betaFeedback

WorksPhysics and Astronomy

Analytical Model for Gaussian Disorder Traps in Organic Thin-Film Transistor

Abstract

Structural defects and chemical impurities exist in organic semiconductors acting as trap centers for the excited states. This work presents a novel analytical model to calculate the trapping and detrapping rates between two Gaussian density of states. Miller-Abrahams rate and Fermi-Dirac statistics are employed in this model. The introduction of effective filled and empty sites for correlated bands greatly simplifies the expression of recombination rate. A technology computer-aided design simulator was used to simulate the donor-like traps in an organic semiconductor DPP-DTT based thin-film transistor, showing good agreement with the measured transfer characteristic.

Introduction

Organic semiconductors are a class of promising materials for high-efficiency1, low-cost2, flexible3, and multifunctional4 electronic devices. The trap states induced by the chemical impurities and structural defects in organic semiconductors play a critical role in electric performance.

For example, chemical impurities have been doped in host materials as guest molecules to improve the electroluminescence in light-emitting diodes5,6 and to enhance the light absorption efficiency in dye sensitized solar cells7,8. Other reports directly utilized the physics of trap states to build memories and sensors9–11.

However, the applications of organic semiconducting materials in different areas are restricted by the trap states for the following two reasons: 1) the traps can serve as unintentional recombination centers in light-emitting diodes and solar cells12,13, 2) carrier transport is also localized by chemical impurities and structural defects, resulting in carrier mobilities far below the theoretical prediction14,15. The study of trap related mechanisms is therefore crucial in extracting theoretical performance limits of organic semiconductors. Still many questions and challenges need to be addressed before engineering high-performance electronic devices.

In order to clarify the underlying mechanisms of trap related physics, several numerical methods have been proposed. The simplest approach included several discrete energy depths for traps, assuming that the trapping and detrapping rates are standard first order differential equations with time16,17. However, the trap states in organic semiconductors are dominated by continuous energy distributions11,18. Several works employed Gaussian distribution or exponential functions for trap levels to analyze the field-induced detrapping and thermal aging effects in organic semiconductors17,19,20. These works were mostly based on the master equation approach or Monte Carlo simulation19,21. However, both approaches are time-consuming methods for device simulation19. Hence, a more efficient and versatile approach is desired to explore the trap related kinetics.

In this study, we demonstrate a new method to analyze the charge generation (trapping) and recombination (detrapping) rate between two Gaussian density of states (DOS), by combining the Fermi-Dirac statistics with Miller-Abrahams equation22 Two variables of effective filled site (EFS) and effective empty site (EES) are defined in the expression of detrapping rate to simplify the algorithm complexity. Then, this method is applied to the understanding of the highest occupied molecular orbit (HOMO) and the donor-like trap (DLT) states in a Poly[2,5-(2-octyldodecyl)-3,6-diketopyrrolopyrrole-alt-5,5-(2,5-di(thien-2-yl)thieno [3,2-b]thiophene)] (DPP-DTT)23 based organic thin-film transistor(OTFT). The simulated results demonstrated a technology computer-aided design (TCAD) platform of DEVSIM24 show good agreement with the measured transfer characteristic. This model can also be applied to other types of traps in organic electronic materials, such as acceptor-like traps.

Modeling

In both organic and inorganic materials, the energetic distribution of trap states is typically approximated by a Gaussian function with a standard energetic deviation or an exponential function with a modified characteristic temperature11,18,20,25,26. The Gaussian function is a better choice to describe the limited nature of trap density.

Because of the less crystallized structure in organic materials, the energetic disorder of conductive bands in organic semiconductors are typically also given by Gaussian DOS27. Unlike the inorganic crystalline structure, there is no clear boundary between the allowed band and the forbidden band28. Boltzmann statistics is therefore not a proper approximation for the states in amorphous organic semiconductors28 and Fermi–Dirac statistics should be employed to calculate the average number in a single-particle state29.

The charge transition model, including trapping and detrapping, between various energy levels in organic semiconductors must be treated differently from inorganic crystals. In the following context, we employ Gaussian DOS to describe energy statistics for both of HOMO and DLT, and then use Miller-Abrahams rate and Fermi–Dirac statistics to describe the charge transition between these two energy levels.

A The Gaussian DOS for HOMO and DLT

The Gaussian DOS for HOMO (gHg_H) of organic materials is as follows:

gH(EH,EHc,σH)=NHσH2πexp⁡(−(EH−EHc)22σH2)(1)g_H(E_H,E_{Hc},\sigma_H)=\frac{N_H}{\sigma_H\sqrt{2\pi}}\exp\left(-\frac{(E_H-E_{Hc})^2}{2\sigma_H^2}\right) \tag*{(1)}

where EHE_H is an energy level of a specific state in HOMO. NHN_H, σH\sigma_H, and EHcE_{Hc} are the total density, the distribution width, and energy center of HOMO DOS, respectively. In the following content, we will use gH(EH)g_H(E_H) as a shorthand for gH(EH,EHc,σH)g_H(E_H,E_{Hc},\sigma_H).

