of the isolation circuits from section II together with power drivers, isolated DC:DC converters and two silicon carbide (SiC) MOSFETs form a half-bridge circuit. SiC MOSFETs (SCTWA90N65G2) are selected due to their fast switching times for the purposes of evaluation. The application of the proposed circuit is intended for the more modest switching times employed in typical IGBT applications. Figure 5 shows a photo of the 4-layer test PCB and the spiral inductors of both the high and low-side isolators can be seen on the left side of the board.

Figure 4. Common mode immunity test circuit using a high-side driver and SiC transistors

Photo of the half-bridge test PCB

Figure 5. Photo of the half-bridge test PCB

To evaluate the performance of the isolator, the low-side is held off and the circuit is used to switch a grounded series inductive and resistive load to the high voltage DC level VDCV_{DC} variable in this setup from 0 V to 400 V DC. The test sequence involves a double pulse high-side test, whereby the high-side is turned on for 19 μ\mus, providing a positive transition from 0 V0\ \mathrm{V} to VDCV_{DC} on the switching node and then charging up the load inductor. At the end of the pulse period the high-side is turned off causing the switching node to rapidly transition to below 0 V0\ \mathrm{V} then turning on the internal diode of the low-side switch. This sequence is then repeated once more.

Correct functioning of the circuit is verified by varying the DC voltage VDCV_{DC} from 0 V0\ \mathrm{V} up to 400 V400\ \mathrm{V} and observing the switching node for proper operation. Note that for this test operation, the ground of the controller side is directly connected to the ground of the high voltage source VDCV_{DC} for testing purposes as this maximizes the common-mode voltage stress on the high-side driver. Figure 6 shows a photo of the complete test bench setup.

Photo of the complete test system

Figure 6. Photo of the complete test system

Measured performance of the unshielded implementation

The performance of the discrete digital isolator with no electrostatic shield was evaluated using the developed test setup. As the applied DC voltage VDCV_{DC} exceeded about 200 V200\ \mathrm{V}, the operation of the circuit was observed to fail.

Figure 7 shows the observed failure mechanism. At the turn-off point of the first pulse, the switching node falls as expected, but this transition which appears as a common-mode transient voltage across the isolator’s signal transformer is now sufficient to cause the isolator’s output to turn back on again in error. The second pulse shows the identical fault occurrence.

Turn-off failure with no shield

Figure 7. Turn-off failure with no shield

Figure 8 shows the high to low transition on the switching node that triggers this fault. The measured turn-off transient shows a fall time rate of change of 6.8 kV/μs6.8\ \mathrm{kV}/\mathrm{\mu s} which is a modest value of CMTI in the context of modern digital isolators.

Falling edge time for turn-off failure

Figure 8. Falling edge time for turn-off failure

Measured performance of the shielded implementation

The performance of the discrete digital isolator with the electrostatic shield included was then evaluated using the developed test setup. In this case, full correct performance was observed over the full applied voltage range. Figure 9 shows the double pulse high-side test with no extraneous switching events present. Figure 10 shows the detailed edge transition. The measured turn-off transient shows a fall time rate of change of over 15 kV/μs15\ \mathrm{kV}/\mathrm{\mu s}.

Turn-off correct with shield at 400 V operation

Figure 9. Turn-off correct with shield at 400 V operation

Falling edge time for correct turn-off

Figure 10. Falling edge time for correct turn-off

Complete half-bridge operation

The half-bridge configuration with both high-side and low-side drivers was then tested for normal bridge operation driving the series inductor and resistor load, but now the other side of the load is connected to half the VDCV_{DC} supply formed from a capacitor divider.

Figure 11 shows the switching node over a sequence of both drivers off, one 19 μs19\,\mu\mathrm{s} pulse high-side on, 2 μs2\,\mu\mathrm{s} dead time, one 19 μs19\,\mu\mathrm{s} pulse low-side on, 2 μs2\,\mu\mathrm{s} dead time, all repeated once and then both drivers off again. The figure shows correct operation of the half-bridge circuit with the 400 V400\,\mathrm{V} DC supply for this complete sequence.

Half bridge with both low and high-side drivers

Figure 11. Half bridge with both low and high-side drivers

Conclusions

This paper describes a discrete digital isolator suitable for use in power electronics applications. The design uses a coreless planar PCB transformer structure with an electrostatic shield implemented using a 4-layer PCB and a single transistor detector structure. Experimental measurements demonstrate a propagation delay below 200 ns200\,\mathrm{ns} and reliable operation in a SiC MOSFET half-bridge power stage. Experimental results demonstrate that the embedded electrostatic shield improves the CMTI from approximately 6.8 kV/μs6.8\,\mathrm{kV}/\mu\mathrm{s} to greater than 15 kV/μs15\,\mathrm{kV}/\mu\mathrm{s}.

Table I shows a comparison of the proposed design with a range of published gate driver implementations using planar transformers. The table shows that while the common-mode transient immunity is at the lower end of the values listed, the complexity is far less than any of the other designs.

Signal/PowerTransformerScreen/ShieldPolarityCMTIComplexity
[1]signal is power 50% duty cycle2-layer PCB corelessnoN/AN/Alow
[2]signal is power 8% to 87% duty cycle2-layer PCB corelessnoN/AN/Alow
[3]signal is power 15%- 90% duty cyclesix two-layer PCB windings with corenoN/A35 kV/µsmoderate
[7]one direction3 stacked 2-layer PCBsnodifferential100 kV/µsmoderate
[8]bidirectional data and power2-layer PCB with ferritenosingle ended100 kV/µsmoderate
[5]bidirectional signal (CAN)4-layer PCB with coreyessingle ended125 kV/µshigh
[4]bidirectional8 layer PCB with coreyesdifferential300 kV/µshigh
[6]bidirectional data and power6 layer PCB with ferrite corenosingle ended15 kV/µsmoderate
this workone direction4-layer PCB corelessyessingle ended15 kV/µsvery low

Table I. Comparison of gate drivers utilizing planar transformers

The use of standard multilayer PCB technology, the absence of magnetic cores and the minimal component count make the approach attractive for low cost isolated gate driver systems and other applications requiring robust digital signal isolation.

References

  1. [1]S. C. Tang, S. Y. Hui and Henry Shu-Hung Chung, "Coreless printed circuit board (PCB) transformers with multiple secondary windings for complementary gate drive circuits," in IEEE Transactions on Power Electronics, vol. 14, no. 3, pp. 431-437, May 1999, doi: 10.1109/63.761686.DOI
  2. [2]S. Y. Hui, Henry Shu-Hung Chung and S. C. Tang, "Coreless printed circuit board (PCB) transformers for power MOSFET/IGBT gate drive circuits," in IEEE Transactions on Power Electronics, vol. 14, no. 3, pp. 422-430, May 1999, doi: 10.1109/63.761685.DOI
  3. [3]Q. Yue, H. Peng, Q. Tong and Y. Kang, "A Novel Isolated Resonant Gate Driver With Adjustable Duty Ratio for SiC MOSFET," in IEEE Journal of Emerging and Selected Topics in Power Electronics, vol. 10, no. 6, pp. 7162-7176, Dec. 2022, doi: 10.1109/JESTPE.2022.3174725.DOI
  4. [4]L. Gouy, A. -S. Bacquet, N. Ginot and C. Batard, "A Gate driver Core Including Bidirectional Communication Using a Single Planar Transformer for High D/dt SiC modules," in IEEE Transactions on Power Electronics, 2026, doi: 10.1109/TPEL.2026.3728854.
  5. [5]C. Bouguet, N. Ginot and C. Batard, "Communication Functions for a Gate Driver Under High Voltage and High dv/dt," in IEEE Transactions on Power Electronics, vol. 33, no. 7, pp. 6137-6146, July 2018, doi: 10.1109/TPEL.2017.2750744.DOI
  6. [6]J. Weckoldt, N. Ginot, C. Batard, T. L. Le and S. Azzopardi, "A Bidirectional Communicating Power Supply Circuit for Smart Gate Driver Boards," in IEEE Transactions on Power Electronics, vol. 35, no. 8, pp. 8540-8549, Aug. 2020, doi: 10.1109/TPEL.2019.2960632.
  7. [7]Z. Guo and H. Li, "A MHz-Pulse-Transformer Isolated Gate Driver With Signal-Power Integrated Transmission for Medium-Voltage SiC MOSFETs," in IEEE Transactions on Power Electronics, vol. 37, no. 8, pp. 9415-9427, Aug. 2022, doi: 10.1109/TPEL.2022.3158145.DOI
  8. [8]S. Song, H. Peng, Q. Tong, R. Min and Y. Kang, "Bidirectional Signal and Power Co-Transmission Techniques in Isolated Gate Driver for SiC MOSFET," in IEEE Transactions on Power Electronics, vol. 40, no. 10, pp. 14447-14458, Oct. 2025, doi: 10.1109/TPEL.2025.3575906.DOI
  9. [9]O. C. Sproat et al., "Optimized Design of Multi-MHz Frequency Isolated Auxiliary Power Supply for Gate Drivers in Medium-Voltage Converters," in IEEE Transactions on Power Electronics, vol. 35, no. 9, pp. 9494-9509, Sept. 2020, doi: 10.1109/TPEL.2020.297277.
  10. [10]SLUP421 — "Demystifying Clearance and Creepage Distance for High-Voltage End Equipment" Available at: https://www.ti.com/lit/pdf/SLUP421 [accessed 21 Mar 2026].
  11. [11]S. S. Mohan, M. del Mar Hershenson, S. P. Boyd and T. H. Lee, "Simple accurate expressions for planar spiral inductances," in IEEE Journal of Solid-State Circuits, vol. 34, no. 10, pp. 1419-1424, Oct. 1999, doi: 10.1109/4.792620DOI
  12. [12]S. C. Tang, S. Y. Hui and H. S. . -H. Chung, "Characterization of coreless printed circuit board (PCB) transformers," in IEEE Transactions on Power Electronics, vol. 15, no. 6, pp. 1275-1282, Nov. 2000, doi: 10.1109/63.892842.DOI

Paper details

vlnc:W_zwkmcf45
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Engineering

Not recorded for this paper

View statement
Looking for related papers…
Contents