betaFeedback

WorksPhysics and Astronomy

Strain Engineering on the Excitonic Properties of Monolayer GaSe

Abstract

This paper investigates strain effects on the electronic and optical properties of monolayer GaSe using first-principles calculations. The deformation significantly alters energy dispersion, band gap, and the band edge states of GaSe. The band gap evolution exhibits both linearly and nonlinearly with the strains, and strongly depending on the types of deformation and the direction of the modifications. The external mechanical strains also significantly tailor the optical properties of GaSe, the exciton binding energy is strongly reduced when the tensile strain is applied, while the opposite way is true for compressive stress. Moreover, the inhomogeneous strain also induces strong polarization in the absorption spectra. Our calculations demonstrate that the electronic and optical properties of GaSe monolayer can be significantly tuned by using strain engineering which appears as a promising way to design novel optoelectronic devices.

*Corresponding authors: [email protected] and [email protected]

Introduction

The study of atomically thin two-dimensional (2D) has become one of the mainstream research topics of condensed matter physics due to the fascinating properties and practical applications of these materials [1, 2, 3]. The pursuit of tailoring electronic and optical properties in 2D crystals, in particular, has remained a goal in this area [4, 5, 6]. The modulations of the electronic and optical properties of 2D crystals can be established by introducing adatoms [7, 8], defects [8], mechanical deformation [9, 10], and external electric fields or magnetic fields [11, 12, 13, 14]. Among these, strain engineering is well-known for being a useful and flexible technology to tailor material features for a variety of applications [15, 16]. For example, atomically thin carbon atoms - graphene can withstand up to 20% strain [17]. Moreover, accurate first-principles calculations predict that the broken symmetry of layered graphene under uniaxial strain induced an anisotropic Fermi velocity, significantly altering the optical properties as well as the excitonic effects [18, 19]. These findings imply that modulating the electronic structure and optical properties of graphene and other 2D systems is flexible.

A new class of 2D crystals, the atomic thins of group III-VI compounds (MXMX, M=GaM = \mathrm{Ga}, In, X=SX = \mathrm{S}, Se, Te) have presently received a lot of attention [20, 21, 22] due to their interesting properties and their widespread use in high-harmonic generations [23, 24], optoelectronic [25, 26, 27], photovoltaics [28, 29], and photocatalytic water splitting [30, 31]. Similar to graphene, the adjacent layer of MX is weakly held together through very weak Val-der-Wall interactions, whereas the rather strong ionic interactions are dominated by the chemical bonding between post-transition metal and chalcogenide atoms in an intralayer MX. This distinctive feature enables to cleavage of this material into a single layer via mechanical exfoliation [32, 33]. In addition, these materials can also be thinned down to the layered of the event monolayer form using other techniques. For example, a monolayer of GaSe has been successfully fabricated on the difference subtracts using chemical vapor depositions and/or molecular beam epitaxy [34, 35, 36].

According to earlier theoretical and experimental investigations, the direct-to-indirect band gap transition occurred in GaSe when the number layer is decreased below the critical value [37, 38], which is an inverse tendency of transition metal dichalcogenides [39]. In particular, up to the layer limit of 7, the lowest unoccupied state is still the parabolic sharp at the Γ\Gamma point. In the contract, the significantly down-shift of the highest occupied state vicinity of the Γ\Gamma point leads to a Mexican hat-sharp energy band surface around the zone center [37]. In addition to the electronic properties, layered GaSe may exhibit unique and extraordinary excitonic effects. Gallium selenide has demonstrated strong photoresponse in recent experiments [40]. The theoretical prediction of Antonius and his co-workers indicated that the absorbance spectra of GaSe exhibit feature exciton peaks with distinct polarization selectivity, such interesting phenomena come from the symmetry of the bands under in-plane mirror symmetry [41].

Up to now, there are several works have been done to investigate the effects of mechanical modulation on the stability and electronic properties of monolayer or bulk GaSe. For example, the theoretical work of Yagmurcukardes et. al has shown that such materials can be stable up to ∼\sim17% homogenous strain [42]. In addition, Z. Zhu et al predict that appropriate strain engineering can induce the Topological phase transition in layer GaSe [21]. Although these studies have been proposed inside into the effects of strain engineering; however, information about the strain effects on fundamental properties of GaSe monolayers cannot be achieved: (i) the critical mechanism, the close connection between the orbital interactions and band gap modulations has not been clarified. (ii) Changing the electronic band gap directly affects the electronic screening, many-electrons interactions in materials, and thus the excitonic effects. Studying GaSe under strain allows us to observe how the excitonic properties of deformed 2D materials to those of pristine materials. However, according to our knowledge, the delicate analysis of the inhomogeneous and homogenous strains on the optical properties and excitonic effects of group III-VI monolayers has not been established up to now.

In this work, based on the accurate first-principles density functional theory (DFT) [43] and many-body perturbation theory [44], the quasi-particle energies and the optical excitations with and without exciton effects could be obtained. By the delicate connections of the optimal geometric structure with the position-dependent chemical bonding, the band edge states in the electronic band structure, the van Hove singularities in density of states, the optical absorbance spectra with includes the excitonic effects, and the exciton wave functions, the concise picture of inhomogeneous and homogeneous strain effects could be achieved. Particularly, these strain-induced various absolute band-edge energies and exciton states may accommodate optical excitations for light emission or photo-voltaic applications.

Computational details

Vienna Ab-initio Simulation Package (VASP) [45] was utilized to perform the ground state and the excited state calculations of the GaSe monolayer.

Ground states calculations

The Perdew-Burke-Ernzerhof (PBE) generalized gradient approximation [46] was adopted for the exchange-correlation function. Projector-augmented wave (PAW) pseudopotentials are utilized to characterize the electronic wave functions in the core region [47]. The cutoff energy for the expansion of the plane wave basis was set to 500 eV. The Brillouin zone was integrated with a special kk-point mesh of 35×35×135 \times35 \times1 in the Monkhorst-Pack sampling technique [48] for geometric optimization. The convergence condition is set to be 10−810^{-8} eV between two consecutive simulation steps, and all atoms were allowed to fully relax during geometric optimization until the Hellmann-Feynman force acting on each atom was smaller than 0.010.01 eV/A˚\mathrm{\AA}.

Quasiparticles calculations

On top of Kohn Sham wave functions and the corresponding eigenvalues of the DFT level, the single-particle Green’s function and the screened Coulomb interactions approach (G0W0) [49] were applied to get the exact electronic properties as well as wave functions for excitonic calculations. The plasmon-mode model of Hybertsen and Louie [49] was utilized to describe the screening effects. To ensure the accuracy of the calculations, we established convergence tests with various kk-mesh and the Cutoff energy for the response functions. The calculated results (Figure S1) indicated that KPOINTS of 40×40×140 \times40 \times1 and 130 eV for cutoff energy for response functions could give an adequate convergence for the quasiparticle band gap. These convergence parameters were used for all calculations of electronic and optical properties in this paper.

Optical properties and excitonic effects

Under the incidence of photons, the electrons in the occupied states will be vertically excited to the unoccupied ones in the quasiparticle energy spectra without carrying any crystal momentum transfer. According to Fermi’s golden role [50], the probability of single-particle excitations can be expressed using the imaginary part of dielectric functions:

ϵ2(ω)=8π2e2ω2∑vck∣e⋅⟨vk∣v∣ck⟩∣2δ(ω−EckQP−EvkQP)\epsilon_{2}(\omega) = \frac{8\pi^{2}e^{2}}{\omega^{2}} \sum_{vck} \lvert e \cdot\langle vk \lvert v \rvert ck \rangle\rvert^{2} \delta\left(\omega- E_{ck}^{QP} - E_{vk}^{QP}\right)

where the intensity of each excitation peak and the available transition channels are directly related to the velocity matrix element, ∣e⋅⟨vk∣v∣ck⟩∣2\lvert e \cdot\langle vk \lvert v \rvert ck \rangle\rvert^{2}, and joined of the density of states δ(ω−EckQP−EvkQP)\delta\left(\omega- E_{ck}^{QP} - E_{vk}^{QP}\right), respectively.

Regarding the optical response beyond the independent particle approach, the electron-hole interactions were taken into account. The connection of the exciton energies ΩS\Omega_{S} and corresponding electron-hole amplitude ∣e⋅⟨0∣v∣S⟩∣2\lvert e \cdot\langle0 \lvert v \rvert S \rangle\rvert^{2} of the correlated electron-hole excitations SS is obtained by solving the Bethe-Salpeter equation (BSE) [50]:

(EckQP−EvkQP)AvckS+∑v′c′k′⟨vck∣Keh∣v′c′k′⟩Av′c′k′S=ΩSAvckS\left(E_{ck}^{QP} - E_{vk}^{QP}\right) A_{vck}^{S} + \sum_{v'c'k'} \langle vck \lvert K^{eh} \rvert v'c'k' \rangle A_{v'c'k'}^{S} = \Omega^{S} A_{vck}^{S}

where, KehK^{eh} is the kernel describing the correlated electron-hole pairs, EckQPE_{ck}^{QP} and EvkQPE_{vk}^{QP}, respectively, are the excitation energies for the conduction band states and the valence band states, and ΩS\Omega^{S} is the energy of the excited state. In this calculation, the 6 highest occupied valence bands (VBs) and 4 lowest unoccupied conduction bands (CBs) are included as a basis for the excitonic states with a photon energy region from 0 eV to 5 eV. In addition, the Lorentz broadening parameter Γ\Gamma was set at 50 meV to replace the delta function.

Results and discussions

Geometric and electronic properties

We begin our investigation of the GaSe monolayer by looking at its geometric properties. The unit cell of single-layer GaSe contains four atoms (2 Ga and 2 Se). The Ga and Se atoms are connected by a very strong covalence bond in the order Se-Ga-Ga-Se, resulting in a trigonal prismatic arrangement. Similar to graphene, the top view of the GaSe monolayer also exhibits a hexagonal structure, and thus, its first Brillouin zone (FBZ) is also an equilateral hexagon. The predicted layer structure and the atom ordering of GaSe, which includes a highly anisotropic and non-uniform environment, agree well with the available experimental examinations [23, 51]. The homogenous strain (H-strain) could be achieved by uniform modulation of the lattice constant during structural relaxation. Similarly, to investigate single-layer GaSe with an asymmetric strain distribution parallel to armchair direction (A-strain) or zigzag direction (Z-strain), the deformed primitive cell along the armchair or zigzag direction with a fixed lattice constant of zigzag or armchair direction is required. Under a homogeneous (inhomogeneous) strain, single-layer GaSe retains (breaks) its hexagonal symmetry, thereby preserving (destroying) the hexagonal FBZ (Figure 1(a-Figure 1c)).

Structure and the FBZ of single layer GaSe

Figure 1. Structure and the FBZ of single layer GaSe. The three types of strains on monolayer GaSe and its corresponding FBZ are shown: (a) the compressive and tensile H-, (b) A-, and (c) Z-strains.

The delicate analysis of the Se-Se height difference, Ga-Se, and Ga-Ga bond lengths under different compressive and tensile strains could provide a general picture of the strain-created deformations in monolayer GaSe. According to Figure 2(a-Figure 2d), the modulations are in the following order: H-strain > A-strain ≥ Z-strain. Overall, the chemical modifications of in-plane (Ga-Se chemical bonding) and out-of-plane (Se-Se height difference) show opposite manners. The length of the Ga-Se bond increases (decreases) isotopically under tensile strain (compressive strain), the opposite trend is true for out-of-plane parameters of Se-Se height difference. The Ga-Ga chemical bonding remains almost constant under external mechanical perturbations. Although we have fixed the lattice constant along the unstrained directions, the Ga-Se bond lengths along these directions also present a slight modulation under the inhomogeneous modulations due to the Poisson effects [42, 52]. The significant chemical modifications discussed here will be directly related to the overlaps or separations of orbitals and thus, related to the modifications of electronic and optical properties.

Plots of Ga–Se bond length, Ga–Ga bond length, Se–Se height difference, and geometric structure of GaSe monolayer

Figure 2. (a) The Ga-Se, (b) Ga-Ga bond lengths, and (c) the Se-Se height differences of GaSe monolayer under homogeneous/inhomogeneous strains. (d) Manifesting the geometric structure of GaSe monolayer.

Figure 3a depicts the electronic band structure of the GaSe monolayer. The electronic structure of GaSe has been investigated using both DFT and GW approximations, the spin-orbit coupling (SOC) is weak so it has been neglected in current calculations. The DFT level of theory indicates that the GaSe monolayer possesses an indirect gap of 1.655 eV. When the GW approximation is used, the electronic band gap increases to 3.45 eV. This value is consistent with recent GW calculations [42, 53, 54] and the STS measurement [55]. The characteristic of energy band dispersions includes the conduction band minima (CBM) C1_1 and the parabolic relation C2_2 at the Γ\Gamma and K points, respectively. The highest occupied state presents a Mexican hat-sharp dispersion V1_1 with its valence band maxima (VBM) located between Γ\Gamma and K. The energy difference between Γ\Gamma and VBM is about 0.125 eV, due to this large difference, the photoluminescence disappearance in the GaSe monolayer and other group III-VI monolayers [56]. Beyond the V1_1 energy dispersion, the energy band structure of GaSe also be featured by two double-degeneracy V2_2 and V3_3, these energy bands mostly present parabolic energy dispersions. In the occupied states, the energy dispersion below the Fermi level is in good agreement with the measurement of Angle-Resolved Photoemission Spectroscopy (ARPES) as shown in Figure S2 [57].

Electronic band structure and band-decomposed charge density of GaSe monolayer

Figure 3. (a) The electronic band structure of GaSe monolayer along high symmetry points with different levels of theory. The red and black lines, respectively, indicate the GW and DFT approximations. (b) Band decomposed charge density for certain critical points in valence and the conduction bands as

Ga-Ga (Å)Ga-Se (Å)Se-Se (Å)Eg(eV)E_g (eV)
2.470a2.470^{a}2.497a2.497^{a}4.818a4.818^{a}1.655a/3.446b1.655^{a}/3.446^{b}
2.47c2.47^{c}-4.82c4.82^{c}1.83c/2.71d1.83^{c}/2.71^{d}
2.470e2.470^{e}2.501e2.501^{e}4.827e4.827^{e}2.252e2.252^{e}
2.474f2.474^{f}2.5f2.5^{f}-1.83f1.83^{f}
-2.47g2.47^{g}4.82g4.82^{g}2.18g/3.68h2.18^{g}/3.68^{h}
---2.0i/3.7j2.0^{i}/3.7^{j}
---2.10k/3.94l2.10^{k}/3.94^{l}
---3.5m3.5^{m}

Table 1. The optimize geometric parameters and the electronic band gap of monolayer GaSe. The previous theoretical and experimental values are also shown for comparison.

The orbital-projected band structure could provide a partly information to understand the nature of electronic wave functions (Figure 3c and Figure 3d). The delicate analysis of the orbital characteristics reveals that V1_1, and V2_2 + V3_3 energy sub-bands, correspondingly, associate with (Ga-4pz_z, Se-4pz_z), and (Ga-(4px_x, 4py_y), Se-(4px_x, 4py_y)) orbitals. The features of (Ga-4s, Se-4pz_z) and (Ga-(4px_x, 4py_y), Se-(4px_x, 4py_y)) orbitals are presented in the C1_1 and C2_2 states in the conduction bands, respectively. For better insight, we also calculate the band-decomposed charge density of C1_1, C2_2, V1_1, and V2_2 + V3_3 energy sub-bands. As seen in Figure 3b, these sub-bands display very different spatial charge densities when compared to one another. The V1_1 energy sub-band which dominated by the out-of-plane component of (Ga-4pz_z, Se-4pz_z), the V2_2 + V3_3 energy sub-bands belong to the in-plane charge density distribution of (Ga-(4px_x, 4py_y), Se-(4px_x, 4py_y)), both of them present the bonding properties. While the opposite is true for C1_1 and C2_2 states, these sub-bands present the anti-bonding features of (Ga-4s, Se-4pz_z) density, and in-plane characters of (Ga-(4px_x, 4py_y), Se-(4px_x, 4py_y)) electronic density, respectively. Such identifications could be useful in explaining the band gap evolutions.

described in (a). The orbital projected electronic band structure for (c) Gallium atom, and (d) Selenium atom.

The modulations of the electronic band structure for GaSe upon strain are shown in Figure 4. Concerning uniform compression, the conduction energy dispersion C2C_2 and the degeneracy parabolic V2+V3V_2 + V_3 valence sub-bands move forward to the Fermi level as a result of the Ga-(4px4p_x, 4py4p_y) and Se-(4px4p_x, 4py4p_y) orbitals overlap (resulting of Ga-Se chemical bond length decreasing). The opposite way is true for parabolic C1C_1 and Mexican hat-sharp dispersion V1V_1. Apparently, at a certain strain, the indirect-direct transition under the valence band inversion could be achieved. In the inverse process, the tensile strain induces the valence band V1_1 and the conduction band C1_1 to be close to each other by increasing of interactions of two-opposite Se-4pz_z orbitals (resulting of Se-Se height difference decreasing). Similar manners are also observed in non-uniform modulations. Very interestingly, the Mexican hat-sharp dispersion V1_1 and the degenerate sub-bands V2_2 and V3_3 are either right-shift, left-shift, or vanish, and thus, the anisotropic energy band structure becomes more apparent. Furthermore, the presence of additional band edge states in specific wave-vector spaces, such as R or S points, may induce strong Van Hove singularities in the density of states, resulting in extra optical excitations.

DFT electronic band gap of monolayer GaSe under homogeneous, armchair, and zigzag strains

Figure 4. The DFT electronic band gap of monolayer GaSe under (a) – (b) homogeneous strains, (c) – (d) armchair strains, and (e) – (f) zigzag strains.

Figure 5 depict the bandgap of a GaSe monolayer as a function of external strains. It is worth noting that the bandgap adjustments for compression and elongation are significantly different. As the interactions between the atoms in the unit cell change, the energy band gap also changes significantly. Because the interaction between Ga-Se decreases with increasing H-strain, the band gap decreases linearly. The evolution of the gap for homogeneous compressive strain is more complicated; for example, it shows a slight increase to EgDFT=2.106E_g^{DFT} = 2.106 eV/EgGW=3.803E_g^{GW} = 3.803 eV and then monotonically decreases when higher strains are applied, which is due to the bottom of the conduction band transfers among several high symmetry points, such as Γ\Gamma point at 0% strain, M point at -4% strain, and K point at -10% strain. Apparently, under a critical strain, the semiconductor-metallic transition could be achieved as has been illustrated in previous investigations [42]. The band gap evolution for A-strain and Z-strain also exhibits a similar tendency. However, due to the weaker atomic interactions, they present a smaller modulation. These behaviors are similar to those of monolayer MoS2_2 [60, 61] and in good agreement with previous work [52].

Band gap evolution of GaSe monolayer under homogeneous strain, armchair strain, and zigzag strain

Figure 5. The band gap evolution of GaSe monolayer under homogeneous strain, armchair strain, and zigzag strain. The label k∗k^* (k=Γk = \Gamma, M, K) denotes the minimum point of the conduction band, which is located at the side of the k point.

Optical properties and excitonic effects

When the GaSe monolayer presents under the electromagnetic wave (EM), the electron will be vertically excited from the occupied states to the unoccupied ones due to the conservation of energy and momentum. The picture of the optical excitation could be well characterized by Fermi’s golden rule, in which the prominence peaks in absorption spectra directly reflect the features of the electronic band structure. Beyond the single-particle picture, the mutual Coulomb interactions of the excited electron and the excited hole (excitonic effects) will significantly alter the optical absorbance spectrum, e.g., inducing the red-shift of the optical gap, and enhancement of the optical excitations [62, 63, 64, 65]. Atomic thin 2D GaSe is expected to have strong and special excitonic effects owing to two important factors: (i) weak dielectric screening due to large quasiparticle band gap and the absence of vertical electronic screenings, (ii) quantum confinements make the excited electrons and excited holes closer. These well-defined factors will be responsible for the formation of excitonic resonances or robust exciton bound-states with remarkable binding energies. The composite effects of external strains and electron-hole interactions on the optical properties of the GaSe monolayer will be discussed in detail in the current work.

Figure 6a shows the imaginary part of the dielectric functions (ϵ2(ω)\epsilon_{2}(\omega)) of the pristine GaSe, the solid curve indicates the absorbance spectra with include the electron-hole interactions, while the dashed curve excludes these effects. Because of the symmetric of the geometric structure, the optical absorption of the GaSe monolayer is non-degenerate. The absorbance spectra in the absence of the excitonic effects in the low-frequency domain present the like-step functions, which are characteristic of two-dimensional systems with parabolic energy sub-bands. When the electron-hole interactions have been taken into account, we found two prominent bright exciton states (EXn=1E_{X}^{n=1}, EXn=2E_{X}^{n=2}) located below the fundamental band gap, such exciton states could be assigned to the mutual coupling of the V2_2 + V3_3 valence holes with C1_1 conduction electrons at Γ\Gamma point, and the V1_1 valence holes with C2_2 conduction electrons at the saddle point located between Γ\Gamma and M high-symmetry direction, respectively (Figure 6c). The exciton binding energy (ExbE_{xb}), which can be evaluated by the energy difference between the first bright exciton energy (EXn=1E_{X}^{n=1}) and the corresponding direct transition energy is about 0.48 eV, the great red shift indicates the very strong Coulomb couplings between two opposite charges, and the composite quasiparticles in GaSe should be quite stable and comparable with other 2D systems as graphone (~0.6 eV) [66], and transition metal dichalcogenides (~1.0 eV) [67, 68]. The theoretical prediction in this work is relatively in good accordance with the previous photoluminescence measurements [27] and theoretical calculations [41].

