WorksPhysics and Astronomy
Low cross-plane thermal conductivity of -GaO thin films
Abstract
The thermal conductivities of (001) -GaO thin films deposited on -plane sapphire substrates were measured with frequency-domain thermoreflectance (FDTR). The thermal conductivity increases from 1.83 W/mK to 2.26 W/mK as the thicknesses increase from 159 nm to 689 nm. This weak thickness dependence indicates that the majority of the intrinsic phonon mean free paths are smaller than the range of investigated film thicknesses. First-principles-based calculations that include phonon-phonon and phonon-boundary scattering capture this size-dependent behavior and support our experimental observation. Temperature-dependent measurements of a 689 nm film from 293 to 400 K show a decrease in thermal conductivity with increasing temperature due to enhanced phonon-phonon scattering. A weaker temperature dependence is observed in a 159 nm film where phonon-boundary scattering becomes more prominent. At comparable film thicknesses, our measured -GaO films exhibit lower values of cross-plane thermal conductivity than the other experimentally measured GaO polymorphs. Our experimental observations are supported by prior predictions, which suggest that the low thermal conductivity of -GaO results from its complex crystal structure, which leads to increased anharmonicity and lower phonon group velocities relative to other polymorphs. Thermal management strategies, such as integration with high-thermal-conductivity substrates, may thus be required to mitigate self-heating for -GaO-based electronic devices.
Gallium oxide (GaO) is an ultra-wide bandgap (UWBG) semiconductor that occurs in four polymorphs, -, -, -, and -.[1] -GaO is the only polymorph lacking inversion symmetry, resulting in spontaneous polarization and piezoelectric behavior.[2, 3, 4] With a piezoelectric strain constant that is twice that of AlN, -GaO has the potential to be an emerging piezoelectric semiconductor for radio frequency (RF) resonators in high electron mobility transistors (HEMTs).[5] Its spontaneous polarization also leads to a high density two-dimensional electron gas (2DEG) at the -GaO/AlN interface without doping.[6] -GaO can also be stacked with -GaO to create a -GaO/-GaO heterojunction, which can be exploited for devices that rely on interfacial depletion fields to enable efficient carrier separation.[7] Although -GaO is thermodynamically metastable,[2, 4] it exhibits substantial kinetic thermal stability and typically transforms to the -phase only after annealing at approximately 700-1000 °C, enabling a large window for device fabrication and high-temperature operation.[2, 8, 9] -GaO has attracted significant interest for applications in next-generation power electronics and deep-ultraviolet photodetectors due to its ultrawide bandgap (4.8 eV) and its thermal stability.[10, 11] -GaO, with a bandgap (4.9 eV) similar to that of -GaO, has the potential to be used in similar applications. However, -GaO’s relatively low thermal conductivity (11-27 W/m·K)[13] compared to other wide bandgap semiconductors, such as GaN (210 W/m·K)[14] and AlN (320 W/m·K),[15] poses a limitation to effective thermal management in RF and power devices.
The thermal conductivities of different GaO polymorphs have been reported in the literature. Szwajkowski et al. showed size effects in the thermal conductivity of -GaO thin film, as the thermal conductivity increases from 0.3 W/m·K to 9.0 W/m·K with thickness increasing from 12 nm to 600 nm.[16] Song et al. also reported the increase in the thermal conductivity of -GaO thin films from 6.3 0.6 W/m·K to 10.8 1.2 W/m·K with thickness increasing from 164 nm to 2500 nm.[17] Our previous work has demonstrated a size dependence of -GaO thin films, which increase from 2.3 W/m·K to 3.5 0.7 W/m·K for films with thicknesses of 75 nm to 404 nm.[18] These size effects in the thermal conductivity of GaO occur because boundary scattering reduces contributions from phonons with intrinsically long mean free paths (MFPs).[19, 20] Karim et al. reports the thermal conductivity of 1.2 m thick -GaO to be 11.9 1.0 W/m·K,[21] which is the highest of all polymorphs at comparable thicknesses. Several computational studies have reported the lattice thermal conductivity of -GaO along the (001) direction, which ranges from 1 to 4 W/m·K.[22, 23, 24, 25] Xiao et al.[26] have measured the thermal conductivity of 50, 65, and 89 nm thick (001) -GaO to be 1-3 W/m·K, with a negligible size dependence. However, extensive measurements of the thermal conductivity of -GaO over a wider thickness range have not been reported in the literature.
In this paper, we report the thermal conductivity of -GaO thin films deposited on -plane sapphire substrates, where the measurements were taken along the (001) direction of the films and over film thicknesses ranging from 159 nm to 689 nm. To support our experimental results, we also employ first-principles-based calculations of the size-dependent thermal conductivity of -GaO. In addition, we report the temperature-dependent thermal conductivity of 159 nm and 689 nm -GaO films at temperatures ranging from 293 K to 400 K. The results are compared with experimentally measured thermal conductivities of other polymorphs reported previously.
Six - films with thicknesses ranging from 159 nm to 689 nm were grown on (0001) (c-sapphire) substrates at 530 °C using a vertical, low-pressure, cold-wall metal-organic chemical vapor deposition reactor. Triethylgallium (TEGa) and ultra-high purity (5N) were used as the precursors, with serving as the carrier gas for the TEGa. The TEGa bubbler was maintained at 20 °C with 45 sccm carrier gas flowing through the bubbler, resulting in a TEGa molar flow rate of 70 mol/min. The flow rate was fixed at 500 sccm, corresponding to an O/Ga (VI/III) ratio of 635. The detailed growth parameters and comprehensive film characterization have been reported in our previous publications.[2, 27]
High-resolution X-ray diffraction (HR-XRD) patterns of the as-grown films were acquired using a Panalytical X’pert Pro MPD X-ray diffractometer equipped with a four-crystal Ge (220) monochromator. As shown in Figure 1(a), only (002) and (004) - peaks are observed other than the substrate peak. Based on our previous cross-sectional transmission electron microscopy studies on a representative 700 nm thick - film grown under the same conditions, 3 monolayers of pseudomorphic - form on the c-plane sapphire substrate, followed by a 20 nm transition layer containing a mixture of and phase, with phase-pure on top of the transition layer. The ultra-thin pseudomorphic layer and the low volume fraction and poor crystallinity of the transition layer fall below the detection limit of the XRD scans.[27] The presence of such a transition layer is commonly observed in MOCVD-grown - films on c-plane sapphire;[27, 28, 29, 30, 31] these films are thus referred as nominally phase-pure. Figure 1(b) shows that the full-width-at-half-maximum of the X-ray rocking curves for these films is comparable, indicating similar crystallinity across various film thicknesses. Figure 1(c) shows the presence of in-plane rotational domains separated by 120° across, independent of film thickness. Since these rotational domains are oriented in-plane, they will not affect the out-of-plane thermal conductivity measured in this study. The presence of such in-plane rotational domains is due to the nature of 6-fold symmetry of the c-plane sapphire substrate.[9] The (001) out-of-plane epitaxial relationship between and c-sapphire is commonly observed due to the similarity of the oxygen atomic arrangement between (001) sapphire and the (001) . Both exhibit a pseudo-hexagonal lattice with a lattice mismatch of 5.7%. The reciprocal spacing maps (RSM) for the thin (159 nm), medium (341 nm), and thick (689 nm) films (see Supplementary Information, Fig. S1) show that the films are relaxed to similar states across the entire film thickness. The atomic force microscopy (AFM) images of the films are shown in Fig. S2, where the thinner film shows lower roughness than the thicker film, but all within 1.5% of the film thickness. These additional results confirm that the crystallinity, domain structure, strain relaxation and relative surface roughness remain consistent across these six films.

Figure 1. (a) HR-XRD - scans for the six - films on c-plane sapphire substrates. The black star symbol denotes the diffraction peaks from the substrates. (b) Symmetric X-ray rocking curves of the (004) reflection for the six films. (c) -scans of the {222} reflection for three representative - films. The diamond symbols in different colors represent three types of in-plane rotational domains.
The thickness-dependent and temperature-dependent thermal conductivities of - were measured using frequency domain thermoreflectance (FDTR), a non-contact optical technique that uses continuous-wave pump (515 nm) and probe (532 nm) lasers to measure the thermal properties. The pump laser, which serves as a temporally periodic, spatially Gaussian heat source, is focused on the sample and absorbed by the Au transducer. The thermoreflectance of Au at 532 nm enables the co-aligned probe laser to monitor the periodic temperature response, which has a phase lag relative to the pump laser that depends on the sample’s thermal properties. The phase lag between the pump (heat flux) and probe (temperature) lasers was measured for multiple modulation frequencies ranging from 100 kHz to 5 MHz. Details of this measurement procedure are described in our previous work on -.[18] Sensitivity analysis was performed to determine the sensitivity of phase lag to each parameter used in the analytical solution. The sensitivity of a parameter to the phase lag measured in FDTR is quantified as
which is the normalized change in phase per unit change in the parameter.[32] A high sensitivity to the targeted fitting parameter indicates that it can be accurately measured by FDTR. If FDTR is sensitive to another input parameter, then that parameter needs to be quantified externally with low uncertainty to minimize its unintentional influence on the fitted parameter.
The sensitivity analysis reveals that the FDTR is sensitive to the volumetric heat capacity of - (), the laser spot radius (), and the thermal conductivity of the sapphire substrate (). (3090 150 J/cmK) was determined from the reference values for the specific heat at K (506 J/kgK)[33] and density (6.1 g/cm).[31, 34] (2.6 0.1 m) was measured using a reference sample.
(Au-Cr transducer on fused silica) prior to the -GaO measurement. (38 2 W/mK) was measured separately using FDTR and was fixed for the -GaO measurement.
A 5 nm adhesion layer of Cr capped with a 65 nm Au transducer layer was deposited on top of the -GaO films using a Kurt Lesker PVD 75 Electron Beam Evaporator. The true combined thickness of the Au-Cr transducer () was measured with a KLA Tencor P-15 Profilometer. The composite electrical conductivity of the Au-Cr transducer was measured with the four-point probe (4PP) method. The Wiedemann-Franz law was used to determine the Au-Cr thermal conductivity from the electrical conductivity. Three parameters that cannot be determined externally are and the thermal boundary conductances at the Au-Cr/-GaO interface () and at -GaO/sapphire interface (). The -GaO film contains a -/-GaO transition region adjacent to the -sapphire substrate. Cross-sectional TEM reveals substantial variation in the thickness of this region and a diffuse boundary between the transition region and the -GaO film, without observable voids. Because the transition-layer thickness, composition, and thermal properties cannot be independently characterized, we represent the -GaO film and transition region as a single effective layer in the thermal model. Therefore, the extracted represents the effective cross-plane thermal conductivity of the combined -GaO/-/-GaO region, rather than the intrinsic conductivity of phase-pure -GaO. The sensitivity analysis reveals that the phase is marginally sensitive to throughout the entire range of modulation frequencies, as shown in Figure 2(b). For this reason, we simultaneously extracted thickness-dependent and temperature-dependent and , where includes and . The interfacial conductance was estimated by extrapolating the effective thermal resistance of the two thinnest films to zero thickness. We then used this estimated interfacial conductance to separate the interface contribution from the measured effective thermal conductivity and obtain the -GaO thermal conductivity for each film. Further details are provided in Section IV of the Supplementary Information. We expect to vary over different samples, as this parameter may be influenced by the transducer deposition conditions and the surface roughness.

Figure 2. (a) Stacking sequence of the sample. (b) Sensitivity analysis for the 159 nm -GaO film. (c) Measured phase lag and analytical solution fits for thickness-dependent measurements on -GaO films.
Uncertainties of the fitting parameters were determined using the Bayesian Parameter Estimation (BPE).[35] Previous FDTR uncertainty quantification methods, i.e., 1-variable Root Sum of Squares (RSS) and Monte Carlo,[36] quantify the uncertainties by finding a single local minimum of the sum of squared error (SSE). BPE, on the other hand, assigns a probability to a given set of parameters based on the SSE of the fit they generate. This probability is further modified by incorporating external information known about the parameters (i.e., the prior distributions). Here we report the median of the resultant probability distributions as the "best-fit" value, and the 5th and 95th percentiles as the lower and upper bounds of the 90% confidence interval. For our BPE analysis, we combined the Gaussian prior and uniform prior approach. We set two externally determined fixed parameters, (3090 150 J/cmK) and (2.6 0.1m), as Gaussian priors. We chose these parameters because the phase lag is sensitive to their values. Other control parameters were fixed in the BPE analysis because the phase lag is insensitive to their values and their values are well known. In the Gaussian prior, the weighting factor is equivalent to a Gaussian distribution centered at the externally determined value of our parameters, with standard deviations equal to the uncertainty in each parameter. Then, we set two fitting parameters, and , as uniform priors. In the uniform prior, all values were considered equally likely, which is more suitable for unknown parameters. Uniform prior bounds were initially centered on preliminary best-fit estimates solely to define a computationally tractable parameter grid; these estimates were not used as constraints in the Bayesian posterior evaluation. We verified prior-bound sensitivity by repeating the BPE analysis with systematically varied ranges and selected final bounds that fully contain the posterior distributions, confirming that the reported thermal conductivities are not driven by the chosen prior limits.
The thickness-dependent thermal conductivity of -GaO is compared to that of other polymorphs in Figure 3. Although the 90% confidence intervals of the -GaO films and -GaO measurements partially overlap, the median cross-plane thermal conductivity values of the -GaO films are lower than other experimentally measured GaO polymorphs at comparable thicknesses. At comparable film thicknesses, the -GaO films exhibit lower median values of cross-plane thermal conductivity than the other experimentally measured GaO polymorphs. This observation is consistent with lattice thermal conductivities predicted by first principles[22] and the only prior measurements.[25] One outlier is the computational study that reported an extremely low lattice thermal conductivity of -GaO (0.12 W/mK).[25] The size dependence in the thermal conductivity of -GaO is present (1.83 W/mK to 2.26 W/mK from 159 nm to 689 nm) but less prominent than - and -GaO.

Figure 3. Thickness-dependent thermal conductivity of GaO polymorphs. Inverted triangle symbols are -GaO from Karim et al. (pink)[21] and from Xiao et al. (green).[26] Square symbols are -GaO from our previous work (red),[18] Szwejkowski et al. (gray),[17] and Song et al. (light blue). Circle symbols are -GaO from our previous work (blue).[18] Diamond symbols are -GaO measured in this work (yellow) and from Xiao et al. (purple).[26] Our first-principles-based calculations, which use the interatomic force constants of Yang et al.,[22] are displayed as a black line.
First-principles-based calculations were performed to predict the size dependence of thermal conductivity in phase-pure -GaO films using the phonon Boltzmann transport equation. Previous first-principles-based studies have calculated the phonon properties and bulk thermal conductivity of -GaO.[22, 25, 26] Using the second- and third-order interatomic force constants provided to us by Yang et al.,[22] we reconstructed the mode-resolved lattice thermal conductivity within the relaxation time approximation. To account for the finite film thickness, phonon-boundary scattering was added to the intrinsic phonon-phonon scattering rate[37] using the Matthiessen rule. The thickness-dependent thermal conductivity was then obtained by recalculating the contribution of each phonon mode using the corrected phonon lifetimes and summing over all modes. Further details about the calculations are provided in Section VIII of the Supplementary Information. As shown in Figure 3, our measured thermal conductivities follow the calculation trend of increasing thermal conductivity with increasing film thickness. Four of the six measured points capture the calculations within their uncertainties. The measured thermal conductivities are, on average, 12% lower than the calculations. This discrepancy likely results from internal defects and/or the thin transition layer that contains other GaO phases, which introduce additional phonon scattering.
The weak size dependence observed in the thermal conductivity of -GaO is attributed to its intrinsically short phonon MFPs.[22, 24, 26] First-principles studies have shown that the phonon frequency spectrum of -GaO is significantly narrower than that of -GaO, which results in lower phonon group velocities.[38] This behavior arises from the complex crystal structure of the phase. Compared with the and phases, -GaO exhibits more distorted Ga-O polyhedra and a broader distribution of Ga-O bond lengths, which lowers the average bond stiffness and reduces phonon group velocities.[22] In addition, first-principles calculations report larger third-order force constants and Grüneisen parameters in -GaO, indicating stronger phonon anharmonicity and enhanced phonon-phonon scattering rates.[22] The structural complexity also leads to lower phonon participation ratios in -GaO, suggesting that a larger fraction of vibrational modes are spatially localized and contribute weakly to thermal transport.[24]
Since the thermal conductivity of thin-film -GaO is dominated by phonon-phonon scattering, increasing the film thickness is not expected to enhance its thermal conductivity significantly. This limitation hinders effective heat dissipation in -GaO-integrated devices. Instead, when thermal management is critical, the low thermal conductivity of -GaO can be complemented by growing it on high thermal conductivity polycrystalline diamond[39] or SiC[40, 41] substrates.
The temperature-dependent thermal conductivities of the 159 nm and 689 nm -GaO films from 293 K to 400 K are shown in Figure 4. For both films, the thermal conductivity decreases with increasing temperature due to enhanced phonon-phonon scattering. The junction temperature of GaO-based devices can reach up to 200 °C,[42] where the thermal conductivity of -GaO is further reduced, highlighting a challenge for effective thermal management. The temperature-dependent thermal conductivity data were fitted using , as shown in Fig. S11, yielding (95% CI: 0.17-0.29) for the 159 nm film and (95% CI: 0.61-1.26) for the 689 nm film. The temperature dependence in the thermal conductivity is not as pronounced in the 159 nm film, where phonon-boundary scattering is more prominent. Since boundary scattering is largely temperature-independent, it suppresses the temperature dependence of the overall thermal conductivity. This trend was also observed in -GaO from our previous measurement and the literature.[17] In contrast to - and -GaO, -GaO exhibits an increase in thermal conductivity with rising temperature, which is attributed to its disordered structure.[18] Temperature-independent phonon-defect scattering dominates in a disordered material, so the effective mean free path is nearly constant, and the thermal conductivity rises primarily through the increase in heat capacity with temperature.[18]

Figure 4. Temperature-dependent thermal conductivity of polymorphs. Square symbols are - from our previous work[18] and Song et al. (black empty).[17] Circle symbols are - from our previous work.[18] Diamond symbols are - measured in this work.
We measured the cross-plane thermal conductivity of (001) -GaO thin films on -plane sapphire substrates over thicknesses from 159 nm to 689 nm using FDTR. Across this thickness range, ranges from 1.83 W/m·K to 2.26 W/m·K and shows a weak thickness dependence, indicating that heat transport in -GaO is predominantly limited by intrinsically short phonon MFPs rather than phonon-boundary scattering. We also performed first-principles-based calculations to predict the size dependence in the thermal conductivity of -GaO, and the calculated trend agrees well with the experimental results. Temperature-dependent measurements between 293 and 400
reveal a moderate decrease in due to enhanced phonon-phonon scattering, with the thinner film exhibiting a weaker temperature dependence due to increased phonon-boundary scattering. When compared with literature-reported data and first-principles calculations for -, -, and -, - exhibits the lowest thermal conductivity at comparable thicknesses, which we attribute to its highly distorted polyhedral network, reduced group velocities, and strong anharmonicity that lead to short phonon MFPs. Our findings highlight the need for alternative thermal management strategies, such as integration with high thermal conductivity substrates (e.g., diamond or SiC) or engineered composite stacks, for --based power and RF electronics.
Supplementary Material
See the supplementary material for thin film strain and surface morphology characterization (Figs. S1 and S2); film thicknesses and associated uncertainties (Table S1); parameters used in the BPE uncertainty analysis (Table S2) and BPE posterior results for all six films (Figs. S3-S8); BPE posterior results for the thickness-dependent measurements (Table S3) and the temperature-dependent measurements of the 159 nm and 689 nm films (Tables S4 and S5, respectively); details of the linear extrapolation method used to estimate (Sec. S4 and Fig. S9); thermal conductivity results after removing for the thickness- and temperature-dependent measurements (Tables S6 and S7, respectively); phase lag data and analytical solution fits for the temperature-dependent measurements of the 159 nm and 689 nm films (Figs. S10 and S11, respectively); a power-law analysis of the temperature-dependent thermal conductivity (Fig. S12); sensitivity analyses for the 341 nm and 689 nm films (Figs. S13 and S14, respectively); and details of the calculations used to solve the phonon Boltzmann transport equation (Sec. S8).
Author’s Contributions
Seungwon Park: Conceptualization (lead); Data curation (lead); Formal analysis (lead); Methodology (lead); Software (lead); Visualization (lead); Validation (lead); Writing - original draft (lead); Writing - review & editing (lead). Jingyu Tang: Conceptualization (equal); Data curation (equal); Formal analysis (equal); Visualization (equal); Writing - original draft (lead); Writing - review & editing (equal). Minsung An: Data curation (support); Formal analysis (lead); Methodology (support); Software (support); Validation (support); Writing - review & editing (support). Alan J. H. McGaughey: Funding acquisition (lead); Project administration (lead); Supervision (lead); Writing - review & editing (lead). Lisa M. Porter: Funding acquisition (lead); Project administration (lead); Supervision (lead); Writing - review & editing (lead). Robert F. Davis: Funding acquisition (lead); Project administration (lead); Supervision (lead); Writing - review & editing (lead). Jonathan A. Malen: Funding acquisition (lead); Project administration (lead); Supervision (lead); Writing - review & editing (lead).
Acknowledgments
This work was supported by the Army Research Office Award No. W911NF2220191. The authors acknowledge the use of the Bertucci Nanotechnology Laboratory at Carnegie Mellon University supported by grant BNL-78657879 and use of the Materials Characterization Facility at Carnegie Mellon University supported by grant MCF-677785. The authors thank Jinkyu Kim for performing the AFM imaging and surface morphology characterization. The authors also thank Dr. Jinfeng Yang for providing the first-principles calculation data.
Conflict of Interest
The authors have no conflicts to disclose.
Data Availability
The data that support the findings of this study are available from the corresponding author upon reasonable request.
References
- [1]R. Roy, V. G. Hill, and E. F. Osborn, “Polymorphism of Ga₂O₃ and the System Ga₂O₃–H₂O,” Journal of the American Chemical Society 74, 719–722 (1952), publisher: American Chemical Society (ACS).
- [2]J. Tang, K. Jiang, P.-S. Tseng, R. C. Kurchin, L. M. Porter, and R. F. Davis, “Thermal stability and phase transformation of α-, κ(ε)-, and γ-Ga₂O₃ films under different ambient conditions,” Applied Physics Letters 125, 092104 (2024).DOI
- [3]F. He, K. Jiang, Y. Choi, B. L. Aronson, S. Shetty, J. Tang, B. Liu, Y. Liu, K. P. Kelley, G. B. Rayner, R. F. Davis, L. M. Porter, and S. Trolier-McKinstry, “High field dielectric response in κ-Ga₂O₃ films,” Journal of Applied Physics 134, 204101 (2023).DOI
- [4]M. B. Maccioni and V. Fiorentini, “Phase diagram and polarization of stable phases of (Ga₁−ₓInₓ)₂O₃,” Applied Physics Express 9, 041102 (2016).
- [5]Z. Chen, X. Lu, Y. Tu, W. Chen, Z. Zhang, S. Cheng, S. Chen, H. Luo, Z. He, Y. Pei, and G. Wang, “ε-Ga₂O₃ : An Emerging Wide Bandgap Piezoelectric Semiconductor for Application in Radio Frequency Resonators,” Advanced Science 9, 2203927 (2022).
- [6]J. Wang, H. Guo, C.-Z. Zhu, Q. Cai, G.-F. Yang, J.-J. Xue, D.-J. Chen, Y. Tong, B. Liu, H. Lu, R. Zhang, and Y.-D. Zheng, “ε-Ga₂O₃: A Promis ing Candidate for High-Electron-Mobility Transistors,” IEEE Electron Device Letters, 1–1 (2020).
- [7]Y. Lu, P. A. Miranda Cortez, X. Tang, Z. Liu, V. Khandewal, S. Krishna, and X. Li, “κ/κ′-Ga2O3 Type-II Phase Heterojunction,” Advanced Materials 37, 2406902 (2025).DOI
- [8]J. Lee, H. Kim, L. Gautam, and M. Razegghi, “High Thermal Stability of κ-Ga2O3 Grown by MOCVD,” Crystals 11, 446 (2021).
- [9]J. Tang, P.-S. Tseng, K. Jiang, R. C. Kurchin, R. F. Davis, and L. M. Porter, “Kinetic study of κ (ε) to β phase transformation in Ga2O3 thin films via in situ high-temperature XRD,” Applied Physics Letters 129 (2026).
- [10]H. Xue, Q. He, G. Jian, S. Long, T. Pang, and M. Liu, “An Overview of the Ultradwide Bandgap Ga2O3 Semiconductor-Based Schottky Barrier Diode for Power Electronics Application,” Nanoscale Research Letters 13, 290 (2018).
- [11]H. Higashiwaki, “β-Ga2O3 material properties, growth technologies, and devices: a review,” AAPPS Bulletin 32, 3 (2022).DOI
- [13]Z. Guo, A. Verma, X. Wu, F. Sun, A. Hickman, T. Masui, A. Kuramata, M. Higashiwaki, D. Jena, and T. Luo, “Anisotropic thermal conductivity in single crystal β-gallium oxide,” Applied Physics Letters 106, 111909 (2015).DOI
- [14]A. Jeżowski, P. Stachowiak, T. Suski, S. Krukowski, M. Boćkowski, I. Grzegory, and B. Danilchenko, “Thermal conductivity of bulk GaN single crystals,” Physica B: Condensed Matter 329–333, 1531–1532 (2003).DOI
- [15]Y. R. Koh, Z. Cheng, A. Mamun, M. S. Bin Hoque, Z. Liu, T. Bai, K. Hussain, M. E. Liao, R. Li, J. T. Gaskins, A. Giri, J. Tomko, J. L. Braun, M. Gaevski, E. Lee, L. Yates, M. S. Goorsky, T. Luo, A. Khan, S. Graham, and P. E. Hopkins, “Bulk-like Intrinsic Phonon Thermal Conductivity of Micrometer-Thick AlN Films,” ACS Applied Materials & Interfaces 12, 03978 (2020).
- [16]C. J. Szewczykowski, N. C. Creange, K. Sun, A. Giri, B. F. Donovan, C. Constantin, and P. E. Hopkins, “Size effects in the thermal conductivity of gallium oxide (β-Ga2O3) films grown via open-atmosphere annealing of gallium nitride,” Journal of Applied Physics 117, 084308 (2015).
- [17]Y. Song, P. Ranga, Y. Zhang, Z. Feng, H.-L. Huang, M. D. Santia, S. C. Badescu, C. U. Gonzalez-Valle, C. Perez, K. Ferri, M. L. Lavelle, D. W. Snyder, B. A. Klein, J. Deitz, A. G. Baca, J.-P. Maria, B. Ramos-Alvarado, J. Hwang, H. Zhao, X. Wang, S. Krishnamoorthy, B. M. Foley, and S. Choi, “Thermal Conductivity of β-Phase Ga2O3 and (AlxGa1−x)2O3 Heteroepitaxial Thin Films,” 13, 38477–38490.
- [18]S. Park, J. Liang, J. Tang, K. Jiang, A. Pathak, R. F. Davis, L. M. Porter, and J. A. Malen, “Size effects and temperature dependence in the thermal conductivity of γ-Ga2O3 films,” Applied Physics Letters 126, 232201 (2025).
- [19]G. Chen, “Thermal conductivity and ballistic-phonon transport in the cross-plane direction of superlattices,” Physical Review B 57, 14958–14973 (1998).DOI
- [20]D. G. Cahill, P. V. Braun, G. Chen, D. R. Clarke, S. Fan, K. E. Goodson, P. Keblinski, W. P. King, G. D. Mahan, A. Majumdar, H. J. Maris, S. R. Phillpot, E. Pop, and L. Shi, “Nanoscale thermal transport. II. 2003–2012,” Applied Physics Reviews 1, 011305 (2014).
- [21]A. Karim, Y. Song, D. C. Shoemaker, D.-W. Jeon, J.-H. Park, J. K. Mun, H. K. Lee, and S. Choi, “Thermal analysis of an α-Ga2O3 MOSFET using micro-Raman spectroscopy,” Applied Physics Letters 123, 192104 (2023).DOI
- [22]J. Yang, Y. Xu, X. Wang, X. Zhang, Y. He, and H. Sun, “Lattice thermal conductivity of β-, α-, and κ-Ga2O3: a first-principles computational study,” Applied Physics Express 17, 011001 (2024).DOI
- [23]X. Xiao and C. Yuan, “Insight into strain dependent lattice thermal conductivity of α- and κ-Ga2O3,” Applied Physics Letters 125 (2024), 10.1063/5.0232214.
- [24]Z. Sun, Z. Qi, K. Liang, X. Sun, Z. Zhang, L. Li, Q. Wang, G. Zhang, G. Wu, and W. Shen, “A neuroevolution potential for predicting the thermal conductivity of α, β, and ε-Ga2O3,” Applied Physics Letters 123, 192202 (2023).
- [25]H. Sun and G. Yang, “Influence of polymorphism on the lattice thermal conductivity of Ga2O3,” Journal of Vacuum Science & Technology A 42 (2024), 10.1116/6.0003844.
- [26]X. Xiao, Y. Mao, B. Meng, G. Ma, K. Hušeková, F. Evgenės, A. Rosová, E. Dobroč̌ka, P. Eliáš, M. Ťapajna, F. Gucmann, and C. Yuan, “Phase-Dependent Phonon Heat Transport in Nanoscale Gallium Oxide Thin Films,” Small 20, 2309961 (2024).DOI
- [27]J. Jiang, J. Tang, M. J. Cabral, A. Park, L. Gu, R. F. Davis, and L. M. Porter, “Layered phase composition and microstructure of κ-Ga2O3-dominant heteroepitaxial films grown via MOCVD,” Journal of Applied Physics 131, 055305 (2022).
- [28]Y. Zhu, Z. Chen, W. Tu, X. Ma, Y. Pei, and G. Wang, “β-ga2o3 versus ε-ga2o3: Control of the crystal phase composition of gallium oxide thin film prepared by metal-organic chemical vapor deposition,” Applied Surface Science 420, 802–807 (2017).
- [29]A. Hassa, C. Wouters, M. Kneißl, D. Splith, C. Sturm, H. von Wenckstern, M. Albrecht, M. Lorenz, and M. Grundmann, “Control of phase formation of (al x ga1- x) 2o3 thin films on c-plane al2o3,” Journal of Physics D: Applied Physics 53, 485105 (2020).
- [30]Y. Xu, J.-H. Park, Z. Yao, C. Wolverton, M. Razegghi, J. Wu, and V. P. Dravid, “Strain-induced metastable phase stabilization in ga2o3 thin films,” ACS applied materials & interfaces 11, 5536–5543 (2019).
- [31]I. Cora, F. Mezzadri, F. Boschi, M. Bosi, M. Čaplovičová, G. Calestani, I. Dódony, B. Pécz, and R. Fornari, “The real structure of ε-Ga2O3 and its relation to κ-phase,” CrystEngComm 19, 1509–1516 (2017).
- [32]B. C. Gundrum, D. G. Cahill, and R. S. Averback, “Thermal conductance of metal-metal interfaces,” Physical Review B 72, 245426 (2005).
- [33]C. Ribeiro Da Silva, F. Bechstedt, L. Kühl Teles, D. Nazaré De Freitas, and M. Marques, “Phonons and thermal properties of α-, β-, δ-, and κ-Ga2O3 polymorphs from first principles studies,” Journal of Vacuum Science & Technology A 43, 042805 (2025).
- [34]H. Y. Playford, A. C. Hannon, E. R. Barney, and R. I. Walton, “Structures of Uncharacterised Polymorphs of Gallium Oxide from Total Neutron Diffraction,” Chemistry – A European Journal 19, 2803–2813 (2013).
- [35]J. Drew, S. Godse, Y. Liang, A. Pathak, J. A. Malen, and R. C. Kurchin, “Analysis and uncertainty quantification of thermal transport measurements through Bayesian parameter estimation,” Review of Scientific Instruments 97, 034903 (2026).
- [36]J. Yang, E. Ziade, and A. J. Schmidt, “Uncertainty analysis of thermoreflectance measurements,” Review of Scientific Instruments 87, 014901 (2016).DOI
- [37]A. J. H. McGaughey, E. S. Landry, D. P. Sellan, and C. H. Amon, “Size-dependent model for thin film and nanowire thermal conductivity,” Applied Physics Letters 99, 131904 (2011).DOI
- [38]X. Wang, J. Yang, P. Ying, Z. Fan, J. Zhang, and H. Sun, “Dissimilar thermal transport properties in κ-Ga2O3 and β-Ga2O3 revealed by homogeneous nonequilibrium molecular dynamics simulations using machine-learned potentials,” Journal of Applied Physics 135, 065104 (2024).
- [39]M. Girolami, M. Bosi, S. Pettinato, C. Ferrari, R. Lolli, L. Seravalli, V. Serpente, M. Mastellone, D. M. Trucchi, and R. Fornari, “Structural and Photoelectronic Properties of κ-Ga2O3 Thin Films Grown on Polycrystalline Diamond Substrates,” Materials 17, 519 (2024).DOI
- [40]W. Xu, T. You, Y. Wang, Z. Shen, K. Liu, L. Zhang, H. Sun, R. Qian, Z. An, F. Mu, T. Suga, G. Han, X. Ou, Y. Hao, and X. Wang, “Efficient thermal dissipation in wafer-scale heterogeneous integration of single-crystalline β-Ga2O3 thin film on SiC,” Fundamental Research 1, 691–696 (2021).
- [41]Y. Song, D. Shoemaker, J. H. Leach, C. McGray, H.-L. Huang, A. Bhattacharyya, Y. Zhang, C. U. Gonzalez-Valle, T. Hess, S. Zhukovsky, K. Ferri, R. M. Lavelle, C. Perez, D. W. Snyder, J.-P. Maria, B. Ramos-Alvarado, X. Wang, S. Krishnamoorthy, J. Hwang, B. M. Foley, and S. Choi, “Ga2O3-on-SiC Composite Wafer for Thermal Management of Ultrawide Bandgap Electronics,” ACS Applied Materials & Interfaces 13, 40817–40829 (2021).DOI
- [42]B. Chatterjee, K. Zeng, C. D. Nordquist, U. Singisetti, and S. Choi, “Device-Level Thermal Management of Gallium Oxide Field-Effect Transistors,” IEEE Transactions on Components, Packaging and Manufacturing Technology 9, 2352–2365 (2019).DOI