betaFeedback

WorksPhysics and Astronomy

Grain boundary stresses in elastic materials

Abstract

A simple analytical model of intergranular normal stresses is proposed for a general elastic polycrystalline material with arbitrary shaped and randomly oriented grains under uniform loading. The model provides algebraic expressions for the local grain-boundary-normal stress and the corresponding uncertainties, as a function of the grain-boundary type, its inclination with respect to the direction of external loading and material-elasticity parameters. The knowledge of intergranular normal stresses is a necessary prerequisite in any local damage modeling approach, e.g., to predict the intergranular stress-corrosion cracking, grain-boundary sliding or fatigue-crack-initiation sites in structural materials. The model is derived in a perturbative manner, starting with the exact solution of a simple setup and later successively refining it to account for higher order complexities of realistic polycrystalline materials. In the simplest scenario, a bicrystal model is embedded in an isotropic elastic medium and solved for uniaxial loading conditions, assuming 1D Reuss and Voigt approximations on different length scales. In the final iteration, the grain boundary becomes a part of a 3D structure consisting of five 1D chains with arbitrary number of grains and surrounded by an anisotropic elastic medium. Constitutive equations can be solved for arbitrary uniform loading, for any grain-boundary type and choice of elastic polycrystalline material. At each iteration, the algebraic expressions for the local grain-boundary-normal stress, along with the corresponding statistical distributions, are derived and their accuracy systematically verified and validated against the finite element simulation results of different Voronoi microstructures.

Introduction

Predicting damage initiation and its progression in structural materials relies heavily on the knowledge of local mechanical stresses present in the material. For particular aging processes, the material damage is initiated at the grain boundaries (GBs), where intergranular microcracks form. With time, these microcracks may grow along the GBs and combine into larger macroscopic cracks, which can eventually compromise the structural integrity of the entire component under load. Since microcracks are invisible to non-destructive inspection techniques, the detection instruments can only reveal the existence of macroscopic cracks, which roughly appear in the final 10% of the component’s lifetime. Having accurate models for predicting the component’s susceptibility to microcracking in its earlier stages is therefore of uttermost importance in many different applications, as this could reduce the costs needed for frequent inspections and replacements. InterGranular Stress-Corrosion Cracking (IGSCC) is one of the most significant ageing-degradation mechanisms. It corresponds to the initiation and propagation of microcracks along the GBs and is common in alloys, that are otherwise typically corrosion-resistant (austenitic stainless steels [1, 2, 3, 4, 5], zirconium alloys [6, 7], nickel based alloys [8, 9, 10, 11], high strength aluminum alloys [12, 13] and ferritic steels [14, 15]). The IGSCC is a multi-level process that includes electro-chemical, micro-mechanical and thermo-mechanical mechanisms. The activation of these mechanisms depends on material properties, corrosive environment and local stress state. It is believed that GB stresses are the driving force of intergranular cracking, therefore they need to be accurately determined, in order to make quantitative predictions about IGSCC initiation. Various approaches to IGSCC-initiation modeling are being considered. One such approach is to treat IGSCC phenomenon on a local GB scale, where GB-normal stresses σnn\sigma_{nn} can be studied separately (decoupled) from the environmental effects that degrade the GB strength σc\sigma_c; IGSCC ≈F(σnn)⋅F(σc)\approx\mathcal{F}(\sigma_{nn}) \cdot\mathcal{F}(\sigma_c). A GB-normal stress σnn\sigma_{nn} is defined here as a component of local stress tensor along the GB-normal direction, i.e., perpendicular to the GB plane.1 Hence, a single stress-based criterion for a local IGSCC initiation can be assumed on every GB: IGSCC gets initiated wherever σnn>σc\sigma_{nn} > \sigma_c, with both these quantities being local in a sense, that they in principle depend on the position of the GB within the aggregate. The introduced local criterion can be used to evaluate the probability, that a randomly selected GB on a component’s surface, where it is in contact with the corrosive environment, is overloaded (or soon-to-be cracked). This probability can be estimated by calculating a fraction η\eta of GBs with σnn>σc\sigma_{nn} > \sigma_c as η=∫σc∞PDF⁡(σnn)dσnn\eta= \int_{\sigma_c}^{\infty} \operatorname{PDF}(\sigma_{nn})\mathrm{d}\sigma_{nn}, for the assumed probability-density function PDF⁡(σnn)\operatorname{PDF}(\sigma_{nn}). If a fraction of overloaded GBs exceeds a threshold value, η>ηf\eta> \eta_f, a specimen-sized crack may develop, possibly resulting in a catastrophic failure of the component. This approach, based on the accurate knowledge of GB-normal stresses, seems feasible when a GB strength σc\sigma_c is known and approximately constant within the examined surface section. Unfortunately, this is not the case in real materials.