Optical properties of the strainless GaSe monolayer

Figure 6. The optical properties of the strainless GaSe monolayer. (a) indicates the imaginary parts of dielectric functions ε2(ω)\varepsilon_{2}(\omega) with include (solid curves) and exclude (dashed-curves) the excitonic effects. (b) shows the energy spectrum of the bound excitons. (c) indicates the amplitude of the darkness DXn=1D_{X}^{n=1} and the first bright EXn=1E_{X}^{n=1} excitons. The radii of the circles represent the contribution of electron-hole pairs at the k-point to the ith exciton wave function.

Figure 6b shows the energy levels of the bound excitons in the GaSe monolayer including dark and bright types. Similar to other two-dimensional materials such as MoS2_2 [69] and phosphorus [70], the exciton levels do not follow the hydrogenic Rydberg series as a result of the spatially varying screening. Even though lacking any spectral signature in the optical spectra, the dark excitons still play a significant role in understanding the optical fingerprint and the dynamics in low-dimensional materials [71]. Our calculations indicated that at least one dark exciton state is located below the first bright exciton. The minimum energy to trigger this dark state is 3.27 eV, which is 0.29 eV smaller than the required by photoexcitation. The dark exciton state with zero dipole moment for the in-plane light polarization could be understood as the forbidden transition of the opposite-parities valence band V1_1 and the conduction band C1_1 at the Γ\Gamma center [41]. The characteristics of the bright and dark excitons are strongly modulated with the angle of the incident light as has been reported in previous work [41].

The optical excitation of GaSe under biaxial strain is shown in Figure 7(a-Figure 7b) and Figure 7(c-Figure 7d), the optical gap in the absence of electron-hole interactions is reduced due to the reduction of the electronic band gap. When the excitonic effects are taken into account, the energy of prominence excitations and their intensity alter dramatically. The most prominent feature is that the exciton binding energy of GaSe under tensile strain is weak and incomparable with the strainless and the compression. The main reasons for this interesting property are due to the enhancement of the screening ability (increasing of static dielectric constant ϵ1(0)\epsilon_{1}(0) as shown in Table 2 or reduction of the electronic band gap and the separation of the electron and hole states. Thanks to the opposite band inversions of V1_1 and V2_2 sub-bands, the exciton spectra of GaSe monolayer under tensile and compressive strains show the opposite manner, there are more dark exciton states below the first bright exciton EXn=1E_{X}^{n=1} for the lattice expansions, while in the opposite case, the lowest exciton state belongs to the bright one.

Optical properties of the GaSe monolayer under different strain conditions

Figure 7. The optical properties of the GaSe monolayer under (a)–(b) H = −10%-10\%, (c)–(d) H = +10%+10\%, (e)–(f) A = −10%-10\%, (g)–(h) A = +10%+10\%, (i)–(j) Z = −10%-10\%, (k)–(l) Z = +10%+10\%. The top Figure indicates the imaginary parts of dielectric functions ε2(ω)\varepsilon_{2}(\omega) with include (solid curves) and exclude (dashed-curves) the excitonic effects. The bottom Figure shows the energy spectrum of the bound excitons.

Strain (%)H-strainA-strainZ-strain
ExbE_{xb}ε1(0)\varepsilon_{1}(0)ExbE_{xb}ε1a(0)\varepsilon_{1}^{a}(0)ε1z(0)\varepsilon_{1}^{z}(0)ExbE_{xb}ε1a(0)\varepsilon_{1}^{a}(0)ε1z(0)\varepsilon_{1}^{z}(0)
-100.4884.0160.4833.8183.9590.4823.9713.809
-80.4933.9270.4853.7893.9080.4833.9113.785
-60.4923.8550.4833.7773.8670.4853.8683.775
-40.4923.8290.4853.7803.8380.4853.8413.778
-20.4873.8020.4843.7863.8130.4853.8143.786
00.4823.7990.4823.7993.7990.4823.7993.799
+20.4743.8210.4763.8243.7920.4783.7923.825
+40.4643.8780.4723.8633.7940.4723.7973.862
+60.4533.9730.4673.9173.8110.4663.8173.913
+80.4374.1030.4593.9903.8410.4593.8483.977
+100.4154.2920.4514.0733.8820.4513.8934.057

Table 2. The evolutions of the exciton binding (ExbE_{xb}), and the dielectric constant (ε1(0)\varepsilon_{1}(0)) under the homogeneous, armchair, and zigzag strains.

The optical absorbance spectra of GaSe under armchair strain are presented in Figure 7(e-Figure 7f) and Figure 7(g-Figure 7h), they also exhibit similar behaviors as in the homogeneous strains, several alien peaks appear at frequencies beyond the optical gap, the most striking difference is that the broken hexagonal symmetry results in the anisotropic optical absorbance, for the armchair compressive case, the presence of a strong exciton peak is observed for the incident light polarized along the compressive direction, while the peak with the same energy but the relatively weak intensity is observed for the incident light parallel to the zigzag direction. The opposite phenomenon is true for the expansion of the lattice constant. The polarization-dependent absorption is decided by the asymmetry of the electronic wave functions and the non-uniform of the electronic screening environments; in fact, the optical joint density of states of the first bright exciton state EXn=1E_{X}^{n=1} (the blue area in Figure 8) and the dielectric constant (ε1(0)\varepsilon_{1}(0) discusses in Table 2 and Figure 9) of the direction parallel to the compression, respectively, are larger and smaller than those of the elongation, resulting in an increased probability of the corresponding transition.

Direct V2 valence band to C1 conduction band transition energy

Figure 8. Direct V2V_{2} valence band to C1C_{1} conduction band transition energy (corresponding to EXn=1E_{X}^{n=1}) in the first Brillouin zone.

Evolution of dark and bright excitons, exciton binding energy, and static dielectric constant under strain

Figure 9. (a)–(c) The evolution of the first dark DXn=1D_{X}^{n=1} exciton and the first bright exciton EXn=1E_{X}^{n=1}, (d)–(f) the exciton binding energy ExbE_{xb} and the static dielectric constant ε1(0)\varepsilon_{1}(0) under the homogeneous, armchair, and zigzag strains.

The optical absorption spectra of GaSe under zigzag strain are presented in Figure 7(i-Figure 7j) and 7(k-l), the imaginary part of the dielectric functions exhibit substantially anisotropic behaviors; reduced electron-hole interactions result in a significant red shift of prominent absorption peaks in the tensile strains; the optical absorbance dependents on the direction of the polarization of the incident light and no longer a constant after electron-hole interactions are included. The intensity of the exciton peak for light polarized along the armchair (zigzag) is relatively lower than that of zigzag (armchair) directions under compressive (tensile) strains, respectively. This is the inverse process of the phenomenon shown in Figure 7(e-Figure 7f) and 7(g-h).

For a better insight into the excitonic effects, the evolution of the first dark exciton (DXn=1D_{X}^{n=1}), the first bright exciton (EXn=1E_{X}^{n=1}), the static dielectronic screening ε1(0)\varepsilon_{1}(0), and the exciton binding ExbE_{xb} have been calculated and thoroughly discussed in Figure 9.

The changing of the threshold frequency Figure 9a shows the different manners under compressive and tensile strains. The EXn=1E_X^{n=1} alters dramatically as a result of the band gap changing; it decreases linearly as the band gap decreases with increasing tensile strain. For compression, the evolution of EXn=1E_X^{n=1} is more complicated; for example, it increases significantly to EXn=1=4.18E_X^{n=1} = 4.18 eV at H-strain = -6% and then decreases when higher strains are applied. Figure 9a also shows the evolution of the first dark exciton state DXn=1D_X^{n=1}, there is a crossover for the dark and bright exciton types under the critical onset point H = -2%. The separation of DXn=1D_X^{n=1} and EXn=1E_X^{n=1} becomes more apparent as the strain increases towards positive values, and the dark one becomes the lowest exciton state, which agrees well with the observation that the Mexican hat-sharp dispersion becomes the top valence sub-bands and the significant energy difference between Γ\Gamma and VBM. The evolution of DXn=1D_X^{n=1} and EXn=1E_X^{n=1} under A-strain (Figure 9b) and Z-strain (Figure 9c) also followed a similar trend. However, due to differences in the levels and kinds of band gap modification, they exhibit slight differences in particular characteristics, such as the critical strain and the position of EXn=1E_X^{n=1} and DXn=1D_X^{n=1}.

Figure 9d, Figure 9e and Figure 9c sheds light on the strain-dependent of the dielectric screening ε1(0)\varepsilon_1(0), and the exciton binding energy ExbE_{\mathrm{xb}} of the GaSe monolayer. Similar to black phosphorus [72], the exciton binding energy ExbE_{\mathrm{xb}} of the GaSe monolayer sensitive changes under mechanical modifications. The exciton binding of the GaSe monolayer decreases linearly with increasing dielectric screening ε1(0)\varepsilon_1(0) or decreasing the electronic band gap and well-separation of the electron and hole states, for example, Exb=0.474E_{\mathrm{xb}} = 0.474 eV for H = +2%, Exb=0.453E_{\mathrm{xb}} = 0.453 eV for H = +6%, and Exb=0.38E_{\mathrm{xb}} = 0.38 eV for H = +10%. In contrast, ExbE_{\mathrm{xb}} exhibits a slight increase in the external compressive strain even as the electronic screening is gradually increased, e.g., Exc=0.48E_{\mathrm{xc}} = 0.48 eV and ε1(0)=3.799\varepsilon_1(0) = 3.799 at H = 0%, and Exc=0.492E_{\mathrm{xc}} = 0.492 eV and ε1(0)=3.855\varepsilon_1(0) = 3.855 for H = -6%. Such a marked difference supports the notion that the physical distance controlled by mechanical strain plays an important role in determining the exciton binding energy. These findings can be interpreted qualitatively as follows: The Coulomb interaction between the negatively charged electrons and the positively charged holes, as depicted in the simple hydrogenic model Hhydrog=−∇22m∗+e2εrH_{\mathrm{hydrog}} = -\frac{\nabla^2}{2m^*} + \frac{e^2}{\varepsilon_r}, is highly influenced by the environment’s electronic screening ε\varepsilon. The ExbE_{\mathrm{xb}}, on the other hand, is determined by the overall effects of the electronic screening as well as the physical distance between the excited hole and the excited electron rr (Schematics in Figure 10). Figure 9d indicates that the effects of the distance between two opposite-charge particles have a greater influence on their attractive couplings than that of ε1(0)\varepsilon_1(0), and as a consequence, the ExbE_{\mathrm{xb}} gradually increases with compressive strain. Not surprisingly, the impact of electron-hole physical distance no longer surpasses that of the environmental screening, and the ExbE_{\mathrm{xb}} starts to diminish at the critical strain H = -8%.

Schematic representation for the mutual couplings of the excited hole and excited electron of monolayer GaSe without and with applied strain

Figure 10. The schematic representation for the mutual couplings of the excited hole and excited electron of monolayer GaSe without (a) and with (b) compressive strain are presented.

When the electromagnetic fields incident into the surface of a medium, some of them will be reflected into the vacuum, while part of them will be transmitted, and part of them will be absorbed and transferred into the thermal reservoirs (Figure 11a). To further comprehend the effects of external mechanical perturbation on the optical properties of the GaSe monolayer, we calculated the absorbance A(ω)A(\omega), reflectance R(ω)R(\omega), and transmission T(ω)T(\omega) spectra. For the normal incidence θ=0∘\theta= 0^\circ the optical properties A(ω)A(\omega), R(ω)R(\omega), and T(ω)T(\omega) could be expressed as the following equations [73]:

Light propagation in a system consisting of a 2D sheet and frequency-dependent optical properties

Figure 11. (a) Light propagation in a system consisting of a 2D sheet. The direction of the arrows illustrates incident, reflected, and transmitted light. Frequency-dependent of the optical properties RR (blue line), T−1T-1 (green line), and AA (red line) with include excitonic effects for (b) pristine GaSe monolayer, (c) and (d) compressive and tensile homogeneous strains, (e) and (f) compressive and tensile armchair

A(ω)=Re⁡σ~∣1+σ~/2∣2A(\omega) = \frac{\operatorname{Re}\tilde{\sigma}}{\left|1+\tilde{\sigma}/2\right|^2}
R(ω)=∣σ~/21+σ~/2∣2R(\omega) = \left|\frac{\tilde{\sigma}/2}{1+\tilde{\sigma}/2}\right|^2
T(ω)=1∣1+σ~/2∣2T(\omega) = \frac{1}{\left|1+\tilde{\sigma}/2\right|^2}

where, σ~(ω)=σ2D(ω)/ε0c\tilde{\sigma}(\omega)=\sigma_{2D}(\omega)/\varepsilon_0 c is the normalized conductivity.

The GaSe monolayer only absorbs ∼2%\sim2\% to 4%4\% of the incoming light in case excluding the electron-hole interactions (See Figure S4), most of the incident light is transmitted, while a small portion of them will be reflected on the front surface. However, due to the significant excitonic effects, A(ω)A(\omega) is enhanced with more than 20% of the incoming light absorbed for the lowest bright exciton states (Figure 11b). The absorption ability of the GaSe monolayer is better than graphene (less than 5%) [73] and MoS2_2 (15%) [74]. The external mechanical perturbation exerts an important influence on the optical spectra, in addition to the changing of the absorption, reflectance, and transmission intensities, the optical spectra also expressed a significant shift into the visible and the ultraviolet spectral region, respectively, for the elongation and compression. Because the optical absorption coefficient and absorption spectral range can be easily turned by homogeneous and inhomogeneous mechanical modifications, strain engineering has emerged as an effective tool for tailoring the electronic and optical properties of two-dimensional materials for specific application demands, such as electronic, optoelectronic, and photovoltaic devices.

Because of the strong light-matter coupling, the transition energy EXn=1E_X^{n=1} of the exciton could be achieved by optical methods such as photoluminescence, reflectance, and absorbance spectroscopies. The exciton binding energy (ExbE_{xb}), on the other hand, can be evaluated by the energy difference between the exciton groundstate energy (EXn=1E_X^{n=1}) and the fundamental band gap (EgE_g), Exb=EXn=1−EgE_{xb} = E_X^{n=1} - E_g, the latter could be directly measured by scanning tunneling spectroscopy (STS) [59]. Such measurements have been established for GaSe monolayer and our theoretical predictions are in good accordance with their measurements [75].

strains, (g) and (h) compressive and tensile zigzag strains. The solid and the dash lines indicate the polarization of the fields along the armchair and zigzag directions, respectively.

Conclusions

We investigate the electronic and optical properties of deformed single-layer GaSe using first-principles calculations. The orbital interactions of Ga-4s and Se-4pz4p_z are responsible for the tailoring of V1V_1 and C1C_1 electronic states at Γ\Gamma, while the in-plane orbital interactions of Ga-(4px4p_x, 4py4p_y) and Se-(4px4p_x, 4py4p_y) related to the changing of C2C_2 state at K and V2+V3V_2 + V_3 states at Γ\Gamma. The electronic band gap and the threshold frequency exhibit considerable red shifts upon the elongation, while these variations are more complicated for compression. Because of the reduced dimensionality and weak dielectric screening, the GaSe monolayer exhibits significant excitonic effects. Our predictions also indicated that the physical distance between two opposite-charge particles controlled by mechanical strains also plays an important role in determining the exciton binding energy, ExbE_{xb} is approximately 0.48 eV for the pristine GaSe, and it decreases (increases) to 0.39 eV (0.493 eV) for the applied homogeneous tensile strain (compressive strain). The absorption coefficient is enhanced due to the presence of strong excitonic effects, the absorbance, reflection, and transmission spectra are also sensitive to external mechanical changes. Similar phenomena are observed for GaSe monolayers under inhomogeneous zigzag and armchair strains; however, due to differences in levels and types of mechanical modification, the electronic and optical spectra present differ slightly in specific characteristics, such as anisotropic energy band structure, non-uniform electronic screening environment, strong polarization of optical absorption spectra, and strain-dependent exciton binding energy. The homogeneous and inhomogeneous mechanical strains appear as a convenient way to turn the electronic and optical properties of GaSe monolayer for specific application demands, e.g., electronic, optoelectronic, and photovoltaic devices.

Competing interests

The authors declare no competing interests.

Acknowledgments

This work was financially supported by the Hierarchical Green-Energy Materials (Hi-GEM) Research Center from The Featured Areas Research Center Program within the framework of the Higher Education Sprout Project by the Ministry of Education (MOE) and the Ministry of Science and Technology (MOST 110-2634-F-006 -017) in Taiwan.

References

  1. [1]A. Gupta, T. Sakthivel, and S. Seal. Recent development in 2D materials beyond graphene. Progress in Materials Science. 2015, 73,44-126.DOI
  2. [2]G. R. Bhimanapati, Z. Lin, V. Meunier, Y. Jung, J. Cha, S. Das, et al. Recent advances in two-dimensional materials beyond graphene. ACS nano. 2015, 9,11509-11539.DOI
  3. [3]S. Das, J. A. Robinson, M. Dubey, H. Terrones, and M. Terrones. Beyond graphene: progress in novel two-dimensional materials and van der Waals solids. Annual Review of Materials Research. 2015, 45, 1-27.DOI
  4. [4]V. K. Dien, O. K. Le, V. Chihaiа, M.-P. Pham-Ho, and D. N. Son. Monolayer transition-metal dichalcogenides with polyethyleneimine adsorption. Journal of Computational Electronics. 2021, 20, 135-150.DOI
  5. [5]O. K. Le, V. Chihaiа, and M.-P. Pham-Ho. Electronic and optical properties of monolayer MoS 2 under the influence of polyethyleneimine adsorption and pressure. RSC Advances. 2020, 10, 4201-4210.DOI
  6. [6]O. K. Le, V. Chihaiа, and V. Van On. N-type and p-type molecular doping on monolayer MoS 2. RSC Advances. 2021, 11, 8033-8041.DOI
  7. [7]D. K. Nguyen, N. T. T. Tran, T. T. Nguyen, and M.-F. Lin. Diverse electronic and magnetic properties of chlorination-related graphene nanoribbons. Scientific reports. 2018, 8, 1-12.arxiv.org/abs/1801.01662
  8. [8]N. T. Tien, P. T. B. Thao, V. T. Phuc, and R. Ahuja. Electronic and transport features of sawtooth penta-graphene nanoribbons via substitutional doping. Physica E: Low-dimensional Systems and Nanostructures. 2019, 114, 113572.DOI
  9. [9]J.-H. Wong, B.-R. Wu, and M.-F. Lin. Strain effect on the electronic properties of single layer and bilayer graphene. The Journal of Physical Chemistry C. 2012, 116, 8271-8277.DOI
  10. [10]S.-Y. Lin, S.-L. Chang, F.-L. Shyu, J.-M. Lu, and M.-F. Lin. Feature-rich electronic properties in graphene ripples. Carbon. 2015, 86, 207-216.DOI
  11. [11]H.-C. Chung, C.-P. Chang, C.-Y. Lin, and M.-F. Lin. Electronic and optical properties of graphene nanoribbons in external fields. Physical Chemistry Chemical Physics. 2016, 18, 7573-7616.DOI
  12. [12]C.-Y. Lin, T.-N. Do, Y.-K. Huang, and M.-F. Lin. Optical properties of graphene in magnetic and electric fields. IOP Publishing. 2017.
  13. [13]Y.-H. Ho, Y.-H. Chiu, D.-H. Lin, C.-P. Chang, and M.-F. Lin. Magneto-optical selection rules in bilayer Bernal graphene. ACS nano. 2010, 4, 1465-1472.DOI
  14. [14]J.-Y. Wu, S.-C. Chen, O. Roslyak, G. Gumbs, and M.-F. Lin. Plasma excitations in graphene: Their spectral intensity and temperature dependence in magnetic field. ACS nano. 2011, 5, 1026-1032.DOI
  15. [15]Z. Dai, L. Liu, and Z. Zhang. Strain engineering of 2D materials: issues and opportunities at the interface. Advanced Materials. 2019, 31, 1805417.DOI
  16. [16]J. Du, H. Yu, B. Liu, M. Hong, Q. Liao, Z. Zhang, et al. Strain Engineering in 2D Material-Based Flexible Optoelectronics. Small Methods. 2021, 5, 2000919.DOI
  17. [17]S.-M. Choi, S.-H. Jhi, and Y.-W. Son. Effects of strain on electronic properties of graphene. Physical Review B. 2010, 81, 081407.DOI
  18. [18]H. Ochoa. Strain-induced excitonic instability in twisted bilayer graphene. Physical Review B. 2020, 102, 201107.DOI
  19. [19]Y. Liang, S. Huang, and L. Yang. Many-electron effects on optical absorption spectra of strained graphene. Journal of Materials Research. 2012, 27, 403-409.DOI
  20. [20]Z. Ben Aziza, H. Henck, D. Pierucci, M. G. Silly, E. Lhuillier, G. Patriarche, et al. van der Waals epitaxy of GaSe/graphene heterostructure: electronic and interfacial properties. ACS nano. 2016, 10, 9679-9686.DOI
  21. [21]Z. Zhu, Y. Cheng, and U. Schwingenschlögl. Topological phase transition in layered GaS and GaSe. Physical review letters. 2012, 108, 266805.pubmed.ncbi.nlm.nih.gov/23005005
  22. [22]H. Nitta, T. Yonezawa, A. Fleurence, Y. Yamada-Takamura, and T. Ozaki. First-principles study on the stability and electronic structure of monolayer GaSe with trigonal-antiprismatic structure. Physical Review B. 2020, 102, 235407.DOI
  23. [23]X. Zhou, J. Cheng, Y. Zhou, T. Cao, H. Hong, Z. Liao, et al. Strong Second-Harmonic Generation in Atomic Layered GaSe. Journal of the American Chemical Society. 2015, 137, 7994-7997.DOI
  24. [24]L. Karvonen, A. Säynätjoki, S. Mehravar, R. D. Rodriguez, S. Hartmann, D. R. T. Zahn, et al. Investigation of Second- and Third-Harmonic Generation in Few-Layer Gallium Selenide by Multiphoton Microscopy. Scientific Reports. 2015, 5, 10334.DOI
  25. [25]P. Hu, L. Wang, M. Yoon, J. Zhang, W. Feng, X. Wang, et al. Highly Responsive Ultrathin GaS Nanosheet Photodetectors on Rigid and Flexible Substrates. Nano Letters. 2013, 13, 1649-1654.DOI
  26. [26]Y. Lu, J. Chen, T. Chen, Y. Shu, R.-J. Chang, Y. Sheng, et al. Controlling Defects in Continuous 2D GaS Films for High-Performance Wavelength-Tunable UV-Discriminating Photodetectors. Advanced Materials. 2020, 32, 1906958.DOI
  27. [27]P. Hu, Z. Wen, L. Wang, P. Tan, and K. Xiao. Synthesis of Few-Layer GaSe Nanosheets for High Performance Photodetectors. ACS Nano. 2012, 6, 5988-5994.DOI
  28. [28]X. Li, M.-W. Lin, J. Lin, B. Huang, A. A. Puretzky, C. Ma, et al. Two-dimensional GaSe/MoSe<sub>2</sub> misfit bilayer heterojunctions by van der Waals epitaxy. Science Advances. 2016, 2, e1501882.DOI
  29. [29]Z. Chen, S. Chu, C. Chen, H. Chen, J. Zhang, X. Ma, et al. Epitaxially grown semi-vertical and aligned GaTe two dimensional sheets on ZnO substrate for energy harvesting applications. Nano Energy. 2019, 56, 294-299.DOI
  30. [30]H. L. Zhuang and R. G. Hennig. Single-Layer Group-III Monochalcogenide Photocatalysts for Water Splitting. Chemistry of Materials. 2013, 25, 3232-3238.DOI
  31. [31]Y. Fan, X. Ma, X. Liu, J. Wang, H. Ai, and M. Zhao. Theoretical Design of an InSe/GaTe vdW Heterobilayer: A Potential Visible-Light Photocatalyst for Water Splitting. The Journal of Physical Chemistry C. 2018, 122, 27803-27810.DOI
  32. [32]O. I. Aksimentyeva, P. Y. Demchenko, V. P. Savchyn, and O. A. Balitskii. The chemical exfoliation phenomena in layered GaSe-polyaniline composite. Nanoscale Research Letters. 2013, 8, 29.DOI
  33. [33]M. Usman, S. Golovynskyi, D. Dong, Y. Lin, Z. Yue, M. Imran, et al. Raman Scattering and Exciton Photoluminescence in Few-Layer GaSe: Thickness- and Temperature-Dependent Behaviors. The Journal of Physical Chemistry C. 2022, 126, 10459-10468.DOI
  34. [34]X. Li, L. Basile, B. Huang, C. Ma, J. Lee, I. V. Vlassiouk, et al. Van der Waals epitaxial growth of two-dimensional single-crystalline GaSe domains on graphene. ACS nano. 2015, 9, 8078-8088.DOI
  35. [35]N. Zhou, R. Wang, X. Zhou, H. Song, X. Xiong, Y. Ding, et al. P-GaSe/N-MoS2 vertical heterostructures synthesized by van der Waals epitaxy for photoresponse modulation. Small. 2018, 14, 1702731.DOI
  36. [36]Z. He, J. Guo, S. Li, Z. Lei, L. Lin, Y. Ke, et al. GaSe/MoS2 Heterostructure with Ohmic-Contact Electrodes for Fast, Broadband Photoresponse, and Self-Driven Photodetectors. Advanced Materials Interfaces. 2020, 7, 1901848.DOI
  37. [37]Y. Ma, Y. Dai, M. Guo, L. Yu, and B. Huang. Tunable electronic and dielectric behavior of GaS and GaSe monolayers. Physical Chemistry Chemical Physics. 2013, 15, 7098-7105.DOI
  38. [38]M. Rahaman, M. Bejani, G. Salvan, S. A. Lopez-Rivera, O. Pulci, F. Bechstedt, et al. Vibrational properties of GaSe: a layer dependent study from experiments to theory. Semiconductor Science and Technology. 2018, 33, 125008.DOI
  39. [39]A. Kumar and P. K. Ahluwalia. Electronic structure of transition metal dichalcogenides monolayers 1H-MX2 (M = Mo, W; X = S, Se, Te) from ab-initio theory: new direct band gap semiconductors. The European Physical Journal B. 2012, 85, 186.DOI
  40. [40]H. Huang, P. Wang, Y. Gao, X. Wang, T. Lin, J. Wang, et al. Highly sensitive phototransistor based on GaSe nanosheets. Applied Physics Letters. 2015, 107, 143112.DOI
  41. [41]G. Antonius, D. Y. Qiu, and S. G. Louie. Orbital Symmetry and the Optical Response of Single-Layer MX Monochalcogenides. Nano Letters. 2018, 18, 1925-1929.DOI
  42. [42]M. Yagm urcukardes, R. T. Senger, F. M. Peeters, and H. Sahin. Mechanical properties of monolayer GaS and GaSe crystals. Physical Review B. 2016, 94,245407.
  43. [43]E. Engel and R. M. Dreizler. Density functional theory. Springer. 2013.
  44. [44]D. Wing, J. B. Haber, R. Noff, B. Barker, D. A. Egger, A. Ramasubramaniam, et al. Comparing time-dependent density functional theory with many-body perturbation theory for semiconductors: Screened range-separated hybrids and the G W plus Bethe-Salpeter approach. Physical Review Materials. 2019, 3,064603.
  45. [45]J. Hafner. Ab-initio simulations of materials using VASP: Density-functional theory and beyond. Journal of Computational Chemistry. 2008, 29,2044-2078.DOI
  46. [46]J. P. Perdew, K. Burke, and M. Ernzerhof. Generalized Gradient Approximation Made Simple. Physical Review Letters. 1996, 77,3865-3868.pubmed.ncbi.nlm.nih.gov/10062328
  47. [47]G. Kresse and D. Joubert. From ultrasoft pseudopotentials to the projector augmented-wave method. Physical Review B. 1999, 59,1758-1775.DOI
  48. [48]P. Wisesa, K. A. McGill, and T. Mueller. Efficient generation of generalized Monkhorst-Pack grids through the use of informatics. Physical Review B. 2016, 93,155109.DOI
  49. [49]M. S. Hybertsen and S. G. Louie. Electron correlation in semiconductors and insulators: Band gaps and quasiparticle energies. Physical Review B. 1986, 34,5390.pubmed.ncbi.nlm.nih.gov/9940372
  50. [50]M. Rohlfing and S. G. Louie. Electron-hole excitations and optical spectra from first principles. Physical Review B. 2000, 62,4927-4944.DOI
  51. [51]Z. B. Aziza, V. Zólyomi, H. Henck, D. Pierucci, M. G. Silly, J. Avila, et al. Valence band inversion and spin-orbit effects in the electronic structure of monolayer GaSe. Physical Review B. 2018, 98,115405.
  52. [52]L. Huang, Z. Chen, and J. Li. Effects of strain on the band gap and effective mass in two-dimensional monolayer GaX (X = S, Se, Te). RSC Advances. 2015, 5,5788-5794.DOI
  53. [53]T. Cao, Z. Li, and S. G. Louie. Tunable Magnetism and Half-Metallicity in Hole-Doped Monolayer GaSe. Physical Review Letters. 2015, 114,236602.pubmed.ncbi.nlm.nih.gov/26196815
  54. [54]D. V. Rybkovsky, N. R. Arutyunyan, A. S. Orekhov, I. A. Gromchenko, I. V. Vorobiev, A. V. Osadchy, et al. Size-induced effects in gallium selenide electronic structure: The influence of interlayer interactions. Physical Review B. 2011, 84,085314.
  55. [55]Z. B. Aziza, D. Pierucci, H. Henck, M. G. Silly, C. David, M. Yoon, et al. Tunable quasiparticle band gap in few-layer GaSe/graphene van der Waals heterostructures. Physical Review B. 2017, 96,035407.
  56. [56]M. Wu, J.-j. Shi, M. Zhang, Y.-m. Ding, H. Wang, Y.-l. Cen, et al. Enhancement of photoluminescence and hole mobility in 1- to 5-layer InSe due to the top valence-band inversion: strain effect. Nanoscale. 2018, 10,11441-11451.DOI
  57. [57]B. Lv, T. Qian, and H. Ding. Angle-resolved photoemission spectroscopy and its application to topological materials. Nature Reviews Physics. 2019, 1,609-626.
  58. [58]W. Wei, Y. Dai, C. Niu, X. Li, Y. Ma, and B. Huang. Electronic properties of two-dimensional van der Waals GaS/GaSe heterostructures. Journal of Materials Chemistry C. 2015, 3,11548-11554.DOI
  59. [59]Z. Ben Aziza, D. Pierucci, H. Henck, M. G. Silly, C. David, M. Yoon, et al. Tunable quasiparticle band gap in few-layer GaSe/graphene van der Waals heterostructures. Physical Review B. 2017, 96,035407.DOI
  60. [60]M. Ghorbani-Asl, S. Borini, A. Kuc, and T. Heine. Strain-dependent modulation of conductivity in single-layer transition-metal dichalcogenides. Physical Review B. 2013, 87,235434.
  61. [61]P. Johari and V. B. Shenoy. Tuning the Electronic Properties of Semiconducting Transition Metal Dichalcogenides by Applying Mechanical Strains. ACS Nano. 2012, 6,5449-5456.DOI
  62. [62]N. Thi Han, V. Khuong Dien, and M.-F. Lin. Electronic and Optical Properties of CsGeX3 (X= Cl, Br, and I) Compounds. ACS Omega. 2022, 7,25210-25218.DOI
  63. [63]V. K. Dien, N. T. Han, W.-P. Su, and M.-F. Lin. Spin-dependent Optical Excitations in LiFeO2. ACS Omega. 2021, 6,25664-25671.DOI
  64. [64]V. K. Dien, H. D. Pham, N. T. T. Tran, N. T. Han, T. M. D. Huynh, T. D. H. Nguyen, et al. Orbital-hybridization-created optical excitations in Li2GeO3. Scientific Reports. 2021, 11,4939.DOI
  65. [65]N. T. Han, V. K. Dien, and M.-F. Lin. Excitonic effects in the optical spectra of Li2SiO3 compound. Scientific Reports. 2021, 11,7683.DOI
  66. [66]V. Khuong Dien, W.-B. Li, K.-I. Lin, N. Thi Han, and M.-F. Lin. Electronic and optical properties of graphene, silicene, germanene, and their semi-hydrogenated systems. RSC Advances. 2022, 12,34851-34865.DOI
  67. [67]Y. Lin, X. Ling, L. Yu, S. Huang, A. L. Hsu, Y.-H. Lee, et al. Dielectric screening of excitons and trions in single-layer MoS2. Nano letters. 2014, 14,5569-5576.DOI
  68. [68]D. Y. Qiu, H. Felipe, and S. G. Louie. Optical spectrum of MoS 2: many-body effects and diversity of exciton states. Physical review letters. 2013, 111,216805.DOI
  69. [69]D. Y. Qiu, F. H. da Jornada, and S. G. Louie. Screening and many-body effects in two-dimensional crystals: Monolayer ${\mathrm{MoS}}_{2}$. Physical Review B. 2016, 93,235435.DOI
  70. [70]D. Y. Qiu, F. H. da Jornada, and S. G. Louie. Environmental Screening Effects in 2D Materials: Renormalization of the Bandgap, Electronic Structure, and Optical Spectra of Few-Layer Black Phosphorus. Nano Letters. 2017, 17,4706-4712.DOI
  71. [71]T. Mueller and E. Malic. Exciton physics and device application of two-dimensional transition metal dichalcogenide semiconductors. npj 2D Materials and Applications. 2018, 2,29.DOI
  72. [72]D. Çakır, H. Sahin, and F. M. Peeters. Tuning of the electronic and optical properties of single-layer black phosphorus by strain. Physical Review B. 2014, 90,205421.DOI
  73. [73]L. Matthes, O. Pulci, and F. Bechstedt. Influence of out-of-plane response on optical properties of two-dimensional materials: First principles approach. Physical Review B. 2016, 94,205408.DOI
  74. [74]Y. Li, A. Chernikov, X. Zhang, A. Rigosi, H. M. Hill, A. M. van der Zande, et al. Measurement of the optical dielectric function of monolayer transition-metal dichalcogenides: ${\mathrm{MoS}}_{2}$, ${\mathrm{MoSe}}_{2}$, ${\mathrm{WS}}_{2}$, and ${\mathrm{WSe}}_{2}$. Physical Review B. 2014, 90,205422.
  75. [75]C. S. Jung, F. Shojaei, K. Park, J. Y. Oh, H. S. Im, D. M. Jang, et al. Red-to-Ultraviolet Emission Tuning of Two-Dimensional Gallium Sulfide/Selenide. ACS Nano. 2015, 9,9585-9593.DOI

Paper details

vlnc:W_m4yp5a7s
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents