betaFeedback

WorksPhysics and Astronomy

Analytical Modeling of the Admittance Tensor of Periodic Elliptical Meta-Atoms

Abstract

A metasurface is an electrically thin interface that controls the phase, amplitude and polarization of a wave, upon reflection or transmission. Printed on a grounded dielectric substrate and spatially modulated across the aperture, it converts a guided surface wave into a radiated leaky wave, a mechanism used in holographic metasurface antennas. Controlling this conversion requires synthesizing a prescribed distribution of admittance tensors, each derived from the homogenization of a subwavelength unit cell. Many numerical and semi-analytical methods have been proposed to relate the geometry of a meta-atom to the tensor it produces. This paper presents, to the author's knowledge, the first analytical model, restricted to elliptical meta-atoms on a uniform lattice. The Galerkin method is applied directly to the geometry of the patches, without spatial meshing. An affine transformation maps any rotated ellipse onto the unit disk, so that a single formulation covers every configuration. A wideband response takes from minutes to tens of minutes with a periodic full-wave solver, while the proposed model evaluates it in a few tens of milliseconds on the same workstation, roughly three orders of magnitude faster. The predicted admittance agrees with a method-of-moments reference up to the fundamental resonance and captures the guided-mode anomaly of the substrate. Beyond the physical insight it brings, the model is a differentiable function of the geometry, which makes the quasi-real-time design of optimized metasurfaces possible.

Introduction

Periodic arrays of metallic patches on grounded dielectric substrates are widely used to design metasurfaces and holographic screens [1, 2, 3, 4]. In the subwavelength regime, the array is characterized by an effective sheet admittance tensor Ys\mathbf{Y}_{s} relating the average tangential electric field to the induced surface current, Js=Ys⋅Et\mathbf{J}_{s}=\mathbf{Y}_{s}\cdot\mathbf{E}_{t} [5]. In the low-frequency limit, the admittance of isolated metal elements is purely capacitive, Ys(ω)=jωC\mathbf{Y}_{s}(\omega)=j\omega\mathbf{C}, where the symmetric positive-definite tensor C∈R2×2\mathbf{C}\in\mathbb{R}^{2\times2} accounts for patch dimensions, orientation, lattice periods, and substrate loading.

Anisotropic cells are of particular interest in this context. An elliptical patch with semi-axes Ae≠BeA_{e}\ne B_{e}, rotated by an angle ψ\psi, allows independent control of the principal admittance eigenvalues and their orientation. In contrast to slotted patches or double π\pi structures, the elliptical contour avoids sharp reentrant corners and offers smooth geometric tuning [3, 6]. Synthesizing such metasurfaces requires determining the local geometry that achieves a prescribed admittance profile across the aperture. Solving this inverse problem can involve thousands of evaluations of the forward model, which scales the optimization time of a metasurface from seconds to hours.

Determining the forward electromagnetic response involves balancing accuracy and computational cost. Analytical grid-impedance models proposed by Luukkonen et al. [8] yield closed-form expressions for planar strips or rectangular patches using averaged boundary conditions, but do not apply to curved boundaries. Multimodal equivalent-circuit models [9, 10] extend this description to the dynamic regime by retaining a few Floquet harmonics, with a current profile on the scatterer that is fixed a priori or extracted from a single full-wave simulation. Pole-zero matching models [11] describe the frequency dependence of the sheet admittance, following Foster’s reactance theorem. At the other end of this range, full-wave numerical solvers handle arbitrary geometries, but their computational burden remains prohibitive for iterative design sweeps.

For elliptical geometries, Mencagli et al. [6] proposed a reduced spectral Method of Moments with three analytical basis functions obtained by stretching circular-patch models. It describes the anisotropic surface-wave dispersion in the homogenization regime, well below the patch resonance, but it still requires the solution of a spectral MoM system over the Floquet lattice. In a subsequent work [7], the same authors proposed a two-stage semi-analytical model in which a Cardano transition function relates the dynamic surface reactance to the inductance of the grounded slab and to a single parameter per eigenaxis, the quasi-static patch capacitance C0C_{0}, which allows a fast evaluation of the dispersion curve. This approach has two limitations. First, there is no analytical formulation of C0C_{0} for elliptical patches, which has to be extracted from full-wave simulations or from an extension of Luukkonen’s planar-grid formula with an area-equivalent rectangular gap [8]. Second, the single-mode approximation loses accuracy for elongated patches and departs from full-wave results well before the patch resonance.

In this context, this paper proposes an analytical spectral framework that bypasses full-wave simulations for periodic elliptical meta-atoms while maintaining wideband accuracy (Figure 1). Rather than a spatial mesh of the patch, the Galerkin method is formulated directly on the geometry. Following the disk-to-ellipse stretching similarly used in [6, 12], the family of rotated ellipses is projected onto a canonical unit disk, where a tailored Jacobi basis is defined. In the first stage, the quasi-static capacitance tensor C\mathbf{C} is extracted on this disk by expanding the surface charge on Jacobi polynomials that incorporate the Meixner edge singularity [13]. With Fourier transforms available in closed form, C\mathbf{C} is evaluated without

Figure 1. Two-stage analytical procedure for elliptical meta-atoms. Stage 1 (electrostatics): the Jacobi–Galerkin solver gives the quasi-static capacitance tensor C\mathbf{C} from the geometry, instead of a full-wave extraction or an equivalent-gap extension of planar grid models. Stage 2 (electrodynamics): the spectra of the charge-carrying and solenoidal surface currents define an effective magnetic interaction matrix, and the dynamic Galerkin system gives the dispersive sheet admittance tensor Ys(ω)\mathbf{Y}_{s}(\omega), to be compared with the single-mode Cardano model of Mencagli et al. [7].

T. Fromentèze is with the University of Limoges, CNRS, XLIM, UMR 7252, F-87000 Limoges, France, and also with the Institut universitaire de France (IUF) (e-mail: [email protected]).

This work was supported by the Institut universitaire de France (IUF) and the CNRS MITI “Interactions Complexes” program. spatial meshing. The periodic coupling is decomposed into an isolated-patch term and a multipole series over neighboring cells, which eliminates Floquet truncations in electrostatics and extends methods known for circular disks [14, 15, 16]. In the second stage, this solver is coupled to a mixed-potential integral equation [17], with surface currents transported from the disk via affine mapping [18]. This yields the dispersive admittance tensor up to the patch resonance and accounts for substrate guided modes. Because every step is expressed in closed form from the geometric parameters, the entire pipeline is a smooth function of (Ae,Be,ψ)(A_e, B_e, \psi) away from the guided-mode poles, which makes it possible to compute gradients with respect to the geometry for gradient-based metasurface synthesis [19], [20]. A Python implementation is available as supplementary material to facilitate the reproduction of this work [21].

where kmn=(2πm/dx,2πn/dy)\mathbf{k}_{mn} = (2\pi m/d_x, 2\pi n/d_y) is the Floquet harmonic, σ^(kmn)\hat{\sigma}(\mathbf{k}_{mn}) is the Floquet coefficient of the charge, and E0\mathbf{E}_0 is the applied uniform electric field. The k00\mathbf{k}_{00} term drops out because each patch is electrically neutral (σ^(0)=0)(\hat{\sigma}(\mathbf{0}) = 0). Here, E0\mathbf{E}_0 denotes the macroscopic tangential field at the sheet [5, 22]. Since all retained basis functions have an odd angular order (Section III-D), the constant potential V0V_0 is orthogonal to the basis and drops out of the Galerkin system. The substrate and ground plane enter through the quasi-static spectral Green’s

Problem Formulation

Consider a periodic array (periods dxd_x, dyd_y) of elliptical patches (semi-axes AeA_e, BeB_e, in-plane rotation ψ\psi) printed on a dielectric substrate (εr\varepsilon_r, thickness hh) backed by a ground plane, as depicted in Figure 2. The metallization is modeled as a perfect electric conductor (PEC) of negligible thickness, and the dielectric substrate is assumed lossless (tan⁡δ=0\tan\delta= 0, εr∈R\varepsilon_r \in\mathbb{R}). For a square lattice (dx=dy=dd_x = d_y = d) aligned with the patch principal axes (ψ=0∘\psi= 0^\circ), the edge-to-edge gap between adjacent patches is g=d−2Aeg = d - 2A_e along the major axis (and gy=d−2Beg_y = d - 2B_e along the minor axis). In the quasi-static limit (ω→0\omega\to0), the sheet admittance tensor reduces to

Figure 2. Problem geometry. (a) Top view: periodic lattice (periods dxd_x, dyd_y) of elliptical PEC patches with semi-axes AeA_e, BeB_e and in-plane rotation ψ\psi. (b) Cross-section: patches at the air–substrate interface z=0z = 0, single-layer substrate (εr(\varepsilon_r, thickness h)h), PEC ground plane at z=−hz = -h.

Ys(ω)=jωC,C∈R2×2.(1)\mathbf{Y}_s(\omega) = j\omega\mathbf{C}, \qquad\mathbf{C} \in\mathbb{R}^{2 \times2}. \tag*{(1)}

Throughout the paper, j=−1j = \sqrt{-1} under the ejωte^{j\omega t} convention, jνj_\nu is the spherical Bessel function of order ν\nu and JνJ_\nu the cylindrical one. Determining C\mathbf{C} requires solving an electrostatic integral equation for the unknown surface charge density σ(r)\sigma(\mathbf{r}). Periodic over the unit cell of area S=dxdyS = d_xd_y, σ(r)\sigma(\mathbf{r}) satisfies on the patch

1S∑kmn≠0G~(∣kmn∣)σ^(kmn)ejkmn⋅r=V0+E0⋅r.(2)\frac{1}{S}\sum_{\mathbf{k}_{mn}\ne\mathbf{0}}\widetilde{G}(\lvert\mathbf{k}_{mn}\rvert)\hat{\sigma}(\mathbf{k}_{mn})e^{j\mathbf{k}_{mn}\cdot\mathbf{r}} = V_0 + \mathbf{E}_0\cdot\mathbf{r}. \tag*{(2)}

kernel of Mosig [23] (Appendix A):

G~(k)=1ε0k(1+εrcoth⁡(kh))(3)\widetilde{G}(k)=\frac{1}{\varepsilon_0 k\left(1+\varepsilon_r\coth(kh)\right)} \tag*{(3)}

For kh≫1kh\gg1, coth⁡(kh)→1\coth(kh)\to1 (semi-infinite substrate), whereas for kh≪1kh\ll1, G~→h/(ε0εr)\widetilde{G}\to h/(\varepsilon_0\varepsilon_r) (parallel-plate limit). The formulation can be extended to multilayer substrates with transmission-line theory, and to skewed lattices by changing the reciprocal basis that generates the harmonics kmnk_{mn}.

Spectral Galerkin Solver

The Galerkin method expands the unknown charge as σ(r)=∑nqnΦn(r)\sigma(\mathbf{r})=\sum_n q_n\Phi_n(\mathbf{r}) and tests the residual with the same functions. On a periodic lattice, this testing is carried out in the Fourier domain through Parseval’s identity (Section III-D). Rather than a spatial mesh of the metallic patch, the Galerkin scheme is formulated directly on the geometry: an affine coordinate transformation projects the continuous elliptical domain onto a canonical unit disk, where an edge-adapted spectral basis is defined analytically (Figure 3).

Figure 3. Four-stage analytical spectral Galerkin formulation: (1) Coordinate mapping of the tilted elliptical patch to the unit disk. (2) Separable basis factorized into angular harmonics cos⁡mθ\cos m\theta and radial Jacobi polynomials Rm,q(ρ)R_{m,q}(\rho) incorporating the (1−ρ2)−1/2(1-\rho^2)^{-1/2} Meixner edge condition. (3) Closed-form 2-D spatial modes Φm,q\Phi_{m,q} and their analytical Fourier spectra σ^m,q(k)∝jm+2q(κ)cos⁡mθκ\hat{\sigma}_{m,q}(\mathbf{k}) \propto j^{m+2q}(\kappa)\cos m\theta_{\kappa}. (4) Lattice decomposition into the isolated-patch term (R=0\mathbf{R}=0) and a multipole series over the neighboring cells (R≠0\mathbf{R}\ne0).

Coordinate Mapping to the Unit Disk

The physical ellipse is mapped to the unit disk via the coordinate transformation r=RψDρ\mathbf{r}=\mathbf{R}_{\psi}\mathbf{D}\boldsymbol{\rho}:

D=diag⁡(Ae,Be),Rψ=(cos⁡ψ−sin⁡ψsin⁡ψcos⁡ψ)(4)\mathbf{D}=\operatorname{diag}(A_e,B_e),\qquad \mathbf{R}_{\psi}= \begin{pmatrix} \cos\psi& -\sin\psi\\ \sin\psi& \cos\psi \end{pmatrix} \tag*{(4)}

Points ρ=(ρcos⁡θ,ρsin⁡θ)\boldsymbol{\rho}=(\rho\cos\theta,\rho\sin\theta) on the unit disk (ρ≤1\rho\le1) map to points r=(x,y)\mathbf{r}=(x,y) on an ellipse of semi-axes AeA_e and BeB_e rotated by an angle ψ\psi. The Jacobian of the transformation is constant and equals the area factor AeBeA_eB_e.

Jacobi Basis and Edge Condition

When an isolated conducting patch is placed in an external electric field, mutual repulsion drives the free charges toward the perimeter, where the surface charge density diverges as (1−ρ2)−1/2(1-\rho^2)^{-1/2} on the mapped unit disk (Meixner edge condition [13]). An expansion basis for the charge therefore has to meet three criteria: carry this edge divergence, be regular at the patch center, where a mode of angular order mm behaves as ρm\rho^m, and resolve the smooth interior distortions caused by the neighboring cells. A basis of smooth polynomials meets the last two constraints, but not the first one: reconstructing the edge accumulation from smooth functions requires many terms and converges slowly [24, 25]. The singularity is thus built into the basis itself, and only the smooth remainder has to be expanded:

Φm,qc/s(ρ,θ)=ρm(1−ρ2)−1/2Pq(−1/2,m)(2ρ2−1)Nm,q{cos⁡mθsin⁡mθ(5)\Phi_{m,q}^{c/s}(\rho,\theta)=\frac{\rho^m(1-\rho^2)^{-1/2}P_q^{(-1/2,m)}(2\rho^2-1)}{N_{m,q}} \begin{cases} \cos m\theta\\ \sin m\theta \end{cases} \tag*{(5)}

where m∈{1,3,5,…,mmax⁡}m\in\{1,3,5,\ldots,m_{\max}\} denotes the odd angular orders, q∈{0,…,qmax⁡}q\in\{0,\ldots,q_{\max}\} the radial indices, Nm,qN_{m,q} the modal normalization known in closed form [26] (Appendix B), and Rm,q(ρ)=ρm(1−ρ2)−1/2Pq(−1/2,m)(2ρ2−1)/Nm,qR_{m,q}(\rho)=\rho^m(1-\rho^2)^{-1/2}P_q^{(-1/2,m)}(2\rho^2-1)/N_{m,q}, the radial profile of the mode. The Jacobi polynomials Pq(−1/2,m)P_q^{(-1/2,m)} are orthogonal under the edge weight itself, and the radial index qq thus only describes the smooth interior of the charge.

For the fundamental dipole mode (m=1,q=0)(m=1,q=0), the basis function reproduces the exact electrostatic charge distribution of an isolated conducting ellipse under a uniform field [27]. The expansion thus starts from the dominant response of an isolated patch, and the higher orders (m≥3,q≥1)(m\ge3,q\ge1) only describe the coupling between elements, which gives fast convergence. This justifies a small basis: the six functions (m,q)∈{(1,0),(1,1),(3,0)}(m,q)\in\{(1,0),(1,1),(3,0)\} of both the cosine and the sine families, Nb=6N_b=6, are used in the rest of the paper. The adequacy of this truncation is quantified in § 5-C, where the capacitance solver is compared with a converged reference of 50 functions (mmax⁡=9m_{\max}=9, qmax⁡=4q_{\max}=4).

Closed-Form Fourier Spectra

The Galerkin matrix elements require the two-dimensional Fourier transform of the charge basis functions over the patch:

σ^(k)=∬patchσ(r)e−jk⋅r d2r.(6)\hat{\sigma}(\mathbf{k})=\iint_{\mathrm{patch}}\sigma(\mathbf{r})e^{-j\mathbf{k}\cdot\mathbf{r}}\,d^2r. \tag*{(6)}

Applying the coordinate mapping r=RψDρ\mathbf{r}=\mathbf{R}_{\psi}\mathbf{D}\boldsymbol{\rho} scales the surface element by the Jacobian AeBeA_eB_e. With the kernel plane wave expanded into cylindrical harmonics (the Jacobi–Anger expansion [28], detailed in Appendix B), the angular integration isolates the angular order mm of the mode and leaves a one-dimensional radial transform:

σ^m,qc(k)=2πAeBe(−j)mF^m,q(κ)cos⁡(mθκ),(7)\hat{\sigma}_{m,q}^{c}(\mathbf{k})=2\pi A_eB_e(-j)^m\hat{F}_{m,q}(\kappa)\cos(m\theta_{\kappa}), \tag*{(7)}

where κ=DRψTk=κ(cos⁡θκ,sin⁡θκ)\boldsymbol{\kappa}=\mathbf{D}\mathbf{R}_{\psi}^{T}\mathbf{k}=\kappa(\cos\theta_{\kappa},\sin\theta_{\kappa}) is the Floquet wavevector in the disk frame, with sin⁡(mθκ)\sin(m\theta_{\kappa}) replacing cos⁡(mθκ)\cos(m\theta_{\kappa}) for the sine family Φm,qs\Phi_{m,q}^{s}.

The radial spectrum evaluates in closed form at every radial order qq:

F^m,q(κ)=(−1)q(2qq)4−qjm+2q(κ)Nm,q,(8)\hat{F}_{m,q}(\kappa)=(-1)^q\binom{2q}{q}4^{-q}\frac{j_{m+2q}(\kappa)}{N_{m,q}}, \tag*{(8)}

where jm+2qj_{m+2q} is the spherical Bessel function of order m+2qm+2q. Physically, the sharp (1−ρ2)−1/2(1-\rho^2)^{-1/2} edge accumulation governs the high-wavenumber decay of the patch spectrum, which maps the Jacobi basis directly onto spherical Bessel functions in the Fourier domain [14], [29] (Appendix B). Both the spectra and the modal norms are obtained in closed form, and no numerical integration over the patch is needed. The remaining lattice sum of the Galerkin matrix is treated in Section III-E.

Capacitance Tensor Evaluation

Projecting the electrostatic boundary condition (2) onto the Jacobi basis functions gives the linear system

Mq=dphys,(9)\mathbf{M}\mathbf{q}=\mathbf{d}_{\mathrm{phys}}, \tag*{(9)}

whose matrix elements are evaluated in reciprocal space by Parseval’s identity,

Mab=1S∑kmn≠0G~(∣kmn∣)[σ^a(kmn)]∗σ^b(kmn).(10)M_{ab}=\frac{1}{S}\sum_{\mathbf{k}_{mn}\ne0}\widetilde{G}(\lvert\mathbf{k}_{mn}\rvert)\left[\hat{\sigma}_a(\mathbf{k}_{mn})\right]^*\hat{\sigma}_b(\mathbf{k}_{mn}). \tag*{(10)}

Since G~(k)>0\widetilde{G}(k)>0, the matrix M\mathbf{M} is symmetric positive-definite. The excitation vector dphys∈RNb×2\mathbf{d}_{\mathrm{phys}}\in\mathbb{R}^{N_b\times2} collects the projections of the uniform fields E0=x^\mathbf{E}_0=\hat{\mathbf{x}} and E0=y^\mathbf{E}_0=\hat{\mathbf{y}} onto the basis:

di,b=∬patchriΦb(r) d2r.(11)d_{i,b}=\iint_{\mathrm{patch}}r_i\Phi_b(\mathbf{r})\,d^2r. \tag*{(11)}

A uniform field along a principal axis only shifts the charge toward one side of the patch, which is the pattern of the dipole mode. In the ellipse-aligned frame r′=RψTr=(Aeρcos⁡θ,Beρsin⁡θ)\mathbf{r}'=\mathbf{R}_{\psi}^{T}\mathbf{r}=(A_e\rho\cos\theta,B_e\rho\sin\theta), the angular integral in (11) selects the order m=1m=1, and the orthogonality of the Jacobi polynomials cancels all radial orders q≥1q\ge1. For each polarization, dphys\mathbf{d}_{\mathrm{phys}} has therefore a single non-zero entry, the dipole mode (m,q)=(1,0)(m,q)=(1,0) of the cosine or of the sine family, equal to 2πAe2Be/62\pi A_e^2B_e/\sqrt{6} and 2πAeBe2/62\pi A_eB_e^2/\sqrt{6} respectively (Appendix B), and rotated by ψ\psi in the lattice frame. The other modes are excited only through the coupling with the neighboring cells in M\mathbf{M}. The lattice is centrosymmetric, and the spectrum of a mode of order mm changes by the factor (−1)m(-1)^m under k→−k\mathbf{k}\rightarrow-\mathbf{k}, so that the terms of (10) cancel when ma+mbm_a+m_b is odd. Even and odd orders are thus not coupled, and the even orders are left out of the basis for any lattice and any rotation ψ\psi.

Under an applied field E0\mathbf{E}_0, the induced dipole moment is p=dphysTq\mathbf{p}=\mathbf{d}_{\mathrm{phys}}^{T}\mathbf{q}. The macroscopic surface capacitance tensor C∈R2×2\mathbf{C}\in\mathbb{R}^{2\times2}, relating the average surface polarization density P=p/S\mathbf{P}=\mathbf{p}/S to E0\mathbf{E}_0, follows directly:

C=1SdphysTM−1dphys.(12)\mathbf{C}=\frac{1}{S}\mathbf{d}_{\mathrm{phys}}^{T}\mathbf{M}^{-1}\mathbf{d}_{\mathrm{phys}}. \tag*{(12)}

Lattice Sum Without Floquet Truncation

Evaluating the Galerkin matrix directly in the spectral domain via (10) converges slowly. The kernel (3) decays as 1/k1/k, and each spectrum (8), proportional to a spherical Bessel function, as 1/k1/k. The summands of (10), products of the kernel and of two spectra, therefore fall off as ∣kmn∣−3\lvert\mathbf{k}_{mn}\rvert^{-3} on average, and cutting off the sum at ∣kmn∣≤Λ\lvert\mathbf{k}_{mn}\rvert\le\Lambda leaves a truncation error of order 1/Λ1/\Lambda. Physically, this slow spectral convergence reflects the sharp localized nature of the near-field interaction around each patch. It is therefore of interest to reformulate the interaction in real space, where the ground plane screens the fields of distant cells. Because all retained basis functions have an odd angular order, σ^a(0)=0\hat{\sigma}_a(0)=0, and the harmonic k00\mathbf{k}_{00} can be added to (10) without altering the sum. Applying the Poisson summation formula then transforms the reciprocal-space series into a sum of pair interactions Wab(R)W_{ab}(\mathbf{R}) over the direct lattice translations R\mathbf{R}:

Mab=∑RWab(R),M_{ab}=\sum_{\mathbf{R}}W_{ab}(\mathbf{R}),
Wab(R)=∫d2k(2π)2G~(∣k∣)[σ^a(k)]∗σ^b(k)ejk⋅R.(13)W_{ab}(\mathbf{R})=\int\frac{d^2k}{(2\pi)^2}\widetilde{G}(\lvert\mathbf{k}\rvert)\left[\hat{\sigma}_a(\mathbf{k})\right]^*\hat{\sigma}_b(\mathbf{k})e^{j\mathbf{k}\cdot\mathbf{R}}. \tag*{(13)}

This decomposition separates the problem into the self-interaction of an isolated patch on the grounded slab (R=0\mathbf{R}=0) and the mutual coupling with neighboring cells (R≠0\mathbf{R}\ne0).

To evaluate R=0\mathbf{R}=0, the quasi-static kernel is expanded into a series of ground-plane images (Appendix A, (33)). The free-space self-interaction (n=0n=0) evaluates in closed form through Weber–Schafheitlin integrals [15]. The substrate image contributions (n≥1n\ge1) are exponentially damped by the round-trip distance 2nh2nh across the slab. Their remaining integrals are smooth one-dimensional spectral profiles, evaluated by exponentially convergent Gauss–Laguerre rules and in elementary closed form for the dominant dipole mode, so that the evaluation never resorts to a spatial mesh (Appendix B).

For R≠0\mathbf{R}\ne0, adjacent patches are disjoint. Under the ground-plane screening, a charge and its images form a neutral stack, so that the real-space kernel of (34) applied over the footprint of a neighboring cell behaves as that of a vertical dipole, smooth and decaying as ∣R∣−3|\mathbf{R}|^{-3} (Appendix A). Expanding this smooth interaction around each lattice vector, or equivalently the product of the two modal spectra into a Taylor series around k=0\mathbf{k}=0 in which each power kxikyjk_x^i k_y^j acts on the phase ejk⋅Re^{j\mathbf{k}\cdot\mathbf{R}} as the derivative (−j∂x)i(−j∂y)j(-j\partial_x)^i(-j\partial_y)^j, turns the mutual coupling into a convergent multipole series:

∑R≠0Wab(R)=∑i+j≤Kpijab(−j)i+j∑R≠0∂xi∂yjG(R).(14)\sum_{\mathbf{R}\ne0} W_{ab}(\mathbf{R}) = \sum_{i+j\le K} p_{ij}^{ab}(-j)^{i+j}\sum_{\mathbf{R}\ne0}\partial_x^i\partial_y^j G(\mathbf{R}). \tag*{(14)}

In this expression, the multipole moments pijabp_{ij}^{ab} are exact polynomials in (Ae,Be,cos⁡ψ,sin⁡ψ)(A_e,B_e,\cos\psi,\sin\psi) obtained algebraically from the Bessel power series of the disk modes, whereas the lattice sums ∑R≠0∂xi∂yjG(R)\sum_{\mathbf{R}\ne0}\partial_x^i\partial_y^jG(\mathbf{R}) depend only on the lattice periods and the substrate. The patch geometry is thus completely decoupled from the lattice summation, which makes it possible to precompute the lattice sums once and evaluate new patch geometries through simple polynomial contractions. These terms generalize the interaction constants of dipole-array models [22] to an arbitrary multipole order KK, and the convergence with respect to KK is quantified in § 5-C. The Taylor expansion converges when the disks circumscribing neighboring patches do not overlap (2Ae<min⁡R≠0∣R∣2A_e < \min_{\mathbf{R}\ne0}|\mathbf{R}|), a condition stricter than ellipse non-overlap when ψ≠0\psi\ne0 and satisfied by all the configurations of this paper. Details are given in Appendix B.

Inductive Extension

High-Frequency Inductive Effects

The quasi-static model describes the capacitive fringing fields, but the patch also carries surface currents that store magnetic energy. This inductive contribution is negligible at low frequency and progressively compensates the capacitive susceptance, which gives a series resonance at a frequency fresf_{\mathrm{res}} where Im⁡(Ys)→∞\operatorname{Im}(Y_s)\to\infty.

The Cardano model of Mencagli et al. [7] describes the grounded substrate by an equivalent unit-cell inductance Leq=(ϵr−1)μ0h/ϵrL_{\mathrm{eq}}=(\epsilon_r-1)\mu_0h/\epsilon_r. Together with the quasi-static capacitance C0,iC_{0,i} along the principal axis i∈{1,2}i\in\{1,2\} and the displacement capacitance of the slab ϵ0ϵrh/3\epsilon_0\epsilon_rh/3, it defines a reference frequency:

feq,i=12πLeq(C0,i+13ϵ0ϵrh).(15)f_{\mathrm{eq},i}=\frac{1}{2\pi\sqrt{L_{\mathrm{eq}}\left(C_{0,i}+\frac{1}{3}\epsilon_0\epsilon_rh\right)}}. \tag*{(15)}

The dynamic admittance of the Cardano model diverges at feq,if_{\mathrm{eq},i}, and the benchmarks adopt an empirical validity bound at 0.5 feq,i0.5\,f_{\mathrm{eq},i}, where its predictions depart from the full-wave reference. The physical resonance of the patch currents differs from this reference on elongated patches, whose longer major-axis current path stores more magnetic energy, and predicting it requires the dynamic current distribution and the retarded vector potential.

Mixed-Potential Integral Equation

At normal incidence, the vanishing tangential electric field on the patch gives the mixed-potential integral equation:

E0−∇sϕ(r)−jωAt(r)=0,(16)\mathbf{E}_0-\nabla_s\phi(\mathbf{r})-j\omega\mathbf{A}_t(\mathbf{r})=0, \tag*{(16)}

where ϕ\phi is the dynamic scalar potential produced by the surface charge σ\sigma and At\mathbf{A}_t is the in-plane vector potential produced by the surface current J\mathbf{J}. In the Floquet domain, each harmonic kmn\mathbf{k}_{mn} couples through the dynamic kernels G~ϕ(k,ω)\widetilde{G}_\phi(\mathbf{k},\omega) and G~A(k,ω)\widetilde{G}_A(\mathbf{k},\omega) of the grounded slab (Formulation C of Michalski and Mosig [17]), Appendix A), which include the retardation and the multiple reflections in the substrate and tend to the static kernels (3) when ω→0\omega\to0.

The average of the charge over the cell vanishes, σ^(0)=0\hat{\sigma}(0)=0, but the average of the current does not, J^(0)≠0\hat{\mathbf{J}}(0)\ne0. The harmonic k00\mathbf{k}_{00} is excluded from the dynamic potentials in (16), because the TEM propagation and the reflection on the ground plane are already included in the transmission-line model in which the sheet is embedded.

The surface current on the patch is decomposed into charge-carrying parts (gradients on the unit disk, mapped to the ellipse) and divergence-free (solenoidal) circulating parts. Divided by jωj\omega, the expansion reads:

J(r)jω=∑aqaJg,a(r)+∑bcbJs,b(r),(17)\frac{\mathbf{J}(\mathbf{r})}{j\omega}=\sum_a q_a\mathbf{J}_{g,a}(\mathbf{r})+\sum_b c_b\mathbf{J}_{s,b}(\mathbf{r}), \tag*{(17)}

where the charge-carrying currents Jg,a\mathbf{J}_{g,a} satisfy ∇⋅Jg,a=−σa\nabla\cdot\mathbf{J}_{g,a}=-\sigma_a, which ensures charge conservation for each electrostatic mode. The solenoidal currents Js,b\mathbf{J}_{s,b} are divergence-free (∇⋅Js,b=0\nabla\cdot\mathbf{J}_{s,b}=0) and have no normal flux across the patch contour (Js,b⋅n^=0\mathbf{J}_{s,b}\cdot\hat{\mathbf{n}}=0). Testing (16) with the current basis functions turns the scalar potential into the electric interaction matrix and the vector potential term jωAtj\omega\mathbf{A}_t into an ω2\omega^2 inductive term, which gives the block linear system:

[Mϕ(ω)−ω2MA,gg(ω)−ω2MA,gs(ω)−ω2MA,sg(ω)−ω2MA,ss(ω)][qc]=[d0].(18)\left[ \begin{array}{cc} \mathbf{M}_{\phi}(\omega)-\omega^2\mathbf{M}_{A,gg}(\omega) & -\omega^2\mathbf{M}_{A,gs}(\omega)\\ -\omega^2\mathbf{M}_{A,sg}(\omega) & -\omega^2\mathbf{M}_{A,ss}(\omega) \end{array} \right] \begin{bmatrix} \mathbf{q}\\ \mathbf{c} \end{bmatrix} = \begin{bmatrix} \mathbf{d}\\ \mathbf{0} \end{bmatrix}. \tag*{(18)}

where Mϕ(ω)\mathbf{M}_{\phi}(\omega) is the electric interaction matrix evaluated with the dynamic scalar kernel G~ϕ(k,ω)\widetilde{G}_{\phi}(\mathbf{k},\omega), d≡dphys\mathbf{d}\equiv\mathbf{d}_{\mathrm{phys}} is the incident projection matrix (11), and the magnetic interaction blocks are defined by:

MA,μνab(ω)=1S∑kmn≠0G~A(∣kmn∣,ω)[J^μ,a(kmn)]∗J^ν,b(kmn),(19)\mathbf{M}_{A,\mu\nu}^{ab}(\omega)=\frac{1}{S}\sum_{\mathbf{k}_{mn}\ne0}\widetilde{G}_A(|\mathbf{k}_{mn}|,\omega)[\hat{\mathbf{J}}_{\mu,a}(\mathbf{k}_{mn})]^*\hat{\mathbf{J}}_{\nu,b}(\mathbf{k}_{mn}), \tag*{(19)}

for μ,ν∈{g,s}\mu,\nu\in\{g,s\}. Because solenoidal modes carry no charge, they couple neither to the scalar potential nor to the uniform incident field (ds=0\mathbf{d}_s=0). The second row of (18) shows that the circulating currents are purely induced by the charge-carrying modes (c=−MA,ss−1MA,sgq\mathbf{c}=-\mathbf{M}_{A,ss}^{-1}\mathbf{M}_{A,sg}\mathbf{q}). Eliminating c\mathbf{c} folds their magnetic reaction into an effective 6×66\times6 system for the charge coefficients alone, with as many current modes as charge modes (§ 4-C):

[Mϕ(ω)−ω2MAeff(ω)]q=d,(20)[\mathbf{M}_{\phi}(\omega)-\omega^2\mathbf{M}_A^{\mathrm{eff}}(\omega)]\mathbf{q}=\mathbf{d}, \tag*{(20)}

with the effective magnetic interaction matrix:

MAeff(ω)=MA,gg(ω)−MA,gs(ω)MA,ss−1(ω)MA,sg(ω).(21)\mathbf{M}_A^{\mathrm{eff}}(\omega)=\mathbf{M}_{A,gg}(\omega)-\mathbf{M}_{A,gs}(\omega)\mathbf{M}_{A,ss}^{-1}(\omega)\mathbf{M}_{A,sg}(\omega). \tag*{(21)}

When ω→0\omega\to0, the inductive term ω2MAeff\omega^2\mathbf{M}_A^{\mathrm{eff}} vanishes and Mϕ(0)=M\mathbf{M}_{\phi}(0)=\mathbf{M}, so that (20) gives back the electrostatic system Mq=d\mathbf{M}\mathbf{q}=\mathbf{d}. Solving for q(ω)\mathbf{q}(\omega) at each frequency gives the sheet admittance tensor:

Ys(ω)=jωSdTq(ω).(22)\mathbf{Y}_{s}(\omega)=\frac{j\omega}{S}\mathbf{d}^{T}\mathbf{q}(\omega). \tag*{(22)}

The patch resonance fresf_{\mathrm{res}} is the pole of Ys\mathbf{Y}_{s}, where the sheet changes from capacitive to inductive (Im⁡(Zs)=0\operatorname{Im}(Z_s)=0). In contrast with fixed-profile circuit models [9], [10], the modal weights q(ω)\mathbf{q}(\omega) and c(ω)\mathbf{c}(\omega) are solved at each frequency, and the current profile on the patch changes with frequency.

The matrices Mϕ(ω)\mathbf{M}_{\phi}(\omega) and MA,μν(ω)\mathbf{M}_{A,\mu\nu}(\omega) are lattice sums of the same form as (10). Their static limits are evaluated as in Section III-E, with the kernel G~(k)\widetilde{G}(\mathbf{k}) for the scalar potential and the magnetostatic image kernel of Appendix A for the vector potential. For the magnetic blocks, the harmonic k00\mathbf{k}_{00} excluded in (19) has to be removed from the Poisson sum, since the mean current does not vanish. For two charge-carrying modes it equals μ0h da⋅db/S\mu_{0}h\,\mathbf{d}_{a}\cdot\mathbf{d}_{b}/S, where da\mathbf{d}_{a} is the aa-th row of dphys\mathbf{d}_{\mathrm{phys}} and G~A(0)=μ0h\widetilde{G}_{A}(0)=\mu_{0}h. By charge conservation, the spatial average of a charge-carrying current mode equals the dipole moment of its associated charge (J^g,a(0)=da\widehat{\mathbf{J}}_{g,a}(0)=\mathbf{d}_{a}), whereas solenoidal modes have zero mean current. Subtracting this k00\mathbf{k}_{00} term simply removes the parallel-plate inductance of the grounded slab, which is already accounted for by the transmission-line section hosting the sheet.

To avoid slow frequency-by-frequency Floquet summations, the dynamic matrices are evaluated via a two-term Kummer-type asymptotic extraction (Appendix A):

Mϕ(ω)=M+k02Mϕ(1)+ΔMϕ(ω),(23)\mathbf{M}_{\phi}(\omega)=\mathbf{M}+k_{0}^{2}\mathbf{M}_{\phi}^{(1)}+\Delta\mathbf{M}_{\phi}(\omega), \tag*{(23)}
MA,μν(ω)=MA,μν(0)+k02MA,μν(1)+ΔMA,μν(ω).(24)\mathbf{M}_{A,\mu\nu}(\omega)=\mathbf{M}_{A,\mu\nu}(0)+k_{0}^{2}\mathbf{M}_{A,\mu\nu}^{(1)}+\Delta\mathbf{M}_{A,\mu\nu}(\omega). \tag*{(24)}

Here, Mϕ(1)\mathbf{M}_{\phi}^{(1)} and MA,μν(1)\mathbf{M}_{A,\mu\nu}^{(1)} capture the leading frequency-independent retardation of the high-wavenumber Floquet tail and are precomputed once during unit-cell setup over a fixed grid (m2+n2≤122m^{2}+n^{2}\le12^{2}), whose convergence is quantified in Section V-D. Because the remaining dynamic kernels decay rapidly as k−5k^{-5}, the online residual blocks ΔMϕ(ω)\Delta\mathbf{M}_{\phi}(\omega) and ΔMA,μν(ω)\Delta\mathbf{M}_{A,\mu\nu}(\omega) require summing over only the twelve lowest Floquet harmonics (Nshell=2N_{\mathrm{shell}}=2, or 6 centrosymmetric pairs).

Current Modes on the Ellipse

Following the quasi-Helmholtz (loop–star) decomposition [30], the surface current on the canonical unit disk is split into charge-carrying modes (Jg,adisk=∇ρχ0,a\mathbf{J}_{g,a}^{\mathrm{disk}}=\nabla_{\rho}\chi_{0,a}, irrotational on the disk) and divergence-free solenoidal modes (Js,bdisk=z^×∇ρΨb\mathbf{J}_{s,b}^{\mathrm{disk}}=\hat{\mathbf{z}}\times\nabla_{\rho}\Psi_{b}). Enforcing zero normal current on the rim (ρ=1\rho=1) sets the boundary conditions: the potential χ0,a\chi_{0,a} satisfies the interior Neumann condition ∇2χ0,a=−σa\nabla^{2}\chi_{0,a}=-\sigma_{a} with ∂ρχ0,a∣ρ=1=0\left.\partial_{\rho}\chi_{0,a}\right|_{\rho=1}=0, while the stream function Ψb\Psi_{b} vanishes on the rim, Ψb∣ρ=1=0\left.\Psi_{b}\right|_{\rho=1}=0:

∇2χ0,a=−σa,∂ρχ0,a∣ρ=1=0,Ψb∣ρ=1=0.(25)\nabla^{2}\chi_{0,a}=-\sigma_{a},\qquad\left.\partial_{\rho}\chi_{0,a}\right|_{\rho=1}=0,\qquad\left.\Psi_{b}\right|_{\rho=1}=0. \tag*{(25)}

Retaining the same six angular-radial orders as in Section V-F yields Ng=6N_{g}=6 charge-carrying and Ns=6N_{s}=6 solenoidal modes. Section V-F quantifies the convergence of this truncation. The spatial potential χ0,a\chi_{0,a} never needs to be solved explicitly, since applying Green’s identity on the disk expresses J^g,a\widehat{\mathbf{J}}_{g,a} in closed form from the charge spectrum σ^a\widehat{\sigma}_{a} and a rim boundary term (Appendix C).

To transport these disk modes onto the physical patch, the current lines must follow the geometric stretching and rotation of the ellipse without creating artificial charge buildup on the rim. This is achieved through the affine transformation F=RψD\mathbf{F}=\mathbf{R}_{\psi}\mathbf{D}:

J(r)jω=RψDJdisk(ρ).(26)\frac{\mathbf{J}(\mathbf{r})}{j\omega}=\mathbf{R}_{\psi}\mathbf{D}\mathbf{J}_{\mathrm{disk}}(\boldsymbol{\rho}). \tag*{(26)}

with Jdisk=∑aqa∇ρχ0,a+∑bcbz^×∇ρΨb\mathbf{J}_{\mathrm{disk}}=\sum_{a}q_{a}\nabla_{\rho}\chi_{0,a}+\sum_{b}c_{b}\hat{\mathbf{z}}\times\nabla_{\rho}\Psi_{b}. Physically, scaling the current components by AeA_{e} and BeB_{e} stretches the current paths along the major axis and compresses them along the minor axis, which naturally accounts for the anisotropic magnetic energy storage discussed in Section IV-A. Since ∇r=RψD−1∇ρ\nabla_{\mathbf{r}}=\mathbf{R}_{\psi}\mathbf{D}^{-1}\nabla_{\rho}, this mapping preserves both the surface divergence (∇r⋅(J/jω)=∇ρ⋅Jdisk=−σdisk(ρ)\nabla_{\mathbf{r}}\cdot(\mathbf{J}/j\omega)=\nabla_{\rho}\cdot\mathbf{J}_{\mathrm{disk}}=-\sigma_{\mathrm{disk}}(\rho)) and the zero normal flux condition on the contour [18], so that σ(r)=σdisk(ρ)\sigma(\mathbf{r})=\sigma_{\mathrm{disk}}(\rho). Together with the surface element d2r=AeBe d2ρd^{2}r=A_{e}B_{e}\,d^{2}\rho, each spectral current mode on the ellipse follows as J^μ,a(k)=AeBeRψDJ^μ,adisk(k)\widehat{\mathbf{J}}_{\mu,a}(\mathbf{k})=A_{e}B_{e}\mathbf{R}_{\psi}\mathbf{D}\widehat{\mathbf{J}}_{\mu,a}^{\mathrm{disk}}(\mathbf{k}) (Appendix C), and charge conservation holds by construction in the spectral domain (jk⋅J^g,a(k)=−σ^a(k)j\mathbf{k}\cdot\widehat{\mathbf{J}}_{g,a}(\mathbf{k})=-\widehat{\sigma}_{a}(\mathbf{k})). The model remains a smooth function of the patch geometry.

For metasurface synthesis, it is also of interest to verify whether the principal axes of Ys(ω)\mathbf{Y}_{s}(\omega) rotate with frequency. On a representative patch tilted by ψ=30∘\psi=30^{\circ} with Ae/Be=2A_{e}/B_{e}=2, the rotation remains below 0.4∘0.4^{\circ} up to 35 GHz relative to the static capacitance axes, so the electrostatic principal axes can be used as a fixed eigenbasis across the operating band.

Numerical Validation

Consistency Checks

Before the full-wave comparisons, the formulation is checked against known limits. At ω→0\omega\to0, the dynamic kernels of Appendix A match the static kernel (3) with a relative difference below 10−1010^{-10}.

For an isolated patch in free space (d→∞d\to\infty, ϵr=1\epsilon_{r}=1, h→∞h\to\infty), where G~(k)→1/(2ϵ0k)\widetilde{G}(k)\to1/(2\epsilon_{0}k), the capacitance tensor is related to the polarizability volume αpol\boldsymbol{\alpha}_{\mathrm{pol}} by C=ϵ0αpol/S\mathbf{C}=\epsilon_{0}\boldsymbol{\alpha}_{\mathrm{pol}}/S. For a conducting ellipse with semi-axes Ae>BeA_{e}>B_{e} and e2=1−(Be/Ae)2e^{2}=1-(B_{e}/A_{e})^{2}, the Landau–Lifshitz polarizabilities along the principal axes are [27]:

αa=4π3Ae3e2K(e)−E(e),(27)\alpha_{a}=\frac{4\pi}{3}\frac{A_{e}^{3}e^{2}}{K(e)-E(e)}, \tag*{(27)}
αb=4π3Ae3e2E(e)/(1−e2)−K(e).\alpha_{b}=\frac{4\pi}{3}\frac{A_{e}^{3}e^{2}}{E(e)/(1-e^{2})-K(e)}.

where K(e)K(e) and E(e)E(e) are the complete elliptic integrals of the first and second kind of modulus ee (parameter m=e2m=e^{2}). With diso=10max⁡(Ae,Be)d_{\mathrm{iso}}=10\max(A_{e},B_{e}), the solver reproduces (27) within 0.2%, which is consistent with the residual dipolar coupling between neighboring cells at this spacing.

Full-Wave Periodic MoM Reference Solver

As a reference, a full-wave periodic Method of Moments (MoM) solver was implemented for planar metallic patches on a grounded dielectric slab. The patches are meshed with triangles supporting Rao–Wilton–Glisson (RWG) basis functions [31], and the periodic Green’s function of the slab is computed by a Floquet-mode summation accelerated with Kummer’s transformation [32, 33]. The sheet admittance tensor YsY_s is extracted from the reflection and transmission coefficients under normal incidence [5], and the quasi-static capacitance CC from the low-frequency slope of the susceptance (Ys≈jωCY_s \approx\mathrm{j}\omega C). Mesh convergence was checked with six mesh densities (from about 80 to more than 3000 unknowns), which also give the sequence used for the Richardson extrapolation.

A fine-mesh frequency sweep takes from several minutes to tens of minutes per unit cell on a standard workstation, whereas the proposed analytical model sets up a unit cell in under 25 ms and then evaluates each frequency point in about 0.6 ms (single core, Python implementation provided in [21]), which is roughly three orders of magnitude faster than full-wave sweeps.

Quasi-Static Capacitance Benchmark

The computational cost of Stage 1 is governed by the isolated-patch term (evaluated via analytical free-space integrals and 1-D damped image quadratures, Appendix B) and by the polynomial contraction of the neighbor series (14) with the precomputed lattice sums. These constants depend only on the lattice and on the substrate, and are computed once. With the Nb=6N_b = 6 basis functions and a multipole order of 30, the only truncation parameter, the capacitance tensor CC of a new patch is obtained in approximately 25 ms, and in about 0.6 s on the first call when the substrate lattice sums are precomputed from scratch.

The truncation to Nb=6N_b = 6 adopted in Section III is checked first. The 50 functions obtained for mmax⁡=9m_{\max} = 9 and qmax⁡=4q_{\max} = 4 serve as a converged reference, and the six-function subset reproduces it to within 0.5% on CC over the configurations of this section, with a median of 0.01%.

The MoM reference is then obtained by Richardson extrapolation (Figure 4). The capacitance follows a power law C(lc)=C∞+AlcαC(l_c) = C_{\infty} + A l_c^{\alpha} in the characteristic mesh size lcl_c, with a slow algebraic rate (α∼1.2\alpha\sim1.2–1.3) that reflects the difficulty of piecewise-linear RWG triangles in resolving the singular edge charge. The extrapolated continuum limit C∞C_{\infty} matches the analytical Galerkin solver within a fraction of a percent for all three configurations.

Figure 4. Convergence of the periodic MoM capacitance C0(lc)C_0(l_c) towards the proposed analytical Jacobi–Galerkin solver as the mesh size lcl_c is refined, for three elliptical patch aspect ratios on RO4003C (εr=3.55\varepsilon_r = 3.55, h=0.813h = 0.813 mm, d=4d = 4 mm, g/d=0.2g/d = 0.2). Top row: major eigenvalue C0,1C_{0,1} (power-law fitting exponent αmed=1.299\alpha_{\mathrm{med}} = 1.299). Bottom row: minor eigenvalue C0,2C_{0,2} (αmed=1.161\alpha_{\mathrm{med}} = 1.161).

The solver is then tested on the 100 configurations of Figure 5, a 5×55 \times5 grid of aspect ratios and normalized gaps spanning four substrate configurations. Among the 200 eigenvalues, 92% agree with the reference within ±1%\pm1\% and 75.5% within ±0.5%\pm0.5\%. The disagreements are not distributed at random. Indeed, 15 of the 16 eigenvalues outside ±1%\pm1\% are minor eigenvalues C0,2C_{0,2} on RO3010, the worst case reaching −2.31%-2.31\% for Ae/Be=2.5A_e/B_e = 2.5 and g/d=0.05g/d = 0.05. Refining the model itself (NbN_b to 50, more images, higher quadrature order and multipole order) moves these values by less than 0.01%, the multipole truncation contributing at most 0.3% in the tightest gap g/d=0.05g/d = 0.05. The residual discrepancy is therefore attributed to the convergence of the MoM reference, whose uncertainty can be estimated from the circular patch, for which the two axes should coincide and differ by about 0.3%.

Figure 5. Relative discrepancy ΔC0=(C0,MoM−C0,Galerkin)/C0,Galerkin×100%\Delta C_0 = (C_{0,\mathrm{MoM}} - C_{0,\mathrm{Galerkin}})/C_{0,\mathrm{Galerkin}} \times100\% between the proposed analytical Jacobi–Galerkin solver and the Richardson-extrapolated MoM reference across 100 benchmark configurations spanning five aspect ratios, five normalized gaps, and four substrate configurations (RT/duroid 5880: εr=2.2\varepsilon_r = 2.2, h=0.787h = 0.787 mm; RO4003C: εr=3.55\varepsilon_r = 3.55, h=0.813h = 0.813 and 1.5241.524 mm; RO3010: εr=10.2\varepsilon_r = 10.2, h=0.635h = 0.635 mm). Top: major eigenvalue C0,1C_{0,1}. Bottom: minor eigenvalue C0,2C_{0,2}.

Wideband Admittance Validation

The dispersive behavior is examined on the three geometries replicated from Figure 4. The eigenvalues Im⁡(Ys,1)(f)\operatorname{Im}(Y_{s,1})(f) and Im⁡(Ys,2)(f)\operatorname{Im}(Y_{s,2})(f) of the proposed model are compared in Figure 6 with the Cardano model [7] and the MoM reference. At low frequency, both analytical models coincide with the MoM data (jωC)(j\omega C). At $0.5f_{\mathrm{eq},i}$, the Cardano model already underestimates the MoM susceptance by 8 to 27%, with the largest deviation along the major axis of the Ae/Be=3A_e/B_e = 3 patch, whereas the proposed model remains within 0.6% of the reference and follows the full-wave data in the whole pre-resonance region. For the elongated patch (Ae/Be=3.0A_e/B_e = 3.0, panels (c) and (f)), the major-axis resonance fres,1f_{\mathrm{res},1} is below the reference frequency feq,1=37.7f_{\mathrm{eq},1} = 37.7 GHz. The proposed model places this resonant pole at 33.7 GHz, against 33.6 GHz for the MoM, whereas the Cardano model diverges at feq,1f_{\mathrm{eq},1}. For $A_e/B_e =

Figure 6. Dispersive sheet admittance eigenvalues Im⁡(Ys,1)(f)\operatorname{Im}(Y_{s,1})(f) (top row) and Im⁡(Ys,2)(f)\operatorname{Im}(Y_{s,2})(f) (bottom row) for the three representative unit-cell geometries of Figure 4 on RO4003C (εr=3.55\varepsilon_r = 3.55, h=0.813h = 0.813 mm, d=4d = 4 mm, g/d=0.2g/d = 0.2): Proposed analytical model (solid colored curves (22)), Mencagli et al. Cardano reference [7] (dashed), and Richardson-extrapolated periodic MoM (+ markers). The gray dotted lines mark the reference frequency 0.5feq,i0.5f_{\mathrm{eq},i}, (15) along each principal axis. The horizontal dashed line marks Im⁡(Ys)=0\operatorname{Im}(Y_s)=0.

2.0, the model follows the MoM data up to 60 GHz and gives the major-axis resonance at 35.1 GHz, where the Cardano singularity is at 34.4 GHz. Around 55–57 GHz, a sharp singularity appears in both the MoM data and the model. It corresponds to the guided-mode (Wood) anomaly [34], where the first Floquet harmonic, of wavenumber ∣k10∣=2π/d|k_{10}| = 2\pi/d, couples to the fundamental TM0_0 surface wave of the grounded slab. For the bare slab (h=0.813h = 0.813 mm, εr=3.55\varepsilon_r = 3.55), the TM0_0 dispersion equation kztan⁡(kzh)=εrkρ2−k02k_z \tan(k_z h) = \varepsilon_r \sqrt{k_\rho^2-k_0^2}, with kz=εrk02−kρ2k_z = \sqrt{\varepsilon_r k_0^2-k_\rho^2}, gives (kρ)TM0=2π/d(k_\rho)_{\mathrm{TM0}} = 2\pi/d at f≈55.1f \approx55.1 GHz. In the model, this interaction is carried by the first Floquet harmonics of the retardation sum. Retaining 12 harmonics (Nshell=2N_{\mathrm{shell}} = 2, 6 centrosymmetric pairs) places the anomaly within 0.4 GHz of the MoM data for all three geometries, and the resonance positions of Figure 6 and Figure 8 directly validate this truncation. The precomputed retardation grid m2+n2≤122m^2+n^2 \le12^2 was checked against m2+n2≤242m^2+n^2 \le24^2, which moves the admittance eigenvalues by less than 0.003% up to 0.95fres,10.95 f_{\mathrm{res},1}.

Figure 8. Dispersive sheet admittance eigenvalues for a strongly elongated patch rotated by ψ=45∘\psi= 45^\circ on high-permittivity Rogers RO3010 (ϵr=10.2\epsilon_r = 10.2, h=0.635h = 0.635 mm, d=4d = 4 mm, Ae=1.60A_e = 1.60 mm, Be=0.53B_e = 0.53 mm, g/d=0.20g/d = 0.20 at ψ=0∘\psi= 0^\circ): (a) Im⁡(Ys,1)(f)\operatorname{Im}(Y_{s,1})(f), (b) Im⁡(Ys,2)(f)\operatorname{Im}(Y_{s,2})(f). Proposed analytical model (solid red), Mencagli et al. Cardano model [7] using rotated static capacitance (dashed gray), and Richardson-extrapolated periodic MoM (+ markers). The gray dotted lines mark 0.5feq,i0.5 f_{\mathrm{eq},i} (15). Insets in the bottom-left corner show the unit cell and the rotated patch geometry.

Surface-Wave Reactance

The sheet admittance is now used to compute the surface-wave reactance. For propagation along a principal axis, the wavenumber kρk_\rho of the fundamental TM surface wave follows from the transverse-resonance condition [7, 35]:

YupTM(kρ,ω)+YdownTM(kρ,ω)+Ys,i(ω)=0(28)Y_{\mathrm{up}}^{\mathrm{TM}}(k_\rho,\omega)+Y_{\mathrm{down}}^{\mathrm{TM}}(k_\rho,\omega)+Y_{\mathrm{s},i}(\omega)=0 \tag*{(28)}

where YupTM=jωε0/kρ2−k02Y_{\mathrm{up}}^{\mathrm{TM}}=j\omega\varepsilon_0/\sqrt{k_\rho^2-k_0^2} is the admittance of the air half-space and YdownTM=−jωε0εr/kzcot⁡(kzh)Y_{\mathrm{down}}^{\mathrm{TM}}=-j\omega\varepsilon_0\varepsilon_r/k_z\cot(k_z h), with kz=k02εr−kρ2k_z=\sqrt{k_0^2\varepsilon_r-k_\rho^2}, the admittance of the grounded slab. The TM surface reactance is Xsurf,i=kρ2−k02/(ωε0)=η0κTM,i2−1X_{\mathrm{surf},i}=\sqrt{k_\rho^2-k_0^2}/(\omega\varepsilon_0)=\eta_0\sqrt{\kappa_{\mathrm{TM},i}^2-1}, with κTM,i=kρ/k0\kappa_{\mathrm{TM},i}=k_\rho/k_0.

TM surface reactance is Xsurf,i=kρ2−k02/(ωε0)=η0κTM,i2−1X_{\mathrm{surf},i}=\sqrt{k_\rho^2-k_0^2}/(\omega\varepsilon_0)=\eta_0\sqrt{\kappa_{\mathrm{TM},i}^2-1}, with κTM,i=kρ/k0\kappa_{\mathrm{TM},i}=k_\rho/k_0. Figure 7 compares the surface reactance for the three geometries. The MoM points are obtained by solving (28) with the sheet admittance extracted from normal-incidence MoM simulations. For the circular patch, both axes give the same reactance, which follows the MoM data. When the aspect ratio increases, the surface wave becomes anisotropic: for Ae/Be=3.0A_e/B_e=3.0, the ratio Xsurf,1/Xsurf,2X_{\mathrm{surf},1}/X_{\mathrm{surf},2} is about 2.5 at 30 GHz (and 1.8 at 25 GHz).

Figure 7. TM surface reactance Xsurf,i(f)X_{\mathrm{surf},i}(f) from the transverse-resonance condition for the three representative geometries of Figure 6 on RO4003C (εr=3.55\varepsilon_r = 3.55, h=0.813h = 0.813 mm, d=4d = 4 mm, g/d=0.2g/d = 0.2): (a)–(c) major axis, (d)–(f) minor axis. Proposed analytical model (solid colored curves), Mencagli et al. Cardano reference [7] (dashed), and Richardson-extrapolated MoM (+ markers). The dash-dotted line marks the first Brillouin zone boundary XBZ(f)X_{\mathrm{BZ}}(f), and the shaded region indicates the domain outside the first Brillouin zone (kρ≥π/dk_\rho\ge\pi/d, homogenized model not applicable), where model curves transition to dotted lines. The gray dotted lines mark 0.5feq,i0.5 f_{\mathrm{eq},i} (15).

Inside the first Brillouin zone (kρ≤π/dk_\rho\le\pi/d), the surface wave remains uncoupled from diffraction orders. With kρ/k0=1+(Xsurf,i/η0)2k_\rho/k_0=\sqrt{1+(X_{\mathrm{surf},i}/\eta_0)^2}, this boundary corresponds to the edge reactance

XBZ(f)=η0(c2fd)2−1,(29)X_{\mathrm{BZ}}(f)=\eta_0\sqrt{\left(\frac{c}{2fd}\right)^2-1}, \tag*{(29)}

shown as a dash-dotted line in Figure 7. Beyond it, the region is shaded and curves are dotted, since the homogenized model does not describe an unattenuated guided mode there (for d=4d=4 mm, the light line reaches the zone edge at f=c/(2d)=37.5f=c/(2d)=37.5 GHz).

Rotated High-Permittivity Benchmark

To test the model in a demanding case, a patch combining several difficulties is considered: the most elongated geometry of this study (Ae=1.60A_e=1.60 mm, Be=0.53B_e=0.53 mm, Ae/Be≈3.0A_e/B_e\approx3.0, d=4.0d=4.0 mm, corresponding to g/d=0.20g/d=0.20 at ψ=0∘\psi=0^\circ) on the highest-permittivity substrate (Rogers RO3010, εr=10.2\varepsilon_r=10.2, h=0.635h=0.635 mm), rotated by ψ=45∘\psi=45^\circ. This orientation gives a strong coupling along the diagonals of the square lattice. and non-zero off-diagonal entries of the tensor. The case also serves to quantify the truncation of the current basis adopted in Section IV-C. Doubling NgN_g and NsN_s shifts the fundamental resonance by less than 1 MHz.

Figure 8 shows the eigenvalues (a) Im⁡(Ys,1)(f)\operatorname{Im}(Y_{s,1})(f) and (b) Im⁡(Ys,2)(f)\operatorname{Im}(Y_{s,2})(f) up to 50 GHz. In panel (a), the model places the fundamental resonance at 20.7 GHz, within 0.5 GHz of the MoM value of 20.2 GHz, and follows the capacitive-to-inductive transition of the reference. The higher-order substrate-coupled resonance is also reproduced, at 44.5 GHz against 45.1 GHz for the MoM. The Cardano model [7], even with the exact rotated static capacitance C0,1=40.35C_{0,1} = 40.35 fF, deviates from the MoM data by 30% at 0.5feq,1=12.160.5 f_{\mathrm{eq},1} = 12.16 GHz, diverges at feq,1=24.33f_{\mathrm{eq},1} = 24.33 GHz, which is 3.6 GHz above the resonance of the model, and does not reproduce the higher-order resonance. In panel (b), the MoM gives the transverse resonance at 36.5 GHz, and the model at 35.3 GHz. The Cardano model deviates from the reference by 12% at 0.5feq,2=18.480.5 f_{\mathrm{eq},2} = 18.48 GHz.

Conclusion

Synthesizing a holographic metasurface means prescribing an admittance tensor for every cell of an aperture, and each prescription asks for a forward model of the local geometry. Full-wave simulation is too expensive for this inverse problem, and the semi-analytical models available for elliptical patches pay for their speed with a quasi-static capacitance extracted from full-wave data or from an equivalent rectangular gap, and with a single current mode per eigenaxis that departs from the reference well before the patch resonance. The model proposed in this paper takes the direct route: the Galerkin method is applied to the geometry of the patches themselves, without spatial meshing. The restriction to elliptical cells is what makes this possible. A rotated ellipse is an affine image of a circle, so the whole formulation lives on the canonical unit disk, with a tailored basis that absorbs the edge singularity and essentially amounts to cylindrical modes with closed-form Fourier spectra. Everything follows from these spectra: the capacitance tensor, the dispersive admittance and the surface-wave response, the lattice being reduced to an isolated-patch term and a multipole series, with no truncated Floquet summation.

Compared with a Richardson-extrapolated periodic Method of Moments, the model predicts the static capacitance within 1% for 92% of 200 tested eigenvalues, follows the dispersive admittance up to the fundamental resonance, including the capacitive-to-inductive transition on elongated patches, and captures the substrate guided-mode anomaly, where the single-mode Cardano reference diverges. A wideband response evaluates in a few tens of milliseconds, where the periodic full-wave solvers of FEM or spectral MoM type need minutes to tens of minutes.

These results open several practical perspectives. The admittance tensor gives the three quantities a unit cell is used for: the surface-wave dispersion, through the transverse-resonance condition, and the reflection and transmission of a normal-incidence plane wave, through a simple parallel combination of the sheet with the substrate response. Any other substrate is treated the same way, multilayer stacks included, since transfer-matrix methods keep the corresponding Green's kernels in closed form, and reflect- and transmittary cells therefore follow without additional effort. With such evaluation times, the admittance tables of a complete aperture become routine to build, rather than requiring one full-wave simulation per cell. The model is also an explicit function of the geometry, and therefore differentiable: this makes it a natural building block for end-to-end differentiable design tools. The continuation of this work is to propose such tools to the community, so that apertures very large compared with the operating wavelength can be optimized in real time. Finally, extending this mesh-free spectral approach to the all-dielectric structures that dominate photonics is a natural perspective. It requires replacing the PEC Meixner edge basis with volumetric polarization currents, and accounting for the Mie resonances that appear when the cells approach the half-wavelength regime.

Acknowledgment

Large language models (Claude, Anthropic) were used as auxiliary tools for cross-checking intermediate symbolic results, locating integrals and identities in the literature, code development, and language refinement. All theoretical derivations, implementations, and interpretations were developed and verified by the author, who assumes full responsibility for the contents of this paper.

Appendix A: Spectral Green's Kernels and Static Limit

Dynamic Transmission-Line Kernels

The structure is made of air (z>0z > 0, permittivity ε0\varepsilon_0), a dielectric substrate (−h<z<0-h < z < 0, permittivity ε0εr\varepsilon_0\varepsilon_r) and a perfect electric conductor (PEC) ground plane at z=−hz = -h. Following Michalski and Mosig [17], which extends the single-layer mixed-potential formulation of Mosig [23], the spectral kernels of the vector and scalar potentials at the interface z=0z = 0 are, with the ejωte^{j\omega t} convention:

G~A(k,ω)=μ0κ0+κscoth⁡(κsh),(30)\widetilde{G}_A(k,\omega) = \frac{\mu_0}{\kappa_0+\kappa_s\coth(\kappa_s h)}, \tag*{(30)}
G~ϕ(k,ω)=1ε0k2[κ0κsκs+εrκ0coth⁡(κsh)+k02κ0+κscoth⁡(κsh)],(31)\widetilde{G}_{\phi}(k,\omega) = \frac{1}{\varepsilon_0 k^2}\left[\frac{\kappa_0\kappa_s}{\kappa_s+\varepsilon_r\kappa_0\coth(\kappa_s h)}+\frac{k_0^2}{\kappa_0+\kappa_s\coth(\kappa_s h)}\right], \tag*{(31)}

where k=∣k∣k = \lvert\mathbf{k}\rvert, k0=ω/ck_0 = \omega/c, and κ0=k2−k02\kappa_0 = \sqrt{k^2-k_0^2} and κs=k2−εrk02\kappa_s = \sqrt{k^2-\varepsilon_r k_0^2} are the vertical propagation constants in air and in the substrate. For the non-zero harmonics, κ0\kappa_0 is real in the frequency range considered (f<c/d=75f < c/d = 75 GHz for d=4d = 4 mm), and the substrate terms are even functions of κs\kappa_s, so that no choice of branch is needed. The denominator of (31) has a real pole when a Floquet harmonic matches the TM0_0 guided mode of the slab (§ 5-D). With a lossy substrate this pole moves into the complex plane, and in the lossless case the frequency sampling avoids the exact pole.

Quasi-Static Limit and Image Series

When k0→0k_0 \to0, κ0→k\kappa_0 \to k and κs→k\kappa_s \to k. The vector potential kernel (30) becomes

G~A(k)∣k0→0=μ0k(1+coth⁡(kh))=μ02k(1−e−2kh),(32)\left.\widetilde{G}_A(k)\right|_{k_0\to0} = \frac{\mu_0}{k(1+\coth(kh))} = \frac{\mu_0}{2k}\left(1-e^{-2kh}\right), \tag*{(32)}

which is the magnetostatic image kernel, the term −e−2kh-e^{-2kh} being the negative current image at z=−2hz=-2h. In the scalar kernel (31), the retarded term in k02k_0^2 vanishes and the first term gives the electrostatic kernel (3) of Mosig [23]. With coth⁡(kh)=(1+e−2kh)/(1−e−2kh)\coth(kh)=(1+e^{-2kh})/(1-e^{-2kh}) and Γ=(εr−1)/(εr+1)\Gamma=(\varepsilon_r-1)/(\varepsilon_r+1), this kernel is expanded in a geometric series of images,

G~(k)=1ε0(1+εr)k[1+∑n≥1cne−2nkh],(33)\widetilde{G}(k)=\frac{1}{\varepsilon_0(1+\varepsilon_r)k}\left[1+\sum_{n\geq1}c_n e^{-2nkh}\right], \tag*{(33)}

with cn=−(1+Γ)(−Γ)n−1c_n=-(1+\Gamma)(-\Gamma)^{n-1}, whose terms are the kernel of a homogeneous medium of permittivity (1+εr)/2(1+\varepsilon_r)/2 and the images of the charge in the ground plane, reflected at the dielectric interface with the coefficient Γ\Gamma. Since ∑ncn=−1\sum_n c_n=-1, the leading 1/r1/r behavior cancels in the real-space kernel

G(r)=12πε0(1+εr)[1r+∑n=1∞cnr2+4n2h2],(34)G(r)=\frac{1}{2\pi\varepsilon_0(1+\varepsilon_r)}\left[\frac{1}{r}+\sum_{n=1}^{\infty}\frac{c_n}{\sqrt{r^2+4n^2h^2}}\right], \tag*{(34)}

which decays as r−3r^{-3} because of the screening by the ground plane. The same transformation applied to the magnetostatic kernel gives GA(r)=(μ0/4π)[1/r−(r2+4h2)−1/2]G_A(r)=(\mu_0/4\pi)[1/r-(r^2+4h^2)^{-1/2}], which does not depend on εr\varepsilon_r.

Asymptotic Extraction and Dynamic Convergence

Following standard Kummer-type acceleration [32, 33], the slow high-wavenumber tail of the dynamic Floquet sum is extracted analytically. For k≫k0k \gg k_0, the dynamic kernels separate into the quasi-static kernels of the previous subsection and a frequency-independent retardation correction:

G~ϕ,A(k,ω)≈G~ϕ,Aqs(k)+k02g~ϕ,A(1)(k),(35)\widetilde{G}_{\phi,A}(k,\omega)\approx\widetilde{G}_{\phi,A}^{\mathrm{qs}}(k)+k_0^2\widetilde{g}_{\phi,A}^{(1)}(k), \tag*{(35)}

where g~ϕ,A(1)(k)=∂G~ϕ,A/∂(k02)∣k0=0\widetilde{g}_{\phi,A}^{(1)}(k)=\left.\partial\widetilde{G}_{\phi,A}/\partial(k_0^2)\right|_{k_0=0} follows by direct differentiation of (30)–(31). This correction is pre-integrated once into the setup matrices Mϕ(1)\mathbf{M}_{\phi}^{(1)} and MA,μν(1)\mathbf{M}_{A,\mu\nu}^{(1)}, over a fixed Floquet grid (m2+n2≤122m^2+n^2\leq12^2). Once it is subtracted, the residual part of the sum decays fast enough that the frequency-dependent summation is restricted to the twelve lowest harmonics (Nshell=2N_{\mathrm{shell}}=2, or 6 centrosymmetric pairs). These harmonics include the substrate guided-mode poles (TM0_0 Wood anomalies), which are therefore still captured, in under 1 ms per frequency point.

Appendix B: Jacobi Basis, Analytical Spectra, and Lattice Sum

Under the radial substitution u=2ρ2−1u=2\rho^2-1, the basis functions (5) are orthogonal on the unit disk with respect to the regularizing edge weight (1−ρ2)1/2(1-\rho^2)^{1/2}. Standard Jacobi polynomial orthogonality [26] directly yields the closed-form modal norm:

Nm,q2=12(2q+m+1/2)Γ(q+1/2)Γ(q+m+1)q! Γ(q+m+1/2),(36)N_{m,q}^2=\frac{1}{2(2q+m+1/2)}\frac{\Gamma(q+1/2)\Gamma(q+m+1)}{q!\,\Gamma(q+m+1/2)}, \tag*{(36)}

with N1,0=2/3N_{1,0}=\sqrt{2/3} (3N1,0=63N_{1,0}=\sqrt{6}) for the fundamental dipole mode.

Analytical Fourier Spectra

In the disk frame κ=DRψTk=κ(cos⁡θκ,sin⁡θκ)\boldsymbol{\kappa}=\mathbf{D}\mathbf{R}_{\psi}^{T}\mathbf{k}=\kappa(\cos\theta_{\kappa},\sin\theta_{\kappa}), expanding the Fourier kernel e−jκ⋅ρe^{-j\boldsymbol{\kappa}\cdot\boldsymbol{\rho}} into cylindrical harmonics via the Jacobi–Anger identity [28] and integrating over θ\theta selects the angular order mm and gives the factorized form (7). The remaining radial Hankel transform is a Sonine–Schläfli integral tabulated in [36] and widely used in Jacobi–Bessel aperture theory [14, 29]:

∫01xm+1(1−x2)αPq(α,m)(2x2−1)Jm(κx) dx=(−1)q2αΓ(q+α+1)q!κ−α−1Jm+2q+α+1(κ),(37)\int_0^1 x^{m+1}(1-x^2)^\alpha P_q^{(\alpha,m)}(2x^2-1)J_m(\kappa x)\,dx =(-1)^q2^\alpha\frac{\Gamma(q+\alpha+1)}{q!}\kappa^{-\alpha-1}J_{m+2q+\alpha+1}(\kappa), \tag*{(37)}

valid for α>−1\alpha>-1, with the argument convention Pq(α,m)(2x2−1)=(−1)qPq(m,α)(1−2x2)P_q^{(\alpha,m)}(2x^2-1)=(-1)^qP_q^{(m,\alpha)}(1-2x^2) relative to the tabulated form. Setting α=−1/2\alpha=-1/2 (Meixner charge weight) and using Jn(κ)=π/(2κ)Jn+1/2(κ)J_n(\kappa)=\sqrt{\pi/(2\kappa)}J_{n+1/2}(\kappa) directly gives the closed-form charge spectrum (8). Setting α=+1/2\alpha=+1/2 similarly gives the solenoidal structure-function spectrum in Appendix C.

Isolated-Patch Term and Neighbor Series

Because the real-space kernel (34) decays as r−3r^{-3} and the modal spectra are band-limited by the patch size, the Poisson lattice sum (13) is absolutely convergent.

Isolated-patch term (R=0\mathbf{R} = 0). In the disk frame, the change of variables to κ\boldsymbol{\kappa} gives d2k=d2κ/(AeBe)d^{2}k = d^{2}\kappa/(A_{\mathrm{e}}B_{\mathrm{e}}) and ∣k∣=κ g(θκ)|\mathbf{k}| = \kappa\,g(\theta_{\kappa}), with g(θκ)=cos⁡2θκ/Ae2+sin⁡2θκ/Be2g(\theta_{\kappa}) = \sqrt{\cos^{2}\theta_{\kappa}/A_{\mathrm{e}}^{2} + \sin^{2}\theta_{\kappa}/B_{\mathrm{e}}^{2}}. Substituting the image series (33) separates the self-interaction into radial and angular integrals:

Wab(0)=1(2π)2AeBe ε0(1+εr)∑n≥0cn∫02πdθκg(θκ)∫0∞dκ [σ^a∗σ^b](κ,θκ)e−2nhg(θκ)κ,c0=1.(38)W_{ab}(\mathbf{0}) = \frac{1}{(2\pi)^{2}A_{\mathrm{e}}B_{\mathrm{e}}\,\varepsilon_{0}(1+\varepsilon_{r})}\sum_{n\geq0}c_{n}\int_{0}^{2\pi}\frac{d\theta_{\kappa}}{g(\theta_{\kappa})}\int_{0}^{\infty}d\kappa\,[\hat{\sigma}_{a}^{*}\hat{\sigma}_{b}](\kappa,\theta_{\kappa})e^{-2nhg(\theta_{\kappa})\kappa},\qquad c_{0}=1. \tag*{(38)}

For both charge and current modes, the radial integrand reduces to a finite sum of Bessel products κ−γJμ(κ)Jν(κ)\kappa^{-\gamma}J_{\mu}(\kappa)J_{\nu}(\kappa). For the free-space term (n=0n=0), the radial integral over [0,∞)[0,\infty) evaluates in closed form via the Weber–Schafheitlin integral in terms of Gamma functions [28 Sec. 13.41], as in open circular microstrip analysis [15]. For the substrate images (n≥1n\geq1), the exponential damping e−2nhg(θκ)κe^{-2nhg(\theta_{\kappa})\kappa} allows a fast evaluation of the radial integral via a 32-node Gauss–Laguerre quadrature (or in elementary closed form for the dipole mode). The remaining smooth periodic integral over θκ∈[0,2π)\theta_{\kappa}\in[0,2\pi) is then evaluated by the trapezoidal rule.

Neighbor series (R≠0\mathbf{R}\ne\mathbf{0}). For disjoint patches, the mutual interaction is governed by the low-wavenumber behavior of the modal spectra around κ=0\kappa=0. Because Jm+2q(κ)/κmJ_{m+2q}(\kappa)/\kappa^{m} and Jm±1(κ)/κm±1J_{m\pm1}(\kappa)/\kappa^{m\pm1} are even entire functions of κ=κx2+κy2\kappa=\sqrt{\kappa_{x}^{2}+\kappa_{y}^{2}} and κmejmθκ=(κx+jκy)m\kappa^{m}e^{jm\theta_{\kappa}}=(\kappa_{x}+j\kappa_{y})^{m} is a homogeneous polynomial, expanding the Bessel functions in power series [28] expresses every charge and current spectrum on the unit disk as an exact bivariate Taylor series in (κx,κy)(\kappa_{x},\kappa_{y}) with closed-form rational coefficients. Multiplying the expansions of modes aa and bb up to total degree KK and mapping to the lattice frame via κ=DRψTk\boldsymbol{\kappa}=\mathbf{D}\mathbf{R}_{\psi}^{T}\mathbf{k} gives the multipole coefficients pijabp_{ij}^{ab} in (14) by binomial algebra. In (13), each monomial kxikyjk_{x}^{i}k_{y}^{j} acts on ejk⋅Re^{j\mathbf{k}\cdot\mathbf{R}} as (−j∂x)i(−j∂y)j(-j\partial_{x})^{i}(-j\partial_{y})^{j}, which transfers the derivatives onto the real-space image kernel (34). The lattice derivatives are computed from the algebraic recurrence obtained by differentiating (r2+z2)u2=1(r^{2}+z^{2})u^{2}=1 on the Taylor coefficients of u=(r2+z2)−1/2u=(r^{2}+z^{2})^{-1/2}, and summed over 24 lattice periods with an analytical integral remainder.

Appendix C: Current Modes and Closed-Form Spectra

Charge-Carrying Currents

For an electrostatic mode σa(ρ,θ)=Rm,q(ρ)cos⁡(mθ)\sigma_{a}(\rho,\theta)=R_{m,q}(\rho)\cos(m\theta), the potential in (25) separates as χ0,a(ρ,θ)=gm,q(ρ)cos⁡(mθ)\chi_{0,a}(\rho,\theta)=g_{m,q}(\rho)\cos(m\theta). Rather than solving (25) in space, the current spectrum J^g,adisk(κ)\hat{\mathbf{J}}_{g,a}^{\mathrm{disk}}(\boldsymbol{\kappa}) is obtained in closed form by decomposing it into longitudinal (along κ^\hat{\boldsymbol{\kappa}}) and transverse components. Because the normal current ∂ρχ0,a\partial_{\rho}\chi_{0,a} vanishes on the rim, the longitudinal component is fixed directly by charge conservation (jκ⋅J^g,adisk=−σ^adisk)(j\boldsymbol{\kappa}\cdot\hat{\mathbf{J}}_{g,a}^{\mathrm{disk}}=-\hat{\sigma}_{a}^{\mathrm{disk}}), while Green’s identity on the disk shows that the transverse component stems solely from the rim value gm,q(1)g_{m,q}(1):

J^g,adisk(κ)=jκκ2σ^adisk(κ)+BT(κ),(39)\hat{\mathbf{J}}_{g,a}^{\mathrm{disk}}(\boldsymbol{\kappa})=\frac{j\boldsymbol{\kappa}}{\kappa^{2}}\hat{\sigma}_{a}^{\mathrm{disk}}(\boldsymbol{\kappa})+\mathbf{B}_{T}(\boldsymbol{\kappa}), \tag*{(39)}

where BT=B−κ^(κ^⋅B)\mathbf{B}_{T}=\mathbf{B}-\hat{\boldsymbol{\kappa}}(\hat{\boldsymbol{\kappa}}\cdot\mathbf{B}) is the transverse projection of the contour integral B(κ)=∮ρ=1χ0,an^e−jκ⋅p dl\mathbf{B}(\boldsymbol{\kappa})=\oint_{\rho=1}\chi_{0,a}\hat{\mathbf{n}}e^{-j\boldsymbol{\kappa}\cdot\mathbf{p}}\,dl. By Jacobi polynomial orthogonality, the rim potential vanishes for all higher radial orders (gm,q(1)=0g_{m,q}(1)=0 for q≥1q\geq1, so that these currents are purely longitudinal) and equals gm,0(1)=π Γ(m+1)/[2mNm,0Γ(m+3/2)]g_{m,0}(1)=\sqrt{\pi}\,\Gamma(m+1)/[2^{m}N_{m,0}\Gamma(m+3/2)] for q=0q=0. For the cosine family, expanding the rim integral via the Jacobi–Anger identity gives:

Bx=πgm,0(1)[(−j)m+1Jm+1(κ)cos⁡(m+1)θκ+(−j)m−1Jm−1(κ)cos⁡(m−1)θκ],(40)B_{x}=\pi g_{m,0}(1)\left[(-j)^{m+1}J_{m+1}(\kappa)\cos(m+1)\theta_{\kappa}+(-j)^{m-1}J_{m-1}(\kappa)\cos(m-1)\theta_{\kappa}\right], \tag*{(40)}

with ByB_{y} obtained by replacing cos⁡(m±1)θκ\cos(m\pm1)\theta_{\kappa} with ±sin⁡(m±1)θκ\pm\sin(m\pm1)\theta_{\kappa} (and similarly for the sine family).

Although the longitudinal term in (39) contains an apparent 1/κ21/\kappa^{2} factor, the total spectrum J^g,adisk(κ)\hat{\mathbf{J}}_{g,a}^{\mathrm{disk}}(\boldsymbol{\kappa}) is regular at κ=0\kappa=0 because the spatial current is confined to the unit disk. Specifically, for q≥1q\geq1 the charge spectrum vanishes as κm+2q\kappa^{m+2q}, whereas for q=0q=0 the apparent κm−1\kappa^{m-1} divergence of the longitudinal part is canceled by the leading Taylor term of the boundary contribution BT(κ)\mathbf{B}_{T}(\boldsymbol{\kappa}) in (40). At κ=0\kappa=0, only the dipole mode (m,q)=(1,0)(m,q)=(1,0) remains non-zero and gives back the static dipole moment da\mathbf{d}_{a} after applying the affine mapping (26).

Solenoidal Currents

The solenoidal modes Js,bdisk=z^×∇ρΨb\mathbf{J}_{s,b}^{\mathrm{disk}}=\hat{\mathbf{z}}\times\nabla_{\rho}\Psi_{b} describe closed current loops circulating within the patch. Requiring zero normal flux across the boundary means that the stream function Ψb\Psi_{b} must be constant (and thus set to zero) along the rim ρ=1\rho=1, while its radial derivative must reproduce the (1−ρ2)−1/2(1-\rho^{2})^{-1/2} Meixner singularity of the tangential edge current. Both physical conditions are satisfied by choosing:

Ψm,qc/s(ρ)=ρm(1−ρ2)1/2Pq(1/2,m)(2ρ2−1){cos⁡mθsin⁡mθ,(41)\Psi_{m,q}^{c/s}(\rho)=\rho^{m}(1-\rho^{2})^{1/2}P_{q}^{(1/2,m)}(2\rho^{2}-1)\left\{\begin{array}{c}\cos m\theta\\ \sin m\theta\end{array}\right., \tag*{(41)}

for odd m∈{1,3,…,mmax⁡}m\in\{1,3,\ldots,m_{\max}\} and q∈{0,…,qmax⁡}q\in\{0,\ldots,q_{\max}\}. Because Ψb\Psi_{b} vanishes on the rim, integration by parts introduces no boundary contour term and yields J^s,bdisk=j(−κy,κx)Ψ^b\hat{\mathbf{J}}_{s,b}^{\mathrm{disk}}=j(-\kappa_{y},\kappa_{x})\hat{\Psi}_{b}, where Ψ^b\hat{\Psi}_{b} follows directly from (37) with α=1/2\alpha=1/2:

Ψ^m,qc(κ)=2π(−j)mcos⁡(mθκ) cqJm+2q+1(κ)κ,(42)\hat{\Psi}_{m,q}^{c}(\boldsymbol{\kappa})=2\pi(-j)^{m}\cos(m\theta_{\kappa})\,c_{q}\frac{J_{m+2q+1}(\kappa)}{\kappa}, \tag*{(42)}

with cq=(−1)q(2qq)(2q+1)4−qc_{q}=(-1)^{q}\binom{2q}{q}(2q+1)4^{-q} (c0=1c_{0}=1, c1=−3/2c_{1}=-3/2, c2=15/8,…c_{2}=15/8,\ldots), and the sine family obtained by replacing cos⁡mθκ\cos m\theta_{\kappa} with sin⁡mθκ\sin m\theta_{\kappa}. As for the charge-carrying modes, the physical spectrum Js,b(k)\mathbf{J}_{s,b}(\mathbf{k}) on the rotated ellipse follows from the affine mapping (26) by scaling the components by (Ae,Be)(A_{\mathrm{e}},B_{\mathrm{e}}) and multiplying by the Jacobian AeBeA_{\mathrm{e}}B_{\mathrm{e}}.

References

References

  1. [1]B. H. Fong, J. S. Colburn, J. J. Ottusch, J. L. Visher, and D. F. Sievenpiper, “Scalar and tensor holographic artificial impedance surfaces,” IEEE Transactions on Antennas and Propagation, vol. 58, no. 10, pp. 3212–3221, Oct. 2010.DOI
  2. [2]A. M. Patel and A. Grbic, “Modeling and analysis of printed-circuit tensor impedance surfaces,” IEEE Transactions on Antennas and Propagation, vol. 61, no. 1, pp. 211–220, Jan. 2013.DOI
  3. [3]M. Faenzi, G. Minatti, D. González-Ovejero, F. Caminita, E. Martini, C. Delia Giovampaola, and S. Maci, “Metasurface antennas: New models, applications and realizations,” Scientific Reports, vol. 9, no. 1, p. 10178, 2019.DOI
  4. [4]D. R. Smith, O. Yurduseven, L. P. Mrstik, P. Bowen, and N. B. Kundtz, “Analysis of a waveguide-fed metasurface antenna,” Physical Review Applied, vol. 8, p. 054048, 2017.DOI
  5. [5]E. F. Kuester, M. A. Mohamed, M. Piket-May, and C. L. Holloway, “Averaged transition conditions for electromagnetic fields at a metafilm,” IEEE Transactions on Antennas and Propagation, vol. 51, no. 10, pp. 2641–2651, Oct. 2003.DOI
  6. [6]M. J. Mencagli, E. Martini, and S. Maci, “Surface wave dispersion for anisotropic metasurfaces constituted by elliptical patches,” IEEE Transactions on Antennas and Propagation, vol. 63, no. 7, pp. 2992–3003, Jul. 2015.
  7. [7]———, “Transition function for closed-form representation of metasurface reactance,” IEEE Transactions on Antennas and Propagation, vol. 64, no. 1, pp. 136–145, Jan. 2016.DOI
  8. [8]O. Luukkonen, C. Simovski, G. Granet, G. Gousssetis, D. Lioubtchenko, A. V. Räisänen, and S. A. Tretyakov, “Simple and accurate analytical model of planar grids and high-impedance surfaces comprising metal strips or patches,” IEEE Transactions on Antennas and Propagation, vol. 56, no. 6, pp. 1624–1632, Jun. 2008.
  9. [9]R. Rodríguez-Berral, F. Mesa, and F. Medina, “Analytical multimodal network approach for 2-D arrays of planar patches/apertures embedded in a layered medium,” IEEE Transactions on Antennas and Propagation, vol. 63, no. 5, pp. 1969–1984, May 2015.DOI
  10. [10]F. Mesa, M. García-Viguera, F. Medina, R. Rodríguez-Berral, and J. R. Mosig, “Circuit-model analysis of frequency selective surfaces with scatterers of arbitrary geometry,” IEEE Antennas and Wireless Propagation Letters, vol. 14, pp. 135–138, 2015.DOI
  11. [11]S. Maci, M. Caiazzo, A. Cucini, and M. Casaletti, “A pole-zero matching method for EBG surfaces composed of a dipole FSS printed on a grounded dielectric slab,” IEEE Transactions on Antennas and Propagation, vol. 53, no. 1, pp. 70–81, Jan. 2005.DOI
  12. [12]M. Bodehu, C. Craeye, and I. Huynen, “Electric field integral equation-based synthesis of elliptical-domain metasurface antennas,” IEEE Transactions on Antennas and Propagation, vol. 67, no. 2, pp. 1270–1274, Feb. 2019.
  13. [13]J. Meixner, “The behavior of electromagnetic fields at edges,” IEEE Transactions on Antennas and Propagation, vol. 20, no. 4, pp. 442–446, 1972.DOI
  14. [14]V. Galindo-Israel and R. Mittra, “A new series representation for the radiation integral with application to reflector antennas,” IEEE Transactions on Antennas and Propagation, vol. AP-25, no. 5, pp. 631–641, Sep. 1977.
  15. [15]K. Araki and T. Itoh, “Hankel transform domain analysis of open circular microstrip radiating structures,” IEEE Transactions on Antennas and Propagation, vol. 29, no. 1, pp. 84–89, Jan. 1981.DOI
  16. [16]W. C. Chew and J. A. Kong, “Effects of fringing field on the capacitance of a circular microstrip disk,” IEEE Transactions on Microwave Theory and Techniques, vol. 28, no. 2, pp. 98–104, Feb. 1980.DOI
  17. [17]K. A. Michalski and J. R. Mosig, “Multilayered media Green’s functions in integral equation formulations,” IEEE Transactions on Antennas and Propagation, vol. 45, no. 3, pp. 508–519, 1997.DOI
  18. [18]R. D. Gaglia, D. R. Wilton, and A. F. Peterson, “Higher order interpolatory vector bases for computational electromagnetics,” IEEE Transactions on Antennas and Propagation, vol. 45, no. 3, pp. 329–342, Mar. 1997.
  19. [19]J. Budhu, L. Szymanski, and A. Grbic, “Design of planar and conformal, passive, lossless metasurfaces that beamform,” IEEE Journal of Microwaves, vol. 2, no. 3, pp. 401–418, 2022.DOI
  20. [20]R. Pestourie, Y. Mroueh, C. Rackauckas, P. Das, and S. G. Johnson, “Physics-enhanced deep surrogates for partial differential equations,” Nature Machine Intelligence, vol. 5, no. 12, pp. 1458–1465, 2023.DOI
  21. [21]T. Fromenteze, “Analytical Modeling of the Admittance Tensor of Periodic Elliptical Meta-Atoms,” Zenodo, 2026. [Online]. Available: https://doi.org/10.5281/zenodo.23982840
  22. [22]S. Tretyakov, Analytical Modeling in Applied Electromagnetics. Norwood, MA: Artech House, 2003.
  23. [23]J. R. Mosig, “Arbitrarily shaped microstrip structures and their analysis with a mixed potential integral equation,” IEEE Transactions on Microwave Theory and Techniques, vol. 36, no. 2, pp. 314–323, Feb. 1988.DOI
  24. [24]R. Mittra, T. Itoh, and T.-S. Li, “Analytical and numerical studies of the relative convergence phenomenon arising in the solution of an integral equation by the moment method,” IEEE Transactions on Microwave Theory and Techniques, vol. 20, no. 2, pp. 96–104, 1972.DOI
  25. [25]A. M. Lerer and A. G. Schuchinsky, “Full-wave analysis of three-dimensional planar structures,” IEEE Transactions on Microwave Theory and Techniques, vol. 41, no. 11, pp. 2002–2015, 1993.DOI
  26. [26]G. Szegő, Orthogonal Polynomials, ser. Colloquium Publications. Providence, RI: American Mathematical Society, 1939, vol. 23.
  27. [27]L. D. Landau and E. M. Lifshitz, Electrodynamics of Continuous Media, 2nd ed. Oxford: Pergamon Press, 1984.
  28. [28]G. N. Watson, A Treatise on the Theory of Bessel Functions, 2nd ed. Cambridge, U.K.: Cambridge University Press, 1944.
  29. [29]Y. Rahmat-Samii, “Jacobi–Bessel analysis of reflector antennas with elliptical apertures,” IEEE Transactions on Antennas and Propagation, vol. 35, no. 9, pp. 1070–1074, Sep. 1987.
  30. [30]G. Vecchi, “Loop-star decomposition of basis functions in the discretization of the EFIE,” IEEE Transactions on Antennas and Propagation, vol. 47, no. 2, pp. 339–346, Feb. 1999.DOI
  31. [31]S. M. Rao, D. R. Wilton, and A. W. Glisson, “Electromagnetic scattering by surfaces of arbitrary shape,” IEEE Transactions on Antennas and Propagation, vol. 30, no. 3, pp. 409–418, May 1982.
  32. [32]S. D. Singh, W. F. Richards, J. R. Zinecker, and D. R. Wilton, “Accelerating the convergence of series representing the free space periodic Green’s function,” IEEE Transactions on Antennas and Propagation, vol. 38, no. 12, pp. 1958–1962, Dec. 1990.DOI
  33. [33]G. Valerio, P. Baccarelli, P. Burghignoli, and A. Galli, “Comparative analysis of acceleration techniques for 2-D and 3-D Green’s functions in periodic structures along one and two directions,” IEEE Transactions on Antennas and Propagation, vol. 55, no. 6, pp. 1630–1643, Jun. 2007.DOI
  34. [34]A. Hessel and A. A. Oliner, “A new theory of Wood’s anomalies in optical gratings,” Applied Optics, vol. 4, no. 10, pp. 1275–1297, 1965.DOI
  35. [35]A. M. Patel and A. Grbic, “Effective surface impedance of a printed-circuit tensor impedance surface (PCTIS),” IEEE Transactions on Microwave Theory and Techniques, vol. 61, no. 4, pp. 1403–1413, Apr. 2013.DOI
  36. [36]R. Erdélyi, W. Magnus, F. Oberhettinger, and F. G. Tricomi, Tables of Integral Transforms. New York, NY: McGraw-Hill, 1954, vol. II.

Paper details

vlnc:W_mys3au9s
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 8

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Claude

View statement
Looking for related papers…
Contents