betaFeedback

WorksPhysics and Astronomy

Rock-salt ScN(113) layers grown on AlN(112ˉ2)(11\bar{2}2) by plasma-assisted molecular beam epitaxy

Abstract

Transition-metal nitrides constitute a versatile class of materials with diverse properties and wide-ranging applications. Exploring new surface orientations and uncovering novel properties can enable innovative material configurations with tailored functionalities for device integration. Here, we report the growth and characterization of (85-210)-nm-thick undoped ScN layers on AlN(112ˉ2)(11\bar{2}2)/Al2_{2}O3_{3}(101ˉ0)(10\bar{1}0) templates via plasma-assisted molecular beam epitaxy. X-ray diffractometry and transmission electron microscopy confirm a pure (113) surface orientation with rotational twins. Two distinct in-plane relationships between ScN(113) and AlN(112ˉ2)(11\bar{2}2) have been identified: the dominant [11ˉ0]ScN∥[1ˉ1ˉ23]AlN[1\bar{1}0]_{\mathrm{ScN}} \parallel [\bar{1}\bar{1}23]_{\mathrm{AlN}} and [332ˉ]ScN∥[11ˉ00]AlN[33\bar{2}]_{\mathrm{ScN}} \parallel [1\bar{1}00]_{\mathrm{AlN}} (under tensile-compression), and the less prevalent [1ˉ2ˉ1]ScN∥[11ˉ00]AlN[\bar{1}\bar{2}1]_{\mathrm{ScN}} \parallel [1\bar{1}00]_{\mathrm{AlN}} and [74ˉ1ˉ]ScN∥[1ˉ1ˉ23]AlN[7\bar{4}\bar{1}]_{\mathrm{ScN}} \parallel [\bar{1}\bar{1}23]_{\mathrm{AlN}} (under biaxial compression). Broad photoluminescence spectra with a peak emission energy of ≈2.16 eV\approx 2.16\,\mathrm{eV} originate from the lowest direct gap at the X\mathbf{X} point of the ScN band structure. Temperature-dependent Hall-effect measurements (4-380 K) reveal that impurity band conduction dominates. The electron mobility is primarily limited by optical phonon scattering, characterized by an effective phonon energy of (60±3) meV(60 \pm 3)\,\mathrm{meV}.

Introduction

Transition-metal group-3 (or -IIIB) nitrides (TMNs), such as ScN, YN, NbN, HfN, etc., constitute a versatile class of materials with diverse properties and applications.[1, 2, 3, 4, 5, 6] ScN and other TMNs are refractory materials combining high mechanical strength (e.g., the hardness of ScN ≈ 21 GPa[7]) and high-temperature stability (e.g., the melting point of ScN ≈ 2600 °C[8]), making them suitable for applications in harsh environments. Theoretical studies conducted for the (001) and (111) surfaces of ScN (together with other rocksalt TMNs like HfN, MoN, and TaN) suggest that ScN, either alone[2] or combined with noble metals like Pt and Pd,[4] is a promising candidate for low-cost catalysts for the hydrogen evolution reaction, contributing to renewable and environmental sustainability. ScN has also been utilized in combination with other TMNs, such as ZrN/ScN, HfN/ScN and (Zr,W)N/ScN, for Schottky diode-based thermionic energy conversion.[9, 10] Additionally, the observed high thermoelectric efficiency suggests that ScN is a promising candidate for high-temperature thermoelectric applications.[11, 12, 13] ScN has been found to have a high Mn solubility, making it a good candidate for magnetic semiconductors.[14, 15, 16] Furthermore, the high refractive index and strong carrier absorption of ScN at the infrared spectrum region make it well-suited for a wide range of optoelectronic applications,[17, 18] offering opportunities for advancements in infrared imaging, communication, sensing, and energy harvesting technologies.

Despite its rocksalt crystal structure, ScN has been effectively combined with the wurtzite group-13 (or -IIIA) nitrides for various purposes. For instance, it serves as defect filtering in GaN,[19, 20] and it can be used as as a high-temperature ohmic contact owing to its low electrical resistivity.[21, 22] Additionally, ScN combined with GaN(0001) has been theoretically proposed for electronic applications, benefiting from their small lattice mismatch (Δa/a≈0.1%\Delta a/a \approx0.1\%) and a significant polarization discontinuity at the ScN(111)/GaN(0001) hetero-interface.[23] However, ScN is commonly reported as a degenerate semiconductor due to the presence of defects and impurities, limiting this application.[12, 13, 18, 21, 24, 25, 26, 27, 28, 29] Very recently, we have for the first time reported on nondegenerate ScN(111)/GaN(0001) layers with high carrier mobility.[22] Finally, ScN can also integrate with AlN to form wurtzite (Sc,Al)N ternary alloys for applications in surface-acoustic-wave devices,[30, 31, 32, 33] field-effect transistors,[34, 35, 36] and as novel ferroelectric material.[37, 38]

ScN layers with three different surface orientations have been previously studied, namely, ScN(001),[13, 24, 26, 29, 39, 40, 41, 42] ScN(110),[40, 43] and ScN(111).[11, 21, 22, 41, 44, 45] Exploring the growth of ScN on different substrates holds great promise for uncovering new surface orientations and properties. Such investigations can lead to the development of innovative material configurations with tailored properties, thereby potentially expanding the range of applications for ScN-based devices, particularly in catalyst applications.

In this study, we investigate the structural, optical and electrical properties of undoped ScN layers simultaneously grown on AlN(112ˉ\bar{2}2)/Al2_2O3_3(101ˉ\bar{1}0) and Alˉ\bar{\mathrm{Al}}N(0001)/Al2_2O3_3(0001) by plasma-assisted molecular beam epitaxy (PAMBE). X-ray diffractometry (XRD) and transmission electron microscopy (TEM) are used to determine their surface orientations and in-plane orientation-relationships. The vibrational and optical properties of the layers are investigated by Raman and photoluminescence (PL) spectroscopy, respectively. Finally, temperature-dependent Hall-effect measurements are used to elucidate their electrical properties and to shed light on the dominant scattering mechanisms.

Experimental

Intentionally undoped ScN layers are grown on semipolar AlN(112ˉ\bar{2}2) templates by PAMBE. These templates were prepared on Al2_2O3_3(101ˉ\bar{1}0) wafers by metal-organic vapor phase epitaxy (MOVPE).[46, 47] These templates show a typical undulated surface morphology along the [11ˉ001\bar{1}00]AlN_{\mathrm{AlN}} direction Figure 1(a), attributed to anisotropic diffusion of atoms along the two different in-plane directions. Before being loaded into the ultrahigh vacuum environment, the templates are cleaned in a mixture of H3_3PO4_4 and H2_2SO4_4 acids (1:3 ratio) to remove the surface oxide as well as surface contaminants, and then rinsed with de-ionized water and finally blown dry with a nitrogen gun. Prior to ScN growth, the templates were outgassed for two hours at 500 °C in a load-lock chamber attached to the MBE system. The MBE growth chamber is equipped with high-temperature effusion cells to provide 5N-pure Sc and 6N-pure Al metals. A Veeco UNI-Bulb radio-frequency plasma source is used for the supply of active nitrogen (N*). 6N-pure N2_2 gas is used as N precursor, which is further purified by a getter filter. The N* flux is calculated from the thickness of a GaN layer grown under Ga-rich conditions, and thus with a growth rate limited by the N* flux.[22, 36] Prior the ScN growth, a 20-nm-thick AlN buffer layer was grown at a thermocouple temperature of 1000 °C under slightly Al-rich conditions. Subsequently, the ScN layers are grown at the same temperature with thicknesses (dScNd_{\mathrm{ScN}}) ranging from 85 to 210 nm under N*-rich conditions. For comparison, ScN reference layers are grown simultaneously on polar AlN(0001) templates, which were prepared by MOVPE on Al2_2O3_3(0001) with a 4° miscut along the [112ˉ011\bar{2}0]AlN_{\mathrm{AlN}} direction.

Figure 1. 5×5 μm25 \times5\,\mu\mathrm{m}^{2} atomic force topographs of (top row) the ScN(113) layers simultaneously grown on AlN(112ˉ211\bar{2}2) templates and (bottom row) the ScN(111) layers on AlN(0001) templates with different thicknesses. The scale bar is 1 μm1\,\mu\mathrm{m}, while the zz scale is in units of nm. Values of the root-mean-square (rms) surface roughness obtained from these topographs are given in each topograph.

The structural properties of the layers are characterized using a high-resolution (HR)XRD system (Philips Panalytical X’Pert PRO MRD) equipped with a two-bounce hybrid monochromator Ge(220) for the CuKα1\alpha_{1} source (λ=1.540 598 A˚\lambda= 1.540\,598\,\text{\AA}). To further investigate the microstructural properties and details of the crystallographic arrangement at the hetero-interfaces, the 210-nm-thick ScN/AlN(112ˉ211\bar{2}2) layer is selected for (scanning) transmission electron microscopy (S)TEM measurements. TEM measurements are performed with a JEOL 2100F microscope operated at 200 kV and equipped with a brightfield (BF) detector, a high-angle annular dark-field (HAADF) detector and a Gatan Ultra Scan 4000 charge coupled device. Cross-sectional TEM specimens are prepared for observations along the orthogonal [1ˉ100]AlN[\bar{1}100]_{\mathrm{AlN}} and [11ˉ23]AlN[1\bar{1}23]_{\mathrm{AlN}} projections of the AlN(112ˉ211\bar{2}2) template using standard mechanical polishing and dimpling, followed by argon ion-milling. Analysis of high-resolution (HR)TEM phase-contrast micrographs and diffractograms is performed using Gatan Inc.’s Digital Micrograph™ (DM) software and JEMS simulation program.[48, 49]

The surface morphology of all the layers is imaged by atomic force microscopy in contact mode (Dimension Edge, Bruker). Raman and PL spectra of the layers are recorded at room temperature (RT) using a Horiba LabRAM HR Evolution™ Raman microscope. The samples are excited with a GaN-based diode laser (λex=405 nm\lambda_{\mathrm{ex}} = 405\,\mathrm{nm}) and a diode-pumped solid state laser (λex=473 nm\lambda_{\mathrm{ex}} = 473\,\mathrm{nm}) focused onto their surface for PL and Raman measurements, respectively. To investigate the electrical properties of the ScN layers, Hall-effect measurements are carried out in the van der Pauw configuration at 4–380 K. A magnetic field of 0.7 T is applied for these measurements.

Results and Discussion

Surface morphology

Figure 1 shows the surface morphology of the ScN layers simultaneously grown on AlN(112ˉ211\bar{2}2) and AlN(0001) templates. The ScN/AlN(112ˉ211\bar{2}2) and ScN/AlN(0001) layers duplicate the surface morphology of the templates with slightly larger root-mean-square roughness values, that increase from 3.5 to 4.2 nm and from 1.8 to 3.3 nm over a scanning area of 5×5 μm25 \times5\,\mu\mathrm{m}^{2} with increasing thickness, respectively. This increase in roughness with thickness is due to three-dimensional growth that can be clearly seen on the layers’ surfaces as particle-like formations, which we attribute to the N∗\mathrm{N}^{*}-rich conditions.

Structural properties

Phase purity and crystallinity

To investigate the epitaxial orientations of the layers grown on the two differently oriented AlN templates, symmetric 2θ−ω2\theta-\omega XRD survey scans has been performed over a wide angular range using an open detector. Figure 2 shows

Figure 2. Symmetric 2θ−ω2\theta-\omega XRD scans of 85-nm-thick ScN layers simultaneously grown on (a) AlN(112ˉ2)(11\bar{2}2)/Al2_2O3(101ˉ0)_3(10\bar{1}0) and (b) AlN(0001)(0001)/Al2_2O3(0001)_3(0001). Scans of the ScN/AlN(112ˉ2)(11\bar{2}2) layer were performed along two in-plane directions of AlN(112ˉ2)(11\bar{2}2). All these measurements were performed with an open detector without any receiving slit.

the XRD scans of the 85-nm-thick ScN layers (data of the 210-nm-thick layers are shown in Fig. S1 in supplementary material). Due to the two-fold symmetry of the AlN(112ˉ2)(11\bar{2}2) template, XRD measurements of the layers grown on this template were performed along the two primary in-plane directions of AlN(112ˉ2)(11\bar{2}2). The scan along the [11ˉ00]AlN[1\bar{1}00]_{\mathrm{AlN}} direction indicates two main reflections: Al2_2O3_3 303ˉ030\bar{3}0 and AlN 112ˉ211\bar{2}2, with an additional shoulder related to the Al2_2O3_3 reflection observed adjacent to the Al2_2O3_3 reflection. When scanning along the orthogonal [11ˉ23]AlN[1\bar{1}23]_{\mathrm{AlN}} direction, the Al2_2O3_3 3ˉ03ˉ0\bar{3}0\bar{3}0 reflection is not observed, while the ScN and AlN 112ˉ211\bar{2}2 reflections remain. This finding is explained by symmetric reciprocal space maps measured along these two directions, as shown in Figure 3. There is almost no tilt between the ScN, AlN and Al2_2O3_3 reflections along the [11ˉ00]AlN[1\bar{1}00]_{\mathrm{AlN}} direction, indicating that these surface planes are exactly parallel with respect to each other. A significant displacement of 2–2.8° has been observed between the reflections of AlN and ScN with respect to that of Al2_2O3_3 along the [11ˉ23]AlN[1\bar{1}23]_{\mathrm{AlN}} direction. This tilt is commonly observed for nonpolar and semipolar group-IIIA_{\mathrm{A}} nitrides grown on foreign substrates, and originates from the strain relaxation due to misfit dislocation at the hetero-interface.[46, 47, 50, 51, 52]

Figure 3. Reciprocal space maps of the 85-nm-thick ScN(113)(113) layer grown on AlN(112ˉ2)(11\bar{2}2) template measured along (a) the [11ˉ00]AlN[1\bar{1}00]_{\mathrm{AlN}} and (b) [11ˉ23]AlN[1\bar{1}23]_{\mathrm{AlN}} directions. These measurements were performed with open detector using a 1-mm-wide receiving slit. In (b), the broadening along the [0001]AlN[0001]_{\mathrm{AlN}} direction is due to basal-plane stacking faults.[46, 47] The diagonal line across the Al2_2O3_3 reflections are due to an instrumental artifact, namely, the detector streak (DS).

The ScN 113 reflection corresponds to a lattice parameter of 4.512 Å, which is identical to the value obtained for the reference layer (see Fig. S2 in supplementary material). Note that this lattice parameter is slightly larger than the reported value of 4.505 Å for strain-free ScN.[53] We attribute this increase to the high electron concentration in our layers (see their electrical properties below), leading to a lattice expansion due to the deformation potential interaction.[54, 55]

For the reference layers grown with different thicknesses on the AlN(0001) templates, ScN with pure (111) surface orientation is observed, as depicted in Figure 2(b) for the 85-nm-thick layer [data of the 210-nm-thick layer shown in Fig. S1(b) in supplementary material], similar to previous reports.[11, 18, 21, 22] The results obtained here suggest that under these identical growth conditions, both the ScN(111) and ScN(113) surfaces remain stable, with their appearances determined by the differing surface orientations of the templates. To the best of our knowledge, this is the first report ever on the growth of TMNs with (113) surface orientation.

To investigate the epitaxial orientation-relationship between ScN(113), AlN(112ˉ211\bar{2}2) and Al2_2O3_3(101ˉ010\bar{1}0), azimuthal scans and pole figures have been recorded, as depicted in Figure 4. These scans indicate the presence of twinning in ScN(113) with the following in-plane relationship: [11ˉ0]ScN∥[11ˉ23]AlN∥[0001]Al2O3[1\bar{1}0]_{\mathrm{ScN}} \parallel[1\bar{1}23]_{\mathrm{AlN}} \parallel[0001]_{\mathrm{Al_2O_3}} (opposite twinned direction: [1ˉ10]ScN∥[11ˉ23]AlN[\bar{1}10]_{\mathrm{ScN}} \parallel[1\bar{1}23]_{\mathrm{AlN}}) and [3ˉ32]ScN∥[11ˉ00]AlN∥[112ˉ0]Al2O3[\bar{3}32]_{\mathrm{ScN}} \parallel[1\bar{1}00]_{\mathrm{AlN}} \parallel[11\bar{2}0]_{\mathrm{Al_2O_3}}, as illustrated in Figure 4(c). For simplicity, we will denote the main in-plane direction of ScN as [11ˉ0]ScN[1\bar{1}0]_{\mathrm{ScN}}. Interestingly, a non-ideal angular spacing of ≈80°, rather than the expected 90°, between the ScN 002 and AlN 0002 reflections has been observed. This deviation from the ideal 90° is attributed to an in-plane lattice distortion, likely caused by residual strain and slight misorientations between twinned domains. For comparison, the ScN(111)/AlN(0001) reference layers exhibit two twin domains with the in-plane relationship [112ˉ]ScN∥[11ˉ00]AlN[11\bar{2}]_{\mathrm{ScN}} \parallel[1\bar{1}00]_{\mathrm{AlN}} and [11ˉ0]ScN[1\bar{1}0]_{\mathrm{ScN}}

Figure 4. (a) Azimuthal scans conducted on the 85-nm-thick ScN(113) layer of the Al2_2O3_3 {2024}\{2024\} (ψ=32.4∘\psi= 32.4^\circ), AlN {0002}\{0002\} (ψ=58.0∘\psi= 58.0^\circ) and ScN {002}\{002\} planes (ψ=25.2∘\psi= 25.2^\circ) performed in skew-symmetric configurations. Pole figures of (b) the AlN 0002 (2θ=36.0∘2\theta= 36.0^\circ, ω=18.0∘\omega= 18.0^\circ) and (c) ScN 002 reflections (2θ=40.0∘2\theta= 40.0^\circ, ω=20.0∘\omega= 20.0^\circ).

|| [1ˉ1ˉ20]AlN[\bar{1}\bar{1}20]_{\mathrm{AlN}} (see Fig. S3 in supplementary material).

Figure 5 shows ball-and-stick models of the atomic configuration of ScN(113)/AlN(112ˉ211\bar{2}2) created by VESTA.[56] Since the surface normal of the (112ˉ211\bar{2}2) plane cannot be reduced to integer Miller or Miller–Bravais indices, we denote it here by SAlN(112ˉ2)S_{\mathrm{AlN}(11\bar{2}2)}. Note that the angle between the [112ˉ2]AlN[11\bar{2}2]_{\mathrm{AlN}} direction and SAlN(112ˉ2)S_{\mathrm{AlN}(11\bar{2}2)} is 14.9∘14.9^\circ, i. e., the former should not be mistaken for the surface normal. The cross-sectional view shown in Figure 5(a) indicates that the surface is stepped with {001}\{001\} terraces and {111}\{111\} risers, which are inclined with respect to the singular {113}\{113\} surfaces by angles of 25.2∘25.2^\circ and 29.5∘29.5^\circ, respectively.

Figure 5. Side views of the atomic structures of ScN(113)/AlN(112ˉ211\bar{2}2): (a) along the [3ˉ32]ScN[\bar{3}32]_{\mathrm{ScN}} and [1ˉ100]AlN[\bar{1}100]_{\mathrm{AlN}} zone axes, and (b) along the [1ˉ10]ScN[\bar{1}10]_{\mathrm{ScN}} and [11ˉ23]AlN[1\bar{1}23]_{\mathrm{AlN}} zone axes. SAlN(112ˉ2)S_{\mathrm{AlN}(11\bar{2}2)} denotes the surface normal of the AlN(112ˉ211\bar{2}2) plane. (c) Top view of the ScN(113) on AlN(112ˉ211\bar{2}2) atomic structures. Rectangular shapes indicate the 1×21 \times2 unit cells of ScN(113) and 2×12 \times1 unit cells of AlN(112ˉ211\bar{2}2). In (c), note the different colors of N atoms on the ScN topmost and AlN underneath surfaces.

As depicted in Figure 5(c), a 1×21 \times2 super cell of ScN(113) matches a 2×12 \times1 super cell of AlN(112ˉ211\bar{2}2), resulting in a near coincidence site lattice with a residual lattice mismatch (fScN/AlNf_{\mathrm{ScN/AlN}}) of −1.8%-1.8\% and 8.6%8.6\% along the [3ˉ32]ScN∥[1ˉ100]AlN[\bar{3}32]_{\mathrm{ScN}} \parallel[\bar{1}100]_{\mathrm{AlN}} direction and [1ˉ10]ScN∥[11ˉ23]AlN[\bar{1}10]_{\mathrm{ScN}} \parallel[1\bar{1}23]_{\mathrm{AlN}} direction, respectively. Here, the fScN/AlNf_{\mathrm{ScN/AlN}} values were calculated using the lattice parameter of 4.5124.512 Å measured for the ScN layers in this study and the relaxed lattice parameters a=3.112a = 3.112 Å and c=4.981c = 4.981 Å reported for AlN.[57, 58]

X-ray rocking curve measurements were conducted to assess the crystallinity of the layers. The 85-nm-thick ScN(113) layer exhibits a slight anisotropy in ScN 113 rocking curves measured along two in-plane directions: the values of the full-width at half maximum (FWHM) amount to 1.5∘1.5^\circ and 1.8∘1.8^\circ along the [3ˉ32]ScN[\bar{3}32]_{\mathrm{ScN}} and [1ˉ10]ScN[\bar{1}10]_{\mathrm{ScN}} directions, respectively. This is analogous to the AlN(112ˉ211\bar{2}2) templates, where FWHM values of 0.3∘0.3^\circ and 0.5∘0.5^\circ are obtained in the AlN 112ˉ211\bar{2}2 rocking curves along the [11ˉ23]AlN[1\bar{1}23]_{\mathrm{AlN}} and [1ˉ100]AlN[\bar{1}100]_{\mathrm{AlN}} directions, respectively. An anisotropic broadening of the ScN 113 reflection is also observed in the reciprocal space maps (Figure 3). In the case of the 85-nm-thick ScN(111) reference layer, the FWHM of the ScN 111 rocking curve is 0.3∘0.3^\circ, which represents one of the best values reported in the literature.[12, 42] The higher crystallinity of the ScN(111) layer is attributed mainly to the higher quality of the AlN(0001) templates, i. e., a smoother surface morphology [Figure 1(d)] and higher crystallinity (FWHM values of the AlN 0002 and AlN 101ˉ310\bar{1}3 rocking curves are 0.02∘0.02^\circ and 0.07∘0.07^\circ, respectively). Interestingly, the FWHM values of the 210-nm-thick layers are not improved compared to those of the 85-nm-thick layers. This can be explained by the insufficient lateral growth under N∗^*-rich conditions, which results in a columnar growth structure and impedes a progressive improvement in crystallinity with increasing thickness.

Microstructural properties

Overview BF-STEM images of the 210-nm-thick ScN/AlN(112‾\overline{2}2) layer shown in Figure 6(a) and 6(c) reveal a ScN layer composed of coalesced columnar grains with an average diameter of about 20–50 nm. The grains have a single orientation, (113), and well-defined epitaxial relationships as will be discussed below. The basal-plane stacking faults (BSFs) in the AlN(112‾\overline{2}2) layer are terminated at the ScN/AlN interface [Figure 6(a)], which is due to the transition from the wurtzite crystal structure of AlN to the rocksalt crystal structure of ScN. In the wurtzite structure of AlN, BSFs are defined as deviations from the ABAB... stacking sequence of the (0001) basal planes normal to the [1]AlN_{\mathrm{AlN}} direction.[52] This stacking sequence cannot propagate into the rocksalt ScN layer, which exhibits the characteristic cubic ABCABC... stacking sequence of its (111) planes normal to the [111]ScN_{\mathrm{ScN}} direction.[59] The distinct crystallographic configurations of the wurtzite and rocksalt structures inherently inhibit the continuation of BSFs into ScN, as the rocksalt structure does not accommodate the specific planar defects found in the wurtzite structure. Consequently, this difference in crystal structure results in the natural termination of these faults at the interface between the two materials.

BF-STEM and HRTEM images of ScN/AlN

Figure 6. (a) Overview BF-STEM and (b) HRTEM images of the 210-nm-thick ScN(113) layer grown on the AlN(112‾\overline{2}2) template taken along the [11‾\overline{1}00]AlN_{\mathrm{AlN}} zone axis. The inclined dark lines in the AlN area are BSFs. The square shapes in (b) indicate the areas from where the FFT patterns on (b1) AlN, (b2) ScN/AlN, and (b3) ScN were captured. (c) Overview BF-STEM and (d) HRTEM images taken along the [11‾\overline{1}23]AlN_{\mathrm{AlN}} zone axis. (d1) and (d2) are FFT patterns from the two selected areas in (d). Arrows in (d) indicate twin boundaries.

Figures 6(b) and 6(d) display representative HRTEM phase-contrast micrographs of the ScN/AlN interface acquired along the [1ˉ100]AlN[\bar{1}100]_{\mathrm{AlN}} and [1ˉ1ˉ23]AlN[\bar{1}\bar{1}23]_{\mathrm{AlN}} zone axes, respectively. Though the TEM images evidence the local presence of surface undulations at the ScN/AlN interface, there is no noticeable misalignment of the ScN(113) layer which grows epitaxially on AlN(112ˉ2)(11\bar{2}2). HRTEM investigations confirm the epitaxial relationship [1ˉ10]ScN∥[1ˉ1ˉ23]AlN[\bar{1}10]_{\mathrm{ScN}} \parallel[\bar{1}\bar{1}23]_{\mathrm{AlN}} and [3ˉ32]ScN∥[1ˉ100]AlN[\bar{3}32]_{\mathrm{ScN}} \parallel[\bar{1}100]_{\mathrm{AlN}} in good agreement with XRD data. This epitaxial orientation-relationship has been determined after comparison of the experimental data with simulated diffraction patterns obtained using the JEMS simulation suite.[48, 49]

Interestingly, the TEM results also reveal the presence of an additional in-plane relationship between ScN(113) and AlN(112ˉ2)(11\bar{2}2), which is [1ˉ21]ScN∥[1ˉ100]AlN[\bar{1}21]_{\mathrm{ScN}} \parallel[\bar{1}100]_{\mathrm{AlN}} and [74ˉ1]ScN∥[1ˉ1ˉ23]AlN[7\bar{4}1]_{\mathrm{ScN}} \parallel[\bar{1}\bar{1}23]_{\mathrm{AlN}} (see Figs. S4–S5 in the supplementary material). This relationship becomes very noticeable when the layer is observed along the [1ˉ100]AlN[\bar{1}100]_{\mathrm{AlN}} zone axis (see Fig. S5 in the supplementary material). The additional relationship, however, has not been observed in the azimuthal and pole figure XRD measurements (Figure 4). It is noteworthy that HRTEM measurements were performed on much smaller areas, typically in the nanometer range, compared to those of XRD measurements, which typically cover much larger areas (here ≈ 0.4×12 mm20.4 \times12\ \mathrm{mm}^{2}). Hence, we conclude that the layer was predominantly grown with the first in-plane relationship.

Fast Fourier Transform (FFT) patterns captured on different areas on the HRTEM micrographs [Figure 6(b) and Figure 6(d)] indicate that, regardless of the in-plane relationship, the ScN layer exhibits a (113) surface orientation, consistent with XRD data. The high density of rotational twins in the ScN(113) layer is also visible in the overall surface morphology, which is characterized by mirror-symmetric {001} and {111} facets [Figure 6(a) and Figure 6(c)]. While both of these planes are present already on the bulk-terminated (113) surface [see Figure 5(a)], their development into well-defined facets reflects the fact that they represent the crystal planes with the lowest surface energy in the rocksalt structure.[60]

Figure 6(d) shows FFT patterns captured on different areas on the HRTEM micrograph taken along the [1ˉ1ˉ23]AlN[\bar{1}\bar{1}23]_{\mathrm{AlN}} zone axis and [1ˉ10]ScN[\bar{1}10]_{\mathrm{ScN}} zone axis, and following the epitaxial relationship [3ˉ32]ScN∥[1ˉ100]AlN[\bar{3}32]_{\mathrm{ScN}} \parallel[\bar{1}100]_{\mathrm{AlN}} and [1ˉ10]ScN∥[1ˉ1ˉ23]AlN[\bar{1}10]_{\mathrm{ScN}} \parallel[\bar{1}\bar{1}23]_{\mathrm{AlN}}. In particular, FFT patterns of the selected regions marked in Figure 6(dFigure 1–Figure 6(dFigure 2 highlight the local presence of twins, with the twinning already visible in the HRTEM micrograph itself. Additionally, the lattice parameter of the ScN layer, as determined from diffractograms generated using micrographs taken along the [1ˉ10]ScN∥[1ˉ1ˉ23]AlN[\bar{1}10]_{\mathrm{ScN}} \parallel[\bar{1}\bar{1}23]_{\mathrm{AlN}} zone axis, is 4.514 Å, which is very close to the value deduced using XRD.

On the other hand, diffractograms from HRTEM images along the [1ˉ100]AlN[\bar{1}100]_{\mathrm{AlN}} zone axis reveal an apparent near-perfect epitaxial alignment of the ScN and AlN lattices for grains with the epitaxial relationship [1ˉ21]ScN∥[1ˉ100]AlN[\bar{1}21]_{\mathrm{ScN}} \parallel[\bar{1}100]_{\mathrm{AlN}} and [74ˉ1]ScN∥[1ˉ1ˉ23]AlN[7\bar{4}1]_{\mathrm{ScN}} \parallel[\bar{1}\bar{1}23]_{\mathrm{AlN}}, as reflected in the FFT pattern in Figure 6(bFigure 2 and in simulated diffraction patterns. Grains grown with this epitaxial relationship—[1ˉ21]ScN∥[1ˉ100]AlN[\bar{1}21]_{\mathrm{ScN}} \parallel[\bar{1}100]_{\mathrm{AlN}} and [74ˉ1]ScN∥[1ˉ1ˉ23]AlN[7\bar{4}1]_{\mathrm{ScN}} \parallel[\bar{1}\bar{1}23]_{\mathrm{AlN}}—are under biaxial compression along the [1ˉ100]AlN[\bar{1}100]_{\mathrm{AlN}} and [1ˉ1ˉ23]AlN[\bar{1}\bar{1}23]_{\mathrm{AlN}} directions, with fScN/AlN=2.5f_{\mathrm{ScN/AlN}} = 2.5 and 4.0%4.0\%, respectively (see atomic structures in Fig. S6 in the supplementary material).

The in-plane lattice mismatch of this secondary epitaxial alignment is lower than that of the primary epitaxial relationship, having a residual lattice mismatch of approximately −1.8%-1.8\% and 8.6%8.6\% along the [3ˉ32]ScN[\bar{3}32]_{\mathrm{ScN}} and [1ˉ10]ScN[\bar{1}10]_{\mathrm{ScN}} directions, respectively. At the first glance, it thus may seem that the secondary alignment should be energetically preferred. However, the elastic strain energy U∝CijϵiϵjU \propto C_{ij}\epsilon_i\epsilon_j[61] contains not only the normal components of the strain, but also the shear components, which we expect to be nonzero for the interface between AlN(112ˉ2)(11\bar{2}2) and ScN(113). In addition, additional factors beyond the elastic strain energy contribute to the epitaxial stabilization. These may include interfacial chemical bonding and atomic registry minimizing interface energy, anisotropic elastic properties, partial strain relaxation via dislocations, kinetic growth effects favoring certain nucleation pathways, and surface energy contributions.[62, 63, 64] Cumulatively, these effects can stabilize an epitaxial configuration that is not at the absolute minimum in elastic strain energy.

Vibrational and optical properties

The vibrational properties of ScN are particularly interesting due to its rocksalt structure, for which first-order Raman scattering is principally forbidden and only second-order processes are allowed. However, first-order modes are invariably observed experimentally, which is commonly attributed to a relaxation of the kk-selection rule due to the presence of lattice disorder arising from both point defects (such as vacancies and substitutional impurities) and structural defects.[65, 66] In this case, the Raman spectra basically reflects the phonon density of states (DOS), rather than consisting of only zone-center phonon modes.

Figure 7(a) shows that the Raman spectra of the 85-nm-thick ScN(113) and ScN(111) layers are almost identical. Two first-order phonon modes are observed: the transverse optical (TO) mode at the Γ\Gamma point [i.e., TO(Γ\Gamma) at 372 cm−1^{-1}] and the longitudinal optical (LO) mode at the LL point [i.e., LO(LL) at 680 ±\pm 1 cm−1^{-1}] in the phonon band structure of ScN. These assignments are consistent with previous results obtained on bulk ScN crystals,[67] ScN(001) layers,[17] and ScN(111) layers,[18, 22, 45] as well as with theoretical predictions.[68, 69] As shown previously for ScN(111)/Al2_2O3_3(0001)[18] and ScN(111)/GaN(0001)[22] the spectral position of the LO(LL) mode remains unchanged with varying layer thickness, indicating that the layers investigated here are also essentially fully relaxed due to the large lattice mismatch with AlN.

Figure 7. (a) Room-temperature Raman and (b) PL spectra of the 85-nm-thick ScN(113) and ScN(111) reference layers.

In this context, the observed LO(LL) mode arises from a high phonon DOS near the LL point of the Brillouin zone, where the LO phonon branch is relatively flat.[69, 70] Recently, an alternative interpretation has emerged for the rocksalt transition metal nitrides GdN and LuN.[71] The authors propose that the observed LO mode is due to LO(Γ\Gamma) scattering induced by the Fröhlich interaction, bypassing the selection rules for deformation-potential scattering. Grümbel et al.[72] have interpreted the spectrum of bulklike ScN layers with exceptionally low electron density along the same lines. However, their Raman spectrum also exhibits the TO(XX) mode, which can only be activated by lattice disorder. Unfortunately, there is no consensus on the exact energy dispersion of the LO mode, and in particular on the ordering of the LO(Γ\Gamma) and LO(LL) modes, which has been shown to sensitively depend on the computational approach chosen.[73] At present, it thus seems that the DOS-based interpretation provides a more consistent explanation of the spectral position and intensity of this feature in ScN, particularly for the thin layers with high defect density as considered in the present work.

Figure 7(b) shows an example of the PL spectra of the 85-nm-thick ScN(113) and ScN(111) layers under investigation. These layers exhibit similar PL characteristics, with a broad band centered at (2.16±0.01) eV(2.16 \pm0.01)\ \mathrm{eV} and an FWHM of about 0.2 eV0.2\ \mathrm{eV}. This peak emission aligns with the lowest direct band gap at the XX point of the ScN electronic band structure, consistent with previous findings.[16, 18, 24, 25, 27, 40, 45]

Electrical properties

The electrical properties of the ScN(113) and ScN(111) layers were investigated using temperature-dependent Hall-effect measurements (4–380 K)(4\text{--}380\ \mathrm{K}) in the van der Pauw configuration. To ensure reliable data, we focused on 85-nm-thick layers to minimize the influence of surface morphology. The ScN(113) layer exhibits a high electron density nn (nRT=3.7×1020 cm−3n_{\mathrm{RT}} = 3.7 \times10^{20}\ \mathrm{cm}^{-3}) with moderate electron mobility μ\mu (μRT=30 cm2V−1s−1\mu_{\mathrm{RT}} = 30\ \mathrm{cm}^{2}\mathrm{V}^{-1}\mathrm{s}^{-1}). In comparison, the ScN(111) reference layer shows a slightly lower nn (nRT=1.1×1020 cm−3n_{\mathrm{RT}} = 1.1 \times10^{20}\ \mathrm{cm}^{-3}) but higher μ\mu (μRT=78 cm2V−1s−1\mu_{\mathrm{RT}} = 78\ \mathrm{cm}^{2}\mathrm{V}^{-1}\mathrm{s}^{-1}). This higher μ\mu is attributed to the higher crystallinity of the ScN(111) layer. The very high conductivity of these layers (1−2×105 S/m)(1 - 2 \times10^{5}\ \mathrm{S}/\mathrm{m}) highlight their potential as material for thermoelectric devices.[11, 12, 13, 74]

For both layers, nn remains almost constant with temperature, with a minimum at about 250 K, while μ\mu is constant at low temperature and then decreases with increasing temperature. The constant values of nn and μ\mu up to a certain temperature means that the layers exhibit metallic behavior, similar to previous findings reported in the literature.[21, 22, 28, 29] The entry into a semiconducting behavior at higher temperature has been observed in many semiconductors and is indicative of a gradual change from transport in an impurity- and in the conduction band at low and high temperatures, respectively.[22]

The decrease in μ\mu with increasing temper-

ature has been previously reported by several groups[13, 16, 24, 28, 29, 75] and has been qualitatively attributed to dislocation,[13] acoustic phonon[24, 75] or optical phonon scattering.[28, 29] Recently, through a quantitative analysis of the temperature-dependent μ\mu of ScN(111) layers grown on semi-insulating GaN(0001),[22] we found that at elevated temperatures, μ\mu in these layers is primarily constrained by optical phonon scattering. This observation is consistent with recent theoretical calculations, which indicate that optical phonon scattering tends to dominate over acoustic phonon scattering in ScN.[76] By using the same approach, we also fit the measured μ(T)\mu(T) of the samples studied here using.[22]

μ(T)=[A(eEph/kBT+1)−1+BT−γ]−1(1)\mu(T)=\left[A\left(e^{E_{\mathrm{ph}}/k_{\mathrm{B}}T}+1\right)^{-1}+BT^{-\gamma}\right]^{-1} \tag*{(1)}

where EphE_{\mathrm{ph}} is the effective phonon energy,[77] AA and BB are constants, kBk_{\mathrm{B}} is the Boltzmann constant, and the exponent γ\gamma represents contributions from various other scattering mechanisms including, in particular, charged point and line defects. Fit of the experimental data Figure 8(b), return a value for γ\gamma close to zero because of the metallic impurity-band conduction. The fits yield comparable EphE_{\mathrm{ph}} values of 56 meV for the ScN(113) layer and 62 meV for the ScN(111) layer. These values fall within the range of phonon energies typically observed for TO(Γ\Gamma) (≈46\approx46 meV) and LO(LL) (≈84\approx84 meV) phonon modes in ScN [see Raman spectra in Figure 7(a)], consistent with our previously reported value.[22] This results suggest a strong electron-optical-phonon interaction as predicted theoretically for the highly ionic semiconductor ScN.[76, 78]

Figure 8. Temperature-dependent (a) electron concentration nn and (b) mobility μ\mu of the 85-nm-thick ScN(113) and ScN(111) reference layers. Lines in (a) are guides to the eye, while lines in (b) represent the fits to the data using Eq. (1).

Summary

To summarize and conclude, we have reported for the first time on the growth and characterization of the ScN(113) layers grown on AlN(112‾211\overline{2}2) templates using plasma-assisted molecular beam epitaxy. Two distinct in-plane relationships were identified: the major [11‾0]ScN∥[1‾123]AlN[1\overline{1}0]_{\mathrm{ScN}} \mathbin{\|} [\overline{1}123]_{\mathrm{AlN}} and [332‾]ScN∥[11‾00]AlN[33\overline{2}]_{\mathrm{ScN}} \mathbin{\|} [1\overline{1}00]_{\mathrm{AlN}}, which is under anisotropic tensile-compressive strain, and the minor [12‾1]ScN∥[11‾00]AlN[1\overline{2}1]_{\mathrm{ScN}} \mathbin{\|} [1\overline{1}00]_{\mathrm{AlN}} and [74‾1‾]ScN∥[1‾123]AlN[7\overline{4}\overline{1}]_{\mathrm{ScN}} \mathbin{\|} [\overline{1}123]_{\mathrm{AlN}}, which is under anisotropic biaxial compression. Room-temperature photoluminescence measurements reveal a broad luminescence band with a peak emission energy of ≈2.16\approx2.16 eV, corresponding to the lowest direct band gap at the XX point of the ScN electronic band structure. Temperature-dependent Hall-effect measurements indicate highly degenerate layers at low temperature, with transport dominated by impurity band conduction. Optical phonon scattering, with an effective phonon energy of (60 ±\pm 3) meV, limits carrier transport at high temperature.

Acknowledgement

We thank Carsten Stemmler for expert technical assistance with the MBE system and Doreen Steffen for TEM sample preparation. The authors are grateful to Manfred Ramsteiner for enlightening discussions and Michael Hanke for a critical reading of the manuscript. We also thank Markus Pristovsek at Nagoya University for supplying AlN templates.

Supporting Information Available

See supplementary material for (1) symmetric 2θ−ω2\theta-\omega XRD scans of 210-nm-thick ScN layers simultaneously grown on AlN(112‾211\overline{2}2) and AlN(0001) templates; (2) symmetric 2θ−ω2\theta-\omega XRD scan and thickness simulation of the 85-nm-thick ScN(111) reference layer grown on AlN(0001) template; (3) azimuthal and pole figure scans of the 85-nm-thick ScN(111) reference layer; (4) HRTEM image of the 210-nm-thick ScN(113) grown on AlN(112‾211\overline{2}2) template taken along the [74‾1‾]ScN[7\overline{4}\overline{1}]_{\mathrm{ScN}} and [1‾123]AlN[\overline{1}123]_{\mathrm{AlN}} zone axes; (5) HRTEM image of the 210-nm-thick ScN(113) grown on AlN(112‾211\overline{2}2) template taken along the [332‾]ScN[33\overline{2}]_{\mathrm{ScN}} and [11‾00]AlN[1\overline{1}00]_{\mathrm{AlN}} zone axes; (6) Side views of the atomic structures of ScN(113) on AlN(112‾211\overline{2}2) with the in-plane relationship [1‾21]ScN∥[1‾00]AlN[\overline{1}21]_{\mathrm{ScN}} \mathbin{\|} [\overline{1}00]_{\mathrm{AlN}} and [74‾1‾]ScN∥[1‾123]AlN[7\overline{4}\overline{1}]_{\mathrm{ScN}} \mathbin{\|} [\overline{1}123]_{\mathrm{AlN}}.

References

  1. [1]Eklund, P.; Kerdsongpanya, S.; Alling, B. Transition-metal-nitride-based thin films as novel energy harvesting materials. J. Mater. Chem. C 2016, 4, 3905.
  2. [2]Abghoui, Y.; Skúlason, E. Hydrogen evolution reaction catalyzed by transition-metal nitrides. J. Phys. Chem. C 2017, 121, 24036.
  3. [3]Biswas, B.; Saha, B. Development of semi-conducting ScN. Phys. Rev. Mater. 2019, 3, 020301.
  4. [4]Ologunagba, D.; Kattel, S. Pt- and Pd-modified transition metal nitride catalysts for the hydrogen evolution reaction. Phys. Chem. Chem. Phys. 2022, 24, 12149.DOI
  5. [5]Mahadik, S.; Surendran, S.; Kim, J. Y.; Janani, G.; Lee, D.-K.; Kim, T.-H.; Kim, J. K.; Sim, U. Syntheses and electronic structure engineering of transition metal nitrides for supercapacitor applications. J. Mater. Chem. A 2022, 10, 14655.DOI
  6. [6]Meng, Z.; Zheng, S.; Luo, R.; Tang, H.; Wang, R.; Zhang, R.; Tian, T.; Tang, H. Transition metal nitrides for electrocatalytic application: progress and rational design. Nanomaterials 2022, 12, 2660.DOI
  7. [7]Gall, D.; Petrov, I.; Hellgren, N.; Hultman, L.; Sundgren, J. E.; Greene, J. E. Growth of poly- and single-crystal ScN on MgO (001): Role of low-energy N₂⁺ irradiation in determining texture, microstructure evolution, and mechanical properties. J. Appl. Phys. 1998, 84, 6034.DOI
  8. [8]Gschneidner, K. A., Jr. Rare earth alloys: a critical review of the alloy systems of the rare earth, scandium, and yttrium metals; D. Van Nostrand Company, Ltd.: London, 1961.
  9. [9]Rawat, V.; Koh, Y. K.; Cahill, D. G.; Sands, T. D. Thermal conductivity of (Zr,W)N/ScN metal/semiconductor multilayers and superlattices. J. Appl. Phys. 2009, 105, 024909.DOI
  10. [10]Garbrecht, M.; Schroeder, J. L.; Hultman, L.; Birch, J.; Saha, B.; Sands, T. D. Microstructural evolution and thermal stability of HfN/ScN, ZrN/ScN, and Hf₀.₅Zr₀.₅N/ScN metal/semiconductor superlattices. J. Mater. Sci. 2016, 51, 8250.DOI
  11. [11]Kerdsongpanya, S.; Van Nong, N.; Pryds, N.; Žukauskaitė, A.; Jensen, J.; Birch, J.; Lu, J.; Hultman, L.; Wingqvist, G.; Eklund, P. Anomalously high thermoelectric power factor in epitaxial ScN thin films. Appl. Phys. Lett. 2011, 99, 321113.DOI
  12. [12]Burmistrova, P. V.; Maassen, J.; Favaloro, T.; Saha, B.; Salamat, S.; Rui Koh, Y.; Lundstrom, M. S.; Shakouri, A.; Sands, T. D. Thermoelectric properties of epitaxial ScN films deposited by reactive magnetron sputtering onto MgO(001) substrates. J. Appl. Phys. 2013, 113, 153704.DOI
  13. [13]Rao, D.; Biswas, B.; Flores, E.; Chatterjee, A.; Garbrecht, M.; Koh, Y. R.; Bhatia, V.; Pillai, A. I. K.; Hopkins, P. E.; Martin-Gonzalez, M.; Saha, B. High mobility and high thermoelectric power factor in epitaxial ScN thin films deposited with plasma-assisted molecular beam epitaxy. Appl. Phys. Lett. 2020, 116, 152103.DOI
  14. [14]Al-Brithen, H. A.; Yang, H.; Smith, A. R. Incorporation of manganese into semiconducting ScN using radio frequency molecular beam epitaxy. J. Appl. Phys. 2004, 96, 3787.DOI
  15. [15]Herwadkar, A.; Lambrecht, W. R. L. Mn-doped ScN: A dilute ferromagnetic semiconductor with local exchange coupling. Phys. Rev. B 2005, 72, 235207.DOI
  16. [16]Saha, B.; Naik, G.; Drachev, V. P.; Boltasseva, A.; Marinero, E. E.; Sands, T. D. Electronic and optical properties of ScN and (Sc,Mn)N thin films deposited by reactive DC-magnetron sputtering. J. Appl. Phys. 2013, 114, 063519.
  17. [17]Maurya, K. C.; Rao, D.; Acharya, S.; Rao, P.; Pillai, A. I. K.; Selvaraja, S. K.; Garbrecht, M.; Saha, B. Polar semiconducting scandium nitride as an infrared plasmon and phonon–polaritonic material. Nano Lett. 2022, 22, 5182.DOI
  18. [18]Dinh, D. V.; Peiris, F.; Lähnemann, J.; Brandt, O. Optical properties of ScN lay- ers grown on Al₂O₃(0001) by plasma-assisted molecular beam epitaxy. Appl. Phys. Lett. 2023, 123, 112102.
  19. [19]Moram, M. A.; Zhang, Y.; Kappers, M. J.; Barber, Z. H.; Humphreys, C. J. Dislocation reduction in gallium nitride films using scandium nitride interlayers. Appl. Phys. Lett. 2007, 91, 152101.DOI
  20. [20]Johnston, C. F.; Moram, M. A.; Kappers, M. J.; Humphreys, C. J. Defect reduction in (11̄22) semipolar GaN grown on m-plane sapphire using ScN interlayers. Appl. Phys. Lett. 2009, 94, 161109.
  21. [21]Casamento, J.; Wright, J.; Chaudhuri, R.; Xing, H. G.; Jena, D. Molecular beam epitaxial growth of scandium nitride on hexagonal SiC, GaN, and AlN. Appl. Phys. Lett. 2019, 115, 172101.DOI
  22. [22]Dinh, D. V.; Brandt, O. Electrical properties of ScN(111) layers grown on semi-insulating GaN(0001) by plasma-assisted molecular beam epitaxy. Phys. Rev. Appl. 2024, 22, 014067.DOI
  23. [23]Adamski, N. L.; Dreyer, C. E.; Van de Walle, C. G. Giant polarization charge density at lattice-matched GaN/ScN interfaces. Appl. Phys. Lett. 2019, 115, 232103.DOI
  24. [24]Dismukes, J. P.; Yim, W. M.; Ban, V. S. Epitaxial growth and properties of semiconducting ScN. J. Cryst. Growth 1972, 13, 365.
  25. [25]Moram, M. A.; Barber, Z. H.; Humphreys, C. J. The effect of oxygen incorporation in sputtered scandium nitride films. Thin Solid Films 2008, 516, 8569.DOI
  26. [26]Ohgaki, T.; Watanabe, K.; Adachi, Y.; Sakaguchi, I.; Hishita, S.; Ohashi, N.; Haneda, H. Electrical properties of scandium nitride epitaxial films grown on (100) magnesium oxide substrates by molecular beam epitaxy. J. Appl. Phys. 2013, 114, 093704.DOI
  27. [27]Deng, R.; Ozsdolay, B. D.; Zheng, P. Y.; Khare, S. V.; Gall, D. Optical and transport measurement and first-principles determination of the ScN band gap. Phys. Rev. B 2015, 91, 045104.DOI
  28. [28]Cetnar, J. S.; Reed, A. N.; Badescu, S. C.; Vangala, S.; Smith, H. A.; Look, D. C. Electronic transport in degenerate (100) scandium nitride thin films on magnesium oxide substrates. Appl. Phys. Lett. 2018, 113, 192104.DOI
  29. [29]Al-Atabi, H.; Zheng, Q.; Cetnar, J. S.; Look, D.; Cahill, D. G.; Edgar, J. H. Properties of bulk scandium nitride crystals grown by physical vapor transport. Appl. Phys. Lett. 2020, 116, 132103.DOI
  30. [30]Akiyama, M.; Kamohara, T.; Kano, K.; Teshigahara, A.; Takeuchi, Y.; Kawahara, N. Enhancement of piezoelectric response in scandium aluminum nitride alloy thin films prepared by dual reactive cosputtering. Adv. Mater. 2009, 21, 593.DOI
  31. [31]Tasnádi, F.; Alling, B.; Höglund, C.; Wingqvist, G.; Birch, J.; Hultman, L.; Abrikosov, I. A. Origin of the anomalous piezoelectric response in wurtzite ScₓAl₁₋ₓN alloys. Phys. Rev. Lett. 2010, 104, 137601.
  32. [32]Hashimoto, K.-y.; Sato, S.; Teshigahara, A.; Nakamura, T.; Kano, K. High-performance surface acoustic wave resonators in the 1 to 3 GHz range using a ScAlN/6H-SiC structure. IEEE Trans. Ultrason. Ferroelectr. Freq. Control 2013, 60, 637.DOI
  33. [33]Yuan, M.; Dinh, D. V.; Mandal, S.; Williams, O. A.; Chen, Z.; Brandt, O.; Santos, P. V. Generation of GHz surface acoustic waves in (Sc,Al)N thin films grown on free-standing polycrystalline diamond wafers by plasma-assisted molecular beam epitaxy. J. Phys. D: Appl. Phys. 2024, 57, 495103.DOI
  34. [34]Hardy, M. T.; Downey, B. P.; Nepal, N.; Storm, D. F.; Katzer, D. S.; Meyer, D. J. Epitaxial ScAlN grown by molecular beam epitaxy on GaN and SiC substrates. Appl. Phys. Lett. 2017, 110, 162104.
  35. [35]Wang, P.; Wang, D.; Wang, B.; Mohanty, S.; Diez, S.; Wu, Y.; Sun, Y.; Ahmadi, E.; Mi, Z. N-polar ScAlN and HEMTs grown by molecular beam epitaxy. Appl. Phys. Lett. 2021, 119, 082101.
  36. [36]Dinh, D. V.; Lähnemann, J.; Geelhaar, L.; Brandt, O. Lattice parameters of ScₓAl₁₋ₓN layers grown on GaN(0001) by plasma-assisted molecular beam epitaxy. Appl. Phys. Lett. 2023, 122, 152103.DOI
  37. [37]Fichtner, S.; Wolff, N.; Lofink, F.; Kienle, L.; Wagner, B. AlScN: A III-V semiconductor based ferroelectric. J. Appl. Phys. 2019, 125, 114103.DOI
  38. [38]Wang, P.; Wang, D.; Mondal, S.; Mi, Z. Ferroelectric N-polar ScAlN/GaN heterostructures grown by molecular beam epitaxy. Appl. Phys. Lett. 2022, 121, 023501.DOI
  39. [39]Gall, D.; Petrov, I.; Desjardins, P.; Greene, J. E. Microstructural evolution and Poisson ratio of epitaxial ScN grown on TiN(001)/MgO(001) by ultrahigh vacuum reactive magnetron sputter deposition. J. Appl. Phys. 1999, 86, 5524.DOI
  40. [40]Oshima, Y.; Villora, E. G.; Shimamura, K. Hydride vapor phase epitaxy and characterization of high-quality ScN epilayers. J. Appl. Phys. 2014, 115, 153508.DOI
  41. [41]le Febvrier, A.; Tureson, N.; Stilkerich, N.; Greczynski, G.; Eklund, P. Effect of impurities on morphology, growth mode, and thermoelectric properties of (111) and (001) epitaxial-like ScN films. J. Phys. D: Appl. Phys. 2018, 52, 035302.
  42. [42]Moram, M. A.; Novikov, S. V.; Kent, A. J.; Nörenberg, C.; Foxon, C. T.; Humphreys, C. J. Growth of epitaxial thin films of scandium nitride on 100-oriented silicon. J. Cryst. Growth 2008, 310, 2746.DOI
  43. [43]John, P.; Trampert, A.; Dinh, D. V.; Spallek, D.; Lähnemann, J.; Kaganer, V. M.; Geelhaar, L.; Brandt, O.; Auzelle, T. ScN/GaN(1̄100): A new platform for the epitaxy of twin-free metal-semiconductor heterostructures. Nano Lett. 2024, 24, 6233.
  44. [44]Acharya, S.; Chatterjee, A.; Bhatia, V.; Pillai, A. I. K.; Garbrecht, M.; Saha, B. Twinned growth of ScN thin films on lattice-matched GaN substrates. Mater. Res. Bull. 2021, 143, 111443.DOI
  45. [45]Lupina, L.; Zoellner, M. H.; Niermann, T.; Dietrich, B.; Capellini, G.; Thapa, S. B.; Haeberlen, M.; Lehmann, M.; Storck, P.; Schroeder, T. Zero lattice mismatch and twin-free single crystalline ScN buffer layers for GaN growth on silicon. Appl. Phys. Lett. 2015, 107, 201907.DOI
  46. [46]Dinh, D. V.; Conroy, M.; Zubialevich, V. Z.; Petkov, N.; Holmes, J. D.; Parbrook, P. J. Single phase (11̄22) AlN grown on (101̄0) sapphire by metalorganic vapour phase epitaxy. J. Cryst. Growth 2015, 414, 94.
  47. [47]Dinh, D. V.; Amano, H.; Privostek, M. MOVPE growth and high-temperature annealing of (101̄0) AlN layers on (101̄0) sapphire. J. Cryst. Growth 2018, 502, 14.
  48. [48]Stadelmann, P. A. EMS - a software package for electron diffraction analysis and HREM image simulation in materials science. Ultramicroscopy 1987, 21, 131.DOI
  49. [49]Stadelmann, P. JEMS (JEMS-SWISS, Chemin Rouge 15 CH-1805 Jongny Switzerland, n.d.); Available at: https://www.jems-swiss.ch.
  50. [50]Wu, F.; Tyagi, A.; Young, E. C.; Romanov, A. E.; Fujito, K.; DenBaars, S. P.; Nakamura, S.; Speck, J. S. Misfit dislocation formation at heterointerfaces in (Al,In)GaN heteroepitaxial layers grown on semipolar free-standing GaN substrates. J. Appl. Phys. 2011, 109, 033505.DOI
  51. [51]De Mierry, P.; Guehne, T.; Nemoz, M.; Chenot, S.; Beraudo, E.; Nataf, G. Comparison between polar (0001) and semipolar (11̄22) nitride blue–green light-emitting diodes grown on c- and m-plane sapphire substrates. Jpn. J. Appl. Phys. 2009, 48, 031002.DOI
  52. [52]Dasilva, Y. A. R.; Chauvat, M. P.; Ruterana, P.; Lahourcade, L.; Monroy, E.; Nataf, G. Defect structure in heteroepitaxial semipolar (11̄22) (Ga,Al)N. J. Phys.: Condens. Matter 2010, 22, 355802.
  53. [53]Moram, M. A.; Barber, Z. H.; Humphreys, C. J.; Joyce, T. B.; Chalker, P. R. Young’s modulus, Poisson’s ratio, and residual stress and strain in (111)-oriented scandium nitride thin films on silicon. J. Appl. Phys. 2006, 100.
  54. [54]Pietsch, U.; Unger, K. The influence of free carriers on the equilibrium lattice parameter of semiconductor materials. Phys. Status Solidi A 1983, 80, 165–172.
  55. [55]Van De Walle, C. G. Effects of impurities on the lattice parameters of GaN. Phys. Rev. B 2003, 68, 165209.DOI
  56. [56]Momma, K.; Izumi, F. VESTA 3 for three-dimensional visualization of crystal, volumetric and morphology data. J. Appl. Crystallogr. 2011, 44, 1272.
  57. [57]Paszkowicz, W.; Podsiadło, S.; Minikayev, R. Rietveld-refinement study of aluminium and gallium nitrides. J. Alloys Compd. 2004, 382, 100.DOI
  58. [58]Nilsson, D.; Janzén, E.; Kakanakova-Georgieva, A. Lattice parameters of AlN bulk, homoepitaxial and heteroepitaxial material. J. Phys. D: Appl. Phys. 2016, 49, 175108.DOI
  59. [59]Hull, D.; Bacon, D. J. Introduction to dislocations (fifth edition); Butterworth-Heinemann: Oxford, England, UK, 2011; pp 85–107.
  60. [60]Li, Z.; Shao, S.; Li, N.; McCall, K.; Wang, J.; Zhang, S. X. Single crystalline nanostructures of topological crystalline insulator SnTe with different facets and morphologies. Nano Lett. 2013, 13, 5443–5448.
  61. [61]Lifshitz, E. M.; Kosevich, A. M.; Pitaevskii, L. P. Theory of elasticity; Butterworth-Heinemann, Oxford, England, UK, 1986.
  62. [62]Zangwill, A. Physics at surfaces; Cambridge University Press: Cambridge, England, UK, 1988.
  63. [63]Tersoff, J.; LeGoues, F. K. Competing relaxation mechanisms in strained layers. Phys. Rev. Lett. 1994, 72, 3570–3573.
  64. [64]Zhang, Z.; Lagally, M. G. Atomistic processes in the early stages of thin-film growth. Science 1997, 276, 377–383.
  65. [65]Xinh, N. X.; Maradudin, A. A.; Coldwell-Horsfall, R. A. Impurity induced first order Raman scattering of light by alkali-halide crystals. J. Phys. 1965, 26, 717.
  66. [66]Todorov, N. D.; Abrashev, M. V.; Ivanov, V. G.; Tsutsumanova, G. G.; Marinova, V.; Wang, Y.-Q.; Iliev, M. N. Comparative Raman study of isostructural YCrO₃ and YMnO₃: Effects of structural distortions and twinning. Phys. Rev. B 2011, 83, 224303.
  67. [67]Travaglini, G.; Marabelli, F.; Monnier, R.; Kaldis, E.; Wachter, P. Electronic structure of ScN. Phys. Rev. B 1986, 34, 3876.
  68. [68]Gall, D.; Stoehr, M.; Greene, J. E. Vibrational modes in epitaxial Ti₁−ₓScₓN(001) layers: An ab initio calculation and Raman spectroscopy study. Phys. Rev. B 2001, 64, 174302.DOI
  69. [69]Paudel, T. R.; Lambrecht, W. R. L. Calculated phonon band structure and density of states and interpretation of the Raman spectrum in rocksalt ScN. Phys. Rev. B 2009, 79, 085205.
  70. [70]Saha, B.; Acharya, J.; Sands, T. D.; Waghmare, U. V. Electronic structure, phonons, and thermal properties of ScN, ZnN, and HfN: A first-principles study. J. Appl. Phys. 2010, 107, 033715.
  71. [71]Van Koughnet, K.; Trodahl, H. J.; Holmes-Hewett, W. F.; Ruck, B. J. Defect-activated versus intrinsic Raman spectra of GdN and LuN. Phys. Rev. B 2023, 108, 064306.DOI
  72. [72]Grümbel, J.; Goldhahn, R.; Feneberg, M.; Oshima, Y.; Dubroka, A.; Ramsteiner, M. Band gaps and phonons of quasi-bulk rocksalt ScN. Phys. Rev. Mater. 2024, 8, L071601.DOI
  73. [73]Li, C.; Broido, D. Phonon thermal transport in transition-metal and rare-earth nitride semiconductors from first principles. Phys. Rev. B 2017, 95, 205203.
  74. [74]Snyder, G. J.; Toberer, E. S. Complex thermoelectric materials. Nat. Mater. 2008, 7, 105–114.DOI
  75. [75]Saha, B.; Garbrecht, M.; Perez-Taborda, J. A.; Fawey, M. H.; Koh, Y. R.; Shakouri, A.; Martin-Gonzalez, M.; Hultman, L.; Sands, T. D. Compensation of native donor doping in ScN: Carrier concentration control and p-type ScN. Appl. Phys. Lett. 2017, 110, 252104.
  76. [76]Mu, S.; Rowberg, A. J. E.; Leveillee, J.; Giustino, F.; Van de Walle, C. G. First-principles study of electron transport in ScN. Phys. Rev. B 2021, 104, 075118.
  77. [77]Askerov, B. M. Electron transport phenomena in semiconductors; World Scientific: Singapore, 1994; pp 78–167.
  78. [78]Giustino, F. Electron-phonon interactions from first principles. Rev. Mod. Phys. 2017, 89, 015003.

Paper details

vlnc:W_c4g92bx9
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents