betaFeedback

WorksPhysics and Astronomy

New polymorph γ-CuWO4 inspired by γ-CuMoO4: experimental identification and theoretical verification

Abstract

In the context of our efforts to develop hydrogen gas sensors, two samples of ternary CuWO4 with the same crystalline structure have been prepared by two different non-equilibrium techniques. We show that the materials' structure is significantly different from the known stable one, and we identify that it is very similar to that of previously reported γ-CuMoO4. We use ab initio calculations to confirm that the newly identified phase, γ-CuWO4, represents a local energy minimum. We present very similar calculated and measured lattice constants and X-ray diffractograms. We make a case that the low-temperature formation of the metastable γ-CuWO4 phase is facilitated by easier kinetics and/or by Cu-rich composition of our samples, and we show that it converts to the stable phase after annealing to 600 °C.

Main text

There are worldwide efforts [1, 2] to continuously improve the performance of semiconductor metal oxide-based gas sensors, for various applications in the field of hydrogen economy, environmental monitoring, breath monitoring or food analysis. The sensors are of particular interest at the nanometer scale, where the large surface-to-volume ratio significantly improves their sensitivity. Further progress has been achieved by moving from homogeneous metal oxides to nanocomposites, nanostructures, heterojunctions and core-shell nanoparticles (NPs), which combine two semiconductors such as n-type WO3_3 and p-type CuO [3, 4, 5, 6, 7, 8, 9, 10, 11, 12]. Sensing of a wide range of gases has been reported using this pair of materials, ranging from hydrogen [12] and hydrogen sulfide [10] through ammonia [6] or acetone [5] to xylene [3] or sarin [9].

In this context, we are making efforts to prepare WO3_3+CuO based sensors by two different deposition techniques which realize two different designs: (i) film of WO3_3 on nanoparticles of CuO and (ii) alternating monolayers of nanoparticles of WO3_3 and nanoparticles of CuO. In both cases, the research includes annealing of the as-deposited sensors to various temperatures in synthetic air. While the sensing performance of the materials and devices obtained will be published separately, the present paper deals with one of these materials itself. We have found that at a temperature of at most 400 °C, a new polymorph, referred to as γ\gamma-CuWO4_4 throughout this paper, formed at the interface of WO3_3 and CuO. The structure of this polymorph is significantly different from that of the known stable phase which is usually given without any Greek letter and which we refer to as α\alpha-CuWO4_4 for distinguishing purposes. However, the structure of the newly identified polymorph is very similar to the known γ\gamma-CuMoO4_4 phase.

The aim of this paper is to examine the existence of the newly identified polymorph γ\gamma-CuWO4_4, to specify under which conditions did it form, to confirm that it constitutes a local energy minimum according to ab-initio calculations, and to check whether it converts to stable α\alpha-CuWO4_4 after annealing to a sufficiently high temperature. In addition to a possible usefulness of γ\gamma-CuWO4_4 itself, the presented information is expected to be useful for the correct interpretation of results obtained by the numerous practitioners dealing with the aforementioned devices based on WO3_3+CuO.

The sample based on a combination of a thin film of WO3_3 on CuO NPs was prepared in two steps. First, the NPs were prepared utilizing a magnetron-based gas aggregation source (MGAS). The MGAS (HVM Plasma) was attached to a main deposition chamber, where a silicon substrate was mounted to a rotating substrate holder kept at a room temperature. The MGAS featured of a cylindrical magnetron equipped with a 50 mm diameter Cu target placed inside a cylindrical aggregation chamber measuring 100 mm in diameter, terminated by a conical ending with a 4 mm diameter orifice. The NPs were prepared in Ar atmosphere at an Ar flow rate of 100 sccm and a pressure of 80 Pa. The magnetron was driven in DC mode and operated at a constant discharge power of 100 W. Second, 40 nm thin film of WO3_3 was deposited on top of the NPs using another magnetron-based sputtering system (Leybold-Heraeus LH Z400). This film was deposited using a magnetron with a 72 mm diameter W target powered by a DC power supply operated at a constant power mode of 60 W. The total pressure of the Ar + O2_2 working atmosphere was 614 mPa and the corresponding flow rates of Ar and O2_2 were 15.0 and 3.75 sccm, respectively. During the deposition, the sample was heated to 400 °C. Let us note that the NPs were prepared as metal NPs during the first step, but they oxidezed to CuO during their exposure to the ambient atmosphere when the sample was transferd to the second system and also during the deposition process of the WO3_3 film. More details about the experimental setups can be found in Refs. [12, 13].

The sample based on alternating monolayers of WO3_3 and CuO NPs was deposited using another MGAS (Nanogen-Trio, Mantis deposition) equipped with three 1” magnetrons placed inside a cylindrical aggregation chamber with a diameter of 120 mm, terminated by a domed ending with a 4 mm diameter orifice. In this experiment, Cu and W metallic targets were used. This MGAS was also attached to a main deposition chamber, where a silicon substrate was mounted to a rotating substrate holder kept at a room temperature. The NPs were prepared in Ar + O2_2 atmosphere at the total pressure of 60 Pa. The Ar flow rate was 100 sccm. The flow rates of O2_2 were 1.3 and 1.5 sccm for WO3_3 and CuO NPs, respectively. Both magnetrons were driven with DC power supply (GEN 600-1.3, TDK-Lambda) operated at a constant discharge power of 25 W. The deposition rate was regularly monitored during the deposition by crystal microbalance (STM-2, Inficon). This enabled switching among the deposition of copper oxide and tungsten oxide NPs in a precisely defined ratio. The system was orchestrated with a custom-built LabVIEW system. More details about this system can be found in Ref. [14].

Both kinds of samples were post-annealed in a furnace in synthetic air at an ambient pressure at 400, 500 and 600°C for 6 hours.

The structural characterization was performed by X-ray diffraction measurements, using an X’Pert PRO (PANalytical) instrument with Cu Kα radiation (λ=0.154187\lambda= 0.154187 nm). All data evaluation was performed using the PANalytical ware package HighScore Plus. The evaluation included the Rietveld analysis: least-square fit of lattice vectors of γ-CuWO4_4 on its measured X-ray diffractogram, using calculated crystal coordinates of atoms.

All ab-initio density-functional theory simulations were performed by the Quantum Espresso code [15]. The main simulation algorithm was a simultaneous relaxation of all lattice vectors and all 36 atomic positions of γ-CuWO4_4, using those of γ-CuMoO4_4 as a starting point. Two simulation techniques were employed. First, the exchange and correlation energy was represented by the PBE (Perdew–Burke–Ernzerhof) functional [16], the atom cores and inner electron shells were represented by standard Vanderbilt-type ultrasoft pseudopotentials, the energy cutoff was 30 Ry and the electronic density cutoff was 360 Ry. The optimization was controlled by convergence threshold on total energy (10−410^{-4} Ry), convergence threshold of forces (10−310^{-3} Ry/bohr) and, most importantly, convergence threshold on |stress| (10 MPa, compared to ≈10 GPa after the replacement of Mo by W in γ-CuMoO4_4; the last criterion to be fulfilled). Second, the exchange and correlation energy was for comparative purposes represented also by the PBEsol (PBE revised for solids) functional [17], the corresponding Vanderbilt (W) and PAW (projector augmented wave; Cu and O) pseudopotentials were taken from the online database [18], the energy cutoff was 90 Ry and the electronic density cutoff was 720 Ry. Reducing the total stress to less than 200 MPa (approaching or being below usual stresses in experimentally prepared films) turned out to be sufficient to conclude that the difference between measured and calculated lattice parameters is for both simulation techniques smaller than the difference between these two calculated results.

All simulations were spin-polarized. The lowest-energy ferrimagnetic configuration of γ\gamma-CuWO4_4 (see below) has been identified before and used as a part of the starting point of the variable-cell geometry optimization, by performing the initial fixed-cell geometry optimization 6×6 \times with 6 different starting points. The starting points included a non-magnetic configuration and 5 ferrimagnetic configurations. Two of these six initial configurations (one inspired by γ\gamma-CuMoO4_4, and another one which converged to the same magnetic state after some of the atoms changed the sign of their magnetic moments) led to the identical final configuration with the lowest energy. Similar simulations of the known α\alpha-CuWO4_4 phase in its lowest-energy antiferromagnetic configuration were performed for comparison.

The X-ray diffraction patterns of both samples prepared are shown in Figure 1. As indicated above, the interdiffusion of binary amorphous WO3_3 and CuO after annealing to 400 °C leads to a formation and crystallization of ternary CuWO4_4, characterized by diffraction patterns very far from that of conventionally expected triclinic α\alpha-CuWO4_4 (PDF #04-009-6293; space group P1ˉP\bar{1}). The difference cannot be explained by parallel crystallization of other phases such as CuO (PDF #00-048-1548; space group C2/c). However, the diffraction patterns obtained are very similar to those of triclinic γ\gamma-CuMoO4_4. Note that there are two γ\gamma-CuMoO4_4 PDF records #01-088-0619 and #04-009-2227 (space group P1ˉP\bar{1}), very similar except different choices which vector is labelled a/b/c in the corresponding primary source (we use the labelling from the latter one). Furthermore, the atomic coordinates in γ\gamma-CuMoO4_4 according to powder diffraction files [19] and according to the widely used online database [20] can be converted to each other after replacing some coordinates by their complement to 1 and after exchanging Cu and Mo atoms in the x-direction.

X-ray diffractograms and calculated peak positions for CuWO₄ phases

Figure 1. The first and third line from the bottom show X-ray diffractograms (Cu Kα\alpha radiation) of samples annealed to 400 °C, dominated by the newly identified metastable γ\gamma-CuWO4_4 phase. See the calculated peak positions and relative intensities in the top line, similar to those of γ\gamma-CuMoO4_4 (PDF #01-088-0619 or equivalently #04-009-2227; space group P1ˉP\bar{1}). The second and fourth line from the bottom show X-ray diffractograms of samples annealed to 600 °C, dominated by the known stable α\alpha-CuWO4_4 phase (PDF #04-009-6293; also space group P1ˉP\bar{1}). There are two kinds of samples: WO3_3 film on CuO NPs (top dashed oval) and alternating monolayers of WO3_3 NPs and CuO NPs (bottom dashed oval). Although the whole samples are prone to be Cu-rich, the differences in diffractograms cannot be explained by a presence of CuO (PDF #00-048-1548; space group C2/c).

Thus, a case can be made that γ\gamma-CuMoO4_4 is a prototype of a newly created metastable γ\gamma-CuWO4_4 phase. The similarity of the 36-atom primitive cells and in turn X-ray diffractograms is supported by the fact that 30 atoms are the same and the remaining 6 atoms are not only in the same group, but within ≈0.5%\approx0.5\% also of the same size. Compare the lattice constants of bcc-Mo of 3.147 Å and bcc-W of 3.165 Å, and note that the extra shell of valence electrons of W is almost compensated by 14 extra protons (the period of W includes lanthanoids, the period of Mo does not) attracting these electrons to the atomic core.

In order to confirm that γ\gamma-CuWO4_4 constitutes at least a local energy minimum, ab-initio simulations have been performed. The simulations were complemented by the Rietveld analysis of one of the X-ray diffractograms obtained. All resulting lengths of lattice vectors and angles between them are provided in Table 1. It can be seen that all four sets of available values (γ\gamma-CuWO4_4 according to the Rietveld analysis, γ\gamma-CuWO4_4 according to the simulations using PBE and PBEsol functional and even γ\gamma-CuMoO4_4) are very similar. The values of aa, bb and cc are within ±1.2%\pm1.2\%, the values of α\alpha, β\beta and γ\gamma are within ±0.4%\pm0.4\% and the values of cos⁡α\cos\alpha, cos⁡β\cos\beta and cos⁡γ\cos\gamma are within ±3.2%\pm3.2\%. Furthermore, the differences of aa, bb and cc between given lines are predominantly in the same direction, preserving the shape of the primitive cell. For example, the values of aa, bb and cc of γ\gamma-CuWO4_4 obtained using the PBE functional (implementation of the generalized gradient approximation, known to overestimate rather underestimate lattice constants) are 100-102% of those obtained by the Rietveld analysis. The values of aa, bb and cc obtained using the PBEsol functional (specifically tailored to improve the structural properties of solids) are 99-100% of those obtained by the Rietveld analysis. Thus, the presented measured and calculated data (i) mutually support each other and (ii) support the statement that the prototype of the γ\gamma-CuWO4_4 material obtained is γ\gamma-CuMoO4_4. Note that the differences between modelling and experiment are actually smaller than the mutual differences between both modelling techniques used. For example, the calculated volume per atom is 103.4% (PBE functional) and 98.6% (PBEsol functional) of the experimental one, at a difference between PBE and PBEsol of 4.8%.

MaterialSourceaa (Å)bb (Å)cc (Å)α\alpha (°)β\beta (°)γ\gamma (°)Atoms per cellVolume per atom (Å3^3)
α\alpha-CuWO4_4Experiment (PDF #04-009-6293)4.7035.8394.87891.6892.4782.811211.061
γ\gamma-CuMoO4_4Experiment (PDF #04-009-2227)6.3067.9789.710103.27103.2194.763612.726
γ\gamma-CuWO4_4Experiment (Rietveld analysis)6.3518.0299.688102.77104.0894.813612.843
γ\gamma-CuWO4_4Ab-initio (PBE functional)6.3568.1219.888103.57103.2794.603613.278
γ\gamma-CuWO4_4Ab-initio (PBEsol functional)6.2887.9359.711102.71103.2494.563612.660

Table 1. Characteristics of triclinic (space group P1ˉP\bar{1} in all cases) CuMoO4_4 and CuWO4_4 phases mentioned in the text.

The atomic structure of γ\gamma-CuWO4_4 is visualized in Figure 2, and the corresponding atomic coordinates are given in Table 2. See the trilayer structure consisting of almost planar (0,1ˉ,1)(0,\bar{1},1) layers (from the top left to the bottom right corner of Figure 2) of CuWO3_3, CuWO3_3 and O2_2. Moreover, there are triplets of almost planar (0,1,0)(0,1,0) layers of Cu atoms carrying magnetic moments of opposite signs (horizontal in Figure 2; 1×1\times orange Cu+ and 2×2\times yellow Cu−) and being responsible for the ferrimagnetism of γ\gamma-CuWO4_4. Note the different local environment of Cu+ and Cu− atoms in terms of O-Cu-O angles. Next, the calculated lattice vectors and atomic coordinates were used to predict an X-ray diffractogram using an arbitrary full width at half maximum of 0.1414°, and this diffractogram is compared with one of the experimental ones in Figure 3. It is clear that despite the numerous sources of potential differences (finite exactness of ab-initio calculations, off-stoichiometric composition in the experiment, preferred orientation in the experiment), the diffractograms are very similar.

Calculated structure of triclinic gamma-CuWO4

Figure 2. Calculated (top line in Fig. 1) structure of triclinic (space group P1ˉP\bar{1}) γ\gamma-CuWO4_4. Yellow and orange balls are Cu atoms carrying magnetic moments of opposite signs, black balls are W atoms and white balls are O atoms. There are 4×2×24\times2\times2 36-atom primitive cells and the view direction is slightly off x-axis.

Atomxxyyzz
Cu+0.0733950.4708970.666430
Cu-0.2211780.2332970.436402
Cu-0.5966840.1995550.003486
W0.0900520.1163420.892554
W0.4318460.4556770.227344
W0.7203020.1276310.348393
O0.0017280.0774410.273005
O0.0467850.2836520.806048
O0.0591100.7007840.521798
O0.1394080.8960540.022150
O0.1917110.4566190.296525
O0.2912060.0244080.548759
O0.3207610.2442370.061347
O0.3431980.4144440.614311
O0.3724890.0311360.845849
O0.3976930.6035300.118059
O0.4705690.2278830.355280
O0.7111320.3396530.200659

Table 2. Calculated (top line in Figure 1) crystal coordinates of atoms in the γ\gamma-CuWO4_4 phase. There are 36 atoms in a primitive cell of a space group P1ˉP\bar{1}, i.e. each line represents two atoms with crystal coordinates x,y,zx,y,z and −x,−y,−z-x,-y,-z. The signs of Cu+ and Cu- represent ferrimagnetism.

Comparison of experimental and predicted X-ray diffractograms

Figure 3. Comparison of an experimental X-ray diffractogram (Cu Kα\alpha radiation; blue; bottom line from Figure 1 after subtracting the background) and a predicted X-ray diffractogram (purple; top line from Figure 1 after converting the delta functions to peaks with a full width at half maximum of 0.1414°).

Let us recall the metastable nature of γ\gamma-CuWO4_4. This has been also confirmed by ab-initio calculations (PBE functional): the formation energy of α\alpha-CuWO4_4 (-1.563 eV/at. compared to fcc-Cu + bcc-W + O2_2) is of 5 meV/at. lower than that of γ\gamma-CuWO4_4 (-1.558 eV/at.). Thus, it is relevant to discuss possible reasons for the formation of this metastable phase. First, let us point out the overall non-equilibrium nature of the preparation techniques such as sputtering. The importance of that is further supported by the fact that the aforementioned energy difference of 5 meV/at is actually rather low, compared to energy differences between polymorphs of many other materials.

Second, as the samples analyzed were not prepared in order to contain α\alpha- or γ\gamma-CuWO4_4 but in order to be good sensors, their overall [Cu]/[W] compositional ratio is higher than 1. In particular, about the same volume of alternating nanoparticles of WO3_3 (≈54\approx54 Å3^3 per metal atom) and nanoparticles of CuO (≈21\approx21 Å3^3 per metal atom) leads to a higher number of Cu atoms. Although the agreement of modelling and experiment (Table 1 and Figure 3) indicates that the [Cu]/[W] ratio in the γ\gamma-CuWO4_4 phase (which constitutes only part of the samples) is very close to 1, the preference to form γ\gamma-CuWO4_4 rather than α\alpha-CuWO4_4 may be nevertheless enhanced under Cu-rich conditions. We made efforts to support also this hypothesis by ab-initio calculations. Indeed, when one of the six W atoms in the 36-atom cell of γ\gamma-CuWO4_4 and in a 1×1×31\times1\times3 36-atom supercell of α\alpha-CuWO4_4 is replaced by Cu, the energy of γ\gamma-CuWO4_4, originally of 5 meV/at. higher, becomes of ≈\approx5 meV/at. lower than that of α\alpha-CuWO4_4. The key information is not the latter number itself (one arbitrary composition, possible role of distribution of Cu atoms in the W sublattice, poorer convergence for the fictitious Cu-rich composition than for the ideal one), but the direction in which the energy difference changes.

Third, note that γ\gamma-CuWO4_4 is of ≈\approx16% less dense phase than α\alpha-CuWO4_4 (volumes per atom in Table 1). Thus, it is reasonable to assume that while α\alpha-CuWO4_4 is slightly more thermodynamically stable, the low-temperature preparation of γ\gamma-CuWO4_4 is significantly kinetically easier. This is a well known phenomenon reported for other materials (to put one example: easier growth of low-density metastable γ\gamma-Al2_2O3_3 compared to high-density stable α\alpha-Al2_2O3_3). The low-temperature preparation may be quantified by the following: metastable γ\gamma-CuWO4_4 formed during the annealing up to 400 °C as shown by two of the diffractograms in Figure 1, remained stable up to at least 500 °C (not shown), but converted to stable α\alpha-CuWO4_4 after annealing to 600 °C (possibly in parallel to changing its composition from slightly Cu-rich to stoichiometric - previous paragraph) as shown by the other two diffractograms in Figure 1.

To conclude, a new polymorph γ\gamma-CuWO4_4, having a triclinic lattice (space group P1ˉP\bar{1}) very similar to its γ\gamma-CuMoO4_4 prototype, has been obtained by annealing the boundary between WO3_3 and CuO. Ab-initio simulations confirm the existence of this phase, confirm its slight metastability compared to α\alpha-CuWO4_4, and allowed us to predict the atomic positions and in turn an X-ray diffractogram very similar to the experimental one. While the formation of γ\gamma-CuWO4_4 during the annealing to 400 °C could be supported by its lower density and possibly also by slightly Cu-rich composition, it converts to α\alpha-CuWO4_4 when annealed to 600 °C. In addition to a possible usefulness of γ\gamma-CuWO4_4 itself, the findings are expected to contribute to a correct interpretation of results obtained in the course of worldwide efforts to prepare gas sensors of various architectures combining WO3_3 and CuO.

This work was supported by the project Quantum materials for applications in sustainable technologies (QM4ST), funded as project No. CZ.02.01.01/00/22_008/0004572 by Programme Johannes Amos Comenius, call Excellent Research. Computational resources were provided by the e-INFRA CZ project (ID:90254), supported by the Ministry of Education, Youth and Sports of the Czech Republic.

References

  1. [1]D. Nunes, A. Pimentel, A. Gonçalves, S. Pereira, R. Branquinho, P. Barquinha, E. Fortunato, R. Martins, Metal oxide nanostructures for sensor applications, Semicond. Sci. Tech. 34 (2019) 043001, doi.org/10.1088/1361-6641/ab011e.DOI
  2. [2]X.X. Li, L. Fu, H. Karimi-Maleh, F. Chen, S.C. Zhao, Innovations in WO₃ gas sensors: Nanostructure engineering, functionalization, and future perspectives, Heliyon 10 (2024) e27740, doi.org/10.1016/j.heliyon.2024.e27740.DOI
  3. [3]M.M. Guo, N. Luo, Y. Chen, Y. Fan, X.H. Wang, J.X. Xu, Fast-response MEMS xylene gas sensor based on CuO/WO₃ hierarchical structure, J. Hazard. Mater. 429 (2022) 127471, doi.org/10.1016/j.jhazmat.2021.127471.DOI
  4. [4]L. Yin, G.P. Qu, P. Guo, R. Zhang, J. Sun, D.L. Chen, Construction and enhanced low-temperature H₂S-sensing performance of novel hierarchical CuO@WO₃ nanocomposites, J. Alloys Compd. 785 (2019) 367-373, doi.org/10.1016/j.jallcom.2019.01.037.DOI
  5. [5]F.C. Yang, F.Y. Wang, Z.G. Guo, Characteristics of binary WO₃@CuO and ternary WO₃@PDA@CuO based on impressive sensing acetone odor, J. Colloid Interface Sci. 524 (2018) 32-41, doi.org/10.1016/j.jcis.2018.04.013.DOI
  6. [6]W.J. Yan, M. Hu, Vertically Aligned WO₃-CuO Core-Shell Nanorod Arrays for Ultrasensitive NH₃ Detection, Nano 13 (2018) 1850122, doi.org/10.1142/S1793292018501229.DOI
  7. [7]M. He, L.L. Xie, X.L. Zhao, X.B. Hu, S.H. Li, Z.G. Zhu, Highly sensitive and selective H₂S gas sensors based on flower-like WO₃/CuO composites operating at low/room temperature, J. Alloys Compd. 788, 36-43 (2019), doi.org/10.1016/j.jallcom.2019.01.349.DOI
  8. [8]Y. Wang, S.Y. Zhang, D.K. Xiao, S.J. Wang, T. Zhang, X. Yang, S.Q. Heng, M.J. Sun, CuO/WO₃ hollow microsphere P-N heterojunction sensor for continuous cycle detection of H₂S gas, Sensor Actuat. B-Chem. 374 (2022) 132823, doi.org/10.1016/j.snb.2022.132823.DOI
  9. [9]K.T. Alali, J.Y. Liu, K. Aljebawi, P.L. Liu, R.R. Chen, R.M. Li, H.Q. Zhang, L.M. Zhou, J. Wang, Electrospun n-p WO₃/CuO heterostructure nanofibers as an efficient sarin nerve agent sensing material at room temperature, J. Alloys Compd. 793 (2019) 31-41, doi.org/10.1016/j.jallcom.2019.04.157.DOI
  10. [10]N.S. Ramgir, C.P. Goyal, P.K. Sharma, U.K. Goutam, S. Bhattacharya, N. Datta, M. Kaur, A.K. Debnath, D.K. Aswal, S.K. Gupta, Selective H₂S sensing characteristics of CuO modified WO₃ thin films, Sensor Actuat. B-Chem. 188 (2013) 525-532, doi.org/10.1016/j.snb.2013.07.052.DOI
  11. [11]R.K. Jain, A. Khanna, CuO-doped WO₃ thin film H₂S sensors, Sensor Actuat. B-Chem. 343 (2021) 130153, doi.org/10.1016/j.snb.2021.130153.DOI
  12. [12]S. Haviar, J. Capek, S. Batkova, N. Kumar, F. Dvorak, T. Duchon, M. Fialova, P. Zeman, Hydrogen gas sensing properties of WO₃ sputter-deposited thin films enhanced by on-top deposited CuO nanoclusters, Int. J. Hydrogen Energy 43 (2018) 22756-22764, doi.org/10.1016/j.ijhydene.2018.10.127.DOI
  13. [13]Š. Batková, T. Kozák, S. Haviar, P. Mareš, J. Čapek, Effect of exit-orifice diameter on Cu nanoparticles produced by gas-aggregation source, Surf. Coatings Technol. 417 (2021) 127196, doi.org/10.1016/j.surfcoat.2021.127196.DOI
  14. [14]K. Shaji, S. Haviar, P. Zeman, Š. Kos, R. Čerstvý, J. Čapek, Controlled sputter deposition of oxide nanoparticles-based composite thin films, Surf. Coatings Technol. 477 (2024) 130325, doi.org/10.1016/j.surfcoat.2023.130325.DOI
  15. [15]P. Giannozzi, O. Andreussi, T. Brumme, O. Bunau, M. Buongiorno Nardelli, M. Calandra, R. Car, C. Cavazzoni, D. Ceresoli, M. Cococcioni, N. Colonna, I. Carnimeo, A. Dal Corso, S. de Gironcoli, P. Delugas, R. A. DiStasio Jr, A. Ferretti, A. Floris, G. Fratesi, G. Fugallo, R. Gebauer, U. Gerstmann, F. Giustino, T. Gorni, J. Jia, M. Kawamura, H. Y. Ko, A. Kokalj, E. Küçükbenli, M. Lazzeri, M. Marsili, N. Marzari, F. Mauri, N. L. Nguyen, H. V. Nguyen, A. Otero-de-la-Roza, L. Paulatto, S. Poncé, D. Rocca, R. Sabatini, B. Santra, M. Schlipf, A. P. Seitsonen, A. Smogunov, I. Timrov, T. Thonhauser, P. Umari, N. Vast, X. Wu, S. Baroni, Advanced capabilities for materials modelling with Quantum ESPRESSO, J. Phys.: Condens. Matter 29 (2017) 465901, www.quantum-espresso.org.
  16. [16]J.P. Perdew, K. Burke, M. Ernzerhof, Generalized Gradient Approximation Made Simple, Phys. Rev. Lett. 77 (1996) 3865-3868, doi.org/10.1103/PhysRevLett.77.3865.pubmed.ncbi.nlm.nih.gov/10062328
  17. [17]J.P. Perdew, A. Ruzsinszky, G.I. Csonka, O.A. Vydrov, G.E. Scuseria, L.A. Constantin, X. Zhou, K. Burke, Restoring the Density-Gradient Expansion for Exchange in Solids and Surfaces, Phys. Rev. Lett. 100 (2008) 136406, doi.org/10.1103/PhysRevLett.100.136406.pubmed.ncbi.nlm.nih.gov/18517979
  18. [18]https://www.materialscloud.org/discover/sssp/table/precision
  19. [19]JCPDS-ICDD 2015 PDF-4+ Database (Newton Square, PA: International Centre for Diffraction Data).
  20. [20]https://next-gen.materialsproject.org/materials/mp-619545.

Paper details

vlnc:W_85y4c6dx
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents