WorksPhysics and Astronomy
Impact of iso-structural template layer on stabilizing pyrochlore BiRhO
Abstract
We present an epitaxial stabilization of pyrochlore BiRhO on Y-stabilized ZrO (YSZ) (111) substrate by inserting a pyrochlore EuTiO template layer, otherwise Bi-based layered structures being formed directly on YSZ (111) substrate. This result reveals that "iso-structural crystal phase" plays an important role in the interfacial phase control. The BiRhO film exhibits -type electrical conduction with the lowest longitudinal resistivity () among the reported Rh pyrochlore oxides. Such parameters as , carrier density, and mobility show almost no temperature dependence in the measured range of 2300 K, indicating BiRhO as one of the rare examples of conducting pyrochlore oxides.
Complex metal oxides are intriguing materials platform for exploring exotic physical phenomena related to the mutual interplay between charge, spin, and orbital degrees of freedom [1, 2, 3]. The electron correlation in oxides gives rise to a diverse set of interesting phenomena such as metal–insulator transitions, charge/spin ordering, multi-ferroicity, and high-temperature superconductivity. To push such intriguing physical properties towards practical application, the consistent effort has been devoted to the improvements in the oxide thin-film growth techniques with atomic precision. Among them, perovskite oxides () are one of the most well-studied materials. Various kinds of substrates are commercially available for perovskite oxides to cover a wide range of lattice constants. They are utilized to impose an epitaxial strain for tuning the physical properties. Furthermore, it has been widely recognized that metastable perovskite phase can be often epitaxially stabilized on perovskite substrates. Several studies, with pulsed laser deposition (PLD), have reported that such metastable perovskite phases can be grown even from targets with different phases, as exemplified by SrMoO [4], EuMoO [5], SrNbO [6], EuNbO [7], SrTaO [8], and PbRuO [9]. These results imply that iso-structural interface plays important roles to stabilize certain crystal phases as epitaxial thin films.
In contrast to perovskite oxides, the situation is different in another typical complex oxide, namely, pyrochlore oxides (). There is no commercialized substrate available for pyrochlore oxides. As an alternative, Y-stabilized ZrO (YSZ) has been widely employed. This is because a pyrochlore can be viewed as a superstructure of a fluorite with ordered and cation sites and oxygen vacancy on 1/8 sites. Moreover, twice the lattice constant of YSZ () is in good lattice matching with those of typical transition metal pyrochlore oxides. With making use of this structural compatibility, there have been numbers of reports on epitaxial growth of pyrochlore oxide thin films on YSZ substrates [10, 11, 12, 13]. However, this is not the case for Bi-Rh-O system. Pyrochlore BiRhO phase is a thermodynamically stable phase and can be synthesized by a solid state reaction in ambient pressure under O flow [14, 15, 16]. Nonetheless, even with using BiRhO as a target for PLD, a layered compound BiRhO phase appears under as-grown conditions on YSZ substrates [17]. To avoid the formation of this phase, we have attempted an ex-situ annealing of amorphous precursor Bi-Rh-O films deposited by PLD at room temperature. Still, so-called Bi-based layered supercell phases [BiO]-[RhO] () have been stabilized as the film form (Figure 1) [18]. These results drive us to pursue the missing link between YSZ and pyrochlore .

Figure 1. The schematic relationship between the substrate and the stabilized phase in Bi-Rh-O system. Crystal structure of () is from ref. [18].
In this study, we report the effect of a template layer with iso-structural pyrochlore on stabilizing pyrochlore phase. We chose pyrochlore as the template layer because it is a stable phase and can be epitaxially grown on YSZ. We find that the insertion of the template layer can stabilize the pyrochlore phase even by annealing the amorphous precursor Bi-Rh-O films. Thus prepared epitaxial films indicate lower resistivity than the previously reported bulk polycrystalline , ensuring high crystallinity of the obtained film. These results suggest that this technique can be useful for the preparation of other transition metal pyrochlore oxides.
Epitaxial (111) thin films were grown on template layer / YSZ (111) substrates by pulsed laser deposition (PLD) and subsequent annealing (Also see Figure S1 and Figure S1 in Supplementary Materials). Before the film growth, YSZ (111) substrates were annealed in air with a furnace at 1,350 °C for 3 h to obtain a clear step-terrace structure with single-unit-cell height ( Å). PLD target of was prepared by mixing and powders at a molar ratio of Bi:Rh =1:1, pelletizing and sintering it at 950 °C for 24 h in a tube furnace under flow (200 mL/min.) [14, 15, 16]. Target of was also prepared by a solid state reaction [19]. A mixture of and powders at a molar ratio of Eu:Ti =1:1 were grounded and annealed at 1,300 °C for 24 h in air. After this first step, the powders were re-grounded, and then pelletized and sintered at 1,300 °C for 24 h in air. KrF excimer laser pulses ( nm) were employed to ablate the targets. The template layer was deposited at 900 °C under Torr by laser pulses at a frequency of 5 Hz and an energy fluence of 0.9 J/cm. The sample was then cooled down to room temperature, and amorphous precursor Bi-Rh-O layer was deposited in-situ under Torr by laser pulses at a frequency of 5 Hz and an energy fluence of 1.1 J/cm. layer was crystallized by annealing the sample at 1,000 °C for 1 h in a tube furnace under flow (200 mL/min.). Structural properties of the films were characterized by x-ray diffraction (XRD) (SmartLab, Rigaku) and cross-sectional transmission electron

Figure S1. Temperature () and oxygen pressure () conditions for (a) PLD growth and (b) furnace annealing processes. (c) A schematic of (BRO/ETO) heterostructure. Rocking curve around the (d) (444) and (e) (444) peaks. (f) Azimuthal () scan around (662) (top), (662) (middle) and YSZ (331) (bottom) peaks.
microscopy at room temperature. The magnetotransport properties were measured with using a cryostat equipped with a 9 T superconducting magnet (PPMS, Quantum Design Co.), where magnetic field () was applied perpendicular to the film surface.
We first discuss the structural properties of (25 nm)/ (30 nm)/YSZ (111) sample as summarized in Figure 2. Figure 2(a) and (Figure 2b) show XRD - scan of the film. Even in the wide scan range of 0–120°, only the peaks from (111) orientated pyrochlore phase are observed without any impurity peaks. The (444) peaks of and are clearly separated as can be seen in Figure 2(b). The full width at half maximum (FWHM) of the rocking curves around (444) peaks of (Figure S1) and (Figure S1) are about 0.07°, evidencing the high crystallinity of the film. Reciprocal space mapping (RSM) around YSZ (331) peak is shown in Figure 2(c). In-plane lattice constants of and match with that of YSZ substrate, indicating that both of the layers are coherently grown on the substrate under tensile strain. Azimuthal () scan around (662) and (662) show the three-fold symmetry, which is the same as that of YSZ (331), indicating that our films do not contain in-plane mis-oriented domains (Figure S1).

Figure 2. (Color online). (a) X-ray diffraction (XRD) - scan for a (BRO) thin film grown on (ETO) / YSZ (111) substrate, and (b) magnified view around (444) peak. Peaks from YSZ substrate are marked with asterisks in (a) and (b). (c) XRD reciprocal space mapping around YSZ(331) peak. The broken line indicates the relaxation condition where a fully relaxed cubic film peak is supposed to be located. (d) High resolution high-angle annular dark-field (HAADF) scanning transmission electron microscopy (STEM) image of the film. (e) Wide-range cross-sectional HAADF-STEM image. The corresponding energy dispersive x-ray (EDX) spectrometry maps for (f) Bi L, (g) Rh L, (h) Eu L, (i) Ti K, and (j) Zr L edges, respectively.
The formation of the designed epitaxial heterostructure (Figure S1) is also confirmed by the cross-sectional high-angle annular dark-field (HAADF) scanning transmission electron microscopy (STEM) image taken along the azimuth of the YSZ substrate as shown in Figure 2(d). Energy dispersive x-ray spectrometry (EDX) maps for the film in a wider region (shown in Figure 2(e)) are also given in Figure 2(f)–Figure 2(j), verifying fairly sharp interface between and layers, despite of the solid phase epitaxy technique.
Through the structural characterizations, it is evident that pyrochlore is formed on the template layer on YSZ (111) substrate. To demonstrate the effect of template layer, XRD data are shown in Figure S2 for the films synthesized under various annealing temperature () with or without the template layer. Without the template layer, Bi-based layered supercell phases () are formed depending on : for °C and for °C. At °C, only is formed. On the other hand, with the template layer, phase appears at °C. Note that all the films are deposited from the same target under the same conditions. These results clearly indicate that we can control the crystal phase of thin films by inserting an appropriate template layer on substrates.

Figure S2. XRD - scans for Bi-Rh oxide films on (a) YSZ substrate and (b) template layer after annealing at 1,000, 900, and 700 . Peaks from YSZ substrate, template, , (), and are marked with asterisks, arrows, circles, triangles, squares, and diamonds, respectively.
We next discuss the magnetotransport properties of the film. Figure 3(a) shows the temperature dependence of longitudinal resistivity () for the BiRhO film and previously reported polycrystalline bulk samples of BiRhO [14], SmRhO [20], and LuRhO [21]. The BiRhO film shows lowest among the reported Rh pyrochlore oxides in the entire measured temperature range. This can be ascribed to the reduction of the scattering from grain boundaries compared with the polycrystalline bulk samples. Although BiRhO film shows of mcm and is electrically conducting, it does not show a strong temperature dependence in . Thus, the electrical properties of BiRhO
Figure 3. Temperature dependence of longitudinal resistivity () for BiRhO thin film (present study) and previously reported polycrystalline bulk samples of BiRhO [14], SmRhO [20], and LuRhO [21]. Data are available only at 77 and 300 K for [14] and at 300 K for [20]. Temperature dependence of for BiRhO thin film under magnetic fields below 50 K. Note that is displayed in (a) logarithmic and (b) linear scales. Magnetic field () dependence of (c) magnetoresistance ratio (MRR )) and (d) Hall resistivity () at various temperatures. Hall resistivity at 100 K is given with an vertical offset by 10 ncm. Similar results are obtained in the intermediate temperature range.
are like those of dirty metals. In Figure 3(b), we compare the temperature dependence of for BiRhO thin film below 50 K under or 9 T, where shows a slight upturn below K in both cases. Figure 3(c) and Figure 3(d) present magnetoresistance (MR) ratio () and Hall resistivity () measured at various temperatures, respectively. BiRhO film exhibits a weak positive MR, the magnitude of which increases up to 1.5% at 2 K with lowering temperature. MR is quadratic at higher temperatures and turns into rather linear at lower temperatures. Together with the temperature dependence in Figure 3(b), BiRhO film seems to have a localized nature at lower temperatures. In all measured temperature ranges, is linear to with a positive slope, indicating a -type carrier conduction. The carrier density and mobility are estimated as cm and 0.1 cm/Vs by single-carrier fitting at 2 K, both of which show almost no temperature dependence.
In conclusion, we have fabricated pyrochlore BiRhO thin films on EuTiO / YSZ (111) substrates starting from amorphous precursor Bi-Rh-O layers. We clarify that pyrochlore phase can be stabilized with the EuTiO template layer whereas Bi-based layered supercell structures are formed without it. Our BiRhO film exhibits -type electrical conduction with the lowest among the reported pyrochlore Rh oxides, being important component for the study on the pyrochlore heterostructures. These results demonstrate the critical role of the interface-engineering in determining crystal structures, which will pave the way for further materials design of transition metal oxides.
Supplementary Material
See supplementary material for the additional XRD measurements data and the fabrication procedure.
Acknowledgments
This work was supported by JSPS Grants-in-Aid for Scientific Research (S) No. JP22H04958, by JSPS Grant-in-Aid for Early-Career Scientists No. JP20K15168, by JSPS Fellowship No. JP22J12905, and by The Murata Science Foundation, Mizuho Foundation for the Promotion of Sciences, Iketani Science and Technology Foundation, Kazuchika Okura. Memorial Foundation, Yazaki Memorial Foundation for Science and Technology, and Mitsubishi Foundation.
References
Supplementary Materials for Impact of iso-structural template layer on stabilizing pyrochlore
M. Ohno; T. C. Fujita; M. Kawasaki
Structural characterization
Effect of iso-structural template layer on stabilizing pyrochlore
II Effect of template layer
References
- [1]H. Y. Hwang, Y. Iwasa, M. Kawasaki, B. Keimer, N. Nagaosa, and Y. Tokura, Nat. Mater. 11, 103 (2012).
- [2]Z. Huang, Ariando, X. Renshaw Wang, A. Rusydi, J. Chen, H. Yang, and T. Venkatesan, Adv. Mater. 30, 1802439 (2018).
- [3]P. Yu, W. Luo, D. Yi, J. X. Zhang, M. D. Rossell, C.-H. Yang, L. You, G. Singh-Bhalla, S. Y. Yang, Q. He, Q. M. Ramasse, R. Erni, L. W. Martin, Y. H. Chu, S. T. Pantelides, S. J. Pennycook, and R. Ramesh, Proc. Natl. Acad. Sci. U.S.A. 109, 9710 (2012).
- [4]A. Radetinac, K. S. Takahashi, L. Alff, M. Kawasaki, and Y. Tokura, Appl. Phys. Express 3, 073003 (2010).
- [5]Y. Kozuka, H. Seki, T. C. Fujita, S. Chakraverty, K. Yoshimatsu, H. Kumigashira, M. Oshima, M. S. Bahramy, R. Arita, and M. Kawasaki, Chem. Mater. 24, 3746 (2012).
- [6]D. Oka, Y. Hirose, S. Nakao, T. Fukumura, and T. Hasegawa, Phys. Rev. B 92, 205102 (2015).
- [7]T. Maruyama, A. Chikamatsu, T. Onozuka, and T. Hasegawa, Appl. Phys. Lett. 113, 032401 (2018).
- [8]J. Zhang, Y.-Y. Pai, J. Lapano, A. R. Mazza, H. N. Lee, R. G. Moore, B. J. Lawrie, T. Z. Ward, G. Eres, V. R. Cooper, and M. Brahlek, Small Science 2, 2100087 (2022).
- [9]T. C. Fujita, L. F. Zhang, and M. Kawasaki, Phys. Rev. Mater. 4, 031401(R) (2020).
- [10]J. Nishimura, T. Fukumura, M. Ohtani, Y. Taguchi, M. Kawasaki, I. Ohkubo, H. Koinuma, H. Ohguchi, K. Ono, M. Oshima, and Y. Tokura, Appl. Phys. Lett. 82, 1571 (2003).
- [11]L. Bovo, X. Moya, D. Prabhakaran, Y.-A. Soh, A. T. Boothroyd, N. D. Mathur, G. Aeppli, and S. T. Bramwell, Nat. Commun. 5, 3439 (2014).
- [12]T. C. Fujita, Y. Kozuka, M. Uchida, A. Tsukazaki, T. Arima, and M. Kawasaki, Sci. Rep. 5, 9711 (2015).
- [13]H. Ito, T. C. Fujita, and M. Kawasaki, APL Mater. 9, 101116 (2021).
- [14]J. M. Longo, P. M. Raccah, J. A. Kafalas, and J. W. Pierce, Mater. Res. Bull. 7, 137 (1972).
- [15]B. J. Kennedy, Mater. Res. Bull. 32, 479 (1997).
- [16]X. Li, Q. Q. Liu, W. Han, Y. Liu, X. D. Li, Y. C. Li, J. Liu, and C. Q. Jin, Int. J. Mod. Phys. B 27, 1362021 (2013).
- [17]M. Uchida, K. Ohba, Y. Ohuchi, Y. Kozuka, and M. Kawasaki, Chem. Mater. 28, 1165 (2016).
- [18]M. Ohno, T. C. Fujita, Y. Masutake, H. Kumigashira, and M. Kawasaki, arXiv:2302.13538 (2023).DOI
- [19]A. Bayart, J.-F. Blach, M. Huvé, F. Blanchard, P. Roussel, R. Desfeux, and S. Saitzek, Opt. Mater. 92, 303 (2019).
- [20]V. Lazarev and I. Shaplygin, Zhurnal Neorganicheskoj Khimii 23, 291 (1978).
- [21]A. M. Hallas, A. Z. Sharma, C. Mauws, Q. Chen, H. D. Zhou, C. Ding, Z. Gong, M. Tachibana, P. M. Sarte, J. P. Attfield, G. M. Luke, and C. R. Wiebe, npj Quantum Mater. 4, 9 (2019).