The black solid curve in Figure 1(a) represents the Gaussian distribution for HOMO DOS and the empty sites in it. In addition, a hole is defined to be the remaining delocalized positive charge after an electron escapes form a HOMO site, whose density is:

Figure 1. The diagrams of filling states in Gaussian DOS for HOMO and DLT

p=∫−∞∞gH(EH,EHc,σH)(1−f(EH,EHf))dEH(2)p=\int_{-\infty}^{\infty}g_H(E_H,E_{Hc},\sigma_H)(1-f(E_H,E_{Hf}))\mathrm{d}E_H \tag*{(2)}

in which f(E,Ef)f(E,E_f) is Fermi–Dirac statistics and it reads:

f(E,Ef)=1eE−EfkBT+1(3)f(E,E_f)=\frac{1}{e^{\frac{E-E_f}{k_BT}}+1} \tag*{(3)}

where EfE_f, kBk_B, TT are Fermi energy level, Boltzmann’s constant, and the absolute temperature, respectively. It should be noted that, only in the equilibrium state, different bands in the system share the same Fermi level. Otherwise, in the non-equilibrium state, every band has its own Fermi level to describe the overall occupation of the sites30. In such condition, this energy level is termed as quasi Fermi level. As the trapping and detrapping processes typically occur in a non-equilibrium state, we should use quasi Fermi level of different bands in the following context, i.e. EHfE_{Hf} for HOMO and EDfE_{Df} for DLT.

The trapped charges consist of both donor-like and acceptor like states across the forbidden energy gap31. Then, the DOS for deep-level DLT is in the same manner of Gaussian distribution:

gD(ED,EDc,σD)=NDσD2πexp⁡(−(ED−EDc)22σD2)(4)g_D(E_D,E_{Dc},\sigma_D)=\frac{N_D}{\sigma_D\sqrt{2\pi}}\exp\left(-\frac{(E_D-E_{Dc})^2}{2\sigma_D^2}\right) \tag*{(4)}

where EDE_D is an energy level of a specific state in DLT. NDN_D, σD\sigma_D, and EDcE_{Dc} are the total density, the distribution width, and energy center of DLT DOS, respectively. In the following content, we will use gD(ED)g_D(E_D) as a shorthand for gD(ED,EDc,σD)g_D(E_D,E_{Dc},\sigma_D).

The black solid curve in Figure 1(b) represents the Gaussian distribution for DLT and the empty sites in it. Since the DLT site is neutral if occupied by an electron and positively charged if empty, the density of trapped charge corresponds to the empty sites. Then the trap density reads:

pD=∫−∞∞gD(ED,EDc,σD)(1−f(ED,EDf))dED(5)p_D=\int_{-\infty}^{\infty}g_D(E_D,E_{Dc},\sigma_D)(1-f(E_D,E_{Df}))\mathrm{d}E_D \tag*{(5)}

B Miller-Abrahams Equation

To describe the transition rate of electrons from one site with energy level EiE_i to another site with EjE_j, we employ Miller-Abrahams rate19,22, which reads:

νij=ν0exp⁡(−2Rijai−Ej−Ei+∣Ej−Ei∣2kBT)(6)\nu_{ij}=\nu_0\exp\left(-\frac{2R_{ij}}{a_i}-\frac{E_j-E_i+\lvert E_j-E_i\rvert}{2k_BT}\right) \tag*{(6)}

where ν0\nu_0 is attempt frequency, aia_i is the localization scale of initial state, RijR_{ij} is the distance between both states.

C Trapping Process

For the trapping process, the electron jumps from a neutral DLT site to an empty HOMO site. Here, we assume that all states of DLT are higher than HOMO, because Gaussian distributed DLT are deep-level bands31. Then by integrating the transition rates of all electrons in DLT to all empty site in HOMO, we can get the total rate of trapping. Figure 2 exhibits this process. Hence, the overall trapping rate reads:

Figure 2. The diagrams of electron’s trapping process from the neutral sites in DLT to the empty sites in HOMO. pp and nHn_H are the empty sites(holes) and the filled sites in HOMO DOS. nDn_D and pDp_D denote the filled and the empty sites in DLT DOS

kT=∫−∞∞∫−∞∞vDHgD(ED)f(ED,EDf)gH(EH)(1−f(EH,EHf)) dEDdEH(7)k_T = \int_{-\infty}^{\infty}\int_{-\infty}^{\infty} v_{DH}g_D(E_D)f(E_D,E_{Df})g_H(E_H)(1-f(E_H,E_{Hf}))\,\mathrm{d}E_D\mathrm{d}E_H \tag*{(7)}

where EDE_D, EHE_H are two energy sites located on DLT and HOMO, respectively. vDHv_{DH} is Miller-Abrahams rate for electron transition form site of EDE_D to EHE_H. It reads:

vDH=v0exp⁡(−2αDRDH)(8)v_{DH}=v_0\exp(-2\alpha_D R_{DH}) \tag*{(8)}

where αD\alpha_D is the inverse localization scale of DLT site, RDHR_{DH} is the average distance from HOMO sites to DLT sites.

After separating variables, the above expression can be simplified as:

kT=vDHnDp(9)k_T=v_{DH}n_Dp \tag*{(9)}

in which nDn_D is the filled sites in DLT. It is illustrated as the orange area in Figure 2 and reads:

nD=∫−∞∞gD(ED,EDc,σD)f(ED,EDf) dED=ND−pD(10)\begin{aligned} n_D=\int_{-\infty}^{\infty}g_D(E_D,E_{Dc},\sigma_D)f(E_D,E_{Df})\,\mathrm{d}E_D \\ &=N_D-p_D \tag*{(10)} \end{aligned}

Detrapping Process

For the detrapping process, the electron jumps from a filled HOMO site to an empty DLT site as indicated by the red solid arrow in Figure 3. Then by integrating all electrons in HOMO to all empty sites in DLT, we can get the total rate of detrapping. So the detrapping rate reads:

The diagrams of electron’s detrapping process from HOMO to the empty sites in DLT

Figure 3. The diagrams of electron’s detrapping process from HOMO to the empty sites in DLT. nHn_H is the actual filled sites and nH′n'_H is the effective filled sites in HOMO. pDp_D is actual empty sites and pD′p'_D is the effective empty sites in DLT

kD=∫−∞∞∫−∞∞vHDgH(EH)f(EH,EHf)gD(ED)(1−f(ED,EDf)) dEHdED(11)k_D=\int_{-\infty}^{\infty}\int_{-\infty}^{\infty}v_{HD}g_H(E_H)f(E_H,E_{Hf})g_D(E_D)(1-f(E_D,E_{Df}))\,\mathrm{d}E_H\mathrm{d}E_D \tag*{(11)}

where vHDv_{HD} is Miller-Abrahams rate for electron’s transition form the site of EHE_H in HOMO to EDE_D in DLT. vHDv_{HD} reads:

vHD=v0exp⁡(−2RDHaH−ED−EHkBT)(12)v_{HD}=v_0\exp\left(-2\frac{R_{DH}}{a_H}-\frac{E_D-E_H}{k_BT}\right) \tag*{(12)}

where aHa_H is the average localization scale of HOMO site. Using the following replacement:

vHD0=v0exp⁡(−2αHRDH)(13)v_{HD0}=v_0\exp(-2\alpha_HR_{DH}) \tag*{(13)}

the expression of Eq. (11) can be rewritten as:

kD=∫−∞∞∫−∞∞vHD0exp⁡(−ED−EHkBT)gH(EH)f(EH,EHf)gD(ED)(1−f(ED,EDf)) dEHdED(14)k_D=\int_{-\infty}^{\infty}\int_{-\infty}^{\infty}v_{HD0}\exp\left(-\frac{E_D-E_H}{k_BT}\right)g_H(E_H)f(E_H,E_{Hf})g_D(E_D)(1-f(E_D,E_{Df}))\,\mathrm{d}E_H\mathrm{d}E_D \tag*{(14)}

Effective Empty and Filled Sites

Eq. (14) has one more exponential terms than Eq. (7), but it can still be simplified by the method of separation of variables. Here, we define two parameters of EHc′E'_{Hc} and EDc′E'_{Dc} as effective energy centers for HOMO and DLT DOS, respectively. The expressions of two effective energy centers are:

EHc′=EHc+σH2kBT(15)E^\prime_{Hc}=E_{Hc}+\frac{\sigma_H^2}{k_BT} \tag*{(15)}
EDc′=EDc−σD2kBT(16)E^\prime_{Dc}=E_{Dc}-\frac{\sigma_D^2}{k_BT} \tag*{(16)}

Figure 3 illustrate the energy shift of EHc′E^\prime_{Hc} and EDc′E^\prime_{Dc} with respect to EHcE_{Hc} and EDcE_{Dc}, respectively. By introducing effective energy centers for both HOMO and DLT levels, Eq. (14) can be rewritten as:

kD=cEvDH0∬−∞∞gH(EH,EHc′,σH)f(EH,EHf)gD(ED,EDc′,σD)(1−f(ED,EDf))dEHdED(17)k_D=c_Ev_{DH0}\iint_{-\infty}^{\infty}g_H(E_H,E^\prime_{Hc},\sigma_H)f(E_H,E_{Hf})g_D(E_D,E^\prime_{Dc},\sigma_D)(1-f(E_D,E_{Df}))dE_HdE_D \tag*{(17)}

in which cEc_E reads:

cE=exp⁡(σH2+σD22kB2T2+EHc−EDckBT)(18)c_E=\exp\left(\frac{\sigma_H^2+\sigma_D^2}{2k_B^2T^2}+\frac{E_{Hc}-E_{Dc}}{k_BT}\right) \tag*{(18)}

Compared with Eq. (7), Eq. (17) can also be simplified to a product form like Eqs. (9):

kD=cEvDH0nH′pD′(19)k_D=c_Ev_{DH0}n^\prime_Hp^\prime_D \tag*{(19)}

in which nH′n^\prime_H reads:

nH′=∫−∞∞gH(EH,EHc′,σH)f(EH,EHf)dEH(20)n^\prime_H=\int_{-\infty}^{\infty}g_H(E_H,E^\prime_{Hc},\sigma_H)f(E_H,E_{Hf})dE_H \tag*{(20)}

and pD′p^\prime_D reads:

pD′=∫−∞∞gD(ED,EDc′,σD)(1−f(ED,EDf))dED(21)p^\prime_D=\int_{-\infty}^{\infty}g_D(E_D,E^\prime_{Dc},\sigma_D)(1-f(E_D,E_{Df}))dE_D \tag*{(21)}

Because Eqs. (20) and (21) are similar to Eqs. (10) and (5), respectively, we define nH′n^\prime_H as EFS for HOMO and pD′p^\prime_D as EES for DLT.

So far, we used both Fermi-Dirac statistics and Miller-Abrahams equation to derive the trapping and detrapping rates of DLT in the Gaussian energetic disorder semiconductors. The calculation complexity caused by the barrier in the detrapping process was reduced by virtue of introducing EFS and EES for the correlated bands. Then the detrapping rate is simplified from a sophisticated integral expression (Eq. (11)) to a concise product form (Eq. (19)). The black dot arrow in Figure 3 indicates the simplified detrapping picture. In the following section, we will analyze the relationship between different parameters and variables in this model. Then, this model was employed to simulate a DPP-DTT based transistor with a bottom-gate/ top-contact configuration.

Data ANALYSIS

Parameters and Variables

In the above content, the trapping and detrapping rates are reduced to the product forms in Eq. (9) and (19). The coefficient vDHv_{DH} for trapping in Eq. (9) reflects the impacts of orbit localization in DLT and spacial distance from HOMO to DLT. The other two variables are the filled electrons in DLT (nDn_D) and the empty sites in HOMO (pp). But for the detrapping rate, there’s an extra coefficient of cEc_E in Eq. (19). Figure 4 (a) and (b) present the dependence of cEc_E on the barrier height and the band width of Gaussian DOS. In Figure 4 (a), cEc_E shows a dramatically exponential decay with respect to the barrier height between the Gaussian centers of HOMO and DLT. This feature intuitively describes the physical role of energy barrier. However, there are two results to note: ① most of cEc_E values within the range shown in Figure 4 is greater than 1; ② the range of cEc_E decreases with device temperature for in Figure 4 (a) and (b). Both results are inconsistent with Miller-Abrahams rate in Eq. (6), because the detrapping rate should be reduced by the energy barrier (cE<1c_E<1) and enhanced with higher temperature. So, the attenuation effect of the potential barrier on detrapping process will act more on EES and EFS. In Eq. (19).

Figure 4. (a) Dependencies of cEc_E on barrier height (EDc−EHcE_{Dc}-E_{Hc}) at various temperature. All Gaussian widths for these lines are fixed at 0.11 eV. (b) Dependencies of cEc_E on one band width of Gaussian HOMO or DLT DOS at various temperature. The barrier height for these curves are set to 0.25 eV.

Figure 5 presents the dependence of EES and EFS on the actual charge density of nHn_H in HOMO and pDp_D in DLT, respectively. These data are obtained by Paasch’s method about the Gauss–Fermi integral27. It can be observed from Figure 5 (a) that the nHn_H relationship with the nHn_H asymptotically reaches a slope equal to 1 in the log-log plot for small densities. And, the pD′p^\prime_D relationship with the pDp_D presents the same manner. In this region, the values of nHn_H and pD′p^\prime_D are 5 ∼ 15 orders of magnitude smaller than nHn_H and pDp_D, respectively. The magnitude of difference increases with the Gaussian DOS widths, because the energy shift of EHc′E^\prime_{Hc} and EDc′E^\prime_{Dc} increases with these two widths in Eqs. (15) and (16). However, these magnitude differences decrease when nHn_H and pDp_D become saturated. So the slop of these curves becomes very steep in these regions in both Figure 5 (a) and (b). Such phenomenon reflects the saturation characteristic of the Gaussian distribution. Take the Gaussian HOMO DOS as example, the quasi Fermi level is the only variable of EFS’ expression in Eq. (21). So, while the actual filled sites in HOMO DOS are saturated, the raised effective energy center of EHc′E'_{Hc} makes EFS increase obviously.

Figure 5. (a) Dependencies of nH′n_H' on nHn_H of various band width for Gaussian HOMO DOS at 300K. (b) Dependencies of pD′p_D' on pDp_D for various band width of Gaussian DLT DOS at 300K. The total density for HOMO and DLT DOS are 1.2×1021 cm−31.2 \times10^{21}\ \mathrm{cm}^{-3} and 1.0×1019 cm−31.0 \times10^{19}\ \mathrm{cm}^{-3}, respectively.

TCAD Simulation for OTFT

In organic semiconductors, the surface trap density is more prominent than the bulk trap density. A device with active region on the surface is therefore an appropriate application to validate this method. And OTFT meats this criteria, because the conductive channel is located in the interface area of semiconductors.

In the following content, we demonstrate our model in a TCAD simulation of an OTFT device with the bottom-gate/top-contact configuration. The simulation parameters and device dimensions are listed in Table I. The DEVSIM24 TCAD simulator was employed to realize a finite volume method (FVM) analysis. The typical TCAD approach of drift-diffusion model solves three equations:

ModelSymbolValueUnit
Device temperatureTT300K
Total density for HOMO32NHN_H1.2×10211.2 \times10^{21}cm−3\mathrm{cm}^{-3}
HOMO DOS width29,30σH\sigma_H0.13eV
HOMO DOS center33EHcE_{Hc}-5.2eV
LUMO DOS center33-3.5eV
Total density for DLT11NDsN_{Ds}1.0×10131.0 \times10^{13}cm−2\mathrm{cm}^{-2}
DLT DOS widthσD\sigma_D0.11eV
DLT DOS centerEDcE_{Dc}3.81eV
Trap thicknessdDd_D3nm
Average distance between HOMO and DLTRDHR_{DH}5nm
Localization length for HOMO and DLT19aia_i0.5nm
Attempt frequency19ν0\nu_01s−1\mathrm{s}^{-1}
DPP-DTT thickness40nm
Insulator’s thickness300nm
OTFT channel length100μm\mu\mathrm{m}
Relative permittivity for DPP-DTTεr-Semi\varepsilon_{r\text{-}Semi}4
Relative permittivity for Insulator SiO2_2εr-SiO2\varepsilon_{r\text{-}SiO_2}3.9
Thermionic emission velocity at source and drain3410710^7cm/s\mathrm{cm/s}

Table I. The parameters used to simulate the DPP-DTT based OTFT if not explicitly stated elsewhere.

The Poisson equation:

−∇(εrε0∇ψ)=e⋅(p−n+pD)(22)-\nabla(\varepsilon_r\varepsilon_0\nabla\psi) = e \cdot(p-n+p_D) \tag*{(22)}

where ψ\psi is electrical potential, ε0\varepsilon_0 is the permittivity of vacuum, εr\varepsilon_r is the relative permittivity of the organic material, and ee is the elementary charge.

Hole Continuity Equation:

∂p∂t=∇(pμp∇ψ+Dp∇p)+Gp(23)\frac{\partial p}{\partial t} = \nabla(p\mu_p\nabla\psi+ D_p\nabla p) + G_p \tag*{(23)}

where μp\mu_p, DpD_p and GpG_p are the mobility, diffusion coefficient and net generation rate for holes, respectively.

Electron Continuity Equation:

∂n∂t=∇(−nμn∇ψ+Dn∇n)+Gn(24)\frac{\partial n}{\partial t} = \nabla(-n\mu_n\nabla\psi+ D_n\nabla n) + G_n \tag*{(24)}

where μn\mu_n, DnD_n and GpG_p are the mobility, diffusion coefficient and net generation rate of electrons, respectively.

To calculate the variance of DLT density over time, an extra equation for the net generation rate of DLT is solved simultaneously with the above three equations. The net generation rate of DLT reads:

∂qD∂t=kT−kD(25)\frac{\partial q_D}{\partial t} = k_T-k_D \tag*{(25)}

As our method is based on the bulk density of DLT, we convert the total surface trap density to the total bulk density through an exponential decay relationship with depth:

ND=NDsdDexp⁡(−xdD)(26)N_D=\frac{N_{Ds}}{d_D}\exp\left(-\frac{x}{d_D}\right) \tag*{(26)}

where xx is the depth from the insulator-semiconductor interface to the semiconducting layer, dDd_D is the characteristic thickness of DLT. The values for these parameters are listed in Table I. Integrating Eq. (26) on the depth in semiconductor layer, the sum of bulk density is consistent with surface density.

Here, we assume there is only one kind of trap. So, in Eq. (22), the total charges in Poisson’s equation include three parts: holes, electrons and DLT. As the organic OTFT works in the accumulation regime for on-state and depletion regime for off-state, we take only the electron’s transition between HOMO and DLT in consideration. Then, we can get the following two results:

Gp=−(kT−kD)(27)G_p = -(k_T-k_D) \tag*{(27)}
Gn=0(28)G_n = 0 \tag*{(28)}

For the carriers transport, we use the macroscopic conductivity model for holes 15,35 and Poole–Frenkel model for electrons 31. Then, a typical model for Schottky contacts is considered on source and drain 36. The thermionic emission velocity for holes and electrons is listed in Table. I. The initial equilibrium was solved while kTk_T equal to kDk_D.

Experiment and Simulation Results

To examine our method, we fabricated a bottom-gate/top-contact OTFT by using DPP-DTT as active layer.

Fig. 6 (a) demonstrates the device structure. The architecture details are listed in Table. I. The DPP-DTT is an excellent p-type organic semiconductor material with high carrier mobility and stable chemical structure23. Its energy levels are listed in Table. I. For the fabrication procedure, we first deposited its 5mg/ml chlorobenzene solution via spin-coating on a octyltrichlorosilane (OTS-8) treated Si/SiO2_2 substrate. Then, 100nm gold layers were thermal evaporated using a shadow mask as source and drain electrodes. The electrical measurements for this OTFT was carried out by a Keithley 4200 semiconductor analyzer in atmosphere. The source contact was grounded and the drain bias was set to -15 V. The gate bias was first swept forwardly from 50 V to -100 V, then swept back to 50 V. The sweeping speed of gate bias was 10 V/s.

Both measured and simulated results are showed in Figure 6 (b) and (c). All of simulation parameters are listed in Table I. In Figure 6(b), the DLT charges increase while the device is driven to hole accumulation regime with enough negative gate bias. But as a nonequilibrium process, the trap concentration did not synchronize with the gate bias. The maximum point for DLT charges occurs around -60 V while sweeping the gate bias back to 50V. Figure 6(c) presented the simulated and measured transfer characteristic curves. Due to the accumulation of trapped DLT charges, the drain current in backward scan is smaller than that in forward scan. So, the Transfer curves present an anti-clockwise hysteresis loop and the threshold voltage shifts about -16 V in the backward scan.

Figure 6. (a) Schematic of the OTFT structure and layer composition. (b) The simulated DLT charge density versus gate bias. (c) The comparison of transfer characteristic between simulated and measured results. The arrows in (b) and (c) denote the sweeping direction of gate bias.

Conclusion and Future Work

We have combined theoretical framework of the trapping and detrapping pictures in organic semiconductors that comprise two Gaussian DOSs. Through the introducing of EES for DLT and EFS for HOMO, both trapping and detrapping expression were reduced to two simple product forms. This model is demonstrated in a FVM based device simulator. To verify this model, we fabricated a DPP-DTT based TFT with bottom-gate/top-contact configuration. The good agreement of the simulated and experimental results testify the reasonability of this model. A more detailed analysis on charge trapping is a subject for further investigation.

Acknowledgements

This work is granted by the Natural Science Foundation of Guizhou Province (No. QKHJC-ZK[2021]YB329 and QKHJC-ZK[2021]YB018). We thanks Mr. Wenxuan Qiu for his language support.

References

  1. [1]¹ M. A. Baldo, “External quantum efficiency above 100% singlet-exciton-fission-based organic photovoltaic cell,” Science 340, 334–337 (2013).DOI
  2. [2]²F. J. Lin, C. Guo, W. T. Chuang, C. L. Wang, Q. Wang, H. Liu, C. S. Hsu, and L. Jiang, “Directional solution coating by the chinese brush: A facile approach to improving molecular alignment for high-performance polymer tfts,” Adv Mater 29 (2017), 10.1002/adma.201606987.DOI
  3. [3]³Q. Zhao, H. Wang, Z. Ni, J. Liu, Y. Zhen, X. Zhang, L. Jiang, R. Li, H. Dong, and W. Hu, “Organic ferroelectric-based 1t1t random access memory cell employing a common dielectric layer overcoming the half-selection problem,” Adv Mater 29 (2017), 10.1002/adma.201701907.DOI
  4. [4]⁴A. K. Pandey and J.-M. Nunzi, “Rubrene/fullerene heterostructures with a half-gap electroluminescence threshold and large photovoltage,” Advanced Materials 19, 3613–3617 (2007).DOI
  5. [5]⁵M. Gross, D. C. Müller, H.-G. Nothofer, U. Scherf, D. Neher, C. Bräuchle, and K. Meerholz, “Improving the performance of doped π-conjugated polymers for use in organic light-emitting diodes,” Nature 405, 661–665 (2000).pubmed.ncbi.nlm.nih.gov/10864318
  6. [6]⁶M. Pfeiffer, K. Leo, X. Zhou, J. Huang, M. Hofmann, A. Werner, and J. Blochwitz-Nimoth, “Doped organic semiconductors: Physics and application in light emitting diodes,” Organic Electronics 4, 89–103 (2003), high Efficiency Light Emitters.DOI
  7. [7]⁷A. Hagfeldt, G. Boschloo, L. Sun, L. Kloo, and H. Pettersson, “Dye-sensitized solar cells,” Chemical reviews 110, 6595–6663 (2010).DOI
  8. [8]⁸I. Paci, J. C. Johnson, X. Chen, G. Rana, D. Popovic, D. E. David, A. J. Nozik, M. A. Ratner, and J. Michl, “Singlet fission for dye-sensitized solar cells: Can a suitable sensitizer be found?” Journal of the American Chemical Society 128, 16546–16553 (2006).pubmed.ncbi.nlm.nih.gov/17177404
  9. [9]⁹K. Ya-Chin, K. Tsu-Jae, and H. Chenming, “Charge-trap memory device fabricated by oxidation of si/sub 1-x/ge/sub x,” IEEE Transactions on Electron Devices 48, 696–700 (2001).DOI
  10. [10]¹⁰H.-W. Lin, W.-Y. Lee, and W.-C. Chen, “Selenophene-dpp donor–acceptor conjugated polymer for high performance ambipolar field effect transistor and nonvolatile memory applications,” J. Mater. Chem. 22, 2120–2128 (2012).DOI
  11. [11]¹¹H. F. Haneef, A. M. Zeidell, and O. D. Jurchescu, “Charge carrier traps in organic semiconductors: a review on the underlying physics and impact on electronic devices,” Journal of Materials Chemistry C 8, 759–787 (2020).DOI
  12. [12]¹²R. A. Street, M. Schoendorf, A. Roy, and J. H. Lee, “Interface state recombination in organic solar cells,” Physical Review B 81, 205307 (2010).DOI
  13. [13]¹³X. Zhan, A. Facchetti, S. Barlow, T. J. Marks, M. A. Ratner, M. R. Wasielewski, and S. R. Marder, “Rylene and related diimides for organic electronics,” Advanced Materials 23, 268–284 (2011).DOI
  14. [14]¹⁴M. Bouhassoune, S. L. M. v. Mensfoort, P. A. Bobbert, and R. Coehoorn, “Carrier-density and field-dependent charge-carrier mobility in organic semiconductors with correlated gaussian disorder,” Organic Electronics 10, 437–445 (2009).DOI
  15. [15]¹⁵R. Coehoorn, W. F. Pasveer, P. A. Bobbert, and M. A. J. Michels, “Charge-carrier concentration dependence of the hopping mobility in organic materials with gaussian disorder,” Physical Review B 72 (2005), 10.1103/PhysRevB.72.155206.DOI
  16. [16]¹⁶G. Chen and Z. Xu, “Charge trapping and detrapping in polymeric materials,” Journal of Applied Physics 106 (2009), 10.1063/1.3273491.DOI
  17. [17]¹⁷H. A. Alghamdi, G. Chen, and A. S. Vaughan, “Simulation of the developed electro-thermal aging model based on trapping and detrapping process,” 10.1109/CEIDP.2015.7352125.DOI
  18. [18]¹⁸H. T. Nicolai, M. M. Mandoc, and P. W. M. Blom, “Electron traps in semiconducting polymers: Exponential versus gaussian trap distribution,” Physical Review B 83 (2011), 10.1103/PhysRevB.83.195204.DOI
  19. [19]¹⁹M. Scheb, C. Zimmermann, and C. Jungemann, “Field-induced detrapping in doped organic semiconductors with gaussian disorder and different carrier localizations on host and guest sites,” Physical Review B 92 (2015), 10.1103/PhysRevB.92.104201.DOI
  20. [20]²⁰J. M. Montero and J. Bisquert, “Interpretation of trap-limited mobility in space-charge limited current in organic layers with exponential density of traps,” Journal of Applied Physics 110 (2011), 10.1063/1.3622615.DOI
  21. [21]Germs, W. C., van der Holst, J. J. M., van Mensfoort, S. L. M., Böttger, B., & Coehoorn, R. (2011). Modeling of the transient mobility in disordered organic semiconductors with a gaussian density of states. Physical Review B, 84. https://doi.org/10.1103/PhysRevB.84.165210
  22. [22]²²A. Miller and E. Abrahams, “Impurity conduction at low concentrations,” Physical Review 120, 745–755 (1960).DOI
  23. [23]²³Y. Lei, P. Deng, M. Lin, X. Zheng, F. Zhu, and B. S. Ong, “Enhancing crystalline structural orders of polymer semiconductors for efficient charge transport via polymer-matrix-mediated molecular self-assembly,” Adv Mater 28, 6687–94 (2016).DOI
  24. [24]LLC, D. (n.d.). DEVSIM TCAD semiconductor device simulator. Retrieved https://devsim.orgdevsim.org
  25. [25]Kimura, T., Nakanishi, K., Nomura, T., Kamiya, T., & Hosono, H. (2008). Trap densities in amorphous-ingazno thin-film transistors. Applied Physics Letters, 92. https://doi.org/10.1063/1.2904704
  26. [26]²⁶H. Xu, W.-J. Zhai, C. Tang, S.-Y. Qiu, R.-L. Liu, Z. Rong, Z.-Q. Pang, B. Jiang, J. Xiao, B. Zhong, Q.-L. Mi, Q.-L. Fan, and W. Huang, “Thickness dependence of carrier mobility and the interface trap free energy investigated by impedance spectroscopy in organic semiconductors,” The Journal of Physical Chemistry C 120, 17184–17189 (2016).DOI
  27. [27]²⁷G. Paasch and S. Scheinert, “Charge carrier density of organics with gaussian density of states: Analytical approximation for the gauss–fermi integral,” Journal of Applied Physics 107 (2010), 10.1063/1.3374475.DOI
  28. [28]Neamen, D. A. (2003). Semiconductor physics and devices. In McGraw-Hill higher education.
  29. [29]Oelrich, J. O., Huemmer, D., & Baranovskii, S. D. (2012). How to find out the density of states in disordered organic semiconductors. Phys Rev Lett, 108, 226403.
  30. [30]³⁰E. Knapp, R. Häusermann, H. U. Schwarzenbach, and B. Ruhstaller, “Numerical simulation of charge transport in disordered organic semiconductor devices,” Journal of Applied Physics 108 (2010), 10.1063/1.3475505.DOI
  31. [31]Boubaker, A., Hafsi, B., Limouni, K., & Kalboussi, A. (2017). A comparative tcad simulations of a p-and n-type organic field effect transistors: field-dependent mobility, bulk and interface traps models. Journal of Materials Science: Materials in Electronics, 28, 7834–7843.
  32. [32]³²S. D. Baranovskii, “Mott lecture: Description of charge transport in disordered organic semiconductors: Analytical theories and computer simulations,” physica status solidi (a) 215 (2018), 10.1002/pssa.201700676.DOI
  33. [33]³³J. Li, Y. Zhao, H. S. Tan, Y. Guo, C. A. Di, G. Yu, Y. Liu, M. Lin, S. H. Lim, Y. Zhou, H. Su, and B. S. Ong, “A stable solution-processed polymer semiconductor with record high-mobility for printed transistors,” Sci Rep 2, 754 (2012).DOI
  34. [34]Ishibashi, T. (1994). Chapter 5 - gaas-based and inp-based heterostructure bipolar transistors. In Semiconductors and Semimetals (Vol. 41, pp. 291–358).
  35. [35]³⁵M. Ghittorelli, T. Lenz, H. Sharifi Dehsari, D. Zhao, K. Asadi, P. W. M. Blom, Z. M. Kovacs-Vajna, D. M. de Leeuw, and F. Torricelli, “Quantum tunnelling and charge accumulation in organic ferroelectric memory diodes,” Nature Communications 8, 15741 (2017).DOI
  36. [36]³⁶“Metal-insulator-semiconductor capacitors,” in Physics of Semiconductor Devices (2006) pp. 197–240.DOI

Paper details

vlnc:W_fa9mpn68
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents