WorksPhysics and Astronomy
Regulating nanoscale heat transfer with Janus nanoparticles
Abstract
Janus nanoparticles (JNPs) with heterogeneous compositions or interfacial properties can exhibit directional heating upon external excitation, such as laser radiation and magnetic field. This directional heating may be harnessed for new nanotechnology and biomedical applications. Understanding thermal transport and temperature control with JNP heating is critical for these advances. Here, we developed a numerical framework to analyze the asymmetric thermal transport in JNP heating under photothermal stimulation. We found that JNP-induced temperature contrast, defined as the ratio of temperature increase in the surrounding water, shows a substantial size and polar angle dependence. Notably, we discovered a significant enhancement of the temperature contrast under pulsed heating due to thermal confinement, compared with the continuous heating. This work brings new insights into the thermal responses of JNP heating and advances the field.
Main context:
Introduction
In the past decade, remarkable advances have been made with the development of nanoparticle heating,[1] [2, 3, 4] including cancer treatment,5-9 neuron modulation,10, 11 molecular hyperthermia,12-14 point-of-care diagnostic,15 imaging enhancement,16-18 energy harvesting,19, 20 and catalysis.21-23 Janus nanoparticles (JNPs) have recently brought new opportunities to the field.24, 25 JNPs are novel nanostructures consisting of heterogeneous structures and materials, including combinations of metallic and non-metallic materials.26-28 The asymmetric coating on JNPs can lead to heterogeneous interfacial properties, as an example, hydrophobic versus hydrophilic with high versus low interfacial thermal resistances (ITRs), respectively.29 This heterogeneity of interfacial properties can be used to regulate the thermal transport around the JNP and lead to directional heating.30, 31 The directional heating has enabled novel applications with JNPs, such as thermophoretic nanomotor,31-33 nano tweezer,34, 35 Janus nano pen injection,36 and energy management.37
The central issue for JNP heating is a better understanding of thermal transport.35 Olarte-Plata et al. analyzed the directional heating of JNPs with heterogeneous coating and ITRs using molecular dynamic simulation and demonstrated a temperature difference (~10K) with octanethiolate/mercaptohexanol-coated JNPs.30 Besides this modeling work, Xuan et al. have developed a self-driven thermophoretic nanomotor with continuous JNP heating. They have shown the speed of the nanomotor can reach ~ with a laser intensity of .33 While these studies have greatly advanced our understanding of directional heating with JNP and demonstrated promising applications, it remains unclear how heterogeneous interface properties of JNP and laser excitation (continuous vs pulsed) contribute to regulating the nanoscale thermal transport.
In this work, we developed a finite difference model to elucidate how the heterogeneous interface properties and laser excitation method regulate the nanoscale heat transfer (Figure 1A). we defined a dimensionless parameter based on the ratio of asymmetric temperature increase (, Figure 1B, where and indicates the representative temperature rise of the two coating parts.) to quantify the directional heating. Our results suggest that increasing JNP size reduces the temperature contrast. We found that the distribution of interface thermal resistance led to an asymmetric impact on the temperature contrast. Importantly, we demonstrate a significant enhancement of the temperature contrast with pulsed JNP heating compared with continuous heating. Our work advances the understanding of directional heating with JNP and brings new perspectives and potential applications to the field.

Figure 1. Schematic illustration of the modeling of JNP heating. (A) A spherical Janus nanoparticle (JNP) is heterogeneously coated, leading to nonuniform interfacial thermal resistance (ITR). The two ITRs on the JNP are , covering the north pole, and , covering the south pole. The polar angle () is defined as the critical cone angle that pinpoints the boundary between two ITRs. We impose continuous and pulsed heating on the JNP to model the steady-state and transient heating scenarios. (B) We developed an FDM numerical model and discretized the system under spherical coordinates. We defined the dimensionless parameter () to characterize the directional heating.
Method
Theoretical model
We start with establishing the theoretical model. Here we consider a plasmonic JNP with a gold core, asymmetric coating on its surface, and thus heterogeneous ITR (Figure 1A) along the interface. The JNP is submerged in an aqueous solution, and heat can transport through the interface into the water when the JNP is excited by laser radiation.35
Recently, studies reported that heat conduction under the nanoscale could deviate from Fourier’s law when the mean free path is comparable to the characteristic length.38 In this work, the temperature profile in the water domain is our primary concern. Considering that the mean free path in the water () is orders of magnitude smaller than the characteristic length (), the Fourier law should be sufficient to model the thermal transport14, 39, We applied Fourier’s law with the governing equation40:
Here, is the thermal conductivity, is the heat source, is density, and is the specific heat. We further expand the governing equation under spherical coordinates with azimuthal symmetry and simplify our model to a 2D problem (Figure 1A & Figure S1). To further simplify the model, we assume constant thermal properties. Based on our previous work, the constant property assumption introduces minimal error.14 The theoretical model is shown as follows:

Figure S1. The setup for the FDM model. We expanded the governing equation in spherical coordination and discretized the system with an orthogonal mesh. To separate the singularities in the radius direction and the polar angle direction, we adopt a 1D zone with isothermal in the polar angle direction around the original point. Here we use to denote the size of this 1D zone.
where refers to thermal diffusivity. Expanding the governing equation with spherical coordinates enables us to discretize the system with an orthogonal mesh (Figure 1B & Figure S1). However, it also has some drawbacks. As shown in Equation (2), the system will have singularities when and & and is discontinuous at the center point where the two singularities meet (, ).41 To overcome this, we assume the temperature is uniformly distributed in the direction near the center point. Thus we can further reduce the governing equation in the region near the center point to a 1D problem (Figure S2). Since the thermal diffusivity of metal is much higher than that in water, the temperature profile inside the JNP is close to isothermal, and this 1D assumption is acceptable. Consequently, the temperature governing equation is given by:

Figure S2. The mesh independence analysis for radius direction. (A) The truncation error in terms of mesh grid number in the radius direction under different biased mesh factor (). (B) Temperature contrast in terms of mesh grid number in the polar angle direction. (C) The truncation error in terms of f mesh grid number in the polar angle direction.
The boundary and initial conductions are:
refers to the radius of the 1D region (Figure S2), refers to the radius of the JNP, and refers to the radius of the boundary for the water domain. It should be noted that is the interfacial thermal resistance (ITR), and it is a function of :
where and indicate the ITR for the coating on the northern part and the ITR for the coating on the southern part, respectively, and refers to the polar angle boundary between the heterogenous coatings (Figure 1A).
Equation (3)-(5) are the mathematical description of our model, and we further developed our FDM model based on Equation (3)-(5).
Finite difference method model
Next, we developed our (Finite difference method) FDM model by discretizing Equation (3)–(5).42 Here, we adopted a biased mesh in the radius direction in the water domain to achieve higher accuracy and save computational time (Figure S1). For the steady-state problem, the left-hand side of Equation (3) equals zero, and the discretized governing equation in the water domain is as follows:
where the subscript indicates the th node in the direction, and indicates the th node in direction, indicates the biased mesh factor (). The system has a second order of accuracy, and we validated the model by conducting a mesh-independent analysis and boundary effect analysis (Figure S2 & Figure S3).

Figure S3. The boundary effect analysis of the FDM model. (A) The error of the temperature rise in JNP by comparing the result with an analytical model that has an infinite boundary size. (B) The temperature profile comparison between the analytical solution with infinite boundary size and FDM result with boundary size = 3000 nm.
For the transient problem, we discretized Equations (3)–(5) with a Crank-Nicolson scheme,43 and the discretized governing equation in the water domain is:
where superscript indicates the th node in the time direction, we further validated the accuracy and stability of the model (Figure S4), the numerical results are in consistent with analytical solutions. Equation (6) and (7) are solved with MATLAB R2020b.

Figure S4. The mesh independence for temporal direction. (A) The mesh independence analysis in the temporal direction. (B) Comparison of FDM results with ns and the analytical solution.
Results and discussion
Directional heating and temperature contrast under continuous heating (steady-state)
Several factors can affect the thermal transport and temperature profile during JNP heating, including the interfacial thermal resistance (ITR), the size of the JNP (), the polar angle of the heterogeneous coatings (), and the heating time (). Here in this section, as we focus on the directional heating under steady-state scenarios, we start with the most idealized JNP with a (Figure 1A), i.e., the JNP is heterogeneously coated equally on the two hemispheres. Nonuniform interfacial properties can stem from the heterogeneous coating, including hydrophilicity and ITR, and the contrast between ITRs can be tuned by altering the combination of coating materials or ligands.44-46 Here, we analyzed the temperature profile with different combinations of the ITRs, where and indicate the ITRs along the northern and southern hemispheres, respectively. Figure 2A shows that for a given sized JNP ( nm), the combination of and significantly affects the temperature profile. For case ① where , we have a homogeneous nanoparticle (NP) with uniform ITR; thus, the temperature is independent of the polar angle (), and a uniform temperature jump is observed across the JNP-water interface due to ITR. As we increase the contrast between ITRs, a temperature contrast in the water domain near the north pole and south pole gradually appears, and a strong positive relationship between the ITR contrast and temperature contrast is illustrated in Figure 2A, an approximately two times difference between the temperature around the north pole and the south pole is observed for case ④ (). This heterogeneous thermal transport and temperature profile are known as directional heating. Here, to quantify the temperature contrast and directional heating, we developed a dimensionless parameter which is defined as the ratio between the temperature rise in water at the north pole () and the south pole () (Figure 1B):
Figure 2. Temperature profile and temperature contrast with JANUS NP under S.S. (A) Profiles for normalized temperature rise () with Janus nanoparticle (JNP) heating. The JNP size () is 15 nm, and the cone angle for the heterogeneous coating () is . (B) 2D map of in terms of the two ITRs, , and . Dotted lines are contour lines for .
As shown in Equation (8), quantifies the temperature contrast for directional heating by characterizing the relative difference between the temperature rises. For , it indicates no temperature contrast or homogeneous heating, as shown in Figure 1A, case ①. On the contrary, when deviates from 1, it indicates considerable temperature contrast and directional heating (Figure 1A, case ④ ).
For more generalized cases with arbitrary combinations of and , we demonstrated and investigated the 2D map of in terms of and (Figure 2B), where the subscript s.s. indicating it’s under steady-state. The range for ITRs in Figure 2B (-) is consistent with ITRs reported in the literatures.14 equals to 1 along the diagonal where . On the contrary, deviates from 1 in the off-diagonal region, denoting directional heating when . It should be noted that Figure 2B is symmetry along the diagonal line due to (Figure 1A), i.e., for an idealized JNP where the two coating areas are equal, exchange the and should lead to the inverse of . On this -ITR map, we can readily read the relative temperature contrast with arbitrary combinations of and ; for instance, when and , , indicating significant directional heating, with the temperature rise near the north pole being 2.5 times higher than that near the south pole.
To further investigate how the combination of ITRs affects , we developed a circuit analogy model to analyze the JNP heating under steady-state analytically. Here we assume no heat transfer across the polar angle () of heterogeneous ITR in the water domain, and we simplified the model to a parallel circuit analogy (Figure S5A) with a set of linear equations to describe the temperature at the critical nodes (Equation (10) & (11)).

Figure S5. The parallel circuit model for the JNP heating under steady state.
Based on this parallel circuit model, can be estimated by:
Comparing results from Equation (9) with the FDM results (Figure S5B), we show that the parallel circuit model overestimates , but is more accurate with larger JNPs. This overestimation may have arisen from the assumption of no heat transfer across , and for larger JNPs, heat flux on the direction becomes less important, making it more accurate for larger JNPs. Overall, Equation (9) helps us better understand JNP heating and demonstrates the size dependence of temperature contrast with JNP heating. Based on Equation (9), for a given combination of and , increasing will yield less temperature contrast. This size dependence agrees with Kapitza number analysis,47, 48
where for larger NP, the ITR has an insignificant effect on the heat dissipation. This size dependence of is also confirmed with the FDM model, and the maps with nm and nm are shown in Fig. S6.

Figure S6.
The effect of JNP size and polar angle on the temperature contrast under S.S.
Next, we focused on the effect of polar angle () on temperature contrast under steady-state heating. In previous sections, we discussed the directional heating and temperature contrast with idealized JNPs (). In reality, can deviate from depending on the synthesis protocol (Figure S7). 28, 49 Here, we found that has a significant impact on the temperature profile as well as on . As illustrated in Figure S8, for a 30 nm JNP with , when , the JNP is homogeneously coated with ITR of , leading to (homogeneous heating). As we slightly increase , rises drastically and reaches its peak value () at . After that peak point, gradually drops as we further increase , and eventually down to 1 when , indicating homogenous heating as uniform ITR . Here we could observe an asymmetric effect of the on as the maximum value of is achieved for and . The asymmetric effect of on is also demonstrated in Figure S8.

Figure S7. Schematic illustration of the synthesize protocol for JNP.

Figure S8. The effect of the polar angle for heterogeneous coating () on the temperature profile. (A) The profile of JNP heating with different . and ,
This asymmetric effect of on can be explained by the heterogeneity of local heat flux rate () across the interface. The total heat flux () across the JNP-water interface only depends on the heating power within JNP for steady-state scenarios and can be treated as a constant. On the contrary, the local heat flux rate () across the JNP-water interface interface is heavily impacted by the heterogeneous ITR. For JNPs with a high contrast of ITRs, a major fraction of heat flux is through the interface with low ITR (Figure S9B), i.e., heat flux is regulated through a window with low ITR. As we change , that window with low resistance can be narrowed or broadened, hence changing the local thermal flux rate (Figure S8B), and a much greater local heat flux rate at the north pole () is observed for smaller whereas the local heat flux rate at the south pole () is less sensitive to . Consequently, greater temperature contrast comes with smaller as the local temperature gradient is linearly proportional to the local heat flux rate.

Figure S9. The effect of ITR contrast on the heat flux fraction through the north and southern hemisphere. (A) Schematic illustration of the heat flux through the north hemisphere () and south hemisphere (). (B) The fraction of and with different ITR contrast.
It should be noted that for different-sized JNPs and JNPs with less ITR contrasts, all the key factors, including the ITR contrast, the JNP size, and , can have a combined nonlinear effect on the temperature contrast. Here we demonstrate this combined effect by plotting the map of in terms of and with different ITR contrast under the steady state (Figure 3). Figure 3 demonstrates that the temperature contrast is more sensitive to and with high ITR contrast and vice versa. Within the range of our parameter scanning, the greatest temperature contrast () under steady-state is observed for a 3 nm JNP with and a high ITR contrast (). Our results provide estimations of the directional heating under realistic physical constraints, and we expect Figure 3 can provide guidelines for tuning the temperature contrast with JNP heating for novel applications.

Figure 3. map in terms of and with different ITR contrast under steady-state. (A) Schematic illustration of altering the and . (B-D) map in terms of and with (B) , , (C)
, , (D) , . The dotted line are contour lines for .
Directional heating during pulsed heating
In previous sections, we have discussed the directional heating and temperature contrast with JNP heating under the steady state, which is applicable for a microsecond or continuous heating. Recently, ultra-fast NP heating with femtosecond to nanosecond pulsed energy excitation has shown unique thermal responses and has played essential roles in various applications.50-52 As the characteristic thermal relaxation time () for 30 nm JNP is around 1.6 ns, JNP heating with nanosecond or shorter pulsed heating is far from steady-state. Therefore, in this section, we analyzed the evolution of temperature contrast with JNP heating during the transient process.
Here we Imposed 100 ns pulsed constant heating on a 30 nm JNP with and . Figure 4A illustrates the temperature profiles during the transient heating process.

Figure 4. The temperature evolution during the transient heating. (A) profiles during the transient heating process with JNP. nm, heating power () =35.6 W,
At ns, due to the short heating time, only a thin layer of water adjacent to the JNP-water interface is heated along the northern hemisphere, also known as thermal confinement. On the contrary, no apparent heating is observed near the southern hemisphere due to greater ITR. By comparing the local heat flux at the north pole and south pole ( and ), we can see that both the magnitude and increasing rate for are significantly higher than those for for ns, this leads to a much-enhanced relative difference between and (Figure 4B), i.e., enhanced temperature contrast. Figure 4C shows that can reach to when ns. As heating continuous, thermal energy continuously diffuses, and both and rise; However, the increasing rate for is greater than that of , ending up with a reducing as demonstrated in Figure 4C. For ns, the maximum temperature is reached as it is the end time point for the pulsed heating (Figure 4A). At this time-point, and asymptotically tend to its steady-state value (Figure 4B, ), and asymptotically falls to its steady-state level (Figure 4C, ). After the pulsed heating ( ns), the hole system cools down rapidly, and both and drop to 0 with falls to 1. To summarize, we found that is minimal for small , leading to a significant enhancement of temperature contrast, and eight times enhancement of is observed when (, nm, ), i.e., pulsed JNP heating can lead to a greater temperature contrast.
heating time () = 100 ns. , , . (B) The evolution of local heat flux rate () at the north pole and south pole during the transient heating process. (C) The evolution of and during the transient heating process. (D) The evolution of during the transient heating process, the blue dotted line indicates the corresponding .
The effect of and on temperature contrast during the transient process
In the previous section, we discussed directional heating during the transient heating process and found an enhancement of temperature contrast with puled JNP heating. This section will expand our investigation into more generalized cases and discuss the combined effects of geometric parameters ( and ) on temperature contrast during the transient heating process.
We start with the effect of the size of the JNP () on during the transient process. In our previous sections, we demonstrated a strong size dependence of for the steady-state conditions (Figure 3-D and Fig. S6). As shown in Figure 5A, we can observe a strong size dependence for throughout the transient process as well. Smaller JNPs are more sensitive to heating time and hence have a stronger enhanced temperature contrast with pulsed heating. Additionally, we analyzed the effect of in the transient process. Figure 5B illustrates the 2D map of in terms of and . For close to 0 and , JNP turns into homogeneous NP, and keeps close to 1 throughout the transient heating process. For a moderate (), we observe an enhancement of for shorter heating time. Unlike , which has a monotonic effect on throughout time, is less sensitive to at a low number () within this medium range. As heating continues, becomes more sensitive to as it tends to the steady-state scenario shown in Figure S8. Lastly, Fig. 5C demonstrates in terms of ITR contrast and heating time, and we found that for high ITR contrast (), the temperature contrast is significantly enhanced with short heating time ( when ). Whereas for low ITR contrast (), is less sensitive to heating time, and for minimal ITR contrast (), approximately keeps constant () throughout the transient process. In conclusion, we demonstrate the combined affections of the ITRs, the geometries ( and ), and the heating time on the temperature contrast. In general, smaller-sized JNP with high ITR contrast and moderate polar angle can be more sensitive to heating time and can lead to a greater temperature contrast with pulsed heating. As the first effort to shed light on the pulsed JNP heating during the transient process, we anticipate Figure 4&Figure 5 to advance our understanding of the thermal transport with JNP heating, bringing inspiration for further work and providing route maps for developing novel applications.

Figure 5. The effect of thermal resistance (), polar angle (), and size of the particle () on temperature contrast during the transient process. (A) map in terms of ITR contrast () and heating time (). Here we regulate
1 and alter (B) map in terms of and . (C) map in terms of and . The dotted lines are contour lines for .
Conclusion
In this work, we focused on thermal transport and directional heating with Janus nanoparticle (JNP) heating. We developed an FDM numerical framework and defined a dimensionless parameter () to characterize the temperature contrast. Based on this, we analyzed the effect of ITR contrast, , and on temperature contrast under steady-state and transient heating. First, we found a significant size dependence of temperature contrast, where a smaller JNP can lead to greater temperature contrast. Additionally, we reveal the role of and demonstrate its asymmetric effect on temperature contrast, finding that the maximum is observed at . Importantly, we shed light on the temperature evolution near a JNP during a transient heating process and found a significant enhancement of the temperature contrast with pulsed JNP heating. We expect our work can help us better understand thermal transport with JNP heating and advance the field with new inspirations.
Acknowledgment
I am grateful for the useful suggestions from Dr. Yaning Liu and Dr. Hui Ouyang.
Research reported in this publication was supported by National Institute of General Medical Sciences and National Institute of Allergy and Infectious Diseases of the National Institutes of Health under award numbers R35GM133653 and R01AI151374, the National Science Foundation under award number 2123971, and the American Heart Association under award number 19CSLOI34770004. The content is solely the responsibility of the authors and does not necessarily represent the official views of funding agencies.
Associated Content
Supporting information (Docx)
Author Information
Corresponding Author: Zhenpeng Qin*
Department of Mechanical Engineering, University of Texas at Dallas, 800 West Campbell Road EW31, Richardson, Texas 75080, United States.
E-mail: [email protected]
ORICD: 0000-0003-3406-3045
Author Contributions
C.X. developed the numerical model and did the computational work and analysis. B.W. and Z.Q. participated in conceptualization and analysis. All authors contributed to the writing of the manuscript. Z.Q. directed the research.
Funding
The research reported in this work was partially supported by the National Institute of General Medical Sciences (NIGMS) of the National Institutes of Health (award number R35GM133653), the Collaborative Sciences Award from the American Heart Association (award number 19CSLOI34770004), and the High-Impact/High-Risk Research Award from the Cancer Prevention and Research Institute of Texas (award number RP180846). The content is the sole responsibility of the authors and does not necessarily represent the official views of the funding agencies.
Nomenclature
Roman letters
Interfacial thermal resistance along the north hemisphere of Janus nanoparticle,
Interfacial thermal resistance along the south hemisphere of Janus nanoparticle,
Thermal conductivity,
Thermal conductivity in Janus nanoparticle,
Thermal conductivity in water,
Temperature, K
Temperature in the Janus nanoparticle, K
| Symbol | Definition |
| Temperature in water, K | |
| Heating power, W m | |
| Specific heat, J kg | |
| Time, s | |
| Radius, m | |
| Radius of the 1D zone, m | |
| Radius of the Janus nanoparticle, m | |
| Radius of the water domain, m | |
| Thermal diffusivity, m s | |
| Thermal diffusivity in Janus nanoparticle, m s | |
| Thermal diffusivity in water, m s | |
| Interfacial thermal resistance, m K W | |
| Interfacial thermal resistance on the north hemisphere, m K W | |
| Interfacial thermal resistance on the southern hemisphere, m K W | |
| Kaptiza number, | |
| Kaptiza number on the north hemisphere, | |
| Kaptiza number on the southern hemisphere, | |
| Heat flux, W |
Table 1.
Heat flux through the north hemisphere, W
Heat flux through the southern hemisphere, W
Heat flux rate, Wm
Heat flux rate at the north pole, Wm
Heat flux rate at the south pole, Wm
Fourier number,
Greek symbols
Polar angle
The critical polar angle that pinpoints the boundary between the heterogeneous interfacial thermal resistances.
Dimensionless parameter to characterize the temperature contrast,
Dimensionless parameter to characterize the temperature contrast for steady-state.
Density, kg m
Characteristic thermal relaxation time, , s
Abbreviations
JNP Janus nanoparticle
ITR Interfacial thermal resistance
MD Molecular dynamic
FDM Finite difference method
S.S. Steady-state
REGULATING NANOSCALE HEAT TRNSFER WITH JANUS NANOPARTICLES
Supporting information for
This PDF file includes:
Equations S1 to S3
Figures S1 to S9
We validated our model by doing a comprehensive mesh dependency analysis. Here, we start with the mesh in the radius and the polar direction for the steady-state model. We assume uniform interfacial thermal resistance (ITR) along the JNP-water interface, thus making a homogenous NP heating where the analytical solution is available. As we have a linear biased mesh grid in the radius direction, we analyzed the truncation error by comparing the FDM results with the analytical solution with different biased mesh factor () and mesh density. The error is calculated by the following equation:
As shown in Figure S2A, when , we have a uniform mesh, and the truncation error drops as we increase the mesh density; when the mesh grid number is 140, the error is around 1%. When , we have a biased mesh, and the error drops much faster as the mesh density increases; when the mesh grid number is 50, the error is around 0.1%. This is because the biased mesh gives a higher mesh density near the JNP where the greatest temperature gradient is observed (Figure S1), and thus greatly reduces the error and makes the mesh more efficient. As we continuously increase (), we found that the FDM results become less stable as we increase the mesh density. This might be because the over-biased mesh has coarse mesh grids near the boundary, which can bring extra error. In summary, we validate our model in the radius direction; we found a properly biased mesh factor () and a mesh density (50, minimum nm); based on this setup, the truncation error is at the order of 0.1%.
Next, we did the mesh independence analysis in the polar angle () direction. Here we introduced a heterogeneous ITR and investigated the temperature contrast () with different mesh densities. Figure S2B demonstrates that the value of converges as the mesh density increases. Here we assume the results at mesh grid = 275 is the accurate solution, and we calculate the error by comparing the results with this accurate solution (Figure S2C); we could see the error is at the magnitude of 0.1% for the mesh grid = 100 ().
We chose a truncation error of 0.1% that indicates sufficient accuracy for our mesh set-up; thus, we will keep the set-up (, minimum nm, ) for the steady-state modeling throughout our paper.
Next, we analyzed the boundary effect. In reality, a free JNP can be treated as a single JNP surrounded by infinite water. In our model, we cannot have an infinite water domain, and the size of the boundary of the water domain can bring error, i.e., boundary effect. Here we calculated the error of boundary effect by comparing the FDM result with a finite boundary radius and the analytical solution with an infinite boundary size. As shown in Figure S3A, for boundary radius = 3000 nm (200 × ) the error of boundary effect drops to 1%, and we believe this is accurate for our analysis (Figure S3B). We will keep this set-up throughout our paper.
Finally, we analyzed mesh independence and validated the model in the temporal direction. The spatial mesh set-ups are identical to the steady-state model. Here we plot the FDM results in terms of temporal mesh density (Figure S4A), we found that the FDM results converge as mesh density increases, and we believe a temporal mesh interval of 0.1 ns can bring sufficiently accurate results. Here we further compared the FDM result with the analytical solution (Figure S4B),1 and demonstrated that the FDM results are consistent with the analytical solutions.
For the parallel circuit model, the thermal transport with JNP can be described with a set of linear equations:
By solving Equation (11), we have the temperature rise at the north pole and south pole:

Figure S6 (PDF p. 37). map in terms of and with different and .
nm. (B) The local heat flux rate across the interface at northern pole () and southern pole () in terms of . (C) and in terms of . (D) in terms of .
Reference:
References
- [1]Goldenberg, H.; Tranter, C., Heat flow in an infinite medium heated by a sphere. British Journal of Applied Physics 1952, 3 (9), 296.