betaFeedback

WorksPhysics and Astronomy

Preparation of large Cu3Sn single crystal by Czochralski method

Abstract

Cu3Sn was recently predicted to host topological Dirac fermions, but related research is still in its infancy. The growth of large and high-quality Cu3Sn single crystals is, therefore, highly desired to investigate the possible topological properties. In this work, we report the single crystal growth of Cu3Sn by Czochralski (CZ) method. Crystal structure, chemical composition, and transport properties of Cu3Sn single crystals were analyzed to verify the crystal quality. Notably, compared to the mm-sized crystals from a molten Sn-flux, the cm-sized crystals obtained by the CZ method are free from contamination from flux materials, paving the way for the follow-up works.

Introduction

Over the past decade, topological materials have attracted significant attention, because their ultrahigh mobility and magnetoresistance may lead to the next generation of device applications [1, 2]. In topological insulators, the current flow only along their surface while bulk exhibits semiconducting or insulating behavior with a band gap. In this context, topological semimetals are more suitable for the high mobility device application due to their bulk Dirac point originating from the crossing of conduction and valence bands. Thus, searching the applicable topological semimetal is currently one of the most interesting issues. Furthermore, a more important point in terms of finding such materials is that it is typically composed of inexpensive and nontoxic elements and can be grown to large-sized single crystals.

In this point of view, Cu-Sn alloys, so-called bronze, can be a promising candidate. Cu-Sn alloy has been used for the longest time in human history, and the discovery of this alloy allowed humankind opened the Bronze Age. Cu-Sn alloys have been studied a lot, especially for high-temperature applications, owing to their excellent thermodynamic and kinetic stability [3].

On the other hand, their topological properties do not attract lots of interest due to lack of understanding, however they become major subjects of great interest recently [4]. Among the Cu-Sn alloys, a Cu3Sn\mathrm{Cu}_3\mathrm{Sn} phase can crystallize as three different structures including the orthorhombic [5, 6], hexagonal [7], and cubic structures [8], which makes this system particularly interesting. Based on the recent research, all the Cu3Sn\mathrm{Cu}_3\mathrm{Sn} phases can be categorized into topological semimetals [9]. More recently, C. Liu et al. reported the observation of clear de Haas-van Alphen oscillations in orthorhombic Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystals grown by the self-flux method suggesting it exhibits a nontrivial band topology. Interestingly, the mobility of huge hole carrier (nh∼2.68×1022 cm−3n_h \sim2.68 \times10^{22}\ \mathrm{cm}^{-3}) in the Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystal is estimated to be μ∼490 cm2V−1s−1\mu\sim490\ \mathrm{cm}^2\mathrm{V}^{-1}\mathrm{s}^{-1}, which is an order of magnitude higher than that of electron carriers in the topologically trivial Cu single crystal μ∼35 cm2V−1s−1\mu\sim35\ \mathrm{cm}^2\mathrm{V}^{-1}\mathrm{s}^{-1} [10]. This study additionally suggested the possibility of a bronze-based topological semimetal with highly mobile carriers.

Herein, we report the growth of a large-sized intermetallic Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystal by the Czochralski (CZ) method. The CZ method is one of the powerful tools for the growth of the large-scale ultrapure single crystal and has contributed to the growth of a lot of materials, such as metal oxides [11], heavy fermion systems [12], and chiral compounds [13]. Compared to the crystals grown by the flux method, whose notable downside is that the flux can be trapped inside the crystal or remain on the edges or surface, the crystals grown by CZ method are free of contamination. The contamination from the flux can deteriorate the physical properties of the crystal, hindering the understanding of intrinsic behavior. The Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystal grown by the CZ method is around several centimeters, which is much larger than the self-flux grown crystals [5]. Based on the X-ray diffraction (XRD) and scanning electron microscopy with energydispersive spectroscopy (EDS), the crystal structure of the obtained single crystal was confirmed to be orthorhombic Cu3Sn\mathrm{Cu}_3\mathrm{Sn} with space group Pmmn\mathit{Pmmn}.

Experiments

Intermetallic single crystals of Cu3Sn\mathrm{Cu}_3\mathrm{Sn} were grown by the Czochralski method using a single crystal growth system installed in Quantum Matter Core-Facility of Pusan National University. Cu-Sn compounds were weighed according to the stoichiometric ratio of Cu: Sn and 3: 1.1 at %. The excess Sn is used to compensate for the volatilization of Sn during the single crystal growth at high temperatures. The raw materials for growing Cu3Sn\mathrm{Cu}_3\mathrm{Sn} were heated in a 40 kHz RF induced coil system. A graphite crucible whose diameter and height are 45 mm and 50 mm was used for the crystal growth. Growths were carried out several times by re-melting synthesized materials and introducing seeds. Seeds were cut first from polycrystalline materials prepared in the first synthesis run and later from grown crystals. The typical size of seeds used in growth was 3×3×303 \times3 \times30 mm. The pulling rate is 7 mm/h, and the seed rotation rate is 12 rpm. The growth was conducted in an Ar atmosphere to minimize the evaporation of Sn. After the growth, the single crystal was cooled down to room temperature with a ramp rate of 100-150 °C/h.

The crystal structure and chemical composition were characterized by X-ray diffraction (XRD) and scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS). XRD patterns were measured for single crystals and crushed powders using a Philips X’pert3 and Bruker D8 Discover X-ray diffractometer with Cu-Kα1\alpha_1 radiation (λ=0.15406\lambda= 0.15406 nm) in the range of 20-80°. The electronic transport measurements were performed with a 9T cryostat. The electrical contacts were made with silver paste/epoxy in a 4-probe configuration, and the field-dependent data were symmetrized. First principles calculations are performed using the Vienna Ab into Simulation Package (VASP). In this calculation, we used the projector augmented wave (PAW) method and the exchange-correlation functional obtained from the general gradient approximation (GGA). The fully structural optimization was done with 19×17×1519 \times17 \times15 k-mesh and cutoff energy 600 eV.

RESULTS & DISCUSSIONS

A series of runs were carried out to obtain single crystal Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} as described in Figure 1. The first run was the simple thermal process to obtain a polycrystalline seed. The seeds used for the second and third growths were obtained from the first and second growths, respectively. We have tried growth a total 5 times, but as the growth was repeated, the ratio of Cu to Sn was changed due to the evaporation of Sn. The best samples were obtained from the third growth.

Schematic of Czochralski growth of Cu$_3$Sn single crystal

Figure 1. Schematic of Czochralski growth of Cu3_3Sn single crystal. (a) Cu and Sn granular were melted in the 1st growth. (b) The obtained bulk Cu3_3Sn from the 1st growth was cut into a rectangular-shaped seed. (c) In the 2nd growth, the polycrystalline seed was used. (d-f) As-grown multicrystalline Cu3_3Sn was cut into the seed again and used for the 3rd, 4th, and 5th growths.

Figure 2(a) shows an optical image of the best Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} single crystal grown by the CZ method. The size of the crystal is around 1×1×31 \times1 \times3 cm3^{3}. Figure 2(b) and Figure 2(c) show the XRD pattern of Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} obtained from the second and third runs. Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} crystal obtained from the second run is found to have multiple grain domains, as shown in Figure 2(b). We noted that all XRD peaks found in the crystal from the second run are well matched with orthorhombic Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn}. The grains are mainly characterized by (102) and (321) orientations among the multiple domains.

Optical image and X-ray diffraction patterns of Cu$_3$Sn single crystals

Figure 2. (a) The optical image of obtained Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} single crystal. (b,c) X-ray diffraction (XRD) pattern of Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} crystals from the (b) 2nd growth and (c) 3rd growth. (d) Powder XRD pattern of the ground Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} single crystal. Black circles, solid red and blue lines show the observed intensity, the calculated pattern, and the difference between the observed and calculated patterns. Vertical green bars indicate the Bragg peak’s positions.

To obtain a better quality of Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} crystal, the third run was carried out by using the seed with multiple grains obtained from the second run. Most grains are eliminated, while only grains oriented in the (102) direction are left, as confirmed by XRD displayed in Figure 2(c). We note that the crystal grown in the (102) direction is unusual. This observation indicates that the (012) direction is the possibly preferred growth direction of Cu3Sn\mathrm{Cu}_3\mathrm{Sn}. The (012) direction is the most intense peak also measured in powder XRD, shown later.

The structural characterization of obtained Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystals is carried out using powder XRD. The XRD pattern of crushed crystals is analyzed using Rietveld refinement. Figure 2(d) shows the XRD data, Rietveld fit profile, Bragg positions, and difference in experimental and refined curve intensities. The power XRD shows sharp peaks only corresponding to orthorhombic Cu3Sn\mathrm{Cu}_3\mathrm{Sn}, suggesting that the sample is a single phase with good crystalline quality. The powder XRD data is well refined by the PmmnPmmn (No. 59) space group with lattice parameters of a=4.34a = 4.34 Å, b=4.86b = 4.86 Å, and c=5.48c = 5.48 Å, which are very close to the reported lattice parameter of Cu3Sn\mathrm{Cu}_3\mathrm{Sn} for the orthorhombic PmmnPmmn phase. More detailed information obtained from the refinement is shown in Table 1.

Atom positionxyzBisoB_{\mathrm{iso}}Occ
Cu1000.108666.721000.27871
Cu20004.509540.09486
Cu3000.491294.400540.10902
Cu400000
Sn100000

Table 1. Table 1. Detailed structural information on Cu3Sn\mathrm{Cu}_{3}\mathrm{Sn} single crystal obtained from Rietveld refinement parameters. The space group and lattice parameters are Pmnm\mathit{Pmnm}, a=4.34a=4.34 Å, b=4.86b=4.86 Å, c=5.48c=5.48 Å, and V=115.54V=115.54 Å3^{3}, respectively.

The chemical composition of the Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystal was analyzed by SEM-EDS. Figure 3(a) and Figure 3(b) shows a typical EDS spectrum and SEM image of a polished surface of the Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystal. Cu and Sn atoms are detected from the EDS spectrum. The composition is determined by averaging over 5 points of the same specimen on the polished surface and for several crystals. The average atomic ratio of the Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystal is Cu: Sn = 3.05:1. By considering the typical error of SEM/EDX (typical error ±5%\pm5\%), these results suggest that nearly stoichiometric crystals can be achieved by the CZ method. Furthermore, the result suggests that Cu3Sn\mathrm{Cu}_3\mathrm{Sn} crystals obtained from the CZ method are free from Sn contamination. The chemical homogeneity of Cu3Sn\mathrm{Cu}_3\mathrm{Sn} single crystal was further confirmed by elemental mapping, as displayed in Figure 3(c). The mapping was conducted on the sample surface with a dimension of about 10×810 \times8 μm2\mu\mathrm{m}^{2}. The results revealed a uniform distribution of Cu and Sn, suggesting that the surface of the Cu3Sn\mathrm{Cu}_3\mathrm{Sn} crystal is compositionally homogenous, at least within the spatial resolution of SEM-EDS measurement.

Energy-dispersive X-ray spectrum, scanning electron microscope image, and EDS element mapping of Cu₃Sn single crystal

Figure 3. (a) Energy-dispersive X-ray (EDS) spectrum of Cu3_3Sn single crystal, confirming the existence of Cu and Sn elements. The inset table shows weight and atomic percentage of Cu and Sn. (b) Scanning electron microscope image of Cu3_3Sn single crystal. (c) EDS element mapping of Cu3_3Sn single crystal, showing the distribution of Cu (left) and Sn (right).

In order to investigate the transport property of Cu3Sn\mathrm{Cu}_3\mathrm{Sn} crystals, measurements of the electrical resistivity and magnetoresistance were conducted. Since the crystals obtained by the CZ method are large (1×1×3 cm31 \times1 \times3\ \mathrm{cm}^{3}), the crystal was cut into a rectangular shape by electric discharge machining (EDM). The smallest dimension of the sample that can be prepared by EDM is ∼3×3×10 mm3\sim3 \times3 \times10\ \mathrm{mm}^{3}; however, the resistance of the sample was lower than the limit of the measurement device due to its high degree of metallicity of 0.10.1-0.3 μΩcm0.3\ \mu\Omega\mathrm{cm} at low temperature [5].

As a last resort to allow the transport measurements, the crystals were crushed into small pieces with a size of ∼0.3×0.3×1 mm3\sim0.3 \times0.3 \times1\ \mathrm{mm}^{3}. However, it was difficult to obtain accurate transport data of the tiny Cu3Sn\mathrm{Cu}_3\mathrm{Sn} pieces due to the unclear orientation and dimensions of the sample. The transport properties of Cu3Sn\mathrm{Cu}_3\mathrm{Sn} are highly dependent on the crystal orientation, as previously reported [5]. Although the crystal orientation of the measured piece is not well defined, intriguing transport properties similar to those reported previously have been observed [5].

Figure 4(a) displays the temperature dependence of resistance R(T)R(T) of the small Cu3Sn\mathrm{Cu}_3\mathrm{Sn} piece. Cu3Sn\mathrm{Cu}_3\mathrm{Sn} shows a metallic behavior and a power-law dependence at low temperatures. The solid red line is the fitted curve using R=ATαR = AT^{\alpha}. The estimated value of α\alpha from the best fit is 2.6, which agrees with the previous report [5]. Figure 4(b) shows magnetic field dependence of magnetoresistance (MR) at several temperatures. MR of Cu3Sn\mathrm{Cu}_3\mathrm{Sn} sample shows quasi-linear field dependence without saturation, which is again consistent with the previous result [5]. However, at high temperatures, the non-saturating quasi-linear MR gradually changes to conventional quadratic MR, indicating that the unusual MR of Cu3Sn\mathrm{Cu}_3\mathrm{Sn} is related to its low-energy electronic structure. Such behavior is usually an indication of non-trivial low-energy electronic structures, for example perfectly compensated electron/hole Fermi surface [14, 15], strong inhomogeneity-induced charge/mobility fluctuation [16], and topological Dirac/Weyl semimetals [17, 18, 19].

Temperature dependence of electrical resistance and resistance changes under magnetic field

Figure 4. (a) Temperature dependence of electrical resistance. The resistance can be fitted using a power-law dependence TαT^{\alpha} (α\alpha=2.6) (Red solid line). (b) Resistance changes under magnetic field up to 9 T at various temperatures.

Among the possibilities, the quasi-linear MR of Cu3_3Sn is likely due to its topological electronic band structure. In order to investigate the topological property of Cu3_3Sn, we examine the parity of each energy eigenstate at 8 time-reversal invariant momenta (TRIM) points displayed in the inset of Figure 5. Note that band degeneracy at 8 TRIM points except Γ and Y is 4 (including the spin degeneracy), so that parities at these TRIM points do not affect the topological Z2Z_2 index. Only at two TRIM points, Γ and Y, energy eigenstates are doubly degenerate (time-reversal pair) and their parities determine whether the Z2Z_2 index is trivial or not. Figure 5 presents the band dispersion of Cu3_3Sn with the inclusion of the spin-orbit coupling. It also shows band representations with parity eigenvalues at Γ and Y around the Fermi level. Table 2 shows the products of parity eigenvalues of the occupied states for high symmetry k-points in the bulk Brillouin zone. It clearly demonstrates that band/parity inversion occurs at Γ, thereby providing the nontrivial Z2Z_2 index. These results suggest that Cu3_3Sn is a non-trivial Z2Z_2 topological semimetal.

Electronic band-structure of orthorhombic Pmmn Cu3Sn along with some high symmetry directions

Figure 5. Electronic band-structure of orthorhombic Pmmn Cu3_3Sn along with some high symmetry directions. The corresponding Brillouin zone is displayed as an insert.

Γ\GammaYSXZTRUZ2Z_{2}
-1+1+1+1+1+1+1+1Nontrivial

Table 2. Table 2. The products of parity eigenvalues of the occupied states for high symmetry k-points in the bulk Brillouin zone displayed in the inset of Figure 5. Note that core bands are excluded in the products of parity eigenvalues. Band (parity) inversion occurs at Γ\Gamma, thereby providing the nontrivial Z2Z_{2} index.

CONCLUSION.

In summary, high-quality Cu3_3Sn single crystals in cm-size are successfully synthesized by the CZ method. The structural and chemical composition measurements confirm the high quality and homogeneity of Cu3_3Sn crystals. Although the electronic transport properties were not precisely measured due to the difficulties in sample preparation, non-saturating quasi-liner MR, which supports the possibility of Dirac band, and is in good agreement with previous reports, was successfully observed. However, more efforts to prepare samples with well-defined geometries and crystal orientations are needed to gain better insight into the topological properties of Cu3Sn\mathrm{Cu}_3\mathrm{Sn}. The large-sized single crystals free from contamination of Sn flux will enable the various measurements, including neutron scattering, magnetization, specific heat, and optical conductivity, thereby promoting more in-depth studies of the topological properties of Cu3Sn\mathrm{Cu}_3\mathrm{Sn}.

Acknowledgment

This research was supported by PNU-RENovation (2021-2022).

References

  1. [1]H. Zhu, C. A. Richter, E. Zhao, J. E. Bonevich and W. A. Kimes et al, Topological insulator Bi₂Se₃ nanowire high performance field-effect transistor, Sci. Rep. 3, 1757 (2013). https://doi.org/10.1038/srep01757
  2. [2]J. Tominaga, R. E. Simpson, P. Fons and A. V. Kolobov, Electrical-field induced giant magnetoresistivity in (non-magnetic) phase change films, Appl. Phys. Lett. 99, 152105 (2011). https://doi.org/10.1063/1.3651275
  3. [3]G. Ghosh and M. Asta, Phase Stability, Phase Transformations, and Elastic Properties of Cu₆Sn₅: Ab initio Calculations and Experimental Results, J. Mater. Res 20, 3102 (2011). https://doi.org/10.1557/JMR.2005.0371
  4. [4]C. Liu, B. Li, Y. Ge, W. H. Jiao and C. Xi, et al, arXiv, https://arxiv.org/abs/2205.04307 (accessed 9 May 2022).
  5. [5]N. Karlsson, An x-ray study of the phases in the copper-titanium system, J. Inst. Met. 79, 391 (1951).
  6. [6]P.L. Brooks and E. Gillam, THE EPSILON-PHASE IN THE CU-SN SYSTEM, Acta Metall 18, 1181 (1970).
  7. [7]X. Sang, K. Du and H. Ye, An ordered structure of Cu₃Sn in Cu–Sn alloy investigated by transmission electron microscopy, J. Alloy. Comp 469 129 (2009). https://doi.org/10.1016/j.jallcom.2008.01.107
  8. [8]H. Knødler, The crystalline structure and structural relationship of the gamma and epsilon phases in the system Cu-Sn, Metall 20 82 (1966).
  9. [9]T. Zhang, Y. Jiang, Z. Song, H. Huang and Y. He et al, Catalogue of topological electronic materials, Nature 566, 475 (2019). https://doi.org/10.1038/s41586-019-0944-6
  10. [10]K. L. Chopra and S. K. Bahl, Hall Effect in Thin Metal Films, J. Phys. D 38, 3607 (1967). https://doi.org/10.1063/1.1710180
  11. [11]C. D. Brandle, Czochralski growth of oxides, J. Cryst. Growth 264, 593 (2004). https://doi.org/10.1016/j.jcrysgro.2003.12.044
  12. [12]K. Prokeš, Y.-K. Huang, M. Reehuıs, B. Klemke and J.-U. Hoffmann et al, Electronic properties of a heavy-fermion U(Ru₀.₉₂Rh₀.₀₈)₂Si₂ single crystal, Phys. Rev. B 95, 035138 (2017). https://doi.org/10.1103/PhysRevB.95.035138
  13. [13]V. A. Dyadkin, S. V. Grigoriev, D. Menzel, D. Chernyshov and V. Dmitriev, Control of chirality of transition-metal monosilicides by the Czochralski method, Phys. Rev. B 84, 014435 (2011). https://doi.org/10.1103/PhysRevB.84.014435
  14. [14]F. Y. Yang, K. Liu, K. Hong, D. H. Reich and P. C. Searson et al, Large Magnetoresistance of Electrodeposited Single-Crystal Bismuth Thin Films, Science 284, 1335 (1999). https://doi.org/10.1126/science.284.5418.1335
  15. [15]M. N. Ali, J. Xiong, S. Flynn, J. Tao and O. D. Gibson et al, Large, non-saturating magnetoresistance in WTe₂, Nature (London) 514, 205 (2014). https://doi.org/10.1038/nature13763
  16. [16]R. Xu, A. Husmann, T. F. Rosenbaum, M.-L. Saboungi and J. E. Enderby et al, Large magnetoresistance in non-magnetic silver chalcogenides, Nature (London) 390, 57 (1997). https://doi.org/10.1038/36306
  17. [17]T. Liang, Q. Gibson, M. N. Ali, M. Liu, R. J. Cava, and N. P. Ong, Ultrahigh mobility and giant magnetoresistance in the Dirac semimetal Cd₃As₂, Nat. Mater. 14, 280 (2015). https://doi.org/10.1038/nmat4143
  18. [18]W. Gao, N. Hao, F.-W. Zheng, W. Ning and M. Wu et al, Extremely Large Magnetoresistance in a Topological Semimetal Candidate Pyrite PtBi₂, Phys. Rev. Lett. 118, 256601 (2017). https://doi.org/10.1103/PhysRevLett.118.256601
  19. [19]J. M. Ok, N. Mohanta, J. Zhang, S. Yoon, S. Okamoto et al, Correlated oxide Dirac semimetal in the extreme quantum limit, Sci. Adv. 7, eabf9631 (2021). https://doi.org/10.1126/sciadv.abf9631

Paper details

vlnc:W_5xqh79dn
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents