betaFeedback

WorksPhysics and Astronomy

Fundamental Antisymmetric Mode Acoustic Resonator in Periodically Poled Piezoelectric Film Lithium Niobate

Abstract

Radio frequency (RF) acoustic resonators have long been used for signal processing and sensing. Devices that integrate acoustic resonators benefit from their slow phase velocity (vp), in the order of 3 to 10 km/s, which allows miniaturization of the device. Regarding the subject of small form factor, acoustic resonators that operate at the so-called fundamental antisymmetric mode (A0), feature even slower vp (1 to 3 km/s), which allows for smaller devices. This work reports the design and fabrication of A0 mode resonators leveraging the advantages of periodically poled piezoelectricity (P3F) lithium niobate, which includes a pair of piezoelectric layers with opposite polarizations to mitigate the charge cancellation arising from opposite stress of A0 in the top and bottom piezoelectric layers. The fabricated device shows a quality factor (Q) of 800 and an electromechanical coupling (k2) of 3.29, resulting in a high figure of merit (FoM, Q times k2) of 26.3 at the resonant frequency of 294 MHz, demonstrating the first efficient A0 device in P3F platforms. The proposed A0 platform could enable miniature signal processing, sensing, and ultrasound transducer applications upon optimization.

Introduction

There is a never-ending demand for smaller devices in the radio-frequency (RF) commercial electronics industry. Not only are small form factor devices required, but the performance of the components is expected to remain comparable. To this end, acoustic wave resonators have achieved great success in applications such as miniature sensors, high quality factor (QQ) resonators and front-end filters for mobile applications [1], [2]. Acoustic resonators utilize the principle of piezoelectricity to transduce energy back and forth between electrical signals and mechanical oscillations. Therefore, it is possible to perform the sensing or signal processing in the mechanical domain, which has the advantage of slow phase velocities (vpv_p) in the order of 3 to 10 km/s, several orders of magnitude lower than the electrical counterparts [3], [4]. Among different types of acoustic vibrations, resonators working at the fundamental symmetric mode (S0) [5, 6, 7, 8], the fundamental shear horizontal mode (SH0) [9, 10, 11, 12, 13], first-order antisymmetric (A1) [14, 15, 16, 17, 18, 19], and first-order symmetric (S1) [20, 21, 22, 23, 24, 25, 26, 27] have been widely studied. Such devices have demonstrated strong potential and are still

heavily investigated. However, it is not easy to further tune down the vpv_p of these modes below 3 km/s. This factor limits the range of device size reduction. Another mode, namely the fundamental antisymmetric mode (A0), features even slower vpv_p of less than 2 km/s [28]. Thus, exciting this mode opens the possibility of further device dimensions downsizing. However, an efficient excitation of the A0 mode with high figures of merit is not trivial. In the case of a single film, due to the nature of the motion, stress antinodes with opposite signs develop at the top and bottom of the piezoelectric layer. This effect leads to charge cancellation, adversely affecting the achievable electromechanical coupling (k2k^2), thus lowering the figure of merit (FoM, Q⋅k2Q \cdot k^2). Adding a passivation silicon dioxed (SiO2) layer can partially mitigate this issue, but this process itself also brings about degraded k2k^2 and QQ [29], [30]. Recently, resonators leveraging the periodically poled piezoelectric (P3F) effect have been proposed to exploit over-moded lithium-niobate (LiNbO3) resonators [31, 32, 33]. moded resonators also suffer from charge cancellation effects, and P3F films have the potential to help mitigate the issues. However, studies on enhancing the performance of A0 mode device with P3F LiNbO3_3 are not reported.

In this work, we implemented the first A0 mode resonators in a P3F thin-film. The devices are built on a dual-layer X-cut LiNbO3_3 film, achieving a QQ of 800, k2k^2 of 3.29% and a high FoM of 23.6 at 294 MHz, while maintaining a vpv_p of 1800 m/s, 2 to 5 times smaller than S0 modes. The proposed A0 platform could enable miniature signal processing, sensing, and ultrasound transducer applications upon optimization.

Design and Simulation

The device structure is formed by 2 layers of X-cut LiNbO3_3, each layer with a thickness of 550 nm and the y-orientation in opposite direction Figure 1(a). The displacement and stress profiles for a canonical A0 shape motion are shown in Figure 1(b). The displacement is purely vertical and it has the characteristic flexural bending associated with the fundamental mode. The lateral stress antinodes, as expected, are at the top and bottom of the thin film and have opposite signs.

LiNbO3 dual layer resonator stack and simulated A0 displacement and stress profiles

Figure 1. (a) LiNbO3 dual layer resonator stack (b) Simulated A0 displacement and stress profiles.

In conventional single-layer piezoelectric materials, it is hard to harness the generated charge with a single pair of top electrodes, as the sign of charges in the upper and lower sections will perfectly cancel Figure 2(a). However, in P3F LiNbO3_3, due to the different signs in the piezoelectric coefficient (e11e_{11}), we will fully harness the piezoelectricity Figure 2(b).

Stress antinode formation in single layer A0 mode and fully harnessing piezoelectric conversion using P3F dual layer stack

Figure 2. (a) Stress antinode formation in single layer A0 mode leading to charge cancellation (b) Fully harnessing piezoelectric conversion using P3F dual layer stack.

The resonator is excited by aluminum (Al) interdigitated electrodes (IDT) sitting on top of the stack, the wavelength (λ\lambda) is chosen as 6 μm, and a constant duty cycle of 50% is maintained. The metal thickness is selected as 350 nm. A single unit cell of the proposed design was simulated using COMSOL finite element analysis (FEA) to verify the mode shape and the effect of the P3F film stack, the results are shown in Figure 3. The device exhibits an electromechanical coupling (k2k^2) of 6.34% at the resonant frequency of 283.4 MHz.

Simulated admittance curve and A0 flexural displacement mode shape

Figure 3. Simulated admittance of the unit cell resonator and A0 flexural displacement mode shape.

A comparison between k2k^2 and vpv_p against changes in the λ\lambda is plotted in Figure 4. It can be observed that at 6 μm the vpv_p is 1,800 m/s, thus confirming the potential of P3F resonators to realize miniaturized devices. Additionally, the intersection between k2k^2 and vpv_p also validates the selection of λ\lambda as it offers a good tradeoff between these 2 parameters.

Simulated k² and vₚ dispersion curves

Figure 4. Simulated k2k^2 and vpv_p dispersion curves against changes in the wavelength of a unit cell A0 resonator.

Fabrication and Measurement

The fabrication process starts with a dual layer X-cut LiNbO3_3, total thickness of 1.1 μm, thin film transferred on top of a silicon (Si) carrier wafer. The material stack is provided by NGK Insulators, Inc. First, opening windows for device release are patterned on top using traditional lithography techniques. Next, ion milling is used to etch through the LiNbO3_3 stack deep into the silicon wafer. Afterwards, the features for metal interconnects are patterned using electron beam lithography, and e-beam evaporation is used to deposit 350 nm of Al for the buslines and electrodes. Finally, the resonators are released using xenon difluoride (XeF2_2) for silicon etching. The step-by-step fabrication process is depicted in Figure 5(a). An optical image of the final suspended device is shown in Figure 5(b), the large lateral etch windows perform most of the isotropic release process, while the small etch windows between electrodes help confine acoustic energy in the active area.

Fabrication process diagram and optical image of the fabricated device

Figure 5. (a) Step-by-step fabrication process diagram of the A0 resonators (b) Optical image of the full fabricated device.

The fabricated device is measured using a Keysight vector network analyzer (VNA), and the measured data is then fitted using a modified Butterworth-Van Dyke model. The main resonance is located at 294 MHz, in good agreement with the expected behaviour from the simulation. The device exhibits a QQ of 800 and a k2k^2 of 3.29%, resulting in a high FoM of 26.3. The reduced k2k^2 is due to crystal orientation misalignment of the top and bottom layers during the bonding, which could be improved in future works. QQ could be potentially enhanced by minimizing lattice damage during thin film transfer. A possible approach to maintaining good lattice properties could involve using an intermediate amorphous silicon (a-Si) layer between the LiNbO3_3 stack and carrier substrate [34]. The measurements, fitting and extracted main parameters are plotted in Figure 6 (a) and (Figure 6b), respectively.

Measured and fitted response of the A0 resonator

Figure 6. (a) Measured and fitted response of the A0 resonator in (a) admittance and (b) phase.

Conclusion

In this work, we report the first A0 mode resonator leveraging a P3F X-cut LiNbO3_3 bi-layer stack. The device shows a QQ of 800 and k2k^2 at the resonant frequency of 294 MHz. The resulting FoM of 23.6 with a slow vpv_p of 1,800 m/s could enable miniature scale resonators for signal processing, sensing, and ultrasound transducer applications.

Acknowledgment

The authors would like to thank the funding support from the DARPA COFFEE program and Dr. Ben Griffith for the helpful discussion.

References

  1. [1]C. S. Lam, “A review of the recent development of mems and crystal oscillators and their impacts on the frequency control products industry,” in Proceedings - IEEE Ultrasonics Symposium, 2008.
  2. [2]G. Piazza, V. Felmetsger, P. Muralt, R. H. Olsson, and R. Ruby, “Piezoelectric aluminum nitride thin-films for microelectromechanical systems,” MRS Bulletin, vol. 37, no. 11, 2012. doi: 10.1557/mrs.2012.268.DOI
  3. [3]D. Royer and T. Valier-Brasier, Elastic Waves in Solids I: Propagation, vol. 1. 2022. doi: 10.1002/9781119092942.
  4. [4]B. A. Auld and R. E. Green, “Acoustic Fields and Waves in Solids: Two Volumes,” Phys Today, vol. 27, no. 10, 1974.DOI
  5. [5]G. Piazza, P. J. Stephanou, and A. P. Pisano, “Piezoelectric aluminum nitride vibrating contour-mode MEMS resonators,” Journal of Microelectromechanical Systems, vol. 15, no. 6, 2006.DOI
  6. [6]L. Colombo, A. Kochhar, G. Vidal-Álvarez, P. Simeoni, U. Soysal, and G. Piazza, “Sub-GHz X-Cut Lithium Niobate S0Mode MEMS Resonators,” Journal of Microelectromechanical Systems, vol. 31, no. 6, 2022.DOI
  7. [7]S. Gong and G. Piazza, “Design and analysis of lithium-niobate-based high electromechanical coupling RF-MEMS resonators for wideband filtering,” in IEEE Transactions on Microwave Theory and Techniques, 2013.DOI
  8. [8]M. Rinaldi, C. Zuniga, C. Zuo, and G. Piazza, “Super-high-frequency two-port AlN contour-mode resonators for RF applications,” in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, 2010.DOI
  9. [9]B. D. Zaitsev, S. G. Joshi, and I. E. Kuznetsova, “Investigation of quasi-shear-horizontal acoustic waves in thin plates of lithium niobate,” Smart Mater Struct, vol. 6, no. 6, 1997.DOI
  10. [10]S. Gong and G. Piazza, “Overmoded shear horizontal wave MEMS resonators using X-cut lithium niobate thin film,” in IEEE International Ultrasonics Symposium, IUS, 2014.DOI
  11. [11]Y. H. Song and S. Gong, “Elimination of Spurious Modes in SH0 Lithium Niobate Laterally Vibrating Resonators,” IEEE Electron Device Letters, vol. 36, no. 11, 2015.DOI
  12. [12]R. Lu, Y. Yang, M. H. Li, T. Manzaneque, and S. Gong, “GHz Broadband SH0 Mode Lithium Niobate Acoustic Delay Lines,” IEEE Trans Ultrason Ferroelectr Freq Control, vol. 67, no. 2, 2020.DOI
  13. [13]R. H. Olsson et al., “A high electromechanical coupling coefficient SH0 Lamb wave lithium niobate micromechanical resonator and a method for fabrication,” Sens Actuators A Phys, vol. 209, 2014.DOI
  14. [14]V. Plessky et al., “Laterally excited bulk wave resonators (XBArs) based on thin Lithium Niobate platelet for 5GHz and 13 GHz filters,” in IEEE MTT-S International Microwave Symposium Digest, 2019.
  15. [15]S. Yandrapalli, V. Plessky, J. Koskela, V. Yantchev, P. Turner, and L. G. Villanueva, “Analysis of XBAR resonance and higher order spurious modes,” in IEEE International Ultrasonics Symposium, IUS, 2019.DOI
  16. [16]J. Koulakis et al., “XBAR physics and next generation filter design,” in IEEE International Ultrasonics Symposium, IUS, 2021.DOI
  17. [17]Y. Yang, R. Lu, T. Manzaneque, and S. Gong, “Toward Ka Band Acoustics: Lithium Niobate Asymmetrical Mode Piezoelectric MEMS Resonators,” in IFCS 2018 - IEEE International Frequency Control Symposium, 2018.DOI
  18. [18]K. Nguyen et al., “Near-Spurious-Free Lithium Niobate Resonator for Piezoelectric Power Conversion with Q of 3500 and kt2of 45%,” in IEEE International Ultrasonics Symposium, IUS, 2022.DOI
  19. [19]S. Link, R. Lu, Y. Yang, A. E. Hassanien, and S. Gong, “An A1 Mode Resonator with 12 GHz using 160nm Lithium Niobate Suspended Thin Film,” in IEEE International Ultrasonics Symposium, IUS, 2021.DOI
  20. [20]R. Ruby, “Review and comparison of bulk acoustic wave FBAR, SMR technology,” in Proceedings - IEEE Ultrasonics Symposium, 2007.
  21. [21]W. Zhao et al., “15-GHz Epitaxial AlN FBARs on SiC Substrates,” IEEE Electron Device Letters, p. 1, 2023.DOI
  22. [22]Z. Schaffer, P. Simeoni, and G. Piazza, “33 GHz Overmoded Bulk Acoustic Resonator,” IEEE Microwave and Wireless Components Letters, vol. 32, no. 6, pp. 656–659, 2022.DOI
  23. [23]A. Gao, J. Zou, and S. Gong, “A 3.5 GHz AlN S1 lamb mode resonator,” in IEEE International Ultrasonics Symposium, IUS, 2017.DOI
  24. [24]J. Zou and A. P. Pisano, “Temperature compensation of the AlN Lamb wave resonators utilizing the S1 mode,” in 2015 IEEE International Ultrasonics Symposium, IUS 2015, 2015.DOI
  25. [25]K. Nguyen et al., “Spurious-Free Lithium Niobate Bulk Acoustic Resonator for Piezoelectric Power Conversion,” in IEEE International Frequency Control Symposium (IFCS), May 2023, 2023.DOI
  26. [26]K. Wang, U. Koelle, J. D. Larson, R. Thalhammer, and S. Martin, “FBAR laterally Coupled Resonator Filter,” in 2015 IEEE International Ultrasonics Symposium, IUS 2015, 2015.DOI
  27. [27]Z. Cao, R. Liu, J. Wu, P. L. Yu, and D. A. Feld, “Prediction of the H2 Response of an FBAR Resonator Using Finite Element Method,” in IEEE International Ultrasonics Symposium, IUS, 2018.DOI
  28. [28]L. Draudviliene, A. Meskuotiene, O. Tumsys, L. Mazeika, and V. Samaitis, “Metrological performance of hybrid measurement technique applied for the lamb waves phase velocity dispersion evaluation,” IEEE Access, vol. 8, 2020.DOI
  29. [29]Y. Lu and D. A. Horsley, “Modeling, Fabrication, and Characterization of Piezoelectric Micromachined Ultrasonic Transducer Arrays Based on Cavity SOI Wafers,” Journal of Microelectromechanical Systems, vol. 24, no. 4, 2015.DOI
  30. [30]A. E. Hassanien, R. Lu, and S. Gong, “Near-Zero Drift and High Electromechanical Coupling Acoustic Resonators at > 3.5 GHz,” IEEE Trans Microw Theory Tech, vol. 69, no. 8, 2021.DOI
  31. [31]R. Lu, Y. Yang, S. Link, and S. Gong, “Enabling Higher Order Lamb Wave Acoustic Devices with Complementarily Oriented Piezoelectric Thin Films,” Journal of Microelectromechanical Systems, vol. 29, no. 5, 2020.DOI
  32. [32]J. Kramer et al., “Thin-Film Lithium Niobate Acoustic Resonator with High Q of 237 and k2 of 5.1% at 50.74 GHz,” in IEEE International Frequency Control Symposium (IFCS), 2023.DOI
  33. [33]R. Lu and S. Gong, “A 15.8 GHz A6 Mode Resonator with Q of 720 in Complementarily Oriented Piezoelectric Lithium Niobate Thin Films,” in 2021 Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium, EFTF/IFCS 2021 - Proceedings, 2021.DOI
  34. [34]J. Kramer et al., “57 GHz Acoustic Resonator with k2 of 7.3 % and Q of 56 in Thin-Film Lithium Niobate,” in IEEE International Electron Devices Meeting (IEDM), 2022, pp. 16.4.1-16.4.4.DOI

Paper details

vlnc:W_5pbr68ez
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents