betaFeedback

WorksEngineering

Classical heat exchanger fouling-resistance laws as first-moment identities of additive stochastic deposition

Abstract

Heat-exchanger fouling is monitored through the fouling resistance, whose record is routinely fitted with the classical linear (Ebert–Panchal) or asymptotic (Kern–Seaton) law, and the shape of the fit is often taken as evidence of the underlying deposition or removal mechanism. We show that it cannot be. If the deposit grows by non-negative, statistically stationary increments, the mean fouling resistance is exactly linear without removal and exactly the Kern–Seaton asymptote under first-order removal, whatever the microscopic deposition law. Shear-driven erosion, per-element detachment, intermittent sloughing and saturation of the surface all give the same mean curve, so a fit identifies a net deposition rate and a relaxation time, and nothing else. Modelling the deposit as a Levy subordinator, we show where the missing information lies and what it costs to retrieve it from monitoring data. Removal mechanisms separate in the variance: sloughing leaves a plateau scatter that persists even for smooth deposition and can be read from a record that saturates. Deposition laws separate only in higher cumulants, which the measurement noise of a thermally reconstructed resistance attenuates; the record needed to distinguish them grows as the fourth power of the conductance error, which places it beyond reach at realistic measurement accuracy. For the time to reach a cleaning limit, the deposition law matters only near the threshold; farther away, the mean rate and its uncertainty dominate the prediction.

Introduction

Fouling, the slow accumulation of material at the interface between a flowing phase and a solid, is monitored in heat exchangers through the fouling resistance. Its growth costs fuel, design margin and production lost to cleaning [1, 2, 3], and the operator’s question is when it will reach the limit at which cleaning becomes necessary [4, 5]. In operation the resistance is not measured but reconstructed from temperatures and flow rates through the exchanger’s energy balance [6, 7], so that its change from one sampling period to the next is typically smaller than its measurement error. Decades of work have identified the contributing processes in detail, such as particle transport and attachment, crystallization, chemical reactions and ageing [3, 8, 9, 10]. Fouling records are often still read against two main models, shown in Figure 1. Kern and Seaton assume deposition at a constant rate and removal proportional to the deposit, giving an asymptotic rise to a plateau [11]; Ebert and Panchal set a thermally activated deposition rate against a shear-dependent term, giving a threshold above which the resistance grows linearly [12]. Records are routinely sorted as linear, falling-rate or asymptotic [1, 2, 3, 9], while subsequent work has concentrated on what sets the rate: particle transport and attachment [13, 14, 15, 16, 17, 18], crystallization and wax deposition [19, 20], chemical-reaction fouling [21, 22, 23, 24, 25, 26, 27, 28, 29, 30], ageing [31, 32, 33, 34, 35, 36, 37] and parameter estimation or data-driven prediction from plant data [38, 39, 40, 41]. Replicate fouling runs under identical conditions scatter widely [42], and probabilistic treatments attach this scatter to the deterministic laws as random growth parameters, from which they derive time-to-cleaning distributions and maintenance policies [43, 44, 45, 46]; other stochastic treatments [47, 48, 49, 50] are mostly simulations. None derives the deterministic laws from the stochastic deposition, or asks what the distribution of the fouling measure allows a record to identify.

Prototypical fouling-resistance trajectories showing Kern–Seaton and Ebert–Panchal laws

Figure 1. Prototypical fouling-resistance trajectories. Both laws show an induction period tit_i before the resistance grows, after which the Kern–Seaton law saturates to a plateau R∞R_\infty at a rate set by the removal process, while the Ebert–Panchal law grows approximately linearly once the deposition term dominates.

If fouling reflects many coupled processes, each with its own strong dependence on operating conditions, why do measured trajectories repeatedly collapse onto a small number of elementary shapes? The usual reading is that the shape identifies the dominant mechanism. In heat exchangers an asymptote is read as the signature of removal [51, 52], as the Kern–Seaton derivation suggests, and the saw-tooth pattern and scatter of plant data as evidence of it [53]; yet Ebert and Panchal’s threshold concerns only the initial rate, and linear growth is not evidence that removal is absent [12, 27]. The mechanistic readings have been debated—asymptotic data need not imply removal [1], suppression and removal are indistinguishable during growth [37], and likelihood comparison can select the wrong increment law [54]—but mostly through counterexamples and case studies, not a general statement of what a record can identify.

We show in this study that, under very general conditions, the classical laws are universal first-moment consequences of additive deposition processes. If deposition increments are stationary, independent and non-negative, the deposit is a Lévy subordinator and the two classical laws are first-moment identities: the mean depends only on the net deposition and removal rates, for every additive mechanism. The statement follows directly from the linearity of expectation, but its consequences are not obvious. The information absent from the mean lies in the fluctuations and is unequally accessible: removal mechanisms separate in a plateau variance that survives as the deposition becomes smooth, whereas the increment law separates only in higher cumulants that measurement noise attenuates, turning the noise-free sample size of model selection [54] into a record length that grows as

Nomenclature

Latin symbolsGreek symbols
AAheat-transfer area, m2^2α\alphashape exponent of the event spectrum, Eq. (13)
BBamplitude of the event spectrum, Eq. (13)γ1,γ2\gamma_1,\gamma_2standardized skewness and excess kurtosis of an increment
cccoefficient of variation of the deposit over one sampling period, Eq. (9)γn,k\gamma_{n,k}the same for measured increments over kk periods
c(Δ)c(\Delta)the same over a window Δ\DeltaΔ\Deltawindow length, s
cpc_pspecific heat, J kg−1^{-1} K−1^{-1}ΔT\Delta T, ΔTlm\Delta T_{\mathrm{lm}}temperature change of a stream, log-mean temperature difference, K
D(t)D(t)cumulative deposition, m2^2 K W−1^{-1}ϵ\epsilonrelative random error of the inferred conductance
d′d'separability indexϵj\epsilon_jmeasurement error of reading jj, m2^2 K W−1^{-1}
dpd_pparticle diameter, mζ\zetarelative conductance change per sampling period
EaE_aactivation energy, J mol−1^{-1}η\etafraction of the deposit removed per sloughing event
g(R)g(R)removal law, m2^2 K W−1^{-1} s−1^{-1}θ\thetafractional surface coverage
J1J_1resistance added by one particle, m2^2 K W−1^{-1}κn\kappa_nnnth cumulant
kkwindow length in sampling periodsλ\lambdatempering rate of the event spectrum, m−2^{-2} K−1^{-1} W
kdk_d, krk_rdeposition and removal constantsΛ(t)\Lambda(t)operational clock, Eq. (42)
kfk_fdeposit thermal conductivity, W m−1^{-1} K−1^{-1}μ\mumean fouling resistance, m2^2 K W−1^{-1}
ℓ\ellsize-biased event size, Eq. (11), m2^2 K W−1^{-1}ν(dx)\nu(\mathrm{d}x)Lévy measure (event spectrum), s−1^{-1}
mmmean deposition rate, m2^2 K W−1^{-1} s−1^{-1}ρ\rhonoise-to-signal ratio, Eq. (30)
m˙\dot{m}mass flow rate, kg s−1^{-1}σ\sigmastandard deviation of the measurement error, m2^2 K W−1^{-1}
NNrecord length in sampling periodsτ\tautime lag, s
NeffN_{\mathrm{eff}}, N∞N_{\infty}size-biased events in a window, on the plateauτ0\tau_0sampling period, s
nwn_wnumber of independent windowsτw\tau_wwall shear stress, Pa
nxn_xdistance to the cleaning limit in mean increments, Eq. (37)ϕs\phi_ssolid fraction of the deposit
QQheat duty, Wχ\chirelative deposition intensity
qnq_nnnth cumulant rate, Eq. (6)ψ\psiremoval rate constant, s−1^{-1}
RRfouling resistance, m2^2 K W−1^{-1}
R0R_0, R∞R_{\infty}initial and plateau resistance, m2^2 K W−1^{-1}Subscripts and abbreviations
RgR_guniversal gas constant, J mol−1^{-1} K−1^{-1}cleanclean exchanger
rractivity (total event rate), s−1^{-1}∞\inftyplateau or stationary value
rsr_ssloughing rate, s−1^{-1}kkincrement over kk sampling periods
s2s^2variance rate, m4^4 K2^2 W−2^{-2} s−1^{-1}CVcoefficient of variation
TfT_ffilm temperature, KSNRsignal-to-noise ratio
TxT_xtime to reach the cleaning limit xx, s
tt, tct_c, tit_itime; tc=s2/m2t_c=s^2/m^2; induction time, s
UUoverall heat-transfer coefficient, W m−2^{-2} K−1^{-1}
uuflow velocity, m s−1^{-1}
VVvariance of RR, m4^4 K2^2 W−2^{-2}
w(x)w(x)mass-weighted event spectrum, Eq. (15)
xxcleaning limit, m2^2 K W−1^{-1}
YjY_jmeasured resistance at reading jj, m2^2 K W−1^{-1}

caption:

:::

the fourth power of the noise. The dependence of the rate on operating conditions remains the proper object of mechanistic modelling, but it cannot be inferred from a single record at a single operating point. Section VII translates these results into what an operator can and cannot conclude from a monitored fouling resistance.

Framework and deterministic reference models

Fouling denotes the accumulation or growth of unwanted material on a surface [1, 2, 10]. We describe the state of a fouled surface by a nonnegative fouling measure R(t)R(t), which is kept generic throughout the theory. Its principal application here is the thermal fouling resistance of a heat exchanger, R=1/U−1/UcleanR=1/U-1/U_{\mathrm{clean}} where UU is the overall heat-transfer coefficient. For a homogeneous deposit of thickness δ\delta and thermal conductivity kfk_f this is proportional to the deposit thickness R=δ/kfR=\delta/k_f.

This framework describes deposition under approximately stationary operating conditions in which the deposit does not feed back on the process that creates it. Specifically, we assume that (i) the variables that set the deposition rate (flow, wall shear stress, film temperature, foulant concentration) are constant in time and uniform over the surface, so that RR is an area-averaged scalar; (ii) the deposit does not appreciably change these variables, i.e. the loss of flow cross-section and the resulting changes in wall shear stress and interface temperature are negligible, such feedback being one route to an asymptotic record [55]; (iii) RR is additive in the deposited material, so that ageing, consolidation, and roughness effects that change RR at fixed deposited mass are neglected [32, 56]; and (iv) removal, where present, is a deterministic function of the state. Removal triggered by the deposit state itself (e.g. thickness-dependent spalling) is not treated; Poisson-timed removal of a fixed fraction is (Sec. IV B). Additivity (iii) and the absence of feedback (ii) are what make the mean independent of mechanism; when (i)–(iv) fail, the net rate depends on the state and the mean laws of Table I no longer hold in general, as shown for nonlinear removal in Sec. IV C.

Deterministic fouling models

Fouling is conventionally modeled as a balance between the deposition and removal of material,

dRdt=R˙d−R˙r,(1)\frac{dR}{dt}=\dot{R}_{d}-\dot{R}_{r}, \tag*{(1)}

where R˙d\dot{R}_{d} and R˙r\dot{R}_{r} are the deposition and removal rates in units of RR per unit time. Depending on the relative importance of deposition, adhesion, erosion, and detachment, observed fouling curves may be approximately linear, asymptotic, falling-rate, or irregular [2, 10]. Two prototypical deterministic models used in the industry may provide useful reference limits: the asymptotic (Kern–Seaton) model [11] and the linear (Ebert–Panchal) model [12].

Kern–Seaton. Deposition is proportional to the fluid velocity uu and to the foulant concentration CC, whereas removal grows with the wall shear stress τw\tau_w and with the amount of material already deposited. For particulate fouling, this reads as

R˙d=kduC,R˙r=krτwR,(2)\dot{R}_{d}=k_d uC,\qquad\dot{R}_{r}=k_r\tau_w R, \tag*{(2)}

where kdk_d and krk_r are effective rate coefficients. The clean-surface deposition rate m=kduCm=k_d uC may be interpreted as a mass-transfer-controlled capture rate of classical filtration theory under particulate-fouling assumptions, multiplied

by an attachment efficiency [13, 14]; deposition–removal models of this form for particulate and crystallisation fouling are developed in Refs. [15, 16] and have been a staple of fouling modeling in the industry. The removal law assumes that RR is proportional to the deposited mass, and in fully turbulent flow the wall shear stress is approximately proportional to u2u^2, so that under stationary conditions

dRdt=m−ψR,(3)\frac{dR}{dt}=m-\psi R, \tag*{(3)}

with m=kduCm=k_d uC and ψ=kr′u2\psi=k'_r u^2, where kr′k'_r is krk_r multiplied by the constant of proportionality between τw\tau_w and u2u^2. The fouling resistance then rises monotonically to the plateau R∞=m/ψR_\infty=m/\psi with time constant ψ−1\psi^{-1} [3, 11], and because removal is proportional to RR the state cannot become negative.

Ebert–Panchal. In this family of models the net fouling rate is the difference between a thermally activated deposition contribution and a shear-dependent removal contribution [27]. Following the original derivation

dRdt=aRbexp⁡(−EaRgTf)−γτw≡KEP.(4)\frac{dR}{dt}=aR^{b}\exp\left(-\frac{E_a}{R_gT_f}\right)-\gamma\tau_w\equiv K_{\mathrm{EP}}. \tag*{(4)}

References

  1. [1]N. Epstein, Heat Transfer Engineering 4, 43 (1983).
  2. [2]T. R. Bott, Fouling of Heat Exchangers, Chemical Engineering Monographs, Vol. 26 (Elsevier, Amsterdam, 1995).
  3. [3]H. Müller-Steinhagen, Heat Transfer Engineering 32, 1 (2011).
  4. [4]E. M. Ishiyama, W. R. Paterson, and D. Ian Wilson, Chemical Engineering Science 66, 604 (2011).
  5. [5]T. Pogiatzis, E. M. Ishiyama, W. R. Paterson, V. S. Vassiliadis, and D. I. Wilson, Applied Energy 89, 60 (2012).
  6. [6]R. A. Tatara and G. M. Lupia, International Journal of Engineering, Science and Technology 3, 10.4314/ijest.v3i8.1 (2011).
  7. [7]C. Shen, C. Cirone, and X. Wang, Applied Thermal Engineering 85, 148 (2015).
  8. [8]J. Taborek, T. Aoki, R. B. Ritter, J. W. Palen, and J. G. Knudsen, Chem. Eng. Prog. 68, 59 (1972).
  9. [9]E. F. C. Somerscales, Heat Transfer Engineering 11, 19 (1990).
  10. [10]W. Augustin, L. F. Melo, and D. I. Wilson, Heat and Mass Transfer 61, 72 (2025).
  11. [11]D. Q. Kern and R. E. Seaton, British Chemical Engineering 4, 258 (1959).
  12. [12]W. A. Ebert and C. B. Panchal, in Fouling Mitigation of Industrial Heat-Exchange Equipment, edited by T. R. Bott, L. F. Melo, C. B. Panchal, and E. F. C. Somerscales (Begell House, New York, 1997) pp. 451–460.
  13. [13]K.-M. Yao, M. T. Habibian, and C. R. O’Melia, Environmental Science & Technology 5, 1105 (1971).
  14. [14]N. Epstein, Particulate fouling of heat transfer surfaces: Mechanisms and models, in Fouling Science and Technology (Springer Netherlands, 1988) pp. 143–164.DOI
  15. [15]M. Bohnet, Chemical Engineering & Technology 10, 113 (1987).
  16. [16]M. Kostoglou and A. J. Karabelas, Industrial & Engineering Chemistry Research 37, 1536 (1998).
  17. [17]F. Brahim, W. Augustin, and M. Bohnet, International Journal of Thermal Sciences 42, 323 (2003).
  18. [18]Z. Han, Z. Xu, and X. Yu, International Journal of Heat and Mass Transfer 144, 118428 (2019).
  19. [19]M. Maddahi, M. Hatamipour, and M. Jamialahmadi, International Journal of Thermal Sciences 145, 106017 (2019).
  20. [20]K. Akbarzadeh and M. Zougari, Industrial & Engineering Chemistry Research 47, 953 (2008).
  21. [21]A. Watkinson and D. Wilson, Experimental Thermal and Fluid Science 14, 361 (1997).
  22. [22]E. Rammersdorfer, T. Karner, and M. Siebenhofer, Heat Transfer Engineering 41, 691 (2020).
  23. [23]C. B. Panchal, W. C. Kuru, C. F. Liao, W. A. Ebert, and J. W. Palen, in Understanding Heat Exchanger Fouling and its Mitigation, edited by T. R. Bott, L. F. Melo, C. B. Panchal, and E. F. C. Somerscales (Begell House, 1999) pp. 273–279.
  24. [24]G. T. Polley, D. I. Wilson, B. L. Yeap, and S. J. Pugh, Applied Thermal Engineering 22, 777 (2002).
  25. [25]B. L. Yeap, D. I. Wilson, G. T. Polley, and S. J. Pugh, Chemical Engineering Research and Design 82, 53 (2004).
  26. [26]M. R. J. Nasr and M. M. Givi, Applied Thermal Engineering 26, 1572 (2006).
  27. [27]D. I. Wilson, E. M. Ishiyama, and G. T. Polley, Heat Transfer Engineering 38, 669 (2017).
  28. [28]T. Geddert, I. Bialuch, W. Augustin, and S. Scholl, Heat Transfer Engineering 30, 868 (2009).
  29. [29]M. Mayer, W. Augustin, and S. Scholl, Heat and Mass Transfer 49, 1419 (2013).
  30. [30]J. Yang, International Journal of Heat and Mass Transfer 159, 120129 (2020).
  31. [31]F. Coletti, E. M. Ishiyama, W. R. Paterson, D. I. Wilson, and S. Macchietto, AIChE Journal 56, 3257 (2010).
  32. [32]E. M. Ishiyama, W. R. Paterson, and D. Ian Wilson, AIChE Journal 57, 3199 (2011).
  33. [33]E. M. Ishiyama, W. R. Paterson, and D. I. Wilson, Heat Transfer Engineering 35, 311 (2013).
  34. [34]F. Coletti and S. Macchietto, Industrial & Engineering Chemistry Research 50, 4515 (2011).
  35. [35]E. Diaz-Bejarano, F. Coletti, and S. Macchietto, AIChE Journal 62, 90 (2015).
  36. [36]F. Coletti, B. Crittenden, and S. Macchietto, Basic science of the fouling process, in Crude Oil Fouling (Elsevier, 2015) pp. 23–50.DOI
  37. [37]E. Diaz-Bejarano, F. Coletti, and S. Macchietto, Heat Transfer Engineering 38, 681 (2017).
  38. [38]J. Loyola-Fuentes, M. Jobson, and R. Smith, Industrial & Engineering Chemistry Research 58, 10418 (2019).
  39. [39]J. Loyola-Fuentes and R. Smith, Energy 183, 68 (2019).
  40. [40]M. Markowski and P. Trzcinski, Scientific Reports 15, 42078 (2025).
  41. [41]Y. Sundar, M. C. Rajagopal, H. Zhao, G. Kuntumalla, Y. Meng, H. C. Chang, C. Shao, P. Ferreira, N. Miljkovic, S. Sinha, and S. Salapaka, International Journal of Heat and Mass Transfer 159, 120112 (2020).
  42. [42]S. M. Zubair, A. K. Sheikh, M. O. Budair, M. U. Haq, A. Quddus, and O. A. Ashiru, Journal of Heat Transfer 119, 581 (1997).
  43. [43]S. M. Zubair, A. K. Sheikh, and M. N. Shaik, Energy 17, 769 (1992).
  44. [44]S. M. Zubair, A. K. Sheikh, M. O. Budair, and M. A. Badar, Journal of Heat Transfer 119, 575 (1997).
  45. [45]S. M. Zubair, A. K. Sheikh, M. Younas, and M. O. Budair, Energy 25, 427 (2000).
  46. [46]A. K. Sheikh, S. M. Zubair, M. Younas, and M. O. Budair, Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering 215,
  47. [47]N. Vatistas, Stochastic model for the induction step on particulate fouling, in Fouling Science and Technology (Springer Netherlands, 1988) pp. 165–171.DOI
  48. [48]J. R. Flora, Journal of Membrane Science 76, 85 (1993).
  49. [49]M. Wessling, Separation and Purification Technology 24, 375 (2001).
  50. [50]J. Liu, T. Huang, R. Ji, Z. Wang, C. Y. Tang, and J. O. Leckie, Environmental Science & Technology 54, 12703 (2020).
  51. [51]K. Shaikh, K. M. S. Newaz, M. N. M. Zubir, K. H. Wong, W. A. Khan, S. Abdullah, M. S. Alam, and L. Sugumaran, Journal of Thermal Analysis and Calorimetry 10.1007/s10973-023-12544-z (2023).
  52. [52]A. Fuguiri, R. Jradi, C. Marvillet, and M. R. Jeday, Heat and Mass Transfer 10.1007/s00231-020-02858-1 (2020).
  53. [53]B. D. Crittenden, S. T. Kolaczkowski, and I. L. Downey, Trans. ChemE, Part A, Chem. Eng. Res. Des. 70, 547 (1992).
  54. [54]M. Zhang and M. Revie, in Risk, Reliability and Safety: Innovating Theory and Practice (Proceedings of ESREL 2016) (CRC/Taylor & Francis, London, 2016).
  55. [55]O. u. Rehman, M. G. Ramasamy, N. E. Mohammad Rozali, S. Mahadzir, A. S. M. Ghumman, and A. H. Qureshi, Processes 11, 1036 (2023).
  56. [56]B. Crittenden and N. Alderman, Chemical Engineering Science 43, 829 (1988).
  57. [57]K.-i. Sato, Lévy Processes and Infinitely Divisible Distributions, Cambridge Studies in Advanced Mathematics, Vol. 68 (Cambridge University Press, Cambridge, 1999).
  58. [58]D. Applebaum, Lévy Processes and Stochastic Calculus, 2nd ed., Cambridge Studies in Advanced Mathematics, Vol. 116 (Cambridge University Press, Cambridge, 2009).
  59. [59]N. Campbell, Proceedings of the Cambridge Philosophical Society 15, 117 (1909).
  60. [60]J. Rosiński, Stochastic Processes and their Applications 117, 677 (2007).
  61. [61]B. Jørgensen, Journal of the Royal Statistical Society Series B: Statistical Methodology 49, 127 (1987).
  62. [62]P. Hougaard, Biometrika 73, 387 (1986).
  63. [63]M. Abdel-Hameed, IEEE Transactions on Reliability R-24, 152 (1975).
  64. [64]J. Lawless and M. Crowder, Lifetime Data Analysis 10, 213 (2004).
  65. [65]J. van Noortwijk, Reliability Engineering & System Safety 94, 2 (2009).
  66. [66]J. D. Esary, A. W. Marshall, and F. Proschan, The Annals of Probability 1, 627 (1973).
  67. [67]W. Wang and D. Xu, Technometrics 52, 188 (2010).
  68. [68]Z.-S. Ye and N. Chen, Technometrics 56, 302 (2014).
  69. [69]Z.-S. Ye and M. Xie, Applied Stochastic Models in Business and Industry 31, 16 (2015).
  70. [70]X.-S. Si, W. Wang, C.-H. Hu, and D.-H. Zhou, European Journal of Operational Research 213, 1 (2011).
  71. [71]W. Kahle, S. Mercier, and C. Paroissin, Degradation Processes in Reliability (Wiley, 2016).DOI
  72. [72]E. Çinlar, Shock and wear models and Markov additive processes, in The Theory and Applications of Reliability with Emphasis on Bayesian and Nonparametric Methods (Elsevier, 1977) pp. 193–214.
  73. [73]M. Abdel-Hameed, Mathematics of Operations Research 9, 606 (1984).
  74. [74]Y. Shu, Q. Feng, E. P. Kao, and H. Liu, IIE Transactions 48, 993 (2016). P. Collett, A. J. Stasik, S. Casolo, and S. Riemer-Sørensen, Fast Bayesian equipment condition monitoring via simulation based inference: applications to heat exchanger health, arXiv preprint (2026), arXiv:2604.20735 [cs.LG].
  75. [76]O. E. Barndorff-Nielsen and N. Shephard, Journal of the Royal Statistical Society Series B: Statistical Methodology 63, 167 (2001).
  76. [77]P. S. Stewart, Biotechnology and Bioengineering 41, 111 (1993).
  77. [78]A. Bohn, B. Zippel, J. Almeida, and J. Xavier, Water Science and Technology 55, 257 (2007).
  78. [79]W. R. Paterson and P. J. Fryer, Chem. Eng. Sci. 43, 1714 (1988).
  79. [80]S. O. Rice, Bell System Technical Journal 23, 282–332 (1944).
  80. [81]S. O. Rice, Bell System Technical Journal 24, 46–156 (1945).
  81. [82]M. D. Penrose, Communications in Mathematical Physics 218, 153 (2001).
  82. [83]E. S. Loscar, R. A. Borzi, and E. V. Albano, Physical Review E 68, 041106 (2003).
  83. [84]H. Nakagawa and I. Nezu, Memoirs of the Faculty of Engineering, Kyoto University 40, 213 (1978).
  84. [85]F. Miele, A. D. Bordoloi, M. Dentz, H. Tabuteau, V. L. Morales, and P. de Anna, arXiv preprint arXiv:2505.02689 (2025).arxiv.org/abs/2505.02689
  85. [86]G. A. Whitmore, Lifetime Data Analysis 1, 307 (1995).
  86. [87]L. Bordes, C. Paroissin, and A. Salami, Communications in Statistics - Theory and Methods 45, 2730 (2015).
  87. [88]G. Pulcini, Reliability Engineering & System Safety 152, 296 (2016).
  88. [89]Y. Lanoiselée, D. S. Grebenkov, G. Sikora, A. Grzesiek, and A. Wyłomańska, Physical Review E 98, 062139 (2018), arXiv:1808.00412.DOI
  89. [90]R. Al Ismaïli, M. W. Lee, D. I. Wilson, and V. S. Vassiliadis, Computers & Chemical Engineering 121, 409 (2019).
  90. [91]A. Di Pretoro, F. D’Iglio, and F. Manenti, Processes 9, 93 (2021).
  91. [92]S. Zacks, Journal of Statistical Planning and Inference 130, 95 (2005).
  92. [93]Z. Chi, Stochastic Processes and their Applications 126, 1124 (2016).
  93. [94]J. I. González Cázares, F. Lin, and A. Mijatović, Stochastic Systems 15, 50 (2025).
  94. [95]G. R. Bolton, A. W. Boesch, and M. J. Lazzara, Journal of Membrane Science 279, 625 (2006).
  95. [96]M. Cifuentes-Cabezas, J. L. Bohórquez-Zurita, S. Gil-Herrero, M. C. Vincent-Vela, J. A. Mendoza-Roca, and S. Álvarez-Blanco, Food and Bioprocess Technology 16, 2126 (2023).
  96. [97]P. Singh, R. Venkatesan, H. S. Fogler, and N. Nagarajan, AIChE Journal 46, 1059 (2000).
  97. [98]A. K. Mehrotra, S. Haj-Shafiei, and S. Ehsani, Journal of Pipeline Science and Engineering 1, 428 (2021).

Paper details

vlnc:W_fc2453sg
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Engineering

Not recorded for this paper

View statement
Looking for related papers…
Contents