WorksPhysics and Astronomy
Beta-Ga2O3 Sub-Micron FinFETs with Si Delta-Doped Channel Modulating Charge Density Above 3x10^13 cm^-2
Abstract
This letter reports on the design and demonstration of high-performance Beta-Ga2O3 FinFETs utilizing MOCVD-grown Si delta-doped channels to achieve enhanced carrier transport and electrostatic control. A record high sheet charge density of 3.3x10^13 cm^-2 was modulated using 100 nm fin channels, delivering a peak drain current of 410 mA/mm and a peak transconductance of 60 mS/mm. The FinFET architecture enables strong gate modulation, achieving a high Ion/Ioff ratio between 10^8 and 10^9. A low contact resistance of 0.42 ohm.mm was achieved to the Si delta-doped channel using MOCVD contact regrowth. Small-signal RF characterization revealed a current-gain cutoff frequency (fT) of 3.8 GHz and a maximum oscillation frequency (fMAX) of 2.1 GHz for a 0.8-micrometer gate length. These results demonstrate the efficacy of combining precision delta-doping with a 3D FinFET geometry for high-frequency Beta-Ga2O3 electronics, establishing a platform for future RF and high-power applications
Introduction
Beta gallium oxide (-GaO) has gained significant attention as an ultra-wide bandgap semiconductor due to its large band gap (4.8 eV), high breakdown field strength (8 MV/cm), and favorable transport properties (=200 cm/V-s, =1.5-2 cm/s)[1], [2], [3]. These characteristics give -GaO a Johnson’s Figure of Merit () that is 2-3X higher than that of GaN, showcasing the promise of this material platform for RF and mm-wave electronics[4]. -GaO RF transistors have shown rapid advancements over the past decade. Early MOSFETs achieved modest frequencies (=3.3 GHz, =12.9 GHz) using recessed gates and heavily doped contacts [5]. Significant improvement emerged with delta-doped channels, increasing to 27 GHz using 120 nm T-gates [6]. By using modulation-doped heterostructures, researchers demonstrated enhancement-mode HFETs reaching even higher frequencies (=30 GHz, =37 GHz), marking a critical breakthrough for -GaO RF transistors [7].
More recently, thin-channel MOSFETs with optimized T-gates and surface passivation achieved remarkable values (48 GHz) while maintaining high breakdown voltages (192 V) [8]. Furthermore, integration of -GaO onto SiC substrates have enabled unprecedented output power (2.3 W/mm at 2 GHz) and pushed up to 57 GHz [9].

Figure 1. a) Schematic of -GaO delta-doped FinFET and MOCVD grown epitaxial layer structure with delta-doped channel b) SEM Image showing the fabricated FinFET device c) SEM Image showing fins with 100 nm width and 200 nm spacing.
For high performance RF devices, it is critical to use vertically scaled channels due to the requirement of scaled gate lengths. -(AlGa)O/GaO modulation doped heterostructures are effective in this respect, however these structures are currently limited to low 2DEG densities ( cm) in -GaO and are not optimal for high power density RF devices. Si delta doped channels are an attractive option since they offer the ability to tune and increase the channel charge density () [6], [10]. Furthermore, delta-doping, with its highly localized doping profile, enhances carrier transport properties by reducing ionized impurity scattering achieving room temperature mobilities exceeding 100 cm/V-s [10], [11], [12], [13]. Prior reports have demonstrated Si delta-doped lateral FETs with high ON-current densities, high unity current gain cut-off frequencies, and notable breakdown characteristics [14]. However, to achieve the full potential of -GaO, it is critical to increase the channel charge density. This enables achieving lower contact resistance, lower access region resistance and higher drain current densities. Furthermore, a Fin Field Effect Transistor design (FinFET) [15], [16], [17], [18] offers superior electrostatic control through the multi-
This work is supported by the Army Research Office UWBG RF center under award No. W911NF2520005 and partly by the National Science Foundation under Grant No. NSF ECCS 2336397. Use of the core facilities at ASU is supported, in part, by NSF award ECCS-2025490.
Nabasindhu Das, Ankita Kashyap, Advait Gilankar, Trevor Thornton and Nidhin Kurian Kalarickal are with School of Electrical, Computer and Energy Engineering, Arizona State University, AZ, USA. Cameron Gorsak, Pushpanshu Tripathi Salil A Paranjape and Hari Nair are with Department of Materials Science and Engineering, Cornell University, NY, USA. gate, three-dimensional geometry, enabling effective modulation of high channels, and significantly reducing short-channel effects like drain-induced barrier lowering (DIBL), subthreshold swing degradation, and leakage currents. Additionally, the FinFET configuration could also lead to improved thermal management due to its inherently larger surface-to-volume ratio, which could be critical for β-Ga₂O₃.
In this work, we report the demonstration of MOCVD grown β-Ga₂O₃ delta-doped FETs with 100 nm fin channels modulating a record-high channel charge density of cm, along with an on/off ratio between -. The work highlights the combined advantages of high quality MOCVD Si delta-doped channels with superior device geometries, to collectively push the boundaries of β-Ga₂O₃-based electronics, paving the way for enhanced performance and broader applicability in future high-power and RF electronic systems.
Device Growth & Fabrication
The δ-doped epitaxial structure (Figure 1(a)) used in this work was grown by MOCVD in an Agnitron Agilis 100 system. First, ~50 nm of UID β-Ga₂O₃ was grown at 600°C, 15 Torr using Ar carrier gas and Triethylgallium (TEGa) and O₂ as precursors to trap the residual Fe tail [19] followed by a ~300 nm UID buffer. For the δ-doped layer, the sample was dosed with ~20 nmol of silane post a TEGa purge followed by a final cap layer of ~30 nm of UID β-Ga₂O₃. An ohmic contact regrowth process was used to achieve low contact resistance. The source and drain regions were first patterned with a thick PECVD grown SiO₂ hard mask. Post patterning, the β-Ga₂O₃ epilayer was etched to a depth of 60 nm and regrown with heavily doped n-type β-Ga₂O₃ with doping concentration of cm to achieve low contact resistance [6]. Fin structures (100 nm width (), 200 nm spacing ()) were defined using e-beam lithography and then etched to 100 nm depth using a low power BCl₃ based ICP-RIE process to minimize sidewall etch damage to the δ-doped channel. A bilayer composite mask consisting of 10 nm SiO₂ and ZEP 520A ebeam resist was used to carry out the fin etch process. After defining the fins, 200 nm mesa etch was performed for device isolation. To reduce gate leakage, 7 nm thick Al₂O₃ was deposited via plasma assisted ALD as the gate dielectric. The Al₂O₃ over the ohmic regions was selectively removed using BCl₃ etching for source/drain metallization. A Ti/Au (40nm/60nm) stack was then deposited via e-beam evaporation followed by short RTA
anneal (470°C, 1 min, N₂ ambient) to form the ohmic contacts. Finally, a 100 nm Schottky Ni gate was deposited using e-beam evaporation with 180-degree sample rotation for even deposition on the gate sidewall. The fabricated device is imaged using scanning electron microscope and shown in Figure 1(b) and 1(c).
Results & Discussion
Capacitance-voltage (CV) measurements were carried out using an Agilent B1500 parameter analyzer at a frequency of 100 kHz (Figure 2(a)) on planar MOS structures (see inset of Figure 2(a)). The carrier density profile extracted (Figure 2(b)) shows a narrow doping distribution with an integrated sheet charge density of cm and full width half maximum (FWHM) of 8.2 nm. Hall measurements revealed a δ-doped sheet carrier density of cm with Hall mobility of 89 cm²/Vs at room temperature. The discrepancy between CV and Hall may be attributed partly to the leakage in the MOS structures for voltages exceeding -10 V. Contact Resistance of 0.42 Ω-mm and a sheet resistance of 2.04 kΩ/□ were measured using transfer length measurements (TLM) (Figure 3(a)). The sheet resistance extracted from TLM measurements matches closely to that estimated using Hall (2.1 kΩ/□).

