WorksPhysics and Astronomy
Measuring Power with a Saturated Photodiode
Abstract
Accurate measurement of optical power is pivotal in many applications and scientific research. However, traditional power meters are unable to measure power levels beyond a certain saturation point, limiting their usefulness in high-power applications. In this technical note, I discuss how optical power can be measured using a saturated photodiode. I demonstrate that by monitoring both the dc photocurrent and ac noise, it is possible to accurately measure power levels beyond its saturation point.
Introduction
Optical power measurement is a critical aspect of many applications. It is the conventional wisdom that a saturated photodiode can not be used to measure power. Saturation power of photodiodes can be pushed to higher levels by applying a reverse bias voltage, however there is a limit to the amount of bias voltage due to the reverse breakdown which can be catastrophic to the diode. This limitation can be problematic in high-power applications, where it is important to be able to accurately measure power levels at high speed. In this technical note, I discuss a method for measuring optical power using a saturated photodiode. I demonstrate that the photocurrent noise decreases with power beyond saturation which can be used to accurately measure power at levels beyond its saturation point. This information might be useful in photon noise measurements.
Background
If a photoevent generated at produces an electric pulse , of area , in the external circuit. A photoevent generated at time then produces a displaced pulse, . Dividing the time axis into incremental time intervals so that the probability that a photoevent occurs within an interval is . The electric current at time is written as
where assumes the value 1 with probability , and 0 with probability . The variables are independent. The mean value of is . Its mean-square value is . The mean of the product is if , and if . The mean and mean-square values of are now determined via
Substituting , and taking the limit so that the summations become integrals, previous equations yield, respectively,
The limits of the integration is zero to infinity. It follows that
Definition of the bandwidth as
can be readily verified by noting that the Fourier transform of is its transfer function . The area under is simply . In accordance with Parseval’s theorem, the area under is equal to the area under the symmetric function , so that
The quantity is therefore the power-equivalent spectral width of the function (i.e., the bandwidth of the device/circuit combination). As an example, if for and 0 elsewhere, we get . Using this definition of bandwidth, we get back our familiar expression for the noise in photocurrent
So far this is a standard derivation of the shot noise[1]. Note that this expression hinges on the assumption that the area under is simply , basically one photoevent cause one electrons worth of charge to flow as current. However in saturation its definitely not the case and the photodiode response becomes a function of intensity. In the first order approximation, one can make the assumption that , where is a power dependent function that is 1 at low power and decreases at high power and area under is . Then we get
which gives us the key insight that the average value of current and noise power scales differently with incident optical power. If we take a ratio
we find that the signal to noise ratio (SNR) in principle is proportional to incident power despite the nonlinearity in the response. Even if this proportionality does not hold exactly, with proper calibration therefore it should be possible to measure the power with a saturated photodiode by measuring both the average photocurrent and the photocurrent noise.
Results
Figure 1A shows a schematic diagram of a standard photodiode driving circuit. The photodiode can be modelled as a current source in parallel with a diode[2]. A reverse bias voltage is applied to set the operating point, but there is a limit to how much voltage can be applied defined by junction breakdown[3]. Such a circuit can be simulated using conventional electrical circuit theory[4](MATLAB code below), the resulting operating current with realistic circuit parameters is shown in Figure 1B. We can see that the photodiode saturates at some power and the saturation knee increases with reverse bias voltage. The highest measurable power is determined by the highest reverse bias voltage that can be applied across a junction. Below saturation the current is linear with incident power, which is expected.
Figure 1. Schematic diagram of a photodiode driving circuit and simulated operating current .
Experimental data of a reverse biased photodiode is shown in Figure 2 where reverse bias is seen to increase the saturation power. Before saturation the voltage is proportional to power. After saturation no measurement of power is possible, which is the current paradigm.
 bbox=0.34,0.39,0.67,0.66
Figure 2. Output voltage across the 25 load resistance from a Thorlabs FDGA0551InGaAs photodiode at different reverse bias excited by a 1070 nm CW laser. It has a 0.95 A/W responsivity, 2.5 ns rise time and 0.5 mm active area diameter.
We can now attempt to measure power beyond saturation. In Figure 3A we show the photovoltage and the photocurrent noise as a function of incident power. Photocurrent noise is measured around 1.5 MHz with a spectrum analyzer (10 kHz resolution bandwidth, 1 MHz span, with preamplifier on and no attenuation, electronic noise floor is −165 dBm/Hz). Below saturation photovoltage and noise increases simultaneously. As the photovoltage is saturated, the photocurrent noise suddenly decreases. This qualitatively follows our theoretical voltage and noise shown in Figure 1. In Figure 3B we show the photovoltage and SNR calculated from the experimental data. Beyond saturation SNR changes with incident power, which can be used to measure power after proper calibration. Such behaviour also holds at other noise frequencies as long as they are lower than the bandgap of the photodiode and away from noise.
 bbox=0.16,0.67,0.85,0.91
Figure 3. (A) Output voltage and noise from a Excelitas C30641GH62InGaAs photodiode at 30 V reverse bias excited by a 1550 nm femtosecond pulsed laser. It saturates around 25 mW. (B) Even though photovoltage has saturated, the SNR shows response beyond the saturation power.
Discussion
Even when a photodiode is saturated, the information about the photon flux intensity are not completely lost and in a way encoded in the photocurrent noise, which can be practically used to measure power at high speed after proper calibration.
Codes
%% Matlab code to solve for photocurrent and noise in a circuit
clc;clear all;close all;
P=linspace(0,100,1000)*1e-3; % Incident power in W
Responsivity=1;
Ip=P*Responsivity; % Expected photocurrent
R=500;
V=[linspace(-50,0,1e5),linspace(0,.7,1e5)];
VR=30; % Reverse Bias Voltage
Iop=zeros(size(P)); % Operating Photocurrent
for indx=1:length(P)
I1=-Ip(indx)+0.1e-9*exp(V/.0259);
I2=-(V+VR)/R;
[~,pos]=min(abs(I1-I2));
Iop(indx)=-I2(pos);
end
figure(1);subplot(121), plot(P/1e-3,Iop); % Operating Current vs Power
f=Iop./P; %nonlinear response function
S=10*log10(2*1.6e-19*R*1*(P/1e-3).*(f.^2)); % Noise power vs optical power
subplot(122), plot(P/1e-3,S);
References
Acknowledgements
The author acknowledges Nicholas Rivera, Jamison Sloan, Yannick Salamin, chatGPT for their discussions. All equipment used in the experiments are properties of MIT.
References
- [1]Saleh, B. E. & Teich, M. C. Fundamentals of Photonics (John Wiley & Sons, 2019).
- [2]Bhattacharya, P. Semiconductor Optoelectronic Devices (Prentice-Hall, Inc., 1997).
- [3]Neamen, D. A. Semiconductor Physics and Devices: Basic Principles (McGraw-hill, 2003).
- [4]Sedra, A. S., Smith, K. C., Carusone, T. C. & Gaudet, V. Microelectronic Circuits, vol. 4 (Oxford University Press New York, 2004).