betaFeedback

WorksPhysics and Astronomy

Role of the Nephelauxetic Effect in Engineering Mn4+ Luminescence Kinetics for Lifetime-Based Thermometry

Abstract

Although the considerable potential of luminescence thermometry based on emission kinetics has been widely demonstrated, reliable tools for the intentional prediction of thermometric performance remain limited. To address this challenge, the present work introduces an approach that enables a theoretical description of the 2E state lifetime of Mn4+ ions, as well as the absolute and relative sensitivities, in terms of the nephelauxetic effect within the group of double perovskites: Sr2InNbO6, Sr2InTaO6, Ba2InTaO6, and Ba2InNbO6. Our results clearly show that, contrary to common assumptions, the Dq/B ratio is not the primary factor governing either the spectroscopic behavior of Mn4+ ions or the thermometric performance of Mn4+-doped phosphors. Instead, the nephelauxetic beta1 parameter plays the dominant role. The empirical analysis carried out in this study led to the development of a predictive model that enables estimation of SAMAX and SRMAX values based exclusively on beta1. This methodology represents a significant step toward the rational design of lifetime-based luminescence thermometers with predefined thermometric characteristics tailored to the requirements of specific applications.

Introduction

The strong temperature dependence of luminescent properties in phosphor materials underpins the principle of luminescent thermometry, enabling remote, two-dimensional, and even three-dimensional thermal imaging [1, 2, 3, 4, 5, 6, 7]. Among the various spectroscopic parameters available for temperature readout, the luminescence intensity ratio (LIRLIR) and luminescence kinetics are the most widely employed because of their reliability and practical simplicity [8, 9, 10, 11, 12, 13, 14]. However, the shape of the emission spectrum and consequently the calculated LIRLIR can be significantly distorted by the optical characteristics of the medium between the thermometer and the detector, particularly in absorbing or scattering environments [13, 15]. Such distortions compromise the accuracy of temperature determination. In contrast, luminescence kinetics is inherently immune to these spectral distortions, making it an especially robust alternative. For lifetime-based thermometry, achieving high relative sensitivity typically requires a steep, thermally activated decrease in the luminescence lifetime. However, such steep changes often limit the thermal operating range of the thermometer. Conversely, applications that demand a broad thermal operating range benefit from a gradual, monotonic lifetime variation. Therefore, designing effective luminescent thermometers requires the ability to tailor their thermometric performance to meet the specific requirements of different applications.

In phosphors doped with lanthanide ions, the dominant process responsible for thermal depopulation of the emitting states is multiphonon relaxation[16, 17, 18, 19]. This process is governed by the phonon energy of the host lattice and the energy gap between the emitting level and the lower-lying states[20]. While the phonon energy of the host can be partially tuned via compositional modification, the energy levels of lanthanide ions, due to their shielded 4f4f orbitals, are only weakly perturbed by the crystal field environment[17, 21, 22]. Consequently, the energy separations between levels remain essentially constant across different host materials. An alternative strategy involves co-doping with additional ions to introduce energy transfer pathways that enhance thermal sensitivity[11, 12, 23, 24]. However, such approaches may introduce unwanted side effects, such as concentration quenching or spectral overlap[25, 26]. As a result, phosphors doped with lanthanide ions offer limited flexibility in tuning the thermometric performance of lifetime-based luminescence thermometers.

In contrast, phosphors doped with transition metal ions exhibit high sensitivity to both temperature changes and local crystal field variations[27, 28, 29, 30]. In such systems, even small changes in the crystal field strength and bonding covalence can induce substantial modifications in spectroscopic behavior [31, 32, 33, 34, 35, 36, 37]. A particularly illustrative example is the Mn4+\mathrm{Mn}^{4+} ion (3d33d^3 electronic configuration), for which the crystal field strength parameter Dq/BDq/B depends on the metal-oxygen bond length (RR) according to the approximate relationship Dq/B∼R−5Dq/B \sim R^{-5}[28, 38, 39]. Therefore, adjusting the chemical composition of the host material, and thereby modifying RR, directly affects the thermal activation energy that governs the temperature-dependent luminescence decay from the 2E^{2}\mathrm{E} state[27, 40]. This provides a route to broadly tune the thermometric behavior of Mn4+\mathrm{Mn}^{4+}-based thermometers. Nevertheless, Dq/BDq/B is not the only factor influencing the thermal evolution of Mn4+\mathrm{Mn}^{4+} luminescence kinetics. For this reason, the rational design of application-specific luminescent thermometers requires systematic investigation of the correlations between structural parameters and chemical composition of the host lattice and the spectroscopic behavior of Mn4+\mathrm{Mn}^{4+}-doped phosphors.

To address this issue, the present work systematically examines the luminescence of Mn4+\mathrm{Mn}^{4+} ions in four different double perovskite hosts, Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6}, Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}, Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}, and Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}. By systematically varying both the A-site and B'-site cations, we aim to establish structure-luminescent property correlations that govern the relative sensitivity and overall thermometric performance of these Mn4+\mathrm{Mn}^{4+}-doped phosphors.

Experimental

Synthesis

Polycrystalline powders of Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6}:1%Mn4+\mathrm{Mn}^{4+}, Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}:1%Mn4+\mathrm{Mn}^{4+}, Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}:1%Mn4+\mathrm{Mn}^{4+}, and Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}:1%Mn4+\mathrm{Mn}^{4+} were synthesized via high temperature solid-state reaction route. Strontium(II) carbonate SrCO3\mathrm{SrCO}_{3}, indium(III) oxide In2O3\mathrm{In}_{2}\mathrm{O}_{3}, tantalum(V) oxide Ta2O5\mathrm{Ta}_{2}\mathrm{O}_{5}, niobium(V) Oxide Nb2O5\mathrm{Nb}_{2}\mathrm{O}_{5}, barium(II) carbonate BaCO3\mathrm{BaCO}_{3}, manganese(II) chloride tetrahydrate MnCl2⋅4H2O\mathrm{MnCl}_{2}\cdot4\mathrm{H}_{2}\mathrm{O} were weighed stoichiometrically and thoroughly ground in an agate mortar in hexane medium. Then, the resulting mixtures were transferred to crucibles separately and were initially calcined for 6 h at 600 °C in a muffle furnace. After calcination, the precursor was reground and then subject to further calcination at 1300 °C for 6h.

Characterization

The obtained materials were examined by X-ray powder diffraction (XRD) using a PANalytical X'Pert Pro diffractometer in Bragg-Brentano geometry, using Ni-filtered Cu Kα\mathrm{K}\alpha radiation (V=40V = 40 kV, I=30I = 30 mA). Measurements were made in the range of 10-90°, and the acquisition time was approximately 30 min. The samples were also investigated using a scanning electron microscopy (SEM, FEI Nova NanoSEM 230) equipped with an energy-dispersive X-ray spectrometer (EDX, EDAX Apollo X Silicon Drift Correction) compatible with genesis EDAX microanalysis Software. The samples were dispersed in alcohol, and a drop of the suspension was placed onto a carbon stub. SEM images were then collected using an accelerating voltage of 5.0 kV, while EDS measurements were performed at a higher accelerating voltage of 30 kV.

Raman spectra were collected using an Edinburgh Instruments RMS-1000 Raman microscope equipped with a 532 nm excitation laser, a 20x microscope objective, and an 1800 lines mm−1\mathrm{mm}^{-1} diffraction grating. Temperature stabilization during the measurements was ensured using a temperature-control THMS600 stage from Linkam.

Excitation and emission spectra were measured using an FLS1000 spectrometer from Edinburgh Instruments, equipped with a 450 W xenon lamp as the excitation source, and an R928P side window photomultiplier tube from Hamamatsu as a detector. The luminescence decay curves were recorded on this spectrometer with a pulsed excitation, provided by a μ\muFlash lamp. Temperature of the samples during the measurements was controlled using THMS600 heating-cooling stage from Linkam.

The luminescence decay profiles were fitted with a double exponential function, as expressed below:

I(t)=I0+A1⋅exp⁡(−tτ1)+A2⋅exp⁡(−tτ2)(1)I(t) = I_0 + A_1 \cdot\exp\left(-\frac{t}{\tau_1}\right) + A_2 \cdot\exp\left(-\frac{t}{\tau_2}\right) \tag*{(1)}

where I(t)I(t), A1A_1, A2A_2, I0I_0, τ1\tau_1, and τ2\tau_2, represent the luminescence intensity at time tt right after laser pulse excitation, preexponential factors, offset, and decay parameters, respectively. Based on these parameters the average lifetime τavr\tau_{avr} were calculated as follows:

τavr=A1τ12+A2τ22A1τ1+A2τ2(2)\tau_{avr}=\frac{A_1\tau_1^2+A_2\tau_2^2}{A_1\tau_1+A_2\tau_2} \tag*{(2)}

Results and discussion

The structure of the A2BB′O6A_2BB^{\prime}O_6 double perovskites is derived from the simple perovskite through the ordered arrangement of the BB and B′B^{\prime} cations in alternating octahedral sites[31, 41, 42, 43, 44, 45]. In this structure, the AA site is usually occupied by the larger cations - Sr2+\mathrm{Sr}^{2+} or Ba2+\mathrm{Ba}^{2+}. Each Sr2+\mathrm{Sr}^{2+} ion is surrounded by eight oxygen atoms, whereas each Ba2+\mathrm{Ba}^{2+} ion is coordinated by twelve oxygen atoms (Figure 1a, Figure 1b)[46, 47, 48, 49, 50, 51]. On the other hand, the BB site is occupied by In3+\mathrm{In}^{3+} ions, and B′B^{\prime} by Ta5+\mathrm{Ta}^{5+} or Nb5+\mathrm{Nb}^{5+}, respectively, each exhibiting octahedral coordination[52, 53, 54, 55, 56, 57]. A comparison of the structural parameters of the host materials examined in this study presented in Table 1 indicates that Sr2InNbO6:Mn4+\mathrm{Sr}_2\mathrm{InNbO}_6:\mathrm{Mn}^{4+} and Sr2InTaO6:Mn4+\mathrm{Sr}_2\mathrm{InTaO}_6:\mathrm{Mn}^{4+} crystallize in a monoclinic structure with a P21/nP2_1/n space group, whereas Ba2InTaO6:Mn4+\mathrm{Ba}_2\mathrm{InTaO}_6:\mathrm{Mn}^{4+} and Ba2InNbO6:Mn4+\mathrm{Ba}_2\mathrm{InNbO}_6:\mathrm{Mn}^{4+} compositions adopt the cubic structure with Fm3ˉmFm\bar{3}m space group[52, 53, 54, 55]. The symmetry of these host structures was confirmed by calculating the Goldschmidt geometric tolerance factor tt, which for double perovskites is defined as follows[58]:

Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6}Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}
Crystal structuremonoclinicmonocliniccubiccubic
Space groupP21/nP2_{1}/n (14)P21/nP2_{1}/n (14)Fm3‾mFm\overline{3}m (225)Fm3‾mFm\overline{3}m (225)
Cell parameter (Å)a=5.7351(2)a = 5.7351(2)<br>b=5.7416(2)b = 5.7416(2)<br>c=8.1102(3)c = 8.1102(3)a=5.73356(10)a = 5.73356(10)<br>b=5.74052(10)b = 5.74052(10)<br>c=8.10905(14)c = 8.10905(14)a=8.29640(1)a = 8.29640(1)a=8.2819(2)a = 8.2819(2)
Cell volume (Å3^{3})267.058266.898571.043568.054
Average bond length<br>(Ta5+/Nb5+\mathrm{Ta}^{5+}/\mathrm{Nb}^{5+}-O2−\mathrm{O}^{2-}) (Å)2.0032.01062.0162.0705

Table 1. Comparison of structural parameters of Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6}, Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}, Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6} and Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6} host materials.

Graphical representation of double-perovskite structures, diffraction patterns, Raman spectra, and SEM images

Figure 1. Graphical representation of the cubic structure of Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6} - a) and monoclinic structure of Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6} - b); comparison of room temperature X-ray diffraction patterns of Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}, Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}, Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6}, and Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6} doped with 1% Mn4+\mathrm{Mn}^{4+} ions with reference patterns - c); room temperature Raman spectra of the analyzed compounds – d); representative SEM images of Sr2InTaO6 ⁣:Mn4+\mathrm{Sr}_{2}\mathrm{InTaO}_{6}\!:\mathrm{Mn}^{4+}– e), Sr2InNbO6 ⁣:Mn4+\mathrm{Sr}_{2}\mathrm{InNbO}_{6}\!:\mathrm{Mn}^{4+}- f), Ba2InTaO6 ⁣:Mn4+\mathrm{Ba}_{2}\mathrm{InTaO}_{6}\!:\mathrm{Mn}^{4+}- g), Ba2InNbO6 ⁣:Mn4+\mathrm{Ba}_{2}\mathrm{InNbO}_{6}\!:\mathrm{Mn}^{4+}- h).

t=[rA+rO2(rB+rB′2+rO)](3)t=\left[\frac{r_A+r_O}{\sqrt{2}\left(\frac{r_B+r_{B^{\prime}}}{2}+r_O\right)}\right] \tag*{(3)}

where rAr_A is the ionic radii of the AA cation, rBr_B and rB′r_{B^{\prime}} are the ionic radii of BB and B′B^{\prime} ions in six-fold coordination and rOr_O is the ionic radii of the oxygen ion (1.40 Å). The value of tt reflects the stability of the perovskite structure. The highest stability occurs for t=1t=1, which corresponds to with the ideal cubic perovskite structure. According to literature, when tt exceeds 0.98, the material typically adopts a cubic Fm3‾mFm\overline{3}m (a0a_0, a0a_0, a0a_0) structure, whereas for tt values between 0.96 and 0.98, rhombohedral or tetragonal symmetries are most commonly reported[47, 49, 52, 53, 59, 60, 61]. The tolerance factor for the Ba2In(Ta,Nb)O6\mathrm{Ba}_2\mathrm{In}(\mathrm{Ta},\mathrm{Nb})\mathrm{O}_6 compositions is close to 1 (Table 1), consistent with their adoption of a cubic structure. It implies linear In3+\mathrm{In}^{3+}-O2−\mathrm{O}^{2-}-(Ta,Nb)5+^{5+} bonds (180∘180^\circ) and the ideal (NbO6)7−(\mathrm{NbO}_6)^{7-} and (TaO6)7−(\mathrm{TaO}_6)^{7-} octahedra. The larger Ba2+\mathrm{Ba}^{2+} ions are in a twelve-fold coordination in this double perovskite. In contrast, replacing Ba2+\mathrm{Ba}^{2+} with the smaller Sr2+\mathrm{Sr}^{2+} ion introduces a size mismatch between the AA-site cation and the cuboctahedral cavity formed by the twelve surrounding oxide ions. This mismatch drives octahedral tilting, lowering the symmetry. With a calculated tolerance factor of t=0.88t = 0.88, the Sr2In(Ta,Nb)O6\mathrm{Sr}_2\mathrm{In}(\mathrm{Ta},\mathrm{Nb})\mathrm{O}_6 analogs are predicted to adopt a monoclinic structure, in agreement with X-ray diffraction results (Figure 1b). In these Sr2+\mathrm{Sr}^{2+}-based compounds, Sr2+\mathrm{Sr}^{2+} is eight-fold coordinated, and the In3+\mathrm{In}^{3+}-O2−\mathrm{O}^{2-}-(Ta,Nb)5+^{5+} bond angle decreases to approximately 169∘169^\circ, reflecting the octahedral tilting[46, 47, 48, 49, 52, 57].

Interpreting the optical data requires identifying the specific host-lattice site occupied by Mn4+\mathrm{Mn}^{4+}. In these double perovskite structures, two distinct octahedral sites are available for substitution by Mn4+\mathrm{Mn}^{4+} ions. Although one might argue that the coupled substitution 2Mn4+→In3++Nb5+/Ta5+2\mathrm{Mn}^{4+}\rightarrow\mathrm{In}^{3+}+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+} is favourable from a charge-balance perspective, the ionic-radius mismatch strongly disfavours this mechanism, as discussed below. The suitability of this substitution can be assessed by calculating the radius percentage difference DRD_R between Mn4+\mathrm{Mn}^{4+} and host-cation (Nb5+/Ta5+,In3+)(\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+}, \mathrm{In}^{3+}) using the following formula[62]:

DR=Rm(CN)−Rd(CN)Rm(CN)×100%(4)D_R = \frac{R_m(CN)-R_d(CN)}{R_m(CN)} \times100\% \tag*{(4)}

where Rm(CN)R_m(CN) and Rd(CN)R_d(CN) are the ionic radii of the host and dopant cation, respectively. The ionic radii of the ions in sixfold coordination considered in this case are as follows: Mn4+\mathrm{Mn}^{4+} (0.53 Å), In3+\mathrm{In}^{3+} (0.80 Å), Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+} (0.64 Å)[63]. Because favourable substitution typically requires the DRD_R value to be below 30%, the calculated DRD_R values of 33.75% for Mn4+\mathrm{Mn}^{4+} substituting In3+\mathrm{In}^{3+} and 17.2% substituting Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+} indicate a clear preference for incorporation at the Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+} sites. Substitutions at these sites minimize local elastic strain effects or lattice distortions. However, the substitution of Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+} by Mn4+\mathrm{Mn}^{4+} ions, which differ in charge, is expected to disrupt local charge neutrality generating positively charged defects such as oxygen vacancies or anti-site disorder to restore balance[48, 52]. This disruption not only affects the charge distribution but can also influence the crystal structure[64, 65, 66]. Furthermore, this structural distortion is consistent with reports of around 10% anti-site disorder, where In3+\mathrm{In}^{3+} and Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+} exchange positions within the rock salt type structure, indicative of translational stacking faults[57] [67].

In the fully ordered structure of the A2BB′O6A_{2}BB'\mathrm{O}_{6} double perovskite oxides, each BB cation has only B′B' as the next nearest neighbour and vice versa. However, this ordering is never complete and some degree of mixing between the BB and B′B' cations occur. The degree of order is determined by the difference between the ionic size and charge of the BB-site cations[68, 69, 70]. The degree of mixing increases with smaller ionic radii and charge differences between the two BB-site cations.

According to Woodward et al. when the ionic-radius difference is Δr≤0.260\Delta r \le0.260 Å, complete (100%) B/B′B/B' ordering is generally not observed[71, 72, 73]. Further, when the AA-site cation is smaller and the crystal symmetry is reduced, the same B/B′B/B' combination tends to show higher ordering levels. For example, Sr2ScNbO6\mathrm{Sr_2ScNbO_6} and Ca2ScNbO6\mathrm{Ca_2ScNbO_6}, both adopting the monoclinic structure, exhibit ordering levels of 69% and 96%[74].

Applying these insights to the present compositions, the ionic radius difference between In3+\mathrm{In^{3+}} and Nb5+/Ta5+\mathrm{Nb^{5+}/Ta^{5+}} is Δr=0.16\Delta r = 0.16 Å, a value that suggests a substantial degree of B/BB/B disorder. This mixing is expected to be more pronounced in the cubic Ba2In(Ta,Nb)O6\mathrm{Ba_2In(Ta,Nb)O_6} phases than in the monoclinic Sr2In(Ta,Nb)O6\mathrm{Sr_2In(Ta,Nb)O_6} analogs, where lower symmetry typically favours higher ordering. A long-range order of 80% and 86% has been reported for Sr2InNbO6\mathrm{Sr_2InNbO_6} and Sr2InTaO6\mathrm{Sr_2InTaO_6}, respectively[48, 52]. Such considerations are essential when interpreting the spectroscopic features and luminescence lifetimes of Mn4+\mathrm{Mn^{4+}} in these double-perovskite hosts and would be important when discussing the spectroscopic and the lifetime data of the Mn4+\mathrm{Mn^{4+}} in these double perovskites in the later part of this work.

X-ray diffraction patterns of Sr2InTaO6:Mn4+\mathrm{Sr_2InTaO_6:Mn^{4+}}, Ba2InTaO6:Mn4+\mathrm{Ba_2InTaO_6:Mn^{4+}}, Sr2InNbO6:Mn4+\mathrm{Sr_2InNbO_6:Mn^{4+}} and Ba2InNbO6:Mn4+\mathrm{Ba_2InNbO_6: Mn^{4+}}, presented in Figure 1c, correlate well with the standard reference data. No traces of the residual or impurities were detected, indicating successful incorporation of Mn4+\mathrm{Mn^{4+}} into the host materials. The replacement of Nb5+/Ta5+\mathrm{Nb^{5+}/Ta^{5+}} (R=0.64R=0.64 Å) by smaller Mn4+\mathrm{Mn^{4+}} ions (R=0.53R=0.53 Å) is expected to cause lattice contraction, which should result in a shift of the reflections toward higher angles. However, this shift is not clearly observed in the investigated case, most likely due to the low concentration of Mn4+\mathrm{Mn^{4+}} ions.

Room-temperature Raman spectra were collected for all compounds to probe their structural symmetry and vibrational properties (Figure 1d). The recorded spectra clearly reveal the presence of two distinct structural groups. The Ba2+\mathrm{Ba^{2+}}-based compounds exhibit Raman spectra with 14 active modes, consistent with a cubic crystal structure[57]. In contrast, the Sr2+\mathrm{Sr}^{2+}-based compounds exhibit a much larger number of Raman-active modes, indicative of the lower-symmetry monoclinic structure. For the Sr2+\mathrm{Sr}^{2+}-based compounds, the most intense Raman bands appear near 800, 560, 420 cm−1\mathrm{cm}^{-1}, along with additional modes below 300 cm−1\mathrm{cm}^{-1}. In contrast, the Ba2+\mathrm{Ba}^{2+}-based analogs are characterized by dominant low-frequency band around 100 cm−1\mathrm{cm}^{-1}, and pronounced features near 400 cm−1\mathrm{cm}^{-1}. The mode near 800 cm−1\mathrm{cm}^{-1} is assigned to the symmetric stretching vibrations of the (TaO6)7−/(NbO6)7−(\mathrm{TaO}_{6})^{7-}/(\mathrm{NbO}_{6})^{7-} octahedra. Bands in the 500-600 cm−1\mathrm{cm}^{-1} region arise from Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+}-O2−\mathrm{O}^{2-} stretching modes, including antisymmetric stretching vibrations. Vibrations observed between 300 and 450 cm−1\mathrm{cm}^{-1} correspond to O2−\mathrm{O}^{2-}-Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+}-O2−\mathrm{O}^{2-} bending modes. At lower wavenumbers (<300 cm−1\mathrm{cm}^{-1}), the spectra are dominated by lattice translational and vibrational modes [57, 75, 76] [67]. A comparative analysis of the Raman spectra reveals systematic differences arising from substitutions at both the AA and BB cation sites in these double perovskites. For compounds containing the same B′B^\prime cation, the Ba2+\mathrm{Ba}^{2+}-based members consistently exhibit Raman bands shifted to lower wavenumbers most notably the mode near 400 cm−1\mathrm{cm}^{-1}. This shift reflects the larger ionic radius of Ba2+\mathrm{Ba}^{2+} relative to Sr2+\mathrm{Sr}^{2+}, which weakens AA-OO interactions, reduces bond stiffness, and lowers the corresponding vibrational frequencies. In contrast, the smaller Sr2+\mathrm{Sr}^{2+} ion strengthens the ionic character of the Sr2+\mathrm{Sr}^{2+}-O2−\mathrm{O}^{2-} bonds and contracts the lattice, producing a systematic shift of Raman modes toward higher wavenumbers.

Substitution at the B′B^\prime site (Ta5+→Nb5+\mathrm{Ta}^{5+}\rightarrow\mathrm{Nb}^{5+}) produces more subtle changes in the Raman spectra. Because Ta5+\mathrm{Ta}^{5+} and Nb5+\mathrm{Nb}^{5+} possess identical ionic radii and the same charge, the overall crystal symmetry remains essentially unchanged. The subtle variations observed in the spectra therefore arise mainly from differences in Ta5+\mathrm{Ta}^{5+}-O2−\mathrm{O}^{2-} versus Nb5+\mathrm{Nb}^{5+}-O2−\mathrm{O}^{2-} bond strengths, which produce slight shifts in the positions and relative intensities of the octahedral stretching and bending modes. The analysis of the SEM images for the analyzed phosphors revealed that they consist of microcrystalline and aggregated crystals (Figure 1 e-Figure 1h).

The overall optical behaviour of the Mn4+\mathrm{Mn}^{4+} center can be interpreted using the schematic configurational-coordinate diagram shown in Figure 2a. Because Mn4+\mathrm{Mn}^{4+} ions experiences a strong octahedral crystal field arising from its high effective charge, its luminescence is characteristically dominated by sharp-line emission from the spin-forbidden 2Eg→4A2g{}^{2}\mathrm{E}_{g}\to{}^{4}\mathrm{A}_{2g} transition (Figure 2b, Figure 2c). The low temperature (T=83T=83 K) excitation spectra of the Mn4+\mathrm{Mn}^{4+}-doped double perovskites presented in Figure 2d reveal the presence of four major bands: the host lattice absorption (HL), the O2−→Mn4+\mathrm{O}^{2-}\to\mathrm{Mn}^{4+} charge transfer transition (CT), and the spin-allowed but parity-forbidden 4A2→4T1{}^{4}\mathrm{A}_{2}\to{}^{4}\mathrm{T}_{1} and 4A2→4T2{}^{4}\mathrm{A}_{2}\to{}^{4}\mathrm{T}_{2} transitions (Table 2). Based on these values the crystal field parameters can be determined. The energy separation between the 4A2{}^{4}\mathrm{A}_{2} ground and 4T2{}^{4}\mathrm{T}_{2} excited states defines the octahedral crystal field strength, Δo=10Dq\Delta_{\mathrm{o}} = 10Dq. The crystal field parameter DqDq is obtained by the formula: E(4A2→4T2)/10=DqE({}^{4}\mathrm{A}_{2}\to{}^{4}\mathrm{T}_{2})/10 = Dq, where E(4A2→4T2)E({}^{4}\mathrm{A}_{2}\to{}^{4}\mathrm{T}_{2}) is the peak energy of the optical transition. As discussed earlier, the point charge model predicts DqDq to vary as R−5R^{-5}, with RR representing the Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond distance[77]. Analysis of the recorded spectra reveals that substitutions at both the AA and B′B' sites affect the energy of the Mn4+\mathrm{Mn}^{4+} levels. Replacement of Ba2+\mathrm{Ba}^{2+} with Sr2+\mathrm{Sr}^{2+} at the AA site induces a pronounced blueshift of the 4A2→4T1{}^{4}\mathrm{A}_{2}\to{}^{4}\mathrm{T}_{1} band, corresponding to energy differences of 1771 cm−1^{-1} for the Nb5+\mathrm{Nb}^{5+}-based hosts and 1888 cm−1^{-1} for the Ta5+\mathrm{Ta}^{5+}-based analogues. Consistent with their shorter (Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+})-O2−\mathrm{O}^{2-} bond lengths (Table 1), the Sr2+\mathrm{Sr}^{2+}-based analogs exhibit larger DqDq values. In contrast, substitution at the B′B' site (Nb5+→Ta5+\mathrm{Nb}^{5+}\to\mathrm{Ta}^{5+}) results in considerably smaller spectral changes, manifested by a slight redshift of approximately 120 cm−1^{-1} in the Sr2+\mathrm{Sr}^{2+}-based compounds, while having a negligible effect on the Ba2+\mathrm{Ba}^{2+}-based materials.

hostHL (cm−1^{-1})CT (cm−1^{-1})4A2→4T1{}^{4}\mathrm{A}_{2}\to{}^{4}\mathrm{T}_{1} (cm−1^{-1})4A2→4T2{}^{4}\mathrm{A}_{2}\to{}^{4}\mathrm{T}_{2} (cm−1^{-1})DqDq (cm−1^{-1})(Nb5+/Ta5+\mathrm{Nb}^{5+}/\mathrm{Ta}^{5+})-O2−\mathrm{O}^{2-} (Å)
Sr2_{2}InTaO6_{6}30 14826 34618 01818022.0106
Sr2_{2}InNbO6_{6}29 73626 22717 96717962.003
Ba2_{2}InTaO6_{6}29 46924 45816 54716552.016
Ba2_{2}InNbO6_{6}28 94324 45616 72816732.0705

Table 2. Energies of the Mn4+\mathrm{Mn}^{4+} transitions and DqDq determined based on the excitation spectra measured at 83 K for the analyzed host materials.

Simplified configurational-coordination diagram, emission and excitation spectra, maps, luminescence decay profiles, and parameter comparisons

Figure 2. Simplified configurational-coordination diagram of Mn4+\mathrm{Mn}^{4+} ions – a); the comparison of normalized emission spectra of analyzed phosphors measured at 83 K – b); and corresponding maps – c); comparison of excitation spectra of analyzed phosphors measured at 83 K – d); and luminescence decay profiles – e); the values of BB – f), Dq/BDq/B – g), β1\beta_{1} – h) and τavr\tau_{\mathrm{avr}} – i) for the analyzed phosphors.

The emission spectra recorded at 83 K consists of the zero-phonon line (RR-line) along with the Stokes and anti-Stokes vibronic bands (Figure 2b, Figure 2c). Comparison of emission spectra reveals that substituting the AA- and B′B'-site cations induces modifications to the crystal-field environment surrounding the Mn4+\mathrm{Mn}^{4+} ions, manifested by differences in optical response (Figure 2c). To further analyze the optical data, the values of the Racah parameters BB and CC were calculated from the experimental excitation and emission spectra using the following relationships (Table 3)[28, 33]:

B=(ΔETDq)2−10(ΔETDq)15(ΔETDq−8)Dq(5)B=\frac{\left(\frac{\Delta E_T}{Dq}\right)^2-10\left(\frac{\Delta E_T}{Dq}\right)}{15\left(\frac{\Delta E_T}{Dq}-8\right)}Dq \tag*{(5)}
ΔET=E(4T1g)−E(4T2g)(6)\Delta E_T=E\left({}^{4}T_{1g}\right)-E\left({}^{4}T_{2g}\right) \tag*{(6)}
C=0.328ΔEE−2.59B+0.59B2Dq(7)C=0.328\Delta E_E-2.59B+0.59\frac{B^2}{Dq} \tag*{(7)}
ΔEE=E(2Eg)(8)\Delta E_E=E\left({}^{2}E_g\right) \tag*{(8)}

The nephelauxetic β1\beta_1 parameter was calculated using the following equation[78]:

β1=(BB0)2+(CC0)2(9)\beta_1=\sqrt{\left(\frac{B}{B_0}\right)^2+\left(\frac{C}{C_0}\right)^2} \tag*{(9)}

where B0B_0 and C0C_0 represent the Racah parameters for Mn4+\mathrm{Mn}^{4+} ion in free state (B0=1160 cm−1B_0=1160\ \mathrm{cm}^{-1}, C0=4303 cm−1C_0=4303\ \mathrm{cm}^{-1})[78].

hostBB (cm−1^{-1})CC (cm−1^{-1})2E{}^{2}E (cm−1^{-1})β1\beta_1RiRi = ZPL/ν6\nu_6τav\tau_{av} (ms)
Sr2_2InTaO6_6890280614 7771.007∼\sim0.420.181
Sr2_2InNbO6_6875283914 7761.002∼\sim0.430.164

Table 3. The Racah parameters and spectroscopic parameters of Mn4+\mathrm{Mn}^{4+} ions in the analyzed host materials.

Ba2_2InTaO6_6855276214 3640.977∼\sim0.480.033
Ba2_2InNbO6_6820281514 3200.963∼\sim0.710.014

Table 3 (PDF p. 14).

As can be observed from the data assembled in Table 3, the energy of the 2E^{2}\mathrm{E} state is lowered by about 430 cm−1^{-1} when moving from Sr2_2In(Ta/Nb)O6_6:Mn4+^{4+} to Ba2_2In(Ta/Nb)O6_6:Mn4+^{4+}. The value of the β1\beta_1 parameter is also lower in the Ba2+^{2+}-phases relative to their Sr2+^{2+}-counterparts. As discussed earlier, the energy of the 2E^{2}\mathrm{E} state depends on the Mn4+^{4+}-O2−^{2-} bonding covalence. Further, higher the covalence, lower is the value of the β1\beta_1 parameter. This shows that the covalent bonding is much stronger in the perovskite framework of the Ba2+^{2+}-phases than their Sr2+^{2+}-counterparts. The difference in covalency between the Ba2+^{2+}- and Sr2+^{2+}-based perovskite frameworks can be rationalized by considering the geometry of their octahedral units. In an ideal octahedron, all six Mn4+^{4+}-O2−^{2-} bonds are equivalent, and the 15 characteristic angles consist of three linear (180°) and twelve right angles (90°). Distortions in a perovskite octahedron arise either from unequal Mn4+^{4+}-O2−^{2-} bond lengths or from deviations of the octahedral angles from the ideal 90° value. In the Ba2+^{2+} phases, the octahedra remain essentially ideal. This highly symmetric environment enhances Mn4+^{4+} t2g_{2g}-O2−^{2-} pπ_\pi orbital overlap, leading to increased Mn4+^{4+}-O2−^{2-} covalency even though the bond distances are longer. In contrast, the Sr2+^{2+} phases exhibit significant octahedral distortion and tilting, with In3+^{3+}-O2−^{2-}-(Ta,Nb)5+^{5+} angles reduced to ∼\sim169°, producing a distorted framework. The deviation from ideal symmetry diminishes the Mn4+^{4+} t2g_{2g}-O2−^{2-} pπ_\pi orbital overlap and consequently lowers the covalency of the Mn4+^{4+}-O2−^{2-} bond.

It is noteworthy that β1\beta_1 and the energies of the 2E^{2}\mathrm{E}-state in Sr2_2InNbO6_6:Mn4+^{4+} and Sr2_2InTaO6_6:Mn4+^{4+} are very similar. Given the Pauling electronegativities of Nb5+^{5+} (1.6) and Ta5+^{5+} (1.5), one would normally expect the (InNbO6_6) framework to be slightly more covalent than (InTaO6_6). This expectation is supported by the lower-energy O2−^{2-}→Mn4+^{4+} charge-transfer band observed in Ba2_2InNbO6_6 (29 736 cm−1^{-1}) compared with its value of 30 148 cm−1^{-1} in Sr2_2InTaO6_6.

Nevertheless, both the 2E^{2}\mathrm{E}-state energy and the covalence parameter β1\beta_{1} remain nearly identical in these two Sr2+\mathrm{Sr}^{2+}-based double perovskites. In contrast, the Ba2+\mathrm{Ba}^{2+} analogues display a clearer trend: the (InNbO6)(\mathrm{InNbO}_{6}) framework is indeed more covalent than its Ta5+\mathrm{Ta}^{5+}-containing counterpart, consistent with the electronegativity difference. This is further evidenced by the lower-energy of O2−→Mn4+\mathrm{O}^{2-}\to\mathrm{Mn}^{4+} charge-transfer band in Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6} (28 943 cm−1^{-1}) relative to Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6} (29 469 cm−1^{-1}). Among all compositions examined, Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}:Mn4+\mathrm{Mn}^{4+} exhibits the highest Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond covalency. The compositional dependence of the Racah parameter BB and the Dq/BDq/B and β1\beta_{1} parameter are visualized in Figure 2f, 2g and 2h, respectively. The analysis of the presented data reveals that the Dq/BDq/B values follow the trend, Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}:Mn4+\mathrm{Mn}^{4+} (Dq/B=1.93Dq/B=1.93) < Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}:Mn4+\mathrm{Mn}^{4+} (Dq/B=2.02Dq/B=2.02) < Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}:Mn4+\mathrm{Mn}^{4+} (Dq/B=2.04Dq/B=2.04) < Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6}:Mn4+\mathrm{Mn}^{4+} (Dq/B=2.05Dq/B=2.05). With the exception of Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}, Dq/BDq/B decreases with increasing Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} distances, consistent with the Tanabe-Sugano diagram. We note that the deviation observed for Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}, which has the longest Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond distances among all hosts considered, may arise from its markedly higher covalency. This compound exhibits the smallest BB and β1\beta_{1} value of any composition in this study.

The comparison of luminescence decay profile of Mn4+\mathrm{Mn}^{4+} in Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}, Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6}, Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6} and Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}, measured at 83 K shown in Figure 2e reveals that the Ba2+\mathrm{Ba}^{2+}-based compounds exhibit noticeably shorter τavr\tau_{avr} values than their Sr2+\mathrm{Sr}^{2+}-based analogs, indicating that τavr\tau_{avr} is strongly dependent on the host lattice. In general, several structural and electronic factors can influence the decay kinetics of Mn4+\mathrm{Mn}^{4+} ions, and these aspects are discussed in detail later in this work. Table 4 summarizes the peak intensity ratio of the RR-line to its most intense Stokes ν6\nu_{6} sideband (RiR_i). A striking aspect of these data is the unusually high RR-line intensity observed for Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6} (∼0.71\sim0.71), which is markedly greater than that of the Ta5+\mathrm{Ta}^{5+}-analog (∼0.45\sim0.45). The substituted B′B' site (Ta5+/Nb5+\mathrm{Ta}^{5+}/\mathrm{Nb}^{5+}) possesses inversion symmetry not only with respect to the nearest-neighbour oxygen coordination but also relative to the next-nearest-neighbour cations. Consequently, no static odd-parity distortions are present, and the RR-line is a magnetic-dipole transition with low oscillator strength. In contrast, the vibronic sidebands, activated by odd-parity lattice vibrations, are electric-dipole allowed and therefore expected to dominate the spectrum. Under such centrosymmetric coordination, the ZPL/ν6\nu_{6} ratio should remain small. Yet, in Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}, the RR-line exhibits a surprisingly large gain in intensity, deviating from this expectation.

As previously shown in these double perovskites, BB-site cation mixing removes the inversion symmetry at the Mn4+\mathrm{Mn}^{4+} center with respect to the next-nearest-neighbour cations. This symmetry breaking relaxes the parity selection rule and leads to an increase in the RiR_i value. In Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}, the degree of interchange among the BB-site cations is estimated to be about 25% [56] [67]. However, this mechanism cannot account for the difference in RiR_i observed between Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6} and Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}, because the extent of BB-site mixing, which is driven primarily by the ionic-radius and charge differences between the BB-site cations, is the same in both compositions. Therefore, this difference can be attributed to the greater covalency of Ba2InNbO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6} relative to Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6}. The enhanced covalence in the Nb5+\mathrm{Nb}^{5+}-analog arises from the stronger hybridization between the Nb5+ t2g\mathrm{Nb}^{5+}\ t_{2g} orbitals and the O2− 2pπ\mathrm{O}^{2-}\ 2p_{\pi} orbitals. Although both Nb5+ (4d0)\mathrm{Nb}^{5+}\ (4d^{0}) and Ta5+ (5d0)\mathrm{Ta}^{5+}\ (5d^{0}) possess empty orbitals capable of forming covalent interactions with the oxide 2p2p orbitals, the Nb5+\mathrm{Nb}^{5+}-O2−\mathrm{O}^{2-} hybridization is more effective. In addition, contributions from the In3+ 5s\mathrm{In}^{3+}\ 5s orbitals also play a non-negligible role in strengthening the overall covalent interaction. The RiR_i value does not change between Sr2InNbO6\mathrm{Sr}_{2}\mathrm{InNbO}_{6} and Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6} due to the fact that in these compositions the bonding covalence within the perovskite framework is the same as evidenced by the similar energy of the 2E{}^{2}E state and the value of the β1\beta_{1} parameter. In Sr2InTaO6\mathrm{Sr}_{2}\mathrm{InTaO}_{6}, the degree of interchange among the BB-site cations is estimated to be about 10%, which is less than that observed in the corresponding Ba2+\mathrm{Ba}^{2+}-analog[47] [67]. This is expected based on the Woodward observation that the mixing between the BB-site cations decreases with decreasing ionic radii of the AA cation and lowering of the symmetry. The lower covalence of the perovskite framework in the Sr2+\mathrm{Sr}^{2+}-phases and the smaller degree of BB-site mixing is responsible for the much smaller RiRi in the Sr2+\mathrm{Sr}^{2+}-phases relative to the Ba2+\mathrm{Ba}^{2+}-based counterparts.

To evaluate how crystal structure and chemical composition of the phosphor influence the thermal stability of Mn4+\mathrm{Mn}^{4+} luminescence in the investigated double perovskites, temperature-dependent emission spectra were recorded. A representative set of emission spectra as a function of temperature for Ba2InNbO6:Mn4+\mathrm{Ba}_{2}\mathrm{InNbO}_{6}:\mathrm{Mn}^{4+} is shown in Figure 3a, while the comparison of the thermal luminescence maps for all analyzed phosphors is shown in Figure 3b-Figure 3e (see also Figure S1-Figure 4). Based on the thermal dependence of the integrated Mn4+\mathrm{Mn}^{4+} emission intensity in the investigated double perovskites (Figure 3f), the temperature at which the intensity decreases to 50% of the low temperature value (T50T_{50}) was estimated (Figure 3g). The main mechanism responsible for thermal depopulation of the emitting state of Mn4+\mathrm{Mn}^{4+} ions is associated with the intersection point between the 2E{}^{2}\mathrm{E} and 4T2{}^{4}\mathrm{T}_{2} states parabola. Therefore, to analyze the thermal stability of the Mn4+\mathrm{Mn}^{4+} luminescence, the activation energy for thermal quenching (EaE_a) was calculated using the relation:

Thermal evolution of emission spectra and thermal dependence of emission intensities, T50, and Ea

Figure 3. Thermal evolution of emission spectra of Ba2InNbO6:Mn4+\mathrm{Ba}_{2}\mathrm{InNbO}_{6}:\mathrm{Mn}^{4+} - a); thermal maps of normalized emission spectra of Sr2InTaO6:Mn4+\mathrm{Sr}_{2}\mathrm{InTaO}_{6}:\mathrm{Mn}^{4+} - b); Sr2InNbO6:Mn4+\mathrm{Sr}_{2}\mathrm{InNbO}_{6}:\mathrm{Mn}^{4+} - c); Ba2InTaO6:Mn4+\mathrm{Ba}_{2}\mathrm{InTaO}_{6}:\mathrm{Mn}^{4+} - d); Ba2InNbO6:Mn4+\mathrm{Ba}_{2}\mathrm{InNbO}_{6}:\mathrm{Mn}^{4+} - e); thermal dependence of integral emission intensities of Mn4+\mathrm{Mn}^{4+} ions in the analyzed host materials – f); corresponding T50T_{50} – g); and EaE_{a} - h).

Luminescence decay profiles and thermal dependences of lifetime and sensitivity for Mn$^{4+}$-doped phosphors

Figure 4. Luminescence decay profile of the Mn4+^{4+} ions in Ba2_2InTaO6_6:Mn4+^{4+} measured as a function of temperature– a); thermal dependence of τavr\tau_{\mathrm{avr}} for analyzed phosphors - b) and corresponding SAS_A - c), the SAMAXS_{A\mathrm{MAX}} for different phosphors – d); thermal dependence of SRS_R – e) and SRMAXS_{R\mathrm{MAX}} for different host material compositions – f).

ln⁡(I0I)=ln⁡(A)−EakT(10)\ln\left(\frac{I_0}{I}\right)=\ln(A)-\frac{E_a}{kT} \tag*{(10)}

where I0I_0 and II are the integrated intensities of the emission spectra at lowest temperature and given temperature T, respectively, AA is a constant and kk refers to the Boltzmann constant (Figure 3h). The obtained data shows that both EaE_a and T50T_{50} follow the trend Ba2InNbO6<Ba2InTaO6<Sr2InNbO6<Sr2InTaO6\mathrm{Ba}_{2}\mathrm{InNbO}_{6}<\mathrm{Ba}_{2}\mathrm{InTaO}_{6}<\mathrm{Sr}_{2}\mathrm{InNbO}_{6}<\mathrm{Sr}_{2}\mathrm{InTaO}_{6}. Thermal quenching is therefore more pronounced in the Ba2+\mathrm{Ba}^{2+}-based compounds compared with their Sr2+\mathrm{Sr}^{2+}-based counterparts. Among all investigated compositions, Ba2InNbO6:Mn4+\mathrm{Ba}_{2}\mathrm{InNbO}_{6}:\mathrm{Mn}^{4+} exhibits the most rapid loss of emission intensity with increasing temperature, whereas Sr2InTaO6:Mn4+\mathrm{Sr}_{2}\mathrm{InTaO}_{6}:\mathrm{Mn}^{4+} displays the highest thermal stability. Within each isostructural pair, the Ta5+\mathrm{Ta}^{5+}-containing analogues show higher EaE_a and T50T_{50} values than the corresponding Nb5+\mathrm{Nb}^{5+}-based compositions. As will be explained later in the text these results can be rationalized based on the energy separation between the zero-phonon levels of the 2E{}^{2}\mathrm{E} and 4T2{}^{4}\mathrm{T}_{2} states since thermal quenching proceeds via the 2E→4T2→4A2{}^{2}\mathrm{E}\rightarrow{}^{4}\mathrm{T}_{2}\rightarrow{}^{4}\mathrm{A}_{2} crossover mechanism.

The thermal quenching of the Mn4+\mathrm{Mn}^{4+} emission intensity is expected to influence the luminescence kinetics of the 2E{}^{2}\mathrm{E} state. At low temperatures, the decay is characterized by long τavr\tau_{avr} values, reflecting the slow nonradiative relaxation of electrons in the 2Eg{}^{2}\mathrm{E}_{g} state (Figure 4a, Figure S5-Figure 7). As the temperature increases, τavr\tau_{avr} becomes shorter, indicating that thermal activation enhances nonradiative pathways. Consistent with the previously determined activation energies (EaE_a), the Ba2+\mathrm{Ba}^{2+}-based compounds exhibit very rapid thermal shortening of τavr\tau_{\mathrm{avr}} (Figure 4b). In contrast, the Sr2+\mathrm{Sr}^{2+}-based materials show smoother decay curves, with τavr\tau_{\mathrm{avr}} decreasing gradually with temperature, in agreement with their emission-intensity trends. For the Ba2+\mathrm{Ba}^{2+} compounds, the τavr\tau_{\mathrm{avr}} profile is sensitive to changes at the B′B' site, whereas such B′B'-site variations have little effect on the thermal evolution of τavr\tau_{\mathrm{avr}} in the Sr2+\mathrm{Sr}^{2+} analogues. Notably, Ba2InNbO6:Mn4+\mathrm{Ba}_2\mathrm{In}\mathrm{NbO}_6:\mathrm{Mn}^{4+} shows almost negligible temperature-induced variation in τavr\tau_{\mathrm{avr}}. To quantify the thermal shortening of τavr\tau_{\mathrm{avr}} in the analyzed phosphors the absolute SAS_A and relative sensitivity SRS_R were calculated as follows:

Three scatter plots showing the influence of $\beta_1$ on $\tau_{\mathrm{avr}}$ (a), $S_{\mathrm{AMAX}}$ (b), and $S_{\mathrm{RMAX}}$ (c), with data for Sr$_2$InTaO$_6$, Sr$_2$InNbO$_6$, Ba$_2$InTaO$_6$, and Ba$_2$InNbO$_6$

Figure 7. The influence of the β1\beta_1 on the τavr\tau_{\mathrm{avr}} – a), SAMAXS_{\mathrm{AMAX}} – b) and SRMAXS_{\mathrm{RMAX}} – c) for the analyzed group of Mn4+^{4+} doped phosphors.

SA=ΔτΔT(11)S_A = \frac{\Delta\tau}{\Delta T} \tag*{(11)}
SR=1τΔτΔT×100%(12)S_R = \frac{1}{\tau}\frac{\Delta\tau}{\Delta T} \times100\% \tag*{(12)}

where Δτavr\Delta\tau_{\mathrm{avr}} represents the change in the τavr\tau_{\mathrm{avr}} corresponding to the change of temperature by ΔT\Delta T.

In the case of all analyzed phosphors a single dominant maximum in SAS_A can be found, which value and the corresponding temperature at which it occurs are tuned with the modification in the host material composition (Figure 4c). The SAMAXS_{A\mathit{MAX}} determined for the investigated phosphors are as follows: 1.4 μ\mus K−1^{-1} at 283 K for Sr2InTaO6:Mn4+\mathrm{Sr}_2\mathrm{In}\mathrm{TaO}_6:\mathrm{Mn}^{4+}, 1.165 μ\mus K−1^{-1} at 242 K for Sr2InNbO6:Mn4+\mathrm{Sr}_2\mathrm{In}\mathrm{NbO}_6:\mathrm{Mn}^{4+}, 0.428 μ\mus K−1^{-1} at 222 K for Ba2InTaO6:Mn4+\mathrm{Ba}_2\mathrm{In}\mathrm{TaO}_6:\mathrm{Mn}^{4+} and 0.112 μ\mus K−1^{-1} at 108 K for Ba2InNbO6:Mn4+\mathrm{Ba}_2\mathrm{In}\mathrm{NbO}_6:\mathrm{Mn}^{4+} (Figure 4d). In the case of SRS_R, the obtained results revealed that Ba2InTaO6:Mn4+\mathrm{Ba}_2\mathrm{In}\mathrm{TaO}_6:\mathrm{Mn}^{4+} and Ba2InNbO6:Mn4+\mathrm{Ba}_2\mathrm{In}\mathrm{NbO}_6:\mathrm{Mn}^{4+} reach maximum SRS_R values of 1.0 % K−1^{-1} at 230 K and 0.49 % K−1^{-1} at 110 K, respectively, after which their SRS_R values decrease sharply (Figure 4e). In contrast, Sr2InNbO6:Mn4+\mathrm{Sr}_2\mathrm{In}\mathrm{NbO}_6:\mathrm{Mn}^{4+} exhibits an SRS_R = 1.2 % K−1^{-1} at 280 K, while Sr2InTaO6:Mn4+\mathrm{Sr}_2\mathrm{In}\mathrm{TaO}_6:\mathrm{Mn}^{4+} reaches SRS_R = 1.8 % K−1^{-1} at 307 K (Figure 4f). Moreover, when comparing the temperature at which the SRS_R reaches its maximum (T@SmaxT@S_{max}) in relation to changes at the B′B' site, a correlation with the average Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} distance was observed. For Sr2+\mathrm{Sr}^{2+}-based compounds, increasing the crystal field strength by substituting Ta5+^{5+} to Nb5+^{5+} at the B′B' site leads to a decrease in T@Smax⁡T@S_{\max}. A similar trend is observed in the Ba2+^{2+}-based hosts, where replacing Ta5+^{5+} with Nb5+^{5+} likewise leads to a reduction in T@Smax⁡T@S_{\max}.

To establish a methodology for designing lifetime-based luminescent thermometers employing Mn4+^{4+} ions, it is essential to identify the factors governing their relative sensitivity and to elucidate how these factors are modulated by the structural parameters of the host lattice. The most important thermometric parameter, which is the relative sensitivity SRS_R referenced also in Equation 11, can alternatively be expressed in a form that utilize SAS_A, namely:

SR=1τΔτΔT×100%=1τSA(13)S_R=\frac{1}{\tau}\frac{\Delta\tau}{\Delta T}\times100\%=\frac{1}{\tau}S_A \tag*{(13)}

From this expression, it is evident that two principal aspects must be addressed when thinking about the modification of the sensitivity of the lifetime-based thermometer: the dependence of the lifetime τavr\tau_{avr} on the host material, and the influence of the host material on the temperature-induced dynamics of τavr\tau_{avr}. The general expression describing the probability of depopulation of the excited state includes contributions from both radiative and nonradiative processes, as follows[79]:

1τ=WR+WNR=1τ0+WNR(14)\frac{1}{\tau}=W_{\mathrm{R}}+W_{\mathrm{NR}}=\frac{1}{\tau_{0}}+W_{\mathrm{NR}} \tag*{(14)}

At low temperatures, the probability of nonradiative depopulation (WNRW_{\mathrm{NR}}) is relatively small for Mn4+\mathrm{Mn}^{4+} ions due to the high activation barrier associated with the nonradiative relaxation of the 2E{}^{2}\mathrm{E} state. Consequently, the influence of the host material on τR\tau_{\mathrm{R}} becomes a major factor in these considerations. A preliminary inspection of the SRS_{\mathrm{R}} expression indicates that, from the perspective of maximizing sensitivity of luminescence thermometer, it is advantageous for the 2E{}^{2}\mathrm{E} state to exhibit a short τavr\tau_{avr}. In transition metal ions with a 3d33d^{3} electronic configuration, such as Mn4+\mathrm{Mn}^{4+}, the spin-orbit coupling between the 2E{}^{2}\mathrm{E} and 4T2{}^{4}\mathrm{T}_{2} states exerts a strong and dominant effect on the radiative lifetime τR\tau_{\mathrm{R}}. Therefore, τR\tau_{\mathrm{R}} strongly depends on the energy gap between the 2E{}^{2}\mathrm{E} and 4T2{}^{4}\mathrm{T}_{2} levels (Δ\Delta) and the lifetime of the 4T2{}^{4}\mathrm{T}_{2} state (τT\tau_{\mathrm{T}})[80]. Therefore, the radiative lifetime of the 2E{}^{2}\mathrm{E} doublet state depends primarily on the doublet-quartet energy separation (Δ\Delta).

Figure 5a presents the values of Δ\Delta for the investigated double perovskites. The Sr2+\mathrm{Sr}^{2+}-based compounds exhibit larger Δ\Delta values than their Ba2+\mathrm{Ba}^{2+}-based analogues. This may be related with the shorter average Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond distances and correspondingly higher crystal-field strength (DqDq) in the Sr2+\mathrm{Sr}^{2+} phases. Substituting Ta5+\mathrm{Ta}^{5+} with Nb5+\mathrm{Nb}^{5+} produces only a modest decrease of ∼50 cm−1\sim50\ \mathrm{cm}^{-1} in for the Sr2+\mathrm{Sr}^{2+} compounds, whereas in the Ba2+\mathrm{Ba}^{2+} compounds the same substitution increases Δ\Delta by ∼225 cm−1\sim225\ \mathrm{cm}^{-1}. These contrasting trends indicate that the octahedral crystal-field strength and Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bonding covalence are similar within the Sr2+\mathrm{Sr}^{2+} series but differ substantially within the Ba2+\mathrm{Ba}^{2+} series. This is not surprising since Ba2InNbO6\mathrm{Ba}_{2}\mathrm{In}\mathrm{NbO}_{6} exhibits the highest Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} covalence among the compositions studied. In this case, enhanced covalence lowers the energy of the 2E{}^{2}\mathrm{E} level and raises that of the 4T2{}^{4}\mathrm{T}_{2} level, thereby increasing Δ\Delta (Table 2). This explains why Δ(Ba2InTaO6;2183 cm−1)\Delta(\mathrm{Ba}_{2}\mathrm{In}\mathrm{TaO}_{6}; 2183\ \mathrm{cm}^{-1}) is smaller than Δ(Ba2InNbO6;2408 cm−1)\Delta(\mathrm{Ba}_{2}\mathrm{In}\mathrm{NbO}_{6}; 2408\ \mathrm{cm}^{-1}). The dependence of the τR\tau_{R} on the energy separation Δ\Delta shown in Figure 5b reveals that the Sr2+\mathrm{Sr}^{2+}-based compounds exhibit longer τR\tau_{R} values than the Ba2+\mathrm{Ba}^{2+}-based analogues, consistent with the expectation from Eq. (14), since Δ\Delta is larger in the Sr2+\mathrm{Sr}^{2+} compounds. However, despite the higher Δ\Delta value of Ba2InNbO6\mathrm{Ba}_{2}\mathrm{In}\mathrm{NbO}_{6}, its τR\tau_{R} is significantly shorter than that of Ba2InTaO6\mathrm{Ba}_{2}\mathrm{In}\mathrm{TaO}_{6}. We attribute this behaviour to the stronger hybridization between the O 2p2p orbitals and the Mn4+\mathrm{Mn}^{4+} dd orbitals in Ba2InNbO6\mathrm{Ba}_{2}\mathrm{In}\mathrm{NbO}_{6}, which relaxes the spin-forbidden nature of the 2Eg→4A2g{}^{2}\mathrm{E}_{g}\rightarrow{}^{4}\mathrm{A}_{2g} transition. The increased transition probability also accounts for the higher intensity of the zero-phonon RR-line observed in Ba2InNbO6\mathrm{Ba}_{2}\mathrm{In}\mathrm{NbO}_{6}. Figure 5c shows the variation of τR\tau_{R} as a function of DqDq. The Sr2+\mathrm{Sr}^{2+}-based compounds with shorter Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond distance and therefore higher DqDq exhibits longer τR\tau_{R} values than the Ba2+\mathrm{Ba}^{2+}-based analogues. Therefore, in general, the strength of the crystalline field can be used to tune the τR\tau_{R} values. On the other hand, direct correlation between the energy of the 2E{}^{2}\mathrm{E} state and the τR\tau_{R} was not found for the analyzed host materials (Figure 5d). Since the energy of the 4T2{}^{4}\mathrm{T}_{2} state is also dependent on the covalency of the Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond, the linear correlation was found between the β1\beta_{1} parameter as a function of Δ\Delta (Figure 5e). Hence, as shown in Figure 5f, the higher is the bonding covalence, the shorter is τR\tau_{R}. This is again related to the relaxation of the spin selection rule by the enhanced hybridization between the Mn4+\mathrm{Mn}^{4+} dd orbitals and the O 2p2p orbitals. Therefore, it becomes evident that, from the standpoint of achieving a short τR\tau_{R}, which may positively affect the relative sensitivity SRS_{R} it is advantageous to employ host materials characterized by low β1\beta_{1} values; that is, materials in which the Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond exhibits a higher degree of covalency.

The dependence of the analyzed host materials and parameters affecting the average lifetime

Figure 5. The Δ\Delta for the analyzed host materials – a); the influence of the Δ\Delta on the τavr\tau_{avr} – b); the influence of the energy of the 4T2^{4}T_{2} state – c) and of the 2E^{2}E state – d) on the τavr\tau_{avr}; the β1\beta_{1} as a function of Δ\Delta – e) and the influence of the β1\beta_{1} parameter on the τavr\tau_{avr} – f).

Another aspect influencing the SRS_{R} is the thermal dependence of the τavr\tau_{avr}. The general expression describing the processes governing the temperature-induced evolution of the τavr\tau_{avr} is given by[80]:

τE=τstat(1+exp⁡(−hωkT)+3exp⁡(−ΔkT))(1+τstatτdynexp⁡(−hωkT))((VS−OΔt)2+3exp⁡(−ΔkT))(15)\tau_{E}=\frac{\tau_{stat}\left(1+\exp\left(\frac{-h\omega}{kT}\right)+3\exp\left(\frac{-\Delta}{kT}\right)\right)}{\left(1+\frac{\tau_{stat}}{\tau_{dyn}}\exp\left(\frac{-h\omega}{kT}\right)\right)\left(\left(\frac{V_{S}-O}{\Delta^{t}}\right)^{2}+3\exp\left(\frac{-\Delta}{kT}\right)\right)} \tag*{(15)}

where, τstat\tau_{stat}, τdyn\tau_{dyn}, hωh\omega, Δ\Delta, Δt\Delta_{t}, VS−OV_{S-O} and kk represent radiative transition kinetic parameter generated by static odd parity crystal field and probability of radiative transition generated by odd parity crystal vibration, phonon mode of the host materials, real energy difference between 2E^{2}E and 4T2^{4}T_{2} states, and the energy difference determined from excitation spectrum, spin-orbital coupling constant and Boltzmann constant, respectively.

Although this equation provides a comprehensive description of the underlying processes, its practical application is challenging due to its mathematical complexity. From a thermometric design perspective, it is particularly important to understand how material-specific parameters influence both SAMAXS_{AMAX} and the corresponding temperature T@SAMAXT@S_{AMAX}, as these determine the suitability of a luminescent thermometer for a specific application. In the analysed phosphors, the value of SAMAXS_{AMAX} increases substantially with relatively small variations in the β1\beta_{1} parameter (Figure 6b). This behaviour may be attributed to the strong dependence of the 4T2{}^{4}T_{2} energy level and consequently the activation energy EaE_{a} on the parameter β1\beta_{1}. In principle, Δ\Delta is not expected to exhibit thermal sensitivity; however, changes in the 4T2{}^{4}T_{2} energy simultaneously modify EaE_{a}, and thermalization from the 2E{}^{2}E to the 4T2{}^{4}T_{2} level is widely recognized as the dominant process governing the thermal sensitivity of Mn4+\mathrm{Mn}^{4+} luminescence kinetics. In Sr2+\mathrm{Sr}^{2+}-based compounds, as the B′B' site changes from Ta5+\mathrm{Ta}^{5+} to Nb5+\mathrm{Nb}^{5+}, the Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond length decreases, leading to a decrease in BB value due to stronger delocalization of 3d3d electrons, accompanied by a decrease in β1\beta_{1}. This indicates an increase in covalency, explaining why Sr2InNbO6:Mn4+\mathrm{Sr}_{2}\mathrm{InNbO}_{6}\mathrm{:Mn}^{4+} exhibits greater covalent character than Sr2InTaO6:Mn4+\mathrm{Sr}_{2}\mathrm{InTaO}_{6}\mathrm{:Mn}^{4+}. In contrast, for Ba2+\mathrm{Ba}^{2+} compounds, the decrease in Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond length from Nb5+\mathrm{Nb}^{5+} to Ta5+\mathrm{Ta}^{5+} results in an increase in β1\beta_{1}, indicating greater ionicity in Ba2InTaO6\mathrm{Ba}_{2}\mathrm{InTaO}_{6} compared to Ba2InNbO6:Mn4+\mathrm{Ba}_{2}\mathrm{InNbO}_{6}\mathrm{:Mn}^{4+}. Similarly to SAMAXS_{AMAX}, the T@SAMAXT@S_{AMAX} also increases markedly with small changes in β1\beta_{1} (Figure 6b and Figure 6c, respectively). The influence of the 4T2{}^{4}T_{2} energy level on the thermal depopulation of the 2E{}^{2}E state and thus on its thermal stability can be further illustrated by examining the relationship between the T50T_{50} parameter, which directly characterizes the thermal stability of Mn4+\mathrm{Mn}^{4+} emission intensity, and SAMAXS_{AMAX} (Figure 6e). A key factor contributing to thermally stable luminescence is the structural rigidity imparted by ordered host structures. In the group of phosphors analyzed, the Sr2+\mathrm{Sr}^{2+}-based compounds, which have shorter Mn4+\mathrm{Mn}^{4+}-O2−\mathrm{O}^{2-} bond length than Ba2+^{2+}-based hosts, exhibit higher thermal stability. This can be attributed to the smaller atomic size of Sr2+^{2+} which causes contraction and slight geometric distortion at the AA site, thereby promoting greater cationic ordering at the B′B' site. As a result, due to the smaller AA site ions and lower crystal symmetry, the degree of BB-site cationic order (In5+^{5+}-Nb5+^{5+} or In5+^{5+}-Ta5+^{5+}) in Sr2_2In(Nb/Ta)O6_6:Mn4+^{4+} is expected to be higher than that in the cubic Ba2_2In(Nb/Ta)O6_6:Mn4+^{4+} system, which accounts for the enhanced thermal stability of the Sr2+^{2+} based hosts. The highly monotonic correlation shown in Figure 6e provides direct evidence for this relationship, although the detailed mechanism remains insufficiently understood. As expected, T@SAMAXT@S_{AMAX} is identical to T50T_{50}, since both parameters describe the same underlying thermal depopulation process of the 2^{2}E state, a conclusion further supported by the linear dependence presented in Figure 6f.

Six-panel plots showing relationships among thermal stability parameters for four hosts

Figure 6. The influence of the T@SAMAXT@S_{AMAX} on the SAMAXS_{AMAX} – a); the SAMAXS_{AMAX} as a function of β1\beta_1 parameter – b) the influence of the β1\beta_1 parameter on the T@SAMAXT@S_{AMAX} – c); the dependence of the SAMAXS_{AMAX} on the energy of the 2^{2}E state – d) and the T50T_{50} - e); The T@SAMAXT@S_{AMAX} as a function of T50T_{50} – f).

Since SRS_R depends on both the τavr\tau_{avr} and SAS_A, establishing correlations between these parameters and the physicochemical characteristics of the host material is highly desirable. Notably, the β1\beta_1 parameter exerts a pronounced influence on both τavr\tau_{avr} and SAMAXS_{AMAX}. This observation is particularly significant, as it was initially anticipated that the Dq/BDq/B ratio would play the dominant role in governing the thermometric response. However, as demonstrated above, distortion of the crystallographic site symmetry occupied by Mn4+\mathrm{Mn}^{4+} ions can substantially modify their spectroscopic properties. The clear linear correlations between τavr\tau_{avr} (Figure 7a) and β1\beta_1, as well as between SAMAXS_{AMAX} (Figure 7b) and β1\beta_1, combined with the absence of a direct relationship between these parameters and Dq/BDq/B (Figure S8), indicate that β1\beta_1 is a more reliable descriptor for predicting the thermometric performance of lifetime-based luminescence thermometers. The dependence of τavr\tau_{avr} on β1\beta_1 is described by the experimental relationship as follows:

τavr(β1)=5.91⋅β1−5.6744(16)\tau_{avr}(\beta_1)=5.91\cdot\beta_1-5.6744 \tag*{(16)}

On the other hand, SAMAXS_{AMAX} can likewise be expressed as a function of β1\beta_1:

SAmax⁡(β1)=28.112⋅β1+26.988(17)S_{A\max}(\beta_1)=28.112\cdot\beta_1+26.988 \tag*{(17)}

Consequently, according to Eq. (13), SRMAXS_{RMAX} may also be formulated as a function of β1\beta_1:

SRmax⁡=28.112⋅β1+26.9885.91⋅β1−5.6744(18)S_{R\max}=\frac{28.112\cdot\beta_1+26.988}{5.91\cdot\beta_1-5.6744} \tag*{(18)}

As illustrated in Figure 7c, this experimentally derived relationship accurately reproduces the observed dependence of SRMAXS_{RMAX} on β1\beta_1. Although the equation is specific to the analyzed group of materials and requires further validation across a broader range of phosphors, it provides valuable guidance for the rational design of lifetime-based thermometers with targeted thermometric performance.

Conclusions

In summary, this work presents a systematic investigation of the influence of host composition on the thermometric performance of Mn4+^{4+}-activated lifetime-based luminescence thermometers in four double perovskite materials, namely Sr2_2InTaO6_6:Mn4+^{4+}, Sr2_2InNbO6_6:Mn4+^{4+}, Ba2_2InTaO6_6:Mn4+^{4+} and Ba2_2InNbO6_6:Mn4+^{4+}. The Sr2+^{2+}-based phosphors crystallize in a monoclinic structure, whereas their Ba2+^{2+}-based counterparts adopt a cubic phase. In the Ba2+^{2+}-based hosts, Mn4+^{4+} ions occupy nearly perfect octahedral sites. Substitution of Ba2+^{2+} with Sr2+^{2+} induces octahedral tilting and lowers the point symmetry of the Mn4+^{4+}-occupied sites. Structural analysis indicates that differences in ionic radii between In3+^{3+} and Nb5+^{5+}/Ta5+^{5+} promote BB/B′B' site disorder, which is more pronounced in the higher-symmetry Ba2+^{2+}-based compounds. Replacement of Ba2+^{2+} by Sr2+^{2+} at the AA site results in a blueshift of the Mn4+^{4+} absorption bands, whereas substitution of Nb5+^{5+} with Ta5+^{5+} at the B′B' site only marginally affects their spectral positions. The nephelauxetic parameter β1\beta_1 decreases for Ba2+^{2+}-based phosphors, indicating increased Mn4+^{4+}-O2−^{2-} covalency, attributed to enhanced Mn4+^{4+} t2gt_{2g}–O2−^{2-} pπp\pi orbital overlap in the highly symmetric environment despite longer bond distances. Optimization analysis reveals that maximizing relative sensitivity (SRS_R) favours hosts with small 2E^{2}E - 4T2^{4}T_2 energy separation and low β1\beta_1 values, whereas the temperature sensitivity of the average lifetime (SAMAXS_{\mathrm{AMAX}}) increases with increasing β1\beta_1 and shifts to higher temperatures. Overall, thermometric performance is predominantly governed by the thermal evolution of SAS_A, suggesting that tuning this parameter is key to improving Mn4+^{4+}-based lifetime thermometers in double perovskites.

Although the conclusions drawn in this study are based on a limited set of host materials and require further systematic investigation to confirm the general validity of the proposed hypotheses, the design principles outlined herein provide valuable guidance for materials engineering. In particular, they offer strategic directions for the rational development of lifetime-based luminescence thermometers with predefined and optimized thermometric performance.

Acknowledgements

This work was supported by the National Science Center (NCN) Poland under project no. DEC-2023/49/B/ST5/03384. Maja Szymczak gratefully acknowledges the support of the Foundation for Polish Science through the START program. Authors would like to acknowledge dr Damian Szymanski for SEM and EDS analyses.

References

  1. [1]E. Hemmer, P. Acosta-Mora, J. Méndez-Ramos, S. Fischer, Optical nanoprobes for biomedical applications: Shining a light on upconverting and near-infrared emitting nanoparticles for imaging, thermal sensing, and photodynamic therapy, J. Mater. Chem. B 5 (2017) 4365–4392. https://doi.org/10.1039/C7TB00403F.
  2. [2]R. Lv, P. Yang, F. He, S. Gai, C. Li, Y. Dai, G. Yang, J. Lin, A yolk-like multifunctional platform for multimodal imaging and synergistic therapy triggered by a single near-infrared light, ACS Nano 9 (2015) 1630–1647. https://doi.org/10.1021/NN5063613.
  3. [3]L. Chen, J.W. Ye, H.P. Wang, M. Pan, S.Y. Yin, Z.W. Wei, L.Y. Zhang, K. Wu, Y.N. Fan, C.Y. Su, Ultrafast water sensing and thermal imaging by a metal-organic framework with switchable luminescence, Nat. Commun. 8 (2017). https://doi.org/10.1038/NCOMMS15985.
  4. [4]E. Ximendes, E. Martín Rodríguez, D.H. Ortgies, M. Tan, G. Chen, B. del Rosal, Nanoparticles for In Vivo Lifetime Multiplexed Imaging, Methods in Molecular Biology 2350 (2021) 239–251. https://doi.org/10.1007/978-1-0716-1593-5_15.
  5. [5]G. Sutton, S. Korniliou, A. Andreu, D. Wilson, Imaging Luminescence Thermometry to 750 °C for the Heat Treatment of Common Engineering Alloys and Comparison with Thermal Imaging, Int. J. Thermophys. 43 (2022). https://doi.org/10.1007/S10765-021-02963-1.
  6. [6]O.S. Wolfbeis, An overview of nanoparticles commonly used in fluorescent bioimaging, Chem. Soc. Rev. 44 (2015) 4743–4768. https://doi.org/10.1039/C4CS00392F.
  7. [7]X.D. Wang, O.S. Wolfbeis, R.J. Meier, Luminescent probes and sensors for temperature, Chem. Soc. Rev. 42 (2013) 7834–7869. https://doi.org/10.1039/C3CS60102A.
  8. [8]C.D.S. Brites, S. Balabhadra, L.D. Carlos, Lanthanide-Based Thermometers: At the Cutting-Edge of Luminescence Thermometry, Adv. Opt. Mater. 7 (2019) 1801239. https://doi.org/10.1002/ADOM.201801239.
  9. [9]J. Rocha, C.D.S. Brites, L.D. Carlos, Lanthanide Organic Framework Luminescent Thermometers, Chemistry - A European Journal 22 (2016) 14782–14795. https://doi.org/10.1002/CHEM.201600860.
  10. [10]D. Jaque, F. Vetrone, Luminescence nanothermometry, Nanoscale 4 (2012) 4301–4326. https://doi.org/10.1039/C2NR30764B.
  11. [11]M.D. Dramićanin, Trends in luminescence thermometry, J. Appl. Phys. 128 (2020). https://doi.org/10.1063/5.0014825.
  12. [12]M.D. Dramićanin, Sensing temperature via downshifting emissions of lanthanide-doped metal oxides and salts. A review, Methods Appl. Fluoresc. 4 (2016). https://doi.org/10.1088/2050-6120/4/4/042001.
  13. [13]A. Bednarkiewicz, L. Marciniak, L.D. Carlos, D. Jaque, Standardizing luminescence nanothermometry for biomedical applications, Nanoscale 12 (2020) 14405–14421. https://doi.org/10.1039/D0NR03568H.
  14. [14]A. Bednarkiewicz, J. Drabik, K. Trejgis, D. Jaque, E. Ximendes, L. Marciniak, Luminescence based temperature bio-imaging: Status, challenges, and perspectives, Appl. Phys. Rev. 8 (2021). https://doi.org/10.1063/5.0030295.
  15. [15]L. Labrador-Páez, M. Pedroni, A. Speghini, J. García-Solé, P. Haro-González, D. Jaque, Reliability of rare-earth-doped infrared luminescent nanothermometers, Nanoscale 10 (2018) 22319–22328. https://doi.org/10.1039/C8NR07566B.
  16. [16]B.G. Wybourne, L. Smentek, Optical Spectroscopy of Lanthanides : Magnetic and Hyperfine Interactions, Optical Spectroscopy of Lanthanides (2007). https://doi.org/10.1201/9781420006933.
  17. [17]J.C.G. Bünzli, J.C.G. Bünzli, S. V. Eliseeva, S. V. Eliseeva, Intriguing aspects of lanthanide luminescence, Chem. Sci. 4 (2013) 1939–1949. https://doi.org/10.1039/C3SC22126A.
  18. [18]J.C.G. Bünzli, C. Piguet, Taking advantage of luminescent lanthanide ions, Chem. Soc. Rev. 34 (2005) 1048–1077. https://doi.org/10.1039/B406082M.
  19. [19]J.C.G. Bünzli, S. Comby, A.S. Chauvin, C.D.B. Vandevyver, New Opportunities for Lanthanide Luminescence, Journal of Rare Earths 25 (2007) 257–274. https://doi.org/10.1016/S1002-0721(07)60420-7.
  20. [20]T. Miyakawa, D.L. Dexter, Phonon Sidebands, Multiphonon Relaxation of Excited States, and Phonon-Assisted Energy Transfer between Ions in Solids, Phys. Rev. B 1 (1970) 2961. https://doi.org/10.1103/PhysRevB.1.2961.
  21. [21]K. Binnemans, Interpretation of europium(III) spectra, Coord. Chem. Rev. 295 (2015) 1–45. https://doi.org/10.1016/J.CCR.2015.02.015.
  22. [22]J.C.G. Bünzli, Lanthanide light for biology and medical diagnosis, J. Lumin. 170 (2016) 866–878. https://doi.org/10.1016/J.JLUMIN.2015.07.033.
  23. [23]W.M. Piotrowski, K. Maciejewska, L. Dalipi, B. Fond, L. Marciniak, Cr3+ ions as an efficient antenna for the sensitization and brightness enhancement of Nd3+, Er3+-based ratiometric thermometer in GdScO3 perovskite lattice, J. Alloys Compd. 923 (2022) 166343. https://doi.org/10.1016/J.JALLCOM.2022.166343.
  24. [24]L. Marciniak, W.M. Piotrowski, M. Szymczak, M. Pieprz, K. Trejgis, New Strategies to Improve Thermal Sensitivity and Temperature Resolution in Lanthanide-Doped Luminescent Thermometers, Luminescent Thermometry: Applications and Uses (2023) 69–103. https://doi.org/10.1007/978-3-031-28516-5_2.
  25. [25]W.W. Holloway, M. Kestigian, Concentration quenching of the Tb3+ ion fluorescence in Y3Al5O12 crystals, Physics Letters 21 (1966) 364–366. https://doi.org/10.1016/0031-9163(66)90484-7.
  26. [26]M.S. Pudovkin, A.K. Ginkel, E. V. Lukinova, Temperature sensitivity of Nd3+, Yb3+:YF3 ratiometric luminescent thermometers at different Yb3+ concentration, Opt. Mater. (Amst.). 119 (2021) 111328. https://doi.org/10.1016/J.OPTMAT.2021.111328.
  27. [27]N.M. Avram, M.G. Brik, Optical properties of 3d-ions in crystals: Spectroscopy and crystal field analysis, Optical Properties of 3d-Ions in Crystals: Spectroscopy and Crystal Field Analysis 9783642308383 (2013) 1–268. https://doi.org/10.1007/978-3-642-30838-3/COVER.
  28. [28]S. Adachi, Review—Mn 4+ -Activated Red and Deep Red-Emitting Phosphors, ECS Journal of Solid State Science and Technology 9 (2020) 016001. https://doi.org/10.1149/2.0022001JSS/XML.
  29. [29]S. Adachi, Luminescence spectroscopy of Cr3+ in an oxide: A strong or weak crystal-field phosphor?, J. Lumin. 234 (2021) 117965. https://doi.org/10.1016/J.JLUMIN.2021.117965.
  30. [30]L. Marciniak, K. Kniec, K. Elżbieciak-Piecka, K. Trejgis, J. Stefanska, M. Dramicanin, Luminescence thermometry with transition metal ions. A review, Coord. Chem. Rev. 469 (2022) 214671. https://doi.org/10.1016/J.CCR.2022.214671.
  31. [31]A.M. Srivastava, W.W. Beers, Luminescence of Mn4+ in the Distorted Perovskite Gd2MgTiO6, J. Electrochem. Soc. 143 (1996) L203–L205. https://doi.org/10.1149/1.1837087.
  32. [32]M.G. Brik, S.J. Camardello, A.M. Srivastava, N.M. Avram, A. Suchocki, Spin-Forbidden Transitions in the Spectra of Transition Metal Ions and Nephelauxetic Effect, ECS Journal of Solid State Science and Technology 5 (2016) R3067–R3077. https://doi.org/10.1149/2.0091601JSS.
  33. [33]S. Adachi, Review—Mn 4+ -Activated Red and Deep Red-Emitting Phosphors , ECS Journal of Solid State Science and Technology 9 (2020) 016001. https://doi.org/10.1149/2.0022001JSS.
  34. [34]M.G. Brik, A.M. Srivastava, On the optical properties of the Mn 4 ion in solids, J. Lumin. 133 (2013) 69–72. https://doi.org/10.1016/J.JLUMIN.2011.08.047.
  35. [35]M.G. Brik, S.J. Camardello, A.M. Srivastava, Influence of Covalency on the Mn 4+ 2 E g → 4 A 2g Emission Energy in Crystals , ECS Journal of Solid State Science and Technology 4 (2015) R39–R43. https://doi.org/10.1149/2.0031503JSS.
  36. [36]T. Senden, R.J.A. Van Dijk-Moes, A. Meijerink, Quenching of the red Mn4+ luminescence in Mn4+-doped fluoride LED phosphors, Light Sci. Appl. 7 (2018). https://doi.org/10.1038/S41377-018-0013-1.
  37. [37]Q. Zhou, L. Dolgov, A.M. Srivastava, L. Zhou, Z. Wang, J. Shi, M.D. Dramićanin, M.G. Brik, M. Wu, Mn2+ and Mn4+ red phosphors: Synthesis, luminescence and applications in WLEDs. A review, J. Mater. Chem. C Mater. 6 (2018) 2652–2671. https://doi.org/10.1039/C8TC00251G.
  38. [38]A.P. Vink, A. Meijerink, Electron–phonon coupling of Cr3+ in YAG and YGG, J. Lumin. 87–89 (2000) 601–604. https://doi.org/10.1016/S0022-2313(99)00308-7.
  39. [39]Q. Zhou, L. Dolgov, A.M. Srivastava, L. Zhou, Z. Wang, J. Shi, M.D. Dramićanin, M.G. Brik, M. Wu, Mn2+ and Mn4+ red phosphors: synthesis, luminescence and applications in WLEDs. A review, J. Mater. Chem. C Mater. 6 (2018) 2652–2671. https://doi.org/10.1039/C8TC00251G.
  40. [40]M.G. Brik, A.M. Srivastava, On the optical properties of the Mn4+ ion in solids, J. Lumin. 133 (2013) 69–72. https://doi.org/10.1016/J.JLUMIN.2011.08.047.
  41. [41]X. Wang, T. Zhang, Y. Lou, Y. Zhao, All-inorganic lead-free perovskites for optoelectronic applications, Mater. Chem. Front. 3 (2019) 365–375. https://doi.org/10.1039/C8QM00611C.
  42. [42]C. Shi, L. Ye, Z.X. Gong, J.J. Ma, Q.W. Wang, J.Y. Jiang, M.M. Hua, C.F. Wang, H. Yu, Y. Zhang, H.Y. Ye, Two-Dimensional Organic-Inorganic Hybrid Rare-Earth Double Perovskite Ferroelectrics, J. Am. Chem. Soc. 142 (2020) 545–551. https://doi.org/10.1021/JACS.9B11697.
  43. [43]L. Xu, J. Chen, J. Song, J. Li, J. Xue, Y. Dong, B. Cai, Q. Shan, B. Han, H. Zeng, Double-Protected All-Inorganic Perovskite Nanocrystals by Crystalline Matrix and Silica for Triple-Modal Anti-Counterfeiting Codes, ACS Appl. Mater. Interfaces 9 (2017) 26556–26564. https://doi.org/10.1021/ACSAMI.7B06436.
  44. [44]F. Zhao, Z. Song, J. Zhao, Q. Liu, Double perovskite Cs2AgInCl6:Cr3+: Broadband and near-infrared luminescent materials, Inorg. Chem. Front. 6 (2019) 3621–3628. https://doi.org/10.1039/C9QI00905A.
  45. [45]Z. Zhang, Y. Liang, H. Huang, X. Liu, Q. Li, L. Chen, D. Xu, Stable and Highly Efficient Photocatalysis with Lead-Free Double-Perovskite of Cs2AgBiBr6, Angewandte Chemie - International Edition 58 (2019) 7263–7267. https://doi.org/10.1002/ANIE.201900658.
  46. [46]Q. Cao, L. Li, Y. Wang, W. Wang, H. Chen, Y. Pan, X. Wei, Y. Li, Synthesis and optical properties of far-red dual perovskite Sr2InTaO6: Mn4+ phosphors for indoor plant lighting LED, J. Lumin. 252 (2022). https://doi.org/10.1016/J.JLUMIN.2022.119351.
  47. [47]Y. Li, C. Li, J. Kong, H. Su, L. Zhou, R. Yang, Y. Shang, C. Wang, J. Lian, G. Zhang, R. Yu, Thermally stable novel double perovskite orange-red emitting Sr2InTaO6:Sm3+ phosphors with high CRI for WLEDs, Ceram. Int. 49 (2023) 17488–17496. https://doi.org/10.1016/J.CERAMINT.2023.02.116.
  48. [48]J. Zhao, H. Gao, H. Xu, Z. Zhao, H. Bu, X. Cao, L. He, Z. Yang, J. Sun, Structure and photoluminescence of Eu3+doped Sr2InTaO6red phosphor with high color purity, RSC Adv. 11 (2021) 8282–8289. https://doi.org/10.1039/D1RA00165E.
  49. [49]L. Xiang, X. Zhou, L. Li, F. Ling, Y. Li, J. Li, H. Yang, Comparative study on the anomalous intense 5D0→7F4 emission in Eu3+ doped Sr2MNbO6 (M=Ga, In, Gd) phosphors, J. Lumin. 267 (2024). https://doi.org/10.1016/J.JLUMIN.2023.120370.
  50. [50]Y. Hua, H. Li, T. Wang, J.S. Yu, L. Li, Customization of novel double-perovskite (Ca,Sr)2InNbO6:Mn4+ red-emitting phosphors for luminescence lifetime thermometers with good relative sensing sensitivity, J. Alloys Compd. 925 (2022). https://doi.org/10.1016/J.JALLCOM.2022.166498.
  51. [51]A. Dutta, S.K. Singh, V.R.K. Murthy, P.K. Mukhopadhyay, T.P. Sinha, Crystal structure, Raman spectroscopy and microwave dielectric properties of xBa3MgNb2O9−(1−x)Ba2InNbO6 [x = 0.4, 0.6, 0.8], Mater. Res. Bull. 100 (2018) 178–183. https://doi.org/10.1016/J.MATERRESBULL.2017.12.014.
  52. [52]V. Ting, Y. Liu, R.L. Withers, L. Norén, M. James, J.D.F. Gerald, A structure and phase analysis investigation of the “1:1” ordered A2InNbO6 perovskites (A=Ca2+, Sr2+, Ba2+), J. Solid State Chem. 179 (2006) 551–562. https://doi.org/10.1016/J.JSSC.2005.11.012.
  53. [53]B. Rameshe, R. Murugan, B. Palanivel, First principle study on electronic structure, structural phase stability, optical and vibrational properties of Ba2ScMoO6 (M = Nb, Ta), Int. J. Mod. Phys. B 30 (2016). https://doi.org/10.1142/S021797921550246X.
  54. [54]T.S. Hammink, W.T. Fu, D.J.W. Ijdo, Crystal structure of Ba2InTaO6 as determined by the Rietveld refinement, J. Solid State Chem. 184 (2011) 848–851. https://doi.org/10.1016/J.JSSC.2011.02.011.
  55. [55]Q. Zhou, T.Y. Tan, B.J. Kennedy, J.R. Hester, Crystal structures and phase transitions in Sr doped Ba 2InTaO6 perovskites, J. Solid State Chem. 206 (2013) 122–128. https://doi.org/10.1016/J.JSSC.2013.08.007.
  56. [56]S.A. Dar, R. Sharma, V. Srivastava, U.K. Sakalle, Investigation on the electronic structure, optical, elastic, mechanical, thermodynamic and thermoelectric properties of wide band gap semiconductor double perovskite Ba2InTaO6, RSC Adv. 9 (2019) 9522–9532. https://doi.org/10.1039/C9RA00313D.
  57. [57]A. Dias, L.A. Khalam, M.T. Sebastian, R.L. Moreira, Raman-spectroscopic investigation of Ba2 InTaO6 and Sr2 InTaO6 perovskites, J. Solid State Chem. 180 (2007) 2143–2148. https://doi.org/10.1016/J.JSSC.2007.05.021.
  58. [58]V.M. Goldschmidt, Die Gesetze der Krystallochemie, Naturwissenschaften 14 (1926) 477–485. https://doi.org/10.1007/BF01507527/METRICS.
  59. [59]J. Zhang, C.J. Bennett, M.K. Nicholas, B.G. Mullens, B.J. Kennedy, Expected and unexpected structural phase transitions in K2ReBr6 and K2ReI6, J. Solid State Chem. 338 (2024). https://doi.org/10.1016/J.JSSC.2024.124875.
  60. [60]S. Kumawat, M. Rani, D.K. Meena, Anuradha, H.S. Mund, G. Arora, Frequency and temperature dependent impedance, conductivity and dielectric properties of Gd2FeCr0.75Mg0.25O6 for high-temperature electronics, Ceram. Int. 51 (2025) 38620–38630. https://doi.org/10.1016/J.CERAMINT.2025.06.099.
  61. [61]V. V. Tomaev, A.G. Syrkov, M.M. Sychev, Disordering and Conversion of Lead Selenide into an Efficient Ferroelectric Based on Lead Selenite, Glass Physics and Chemistry 49 (2023) 319–326. https://doi.org/10.1134/S1087659623600187.
  62. [62]Z. Chen, S. Du, K. Zhu, Z. Tian, J. Zhang, F. Li, S. Zhang, S. Zhao, W. Cui, X. Yuan, K. Chen, G. Yuan, G. Liu, Mn4+-Activated Double-Perovskite-Type Sr2LuNbO6 Multifunctional Phosphor for Optical Probing and Lighting, ACS Appl. Mater. Interfaces 15 (2023) 28193–28203. https://doi.org/10.1021/ACSAMI.3C03897/ASSET/IMAGES/LARGE/AM3C03897_0010.JPEG.
  63. [63]R.D. Shannon, Revised effective ionic radii and systematic studies of interatomic distances in halides and chalcogenides, Acta Crystallographica Section A 32 (1976) 751–767. https://doi.org/10.1107/S0567739476001551.
  64. [64]A.A. Elbadawi, O.A. Yassin, A.A. Gismelseed, Effect of the internal pressure and the anti-site disorder on the structure and magnetic properties of ALαFeTiO 6 (A=Ca, Sr, Ba) double perovskite oxides, J. Magn. Magn. Mater. 326 (2013) 1–6. https://doi.org/10.1016/J.JMMM.2012.07.035.
  65. [65]N. Menéndez, M. García-Hernández, D. Sánchez, J.D. Tornero, J.L. Martínez, J.A. Alonso, Charge transfer and disorder in double perovskites, Chemistry of Materials 16 (2004) 3565–3572. https://doi.org/10.1021/CM049305T.
  66. [66]Preparation, crystal and magnetic structure of the double perovskites Ba2CoBO6 (B = Mo, W)-Web of Science Core Collection, (n.d.). [67] A. Dias, L.A. Khalam, M.T. Sebastian, R.L. Moreira, Raman-spectroscopic investigation of Ba2InTaO6 and Sr2InTaO6 perovskites, J. Solid State Chem. 180 (2007) 2143–2148. https://doi.org/10.1016/J.JSSC.2007.05.021.
  67. [68]M.C. Viola, M.J. Martínez-Lope, J.A. Alonso, J.L. Martínez, J.M. De Paoli, S. Pagola, J.C. Pedregosa, M.T. Fernández-Díaz, R.E. Carbonio, Structure and magnetic properties of Sr2CoWO6: An ordered double perovskite containing Co2+(HS) with unquenched orbital magnetic moment, Chemistry of Materials 15 (2003) 1655–1663. https://doi.org/10.1021/CM0208455.
  68. [69]C. Meneghini, S. Ray, F. Liscio, F. Bardelli, S. Mobilio, D.D. Sarma, Nature of “disorder” in the ordered double perovskite Sr2FeMoO6, Phys. Rev. Lett. 103 (2009). https://doi.org/10.1103/PHYSREVLETT.103.046403.
  69. [70]M.C. Knapp, P.M. Woodward, A-site cation ordering in AA′BB′O6 perovskites, J. Solid State Chem. 179 (2006) 1076–1085. https://doi.org/10.1016/J.JSSC.2006.01.005.
  70. [71]O.N. Meetei, O. Erten, A. Mukherjee, M. Randeria, N. Trivedi, P. Woodward, Theory of half-metallic double perovskites. I. Double exchange mechanism, Phys. Rev. B Condens. Matter Mater. Phys. 87 (2013). https://doi.org/10.1103/PHYSREVB.87.165104.
  71. [72]M.C. Knapp, P.M. Woodward, A-site cation ordering in AA′BB′O6 perovskites, J. Solid State Chem. 179 (2006) 1076–1085. https://doi.org/10.1016/J.JSSC.2006.01.005.
  72. [73]C.J. Howard, B.J. Kennedy, P.M. Woodward, Ordered double perovskites - A group-theoretical analysis, Acta Crystallogr. B 59 (2003) 463–471. https://doi.org/10.1107/S0108768103010073.
  73. [74]P.W. Barnes, M.W. Lufaso, P.M. Woodward, Structure determination of A2M3+TaO6 and A2M3+NbO6 ordered perovskites: Octahedral tilting and pseudosymmetry, Acta Crystallogr. B 62 (2006) 384–396. https://doi.org/10.1107/S0108768106002448.
  74. [75]A.S. Oreshonkov, J. V. Gerasimova, A.A. Ershov, A.S. Krylov, K.A. Shaykhutdinov, A.N. Vtyurin, M.S. Molokeev, K.Y. Terent’Ev, N. V. Mihashenok, Raman spectra and phase composition of MnGeO3 crystals, Journal of Raman Spectroscopy 47 (2016) 531–536. https://doi.org/10.1002/JRS.4816.
  75. [76]T. Inagaki, K. Miura, H. Yoshida, J. Fujita, M. Nishimura, Raman studies of LaGaO3 and doped LaGaO3, Solid State Ion. 118 (1999) 265–269. https://doi.org/10.1016/S0167-2738(98)00350-6.
  76. [77]S. Adachi, Mn4+ vs Mn2+—A comparative study as efficient activator ions in phosphor materials: A review, J. Lumin. 263 (2023). https://doi.org/10.1016/J.JLUMIN.2023.119993.
  77. [78]M.G. Brik, S.J. Camardello, A.M. Srivastava, N.M. Avram, A. Suchocki, Spin-Forbidden Transitions in the Spectra of Transition Metal Ions and Nephelauxetic Effect, ECS Journal of Solid State Science and Technology 5 (2016) R3067–R3077. https://doi.org/10.1149/2.0091601JSS/XML.
  78. [79]J.G. Solé, L.E. Bausá, D. Jaque, Applications: Rare Earth and Transition Metal Ions, and Color Centers, An Introduction to the Optical Spectroscopy of Inorganic Solids (2005) 199–234. https://doi.org/10.1002/0470016043.CH6.
  79. [80]M. Grinberg, T. Lesniewski, S. Mahlik, R.S. Liu, 3d3 system – Comparison of Mn4+ and Cr3+ in different lattices, Opt. Mater. (Amst). 74 (2017) 93–100. https://doi.org/10.1016/J.OPTMAT.2017.03.057.

Paper details

vlnc:W_nyesjvcg
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents