betaFeedback

WorksPhysics and Astronomy

A Variable-Spot-Size and Multi-Frequency Square-Pulsed Source (SPS) Approach for Comprehensive Characterization of Anisotropic Thermal Transport Properties in Multilayered Thin Films

Abstract

Multilayered thin-film structures are frequently encountered in industrial applications, where accurate thermal property characterization is essential for performance optimization. These films, typically ranging from nanometers to micrometers in thickness, often exhibit anisotropic thermal conductivity and non-bulk heat capacity, which are challenging to measure. In this study, we introduce a variable-spot-size and multi-frequency square-pulsed source (SPS) method for the simultaneous determination of anisotropic thermal conductivities, heat capacities, and interfacial thermal conductance in multilayered systems. By leveraging a broad modulation frequency range (1 Hz to 10 MHz) and tunable laser spot sizes, the SPS method enhances sensitivity to different thermal parameters across layers. We validate this approach on a silicon-on-insulator (SOI) sample comprising a 1.59 um Si layer, 1.03 um SiO2 layer, and a silicon substrate with a 122 nm aluminum (Al) transducer. The SPS method successfully extracts seven key thermal parameters, including the in-plane and cross-plane thermal conductivities and heat capacity of the Si film, the thermal conductivity and heat capacity of the SiO2 layer, the thermal conductivity of the substrate, and the interfacial thermal conductance between Al and Si. Temperature-dependent measurements from 80 to 500 K showed excellent agreement with literature values and first-principles predictions, confirming the method's accuracy and reliability. These results demonstrate the SPS method as a powerful tool for comprehensive thermal characterization of complex multilayered structures, with implications for both fundamental research and practical applications.

Introduction

Thin-film structures, particularly those in the nanometer to micrometer range, play a critical role in modern industrial applications, ranging from microelectronics [1, 2] and optoelectronics [3] to thermal management in advanced devices [4]. These films often exhibit complex thermal behavior, such as anisotropic thermal conductivity [5] and deviations in volumetric heat capacity from bulk values [6]. Accurate measurement of these thermal properties is essential for device performance and reliability. However, conventional techniques such as calorimetry and steady-state methods are often inadequate for thin films, especially in multilayered systems where heat transfer is strongly influenced by interfacial effects and anisotropy.

Among existing approaches, pump-probe techniques such as time-domain thermoreflectance (TDTR) [7, 8] and frequency-domain thermoreflectance (FDTR) [9] have become popular for characterizing thermal properties at the micro- and nanoscale. These methods use a modulated pump laser to heat the sample and a probe laser to monitor temperature-induced reflectance changes. While powerful, their limited frequency range and sensitivity trade-offs often prevent comprehensive extraction of thermal conductivities (both in-plane and cross-plane), heat capacities, and interfacial thermal transport properties in layered film systems within a single framework.

To overcome these challenges, we introduce the square-pulsed source (SPS) method—a versatile pump-probe technique capable of comprehensive thermal characterization [10, 11, 12]. By using a square-wave modulated pump beam and analyzing time-resolved reflectance signals over a broad frequency range (1 Hz to 10 MHz) and varied laser spot sizes, the SPS method enhances sensitivity to both in-plane and cross-plane transport across multiple layers.

In this work, we apply the SPS method to a silicon-on-insulator (SOI) sample to demonstrate its effectiveness. The method enables the simultaneous extraction of seven key thermal parameters, including the in-plane and cross-plane thermal conductivities and heat capacity of the Si film, thermal conductivity and heat capacity of the SiO₂ layer, thermal conductivity of the substrate, and interfacial thermal conductance between Al and Si. Results over 80-500 K show excellent agreement with literature and theoretical predictions, validating the SPS method as an accurate and versatile tool for multilayer thin-film thermal characterization.

Methodologies

Basic principle of the SPS technique

The SPS technique, illustrated schematically in Figure 1(a), employs a pump laser modulated with a 50% duty cycle square wave to generate periodic heating on the sample surface. A probe laser, focused on the same spot, detects the resulting temperature variations through the thermoreflectance effect. The reflected probe laser beam is captured by a photodetector, which converts the optical signals into corresponding electrical signals. These signals are processed by a periodic waveform analyzer, an integrated advanced function of the Zurich UHF lock-in amplifier, to produce time-resolved voltage signals over a complete square-wave heating cycle with a high signal-to-noise ratio. The resulting voltage signals, directly proportional to the sample’s temperature response, undergo normalization along both amplitude and time axes. Finally, a thermal model is applied to best fit the normalized data, enabling accurate determination of the specimen’s thermal properties [10, 13].

Image not extracted

Figure 1. (a) Schematic diagram of the experimental setup for the SPS method. (b) Schematic illustrating individual and combined thermal parameters in an NN-layered thin-film structure. The figure highlights how different parameters contribute to the system’s thermal response. These parameters form the basis for sensitivity analysis and signal fitting in SPS measurements.

In our system, the pump and probe lasers operate at 458 nm and 785 nm, respectively. To conduct the measurements, the sample is typically coated with a ∼\sim100 nm thick aluminum (Al) film as a transducer layer. With the Al film thickness being significantly greater than its optical skin depth (∼\sim6.2 nm at 458 nm), all incident optical energy is absorbed near the surface. Therefore, heat generation is confined within the Al film, and thermal transport into the underlying layers occurs solely through diffusion. This assumption underpins the surface heating boundary condition used in our thermal model fitting.

Principle of measuring multiple parameters in multilayered systems

The thermal response of an NN-layered system is influenced by several parameters, including the in-plane thermal conductivity (krk_r), cross-plane thermal conductivity (kzk_z), volumetric heat capacity (CC), and thickness (hh) of each layer, as well as the thermal conductance (GG) at each interface. Additional factors include the laser spot size (r0r_0) and the modulation frequency (f0f_0), resulting in a total of 5N5N parameters. Among these, f0f_0 is a set parameter, while all others are subject to uncertainties. These parameters are summarized in Figure 1(b).

The sensitivity of the normalized amplitude signal AnormA_{\mathrm{norm}} to any parameter ξ\xi is quantified using the sensitivity coefficient, defined as:

Sξ=∂ln⁡Anorm∂ln⁡ξ=ξAnorm∂Anorm∂ξ(1)S_{\xi}=\frac{\partial\ln A_{\mathrm{norm}}}{\partial\ln\xi}=\frac{\xi}{A_{\mathrm{norm}}}\frac{\partial A_{\mathrm{norm}}}{\partial\xi} \tag*{(1)}

This indicates that a 1% change in ξ\xi results in an SξS_{\xi}% change in the signal AnormA_{\mathrm{norm}}.

Chen and Jiang [14, 15] have demonstrated that the sensitivity coefficients for different parameters of the thermal system satisfy the following N+2N+2 relationships:

SCn=Shn+Skz,n−Skr,n,for n=1,2,…,N(2)S_{C_n}=S_{h_n}+S_{k_{z,n}}-S_{k_{r,n}},\qquad\text{for }n=1,2,\ldots,N \tag*{(2)}
∑n=1N−1(SGn+Shn)=−2∑n=1NSkz,n(3)\sum_{n=1}^{N-1}\left(S_{G_n}+S_{h_n}\right)=-2\sum_{n=1}^{N}S_{k_{z,n}} \tag*{(3)}
Sr0=−2∑n=1NSkr,n(4)S_{r_0}=-2\sum_{n=1}^{N}S_{k_{r,n}} \tag*{(4)}

Building on these relationships, Chen and Jiang [14, 15] propose that the thermal response is governed by specific key combined parameters. For the nnth layer, these parameters include kz,nCnhnCn\frac{\sqrt{k_{z,n}C_n}}{h_nC_n}, kz,nCnhn−1Cn−1\frac{\sqrt{k_{z,n}C_n}}{h_{n-1}C_{n-1}}, and kr,nCnr02\frac{k_{r,n}}{C_nr_0^2}. Additionally, for the interface beneath the nnth layer, the governing parameter is GnhnCn\frac{G_n}{h_nC_n}. These combined parameters, totaling 4N−34N-3, are summarized in Figure 1(b).

The sensitivity coefficients of AnormA_{\mathrm{norm}} to these combined parameters can be derived from the sensitivity coefficients of the individual parameters as follows:

Skz,1C1h1C1=2Skz1(5)S_{\frac{\sqrt{k_{z,1}C_1}}{h_1C_1}}=2S_{k_{z1}} \tag*{(5)}
Skz,nCnhnCn=2Skz,n+∑l=1n−1(2Skz,l+Shl+SGl);for n=2,…,N−1(6)S_{\frac{\sqrt{k_{z,n}C_n}}{h_nC_n}}=2S_{k_{z,n}}+\sum_{l=1}^{n-1}\left(2S_{k_{z,l}}+S_{h_l}+S_{G_l}\right);\qquad\text{for }n=2,\ldots,N-1 \tag*{(6)}
Skz,nCnhn−1Cn−1=−∑l=1n−1(2Skz,l+Shl+SGl);for n=2,…,N(7)S_{\frac{\sqrt{k_{z,n}C_n}}{h_{n-1}C_{n-1}}}=-\sum_{l=1}^{n-1}\left(2S_{k_{z,l}}+S_{h_l}+S_{G_l}\right);\qquad\text{for }n=2,\ldots,N \tag*{(7)}
SGnhncn=SGn′;for n=1,…,N−1(8)\frac{S_{G_n}}{h_n c_n}=S_{G_n}';\quad\text{for }n=1,\ldots,N-1 \tag*{(8)}
Skrncnr02=Skrn′;for n=1,…,N(9)\frac{S_{k_{rn}}}{c_n r_0^2}=S_{kr_n}';\quad\text{for }n=1,\ldots,N \tag*{(9)}

These combined parameters not only reveal the relationships among various parameters but also define the maximum number of parameters that can be extracted through fitting experimental signals. In some instances, certain combined parameters may exhibit partial coupling. To quantitatively evaluate the number of measurable parameters, singular value decomposition (SVD) can be performed on the sensitivity matrix: S=S=

[Sξ1⋯Sξj⋯Sξq]p×q,\begin{bmatrix} S_{\xi_1} & \cdots& S_{\xi_j} & \cdots& S_{\xi_q} \end{bmatrix}_{p \times q},

where pp is the number of data points and qq is the number of combined parameters being analyzed. Each column, Sξj=(Sξj,t1,…,Sξj,tp)TS_{\xi_j}=(S_{\xi_j,t_1},\ldots,S_{\xi_j,t_p})^{\mathrm{T}}, represents the sensitivity of the signal AnormA_{\mathrm{norm}} to the combined parameter ξj\xi_j at different time points. The number of measurable parameters is determined by the number of singular values of the sensitivity matrix SS that are larger than 0.1. These theories will be demonstrated through the measurement example of an SOI sample in § 3.

Results and discussion

Sample preparation and structure characterization

The sample in this study is a commercial SOI wafer fabricated using the Smart-CutTM process, with a nominal device layer thickness of 1.5 μm1.5\ \mu\mathrm{m} and an oxide layer thickness of 1 μm1\ \mu\mathrm{m}. For thermal measurements, a 100 nm Al transducer layer was deposited via electron beam evaporation. As shown in the cross-sectional SEM image in Figure 2(a), the actual measured thicknesses of the Al, Si, and SiO2\mathrm{SiO_2} layers are 122±6122 \pm6 nm, 1.59±0.05 μm1.59 \pm0.05\ \mu\mathrm{m}, and 1.03±0.03 μm1.03 \pm0.03\ \mu\mathrm{m}, respectively. The 122 nm Al thickness ensures complete absorption of the pump and probe beams within the Al layer, consistent with the surface heating assumption used in our thermal model (see § 2.1). The SEM image also reveals stratified sublayers within the SiO2\mathrm{SiO_2} layer. Further elemental analysis using Energy Dispersive X-ray Spectroscopy (EDX), shown in Figure 2(b), suggests that this stratification is likely structural or morphological rather than compositional.

Image not extracted

Figure 2. (a) Cross-sectional SEM image of the SOI sample, showing distinct layers of the Al transducer, Si device layer, and buried SiO2_2. (b) EDX mapping of the SiO2_2 layer, confirming uniform elemental distribution and indicating that the visible stratification arises from morphological, not compositional, variations. (c) Thermal model schematic used in SPS signal fitting, incorporating 19 intrinsic parameters and their grouping into 13 key combined parameters that govern heat diffusion. The diagram also defines the labeling system for these combined parameters, which are central to sensitivity and SVD analysis.

A multilayered thermal model based on the sample structure is developed, as shown in Figure 2(c). This model involves 19 intrinsic parameters, including krk_r, kzk_z, CC, and hh of the metal transducer layer (Al), device layer (Si film), and oxide layer (SiO2\mathrm{SiO_2}). It also accounts for krk_r, kzk_z, and CC of the bulk Si substrate. Three interfacial thermal conductances at the Al/Si film interface (G1G_1), the Si film/SiO2\mathrm{SiO_2} interface (G2G_2), and the SiO2\mathrm{SiO_2}/bulk Si interface (G3G_3) are involved, in addition to the laser spot radius (r0r_0). As discussed in § 2, these individual parameters combine to form 13 key parameters that primarily govern the heat diffusion process in the SOI sample, as shown in Figure 2(c). For clarity, these combined parameters are labeled with double-digit circled numbers, where the first digit represents the layer number and the second indicates the parameter’s sequence within that layer.

Measurement procedure

We employed a variable spot size and multi-frequency approach based on the SPS technique to probe multiple thermal parameters of the multilayered system. Specifically, high modulation frequencies (in the MHz range) were used to probe the thermal properties of the topmost layers, while low modulation frequencies (in the kHz range) probed the substrate. A large laser spot size reduced sensitivity to in-plane thermal transport, whereas a small spot size enhanced it. To illustrate the measurement process, we present an example of room-temperature measurements on this multilayered SOI system.

Qualitative analysis based on sensitivity curves

Figure 3Figure 1a-Figure 1f) shows the SPS signals measured at a spot size of 14.4 μm14.4\ \mu\mathrm{m} and a modulation frequency of 2 MHz2\ \mathrm{MHz}, along with the corresponding sensitivity coefficients. Figure 3Figure 1a and Figure 3Figure 1b display the heating and cooling phase signals, where the symbols represent experimental data and the curves represent best-fit results from the thermal model. Figure 3Figure 1c and Figure 3Figure 1d plot the sensitivity coefficients of the signals in Figure 3Figure 1a and Figure 3Figure 1b for all 19 individual parameters. For clarity, only parameters with sensitivity magnitudes greater than 0.05 are labeled.

Image not extracted

Figure 3. SPS signals and sensitivity analyses at MHz-range frequencies used to extract thermal properties of the Si device layer. (1a-1f) show results for a 2 MHz modulation frequency and a 14.4 μm\mu\mathrm{m} laser spot size, primarily probing G1G_1, kz2C2k_{z2}C_2, and C2C_2 of the Si layer. (2a-2f) show results at 1 MHz with a smaller 3.5 μm\mu\mathrm{m} spot size, enhancing sensitivity to kr2/C2k_{r2}/C_2. The associated sensitivity coefficients indicate which parameters most affect the signal, guiding which properties can be reliably extracted. The combined parameters include ⑪ kz1C1h1C1\frac{\sqrt{k_{z1}C_1}}{h_1C_1}, ⑬ G1h1C1\frac{G_1}{h_1C_1}, ㉑ kz2C2h2C2\frac{\sqrt{k_{z2}C_2}}{h_2C_2}, ㉒ kz2C2h1C1\frac{\sqrt{k_{z2}C_2}}{h_1C_1}, ㉓ kr2C2r02\frac{k_{r2}}{C_2r_0^2}, and ㉜ kz3C3h2C2\frac{\sqrt{k_{z3}C_3}}{h_2C_2}.

The sensitivity analysis indicates that this set of signals is most sensitive to the properties of the device layer, particularly the cross-plane thermal conductivity kz2k_{z2}, volumetric heat capacity C2C_2, and thickness h2h_2. Some parameters exhibit partial correlations, such as Sr0=−2Skr2S_{r_0}=-2S_{k_{r2}}, and SC2=Skz2−Skr2+Sh2S_{C_2}=S_{k_{z2}}-S_{k_{r2}}+S_{h_2}.

Figures 3(1e) and 3(1f) present the sensitivity coefficients to combined parameters, revealing that the signals are primarily sensitive to the following combined terms: ⑬ G1h1C1\frac{G_1}{h_1C_1}, ㉑ kz2C2h2C2\frac{\sqrt{k_{z2}C_2}}{h_2C_2}, and ㉒ kz2C2h1C1\frac{\sqrt{k_{z2}C_2}}{h_1C_1}. A closer examination shows that these combined parameters are not coupled, suggesting that they can be independently determined by fitting this set of signals. Once these combined parameters are extracted, we can determine G1G_1 from G1h1C1\frac{G_1}{h_1C_1}, kz2C2k_{z2}C_2 from kz2C2h1C1\frac{\sqrt{k_{z2}C_2}}{h_1C_1}, and C2C_2 from kz2C2h2C2\frac{\sqrt{k_{z2}C_2}}{h_2C_2}, provided that h1h_1, h2h_2 and C1C_1 are known.

To enhance sensitivity to the in-plane thermal conductivity kr2k_{r2} of the device layer, we repeated the measurements at a similar modulation frequency (1 MHz) but with a significantly smaller spot size of 3.5 μ\mum. The corresponding signals and sensitivity coefficients are shown in Figure 3(2a-2f). The sensitivity plots in Figures 3(2e) and 3(2f) confirm that this set of signals remains sensitive to ⑬ G1h1C1\frac{G_1}{h_1C_1}, ㉑ kz2C2h2C2\frac{\sqrt{k_{z2}C_2}}{h_2C_2} and ㉒ kz2C2h1C1\frac{\sqrt{k_{z2}C_2}}{h_1C_1}, but with a markedly increased sensitivity to ㉓ kr2C2r02\frac{k_{r2}}{C_2r_0^2} compared to the earlier measurement. Therefore, knowing r0r_0, h1h_1, h2h_2, and C1C_1, we can simultaneously fit both sets of signals to accurately determine G1G_1, kz2k_{z2}, C2C_2, and kr2k_{r2}.

To probe deeper layers, we employed a large laser spot size of 14.4 μ\mum and lowered the modulation frequency to 100 kHz and 10 kHz. The measured signals and corresponding sensitivity coefficients are shown in Figure 4. Lower modulation frequencies increase thermal penetration depth, making the signals more sensitive to underlying layers.

At 100 kHz, heat penetrates through the SiO2_2 layer, and the signals exhibit strong sensitivity to the following combined parameters: ㉑ kz2C2h2C2\frac{\sqrt{k_{z2}C_2}}{h_2C_2}, ㉒ kz2C2h1C1\frac{\sqrt{k_{z2}C_2}}{h_1C_1}, ㉓ kr2C2r02\frac{k_{r2}}{C_2r_0^2}, ㉛ kz3C3h3C3\frac{\sqrt{k_{z3}C_3}}{h_3C_3}, and ㉜ kz3C3h2C2\frac{\sqrt{k_{z3}C_3}}{h_2C_2}, as shown in Figures 4(1e) and 4(1f).

Since the device layer parameters have already been determined from the higher-frequency measurements, the sensitivity curves indicate that parameters ㉛ and ㉜ –associated with the oxide layer–are not coupled. Therefore, with the SiO2_2 layer thickness h3h_3 known, the cross-plane thermal conductivity kz3k_{z3} and volumetric heat capacity C3C_3 of the oxide layer can be extracted from these signals.

Further lowering the modulation frequency to 10 kHz increases sensitivity to the substrate properties. As shown in Figures 4(2e) and 4(2f), the signals (particularly in the cooling phase) show strong sensitivity to: ㊶ kz4C4h3C3\frac{\sqrt{k_{z4}C_4}}{h_3C_3} and ㊷ kr4C4r02\frac{k_{r4}}{C_4r_0^2}, parameters related to the substrate. However, Figures 4(2c) and 4(2d) show that the volumetric heat capacity C4C_4 of the substrate has very low sensitivity compared to other intrinsic parameters. This implies that treating C4C_4 as an unknown would introduce significant fitting uncertainty. Therefore, C4C_4 should be treated as a known input. With h3h_3 and C3C_3 known, kz4k_{z4} of the Si substrate can be determined by fitting this final set of signals.

Quantitative evaluation based on SVD analysis

We further assessed the measurability of the thermal parameters using SVD analysis. To apply this method, the sensitivities of the combined parameters under investigation were arranged into the matrix S\mathbf{S} as follows:

S=(S(1,ξ1)⋯S(1,ξ8)⋮⋱⋮S(4,ξ1)⋯S(4,ξ8))4p×8(10)\mathbf{S} = \begin{pmatrix} S_{(1,\xi_1)} & \cdots& S_{(1,\xi_8)} \\ \vdots& \ddots& \vdots\\ S_{(4,\xi_1)} & \cdots& S_{(4,\xi_8)} \end{pmatrix}_{4p \times8} \tag*{(10)}

Here, S(i,ξj)\mathbf{S}_{(i,\xi_j)} is a column vector of size p×1p \times1 (where pp is the number of data points in each signal set), containing the sensitivity coefficients of the iith set of signals to the jjth combined parameter. The eight combined parameters analyzed were: G1h1C1\frac{G_1}{h_1 C_1}, kz2C2h2C2\frac{\sqrt{k_{z2}C_2}}{h_2 C_2}, kz2C2h1C1\frac{\sqrt{k_{z2}C_2}}{h_1 C_1}, kr2C2r02\frac{k_{r2}}{C_2r_0^2}, kz3C3h3C3\frac{\sqrt{k_{z3}C_3}}{h_3 C_3}, kz3C3h2C2\frac{\sqrt{k_{z3}C_3}}{h_2 C_2}, kz4C4h3C3\frac{\sqrt{k_{z4}C_4}}{h_3 C_3}, and kr4C4r02\frac{k_{r4}}{C_4r_0^2}. The other five combined parameters, whose sensitivities remained below 0.05 across all four signal sets, were excluded from the analysis.

Upon decomposition, the diagonal matrix was obtained as:

Σ=diag⁡(55.94,28.58,18.46,7.41,4.93,1.49,1.05,0.63)\Sigma= \operatorname{diag}(55.94, 28.58, 18.46, 7.41, 4.93, 1.49, 1.05, 0.63)

Since all singular values exceeded 0.1, it confirms that these eight combined parameters are mathematically uncoupled. Therefore, in theory, eight thermal parameters—G1G_1, kz2k_{z2}, C2C_2, kr2k_{r2}, kz3k_{z3}, C3C_3, k4k_4, and C4C_4—can be independently determined by fitting the four sets of signals, assuming prior knowledge of h1h_1, C1C_1, h2h_2, h3h_3, and r0r_0, as well as the substrate isotropy condition k4=kr4=kz4k_4 = k_{r4} = k_{z4}.

However, when attempting to fit all eight parameters simultaneously, we observed unacceptably high uncertainty in C4C_4. This is attributed to the relatively weak sensitivity of C4C_4, as discussed in § 3.2.1. Therefore, in practice, we treat C4C_4 as a known input parameter.

This example demonstrates that SVD analysis is an effective tool for identifying the number of independently measurable parameters and assessing parameter coupling. However, while SVD establishes the mathematical independence of parameters, their practical measurability ultimately depends on the relative magnitude of their sensitivities.

Best fitting results

Building on the qualitative and quantitative analyses above, we conclude that seven thermal parameters of the SOI thermal system—G1G_1, kz2k_{z2}, C2C_2, kr2k_{r2}, kz3k_{z3}, C3C_3, and k4k_4—can be simultaneously determined by fitting the four sets of signals shown in Figure 3 and Figure 4. Meanwhile, six parameters of the system—h1h_1, C1C_1, h2h_2, h3h_3, C4C_4, and r0r_0—must be accurately known as input values. The remaining parameters (kr1k_{r1}, kz1k_{z1}, G2G_2, kr3k_{r3}, and G3G_3) are also treated as inputs, but their precise values have negligible impact on the fitting results.

Image not extracted

Figure 4. SPS signals and sensitivity analyses at lower kHz-range frequencies used to probe deeper layers, including the buried oxide layer and the Si substrate. (1a-1f) show results at 100 kHz, capturing the thermal response of the oxide layer. (2a-2f) show results at 10 kHz, increasing sensitivity to the Si substrate. The evolving sensitivity coefficients with decreasing modulation frequency illustrate how thermal penetration depth shifts with frequency, enabling selective probing of different layers. The combined parameters include ⑬ G1h1C1\frac{G_1}{h_1C_1}, ㉑ kz2C2h2C2\frac{\sqrt{k_{z2}C_2}}{h_2C_2}, ㉒ kz2C2h1C1\frac{\sqrt{k_{z2}C_2}}{h_1C_1}, ㉓ kr2C2r02\frac{k_{r2}}{C_2r_0^2}, ㉛ kz3C3h3C3\frac{\sqrt{k_{z3}C_3}}{h_3C_3}, ㉜ kz3C3h2C2\frac{\sqrt{k_{z3}C_3}}{h_2C_2}, ㊶ kz4C4h3C3\frac{\sqrt{k_{z4}C_4}}{h_3C_3}, and ㊷ kr4C4r02\frac{k_{r4}}{C_4r_0^2}.

Among the input parameters, the layer thicknesses were measured from high-resolution SEM cross-sectional images. The temperature-dependent heat capacities C1C_1 and C4C_4 were obtained from the TPRC database, with room-temperature values of 2.44 J/(cm3^3 · K) for Al and 1.66 J/(cm3^3 · K) for bulk Si. The laser spot sizes for each measurement set were determined using the spatial-domain thermoreflectance (SDTR) method [16], with an estimated uncertainty of 2%. The in-plane thermal conductivity of the Al film (kr1k_{r1}) at room temperature was calculated from its electrical resistivity (measured via the van der Pau method) using the Wiedemann–Franz law.

The temperature dependence of kr1k_{r1} was inferred from bulk single-crystal Al data [17], assuming a constant offset between bulk and thin-film electrical resistivities. Isotropic thermal conductivities were assumed for the Al film, SiO2_2 film, and Si substrate, with kr1=kz1k_{r1}=k_{z1}, kr3=kz3k_{r3}=k_{z3}, and kr4=kz4k_{r4}=k_{z4}. The interfacial thermal conductances of the Si/SiO2_2 and SiO2_2/Si interfaces were assumed as G2=G3=200±100G_2=G_3=200\pm100 MW/(m2⋅K\mathrm{m}^2\cdot\mathrm{K}); sensitivity analysis confirmed that variations in these values had negligible effect on the fitted results.

To extract the seven fitted parameters, we employed a hybrid optimization algorithm combining particle swarm optimization (PSO) with the quasi-Newton method to fit the four signal sets in Figure 3 and Figure 4. This hybrid approach achieved not only improved accuracy but also significantly higher computational efficiency than the commonly used MATLAB function “lsqnonlin”. Briefly, PSO—a global optimization scheme inspired by swarm intelligence—explores the parameter space to identify global optima. While highly robust and effective at avoiding local minima in high-dimensional spaces, PSO’s convergence rate declines after ∼10\sim10 iterations. To address this limitation, we transitioned to the quasi-Newton method, a gradient-based local optimizer, which rapidly refines the solution to high precision. By integrating the global exploration strength of PSO with the fast local convergence of quasi-Newton, we achieve efficient and accurate parameter estimation.

Layer/InterfaceParameterValue ±\pm UncertaintyUnitError (%)
Al/Si InterfaceG1G_1160±10.9160\pm10.9MW/(m2⋅K\mathrm{m}^2\cdot\mathrm{K})6.8
Si Filmkz2k_{z2} (cross-plane)100±4.7100\pm4.7W/(m⋅K\mathrm{m}\cdot\mathrm{K})4.6
kr2k_{r2} (in-plane)116±7.3116\pm7.3W/(m⋅K\mathrm{m}\cdot\mathrm{K})6.3
C2C_21.66±0.061.66\pm0.06J/(cm3⋅^3\cdot K)4.0
SiO2_2 Filmkz3k_{z3}1.38±0.071.38\pm0.07W/(m⋅K\mathrm{m}\cdot\mathrm{K})4.9
C3C_31.65±0.091.65\pm0.09J/(cm3⋅^3\cdot K)5.5
Si Substratek4k_4 (isotropic)148±6148\pm6W/(m⋅K\mathrm{m}\cdot\mathrm{K})4.0

Table 1. Room-temperature thermal properties of the SOI sample measured using the SPS method.

The best-fit results are as follows: the Al/Si interfacial thermal conductance is G1=160±10.9G_1=160\pm10.9 MW/(m2⋅K\mathrm{m}^2\cdot\mathrm{K}); the cross-plane and in-plane thermal conductivity of the Si film are kz2=100±4.7k_{z2}=100\pm4.7 W/(m⋅K\mathrm{m}\cdot\mathrm{K}) and kr2=116±7.3k_{r2}=116\pm7.3 W/(m⋅K\mathrm{m}\cdot\mathrm{K}), respectively; the volumetric heat capacity of the Si layer is C2=1.66±0.06C_2=1.66\pm0.06 J/(cm3⋅^3\cdot K); the thermal conductivity and volumetric heat capacity of the SiO2_2 layer are kz3=1.38±0.07k_{z3}=1.38\pm0.07 W/(m⋅K\mathrm{m}\cdot\mathrm{K}) and C3=1.65±0.09C_3=1.65\pm0.09 J/(cm3⋅^3\cdot K); and the thermal conductivity of the Si substrate is kz4=148±6k_{z4}=148 \pm6 W/(m ⋅\cdot K). Uncertainties were estimated using a full error propagation method that accounts for both the uncertainties of input parameters and signal noise. This uncertainty analysis approach, originally developed by Yang et al. [18], has been widely adopted in studies employing TDTR, FDTR, and other thermoreflectance techniques [10, 11, 16, 19, 20, 21, 22].

Temperature-dependent results and discussion

The measurements were repeated across temperatures from 80 to 500 K, with results summarized in Figure 5 as a function of temperature. Solid symbols represent the current measurements, solid curves denote recommended values from the TPRC database (for kSi,bulkk_{\mathrm{Si,bulk}}, kSiO2k_{\mathrm{SiO_2}}, CSiC_{\mathrm{Si}}, and CSiO2C_{\mathrm{SiO_2}}), and dashed curves correspond to theoretical predictions (for kr,Si filmk_{r,\mathrm{Si\ film}}, kz,Si filmk_{z,\mathrm{Si\ film}}, and GAl/SiG_{\mathrm{Al/Si}}). The observed temperature dependence of the thermal parameters offers important insight into the underlying phonon transport mechanisms and the structural characteristics of the multilayered SOI system.

Image not extracted

Figure 5. Temperature dependence of the seven thermal parameters extracted from the SOI sample using the SPS method: (a) In-plane and cross-plane thermal conductivities of the Si film (kr,Si filmk_{r,\mathrm{Si\,film}} and kz,Si filmk_{z,\mathrm{Si\,film}}), isotropic thermal conductivities of the SiO2 layer (kSiO2k_{\mathrm{SiO_2}}) and the Si substrate (kSi,bulkk_{\mathrm{Si,bulk}}); (b) Volumetric heat capacities of the Si (CSiC_{\mathrm{Si}}) and SiO2 (CSiO2C_{\mathrm{SiO_2}}) layers; and (c) Interfacial thermal conductance at the Al/Si interface (GAl/SiG_{\mathrm{Al/Si}}). Solid symbols represent the SPS measurements at different temperatures, with vertical error bars indicating uncertainty based on full error propagation. Solid lines denote recommended values from the TPRC database [23, 24], and dashed lines represent first-principles or model-based predictions [27].

For parameters with well-established literature values (kSi,bulkk_{\mathrm{Si,bulk}}, kSiO2k_{\mathrm{SiO_2}}, CSiC_{\mathrm{Si}}, and CSiO2C_{\mathrm{SiO_2}}), our measurements show excellent agreement with TPRC recommendations [23, 24]. Notably, as the temperature decreases toward 100 K, the measured kSi,bulkk_{\mathrm{Si,bulk}} increases to 890 W/(m ⋅\cdot K), aligning with accepted literature despite an uncertainty of up to 60%. This large uncertainty primarily stems from the reduced signal-to-noise ratio (SNR) under cryogenic conditions, where the substrate exhibits significantly higher thermal conductivity.

To ensure sufficient sensitivity to kSi,bulkk_{\mathrm{Si,bulk}} at low temperatures, we employ a large laser spot size (r0>30r_0 > 30 μ\mum) and a low modulation frequency (f0<20f_0 < 20 kHz). However, this combination reduces the magnitude of the surface temperature rise, necessitating higher pump laser power to maintain an adequate SNR. Our current system is limited to a maximum pump power of 150 mW, which is sufficient for most measurements but constrains the achievable SNR under these specific conditions.

As with other thermoreflectance techniques, the SPS method requires that the steady-state surface temperature rise induced by laser heating remains below 10 K or 10% of the sample’s absolute temperature, whichever is smaller [7], to ensure linearity and avoid sample damage. The steady-state surface temperature rise for a multilayered system can be estimated using [25]:

ΔT=Pπr02∑i=1N−1(hikz,i+1Gi)+P2πr02kr,Nkz,N(11)\Delta T = \frac{P}{\pi r_0^2}\sum_{i=1}^{N-1}\left(\frac{h_i}{k_{z,i}}+\frac{1}{G_i}\right)+\frac{P}{2\sqrt{\pi r_0^2 k_{r,N}k_{z,N}}} \tag*{(11)}

where P=α1P1+α2P2P = \alpha_1 P_1 + \alpha_2 P_2 is the total absorbed laser power from the pump and probe beams, with absorptivities α1\alpha_1, α2\alpha_2, and powers P1P_1, P2P_2. This equation shows that inadequate absorbed power may lead to a sub-optimal temperature rise, while excessive laser power risks non-linear effects or damage.

The absorptivity of the transducer is a key factor in this balance. In our case, the Al transducer absorbs only ~10% of the incident light at 458 nm. Replacing it with a higher-absorptivity material such as titanium nitride (TiN), which absorbs up to ~80% at similar wavelengths [26], could enhance thermal excitation efficiency without increasing laser power. This improvement would help reduce uncertainty in low-temperature measurements and expand the SPS method’s applicability to high-conductivity or thermally constrained samples.

In contrast, measurements of the Si and SiO2_2 films are less affected by these constraints at low temperatures, as a smaller spot size (r0≈5 μmr_0 \approx5\,\mu\mathrm{m}) remains sufficient for sensitivity. The thermal conductivity of the SiO2_2 layer kSiO2k_{\mathrm{SiO_2}} remains low across all temperatures due to its amorphous structure, which limits phonon mean free paths.

Both the measured CSiC_{\mathrm{Si}} and CSiO2C_{\mathrm{SiO_2}} values closely follow TPRC recommendations [23] and increase with temperature, as expected from the Debye model, which predicts a cubic temperature dependence at low temperatures and saturation at high temperatures. Notably, CSiC_{\mathrm{Si}} and CSiO2C_{\mathrm{SiO_2}} are comparable across the measured temperature range. Between 100 K and 300 K, CSiC_{\mathrm{Si}} is slightly higher than CSiO2C_{\mathrm{SiO_2}}, whereas above 300 K, this trend reverses, with CSiC_{\mathrm{Si}} becoming slightly lower—a subtle behavior that is consistent with TPRC reference data. The heat capacity of the Si film closely follows the bulk trend, indicating minimal deviation from bulk phonon density of states despite its sub-micrometer thickness.

For the other three parameters (kr,Si filmk_{r,\mathrm{Si\ film}}, kz,Si filmk_{z,\mathrm{Si\ film}}, and GAl/SiG_{\mathrm{Al/Si}}) lacking widely established literature values, our measurements also align well with theoretical predictions. Here, predictions of kr,Si filmk_{r,\mathrm{Si\ film}} and kz,Si filmk_{z,\mathrm{Si\ film}} for the 1.6 μ\mum-thick Si film were computed using the first-principles method (see Appendix § 5.1 for calculation details), and GAl/SiG_{\mathrm{Al/Si}} was obtained from reference [27], where it was calculated based on the diffuse mismatch model (DMM). Both kr,Si filmk_{r,\mathrm{Si\ film}} and kz,Si filmk_{z,\mathrm{Si\ film}} are lower than the bulk thermal conductivity and increase as temperature decreases. Their difference is small above room temperature but becomes more pronounced at lower temperatures, all matching theoretical expectations.

It is important to note that as the temperature decreases to 100 K, the uncertainty in kz,Si filmk_{z,\mathrm{Si\,film}} from our measurements increases substantially, reaching 36%. This large uncertainty primarily results from the reduced sensitivity of the measurement to kz,Si filmk_{z,\mathrm{Si\,film}}, which is dictated by the sample’s thermal structure. At 100 K, the combination of reduced kSiO2k_{\mathrm{SiO_2}} and increased kz,Si filmk_{z,\mathrm{Si\,film}} causes the cross-plane thermal resistance of the system to be dominated by the oxide layer. The thermal resistance of the Si film becomes negligible, rendering the surface temperature response insensitive to kz,Si filmk_{z,\mathrm{Si\,film}}, leading to significant uncertainty in its determination. In contrast, the measurement of kr,Si filmk_{r,\mathrm{Si\,film}} remained unaffected, as the increased thermal resistance of the oxide layer enhances lateral heat spreading within the Si film, thereby maintaining high sensitivity to kr,Si filmk_{r,\mathrm{Si\,film}}.

The measured GAl/SiG_{\mathrm{Al/Si}} increases with temperature, aligning qualitatively with the DMM, though with consistently lower values. This discrepancy arises from the DMM’s idealized assumption of an atomically sharp, oxide-free interface—an assumption that does not hold for our sample. Specifically, a 2–3 nm native SiO2\mathrm{SiO}_{2} layer exists at the Al/Si interface due to the absence of hydrofluoric acid (HF) cleaning before Al deposition on the SOI substrate. This interfacial oxide introduces additional phonon scattering mechanisms and thermal resistance not accounted for by the DMM, thereby limiting the model’s quantitative accuracy in describing real-world systems.

In the literature, similar SOI structures were previously studied by Jiang et al. [28, 29] using TDTR to extract kr,Si filmk_{r,\mathrm{Si\ film}} and kz,Si filmk_{z,\mathrm{Si\ film}} of Si films with thicknesses ranging from 1–10 μ\mum. Their approach employed a dual-frequency TDTR approach [30] with modulation frequencies of 10 MHz and 3 MHz to minimize sensitivity to the Al transducer layer, thereby improving the accuracy of kz,Si filmk_{z,\mathrm{Si\ film}}, with a reported uncertainty of approximately 10%. To measure kr,Si filmk_{r,\mathrm{Si\ film}}, a low modulation frequency of 0.5 MHz was used, with kz,Si filmk_{z,\mathrm{Si\ film}} treated as a fixed input parameter. In contrast to our current study, which simultaneously determines seven thermal properties of the SOI sample, the TDTR measurements were limited to extracting only three: kr,Si filmk_{r,\mathrm{Si\ film}}, kz,Si filmk_{z,\mathrm{Si\ film}}, and GAl/SiG_{\mathrm{Al/Si}}.

Figure 6 compares our measurements of kr,Si filmk_{r,\mathrm{Si\ film}} and kz,Si filmk_{z,\mathrm{Si\ film}} for the 1.6 μ\mum-thick Si film with those reported by Jiang et al. [28, 29], alongside first-principles predictions at 300 K and 100 K. At both temperatures, our results show good agreement with both the TDTR data and theoretical values. Importantly, our measurements exhibit reduced uncertainties relative to TDTR, primarily because our method simultaneously determines a larger set of thermal parameters. As a result, uncertainties in intermediate parameters do not propagate into the final values of kr,Si filmk_{r,\mathrm{Si\ film}} and kz,Si filmk_{z,\mathrm{Si\ film}}. Furthermore, while TDTR could only characterize relatively thick Si films (>4> 4 μ\mum) at 100 K, our method remains effective for thinner films, such as the 1.6 μ\mum-thick sample, due to the enhanced sensitivity provided by the variable-spot-size, multi-frequency SPS approach across a broad range of modulation frequencies and laser spot sizes. This comparison underscores several advantages of the SPS method over TDTR, including its ability to extract a larger set of thermal parameters simultaneously, reduced uncertainty in measured values, and superior applicability to thinner films and low-temperature conditions where TDTR becomes less effective. Overall, the excellent agreement between our measurements, prior experimental data, and first-principles predictions confirms the accuracy and robustness of the current method.

Image not extracted

Figure 6. Comparison of the in-plane and cross-plane thermal conductivities of the 1.6 μm-thick Si film obtained using the SPS method with literature data and theoretical predictions at two temperatures: (a) 300 K and (b) 100 K. Solid symbols represent the SPS measurements from this work; open symbols correspond to TDTR results reported by Jiang et al. [28, 29]. Curves represent first-principles predictions. The SPS results show strong agreement with both experimental and theoretical references, with reduced uncertainty achieved through simultaneous multi-parameter fitting.

Conclusions

In summary, we have developed and validated a variable-spot-size, multi-frequency square-pulsed source (SPS) method for comprehensive thermal characterization of multilayered thin-film systems. This approach enables the simultaneous extraction of in-plane and cross-plane thermal conductivities, volumetric heat capacities, and interfacial thermal conductance within a single experimental framework. By combining a wide modulation frequency range with tunable laser spot sizes, the method achieves enhanced sensitivity across multiple layers and directions of heat transport.

Applied to a silicon-on-insulator (SOI) sample, the SPS method successfully determined seven key thermal parameters with high accuracy. These results exhibit strong consistency with literature data and theoretical predictions over a broad temperature range (80–500 K), confirming its reliability and broad applicability for analyzing multilayered thermal transport. These findings highlight the strength of the SPS technique in resolving anisotropic and interface-dominated heat transport in complex multilayer systems.

Although this study focused on an SOI sample, the SPS technique is broadly applicable to other multilayered systems, particularly those with anisotropy, buried interfaces, or non-bulk thermal properties. Its tunable measurement configuration offers flexibility across a range of material geometries and thermal regimes.

However, challenges may arise when dealing with strong lateral heterogeneity, non-planar geometries, or temperature-dependent optical properties, where accurate thermal modeling becomes more complex. Addressing these limitations will be an important direction for future refinement and application of the SPS method.

Appendix

First-principles calculation of krk_r and kzk_z of Si films

The lattice thermal conductivity tensor can be calculated from the phonon Boltzmann transport equation (BTE) as:

κ=1ΩN∑qpℏωqpvqpFqp(∂nqp0∂T)(12)\kappa= \frac{1}{\Omega N}\sum_{q\mathbf{p}} \hbar\omega_{q\mathbf{p}}\mathbf{v}_{q\mathbf{p}}\mathbf{F}_{q\mathbf{p}}\left(\frac{\partial n^0_{q\mathbf{p}}}{\partial T}\right) \tag*{(12)}

where qpq\mathbf{p} denotes a phonon mode labeled by wave vector q\mathbf{q} and polarization p\mathbf{p}, Ω\Omega is the unit cell volume, and NN is the number of sampled points in the first Brillouin zone. ωqp\omega_{q\mathbf{p}} and vqp\mathbf{v}_{q\mathbf{p}} are the phonon frequency and group velocity, respectively. nqp0n^0_{q\mathbf{p}} is the Bose-Einstein distribution function, and Fqp\mathbf{F}_{q\mathbf{p}} is the phonon mean free displacement [31], given by

Fqp=τqp0(vqp+Δqp)(13)\mathbf{F}_{q\mathbf{p}}=\tau^0_{q\mathbf{p}}\left(\mathbf{v}_{q\mathbf{p}}+\mathbf{\Delta}_{q\mathbf{p}}\right) \tag*{(13)}

Here, τqp0\tau^0_{q\mathbf{p}} is the relaxation time accounting for both three-phonon and isotope scattering, and Δqp\mathbf{\Delta}_{q\mathbf{p}} is the correction term used in the iterative solution of the BTE. The second- and third-order interatomic force constants (IFCs) for Si are adopted from the FourPhonon package [31], and a 40×40×4040 \times40 \times40 q-point mesh is employed. This setup yields a calculated bulk thermal conductivity of 148 W/(m · K) at room temperature.

For thin films, the relaxation time is further modified by a suppression function SqpS_{q\mathbf{p}} to account for additional boundary scattering:

τqpfilm=Sqpτqp0(14)\tau^{\mathrm{film}}_{q\mathbf{p}}=S_{q\mathbf{p}}\tau^0_{q\mathbf{p}} \tag*{(14)}

For in-plane (parallel) thermal transport, the suppression function is given by [32]:

Sqp∥=1−(1−σ)Knqp[1−exp⁡(−1Knqp)]1−σexp⁡(−1Knqp)(15)S^{\parallel}_{q\mathbf{p}}=1-\frac{(1-\sigma)\mathrm{Kn}_{q\mathbf{p}}\left[1-\exp\left(-\frac{1}{\mathrm{Kn}_{q\mathbf{p}}}\right)\right]}{1-\sigma\exp\left(-\frac{1}{\mathrm{Kn}_{q\mathbf{p}}}\right)} \tag*{(15)}

Here, σ\sigma is the specularity parameter, set to zero to model fully diffuse boundary scattering. The Knudsen number Knqp\mathrm{Kn}_{qp} is defined as:

Knqp=∣Λqpz∣L(16)\mathrm{Kn}_{qp} = \frac{\left|\Lambda_{qp}^{z}\right|}{L} \tag*{(16)}

where Λqpz\Lambda_{qp}^{z} is the phonon mean free path projected onto the cross-plane (z) direction, and LL is the film thickness.

For cross-plane (perpendicular) transport, the suppression function is [32]:

Sqp⊥=11+2Knqp(17)S_{qp}^{\perp} = \frac{1}{1 + 2\mathrm{Kn}_{qp}} \tag*{(17)}

In the resulting thermal conductivity tensor, the κzz\kappa^{zz} component corresponds to the cross-plane thermal conductivity κz\kappa_z, while κxx=κyy\kappa^{xx} = \kappa^{yy} represents the in-plane thermal conductivity κr\kappa_r of the film.

Acknowledgments

The authors wish to thank Dr. Jun Su from the Center of Optoelectronic Micro & Nano Fabrication and Characterization Facility at the Wuhan National Laboratory for Optoelectronics, Huazhong University of Science and Technology, for his assistance with the SEM and EDX testing. This work is supported by the National Natural Science Foundation of China (NSFC) through Grant No. 52376058.

Data availability

The data that support the findings of this study are available from the corresponding author upon reasonable request.

References

References

  1. [1]T. Wu, X. Ren, D. Cornil, C. Quarti, I.E. Jacobs, L. Zhang, N. Fukui, D. Beljonne, H. Nishihara, H. Sirringhaus, Revealing the charge transport physics in metallic coordination nanosheets by thermoelectric and magnetotransport measurements, Science Advances, 11 (2025) eadt9196.DOI
  2. [2]S.P. Murarka, Silicide thin films and their applications in microelectronics, Intermetallics, 3 (1995) 173-186.DOI
  3. [3]J. Chen, Y. Zhou, Y. Fu, J. Pan, O.F. Mohammed, O.M. Bakr, Oriented Halide Perovskite Nanostructures and Thin Films for Optoelectronics, Chem. Rev., 121 (2021) 12112-12180.DOI
  4. [4]H. Song, J. Liu, B. Liu, J. Wu, H.-M. Cheng, F. Kang, Two-Dimensional Materials for Thermal Management Applications, Joule, 2 (2018) 442-463.DOI
  5. [5]H. Zhang, S. Hu, M. Tian, X. Gu, Current density and thickness dependent anisotropic thermal conductivity of electroplated copper thin films, Mater. Sci. Semicond. Process., 187 (2025).DOI
  6. [6]D.-W. Oh, C. Ko, S. Ramanathan, D.G. Cahill, Thermal conductivity and dynamic heat capacity across the metal-insulator transition in thin film VO2, Appl. Phys. Lett., 96 (2010) 151906.
  7. [7]P. Jiang, X. Qian, R. Yang, Tutorial: Time-domain thermoreflectance (TDTR) for thermal property characterization of bulk and thin film materials, J. Appl. Phys., 124 (2018) 161103.DOI
  8. [8]A.J. Schmidt, PUMP-PROBE THERMOREFLECTANCE, Annu. Rev. Heat Transfer, 16 (2014) 159.
  9. [9]J. Yang, C. Maragliano, A.J. Schmidt, Thermal property microscopy with frequency domain thermoreflectance, Rev. Sci. Instrum., 84 (2013) 104904.DOI
  10. [10]T. Chen, S. Song, Y. Shen, K. Zhang, P. Jiang, Simultaneous measurement of thermal conductivity and heat capacity across diverse materials using the square-pulsed source (SPS) technique, International Communications in Heat and Mass Transfer, 158 (2024) 107849.DOI
  11. [11]T. Chen, P. Jiang, An optical method for measuring local convective heat transfer coefficients over 100 W/(m2·K) with sub-millimeter resolution, Measurement, 249 (2025) 117001.DOI
  12. [12]T. Chen, S. Song, R. Hu, P. Jiang, Comprehensive measurement of three-dimensional thermal conductivity tensor using a beam-offset square-pulsed source (BO-SPS) approach, International Journal of Thermal Sciences, 207 (2025) 109347.DOI
  13. [13]S. Song, T. Chen, P. Jiang, Comprehensive thermal property measurement of semiconductor heterostructures using the square-pulsed source (SPS) method, J. Appl. Phys., 137 (2025) 055101.DOI
  14. [14]T. Chen, P. Jiang, Decoupling thermal properties in multilayered systems for advanced thermoreflectance experiments, Physical Review Applied, 23 (2025) 044004.DOI
  15. [15]T. Chen, P.-Q. Jiang, Unraveling intrinsic relationship of thermal properties in thermoreflectance experiments, Acta Physica Sinica, 73 (2024) 230202.DOI
  16. [16]P. Jiang, D. Wang, Z. Xiang, R. Yang, H. Ban, A new spatial-domain thermoreflectance method to measure a broad range of anisotropic in-plane thermal conductivity, Int. J. Heat Mass Transfer, 191 (2022) 122849.DOI
  17. [17]Y. Touloukian, R. Powell, C. Ho, P. Klemens, Thermophysical Properties of Matter-The TPRC Data Series. Volume 1. Thermal Conductivity-Metallic Elements and Alloys, DTIC Document, 1970.
  18. [18]J. Yang, E. Ziade, A.J. Schmidt, Uncertainty analysis of thermoreflectance measurements, Rev. Sci. Instrum., 87 (2016) 014901.DOI
  19. [19]P. Jiang, X. Qian, X. Li, R. Yang, Three-dimensional anisotropic thermal conductivity tensor of single crystalline β-Ga2O3, Appl. Phys. Lett., 113 (2018) 232105.DOI
  20. [20]P. Jiang, X. Qian, R. Yang, A new elliptical-beam method based on time-domain thermoreflectance (TDTR) to measure the in-plane anisotropic thermal conductivity and its comparison with the beam-offset method, Rev. Sci. Instrum., 89 (2018) 094902.DOI
  21. [21]P. Jiang, X. Qian, R. Yang, L. Lindsay, Anisotropic thermal transport in bulk hexagonal boron nitride, Physical Review Materials, 2 (2018) 064005.DOI
  22. [22]Y. Pang, Y. Li, Z. Gao, X. Qian, X. Wang, J. Hong, P. Jiang, Thermal transport manipulated by vortex domain walls in bulk h-ErMnO3, Materials Today Physics, 31 (2023) 100972.
  23. [23]Y. Touloukian, E. Buyco, Thermophysical Properties of Matter-the TPRC Data Series. Volume 5. Specific Heat-Nonmetallic Solids, DTIC Document, 1970.
  24. [24]Y. Touloukian, R. Powell, C. Ho, P. Klemens, Thermophysical Properties of Matter-the TPRC Data Series. Volume 2. Thermal Conductivity Nonmetallic Solids, IFI/Plenum, New York, Washington, 1970.
  25. [25]P. Jiang, H. Ban, Transient and steady-state temperature rise in three-dimensional anisotropic layered structures in pump-probe thermoreflectance experiments, J. Phys. D: Appl. Phys., 54 (2020) 035304.arxiv.org/abs/1912.01534
  26. [26]C.M. Rost, J. Braun, K. Ferri, L. Backman, A. Giri, E.J. Opila, J.-P. Maria, P.E. Hopkins, Hafnium nitride films for thermoreflectance transducers at high temperatures: Potential based on heating from laser absorption, Appl. Phys. Lett., 111 (2017) 151902.DOI
  27. [27]Q. Li, F. Liu, S. Hu, H. Song, S. Yang, H. Jiang, T. Wang, Y.K. Koh, C. Zhao, F. Kang, J. Wu, X. Gu, B. Sun, X. Wang, Inelastic phonon transport across atomically sharp metal/semiconductor interfaces, Nat. Commun., 13 (2022) 4901.DOI
  28. [28]P. Jiang, L. Lindsay, Y.K. Koh, Role of low-energy phonons with mean-free-paths >0.8 μm in heat conduction in silicon, J. Appl. Phys., 119 (2016) 245705.DOI
  29. [29]P. Jiang, L. Lindsay, X. Huang, Y.K. Koh, Interfacial phonon scattering and transmission loss in >1 μm thick silicon-on-insulator thin films, Phys. Rev. B, 97 (2018) 195308.DOI
  30. [30]P. Jiang, B. Huang, Y.K. Koh, Accurate measurements of cross-plane thermal conductivity of thin films by dual-frequency time-domain thermoreflectance (TDTR), Rev. Sci. Instrum., 87 (2016) 075101.DOI
  31. [31]Z. Han, X. Yang, W. Li, T. Feng, X. Ruan, FourPhonon: An extension module to ShengBTE for computing four-phonon scattering rates and thermal conductivity, Comput. Phys. Commun., 270 (2022) 108179.DOI
  32. [32]J. Carrete, B. Vermeersch, A. Katre, A. van Roekegh em, T. Wang, G.K.H. Madsen, N. Mingo, almaBTE : A solver of the space–time dependent Boltzmann transport equation for phonons in structured materials, Comput. Phys. Commun., 220 (2017) 351-362.DOI

Paper details

vlnc:W_5pncvj34
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents