WorksPhysics and Astronomy
Crystal structure, magnetic properties and magnetocaloric performance of RERhIn (RE = Gd-Tm) compounds
Abstract
Polycrystalline samples of the RERhIn (RE = Gd–Tm) intermetallics have been investigated by means of X-ray diffraction (XRD) as well as by DC and AC magnetometric measurements. The XRD data confirm that the compounds crystallize with the orthorhombic LuNiIn-type structure (space group Pbam, No. 55). With decreasing temperature, RERhIn spontaneously order magnetically with the critical temperatures of magnetic order equal to 10.6, 14.2, 15.4, 7.2, 5.9 and 4.9 K for RE = Gd, Tb, Dy, Ho, Er and Tm, respectively. The compounds have complex magnetic properties, showing features characteristic of both ferro- and antiferromagnetic orderings. Moreover, the magnetic properties change with increasing number of the 4f electrons from predominantly ferromagnetic in GdRhIn to predominantly antiferromagnetic in TmRhIn. The magnetic data indicate that only the rare earth atoms carry magnetic moments. The maximum magnetic entropy change () at the 0-9 T magnetic flux density change () equals 12.4 JkgK at 17 K for GdRhIn, 11.3 JkgK at 28 K for TbRhIn, 13.1 JkgK at 19 K for DyRhIn, 16.4 JkgK at 12 K for HoRhIn, 15.3 JkgK at 8 K for ErRhIn and 12.6 JkgK at 6.5 K for TmRhIn. For a selected rare earth element (RE), the member of the RERhIn family of compounds reaches the highest value, when compared with its RETIn (T = Ni, Pd, Pt) isostructural analogues, making the RERhIn intermetallics a good choice for application in low-temperature magnetic refrigeration.
Introduction
Rare earth intermetallics have attracted researchers’ interest for many decades because of their intriguing physical properties, such as complex/ frustrated magnetic structures, metamagnetism, large magnetocaloric effect (MCE), valence fluctuation, heavy fermion behavior, and Kondo effect. Among these compounds, the ones with multiple magnetic sublattices are of special interest as individual magnetic sublattices may be characterized by individual propagation vectors, individual directions of magnetic moments and individual critical temperatures of magnetic ordering. Often additional temperature-induced order–order magnetic transitions appear in this class of materials.
The magnetocaloric performance phenomenon, in which certain materials experience temperature changes in response to an externally applied magnetic field, has attracted wide interest because of the potential in magnetic refrigerant applications. Recent investigations on the magnetic properties and magnetocaloric effects of certain rare-earth intermetallics can be found in both review articles and publications focusing on individual compounds [1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45].
Among ternary intermetallics, the RE₅T₂In₄ family of compounds, where RE – rare earth element, T – transition metal element (T = Ni [46], Rh [47], Pd [48], Pt [49]) are of special interest due to their intriguing magnetic properties. These compounds crystallize in the orthorhombic structure of the Lu₅Ni₂In₄-type (Pbam space group, No. 55), where rare earth atoms occupy three distinct Wyckoff sites: the 2a site and two 4g sites with unique atomic positional parameters [46]. It is worth noting that the Lu₅Ni₂In₄ crystal structure is characteristic of compounds with general composition of REm+nT₂nXₘ, where RE – rare earth element, T – transition metal element and X – p-electron element, while m and n value represent the numbers of the REIn (CsCl-type) and RET₂ (AlB₂-type) slabs forming the structure.
In the RE₅Ni₂In₄ system, Tb₅Ni₂In₄ exhibits ferromagnetic/ferrimagnetic behavior below K with an additional antiferromagnetic component appearing below 20 K [50], while Dy₅Ni₂In₄ has ferromagnetic-like ordering below 105 K, followed by multiple magnetic phase transitions at lower temperatures [51]. Ho₅Ni₂In₄ orders antiferromagnetically below the Néel temperature of K and transforms to ferromagnetic/ferrimagnetic structure at K [50], though another study reports K [52]. A different paper reports ferromagnetic ordering in HoNiIn below K [53]. ErNiIn shows ferromagnetic ordering below 21 K [52]. Neutron diffraction data reveal a complex magnetic structure in ErNiIn, containing both ferromagnetic and antiferromagnetic components. The critical temperature of magnetic ordering is found to be 18.5 K and it is followed by several additional magnetic transitions occurring at lower temperatures [54]. TmNiIn shows complex antiferromagnet character with a Néel temperature of 4.2 K [55] or 4.1 K [56].
In the REPdIn system, a ferromagnetic ordering is established in TbPdIn and DyPdIn below the Curie temperatures of 97 K and 88 K, respectively. As the temperature decreases, TbPdIn turns into an antiferromagnet, while DyPdIn becomes a ferrimagnet. For HoPdIn, a complex antiferromagnet emerges below its Néel temperature of 28.5 K, comprising two distinct antiferromagnetic components, one of which transitions into a ferrimagnetic state at lower temperatures. A canted antiferromagnetic structure is found in ErPdIn below K, with additional ferromagnetic component developing at lower temperatures. TmPdIn shows antiferromagnetic behavior below K with two different antiferromagnetic components. Analysis of the neutron diffraction data for REPdIn (RE = Gd–Er) indicates that the rare-earth moments at the 2a and 4g2 sites order at higher temperatures than those at the 4g1 site [57].
In the REPtIn system, DC and AC magnetic data reveal a transition from paramagnetic state to a ferromagnetic or ferrimagnetic one for RE = Gd–Er. The Curie temperatures equal 76, 108, 23.5 and 12.6 K for RE = Gd, Tb, Ho and Er, respectively. With decreasing temperature, additional anomalies in the magnetic susceptibility are observed for RE = Gd, Ho and Er. TmPtIn is found to be antiferromagnetic below K [58]. The neutron diffraction data for RE = Tb–Er reveal complex magnetic structures having both ferro-and antiferrromagnetic temperature-dependent components. As a result, the magnetic structures show a number of temperature-induced transformations for RE = Tb–Er. In contrary, a non-collinear antiferromagnetic structure with no extra magnetic transitions is detected in TmPtIn [59].
Up to now, the magnetocaloric properties of RETIn (RE = rare earth element, T = transition metal element) have been reported for selected compounds only, namely for RENiIn (RE = Dy, Ho, Er) [52], REPdIn (RE = Tb–Tm) [60] and REPtIn (RE = Gd–Tm) [58].
Until now, there is only one paper on the physical properties of RERhIn (RE = rare earth element) limited to basic crystallographic data solely. It motivated us to undertake the current study, in which we report detailed crystallographic characterization and magnetic properties (including magnetocaloric effect) of the RERhIn (RE = Gd–Tm) intermetallics with multiple magnetic sublattices. The experimental results reported in this work are compared with those reported previously for the isostructural compounds, including RENiIn [46, 50, 51, 52, 53, 54, 55, 56], REPdIn [48, 57, 60] and REPtIn [49, 58, 59].
Materials and methods
High-purity elements with at least 99.9 wt % of RE = Gd-Tm, as well as Rh and In have been selected as raw materials for arc-melting in a titanium-gettered argon atmosphere with the RE:Rh:In atomic ratio of 5:2:4. The obtained ingots have been remelted for a few times in order to ensure their homogeneity.
The phase composition of the samples has been identified by the X-ray powder diffraction at the room temperature using PANalytical X’Pert PRO diffractometer (Cu K-radiation, Bragg-Brentano geometry, angle interval of – , continuous scan mode, step size in , 300 s/step). The FullProf program has been used for Rietveld analysis of the collected X-ray diffraction data set [61, 62].
For the magnetometric measurements, the powder samples have been encapsulated in plastic containers and glued with low-temperature varnish in order to prevent random grain rotation during measurement.
The DC magnetic susceptibility has been measured with the Vibrating Sample Magnetometer (VSM) option of Physical Properties Measurement System (PPMS) by Quantum Design, equipped with a superconducting magnet running up to 9 T (90 kOe). The data have been collected while heating over the 1.85 - 390 K temperature interval, in presence of the magnetic field of 1 kOe. Zero Field Cooling (ZFC) regime has been applied to the first measurement, while the Field Cooling (FC) one to the second run. Next, the sample has been heated above its critical temperature of magnetic ordering, then demagnetized by the oscillating magnetic field, and after that cooled down to 1.9 K. At the latter temperature an isothermal magnetization curve has been collected starting from zero field up to the maximum available field of ±90 kOe. In order to study MCE, a number of magnetization vs. temperature curves have been measured under fixed magnetic field ranging from 10 kOe (1 T) up to 90 kOe (9 T) with a step of 10 kOe. Before each measurement, the sample has been demagnetized by the oscillating magnetic field at temperature above respective critical temperature of magnetic ordering, and cooled down to 2 K subsequently. Then the desired value of magnetic field has been set. The data have been collected from 2 K up to temperature well above the transition to the paramagnetic state. The procedure has been repeated several times until reaching the maximum value of magnetic field.
The AC magnetic susceptibility has been measured with the AC Measurement System (ACMS) option of PPMS. The data have been collected from 1.9 K up to temperature above the respective critical temperature of magnetic ordering in the presence of oscillating magnetic field with amplitude Oe and direct magnetic field of kOe. Based on these data, the real () and imaginary () parts of AC magnetic susceptibility have been determined for the frequencies of 500, 1000 and 2500 Hz.
Crystal structure
Figure 1 shows the result of Rietveld refinement of X-ray powder diffraction patterns of RERhIn (RE = Gd-Tm). The samples are found to contain at least 97 wt % of the main RERhIn phase with minor amounts of RERh or elemental In for selected samples. The exact samples’ compositions can be found in Table I.

Figure 1. X-ray diffraction patterns at room temperature of RERhIn: (a) RE = Gd, (b) RE = Tb, (c) RE = Dy, (d) RE = Ho, (e) RE = Er, and (f) RE = Tm. The black solid circles show the experimental data, while the red lines show the Rietveld refinement results. The first row of vertical bars denotes Bragg reflection positions related to the main RERhIn phase, while the second one refers to RERh (c) and elemental In (a, b, c, f). The blue line at the bottom shows the difference between the experimental data and the refinement results.
| RE | Gd | Tb | Dy | Ho | Er | Tm |
| [Å] | 18.1754(36) | 18.1150(26) | 18.0596(23) | 18.0205(17) | 17.9783(17) | 17.9462(14) |
| [Å] | 8.0062(16) | 7.9707(12) | 7.9529(10) | 7.9422(7) | 7.9265(7) | 7.8994(6) |
| [Å] | 3.6627(9) | 3.6329(7) | 3.6078(6) | 3.5848(4) | 3.5649(5) | 3.5450(4) |
| [Å] | 532.98(20) | 524.56(14) | 518.17(12) | 513.06(9) | 508.02(9) | 502.56(8) |
| RE1 at | 0 | 0 | 0 | 0 | 0 | 0 |
| RE2 at | 0.2216(6) | 0.2186(5) | 0.2205(4) | 0.2198(4) | 0.2205(3) | |
| 0.2483(16) | 0.2422(14) | 0.2449(11) | 0.2464(11) | 0.2469(9) | ||
| RE3 at | 0.4165(6) | 0.4153(2) | 0.4154(4) | 0.4140(4) | 0.4130(3) | |
| 0.1217(13) | 0.1190(10) | 0.1206(9) | 0.1220(10) | 0.1205(7) | ||
| Rh at | 0.3010(9) | 0.3011(8) | 0.3040(7) | 0.3037(5) | 0.3032(6) | |
| 0.0148(22) | 0.0237(17) | 0.0272(13) | 0.0258(16) | 0.0275(13) | ||
| In1 at | 0.5703(7) | 0.5693(6) | 0.5680(5) | 0.5682(6) | 0.5668(4) | |
| 0.2063(14) | 0.2087(12) | 0.2076(9) | 0.2087(10) | 0.2057(8) | ||
| In2 at | 0.8491(7) | 0.8493(6) | 0.8494(5) | 0.8491(5) | 0.8492(4) | |
| 0.0717(16) | 0.0710(13) | 0.0700(10) | 0.0684(12) | 0.0723(10) | ||
| [%] | 1.99 | 2.14 | 1.71 | 2.53 | 2.89 | 2.47 |
| [%] | 7.43 | 6.23 | 6.69 | 4.34 | 6.42 | 4.29 |
| [%] | 9.49 | 8.33 | 7.69 | 5.37 | 8.11 | 5.33 |
| 5.13 | 5.43 | 2.28 | 8.29 | 8.78 | 6.91 | |
| Sample composition | ||||||
| RERhIn [wt %] | 97.1(4) | 98.3(3) | 97.5(6) | 100 | 100 | 99.3(2) |
| RERh [wt %] | 0.4(5) | |||||
| In [wt %] | 2.9(4) | 1.7(3) | 2.1(3) | 0.7(2) |
Table I. Crystallographic data obtained from Rietveld refinement of the X-ray powder diffraction patterns at room temperature of RERhIn (RE = Gd-Tm) with LuNiIn-type structure, space group , No. 55, where the RE atoms in crystal unit cell occupy three nonequivalent positions. The following factors , , , and are reported. If present, the impurity phases are listed at the bottom of the table.
RERhIn (RE = Gd-Tm) crystallize in the orthorhombic LuNiIn-type of crystal structure (space group , No. 55), which has been reported for the first time by Zaremba et al. [46]. The structure consists of the (001) planes () containing rare earth atoms distributed among three non-equivalent Wyckoff sites, namely, the 2a site (0,0,0) and two 4g sites () with individual and atomic positional parameters. The rare earth planes are separated by the planes consisting of two remaining elements (). The transition metal occupies one 4h site (), while the In atoms occupy two other 4h sites with individual and atomic positional parameters. A projection of the crystal structure onto ab-plane, together with RE-RE interatomic distances, is presented in Figure 2.

Figure 2. The crystal unit cell of TmRhIn projected onto the ab-plane. A network formed by the rare earth atoms and RE-RE interatomic distances are indicated.
The values of lattice parameters, unit cell volumes and atomic positional parameters, as derived from Rietveld refinement of the patterns shown in Figure 1, are listed in Table I. They agree well with the ones reported previously [47].
Results and Discussion
Basic magnetic properties
Figure 3 presents temperature dependences of reciprocal magnetic susceptibilities collected at kOe for RERhIn (RE = Gd-Tm). Theory predicts that a material which contains solid magnetic moments and shows spontaneous magnetic ordering at low temperatures should follow the Curie-Weiss law (which is an extension of the Curie’s law with Weiss’s molecular field [63, 64]) at its paramagnetic temperature region, i.e. above the critical temperature of magnetic ordering. The Curie-Weiss law is given by the following equation:

Figure 3. DC reciprocal magnetic susceptibility with the fitted line representing the Curie-Weiss law (prime graph), the low-temperature ZFC and FC behavior measured at 1 kOe (upper insets), and the isothermal magnetization vs. external magnetic field loops at 1.9 K (lower insets) for : (a) , (b) , (c) (d) , (e) , and (f) . The transition temperatures listed in Table II are indicated with arrows in the upper insets.
where is the Curie constant and is a parameter called Curie-Weiss temperature or paramagnetic Curie temperature. The fitted Curie-Weiss formula at high temperature range for RERhIn (RE = Gd-Tm) is represented by solid lines in Figure 3. Based on the slopes and intercepts of the fitted lines, the effective magnetic moments () and paramagnetic Curie temperatures () have been determined. Their values are listed in Table II. It is worth noting that the effective magnetic moments for RERhIn (RE = Gd-Tm) are close to the corresponding theoretical values predicted for the RE ions, indicating that the magnetism in the investigated compounds is solely or predominantly related to the magnetic moments of the rare earth ions. The upper insets in Figure 3 show ZFC and FC temperature dependence of DC magnetic susceptibility collected at 1 kOe, while the lower insets present isothermal magnetization loops taken at 1.9 K. The magnetic moments at K and kOe reach 88 % of its theoretical RE ion value for RE = Gd and not more than 66 % of corresponding free ion values for the remaining RE = Tb-Tm (see Table II). Such a huge reduction of magnetic moment in the ordered state is usually attributed to the interaction with the crystalline electric field (CEF). However, one should also take into account that the lack of saturation at K and kOe also contributes to the reduction of the experimental values.
| RE | [K] | [K] | [K] | [K] | [] | [] | [kOe] | [kOe] | ||||||||
| Exp. | Theor. | Exp. | Theor. | |||||||||||||
| Gd | +17.9 | 8.37 | 7.94 | 6.15 | 7.00 | 0.40 | 0.17 | |||||||||
| Tb | +6.9 | 10.02 | 9.72 | 5.08 | 9.00 | 28 | 0.76 | |||||||||
| Dy | -4.5 | 10.77 | 10.65 | 6.03 | 10.00 | 9.3, 24 | 0.72 | |||||||||
| Ho | +1.4 | 10.36 | 10.61 | 6.54 | 10.00 | 10 | 0.14 | |||||||||
| Er | +1.9 | 9.54 | 9.59 | 5.55 | 9.00 | 7.7, 12 | 0.22 | |||||||||
| Tm | +0.2 | 7.57 | 7.57 | 3.71 | 7.00 | 9.3 |
Table II. Parameters characterizing magnetic order as derived from DC and AC magnetometric measurements: (Curie temperature), (Néel temperature), (temperatures of additional anomalies), (paramagnetic Curie temperature), (effective magnetic moment), (magnetic moment in the ordered state), (the critical field of metamagnetic transition) and (the coercivity field) for RERhIn (RE = Gd-Tm). The index indicates a transition temperature corresponding to a maximum in the curve, the index the one corresponding to an inflection point, while the index the one corresponding to a kink. The transition temperatures derived from the AC magnetometric measurements are based on the data at 1 kHz. The values of , and have been determined from the data collected at 1.9 K in magnetic fields up to 90 kOe.
Figure 4 reveals the temperature behavior of the real and imaginary parts of the AC magnetic susceptibility collected in presence of kOe in order to make the results consistent with those in Figure 3.
Figure 4. The real () and imaginary () parts of AC magnetic susceptibility taken at frequencies of 500 Hz, 1000 Hz and 2500 Hz for RERhIn: (a) RE = Gd, (b) RE = Tb, (c) RE = Dy, (d) RE = Ho, (e) RE = Er, and (f) RE = Tm, respectively. The transition temperatures indicated with arrows are listed in Table II.
The magnetic transition temperatures together with critical fields related to metamagnetic transitions and coercivity fields are listed in Table II. As the RERhIn (RE = Gd-Tm) compounds show complex magnetic behavior, indicating the presence of both ferro- and antiferromagnetic components of low-temperature magnetic structures, their basic magnetic properties are analyzed individually in the following subsections.
GdRhIn
With decreasing temperature, the DC magnetic susceptibility of GdRhIn has a slight maximum at about 11 K followed by a plateau (see the upper inset in Figure 3a). Usually, a maximum is characteristic of antiferromagnetic order. However, there is a lot of evidence for the existence of the ferromagnetic component of the magnetic structure too, namely, divergence of the ZFC and FC susceptibility curves below 11 K, positive value of the paramagnetic Curie temperature of +17.9 K, shape of the isothermal magnetization loop collected at 1.9 K, which is typical of a soft ferromagnetic material with coercivity field of 0.17 kOe at 1.9 K (see the lower inset in Figure 3a) as well as distinct maximum in the imaginary component of the AC magnetic susceptibility () (see Figure 4a). A weak antiferromagnetic component of the magnetic structure is confirmed by metamagnetic transition occurring at the small critical field of 0.50 kOe as derived from the primary isothermal magnetization curve taken at 1.9 K. Summarizing, the results of magnetic measurements state that the low-temperature magnetic structure in GdRhIn consists of both ferro- and antiferromagnetic components with predominant ferromagnetic character.
Tb5Rh2In4
DC magnetic susceptibility of TbRhIn is typical of a ferromagnet with inflection point at about 14 K, indicating the Curie temperature and divergence of the ZFC and FC susceptibility curves below . Predominant ferromagnetic character of the magnetic order is also confirmed by a positive value of the paramagnetic Curie temperature of +6.9 K, coercivity field of 0.76 kOe at 1.9 K as well as distinct maximum in visible near . An antiferromagnetic component of the magnetic structure is also present as the primary isothermal magnetization curve (taken at 1.9 K) reveals a metamagnetic transition
at the critical field of 28 kOe. The shape of the isothermal magnetization loop at 1.9 K confirms coexistence of ferro- and antiferromagnetic contributions to the magnetic order, as the magnetic field hysteresis at 1.9 K is relatively small below the critical field of metamagnetic transition () while it increases rapidly for the magnetic fields exceeding , where the antiferromagnetic component of the magnetic structure is suppressed by application of high magnetic field (see the lower inset in Figure 3b).
Dy5Rh2In4
With decreasing temperature, the DC magnetic susceptibility of DyRhIn shows two transitions: a small kink at of about 15 K, followed by another magnetic transition manifesting itself by maximum at of about 10 K. Although a divergence of the ZFC and FC susceptibility curves, revealing a ferromagnetic contribution to the magnetic order, is visible below , there is only a very small anomaly in at indicating rather antiferromagnetic character of magnetic order between and . The ferromagnetic component of the magnetic structure is enhanced at , where reaches its local maximum. The isothermal magnetization curve collected at 1.9 K shows features characteristic of both ferro- and antiferromagnetic ordering, namely, visible hysteresis with a coercivity field of 0.72 kOe (ferromagnetic character), while the primary magnetization curve reveals two subsequent metamagnetic transitions with critical fields equal to 9.3 and 24 kOe, respectively (antiferromagnetic character). The predominant nature of the magnetic interactions is antiferromagnetic, as the paramagnetic Curie temperature is negative ( K).
Ho5Rh2In4
DC magnetic susceptibility of HoRhIn has a maximum typical of para- to antiferromagnetic transition at about 7 K. The predominant antiferromagnetic character of magnetic order is confirmed by the shape of the isothermal magnetization loop taken at 1.9 K with a distinct metamagnetic transition at kOe. A small ferromagnetic component of the magnetic structure is also present, as the coercivity field of 0.14 kOe is observed at 1.9 K, a divergence of the ZFC and FC DC magnetic susceptibility curves is visible below the critical temperature of the magnetic ordering, as well as there is a tiny anomaly in at . The paramagnetic Curie temperature is found to be +1.4 K. It is positive, but close to zero, indicating no clear dominance of either ferro- or antiferromagnetic interactions.
Er5Rh2In4
With decreasing temperature, the DC magnetic susceptibility of ErRhIn shows a maximum at K, characteristic of para- to antiferromagnetic transition, followed by a rapid decrease at K. The isothermal magnetization loop at 1.9 K is typical of an antiferromagnet with two distinct metamagnetic transitions at 7.7 and 12 kOe. Presence of small ferromagnetic contribution to the magnetic structure is confirmed by the existence of coercivity field equal to 0.22 kOe at 1.9 K, divergence of the ZFC and FC DC magnetic susceptibility curves below as well as tiny anomalies in present at both and . However, it should be emphasized that these anomalies reach very low values when compared with the values of at the respective temperatures. The paramagnetic Curie temperature of +1.9 K is positive, but too small to favor in a clear way predominant character of the magnetic order.
Tm5Rh2In4
DC magnetic susceptibility of TmRhIn has a maximum typical of para- to antiferromagnetic transition at about 5 K. The predominant antiferromagnetic nature of the magnetic order is confirmed by the shape of the isothermal magnetization loop at 1.9 K, characterized by a metamagnetic transition at 9.3 kOe and lack of detectable coercivity field, as well as lack of visible divergence of the ZFC and FC DC magnetic susceptibility curves below the critical temperature of the magnetic ordering. Nevertheless, a very small ferromagnetic compo-
nent of the magnetic structure may be present, as there is a tiny anomaly in . However, it is more than two orders of magnitude smaller than the corresponding anomaly in .
Discussion on the basic magnetic properties
As shown above, the RERhIn (RE = Gd-Tm) intermetallics have complex magnetic properties characterized by the presence of both ferro- and antiferromagnetic components of their low-temperature magnetic structures. Therefore, the resultant magnetic structures arise from competition between magnetic interactions of different character. Such a result is closely related to the complex crystal structure, where the rare earth atoms occupy three non-equivalent Wyckoff sites and each site has its own arrangement of the neighbouring ions.
According to the crystallographical data reported in [47], the rare earth interatomic distances in RERhIn (RE = Gd-Tm) exceed 3.35 Å (see the RE-RE interatomic distances indicated in Figure 2, as well as the values of the lattice parameters listed in Table I. Therefore, they are high enough to exclude any direct exchange interactions between the subshells of the RE ions, which carry magnetic moments in the investigated compounds. In such a case, the indirect exchange interactions of the Ruderman-Kittel-Kasuya-Yosida (RKKY)-type are expected in this family of compounds. One of the predictions of the RKKY theory is the so-called de Gennes scaling, which assumes direct proportionality between the critical temperature of magnetic ordering and the de Gennes factor defined as , where is a Landé factor, while is a total angular momentum of the RE rare earth ion [65].
Figure 5 presents the critical temperatures of magnetic ordering for RE₅T₂In₄ (T = Ni, Pd, Pt, Rh) plotted against the de Gennes factor. The dotted lines show theoretical de Gennes behavior calculated for RE₅Pt₂In₄ and RE₅Rh₂In₄, where the critical temperatures of magnetic ordering for the Gd-based compounds are available and taken as a reference. This is because, according to the Hund’s rules, the Gd ions do not interact with CEF. Distinct deviations from proportionality, visible for all families of compounds, can be attributed to the influence of crystalline electric field (CEF) [66]. Such a result is in agreement with values of the magnetic moments of RE₅Rh₂In₄ (RE = Gd-Tm) in the magnetically ordered state (at K and kOe) as listed in Table II. The magnetic moment of Gd₅Rh₂In₄ reaches 88 % of the theoretical Gd ion value while the moments of the remaining compounds with RE = Tb-Tm are significantly reduced and do not exceed 66 % of corresponding free ion values. Reduction of the magnetic moments for RE = Tb-Tm is another evidence for interactions of the rare earth ions with CEF and emphasizes influence of this type of interactions on the resultant magnetic structures. For a selected rare earth element among Gd, Tb, Dy, Ho and Er, the critical temperature of the Rh-based RE₅T₂In₄ compound is significantly lower than the temperatures of the Ni-, Pd- and Pt-based isostructural intermetallics (see Figure 5). As differences in the lattice parameters for a fixed RE element are less than 1 % they can not explain such a large difference in the magnetic ordering temperatures. However, one should take into account that Rh has one d-electron less in its unfilled d-subshell than Ni, Pd and Pt. Therefore, differences in the magnetic ordering temperatures are rather related to the electronic structures of the compounds under investigation. Unfortunately, there are no reports about electronic structure of the Rh-based RE₅T₂In₄ compounds, while there is one study reporting the electronic structures of the isostructural Sc₅T₂In₄ (T = Ni, Pd and Pt) [67]. The latter compounds have similar electronic structures. This result coincides with similar magnetic ordering temperatures observed in RE₅T₂In₄ (RE = Tb-Tm; T = Ni, Pd, Pt) for a fixed RE element – see the data in Figure 5. Investigation of the correlation between magnetic ordering temperature and electronic structure is possible in case of the Gd₃T compounds, which crystallize in the orthorhombic crystal structure of the Fe₃C-type, where Gd occupies two non-equivalent Wyckoff sites (4c and 8d) [68]. Gd₃T are found to order magnetically below 112 and 325 K for T = Rh and Pd, respectively [69]. The valence band in Gd₃Rh is formed by the hybridized Gd 5d and Rh 4d states (the latter ones located 2.1 eV below the Fermi level) [70], while the valence band in Gd₃Pd origins mainly from the Gd 5d states as the Pd 4d states have binding energy of 3.63 eV [71]. Hybridization of the Gd 5d and Rh 4d states leads to partial depopulation of the Gd 5d states at the Fermi level. Taking into account electronic structures in Gd₃Rh and Gd₃Pd, a much stronger depopulation effect is expected for Gd₃Rh than for Gd₃Pd. As the RKKY theory of exchange interactions predicts that the critical temperature of magnetic ordering is proportional to the density of states (DOS) at the Fermi level [65], the Rh-based rare earth intermetallics are expected to have lower magnetic ordering temperatures than the isostructural Pd-based ones. Difference in location of the transition metal 4d states is also observed in the HoTX (T = transition metal; X = p-electron element) intermetallics that crystallize in the orthorhombic crystal structure of the TiNiSi-type. The UPS and XPS spectra reveal binding energy of the Rh 4d states equal to 3.0 eV in HoRhSi and to 2.4 eV in HoRhGe, while the Pd 4d band in HoPdSn is 4.2 eV below the Fermi level [72].
Figure 5. Critical temperatures of magnetic ordering () vs. de Gennes factor for RE₅T₂In₄ (RE = rare earth element, T = Ni [50, 51, 53, 54, 56], Pd [57], Pt [58], and Rh (this work)). Gd-based compounds are taken as a reference.
Magnetocaloric effect
Magnetic entropy change and temperature averaged magnetic entropy change (TEC)
Figure 6 shows temperature dependences of magnetization taken at selected magnetic fields. Based on these data, magnetic entropy change can be derived by using the Maxwell relation as follows:
Figure 6. ZFC magnetization vs. temperature curves in magnetic flux densities between 1 T and 9 T for : (a) RE = Gd, (b) RE = Tb, (c) RE = Dy, (d) RE = Ho (e) RE = Er, and (f) RE = Tm.
where represents the difference between the final and initial magnetic flux densities, while is the derivative of magnetization over temperature at a fixed magnetic flux density [73].
Usually, the initial magnetic flux density is fixed to zero. This convention is also used in the current study.
Figure 7 presents the calculated temperature dependencies of magnetic entropy change for (RE = Gd-Tm) as derived from the data shown in Figure 6 using Eq. (2). The magnetic entropy change reaches its maximum value in the vicinity of the respective temperature of transition from para- to magnetically ordered state. Maximum magnetic entropy change equals 12.4, 11.3, 13.1, 16.4, 15.3, and 12.6 under magnetic flux density change of 0–9 T for RE = Gd, Tb, Dy, Ho, Er, and Tm, respectively. The temperatures at which the maximum value of is found together with magnetic entropy changes, under selected values of magnetic flux density change, are listed in Table III. The same table also contains the values reported for other selected rare-earth-based compounds. It is worth noting that magnetic entropy changes of RERhIn for RE = Tb and Dy are several times higher than those observed in their Pd- and Pt-based analogues. This is not surprising as the critical temperatures of magnetic ordering for RERhIn (RE = Tb, Dy) are remarkably smaller than those of RETIn (RE = Tb, Dy; T = Pd, Pt).
Figure 7. Magnetic entropy change vs. temperature as derived from data shown in Figure 6 under magnetic flux density changes up to 0-9 T for RERhIn: (a) RE = Gd, (b) RE = Tb, (c) RE = Dy, (d) RE = Ho (e) RE = Er, and (f) RE = Tm.
Smaller critical temperature leads to significant magnetization change occurring in a narrower temperature range and therefore maximizing both and (see Eq. (2)). The same phenomenon explains the big differences in the values for GdRhIn and GdPtIn as well as for DyRhIn and DyNiIn (see Table III). The values for RERhIn (RE = Ho, Er and Tm) are found to be higher than those of their Ni-, Pd- and Pt-based analogues, indicating stronger magnetization vs. temperature dependences in the Rh-based compounds. The magnetic entropy changes found for (RE = Gd-Tm) are sizeable and comparable with those reported for other rare-earth-based compounds with good magnetocaloric performance (see Table III). (RE = Gd-Tm) are therefore good candidates for application in low-temperature refrigeration techniques based on adiabatic demagnetization.
An inverse MCE, which manifests itself in negative values of , is found at low temperatures and low values of magnetic flux density change for selected (RE = Gd-Tm) intermetallics (see Figure 7). Inverse MCE originates from the antiferromagnetic component of the magnetic structure, which is suppressed by increasing temperature and/or increasing applied magnetic field. The inverse MCE is not observed for . This result is consistent with the magnetic data reported in section IV A, as has predominantly ferromagnetic character.
The temperature-averaged magnetic entropy change (TEC) is a parameter reporting how magnetic entropy change is maintained over a selected temperature span [74]. TEC is calculated using the following formula:
where is the center temperature of the temperature span . The value is determined by finding the one that maximizes the integral in Eq. (3).
The TEC values calculated for 3, 5 and 10 K temperature spans for (RE = Gd–Tm) are presented in Figure 8. Within the 3 K span and magnetic flux density change of 0-9 T, TEC reaches 12.3 J·kg·K (RE = Gd), 11.3 J·kg·K (RE = Tb), 13.4 J·kg·K (RE = Dy), 16.5 J·kg·K (RE = Ho), 15.2 J·kg·K (RE = Er) and 12.6 J·kg·K (RE = Tm), respectively. These values are quite close to the respective values of (see Table III). TEC tends to decrease with increasing temperature span . This effect is especially noticeable for the span of 10 K in the case of RE = Er and Tm. This is because (RE = Er, Tm) have the lowest critical temperatures of magnetic ordering (see Table II) and therefore the narrowest maxima in the dependences (see Figure 7). However, it has to be mentioned that even in case of RE = Er and Tm, the values of TEC(10 K) reach not less than 80 % of the corresponding values of (see Figure 8), indicating that the magnetocaloric performance over the temperature interval of 10 K is well maintened.
Figure 8. The maximum magnetic entropy change and temperature-averaged magnetic entropy change (TEC) of 3 K, 5 K, and 10 K plotted against magnetic flux density change for RERhIn: (a) RE = Gd, (b) RE = Tb, (c) RE = Dy, (d) RE = Ho, (e) RE = Er, and (f) RE = Tm.
Relative Cooling Power (RCP) and Refrigerant Capacity (RC)
Besides and TEC, there are two more parameters used to describe magnetocaloric performance of a given material. These are the relative cooling power (RCP) [75] and refrigerant capacity (RC) [76]. Both parameters correspond to the amount of heat transfer between the cold and hot reservoirs in an ideal refrigeration cycle [77]. RCP is a product of maximum magnetic entropy change and the full width at half maximum in the curve:
While RC is numerically calculated by integrating the area under the curve, taking the half maximum of the peak as the integration limits:
where and are the lower and upper limits of the FWHM temperature range, respectively.
Under magnetic flux density change of 0-9 T, the RCP and RC values are found to be 656 and 498 J·kg for RE = Gd, 442 and 340 J·kg for RE = Tb, 363 and 358 J·kg for RE = Dy, 522 and 407 J·kg for RE = Ho, 437 and 335 J·kg for RE = Er and 307 and 238 J·kg for RE = Tm. The values corresponding to other selected changes of magnetic flux density can be found in Table III.
Summary of magnetocaloric performance of (RE = Gd-Tm)
Table 3 presents a number of parameters characterizing magnetocaloric performance of (RE = Gd-Tm), including the temperature at which the maximum of magnetic entropy change is reached, together with the values of , RCP and RC under magnetic flux density changes of 0-2, 0-5, 0-7 and 0-9 T. For comparison, the parameters for the isostructural (T = Ni, Pd, Pt) intermetallics, as well as selected well-performing rare-earth-based compounds are also included.
| Materials | Temp. for [K] | \multicolumn{4}{c}{ [J·kg·K]} | \multicolumn{4}{c}{RCP [J·kg]} | \multicolumn{4}{c}{RC [J·kg]} | Ref. | |||||||||
| DyNiIn | 103 | 1.8 | 3.6 | 4.7 | - | 49 | 178 | 286 | - | 37 | 130 | 209 | - | [52] |
| HoNiIn | 19 | 2.6 | 7.1 | 10.1 | - | 84 | 298 | 458 | - | 66 | 234 | 352 | - | [52] |
| ErNiIn | 20 | 3.3 | 7.7 | 10.2 | - | 71 | 248 | 377 | - | 52 | 180 | 273 | - | [52] |
| GdRhIn | 17 | 3.8 | 7.9 | 10.3 | 12.4 | 87 | 265 | 443 | 656 | 68 | 205 | 329 | 498 | this work |
| TbRhIn | 28 | 3.5 | 7.2 | 9.6 | 11.3 | 34 | 199 | 315 | 442 | 26 | 161 | 246 | 340 | this work |
| DyRhIn | 19 | 2.2 | 8.1 | 10.0 | 13.1 | 49 | 195 | 316 | 363 | 36 | 150 | 241 | 358 | this work |
| HoRhIn | 12 | 3.7 | 10.7 | 13.9 | 16.4 | 53 | 227 | 368 | 522 | 40 | 176 | 287 | 407 | this work |
| ErRhIn | 8 | 4.4 | 11.1 | 13.7 | 15.3 | 49 | 191 | 311 | 437 | 36 | 147 | 236 | 335 | this work |
| TmRhIn | 6.5 | 4.0 | 9.7 | 11.5 | 12.6 | 37 | 146 | 225 | 307 | 28 | 112 | 174 | 238 | this work |
| TbPdIn | 62, 102 | 0.8 | 1.8 | 2.5 | 3.3 | 53 | 161 | 258 | 377 | 44 | 133 | 215 | 312 | [60] |
| DyPdIn | 22, 94 | 1.1 | 3.2 | 5.2 | 7.0 | 100 | 314 | 498 | 672 | 65 | 216 | 325 | 406 | [60] |
| HoPdIn | 22 | 2.5 | 7.2 | 10.0 | 12.6 | 94 | 326 | 489 | 661 | 81 | 269 | 403 | 541 | [60] |
| ErPdIn | 17 | 3.3 | 7.7 | 10.1 | 12.1 | 103 | 287 | 403 | 528 | 91 | 227 | 314 | 409 | [60] |
| TmPdIn | 9 | 4.4 | 9.2 | 10.8 | 11.9 | 85 | 156 | 234 | 320 | 50 | 123 | 184 | 249 | [60] |
| GdPtIn | 78 | 1.0 | 2.2 | 3.0 | 3.7 | 58 | 172 | 261 | 359 | 48 | 139 | 209 | 290 | [58] |
| TbPtIn | 45, 110 | 0.8 | 1.7 | 2.5 | 3.4 | 82 | 198 | 303 | 428 | 57 | 165 | 248 | 340 | [58] |
| DyPtIn | 25, 95 | 1.1 | 2.9 | 4.7 | 6.3 | 45 | 290 | 250 | 363 | 33 | 201 | 180 | 263 | [58] |
| HoPtIn | 23 | 2.5 | 6.9 | 9.5 | 11.8 | 94 | 302 | 451 | 607 | 82 | 254 | 373 | 495 | [58] |
| ErPtIn | 14 | 3.6 | 7.5 | 9.6 | 11.4 | 79 | 218 | 328 | 434 | 63 | 175 | 256 | 341 | [58] |
| TmPtIn | 8 | 3.2 | 7.7 | 9.2 | 10.2 | 34 | 125 | 189 | 260 | 27 | 98 | 150 | 205 | [58] |
| GdNiIn | 98 | 1.4 | 2.9 | 3.6 | - | 54 | 171 | 269 | - | 38 | 131 | 206 | - | [78] |
| DyNiIn | 19, 92 | 0.8 | 3.8 | 6.0 | - | 21 | 109 | 195 | - | 16 | 81 | 145 | - | [78] |
| HoNiIn | 16 | 1.8 | 8.8 | 12.4 | - | 32 | 198 | 353 | - | 24 | 152 | 269 | - | [78] |
| GdIn | 194 | 2.8 | - | - | - | - | - | - | - | - | - | - | - | [5] |
| TbIn | 165 | 3.5 | 6.6 | - | - | 200 | 660 | - | - | - | - | - | - | [6] |
| DyIn | 130 | 4.6 | 9.2 | - | - | 230 | 736 | - | - | - | 545 | - | - | [11] |
| DyIn | 125 | - | - | 8.8 | - | - | - | - | - | - | - | - | - | [39] |
| HoIn | 85 | 5.0 | 11.2 | - | - | 125 | 560 | - | - | - | 360 | - | - | [6, 7] |
| ErIn | 46 | 7.9 | 16.0 | - | - | - | - | - | - | - | 490 | - | - | [8] |
| GdPt | 28 | 1.7 | - | 6.2 | - | - | - | - | - | - | - | - | - | [9] |
| DyPt | 10.4 | 5 | 9.2 | 11.4 | - | - | - | - | - | 50 | 150 | - | - | [40] |
| GdRhIn | 30 | - | 8 | 10.3 | - | - | - | - | - | 80 | 282 | - | - | [41] |
| GdRh | 24 | 13 | 22 | - | - | - | 534 | - | - | - | - | - | - | [79] |
| GdRh | 112 | 5 | 9.2 | - | - | 143 | 473 | - | - | - | - | - | - | [80] |
| TbRh | 94 | 11.6 | 17.9 | 21 | - | 226 | 594 | - | - | - | - | - | - | [42] |
| HoRh | 35 | - | 10 | - | - | - | - | - | - | - | 320 | - | - | [43] |
| GdRh | 16 | 5 | 14 | - | - | - | 374 | - | - | - | - | - | - | [79] |
Table 3. TABLE III. The temperature for maximum entropy changes, maximum entropy changes , RCP and RC values under magnetic flux density changes of 0–2 T, 0–5 T, 0–7 T, and 0–9 T for RERhIn (RE = Gd–Tm) and selected rare-earth-based compounds. –1 T | –8 T
In terms of maximum magnetic entropy change (), (RE = Gd-Tm) have the best magnetocaloric performance when compared to their isostructural (T = Ni, Pd, Pt) analogues. The magnetocaloric performance of (RE = Gd-Tm) is comparable to the performance of other well-performing rare-earth-based compounds, whose selected representatives are included in Table III.
The temperatures at which maximum magnetic entropy change reaches its maximum vary for (RE = Gd-Tm) from 6.5 K (RE = Tm) up to 28 K (RE = Tb). Combining different RERhIn intermetallics makes it possible to create a hybrid material showing good magnetocaloric performance from the liquid helium temperature up to about 30 K. Moreover, combining selected RERhIn (RE = Gd-Tm) compounds with the ones well-performing at higher temperatures (see selected representatives listed in Table III) enables creating a material showing good magnetocaloric performance from the liquid helium temperature up to the temperature of liquid nitrogen. Therefore, RERhIn (RE = Gd-Tm) intermetallics, investigated in this work, are good candidates for application in low-temperature refrigeration.
Conclusions
The RERhIn (RE = Gd-Tm) intermetallics crystallize in the orthorhombic LuNiIn-type crystal structure with the rare earth atoms occupying three non-equivalent Wyckoff sites. The compounds order magnetically, with the critical temperatures of magnetic ordering ranging from 4.9 K (RE = Tm) up to 15.4 K (RE = Dy). The materials show complex magnetic properties indicating features characteristic of both ferro- and antiferromagnetic orderings. The character of magnetic ordering changes with increasing number of the 4f electrons from predominantly ferromagnetic in GdRhIn to predominantly antiferromagnetic in TmRhIn. The investigated compounds show at low temperatures quite good magnetocaloric performance, comparable to that found in other well-performing rare-earth-based compounds. Therefore, RERhIn (RE = Gd-Tm) are good candidates for application in low-temperature refrigeration based on the adiabatic demagnetization technique.
Declaration of Competing Interest
The authors declare no conflict of interest.
Acknowledgements
The study was funded by “Research support module” as part of the “Excellence Initiative – Research University” program at the Jagiellonian University in Kraków.
The research was carried out with the equipment purchased thanks to the financial support of the European Regional Development Fund in the framework of the Polish Innovation Economy Operational Program (contract no.POIG.02.01.00-12-023/08).
References
References
- [1]S. Gupta, K. Suresh, Review on magnetic and related properties of RTX compounds, Journal of Alloys and Compounds 618 (2015) 562–606. doi: 10.1016/j.jallcom.2014.08.079DOI
- [2]J. C. Patiño, N. de Oliveira, Magnetocaloric effect in R₂Cu₂Cd (R = Gd, Tb, Er, Tm), Physica B: Condensed Matter 650 (2023) 414496. doi: 10.1016/j.physb.2022.414496.DOI
- [3]L. Li, M. Yan, Recent progresses in exploring the rare earth based intermetallic compounds for cryogenic magnetic refrigeration, Journal of Alloys and Compounds 823 (2020) 153810. doi:10.1016/j.jallcom.2020.153810.DOI
- [4]D. Guo, L. M. Moreno-Ramírez, C. Romero-Muñiz, Y. Zhang, J.-Y. Law, V. Franco, J. Wang, Z. Ren, Recent progresses in exploring the rare earth based intermetallic compounds for cryogenic magnetic refrigeration, Science China Materials 64 (2021) 2846–2857. doi: 10.1007/s40843-021-1711-5.
- [5]A. Bhattacharyya, S. Giri, S. Majumdar, Field induced sign reversal of magnetocaloric effect in Gd₂In, Journal of Magnetism and Magnetic Materials 324 (2012) 1239–1241. doi:10.1016/j.jmmm.2011.11.023.DOI
- [6]Q. Zhang, J. Cho, J. Du, F. Yang, X. Liu, W. Feng, Y. Zhang, J. Li, Z. Zhang, Large reversible magnetocaloric effect in Tb₂In, Solid State Communications 149 (2009) 396–399. doi:10.1016/j.ssc.2008.12.009.DOI
- [7]Q. Zhang, J. H. Cho, B. Li, W. J. Hu, Z. D. Zhang, Magnetocaloric effect in Ho₂In over a wide temperature range, Applied Physics Letters 94 (2009) 182501. doi: 10.1063/1.3130090.DOI
- [8]H. Zhang, B. Shen, Z. Xu, J. Chen, J. Shen, F. Hu, J. Sun, Large reversible magnetocaloric effect in Er₂In compound, Journal of Alloys and Compounds 509 (2011) 2602–2605. doi:10.1016/j.jallcom.2010.11.108.DOI
- [9]T. Samanta, I. Das, Negligible influence of domain walls on the magnetocaloric effect in GdPt₂, Phys. Rev. B 74 (2006) 132405. doi:10.1103/PhysRevB.74.132405.DOI
- [10]S. Taskaev, V. Khovaylo, K. Skokov, W. Liu, E. Bykov, M. Ulyanov, D. Bataev, A. Basharova, M. Kononova, D. Plakhotksiy, M. Bogush, T. Gottschall, O. Gutfleisch, Magnetocaloric effect in GdNi₂ for cryogenic gas liquefaction studied in magnetic fields up to 50 T, Journal of Applied Physics 127 (2020) 233906. doi:10.1063/5.0006281.DOI
- [11]Q. Zhang, X. G. Liu, F. Yang, W. J. Feng, X. G. Zhao, D. J. Kang, Z. D. Zhang, Large reversible magnetocaloric effect in Dy₂In, Journal of Physics D: Applied Physics 42 (2009) 055011. doi:10.1088/0022-3727/42/5/055011.DOI
- [12]M. de Souza, Investigation on the magnetocaloric effect in RNi₂ (R: Dy, Tb) melt-spun ribbon, Journal of Magnetism and Magnetic Materials 412 (2016) 11–14. doi: 10.1016/j.jmmm.2016.03.078.
- [13]J. Ćwik, Y. Koshkid’ko, K. Nenkov, E. Tereshina, K. Rogacki, Structural, magnetic and magnetocaloric properties of HoNi₂ and ErNi₂ compounds ordered at low temperatures, Journal of Alloys and Compounds 735 (2018) 1088–1095. doi:10.1016/j.jallcom.2017.11.194.
- [14]S. Baran, Y. Tyvanchuk, B. Penc, Y. Kalychak, A. Hoser, A. Szytuła, Crystal structure and complex magnetic properties of R₁₁Pd₄In₉ compounds (R = Y, Gd–Er), Intermetallics 123 (2020) 106837. doi: 10.1016/j.intermet.2020.106837.DOI
- [15]K. Matsumoto, T. Kouen, R. Nishida, S. Abe, K. Kamiya, T. Numazawa, Magnetocaloric Effect of RCo₂ (R: Er, Ho, Dy) Compounds for Regenerative Magnetic Refrigeration, AIP Conference Proceedings 850 (2006) 1581–1582. doi:10.1063/1.2355310.DOI
- [16]S. Ma, W. B. Cui, D. Li, N. K. Sun, D. Y. Geng, X. Jiang, Z. D. Zhang, Large cryogenic magnetocaloric effect of DyCo₂ nanoparticles without encapsulation, Applied Physics Letters 92 (2008) 173113. doi:10.1063/1.2919079.DOI
- [17]R. Rajivgandhi, J. Rajesh Krishna, J. Arout Chelvane, S. Quezado, S. Malik, R. Nirmala, Magnetocaloric effect in melt-spun laves phase intermetallic compound HoCo₂, Journal of Magnetism and Magnetic Materials 448 (2018) 351–354. doi:10.1016/j.jmmm.2017.08.004, international Conference on Magnetic Materials and Applications – IC-MAGMA2017.DOI
- [18]S. Nikitin, A. Tishin, Magnetocaloric effect in HoCo₂ compound, Cryogenics 31 (1991) 166–167. doi: 10.1016/0011-2275(91)90171-R.DOI
- [19]Z. Jun-Ding, S. Bao-Gen, S. Ji-Rong, Magnetocaloric effect in ErCo₂ compound, Chinese Physics 16 (2007) 1817. doi:10.1088/1009-1963/16/7/001.
- [20]H. Wada, T. Sometakawa, M. Shiga, Magnetocaloric effect of ErCo₂, Journal of Magnetism and Magnetic Materials 196-197 (1999) 689–690. doi:10.1016/S0304-8853(98)00894-4.DOI
- [21]E. Burzo, I. Pop, D. Kozlenko, Magnetic and magnetocaloric properties of some ferrimagnetic compounds, Journal of Optoelectronics and Advanced Materials – Rapid Communications 12 (2010) 1105–1113.
- [22]N. K. Singh, K. Suresh, A. Nigam, S. Malik, A. Coelho, S. Gama, Itinerant electron metamagnetism and magnetocaloric effect in RCo₂-based laves phase compounds, Journal of Magnetism and Magnetic Materials 317 (2007) 68–79. doi:10.1016/j.jmmm.2007.04.009.DOI
- [23]N. Duc, D. Anh, Magnetocaloric effects in RCo₂ compounds, Journal of Magnetism and Magnetic Materials 242-245 (2002) 873–875. doi:10.1016/S0304-8853(01)01328-2, proceedings of the Joint European Magnetic Symposia (JEMS’01).DOI
- [24]T. Samanta, I. Das, S. Banerjee, Magnetocaloric effect in Ho₅Pd₂ : Evidence of large cooling power, Applied Physics Letters 91 (8) (2006) 1–3. doi:10.1063/1.2775050.DOI
- [25]T. Paramanik, T. Samanta, R. Ranganathan, I. Das, Magnetic and magnetocaloric properties of Dy₅Pd₂: role of magnetic irreversibility, RSC Adv. 5 (2015) 47860–47865. doi:10.1039/C5RA06970J.
- [26]B. Maji, M. K. Ray, M. Modak, S. Mondal, K. Suresh, S. Banerjee, Magnetic properties and large reversible magnetocaloric effect in Er₃Pd₂, Journal of Magnetism and Magnetic Materials 456 (2018) 236–240. doi: 10.1016/j.jmmm.2018.02.036.DOI
- [27]X. Wu, C. Guo, J. Wang, J. Deng, Y. Du, G. Rao, Z. Du, Magnetic properties and large magnetocaloric effect in Ho₃Pd₂ compound, Journal of Magnetism and Magnetic Materials 482 (2019) 168–172. doi: 10.1016/j.jmmm.2019.03.048.DOI
- [28]R. Rawat, I. Das, Heat capacity and magnetocaloric studies of RPd₂Si (R = Gd, Tb and Dy), Journal of Physics: Condensed Matter 18 (2006) 1051. doi: 10.1088/0953-8984/18/3/020.DOI
- [29]R. Rawat, I. Das, Magnetocaloric and magnetoresistance studies of GdPd₂Si, Journal of Physics: Condensed Matter 13 (2001) L57. doi:10.1088/0953-8984/13/3/102.DOI
- [30]B. Sahu, R. D. Fabossa, B. M. Sondezi, A. M. Strydom, Large magnetocaloric effect in Ho₂Pd₂Pb, Materials Today Communications 31 (2022) 103327. doi: 10.1016/j.mtcomm.2022.103327.DOI
- [31]H. Zhang, B.-G. Shen, Magnetocaloric effects in RTX intermetallic compounds (R = Gd-Tm, T = Fe-Cu and Pd, X = Al and Si)* Chinese Physics B 24 (2015) 127504. doi:10.1088/1674-1056/24/12/127504.
- [32]Z.-J. Mo, J. Shen, X.-Q. Gao, Y. Liu, J.-F. Wu, B.-G. Shen, J.-R. Sun, Magnetic properties and magnetocaloric effects in HoPd intermetallic*, Chinese Physics B 24 (2015) 037503. doi:10.1088/1674-1056/24/3/037503.DOI
- [33]J. Huo, Y. Du, G. Cheng, X. Wu, L. Ma, J. Wang, Z. Xia, G. Rao, Magnetic properties and large magnetocaloric effects of GdPd intermetallic compound, Journal of Rare Earths 36 (2018) 1044–1049. doi:10.1016/j.jre.2018.03.016.DOI
- [34]J. Shen, Z.-Y. Xu, H. Zhang, X.-Q. Zheng, J.-F. Wu, F.-X. Hu, J.-R. Sun, B. gen Shen, Metamagnetic transition and magnetocaloric effect in antiferromagnetic TbPdAl compound, Journal of Magnetism and Magnetic Materials 323 (2011) 2949–2952. doi:10.1016/j.jmmm.2011.05.042.DOI
- [35]Z. Xu, B. Shen, Large magnetocaloric effect in metamagnetic HoPdAl, Sci. China Technol. Sci. 55 (2012) 45–450. doi:10.1007/s11431-011-4681-9.DOI
- [36]M. K. Sharma, K. Yadav, K. Mukherjee, Complex magnetic behaviour and evidence of a superspin glass state in the binary intermetallic compound Er5Pd2, Journal of Physics: Condensed Matter 30 (2018) 215803. doi:10.1088/1361-648X/aabbfe.DOI
- [37]M. K. Sharma, K. Mukherjee, Evidence of large magnetic cooling power and double glass transition in Tb5Pd2, Journal of Magnetism and Magnetic Materials 466 (2018) 317–322. doi:10.1016/j.jmmm.2018.07.029.DOI
- [38]M. K. Sharma, K. Mukherjee, Field induced nature and nonlinear DC susceptibility studies of Ni substituted Dy5Pd2 cluster glass system, Physica B: Condensed Matter 572 (2019) 56–59. doi:10.1016/j.physb.2019.07.053.DOI
- [39]G. Yao, F. Wei, J. Zhang, X. Fan, X. Yin, W. Cui, Q. Wang, The enhanced magnetocaloric effect in Dy2In1−xAlx by a non-hysteresis metamagnetic phase transition, Scripta Materialia 167 (2019) 37–40. doi:10.1016/j.scriptamat.2019.03.029.DOI
- [40]P. Arora, M. K. Chattopadhyay, S. B. Roy, Magnetic properties and large magnetocaloric effect of DyPt2, Journal of Applied Physics 106 (2009) 093912. doi:10.1063/1.3253729.DOI
- [41]R. Kumar, A. A. Maz, S. K. Mishra, S. Gupta, Structural, Magnetic, and Magneto-Thermal Properties of Rare Earth Intermetallic GdRhIn, Sensors 24 (2024) 6326. doi:10.3390/s24196326.DOI
- [42]E. Talik, M. Klimczak, Giant magnetocaloric effect in Tb3Rh, Journal of Alloys and Compounds 486 (2009) L30–L33. doi:10.1016/j.jallcom.2009.07.159.DOI
- [43]Y. Shang, Y. Yuan, Y. Cao, R. Hadimani, Y. Mozharivskyj, H. Fu, Structure, magnetic properties, and magnetocaloric effect of polycrystalline Ho3M (M = Rh, Ru) alloys, Journal of Magnetism and Magnetic Materials 497 (2020) 166055. doi:10.1016/j.jmmm.2019.166055.DOI
- [44]P. von Ranke, N. de Oliveira, M. Tovar Costa, E. Nobrega, A. Caldas, I. de Oliveira, The influence of crystalline electric field on the magnetocaloric effect in the series RAl2 (R = Pr, Nd, Tb, Dy, Ho, Er, and Tm), Journal of Magnetism and Magnetic Materials 226–230 (2001) 970–972. doi:10.1016/S0304-8853(00)01162-8, proceedings of the International Conference on Magnetism (ICM 2000).
- [45]S. Zhen, X. Zheng, D. Wang, Y. Gao, H. Liu, Y. Pan, L. Xi, G. Wang, Z. Zhang, G. Zhang, A. Ma, Z. Chen, J. Xu, S. Wang, B. Shen, Large magnetocaloric effect of RCoSn (R=Dy, Ho, Er and Tm) compounds, Journal of Alloys and Compounds 1005 (2024) 176251. doi:10.1016/j.jallcom.2024.176251.DOI
- [46]V. I. Zaremba, Ya. M. Kalychak, P. Yu. Zavalii, V. A. Bruskov, Crystal structures of the compounds R5Ni2In4 (R = Ho, Er, Tm, Lu), Kristallografiya 36 (1991) 1415–1418.
- [47]R. Zaremba, W. Hermes, M. Eul, R. Pöttgen, Rare Earth-Transition Metal Indides with Lu5Ni2In4-type Structure, Z. Naturforsch. 63b (2008) 1447–1449.DOI
- [48]L. Sojka, M. Dashkevych, B. Belan, M. Manyako, V. Davydov, L. Akselrud, Ya. M. Kalychak, Crystal structure of alloys R5Pd2In4 (R = Y, Tb, Dy, Ho, Er, Tm, Lu), Ukr. Chem. J. 74 (2008) 90–94.
- [49]R. Zaremba, Ute Ch. Rodewald, R. Pöttgen, Rare Earth-Rich Indides RE5Pt2In4 (RE = Sc, Y, La–Nd, Sm, Gd–Tm, Lu), Monatshefte fur Chemie 138 (2007) 819–822. doi:10.1007/s00706-007-0702-6.DOI
- [50]C. Ritter, A. Provino, P. Manfrinetti, V. K. Pecharsky, K. A. Gschneidner, S. K. Dhar, Magnetic structures of R5Ni2In4 and R11Ni4In9 (R = Tb and Ho): strong hierarchy in the temperature dependence of the magnetic ordering in the multiple rare-earth sublattices, Journal of Physics: Condensed Matter 27 (2015) 476001. doi:10.1088/0953-8984/27/47/476001.DOI
- [51]A. Provino, Y. Mudryk, D. Paudyal, P. V. Smetana, V. K. Pecharsky, K. A. Gschneidner, Jr., J. D. Corbett, Crystal structure of Tb5Ni2In4 and Y5Ni2In4, and magnetic properties of Dy5Ni2In4, J. Appl. Phys. 111 (2012) 07E122. doi:10.1063/1.3673432.DOI
- [52]Z. Zhang, X. Dong, Q. Wang, L. Li, Investigation of the crystal structure, magnetic phase transition and magnetocaloric effect in RE5Ni2In4 (RE = Dy, Ho and Er) compounds, Intermetallics 100 (2018) 136–141. doi:10.1016/j.intermet.2018.06.012.
- [53]Yu. B. Tyvanchuk, B. Penc, A. Szytula, A. Zarzycki, Magnetic Properties of Ho5Ni2In4, Acta Phys. Pol. A 117 (2010) 599–600. doi:10.12693/APhysPolA.117.599.DOI
- [54]Ł. Gondek, J. Przewoźnik, J. Czub, Yu. Tyvanchuk, A. Szytula, A. Arrulaj, Crystal and magnetic properties of Er5Ni2In4 at low temperatures, Intermetallics 21 (2012) 10–17. doi:10.1016/j.intermet.2011.09.007.DOI
- [55]A. Szytula, Yu. Tyvanchuk, S. Baran, J. Przewoźnik, Ya. M. Kalychak, Magnetic and thermal properties of Tm5Ni2In4, Intermetallics 43 (2013) 99–102. doi:10.1016/j.intermet.2013.07.014.DOI
- [56]A. Szytula, S. Baran, D. Kaczorowski, W. Sikora, A. Hoser, Magnetic ordering in Tm5Ni2In4, Journal of Alloys and Compounds 617 (2014) 149–153. doi:10.1016/j.jallcom.2014.07.190.
- [57]S. Baran, A. Deptuch, M. Reehuis, Y. Tyvanchuk, F. Yokaichiya, A. Szytula, Complex magnetic ordering in RE5Pd2In4 (RE = Tb–Tm) compounds investigated by neutron diffraction and magnetometric measurements, Journal of Alloys and Compounds 877 (2021) 160171. doi:10.1016/j.jallcom.2021.160171.DOI
- [58]A. R. Hayyu, S. Baran, A. Szytula, K. Berent, A. Deptuch, Characterization of magnetic properties, including magnetocaloric effect, of RE5Pt2In4 (RE = Gd–Tm) compounds, Journal of Alloys and Compounds 1001 (2024) 175054. doi:10.1016/j.jallcom.2024.175054.DOI
- [59]A. Deptuch, S. Baran, L. Keller, A. R. Hayyu, A. Szy- tula, Magnetic structures in R₅Pt₂In₄ (R = Tb–Tm) investigated by neutron powder diffraction, Acta Crystallographica Section B 80 (2024) 281–293. doi: 10.1107/S2052520624004451.
- [60]A. R. Hayyu, S. Baran, A. Sztyła, Magnetocaloric properties of RE₅Pd₂In₄ (RE = Tb–Tm) compounds with multiple magnetic sublattices, Physica B: Condensed Matter 710 (2025) 417184. doi: 10.1016/j.physb.2025.417184.DOI
- [61]J. Rodríguez-Carvajal, Recent advances in magnetic structure determination by neutron powder diffraction, Physica B 192 (1993) 55–69. doi:10.1016/0921-4526(93)90108-1.
- [62]J. Rodríguez-Carvajal, Recent developments of the program fullprof, Newsletter of the Commission for Powder Diffraction of the IUCr 26 (2001) 12–19.
- [63]C. Kittel, Introduction to Solid State Physics, 8th ed., John Wiley and Sons, New Jersey, America, 2004.
- [64]S. Mugiraneza, A. Hallas, Tutorial: a beginner’s guide to interpreting magnetic susceptibility data with the curie-weiss law, Commun Phys 5 (2022) 1–12. doi: 10.1038/s42005-022-00853-y.DOI
- [65]P. G. De Gennes, Interactions indirectes entre couches 4f dans les métaux de terres rares, J. Phys. Radium 23 (1962) 510–521. doi:10.1051/jphysrad:01962002308-9051001.
- [66]D. Noakes, G. Shenoy, The effect of a crystalline electric field on the magnetic transition temperatures of rare-earth rhodium borides, Physics Letters A 91 (1982) 35–36. doi:10.1016/0375-9601(82)90258-4.DOI
- [67]S. Shafiq, A. Hussain, M. N. Rasul, S. S. Hayat, F. Iqbal, M. A. Rafiq, First-principles structural, electronic, optical and bonding properties of scandium-based ternary indide system Sc₅T₂In₄ (T = Ni, Pd, Pt), Bulletin of Materials Science 43 (2020) 284. doi:10.1007/s12034-020-02251-y.
- [68]J. Kusz, H. Böhm, E. Talik, X-ray investigation and discussion of the magnetostriction of Gd₃T (T = Ni, Rh, Irₓ) single crystals, Journal of Applied Crystallography 33 (2000) 213–217. doi:10.1107/S0021889899014922.
- [69]E. Talik, A. Ślebarski, Properties of Gd₃T compounds (T = Rh, Ir, Pd), Journal of Alloys and Compounds 223 (1995) 87–90. doi:10.1016/0925-8388(94)01487-6.DOI
- [70]E. Talik, M. Neumann, Spin fluctuations in the R₃T compounds (R = Gd, T = Ir, Rh), Journal of Magnetism and Magnetic Materials 140-144 (1995) 795–796 doi:10.1016/0304-8853(94)01475-2, International Conference on Magnetism.DOI
- [71]E. Talik, M. Neumann, T. Mydlarz, Photoemission study and magnetization of Gd₃Pd₂ intermetallic compound, Journal of Magnetism and Magnetic Materials 189 (1998) 183–188. doi:10.1016/S0304-8853(98)00245-5.
- [72]A. Sztyła, A. Jezierski, B. Penc, Electronic structure and magnetism of rare-earth intermetallic compounds, Physica B: Condensed Matter 327 (2003) 171–176. doi:10.1016/S0921-4526(02)01720-9, proceedings of the International Symposium on Advanced Magnetic Materials.
- [73]A. M. Tishin, Y. I. Spichkin, The Magnetocaloric Effect and its Applications, Institute of Physics Publishing, Bristol and Philadelphia, 2003.
- [74]L. D. Griffith, Y. Mudryk, J. Slaughter, V. K. Pecharsky, Material-based figure of merit for caloric materials, J. Appl. Phys. 123 (2018) 034902. doi:10.1063/1.5004173.DOI
- [75]K. A. Gschneidner, Jr., V. K. Pecharsky, Magnetocaloric materials, Annu. Rev. Mater. Sci. 30 (2000) 387–429. doi:10.1146/annurev.matsci.30.1.387.DOI
- [76]M. E. Wood, W. H. Potter, General analysis of magnetic refrigeration and its optimization using a new concept: maximization of refrigerant capacity, Cryogenics 25 (1985) 667–683. doi:10.1016/0011-2275(85)90187-0.DOI
- [77]L.-W. Li, Review of magnetic properties and magnetocaloric effect in the intermetallic compounds of rare earth with low boiling point metals*, Chinese Physics B 25 (2016) 037502. doi:10.1088/1674-1056/25/3/037502.DOI
- [78]Z. Zhang, P. Wang, Y. Jia, X. Wang, L. Li, Crystal structure, magnetic phase transitions and magnetocaloric effect (MCE) in layer-like RE₁₁Ni₁₁In₉ (RE = Gd, Dy and Ho) compounds, Journal of Alloys and Compounds 851 (2021) 155863. doi:10.1016/j.jallcom.2020.155863.
- [79]C. L. Wang, J. D. Zou, J. Liu, Y. Mudryk, J. Gschneidner, K. A., Y. Long, V. Smetana, G. J. Miller, V. K. Pecharsky, Crystal structure, magnetic properties, and the magnetocaloric effect of Gd₅Rh₄ and GdRh₂, Journal of Applied Physics 113 (2013) 17A904. doi:10.1063/1.4793775.
- [80]P. Kumar, K. G. Suresh, A. K. Nigam, Magnetothermal effect in Gd₃Rh, Journal of Applied Physics 109 (2011) 07A909. doi:10.1063/1.3540664.DOI