Figure 2. a) Capacitance-Voltage profile inset delta-doped planar MOSCAP b) Electron concentration profile extracted from CV measurements.

Figure 3. a) TLM measurements showing sheet resistance and total contact resistance. b) Output IV characteristics, c) transfer IV characteristics and d) Log-scale transfer IV characteristics of delta-doped FinFET.
Figure 3(b) shows the representative DC output characteristics of the delta doped FinFET with a gate length of 0.8 μm. A maximum drain current of 410 mA/mm was measured at =1 V and =10 V, which is the highest reported for β-Ga₂O₃ FinFETs. The drain current is normalized to the effective device width which in this case is 33% of the total width (=100 nm, =200 nm). The on-resistance of the device is measured to be 10.1 Ω.mm. A maximum transconductance () of 60 mS/mm was measured at gate bias of 0 V (Figure 3(c)). The transconductance shows an increase after an initial peak at -4 V which suggests the possibility of fixed interface charges at the Al₂O₃/Ga₂O₃ interface leading to the formation of an accumulation channel. A pinch off voltage of -8.3 V was estimated by linear extrapolation of transfer I-V which is much lower than that obtained on planar MOS structures ( -15 V, inset of Figure 3(a)). The lowered V is attributed to the sidewall depletion in the case of FinFET which is absent in the planar devices. The measured FinFETs also display a high I/I ratio between - even with n cm (Figure 3(d)), showing the effectiveness of the FinFET design.
The high frequency small-signal performance was characterized between 0.1 GHz and 25 GHz using an vector network analyzer. Figure 4(a) shows the measured post de-embedded short-circuit current gain (h21) & unilateral power gain (U). Peak current gain cut-off frequency (f) of 3.8 GHz and associated peak maximum oscillation frequency (f) of 2.1 GHz were measured at gate bias of -4 V and drain bias of 10 V. The lower f is likely due to large gate resistance due from the use of thin (100 nm) Ni gates, which is more resistive compared to Au. The dependence of the cutoff frequency on gate bias (shown in Figure 4(b)) follows a similar trend to that of the g, peaking at -4 V, however f does not follow the increase in g observed above -3 V. The three terminal breakdown performance of the FinFETs were measured till 200 V (see Figure 4(c)). The leakage current from all the three terminals remained well below nominal breakdown condition (0.1 mA/mm) demonstrating high voltage performance of these devices even with n cm. Figure 4(d) compares the I/I ratio and sheet charge density (n) of various reported β-Ga₂O₃-based field-effect transistors (FETs), serving as a benchmark for evaluating the performance of our device [20, 21, 22, 23]. Positioned toward the upper right region of the plot, our device demonstrates a competitive I/I ratio indicating great FET operation along with high channel charge modulation. This performance underscores the effectiveness of our design and fabrication strategy in pushing the limits of power device operation in the ultra-wide bandgap regime.
Figure 4. a) Measured small signal characteristics of 0.8 μm gate length delta-doped FinFET b) Measured cutoff frequency f as a function of gate voltage measured at 10 V drain bias c) Three terminal breakdown characteristics showing breakdown voltage >200 V d) Benchmarking plot comparing n and I/I ratio of β-Ga₂O₃ FETs.
Conclusion
In conclusion, we have demonstrated MOCVD-grown β-Ga₂O₃ Si delta-doped FinFETs, modulating a record high channel charge density of 3.310 cm along with a high on/off ratio of 10-10. Using a 100 nm fin width and a high charge density Si delta-doped channel, the devices exhibit record high performance including drain current density of 410 mA/mm, transconductance of 60 mS/mm, breakdown voltage exceeding 200V and current gain cut off frequency of 3.8 GHz. The DC and RF performance of these FinFETs can be further enhanced by scaling the gate length.
References
- [1]A. Kumar, K. Ghosh, and U. Singisetti, “Low field transport calculation of 2-dimensional electron gas in β-(AlxGa1−x)2O3/Ga2O3 heterostructures,” J. Appl. Phys., vol. 128, no. 10, Sep. 2020, doi: 10.1063/5.0008578.DOI
- [2]“Low-field and high-field transport in β-Ga2O3,” in Gallium Oxide, Elsevier, 2019, pp. 149–168. doi: 10.1016/b978-0-12-814521-0.00007-5.
- [3]Z. Xie, C.-K. Tan, and M.-C. Cheng, “High-field electron transport properties of β-Ga2O3: An integrated Monte Carlo and first-principles approach,” Appl. Phys. Lett., vol. 126, no. 21, May 2025, doi: 10.1063/5.0271859.DOI
- [4]E. Johnson, “Physical limitations on frequency and power parameters of transistors,” in IRE International Convention Record, New York, NY, USA: Institute of Electrical and Electronics Engineers, pp. 27–34. doi: 10.1109/irecon.1965.1147520.
- [5]A. J. Green et al., “$\beta$ -Ga2O3 MOSFETs for Radio Frequency Operation,” IEEE Electron Device Lett., vol. 38, no. 6, pp. 790–793, Jun. 2017, doi: 10.1109/LED.2017.2694805.
- [6]Z. Xia et al., “Delta Doped $\beta$ -Ga2O3 Field Effect Transistors With Regrown Ohmic Contacts,” IEEE Electron Device Lett., vol. 39, no. 4, pp. 568–571, Apr. 2018, doi: 10.1109/LED.2018.2805785.
- [7]A. Vaidya, C. N. Saha, and U. Singisetti, “Enhancement Mode β-(AlxGa1-x)2O3/Ga2O3 Heterostructure FET (HFET) With High Transconductance and Cutoff Frequency,” IEEE Electron Device Lett., vol. 42, no. 10, pp. 1444–1447, Oct. 2021, doi: 10.1109/led.2021.3104256.
- [8]C. N. Saha et al., “Scaled β-Ga2O3 thin channel MOSFET with 5.4 MV/cm average breakdown field and near 50 GHz fMAX,” Appl. Phys. Lett., vol. 122, no. 18, May 2023, doi: 10.1063/5.0149062.
- [9]M. Zhou et al., “1.1 A/mm β-Ga₂O₃-on-SiC RF MOSFETs with 2.3 W/mm Pₒᵤₜ and 30% PAE at 2 GHz and fₜ/fₘₐₓ of 27.6/57 GHz,” in 2023 International Electron Devices Meeting (IEDM), San Francisco, CA, USA: IEEE, Dec. 2023, pp. 1–4. doi: 10.1109/iedm45741.2023.10413782.DOI
- [10]S. Krishnamoorthy, Z. Xia, S. Bajaj, M. Brenner, and S. Rajan, “Delta-doped β-gallium oxide field-effect transistor,” Appl. Phys. Express, vol. 10, no. 5, p. 051102, May 2017, doi: 10.7567/APEX.10.051102.DOI
- [11]C. Joishi et al., “Deep-Recessed β-Ga₂O₃ Delta-Doped Field-Effect Transistors With In Situ Epitaxial Passivation,” IEEE Trans. Electron Devices, vol. 67, no. 11, pp. 4813–4819, Nov. 2020, doi: 10.1109/TED.2020.3023679.DOI
- [12]N. Kumar, C. Joishi, Z. Xia, S. Rajan, and S. Kumar, “Electrothermal Characteristics of Delta-Doped β-Ga₂O₃ Metal–Semiconductor Field-Effect Transistors,” IEEE Trans. Electron Devices, vol. 66, no. 12, pp. 5360–5366, Dec. 2019, doi: 10.1109/TED.2019.2944628.DOI
- [13]P. Ranga et al., “Delta-doped β-Ga₂O₃ thin films and β-(Al₀.₂₆Ga₀.₇₄)₂O₃ / β-Ga₂O₃ heterostructures grown by metalorganic vapor-phase epitaxy,” Appl. Phys. Express, vol. 13, no. 4, p. 045501, Apr. 2020, doi: 10.35848/1882-0786/ab7712.DOI
- [14]Z. Xia et al., “β-Ga₂O₃ Delta-Doped Field-Effect Transistors With Current Gain Cutoff Frequency of 27 GHz,” IEEE Electron Device Lett., vol. 40, no. 7, pp. 1052–1055, Jul. 2019, doi: 10.1109/LED.2019.2920366.DOI
- [15]G. Amarnath, D. Krishna, and A. Vinod, “TCAD-based Comparative Study of Gallium-Oxide based FinFET and MOSFET,” in 2020 IEEE International Conference on Advent Trends in Multidisciplinary Research and Innovation (ICATMRI), Budlhana, India: IEEE, Dec. 2020, pp. 1–4. doi: 10.1109/ICATMRI51801.2020.9398440.DOI
- [16]K. D. Chabak et al., “Enhancement-mode Ga₂O₃ wrap-gate fin field-effect transistors on native (100) β-Ga₂O₃ substrate with high breakdown voltage,” Appl. Phys. Lett., vol. 109, no. 21, p. 213501, Nov. 2016, doi: 10.1063/1.4967931.DOI
- [17]H. Ebrahimi-Darikhaneh, L. Fernandez-Izquierdo, J. Arellano-Jimenez, M. Quevedo-Lopez, and S. K. Banerjee, “Fabrication and Characterization of Ga₂O₃ FinFETs on Patterned Silicon Substrate,” Adv. Electron. Mater., p. 24000945, Apr. 2025, doi: 10.1002/aelm.202400945.
- [18]Y. Wei et al., “Low Reverse Conduction Loss β-Ga₂O₃ Vertical FinFET With an Integrated Fin Diode,” IEEE Trans. Electron Devices, vol. 70, no. 7, pp. 3454–3461, Jul. 2023, doi: 10.1109/TED.2023.3274499.DOI
- [19]J. P. McCandless et al., “Accumulation and removal of Si impurities on β-Ga₂O₃ arising from ambient air exposure,” Appl. Phys. Lett., vol. 124, no. 11, p. 111601, Mar. 2024, doi: 10.1063/5.0191280.DOI
- [20]N. K. Kalarickal et al., “Demonstration of self-aligned β-Ga₂O₃ δ-doped MOSFETs with current density >550 mA/mm,” Appl. Phys. Lett., vol. 122, no. 11, Mar. 2023, doi: 10.1063/5.0131996.DOI
- [21]M. H. Wong, K. Sasaki, A. Kuramata, S. Yamakoshi, and M. Higashiwaki, “Field-Plated Ga₂O₃ MOSFETs With a Breakdown Voltage of Over 750 V,” IEEE Electron Device Lett., vol. 37, no. 2, pp. 212–215, Feb. 2016, doi: 10.1109/LED.2015.2512279.DOI
- [22]H. Murakami et al., “Homoepitaxial growth of β-Ga₂O₃ layers by halide vapor phase epitaxy,” Appl. Phys. Express, vol. 8, no. 1, p. 015503, Jan. 2015, doi: 10.7567/apex.8.015503.DOI
- [23]M. Higashiwaki et al., “Depletion-mode Ga₂O₃ metal-oxide-semiconductor field-effect transistors on β-Ga₂O₃ (010) substrates and temperature dependence of their device characteristics,” Appl. Phys. Lett., vol. 103, no. 12, Sep. 2013, doi: 10.1063/1.4821858.DOI