Measurements have shown that different GBs show different IGSCC sensitivities [5, 16, 17, 18], implying that GB strength σc\sigma_c depends not only on the material and environmental properties but also strongly on a GB type; σc=F\sigma_c = \mathcal{F}(GB type, material, environment). Here, a GB type denotes a GB microstructure (inter-atomic arrangements in the vicinity of the GB), which affects the GB energy and, eventually, its strength σc\sigma_c. In the continuum limit, five parameters are needed to define a GB neighborhood: four parameters are required to specify a GB plane in crystallographic systems of the two adjacent grains and one parameter defines a twist rotation between the associated crystal lattices about the plane normal. In principle, the term “GB type” thus refers to GBs with the same GB strength. Sometimes it is convenient to specify a GB type by less than five parameters (e.g., when the values of skipped parameters do not affect the σnn\sigma_{nn} distribution). For instance, in the [abc]−[def][abc]-[def] GB type, with a GB-plane normal along the [abc][abc] direction in one grain and [def][def] direction in the other grain, the twist angle can be assumed random (and thus remains unspecified).

In addition to σc\sigma_c being a function of GB type, also the distributions of GB-normal stresses should be evaluated for different GB types in order to later perform a meaningful calculation of fraction η\eta. Hence, PDF⁡(σnn)=F\operatorname{PDF}(\sigma_{nn}) = \mathcal{F}(GB type, applied stress, material). Since exact general solutions for both the local σnn\sigma_{nn} and statistical PDF⁡(σnn)\operatorname{PDF}(\sigma_{nn}) are too complex to be derived analytically, researchers have restricted themselves to numerical simulations limited to few selected materials and specific (usually uniaxial) loading conditions.

Crystal-plasticity finite element (FE) simulations [19, 20, 21, 22, 23, 24] and crystal-plasticity fast Fourier transform simulations [25, 26] have been used to obtain intergranular stresses on random GBs in either synthetic or realistic polycrystalline aggregates, providing valuable information for IGSCC initiation in those specific cases. In particular, the fluctuations of intergranular normal stresses (the widths of PDF⁡(σnn)\operatorname{PDF}(\sigma_{nn})) have been found to depend primarily on the elasto-plastic anisotropy of the grains with either cubic [22, 23, 24] or hexagonal lattice symmetries [24].

Although the computationally demanding simulations can provide accurate results, such an approach deems impractical for a general case and provides little insights into involved physics. Thus, efforts have been made to identify most influential parameters affecting the GB-normal stresses on any single GB type [27, 28]. In the elastic regime of grains with cubic lattice symmetry, Zener elastic anisotropy index AA [29] and effective GB stiffness E12E_{12}, measuring the average stiffness of GB neighborhood along the GB-normal direction, have been identified and demonstrated to be sufficient for quantifying normal-stress fluctuations on any GB type in a given material under uniaxial external loading [28]. The empirical relation (still lacking a satisfactory explanation) has been established for the standard deviation of σnn\sigma_{nn} distribution evaluated on [abc]−[def][abc]-[def] GBs, which is a function of AA and E12E_{12}. On the contrary, the mean value of the same σnn\sigma_{nn} distribution has been shown to be independent of the chosen material and/or the GB type on which it is calculated.

To account for elastic–perfectly plastic grains at applied tensile yield stress, a simple Schmid-Modified Grain-Boundary-Stress model has been proposed [27] to investigate the initiation of an intergranular crack, based on a normal stress acting at GB. The model considers combined effects of GB-plane orientation and grain orientations through their Schmid factors. It has been pointed out, that intergranular cracks occur most likely at highly stressed GBs. In other similar studies [5, 30, 31], the same model has been used to discuss crack initiation in austenitic stainless steel, concluding that initiation sites coincide with the most highly stressed GBs.

Building upon partial results, limited to either specific loading conditions [27, 28] and/or specific grain-lattice symmetries [28], the goal of this study is to develop a model of GB-normal stresses, that would provide accurate analytic or semi-analytic expressions for σnn\sigma_{nn}, with the corresponding statistical measure PDF⁡(σnn)\operatorname{PDF}(\sigma_{nn}), depending on a general GB type, general applied stress and general elastic polycrystalline material. Once the knowledge of GB strength σc\sigma_c becomes available, the resulting expressions will be directly useful in the mechanistic modeling of GB-damage initiation (such as IGSCC2{}^{2}) and should therefore become a quick and reliable tool to all the experts dealing with local damage modeling and characterization.

The paper is structured as follows: in Sec. II typical material and GB-type effects on GB-normal stresses are introduced. In Sec. III the perturbative framework for predicting GB-normal stresses is developed, providing analytical and semi-analytical models along with their solutions. In Sec. IV the upgraded models are verified with FE-simulation results. Practical implications are discussed in Sec. V and in Sec. VI some concluding remarks are given. All technical details are deferred to the set of Appendices.

Material and grain boundary type effects on intergranular normal stresses

The anisotropic elasticity of crystals is governed by the generalized Hooke’s law, σij=Cijklεkl\sigma_{ij} = C_{ijkl}\varepsilon_{kl}, where CijklC_{ijkl} is a 3D fourth-order stiffness tensor. Depending on the symmetry of the underlying grain lattice, CijklC_{ijkl} can be expressed in terms of two (isotropic), three (cubic), or more (up to 21 for triclinic) independent elastic parameters. All grains in a polycrystalline aggregate are assigned the same elastic material properties, but different, random crystallographic orientations (no texture). However, for practical purposes, we artificially increase the share of GBs of a certain type in our finite element aggregate models, by imposing specific orientations to a relatively small fraction of grains.

In the continuum limit3, a general GB type is defined by five independent parameters, which specify the orientations of two nearest grains relative to the GB plane. It can be expressed in the form of [abc]−[def]−Δω[abc]-[def]-\Delta\omega GBs, where their GB plane is the [abc][abc] plane in one grain and [def][def] plane in the other grain, with Δω\Delta\omega denoting a relative twist of the two grain orientations about the GB normal.4

Due to topological constraints, not all GBs can be assigned the same GB character. In practice, a particular

[abc]−[def]−Δω[abc]-[def]-\Delta\omega GB type can be ascribed to at most ∼17%\sim17\% of the GBs in a given aggregate, with the remaining GBs being of random type (i.e., defined by two randomly oriented neighboring grains). A polycrystalline aggregate and two particular GB types are visualized in Figure 1.

3D periodic Voronoi aggregate and two grain boundaries

Figure 1. (a) 3D periodic Voronoi aggregate with 4000 grains used in this study. Different grains are denoted by different colors. Finite element mesh is shown for one selected grain. Visualization of two different GBs with fixed GB plane (with normal nn) but different crystallographic orientations: (b) [1]-[1]-30° GB and (c) [111]-[111]-30° GB.

The constitutive equations of the generalized Hooke’s law are solved numerically for a chosen uniform loading with FE solver Abaqus [32]. The obtained stresses σ\sigma, corresponding to the nearest integration points of a particular GB kk, are then used to produce a single value σnn(k)\sigma_{nn}(k) as their weighted average. Besides local stresses σnn(k)\sigma_{nn}(k), first two statistical moments of PDF(σnn\sigma_{nn}), the mean value and standard deviation, are calculated for the distribution of stresses σnn\sigma_{nn} on GBs of a chosen, over-represented [abc]−[def]−Δω[abc]-[def]-\Delta\omega GB type, whose density was artificially boosted (see Appendix A for further details).

Figs. 2 and 3 show typical (strong) effects of different GB types and different materials on both, local stresses σnn\sigma_{nn} and the corresponding stress distributions PDF(σnn\sigma_{nn}), for the assumed macroscopic uniaxial tensile loading Σ\Sigma. In Figure 2, a comparison of different [abc]−[def][abc]-[def] GB types is made, with Δω\Delta\omega assumed random. Each value of GB index refers to a particular GB within the aggregate of fixed grain topology, shown in Figure 1(a). In this way, the effect of the GB type can be isolated from other contributions. While the mean stress is independent of the GB type (with ⟨σnn⟩=Σ/3\langle\sigma_{nn}\rangle= \Sigma/3 for all types), the stress fluctuations are much larger on the (stiffest) [111]-[111] GBs than on the (softest) [1]-[1] GBs [28].

Figure 2. (a) Normalized local stress responses σnn/Σ\sigma_{nn}/\Sigma and (b) their statistical distributions PDF⁡(σnn/Σ)\operatorname{PDF}(\sigma_{nn}/\Sigma) in a polycrystalline lithium under macroscopic tensile loading Σ\Sigma for 3 different GB types. Large influence of a chosen GB type and poor prediction capability of the isotropic model (σnn/Σ=cos⁡2θ\sigma_{nn}/\Sigma= \cos^{2}\theta) are clearly visible. In panel (a) the results are shown for just 15 randomly selected GBs of each type (GB index).

A similar behavior is observed in Figure 3, where the effect of different material properties is isolated from other contributions by comparing σnn\sigma_{nn} on identical GBs. All stress distributions PDF(σnn\sigma_{nn}) are again centered around ⟨σnn⟩=Σ/3\langle\sigma_{nn}\rangle= \Sigma/3, while they are at the same time getting considerably wider with increasing grain anisotropy [28].

Figure 3. Similarly as in Figure 2, but evaluated on [111]-[111] GB type in different materials to demonstrate the effect of their elastic properties. Panel (b) shows how isotropic model begins to fail with the growing anisotropy of the grains.

In most cases depicted in Figure 2 and Figure 3, a poor prediction capability of the isotropic model5 is observed, implying that local GB stresses are non-trivially dependent on the GB type, material properties and loading conditions.

Perturbative model of grain boundary normal stresses

Assumptions

To develop an accurate prediction for σnn\sigma_{nn} (and the corresponding PDF(σnn\sigma_{nn})), a step-by-step approach is taken, inspired by perturbation theory. In this sense, the solution for σnn(k)\sigma_{nn}^{(k)}, starting from the trivial isotropic-grain solution σnn(0)\sigma_{nn}^{(0)}, is refined in each successive step kk by considering the contribution of more distant grains. To provide an analytic solution, sensible approximations and assumptions are used. For example, following Saint Venant’s principle, the effects of more distant neighborhood on a GB are described in less detail, using only average quantities such as elastic grain anisotropy AuA^{u} [33] or isotropic bulk stiffness ⟨E⟩\langle E\rangle. The strategy for building a perturbative model is shown schematically in Figure 4. In the simplest approximation (k=0k = 0), the neighborhood of a chosen GB can be modeled as isotropic, in which case the only relevant degree of freedom is the orientation of the GB plane. In the next order iteration (k=1k = 1), the two (anisotropic) grains enclosing the GB are considered, while their combined (axial) strain is assumed equal as if both grains were made from (isotropic) bulk material.

Perturbation-theory based strategy for finding GB-normal stress

Figure 4. Perturbation-theory based strategy for finding GB-normal stress σnn(k)\sigma_{nn}^{(k)}. In each successive step kk, a more complex GB neighborhood is taken into account. For simplicity, the scheme presented here is only 2D and subjected to tensile loading Σ\boldsymbol{\Sigma}, but in practise a 3D case for a general uniform loading is considered.

This assumption works well for average grains, but the stiffer or softer the grains in the pair are, the more it starts to fail. To relax that condition, in the next order iteration (k=2k = 2), “buffer” grains are introduced along the GB-normal (axial) direction. Then not only bicrystal pair, but the whole axial chain (containing also the buffer grains) is supposed to deform as if it was made from bulk material. In a similar manner, buffer grains are added also along the transverse directions, forming transverse chains of grains whose axial strain is constrained by the bulk (k=3k = 3).

In the isotropic-grain solution (k=0k = 0), the GB-normal stress is equal to the externally applied stress projected onto a GB plane, σnn(0)=Σzz\sigma_{nn}^{(0)} = \Sigma_{zz}, which for uniaxial loading Σ\Sigma translates to σnn(0)=Σcos⁡2θ\sigma_{nn}^{(0)} = \Sigma\cos^{2}\theta, where θ\theta is the angle between the GB normal and loading direction. The isotropic-grain solution may be a good initial approximation, but it turns to be a poor solution for moderate and highly anisotropic materials, see Figure 2 and Figure 3.

To obtain higher-order (k>0k > 0) solutions σnn(k)\sigma_{nn}^{(k)}, the effect of two nearest grains enclosing the GB is considered in more detail, while the effect of more distant, buffer grains is accounted for less rigorously. Instead of a full 3D solution, several partial 1D solutions are obtained simultaneously and properly combined to accurately approximate σnn(k)\sigma_{nn}^{(k)}. Schematically, the corresponding general model can be viewed in Figure 5, as composed of one axial chain of length Ln+2L_n + 2 and four lateral chains of length Lt+1L_t + 1 crossing the two grains, that are adjacent to GB.

Figure 5. A 2D sketch of perturbative model for GB stresses, consisting of two anisotropic grains of unit size, enclosing the GB, and several isotropic buffer grains of variable length, composing one axial chain of length Ln+2L_n+2 and two (four in 3D) transverse chains of length Lt+1L_t+1. Stresses and strains are assumed constant within the grains. Total strain of each chain is prescribed to match that of isotropic bulk of the same length and under the same external loading (Voigt-like assumption on a chain-length scale). 3D coupling of the chains with the surrounding bulk is modeled by assuming variable chain stiffness. External loading Σ\boldsymbol{\Sigma} is dressed by fluctuations f\mathbf{f}.

The chains are assumed decoupled from each other, but they interact with the surrounding bulk. The bulk is taken as isotropic, with average (bulk) properties, such as elastic stiffness ⟨E⟩\langle E\rangle and Poisson’s ratio ⟨ν⟩\langle\nu\rangle. The chain-bulk interaction is, in the first approximation (i.e., without lateral 3D coupling), assumed to be along the chain direction. It constrains the total strain of the chain to that of the isotropic bulk. This boundary condition corresponds to the Voigt-like assumption, but on a chain-length scale.

Buffer grains are assumed isotropic as well, but with elastic stiffness EbE_b and Poisson’s ratio νb\nu_b, both corresponding to the average response of a chain with LnL_n (or LtL_t) randomly oriented grains. However, when accounting for the lateral 3D effects (cf. Sec. IIID 1), the chains are allowed to interact also laterally with the bulk and in the limit of long chains both parameters approach those of the bulk, Eb∼⟨E⟩E_b \sim\langle E\rangle and νb∼⟨ν⟩\nu_b \sim\langle\nu\rangle.

The two grains on either side of the GB are assumed anisotropic, with their crystallographic orientations determining the [abc]−[def][abc]-[def]-Δω\Delta\omega type of the corresponding GB.

Finally, the stresses and strains are considered homogeneous within all the grains. In addition, a general analytical expression for σnn(k)\sigma_{nn}^{(k)} is derived by applying a reduced set of boundary conditions. To facilitate a simple, closed-form solution for σnn(k)\sigma_{nn}^{(k)}, only the conditions for stresses are imposed at the GB, while those for strains are neglected. Hence, the stress equilibrium is fulfilled everywhere in the model, while the strain compatibility at the GB is not guaranteed. These assumptions will be justified a posteriori by comparing the model results with those from numerical simulations.

Analytical models

General setup

Analytical expressions for σnn(k)\sigma_{nn}^{(k)} are presented in the GB coordinate system (x,y,z)(x,y,z) with zz-axis along the GB normal. All quantities expressed in the local-grain coordinate system (n1,n2,n3)(n_1,n_2,n_3), aligned with crystallographic (eigen-)axes, and the laboratory coordinate system (X,Y,Z)(X,Y,Z), therefore need to be appropriately transformed using the following (passive) rotations Rcry\mathbf{R}^{\mathrm{cry}} and Rlab\mathbf{R}^{\mathrm{lab}}, respectively (see also Figure 6),

Definition of three coordinate systems

Figure 6. Definition of three coordinate systems: laboratory coordinate system (X,Y,Z)(X,Y,Z), local-grain coordinate system (n1,n2,n3)(n_1,n_2,n_3), and GB coordinate system (x,y,z)(x,y,z). The latter can be arbitrarily chosen with respect to the twist angle τ\tau about the GB normal n^∥z^\hat{\mathbf{n}}\Vert\hat{\mathbf{z}}. Passive rotations Rlab\mathbf{R}^{\mathrm{lab}} and Rcry\mathbf{R}^{\mathrm{cry}} transform external and local-grain quantities, respectively, to the GB coordinate system. Since in the following, two grains will be considered, four coordinate systems will be in use, namely one crystallographic system for each grain, together with associated rotations Rcry,abc\mathbf{R}^{\mathrm{cry},abc} and Rcry,def\mathbf{R}^{\mathrm{cry},def}.

References

  1. [1]H. Nishioka, K. Fukuya, K. Fujii, and T. Torimaru, IASCC initiation in highly irradiated stainless steels under uniaxial constant load conditions, J. Nuc. Sci. and Tech. 45, 1072 (2008).DOI
  2. [2]M. Le Millier, O. Calonne, J. Crépin, C. Duhamel, L. Fournier, F. Gaslain, E. Héripré, O. Toader, Y. Vidalenc, and G. Was, Influence of strain localization on IASCC of proton irradiated 304L stainless steel in simulated PWR primary water, in 16th International Conference on Environmental Degradation of Materials in Nuclear Power Systems - Water Reactors (2013).
  3. [3]K. Stephenson and G. Was, Crack initiation behavior of neutron irradiated model and commercial stainless steels in high temperature water, J. Nuc. Mat. 444, 331 (2014).
  4. [4]J. Gupta, J. Hure, B. Tanguy, L. Laffont, M. Lafont, and E. Andrieu, Evaluation of stress corrosion cracking of irradiated 304 stainless steel in PWR environment using heavy ion irradiation, J. Nuc. Mat. 476, 82 (2016).DOI
  5. [5]T. Fujii, K. Tohgo, Y. Mori, Y. Miura, and Y. Shimamura, Crystallographic and mechanical investigation of intergranular stress corrosion crack initiation in austenitic stainless steel, Mat. Sci. Eng. A 751, 160 (2019).DOI
  6. [6]B. Cox, Environmentally induced cracking of zirconium alloys, Tech. Rep. (Atomic Energy of Canada Limited, 1970).
  7. [7]B. Cox, Environmentally-induced cracking of zirconium alloys - A review, J. Nuc. Mat 170, 1 (1990).DOI
  8. [8]D. Van Rooyen, Review of the stress corrosion cracking of inconel 600, Corrosion 31, 327 (1975).DOI
  9. [9]C. Shen and P. Shewmon, A mechanism for hydrogen-induced intergranular stress corrosion cracking in alloy 600, Metall. Trans. A 21, 1261 (1990).DOI
  10. [10]J. Panter, B. Viguier, J. Cloué, M. Foucault, P. Combrade, and E. Andrieu, Influence of oxide films on primary water stress corrosion cracking initiation of alloy 600, J. Nuc. Mat. 348, 213 (2006).DOI
  11. [11]IAEA, Stress corrosion cracking in light water reactors: Good practices and lessons learned, NP-T-3.13 (IAEA Nuclear Energy Series, 2011).
  12. [12]M. Speidel, Stress corrosion cracking of aluminum alloys, Metallurgical and Materials Transactions A 6A, 631 (1975).
  13. [13]T. Burleigh, The postulated mechanisms for stress corrosion cracking of aluminum alloys: A review of the literature 1980-1989, Corrosion 47, 89 (1991).
  14. [14]Z. Wang and A. Atrens, Initiation of stress corrosion cracking for pipeline steels in a carbonate-bicarbonate solution, Metallurgical and Materials Transactions A 27A, 2686 (1996).DOI
  15. [15]M. Arafin and J. Szpunar, A new understanding of intergranular stress corrosion cracking resistance of pipeline steel through grain boundary character and crystallographic texture studies, Corrosion Science 51, 119 (2009).DOI
  16. [16]S. Rahimi and T. J. Marrow, Effects of orientation, stress and exposure time on short intergranular stress corrosion crack behaviour in sensitised type 304 austenitic stainless steel, Fatigue Fract. Eng. Mater. Struct. 35, 359 (2011).DOI
  17. [17]S. Rahimi, D. L. Engelberg, J. A. Duff, and T. J. Marrow, In situ observation of intergranular crack nucleation in a grain boundary controlled austenitic stainless steel, Journal of Microscopy 233, 423 (2009).DOI
  18. [18]T. Liu, S. Xia, Q. Bai, B. Zhou, Y. Lu, and T. Shoji, Evaluation of grain boundary network and improvement of intergranular cracking resistance in 316L stainless steel after grain boundary engineering, Materials 12, 242 (2019).DOI
  19. [19]O. Diard, S. Leclercq, G. Rousselier, and G. Cailletaud, Distribution of normal stress at grain boundaries in multicrystals: Application to an intergranular damage modeling, Comp. Mat. Sci. 25, 73 (2002).DOI
  20. [20]O. Diard, S. Leclercq, G. Rousselier, and G. Cailletaud, Evaluation of finite element based analysis of 3D multicrystalline aggregates plasticity. Application to crystal plasticity model identification and the study of strain fields near grain boundaries, Int. J. Plasticity 21, 691 (2005).
  21. [21]A. Kanjarla, P. Van Houtte, and L. Delannay, Assessment of plastic heterogeneity in grain interaction models using crystal plasticity finite element method, Int. J. Plasticity 26, 1220 (2010).DOI
  22. [22]D. Gonzalez, I. Simonovski, P. Withers, and J. Quinta da Fonseca, Modelling the effect of elastic and plastic anisotropies on stresses at grain boundaries, Int. J. Plasticity 61, 49 (2014).
  23. [23]J. Hure, S. El Shawish, L. Cizelj, and B. Tanguy, Intergranular stress distributions in polycrystalline aggregates of irradiated stainless steel, J. Nuc. Mat. (2016).DOI
  24. [24]S. El Shawish and J. Hure, Intergranular normal stress distribution in untextured polycrystalline aggregates, Eur. J. Mech. / A Solids 72, 354 (2018).DOI
  25. [25]R. Lebensohn, A. Kanjarla, and P. Eisenlohr, An elastoviscoplastic formulation based on fast fourier transforms for the prediction of micromechanical fields in polycrystalline materials, Int. J. Plasticity 32-33, 59 (2012).DOI
  26. [26]D. Liang, J. Hure, A. Courcelle, S. El Shawish, and B. Tanguy, A micromechanical analysis of intergranular stress corrosion cracking of an irradiated austenitic stainless steel, under review (2020).DOI
  27. [27]E. A. West and G. S. Was, A model for the normal stress dependence of intergranular cracking of irradiated 316L stainless steel in supercritical water, Journal of Nuclear Materials 408, 142 (2011).DOI
  28. [28]S. El Shawish, T. Mede, and J. Hure, A single grain boundary parameter to characterize normal stress fluctuations in materials with elastic cubic grains, European Journal of Mechanics, A/Solids 89 (2021).DOI
  29. [29]C. Zener, Elasticity and Anelasticity of Metals (University of Chicago, 1948).
  30. [30]A. Stratulat, J. A. Duff, and T. J. Marrow, Grain boundary structure and intergranular stress corrosion crack initiation in high temperature water of a thermally sensitised austenitic stainless steel, observed in situ, Corrosion Science 85, 428 (2014).DOI
  31. [31]Z. Zhang, S. Xia, Q. Bai, T. Liu, H. Li, B. Zhou, L. Wang, and W. Ma, Effects of 3D grain boundary geometrical angles and the net normal stress on intergranular stress corrosion cracking initiation in a 316 stainless steel, Ma- terials Science and Engineering: A 765, 138277 (2019).
  32. [32]Simulia, ABAQUS 6.14-2 (2016).
  33. [33]S. I. Ranganathan and M. Ostaja-Starzewski, Universal elastic anisotropy index, Phys. Rev. Lett. 101, 055504 (2008).
  34. [34]S. El Shawish, Probabilistic two-scale modeling approach for predicting grain boundary damage initiation in complex geometries, In preparation.
  35. [35]M. Koyama, Z.-J. Xi, Y. Yoshida, N. Yoshimura, K. Ushioda, and H. Noguchi, Intergranular fatigue crack initiation and its associated small fatigue crack propagation in water-quenched fe–c fully ferritic steel, ISIJ International 55, 2463 (2015).
  36. [36]E. Kröner, Berechnung der elastischen konstanten des vielkristalls aus den konstanten des einkristalls, Z. Physik 151, 504 (1958).DOI
  37. [37]A. Hershey, The elasticity of an isotropic aggregate of anisotropic cubic crystals, J. Appl. Mech. 21, 236 (1954).DOI
  38. [38]R. Quey, P. R. Dawson, and F. Barbe, Large-scale 3D random polycrystals for the finite element method: Generation, meshing and remeshing, Comput. Methods Appl. Mech. Eng. 200, 1729 (2011).DOI
  39. [39]S. El Shawish, P. G. Vincent, H. Moulinec, L. Cizelj, and L. Gélébart, Full-field polycrystal plasticity simulations of neutron-irradiated austenitic stainless steel: A comparison between fe and fft-based approaches, J. Nuc. Mat. 529, 151927 (2020).DOI
  40. [40]A. F. Bower, Applied Mechanics of Solids (Taylor & Francis Group, 2010).
  41. [41]G. Simmons and H. Wang, Single Crystal Elastic Constants and Calculated Aggregate Properties. A Handbook (The MIT Press, 1971).

Paper details

vlnc:W_ckcz4r3t
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents