betaFeedback

WorksPhysics and Astronomy

Experiment demonstration of tilt-to-length coupling suppression by beam-alignment-mechanism

Abstract

Tilt-to-length (TTL) noise, caused by angular jitter and misalignment, is a major noise source in the inter-satellite interferometer for gravitational wave detection. However, the required level of axis alignment of the optical components is beyond the current state of the art. A set of optical parallel plates, called beam alignment mechanism (BAM), is proposed by LISA to compensate for the alignment error. In this paper, we show a prototype design of the BAM and demonstrate its performance in a ground-based optical system. We derive the BAM theoretical model, which agrees well with the numerical simulation. Experimental results reveal that the BAM can achieve lateral displacement compensation of the optical axis with a resolution of \SI{1}{\micro\meter} across a \D{dynamic} range of about \SI{0.5}{\milli\meter}. Furthermore, the TTL coefficient is reduced from about \SI{0.3}{\milli\meter/\radian} to about \SI{5}{\micro\meter/\radian}, satisfying the preliminary requirements for LISA and TianQin. These findings confirm the efficacy of the BAM in suppressing TTL noise, offering a promising solution for space-based gravitational wave detection.

Introduction

Gravitational wave detection has opened new windows into the universe, enabling the observation of phenomena such as black hole mergers and neutron star collisions [1]. Space-based gravitational wave detectors like LISA [2], TianQin [3, 4] and Taiji [5] are poised to extend the observation window to low-frequency gravitational waves, enabling the detection of massive black hole mergers and the early universe’s stochastic gravitational wave background. However, despite the potential breakthroughs, space-based GW detectors face numerous technical challenges, with tilt-to-length (TTL) coupling noise emerging as one of the primary limitations for their sensitivity.

TTL coupling arises when angular misalignments in the optical system introduce unwanted length changes in the interferometric measurements [6, 7]. Among the various TTL coupling mechanisms, the first-order term in the Taylor expansion, arising from the alignment of the optical axes of different modules (such as the test mass, optical bench, telescope, etc.), is one of the most dominant [8]. To mitigate this issue, the LISA team has proposed the use of a dedicated beam alignment mechanism (BAM) to adjust the optical alignment and reduce TTL coupling [2, 9]. The BAM was designed to suppress the TTL coupling coefficient of the scientific interferometer from 8.5 mm/rad to 2.3 mm/rad [9]. In TianQin mission, the interstellar displacement sensitivity requirement is higher, the TTL suppression requirement is higher, and the technical challenge is greater [10]. Based on the budget for the TTL coupling noise in TianQin mission, we initially set the compensation range at 0.5 mm, with a compensation precision of 1 µm.

Currently, the BAM is in its conceptual design phase, and comprehensive theoretical analyses or experimental validations of its performance are still lacking. The most significant challenge in implementing BAM lies in achieving precise two-dimensional lateral position adjustment of an Optical axis while maintaining its constant optical path length. This necessitates the ability to make millimeter-scale adjustments with micron-level precision, a requirement that pushes the limits of current optical and mechanical design. Furthermore, the mechanism must operate in the harsh environment of space, where thermal fluctuations and mechanical stresses add further complexity to maintaining alignment.

In this study, we investigate the application of a BAM as a potential solution for mitigating first-order TTL noise. The BAM employs parallel plates to dynamically adjust and correct the beam path. By fine-tuning these components, we aim to minimize transverse displacement and thereby reduce first-order TTL coupling.

The paper is organized as follows. Section 2 provides a theoretical analysis of effects associated with BAM. Numerical simulations were also performed to calculate the corresponding outcomes. Section 3 details experiments involving CCD(Charge-Coupled Device) testing to investigate the compensation range of BAM. Section 4 describes the design of a dual-beam interferometry apparatus to validate BAM’s suppression effect on first-order TTL coupling. Finally, Section 5 contains the conclusions and discussion.

Theory model

In the space gravitational wave interferometer system, the BAM employs a dual glass plate design to maintain a constant optical path length. A laser beam passes obliquely through the surface parallel plates, and by controlling the rotation angle of the two plates, the lateral position of the optical axis is adjusted. Additionally, to enable arbitrary adjustments of the optical axis position within a two-dimensional plane, each plate is designed to operate independently.

Ideal model

The schematic of the BAM is shown in Figure 1. The target laser beam passes through two surface parallel plates at an oblique angle, resulting in a lateral displacement of the optical axis. In this simplified model, the glass surfaces are parallel, and the rotation axis aligns with the incident optical axis. Therefore, the exiting optical axis is parallel and symmetric to the incident optical axis. For the first plate, the incident beam has

Figure 1. Optical schematic of the BAM, consisting of two independently inclined plates that adjust the laser beam’s lateral position.

thickness d1d_1 and refractive index n1n_1 at an incidence angle of θ1\theta_1. The lateral displacement of the optical axis, h⃗1\vec{h}_1, is given by:

h1=d1sin⁡θ1(1−cos⁡θ1n12−sin⁡2θ1).(1)h_1 = d_1 \sin\theta_1 \left(1 - \frac{\cos\theta_1}{\sqrt{n_1^2 - \sin^2 \theta_1}}\right). \tag*{(1)}

Figure 2 illustrates the relationship between lateral displacement and incidence angle θ\theta. In the range of 0∘0^\circ to 10∘10^\circ, lateral displacement increases approximately linearly. By adjusting the thickness of the plate and the angle of incidence, the BAM’s compensation range can be finely controlled. This allows for precise lateral adjustments of the optical axis, essential for space-based gravitational wave detection missions.

Relationship between the lateral displacement $h_1$ and the incidence angle $\theta_1$

Figure 2. Relationship between the lateral displacement h1h_1 and the incidence angle θ1\theta_1.

In the xx-OO-zz plane, as shown in Figure 1 and 3, both the compensation direction, defined as the angle φ1′\varphi'_1 between the refracted beam and the −z-z axis, and the rotation angle φ\varphi of plate, which is the angle between the normal vector of the plate surface and the zz axis, are projected within this plane.

As the plate rotates around the optical axis, the lateral displacement amplitude remains constant, while its direction rotates by the same angle, satisfying:

φ1′=φ1.(2)\varphi'_1 = \varphi_1. \tag*{(2)}

As a result, the position of the exiting optical axis traces a circular trajectory of radius h1h_1 around the incident optical axis. In space-based gravitational wave detection, the optical-axis compensation must be adjusted in two lateral degrees of freedom. Thus, we need a second plate.

In a new coordinate system x′−O−z′x'-O-z', similar to the first plate, the lateral displacement of the optical axis and compensate angle are given by:

h2=d2sin⁡θ2(1−cos⁡θ2n22−sin⁡2θ2)(3)h_2 = d_2 \sin\theta_2 \left(1-\frac{\cos\theta_2}{\sqrt{n_2^2-\sin^2\theta_2}}\right) \tag*{(3)}
φ2′=φ2.(4)\varphi'_2 = \varphi_2. \tag*{(4)}

The total lateral displacement of the optical axis hh is the sum of the lateral displacements produced by the dual plates, given by:

h⃗=h⃗1+h⃗2.(5)\vec{h}=\vec{h}_1+\vec{h}_2. \tag*{(5)}

By adjusting the parameters d1d_1, d2d_2, n1n_1, n2n_2, θ1\theta_1 and θ2\theta_2 to ensure h1=h2h_1=h_2, the position of the exiting optical axis of the BAM resides within a circle centered at point OO with a radius of 2h12h_1, as shown in Figure 3. Assuming ideal conditions with d1=d2=3d_1=d_2=3 mm, n1=n2=1.45n_1=n_2=1.45, and θ1=θ2=8.5∘\theta_1=\theta_2=8.5^\circ, the resulting compensation radius hh is about 280 μ\mum.

Figure 3. Compensation coverage of the BAM. h⃗1\vec{h}_1 represents the compensation position of the first plate, and O′O' is the endpoint of h⃗1\vec{h}_1. This vector can rotate as an angle φ1\varphi_1 within the xx-OO-zz plane around point OO as the plate rotates, forming a compensation range that is a circle with center OO and radius h1h_1. Similarly, h⃗2\vec{h}_2 is the compensation position of the second plate, forming a circular compensation range with center O′O' and radius h2h_2. When the two plates are combined, the overall compensation position is denoted as h⃗\vec{h}. Since both plates can rotate independently, the final compensation range forms an annulus centered at OO, with radii ranging from ∣h1−h2∣\lvert h_1-h_2\rvert to ∣h1+h2∣\lvert h_1+h_2\rvert.

Error analysis

Space-based gravitational wave detection requires BAM to achieve sub-millimeter compensation and alignment precision at the micron level for position and the microradian level for pointing. Practical error sources must be considered. Two main non-negligible factors affect BAM optical axis compensation. First, misalignment between the rotation axis and the incident optical axis alters the compensated outgoing beam. Second, non-parallel plate surfaces misalign the incident and exiting beams. The following sections provide a detailed modeling and analysis of these errors. For simplicity, we assume sufficiently flat glass surfaces to minimize wavefront distortions.

Axis misalignment

In cases where the rotation axis is misaligned by an angle δθ\delta\theta relative to the incident optical axis, as shown in Figure 4, the compensation behavior of the beam is altered. A coordinate system is defined with the point of incidence OO as the origin, and the incident beam propagating along the yy axis.

Figure 4. Axis Misalignment: The plate’s rotation axis is misaligned by an angle δθ\delta\theta relative to the beam axis.

When the plate pane rotates around the axis of rotation, the angle of incidence will change accordingly:

θ(φ)=arccos⁡n⃗y′(6)\theta(\varphi)=\arccos\vec{n}'_{y} \tag*{(6)}

More math detail can be find in Appendix § 8.§ 1. Since the surfaces of the plate remain parallel, θ(φ)\theta(\varphi) affects both the magnitude and direction of the optical axis compensation as follows:

{h′(φ)=dsin⁡θ(1−cos⁡θn2−sin⁡2θ)φ′=arctan⁡nx′nz′(7)\begin{cases} h'(\varphi)=d\sin\theta\left(1-\frac{\cos\theta}{\sqrt{n^{2}-\sin^{2}\theta}}\right) \\ \varphi'=\arctan\frac{n'_x}{n'_z} \tag*{(7)} \end{cases}

Figure 5 show the simulation results of the compensation angle and radius fluctuate as the rotation angle φ\varphi increases, with the magnitude of these fluctuations growing as the misalignment angle increases. For small misalignment angles, the compensation range remains nearly circular. However, as the misalignment angles increase, the center of the circular compensation range shifts along the zz-axis and xx-axis, respectively. This effect causes lateral shifts and compression of the compensation range, which results in beam misalignment. Linear regression shows a relationship between the compensation centroid offset Δxc\Delta x_c and the axis-misalignment angle δθ\delta\theta, with a slope of 967.29 μm/rad\mu\mathrm{m}/\mathrm{rad}. Compression, measured by the radial deviation rr from the fitted center, fluctuates by ≈0.05 μm\approx0.05\,\mu\mathrm{m} at δθ=1∘\delta\theta=1^\circ, making it negligible compared to lateral displacement under these conditions. Given the specified compensation accuracy of 1 μm\mu\mathrm{m}, our analysis suggests that the critical axis-misalignment threshold should be constrained to δθ<1 mrad\delta\theta<1\,\mathrm{mrad} to ensure optimal beam alignment.

Simulation of the compensation range with axis misalignment

Figure 5. Simulation of the compensation range with axis misalignment. Asterisks indicate the fitted centers of the corresponding compensation ranges.

Surface parallelism error

The second factor affecting beam alignment is the non-parallelism of the plate surfaces, as illustrated in Figure 6. In this scenario, the plate thickness is defined as the distance between the two surfaces. The parallelism error, denoted as α\alpha, represents the angle between the surfaces, which introduces a misalignment between the incident and exiting beams, denoted by β\beta.

Figure 6. The surface parallelism error caused by the plate’s wedge angle α\alpha, leading to a beam-axis tilt β\beta.

When the plate rotates, the angle of incidence θ0\theta_0 is maintained, signifying that the compensation radius remains unchanged. At the same time, the constant angle between the normal vector of the plate, n⃗plateB\vec{n}_{\mathrm{plateB}}, and the y-axis results in a stable beam deflection angle β\beta induced by the plate.

With the mathematical detail in Appendix § 8.§ 2, the compensation value and angle are calculated as

{h′=dsin⁡θ(1−cos⁡θ0n2−sin⁡2θ0),φ′=φb⃗exit=M(n⃗plateB′)⋅M(n⃗plateA′)⋅y⃗(8)\begin{cases} h' = d\sin\theta\left(1-\frac{\cos\theta_0}{\sqrt{n^2-\sin^2\theta_0}}\right),\\ \varphi' = \varphi\\ \vec{b}_{\mathrm{exit}} = \mathrm{M}(\vec{n}'_{\mathrm{plateB}})\cdot\mathrm{M}(\vec{n}'_{\mathrm{plateA}})\cdot\vec{y} \tag*{(8)} \end{cases}

where b⃗exit\vec{b}_{\mathrm{exit}} is the direction vector of the exiting beam. And beam deflection angle β\beta can be express as

β=arcsin⁡(sin⁡θ0cos⁡α+n2−sin⁡2θ0⋅sin⁡α)−θ0−α≈(n2−sin⁡2θ0cos⁡θ0−1)α(9)\beta= \arcsin\left(\sin\theta_{0}\cos\alpha+ \sqrt{n^{2}-\sin^{2}\theta_{0}}\cdot\sin\alpha\right)-\theta_{0}-\alpha \approx\left(\frac{\sqrt{n^{2}-\sin^{2}\theta_{0}}}{\cos\theta_{0}}-1\right)\alpha \tag*{(9)}

The surface parallelism error, as illustrated in Figure 6, arises from the wedge angle of the plate. When the plate is fixed, the wedge angle is characterized by the normal vector of surface B, represented as n⃗plateB\vec{n}_{\mathrm{plateB}}. The projection of n⃗plateB\vec{n}_{\mathrm{plateB}} onto the xx-OO-zz plane can vary in any direction. Therefore, the surface parallelism error depends on both the wedge angle’s magnitude and the orientation of n⃗plateB\vec{n}_{\mathrm{plateB}}. The wedge angle determines the amount of tilt introduced to the optical axis, while the orientation of n⃗plateB\vec{n}_{\mathrm{plateB}} defines the direction of the tilt. In the simulation, the wedge angle is set to ±30′′\pm30^{\prime\prime}, and n⃗plateB\vec{n}_{\mathrm{plateB}} is positioned within the xx-OO-zz plane.

The simulation results in Figure 7 show that surface parallelism errors of the plate slices induce an additional tilt in the outgoing beam axis, with the tilt direction determined by the orientation of n⃗plateB\vec{n}_{\mathrm{plateB}}. In space-based gravitational wave detection, the BAM is primarily used to compensate for pupil misalignments between the telescope and the optical interferometer bench. Any additional angular deviation in the outgoing beam axis reduces the interference contrast and increases TTL coupling errors. Given the TianQin specifications, the additional angular offset caused by the BAM should not exceed 30 μrad30\,\mu\mathrm{rad}.

Simulation of the compensation range with surface parallelism error

Figure 7. Simulation of the compensation range with surface parallelism error. solid lines and dashed lines represent opposite directions of the plate wedge angle.

Beam alignment tests

Optical setup

The optical setup for beam alignment tests has been meticulously designed to evaluate the performance and precision of the BAM. Schematic diagram of the BAM experiment is shown in Figure 8. Central to this experiment are two identical K9 plates measuring 10 mm×10 mm×3 mm10\ \mathrm{mm} \times10\ \mathrm{mm} \times3\ \mathrm{mm}. These plates are mounted at an angle on high-precision motorized rotation motor, which provide angular control with a resolution of about 0.05∘0.05^{\circ}. This level of precision enables fine adjustments to the beam path, essential for achieving accurate alignment.

Schematic diagram of the BAM for experimental validation

Figure 8. Schematic diagram of the BAM for experimental validation. The Gauss beam, originating from the collimator on the left, sequentially traverses through dual plates positioned on a rotation motor, ultimately being detected by the CCDCharge-Coupled Device. The rotational axis is adjusted using an attitudes adjustment stage beneath the rotation motor to align as closely as possible with the beam axis. When the two rotation motor move independently, the beam experiences lateral displacement within a plane constrained by a annulus range.

Initially, the plates are set at an approximate angle of 8.5∘8.5^{\circ} relative to the incident beam, facilitating effective control of beam displacement during rotation. Since the thickness of each plate cannot be perfectly uniform, it is necessary to adjust the incident angle to ensure that the compensation radii of the two plates become approximately equal. We designed the flange shown in Figure 9 to connect the plates to the rotation motor; the flange is secured to the rotation motor using retaining rings. Initially, the plates are clamped by the inherent stress of the flange, and after adjusting the incident angle, they are bonded to the flange using epoxy resin.

Schematic diagram of the flange connecting the plates to the rotation motor

Figure 9. Schematic diagram of the flange connecting the plates to the rotation motor. The flange is secured to the rotation motor using retaining rings. Initially, the plates are clamped by the inherent stress of the flange and are later bonded to the flange with epoxy resin after adjusting the incident angle.

To adjust the compensation radii, it is necessary to align the rotation axis with the incident light axis. First, we adjust the beam to be as parallel as possible to the optical table and to be vertically incident on the CCD, using the CCD to detect the center position of the beam as a reference point. Next, we place a plate mounted on the rotation motor between the CCD and the collimator, causing the center of the beam spot on the CCD to shift accordingly. According to our simulation results, if the rotation axis and the incident light axis are not aligned, the final compensation range will be offset as a whole. This offset manifests as a displacement between the center of the compensation range and the reference point.

Therefore, we rotate the plate through a full revolution, collect the corresponding beam center positions on the CCD, and calculate the center of the compensation range by fitting these positions. Using the attitude adjustment stage, we adjust the rotation axis of the rotation motor until the fitted center coincides with the reference point. This alignment indicates that the rotation axis and the incident light axis are now properly aligned.

Subsequently, the relative angle between the plate and the flange can be adjusted to fine-tune the compensation radius. After each adjustment, the plate is rotated once, and the compensation radius is determined by fitting the data from the CCD.

However, to achieve the precise vertical incidence of the beam on the CCD, we manually adjust the CCD position. This ensures the beam is as perpendicular as possible to the surface of the CCD. Once this adjustment is made, the plate is rotated through a full revolution, and we collect the beam center data corresponding to each position on the CCD. To account for any distortion due to the rotation, we apply a projection transformation to the data. This transformation corrects the data to be as circular as possible, and the projection coefficient corresponding to the CCD position at this time is calculated. All subsequent data processing will then be adjusted by multiplying the projection coefficient, ensuring accurate results that account for any deviations in the CCD’s orientation.

To achieve the precise vertical incidence of the beam on the CCD, we manually adjusted the CCD position to approach perpendicular alignment (though perfect verticality cannot be guaranteed). Following this coarse alignment, the plate was rotated through a complete revolution while recording centroid positions of the beam center on the CCD.

Due to beam path rotation about the plate’s axis and potential residual CCD tilt, the collected coordinates formed elliptical distributions rather than perfect circles. We therefore applied an affine transformation to rectificate the coordinates:

x′=kxxx+kxzy,z′=kyzx+kzzy(10)x' = k_{xx}x + k_{xz}y,\qquad z' = k_{yz}x + k_{zz}y \tag*{(10)}

where the transformation coefficients kijk_{ij} were determined through least-squares fitting to minimize deviations from circular symmetry. These coefficients inherently encoding the CCD’s instantaneous spatial orientation were subsequently applied as multiplicative corrections to all experimental data during post-processing.

The two BAM components are arranged sequentially in the optical path following a laser collimator, with a CCD positioned downstream of the second BAM component. This configuration allows for high-precision monitoring of the beam position, thereby enabling accurate measurement of beam displacement resulting from the combined effects of the BAM.

System control and data acquisition are managed by two specialized programs, which interface with the rotation mounts and CCD camera respectively. The software employs image processing algorithms to determine the centroid position of the beam spot on the CCD sensor, allowing for precise tracking of beam displacement relative to the pane rotation angles. The centroid position (xc,zc)(x_c, z_c) is calculated using the weighted average method:

xc=∑i∑jxijIij∑i∑jIij,zc=∑i∑jzijIij∑i∑jIij(11)x_c = \frac{\sum_i \sum_j x_{ij} I_{ij}}{\sum_i \sum_j I_{ij}}, \qquad z_c = \frac{\sum_i \sum_j z_{ij} I_{ij}}{\sum_i \sum_j I_{ij}} \tag*{(11)}

where xijx_{ij} and zijz_{ij} are the coordinates of pixel (i,j)(i,j), and IijI_{ij} is the intensity of that pixel. This method provides a robust and accurate determination of the beam position, accounting for variations in beam shape and intensity distribution.

Test results

To comprehensively assess the performance of the Beam Alignment Mechanism (BAM), we structured our experiments into three distinct parts: (1) evaluating the effects of axis misalignment using a single plate, (2) analyzing the impacts of surface parallelism using a single plate, and (3) investigating the combined effects of axis alignment with dual plates. Each experiment tracks the beam center across a full rotation of the plates, referred to as the compensation range.

In the initial experiments, we isolated the effects of individual components by removing one of the plates from the setup. This adjustment allowed for a clearer understanding of how each factor contributes to beam alignment.

The first experiment focused on the axis misalignment effect. We minimized the distance between the CCD camera and the plate to 35 mm to mitigate effect caused by surface non-parallelism. The results of this setup are shown in Figure 10, where the blue solid line represents the initial manual installation with lateral shifts in the compensation range of 28.6 µm, whereas the red solid line demonstrates the improved alignment achieved through the attitude adjustment stage with a reduced offset of 13.0 µm. The optimal alignment result (gray curve) exhibits a residual offset of merely 1.0 µm, satisfying the system’s precision requirements. The fitted centers of the corresponding compensation ranges are denoted by asterisks.

Compensation ranges with axis misalignment for a single plate, showing misaligned 0.042°, 0.55°, and 1.20° curves

Figure 10. Compensation range with axis misalignment for a single plate. The gray line represents results with axis alignment, while the blue and red lines show results with both pitch and yaw angles of 0.55∘0.55^\circ and 1.10∘1.10^\circ, respectively. Asterisks indicate the fitted centers of the corresponding compensation ranges.

Furthermore, angular misalignments of the attitude adjustment stage based on autocollimator calibration was about 1.2∘1.2^\circ, 0.55∘0.55^\circ, and 0.042∘0.042^\circ in the three tests, respectively. The linear correlation coefficient between lateral offset and angular misalignment was determined to be 975.7 μm/rad975.7\,\mathrm{\mu m/rad}, in agreement with the theoretical model presented in section 2.2.1.

Next, we examined the influence of surface parallelism error on beam alignment. The rotation axis was pre-aligned to the optical axis, allowing us to analyze the tilt induced in the exiting beam due to misalignment between the front and rear surfaces of the plate. The experimental procedure was as follows: First, the CCD was fixed in a set position so that the collimated laser beam from the collimator directly impinged on it, and the beam center was recorded. Next, the plate was inserted while ensuring that its distance from the CCD was maintained at 35 mm. Using the method described in § 3.1, the plate’s rotation axis was aligned with the optical axis. The plate was then rotated a full 360° and the corresponding beam center on the CCD was recorded. Subsequently, the CCD was moved to a distance of 251 mm from the plate, while the plate’s rotation axis keeping aligned with the optical axis, and the plate was rotated one complete turn again with the beam center being recorded. Finally, with the CCD held fixed and the plate removed, the center position of the beam from the collimator was recorded.

Figure 11 shows the compensation ranges for different plates and CCDs at distinct positions. According to the equation

Compensation ranges with surface parallelism error for a single plate, showing plate 1 and plate 2 at CCD distances of 35 mm and 251 mm

Figure 11. Compensation range with surface parallelism error for a single plate. Red and blue lines represent two different plates, with solid and dashed lines indicating distances of 35 mm and 251 mm between the CCD camera and the plate, respectively.

β=arcsin⁡(ΔrΔL),(12)\beta= \arcsin\left(\frac{\Delta r}{\Delta L}\right), \tag*{(12)}

where ΔL\Delta L represents the distance between two CCD measurements and Δr\Delta r denotes the difference in compensation radii, the non-parallelism errors of the plate1_1 and plate2_2 panes are calculated to be 96.4 μ\murad and 54.6 μ\murad, respectively. In subsequent experiments, we will select plate with smaller non-parallelism errors to conduct testing on the BAM prototype.

In the third experiment, we explored the combined effects of axis alignment using two rotating plates. The setup, depicted in Figure 12, was designed to create a spiral-like displacement pattern. As the two plates rotated at different angular velocities, the compensation range accumulated, forming an area constrained within a circular path. This design allowed us to visualize the cumulative impact of both plates on beam alignment.

Compensation range with axis alignment for dual plates

Figure 12. Compensation range with axis alignment for dual plates. The setup rotates two plates at different angular velocities over a period, creating a spiral-like pattern. Over time, the compensation range accumulates, forming a circular area with a diameter of about 500 μ\mum.

TTL tests

In previous sections, we have established the compensation range of the BAM structure for both single and dual plate configurations, particularly under the influence of axis and surface parallelism errors. This section delves into the application of BAM for inducing lateral displacement in interferometry to suppress first-order tilt-to-length (TTL) coupling.

Optical setup

The experimental setup is based on a compact heterodyne interferometer, designed for high-precision measurement and simplified system architecture [11]. The interferometer is assembled using UV bonding technology, which enhances mechanical stability and ensures long-term alignment precision [12, 13]. The optical schematic of TTL coupling suppressing by BAM is illustrated in Figure 13. The system utilizes two heterodyne beams, differing by 10 kHz in frequency. These beams are introduced through collimators and directed through distinct optical paths.

Optical schematic of TTL coupling suppression using the BAM

Figure 13. The optical schematic of TTL coupling suppression using the BAM. The setup incorporates critical components: FS (fiber splitter), AOM (acousto-optic modulators), FC (fiber collimator), BS (beam splitter), and PD (photodetector). The BAM introduces controlled lateral displacement to align the beam with the target mirror, effectively minimizing first-order TTL coupling errors in the interferometric measurement.

One beam is reflected off a stable reference mirror before being combined with the second beam at beam splitter BS1_1, producing a reference signal that is detected by photodetector PDr_r. The second beam traverses the BAM, undergoes reflection from a target mirror, and retraces its path back through the BAM. Finally, the beams recombine at beam splitter BS2_2, with the resulting interference signal captured by photodetector PDm_m.

The primary factor influencing first-order TTL coupling is the lateral displacement between the beam’s reflection point on the target mirror and the mirror’s rotation axis. A 6-axis Hexapod (PI-H811) is employed to control and fine-tune the target mirror’s rotation axis while actively inducing sinusoidal angular jitter with a amplitude of 100 µm and a frequency of 1 Hz. The BAM allows precise adjustments to the beam position on the target mirror, effectively compensating for first-order TTL coupling errors and enhancing the overall measurement accuracy.

Test results

The results of the TTL tests are illustrated in Figure 14, which clearly shows the effectiveness of the BAM in reducing first-order TTL coupling errors. Initially, the TTL coupling coefficient was measured at approximately 300 μm/rad300\,\mu\mathrm{m}/\mathrm{rad}. As the BAM was employed to adjust and align the beam axis, a gradual decrease in this coupling error was observed. By meticulously fine-tuning the lateral displacement of the beam axis, the coupling coefficient was ultimately reduced to an impressive 5 μm/rad5\,\mu\mathrm{m}/\mathrm{rad}. Further first-order TTL coupling suppression is limited by the optical axis tuning accuracy of the BAM and the displacement measurement noise floor of the interferometer bench.

TTL coupling test results showing displacement versus angle for different TTL coupling coefficients

Figure 14. TTL coupling test results, showing the TTL coupling curve with angle. The marker represents the experimental data, and the line represents the fitting curve.

This significant reduction underscores the BAM’s potential to enhance measurement precision in interferometric systems, particularly in the context of gravitational wave detection. The experimental data aligns well with theoretical predictions, demonstrating that the BAM can effectively manage the adverse effects of misalignment and surface errors. Such capabilities are crucial for improving the performance of gravitational wave detectors, where minimizing noise is essential for accurate measurements. This significant reduction underscores the BAM’s potential to enhance measurement precision in interferometric systems, particularly in the context of gravitational wave detection. The experimental data aligns well with theoretical predictions, demonstrating that the BAM can effectively manage the adverse effects of first order TTL induced through optical component misalignments. Such capabilities are crucial for improving the performance of gravitational wave detectors, where minimizing noise is essential for accurate measurements.

Discussion and conclusion

This study explored the Beam Alignment Mechanism’s (BAM) ability to mitigate tilt-to-length (TTL) coupling noise in gravitational wave detectors. The experimental results affirm that BAM significantly compensates for lateral displacement errors, effectively aligning the optical axis and reducing TTL noise. However, challenges remain due to misalignments that can introduce additional tilts, potentially affecting suppression efficiency. While current configurations show promise, further optimization is necessary. In conclusion, BAM represents a substantial advancement in addressing TTL noise, enhancing the precision of interferometric measurements. Ongoing research into alignment techniques and adaptive control algorithms will be vital in refining BAM’s effectiveness. By overcoming existing limitations, BAM can play a pivotal role in the space generation of gravitational wave detectors.

Data availability statement

The data cannot be made publicly available upon publication because no suitable repository exists for hosting data in this field of study. The data that support the findings of this study are available upon reasonable request from the authors.

Acknowledgments

We gratefully thank Prof. Jun Luo for the helpful suggestion. This work was supported by the National Natural Science Foundation of China (Grant Nos. 12105375) and the National Key Research and Development Program of China (Grant Nos. 2023YFC2205800).

Error analysis

Axis misalignment

As shown in Figure 4, point OO serves as both the point of incidence and the origin of the coordinate system. The unit vectors x⃗\vec{x}, y⃗\vec{y}, and z⃗\vec{z} represent the axes of this coordinate system. The rotation axis is defined by its direction (n⃗axis)(\vec{n}_{\mathrm{axis}}) and a point AA on it, such as:

A=(xA,yA,zA)n⃗axis=(nx,ny,nz)T,(13)\begin{aligned} A &= (x_A,y_A,z_A) \\ \vec{n}_{\mathrm{axis}} &= (n_x,n_y,n_z)^{\mathrm{T}}, \tag*{(13)} \end{aligned}

which satisfies the conditions:

∣n⃗axis∣=1n⃗axis⋅y⃗∣n⃗axis∣∣y⃗∣=cos⁡δθ.(14)\begin{aligned} \lvert\vec{n}_{\mathrm{axis}}\rvert&= 1 \\ \frac{\vec{n}_{\mathrm{axis}}\cdot\vec{y}}{\lvert\vec{n}_{\mathrm{axis}}\rvert\lvert\vec{y}\rvert} &= \cos\delta\theta. \tag*{(14)} \end{aligned}

Follow the Rodrigues’ rotation formula, the rotation matrix R(n⃗axis,φ)\mathbf{R}(\vec{n}_{\mathrm{axis}},\varphi) for an angle φ\varphi around the rotation axis is:

R=I+sin⁡φK+(1−cos⁡φ)K2,(15)\mathbf{R}=\mathbf{I}+\sin\varphi\mathbf{K}+(1-\cos\varphi)\mathbf{K}^{2}, \tag*{(15)}

where I\mathbf{I} is the identity matrix and K\mathbf{K} is the cross-product matrix of n⃗axis\vec{n}_{\mathrm{axis}}:

K=(0−nznynz0−nx−nynx0).(16)\mathbf{K}= \begin{pmatrix} 0 & -n_z & n_y \\ n_z & 0 & -n_x \\ -n_y & n_x & 0 \end{pmatrix}. \tag*{(16)}

Initially, the normal vector of the plate surface lies in the yy-OO-zz plane as

n⃗plate=(0,cos⁡θ0,sin⁡θ0)T.(17)\vec{n}_{\mathrm{plate}}=(0,\cos\theta_0,\sin\theta_0)^{\mathrm{T}}. \tag*{(17)}

After rotation, the new normal vector is given by:

n⃗plate′=(xyz)+R(n⃗axis,φ)⋅(n⃗plate−(xyz))=(nx′,ny′,nz′)T,(18)\vec{n}'_{\mathrm{plate}}= \begin{pmatrix} x\\ y\\ z \end{pmatrix} +\mathbf{R}(\vec{n}_{\mathrm{axis}},\varphi)\cdot \left(\vec{n}_{\mathrm{plate}}- \begin{pmatrix} x\\ y\\ z \end{pmatrix}\right) =(n'_x,n'_y,n'_z)^{\mathrm{T}}, \tag*{(18)}

where

nx′=(1−cos⁡φ)nx(cos⁡θ0ny+sin⁡θ0nz)+sin⁡φ(sin⁡θ0ny−cos⁡θ0nz)ny′=cos⁡θ0(1−(1−cos⁡φ)(nx2+nz2))+sin⁡θ0((1−cos⁡φ)nynz−sin⁡φnx)nz′=cos⁡θ0((1−cos⁡φ)nynz+sin⁡φnx)+sin⁡θ0(1−(1−cos⁡φ)(nx2+ny2))(19)\begin{aligned} n'_x={}&(1-\cos\varphi)n_x(\cos\theta_0n_y+\sin\theta_0n_z)+\sin\varphi(\sin\theta_0n_y-\cos\theta_0n_z) \\ n'_y={}&\cos\theta_0\left(1-(1-\cos\varphi)(n_x^2+n_z^2)\right)+\sin\theta_0\left((1-\cos\varphi)n_yn_z-\sin\varphi n_x\right) \\ n'_z={}&\cos\theta_0\left((1-\cos\varphi)n_yn_z+\sin\varphi n_x\right)+\sin\theta_0\left(1-(1-\cos\varphi)(n_x^2+n_y^2)\right) \tag*{(19)} \end{aligned}

Replacing n⃗plate\vec{n}_{\mathrm{plate}} with n⃗plate′\vec{n}'_{\mathrm{plate}}, the incident angle θ\theta can be expressed as a function of the rotation angle φ\varphi:

θ(φ)=arccos⁡(n⃗plate′⋅y⃗∥n⃗plate′∥∥y⃗∥)=arccos⁡ny′(20)\theta(\varphi)=\arccos\left(\frac{\vec{n}'_{\mathrm{plate}}\cdot\vec{y}}{\lVert\vec{n}'_{\mathrm{plate}}\rVert\lVert\vec{y}\rVert}\right)=\arccos n'_{y} \tag*{(20)}

Surface parallelism error

As shown in Figure 8, the normal vector of the front surface is defined as:

n⃗plateA=(0,cos⁡θ,sin⁡θ)T.(21)\vec{n}_{\mathrm{plateA}}=(0,\cos\theta,\sin\theta)^{\mathrm{T}}. \tag*{(21)}

The normal vector of the second surface is given by:

n⃗plateB=R(n⃗plateA,ϕ)⋅(0,cos⁡(θ−α),sin⁡(θ−α))T(22)\vec{n}_{\mathrm{plateB}}=\mathbf{R}(\vec{n}_{\mathrm{plateA}},\phi)\cdot(0,\cos(\theta-\alpha),\sin(\theta-\alpha))^{\mathrm{T}} \tag*{(22)}
(−sin⁡ϕsin⁡θcos⁡θ1+sin⁡ϕcos⁡θsin⁡θ1(1−(1−cos⁡ϕ)sin⁡2θ)cos⁡θ1+(1−cos⁡ϕ)sin⁡θcos⁡θsin⁡θ1(1−cos⁡ϕ)sin⁡θcos⁡θcos⁡θ1+(1−(1−cos⁡ϕ)cos⁡2θ)sin⁡θ1)(23)\begin{pmatrix} -\sin\phi\sin\theta\cos\theta_{1}+\sin\phi\cos\theta\sin\theta_{1}\\ (1-(1-\cos\phi)\sin^{2}\theta)\cos\theta_{1}+(1-\cos\phi)\sin\theta\cos\theta\sin\theta_{1}\\ (1-\cos\phi)\sin\theta\cos\theta\cos\theta_{1}+(1-(1-\cos\phi)\cos^{2}\theta)\sin\theta_{1} \tag*{(23)} \end{pmatrix}

where θ1=θ−α\theta_{1}=\theta-\alpha and ϕ\phi is the angle between the projected vector of n⃗plateA\vec{n}_{\mathrm{plateA}} in the xx-OO-zz plane and the zz axis.

According to the equation (A.6), the two surfaces normal vector n⃗plate0′\vec{n}'_{\mathrm{plate0}} after rotation around the rotation axis with plate can be expressed as:

n⃗plateA′=R(y⃗,φ)⋅n⃗plateA=(sin⁡φsin⁡θcos⁡θcos⁡φsin⁡θ),(24)\vec{n}'_{\mathrm{plateA}}=\mathbf{R}(\vec{y},\varphi)\cdot\vec{n}_{\mathrm{plateA}}= \begin{pmatrix} \sin\varphi\sin\theta\\ \cos\theta\\ \cos\varphi\sin\theta \end{pmatrix}, \tag*{(24)}
n⃗plateB′=R(y⃗,φ)⋅n⃗plateB(25)\vec{n}'_{\mathrm{plateB}}=\mathbf{R}(\vec{y},\varphi)\cdot\vec{n}_{\mathrm{plateB}} \tag*{(25)}

The direction of the exiting beam after refraction can be calculated using Snell’s law, leading to the compensation value and angle:

b⃗out=b⃗inn+(cos⁡θn−1−1−cos⁡2θn2)n⃗plate=M(n⃗plate)⋅b⃗in,(26)\vec{b}_{\mathrm{out}}=\frac{\vec{b}_{\mathrm{in}}}{n}+\left(\frac{\cos\theta}{n}-\sqrt{1-\frac{1-\cos^{2}\theta}{n^{2}}}\right)\vec{n}_{\mathrm{plate}}=\mathbf{M}(\vec{n}_{\mathrm{plate}})\cdot\vec{b}_{\mathrm{in}}, \tag*{(26)}

where b⃗in\vec{b}_{\mathrm{in}} and b⃗out\vec{b}_{\mathrm{out}} denote the incident and refracted beam vectors at a single interface, respectively, while M(n⃗plate)\mathbf{M}(\vec{n}_{\mathrm{plate}}) characterizes the directional transformation matrix induced by plate surface refraction. After the beam undergoes refraction twice—once at the front and once at the rear surface of the plate—the direction vector of the exiting light can be determined. The compensation value and angle are calculated similarly to the equation (1) and (2) as

{h′=dsin⁡θ(1−cos⁡θ0n2−sin⁡2θ0),φ′=φb⃗exit=M(n⃗plateB′)⋅M(n⃗plateA′)⋅y⃗(27)\begin{cases} h'=d\sin\theta\left(1-\dfrac{\cos\theta_{0}}{\sqrt{n^{2}-\sin^{2}\theta_{0}}}\right),\\ \varphi'=\varphi\\ \vec{b}_{\mathrm{exit}}=\mathbf{M}(\vec{n}'_{\mathrm{plateB}})\cdot\mathbf{M}(\vec{n}'_{\mathrm{plateA}})\cdot\vec{y} \tag*{(27)} \end{cases}

where bexitb_{\mathrm{exit}} is the direction vector of the exiting beam after refraction at both surfaces of the plate.

References

  1. [1]Collaboration L S et al. 2023 Physical Review X 13 041039 publisher: American Physical Society URL https://doi.org/10.1103/PhysRevX.13.041039
  2. [2]Colpi M et al. 2023 LISA Definition Study Report arXiv:2402.07571 [astro-ph, physics:gr-qc] URL https://doi.org/10.48550/arXiv.2402.07571
  3. [3]Luo J et al. 2016 Classical and Quantum Gravity 33 035010 ISSN 0264-9381 publisher: IOP Publishing URL https://doi.org/10.1088/0264-9381/33/3/035010
  4. [4]Mei J et al. 2021 Progress of Theoretical and Experimental Physics 2021 05A107 ISSN 2050-3911 URL https://doi.org/10.1093/ptep/ptaa114
  5. [5]Hu W R and Wu Y L 2017 National Science Review 4 685–686 ISSN 2095-5138 URL https://doi.org/10.1093/nsr/nwx116
  6. [6]Hartig M S, Schuster S and Wanner G 2022 Journal of Optics 24 065601 ISSN 2040-8978, 2040-8986 URL https://doi.org/10.1088/2040-8986/ac675e
  7. [7]Hartig M S, Schuster S, Heinzel G and Wanner G 2023 Journal of Optics 25 055601 ISSN 2040-8978, 2040-8986 URL https://doi.org/10.1088/2040-8986/acc3ac
  8. [8]Paczkowski S, Giusteri R, Heinson M, Karnesis N, Fitzsimons E D, Wanner G and Heinzel G 2022 Physical Review D 106 042005 ISSN 2470-0010, 2470-0029 URL https://doi.org/10.1103/PhysRevD.106.042005
  9. [9]Brzozowski W et al. 2022 The LISA optical bench: an overview and engineering challenges Space Telescopes and Instrumentation 2022: Optical, Infrared, and Millimeter Wave vol 12180 (SPIE) pp 237–253 URL https://doi.org/10.1117/12.2627465
  10. [10]Gong Y, Luo J and Wang B 2021 Nature Astronomy 5 881–889 ISSN 2397-3366 publisher: Nature Publishing Group URL https://doi.org/10.1038/s41550-021-01480-3
  11. [11]Yan H, Mao Q, Xie S, Liu S, Luo J and Yeh H C 2020 Optics Letters 45 2792–2795 ISSN 1539-4794 publisher: Optica Publishing Group URL https://doi.org/10.1364/OL.392856
  12. [12]Lin X, Yan H, Miao H X, Qiu P, Liang Y R, Yeh H C and Zhou Z B 2024 Optics Express 32 37167–37181 ISSN 1094-4087 publisher: Optica Publishing Group URL https://doi.org/10.1364/OE.539457
  13. [13]Lin X, Yan H, Ma Y and Zhou Z 2023 Review of Scientific Instruments 94 074501 ISSN 0034-6748 URL https://doi.org/10.1063/5.0155637

Paper details

vlnc:W_d3ua23xw
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents