betaFeedback

WorksMathematics

MPMICE: A hybrid MPM-CFD model for simulating coupled problems in porous media. Application to earthquake-induced submarine landslides

Abstract

In this paper, we describe a soil-fluid-structure interaction model that combines soil mechanics (saturated sediments), fluid mechanics (seawater or air), and solid mechanics (structures). The formulation combines the Material Point Method, which models large deformation of the porous media and the structure, with the Implicit Continuous-fluid Eulerian, which models complex fluid flows. We validate the model and simulate the whole process of earthquake-induced submarine landslides. We show that this model captures complex interactions between saturated sediment, seawater, and structure, so we can use the model to estimate the impact of potential submarine landslides on offshore structures.

Graphical Abstract

Graphical abstract showing the coupled soil-fluid-structure interaction model and its application to an earthquake-induced submarine landslide

Figure 20. Seawater, air (Fluid Mechanics); Sediment (Soil Mechanics); Porous Mechanics; Fluid-Structure Interaction; Contact Mechanics; Structure (Solid Mechanics); soil-fluid-structure interaction; Pore water pressure; Velocity; Shear strain; Application to earthquake-induced submarine landslide.

Highlights

MPMICE: A hybrid MPM-CFD model for simulating coupled problems in porous media. Application to earthquake-induced submarine landslides

Quoc Anh Tran, Gustav Grimstad, Seyed Ali Ghoreishian Amiri

  • MPMICE is introduced for multiphase flow in porous media.

  • Material Point method allows to model large deformation of non-isothermal porous media.

  • ICE (compressible multi-material CFD formulation) allows to stablize pore water pressure and turbulent flow.

  • MPMICE is validated and apply to simulate the earthquake-induced submarine landslide.

Nomenclature

General variables

VariableDimensionsDescription
VV[L3][L^3]Representative volume
nnPorosity
σ\sigma[ML−1t−2][M L^{-1} t^{-2}]Total stress tensor
Δt\Delta t[t][t]Time increment
b\mathbf{b}[MLt−2][M L t^{-2}]Body force
cvc_v[L2t−2T−1][L^2 t^{-2} T^{-1}]Constant volume specific heat
fdf_d[MLt−2][M L t^{-2}]Drag forces in momentum exchange term
fintf^{\mathrm{int}}[MLt−2][M L t^{-2}]Internal forces
fextf^{\mathrm{ext}}[MLt−2][M L t^{-2}]External forces
qfsq_{\mathrm{fs}}[MLt−2][M L t^{-2}]Heat exchange term
SSWeighting function
∇S\nabla SGradient of weighting function

Table 2.

Solid phase

VariableDimensionsDescription
msm_s[M][M]Solid mass
ρs\rho_s[ML−3][M L^{-3}]Solid density
ϕs\phi_sSolid volume fraction
ρˉs\bar{\rho}_s[ML−3][M L^{-3}]Bulk Solid density
xs\mathbf{x}_s[L][L]Solid Position vector
Us\mathbf{U}_s[Lt−1][L t^{-1}]Solid Velocity vector
as\mathbf{a}_s[Lt−2][L t^{-2}]Solid Acceleration vector
σ′\sigma'[ML−1t−2][M L^{-1} t^{-2}]Effective Stress tensor
ese_sStrain tensor
ese_s[L2t−2][L^2 t^{-2}]Solid Internal energy per unit mass
TsT_s[T][T]Solid Temperature
Fs\mathbf{F}_sSolid Deformation gradient
VsV_s[L3][L^3]Solid Volume

Table 3.

Fluid phase

VariableDimensionsDescription
mfm_f[M][M]Fluid mass
ρf\rho_f[ML−3][ML^{-3}]Fluid density
ϕf\phi_fFluid volume fraction
ρ‾f\overline{\rho}_f[ML−3][ML^{-3}]Bulk Fluid density
Uf\mathbf{U}_f[Lt−1][Lt^{-1}]Fluid Velocity vector
σf\boldsymbol{\sigma}_f[ML−1t−2][ML^{-1}t^{-2}]Fluid stress tensor
pfp_f[ML−1t−2][ML^{-1}t^{-2}]Fluid isotropic pressure
τf\boldsymbol{\tau}_f[ML−1t−2][ML^{-1}t^{-2}]Fluid shear stress tensor
efe_f[L2t−2][L^2t^{-2}]Fluid Internal energy per unit mass
TfT_f[T][T]Fluid Temperature
υf\upsilon_f[L3/M][L^3/M]Fluid Specific volume 1ρf\frac{1}{\rho_f}
αf\alpha_f[1/T][1/T]Thermal expansion
μ\mu[ML−1t−1][ML^{-1}t^{-1}]Fluid viscosity
VfV_f[L3][L^3]Fluid Volume

Table 4.

Superscript

VariableDimensionsDescription
nnCurrent time step
LLLagrangian values
n+1n+1Next time step

Table 5.

Subscript

VariableDimensionsDescription
ccCell-centered quantity
ppParticle quantity
iiNode quantity
FCFCFace-centered quantity
L,RL,RLeft and Right cell faces

Table 6.

Introduction

Many geological natural processes and their interactions with man-made structures are influenced by soil-fluid-structure interactions. The prediction of these processes requires a tool that can capture complex interactions between soil, fluid, and structure, such as the process of submarine landslides. Indeed, The offshore infrastructure as well as coastal communities may be vulnerable to submarine landslides. Submarine landslides contain three stages: triggering, failure, and post-failure. Erosion or earthquakes can trigger slope failures in the first stage. Following the failure, sediments move quickly after the post-failure stage. In other words, solid-like sediments will behave like a fluid after failure. This phase transition makes the simulation of submarine landslides a challeging task.

Due to this phase transition, submarine landslide can be modeled by either the Computational Fluid Dynamics (CFD) or the particle-based methods. For simulating submarine slides, CFD methods solve governing equations in a full-Eulerian framework [1, 2, 3, 4] with interface capturing techniques. While CFD can handle complex flows (such as turbulent flows), it cannot account for the triggering mechanism of submarine landslides because it is not straightforward to consider ’soil constitutive laws’ of sediment materials in the Eulerian framework. In contrast, particle-based methods can overcome this problem by using the Lagrangian framework. These methods have been extensively used to simulate landslides, like Material Point Method (MPM) [5], Smooth Particle Hydro Dynamics [6], Particle Finite Element Method [7], or Coupled Eulerian Lagrangian Method [8]. For simplicity, these simulations adopt total stress analysis which neglects the pore pressure development which is key factor triggering slope failures.

Recent developments in particle-based methods model the coupling of fluid flows in porous media by sets of Lagrangian particles. For the MPM family, it is the double-point MPM ([9, 10, 11]) where fluid particles and solid particles are overlapped in a single computational grid. Even if fluid flows are considered, particle-based methods have numerical instability in modeling the fluid flow, which requires additional numerical treatments such as the B-bar method [9], null-space filter [12], or least square approximation [13, 14]. Indeed, CFD is a more optimal option for complex fluid flows especially dealing with large distortions of continuum fluid media. Therefore, it could be ideal to combine the CFD with particle-based methods. More than 50 particle-based methods have been developed to solve large deformations of solids over the last two decades [15], but the MPM appears to be the best candidate for coupling with the CFD. Because MPM incorporates a stationary mesh during computation, just like CFD. As such, both MPM and CFD can be coupled naturally in a unified computational mesh.

A numerical method for simulating soil-fluid-structure interaction (Figure 1 (PDF p. 9)) involving large deformations, is presented in this work in order to simulate the interaction between sediment (soil), seawater (fluid) and offshore structures (structure) namely MPMICE (Figure 2). In the MPMICE, the Material Point Method (MPM) is coupled with the Implicit Continuous Eulerian (ICE). The MPM method is a particle method that allows the porous soil to undergo arbitrary distortions. The ICE method, on the other hand, is a conservative finite volume technique with all state variables located at the cell center (temperature, velocity, mass, pressure). An initial technical report [16] at Los Alamos National Laboratory provided the theoretical and algorithmic foundation for the MPMICE, followed by the MPMICE development and implementation in the high-performance Uintah computational framework for simulating fluid-structure interactions [17]. This paper primarily contributes further to the development of the MPMICE for analyzing the soil-fluid-structure interaction, since sediment should be considered as a porous media (soil) and not as a solid to capture the evolution of the pore water pressure. Baumgarten et al. [18] made the first attempt at coupling the Finite Volume Method with the MPM for the simulation of soil-fluid interaction. In contrast to the mentioned work, we use implicit time integration for the multi phase flows instead of explicit time integration for the single-phase flow.

Interaction between soil-fluid-structure

Figure 1 (PDF p. 9). Interaction between soil-fluid-structure

Coupling of soil-water-structure interaction using MPMICE

Figure 2. Coupling of soil-water-structure interaction using MPMICE

Theory and formulation

This section lay out the theoretical framework for the MPMICE model. We use the common notation of the continuum mechanics with vector and tensor denoted simply by using bold font and scalar denoted by using normal font. The notation are shown in Nomenclature.

Assumptions

The following assumptions are made for the MPMICE model.

  1. Solid phases (MPM) are described in a Lagrangian formulation while fluid phases (ICE) are described in an Eulerian formulation in the framework of continuum mechanics and mixture theory.

  2. Solid grains are incompressible while the fluid phases are compressible. Solid’s thermal expasion is negligible.

  3. There is no mass exchange between solid and fluid phases.

  4. Terzaghi’s effective stress is valid.

Governing equations

A representative element volume Ω\Omega is decomposed by two domains: solid domains Ωs\Omega_s and fluid domains Ωf\Omega_f. Then, all domains are homogenized into two overlapping continua. Considering the volume fraction of solid ϕs=Ωs/Ω\phi_s = \Omega_s/\Omega and fluid ϕf=Ωf/Ω\phi_f = \Omega_f/\Omega with the true (or Eulerian) porosity n=∑ϕfn = \sum\phi_f of the representative element volume, the average density of solid and fluid phases are defined as:

ρˉs=ϕsρs,ρˉf=ϕfρf(1)\bar{\rho}_s = \phi_s \rho_s,\qquad\bar{\rho}_f = \phi_f \rho_f \tag*{(1)}

The mass of solid and fluid phases are:

ms=∫ΩsρsdV=ρˉsV,mf=∫ΩfρfdV=ρˉfV(2)m_s = \int_{\Omega_s} \rho_s dV = \bar{\rho}_s V,\qquad m_f = \int_{\Omega_f} \rho_f dV = \bar{\rho}_f V \tag*{(2)}

Reviewing the Terzaghi’s effective stress concept for the saturated porous media, the total stress σ\boldsymbol{\sigma} is calculated by:

σ=σ′−pfI(3)\boldsymbol{\sigma} = \boldsymbol{\sigma}' - p_f \boldsymbol{I} \tag*{(3)}

The balance equations are derived based on the mixture theory. The representative thermodynamic state of the fluid phases are given by the vector [mf,Uf,ef,Tf,vf][m_f,U_f,e_f,T_f,v_f] which are mass, velocity, internal energy, temperature, specific volume. The representative state of the solid phases are given by the vector [ms,Us,es,Ts,σ′,pf][m_s,U_s,e_s,T_s,\boldsymbol{\sigma}',p_f] which are mass, velocity, internal energy, temperature, effective stress and pore water pressure. The derivation is presented in detail in the Appendix.

Mass Conservation

The mass balance equations for both fluid (e.g., water, air) and solid phases are:

1V∂mf∂t+∇⋅(mfUf)=0,1VDsmsDt=0(4)\frac{1}{V}\frac{\partial m_f}{\partial t}+\nabla\cdot(m_f\boldsymbol{U}_f)=0,\qquad\frac{1}{V}\frac{D_s m_s}{D t}=0 \tag*{(4)}

Solving the mass balance equation leads to:

DsnDt=ϕs∇⋅Us(5)\frac{D_s n}{D t}=\phi_s\nabla\cdot\boldsymbol{U}_s \tag*{(5)}

Momentum Conservation

The momentum balance equation for the fluid phases (e.g., water, air) are:

1V[∂(mfUf)∂t+∇⋅(mfUfUf)]=−ϕf∇pf+∇⋅τf+ρˉfb+∑fd(6)\frac{1}{V}\left[\frac{\partial(m_f\mathbf{U}_f)}{\partial t}+\nabla\cdot(m_f\mathbf{U}_f\mathbf{U}_f)\right]=-\phi_f\nabla p_f+\nabla\cdot\boldsymbol{\tau}_f+\bar{\rho}_f\mathbf{b}+\sum\mathbf{f}_d \tag*{(6)}

The momentum balance equation for the solid phases are:

1VDs(msUs)Dt=∇⋅σ′−ϕs∇pf+ρˉsb+∑ffric−∑fd(7)\frac{1}{V}\frac{D_s(m_s\mathbf{U}_s)}{Dt}=\nabla\cdot\boldsymbol{\sigma}'-\phi_s\nabla p_f+\bar{\rho}_s\mathbf{b}+\sum\mathbf{f}_{fric}-\sum\mathbf{f}_d \tag*{(7)}

Energy Conservation

The internal energy balance equation for the fluid phases (e.g., water, air) are:

1V[∂(mfef)∂t+∇⋅(mfefUf)]=−ρˉfpfDfυfDt+τf:∇Uf+∇⋅qf+∑qsf(8)\frac{1}{V}\left[\frac{\partial(m_f e_f)}{\partial t}+\nabla\cdot(m_f e_f\mathbf{U}_f)\right]=-\bar{\rho}_f p_f\frac{D_f\upsilon_f}{Dt}+\boldsymbol{\tau}_f:\nabla\mathbf{U}_f+\nabla\cdot\mathbf{q}_f+\sum q_{sf} \tag*{(8)}

The internal energy balance equation for the solid phase is:

msVcvDs(Ts)Dt=σ′:Ds(esp)Dt+∇⋅qs−∑qsf(9)\frac{m_s}{V}c_v\frac{D_s(T_s)}{Dt}=\boldsymbol{\sigma}':\frac{D_s(\mathbf{e}_s^p)}{Dt}+\nabla\cdot\mathbf{q}_s-\sum q_{sf} \tag*{(9)}

where cvc_v is the specific heat at constant volume of the solid materials.

Closing the systems of equations, the following additional models are needed:

  1. A constitutive equation to describe the stress - strain behaviour of solid phase (computing effective stress σ′\boldsymbol{\sigma}').

  2. Optional turbulent model to compute the viscous shear stress τf\boldsymbol{\tau}_f.

  3. Frictional forces ffric\mathbf{f}_{fric} for the contact for soil-structure interaction between solid/porous materials with the friction coefficient μfric\mu_{fric}.

  4. Exchange momentum models (computing drag force fd\mathbf{f}_d) for interaction between materials.

  5. Energy exchange models (computing temperature exhange term qsfq_{sf}) for interaction between materials.

  6. An equation of state to establish relations between thermodynamics variables of each fluid materials [pf,ρˉf,υf,Tf,ef][p_f,\bar{\rho}_f,\upsilon_f,T_f,e_f].

Four thermodynamic relations for the equation of states are:

ef=ef(Tf,vf)Pf=Pf(Tf,vf)ϕf=vfρˉf0=n−∑f=1Nfvfρˉf(10)\begin{aligned} e_f &= e_f(T_f,v_f) \\ P_f &= P_f(T_f,v_f) \\ \phi_f &= v_f\bar{\rho}_f \\ 0 &= n-\sum_{f=1}^{N_f}v_f\bar{\rho}_f \tag*{(10)} \end{aligned}

Constitutive soil model

As a result of the explicit MPM formulation, we can derive the constitutive law in the updated Lagrangian framework of ”small strain - large deformation”. Therefore, the rotation of the particles (representative element volume) is manipulated by rotating the Cauchy stress tensor. First, the deformation gradient is decomposed into the polar rotation tensor Rsn+1\mathbf{R}_s^{n+1} and sketch tensor Vsn+1\mathbf{V}_s^{n+1} as

Fsn+1=Vsn+1Rsn+1(11)\mathbf{F}_s^{n+1}=\mathbf{V}_s^{n+1}\mathbf{R}_s^{n+1} \tag*{(11)}

Then, before calling the constitutive model, the stress and strain rate tensor are rotated to the reference configuration as

σ′,n∗=(Rsn+1)Tσ′,n∗Rsn+1(12)\boldsymbol{\sigma}^{\prime,n*}=\left(\mathbf{R}_s^{n+1}\right)^{T}\boldsymbol{\sigma}^{\prime,n*}\mathbf{R}_s^{n+1} \tag*{(12)}
δϵn∗=(Rsn+1)Tδϵn∗Rsn+1(13)\delta\boldsymbol{\epsilon}^{n*}=\left(\mathbf{R}_s^{n+1}\right)^{T}\delta\boldsymbol{\epsilon}^{n*}\mathbf{R}_s^{n+1} \tag*{(13)}

Using the constitutive model with the input tensors σ′,n∗\boldsymbol{\sigma}^{\prime,n*}, δϵn∗\delta\boldsymbol{\epsilon}^{n*} to compute the Cauchy stress tensor at the advanced time step σ′,n+1∗\boldsymbol{\sigma}^{\prime,n+1*} then rotating it back to current configuration

σ′,n+1=Rsn+1σ′,n+1∗(Rsn+1)T(14)\boldsymbol{\sigma}^{\prime,n+1}=\mathbf{R}_s^{n+1}\boldsymbol{\sigma}^{\prime,n+1*}\left(\mathbf{R}_s^{n+1}\right)^{T} \tag*{(14)}

In this paper, we adopt the hyper-elastic Neo Hooken model for the structure materials and additionally Mohr-Coulomb failure criteria for the soil (porous media) materials. The Cauchy stress of the hyper-elastic Neo Hookean model can be written as:

σ′=λln⁡(J)J+μJ(FFT−J)(15)\boldsymbol{\sigma}'=\frac{\lambda\ln(J)}{J}+\frac{\mu}{J}\left(\mathbf{F}\mathbf{F}^{T}-J\right) \tag*{(15)}

where λ\lambda and μ\mu are bulk and shear modulus ad J is the determinant of the deformation gradient F\mathbf{F}. And the yield function f and flow potentials g of the Mohr-Coulomb can be written as:

f=σ1′−σ3′−2c′cos⁡(ϕ′)−(σ1′+σ3′)sin⁡(ϕ′)g=σ1′−σ3′−2c′cos⁡(ψ′)−(σ1′+σ3′)sin⁡(ψ′)(16)\begin{aligned} f &= \sigma'_1-\sigma'_3-2c'\cos(\phi')-(\sigma'_1+\sigma'_3)\sin(\phi')\\ g &= \sigma'_1-\sigma'_3-2c'\cos(\psi')-(\sigma'_1+\sigma'_3)\sin(\psi') \tag*{(16)} \end{aligned}

where the c′c', ϕ′\phi' and ψ′\psi' are cohesion and friction angle and dilation angle. σ1′\sigma'_1 and σ3′\sigma'_3 are maximum and minimum principal stress.

Turbulent model

The turbulent effect is modelled using a statistical approach namely large-eddy simulation. In this approach, the micro-scale turbulent influence in the dynamics of the macro-scale motion is computed through simple models like Smagorinsky model. In the Smagorinsky mode, the residual stress tensor is:

τij=2μeff(S‾ij−13δijS‾kk)+13δijτkk(17)\tau_{ij}=2\mu_{eff}\left(\overline{S}_{ij}-\frac{1}{3}\delta_{ij}\overline{S}_{kk}\right)+\frac{1}{3}\delta_{ij}\tau_{kk} \tag*{(17)}

where the the strain rate tensor is given by

S‾ij=12(∂U‾i∂xj+∂U‾j∂xi)(18)\overline{S}_{ij}=\frac{1}{2}\left(\frac{\partial\overline{U}_i}{\partial x_j}+\frac{\partial\overline{U}_j}{\partial x_i}\right) \tag*{(18)}

and the effective viscosity is sum of molecular viscosity and turbulent viscosity μeff=μ+μt\mu_{eff}=\mu+\mu_t in which the turbulent viscosity μt\mu_t is calculated by

μt=(CsΔ)22S‾ijS‾ij(19)\mu_t=(C_s\Delta)^2\sqrt{2\overline{S}_{ij}\overline{S}_{ij}} \tag*{(19)}

where CsC_s is the Smagorinsky constant and Δ=dxdydz3\Delta=\sqrt[3]{dxdydz} is the grid size that defines the subgrid length scale.

Frictional force for soil-structure interaction

MPMICE includes a contactlaw for the interaction between soil and structure using the first Coulomb friction contact for MPM presented by Bardenhagen et al. [19]. The magnitude of the friction force at the contact depends on the friction coefficient μfric\mu_{fric} and the normal force fnorm\mathbf{f}_{norm} computed from the projection of the contact force in the normal direction.

ffric=μfricfnorm(20)\mathbf{f}_{fric}=\mu_{fric}\mathbf{f}_{norm} \tag*{(20)}

The contact determines whether the soil is sliding or sticking to the structure by comparing the friction force with the sticking force fstickf_{stick} computed from the projection of the contact force in the tangent direction:

if ffric≥fstick no slidingif ffric<fstick sliding occurs(21)\begin{aligned} &\text{if } f_{fric} \ge f_{stick}\ \text{no sliding}\\ &\text{if } f_{fric} < f_{stick}\ \text{sliding occurs} \tag*{(21)} \end{aligned}

Frictional sliding between solid materials also generates dissipation and the work rate generated from the sliding can be calculated as:

ΔWfriction=ffricd(22)\Delta W_{friction} = f_{fric}d \tag*{(22)}

where d is the sliding distance which can computed based on the sliding velocity between two materials.

Momentum and Energy exchange model

Currently, the energy exchange coefficient HsfH_{sf} is assumed to be constant for the sake of simplicity. Then the energy exchange can be written as:

qsf=Hsf(Tf−Ts)(23)q_{sf} = H_{sf}(T_f-T_s) \tag*{(23)}

On the other hand, the drag force can be calculated as:

fd=K(Us−Uf)(24)f_d = K(U_s-U_f) \tag*{(24)}

For the momentum exchange between fluid flows and porous media, we assume that the drag force fdf_d depends on the average grain size of the grains DpD_p, the porosity nn, the fluid viscosity μf\mu_f, and is proportional to the relative velocities of soil grains and fluid (Us−Uf)(U_s-U_f). Based on recent investigation of CFD simulations of fluid flow around mono- and bi-disperse packing of spheres for 0.1<ϕs<0.60.1 < \phi_s < 0.6 and Re<1000Re < 1000 [20]. The drag force is given by:

fd=18ϕs(1−ϕs)μfDp2F(ϕs,Re)(Us−Uf)(25)f_d = \frac{18\phi_s(1-\phi_s)\mu_f}{D_p^2}F(\phi_s,Re)(U_s-U_f) \tag*{(25)}

where Reynolds number ReRe are computed as:

Re=nρfDpμf∥(Us−Uf)∥(26)Re = \frac{n\rho_fD_p}{\mu_f}\lVert(U_s-U_f)\rVert \tag*{(26)}

The function F(ϕs,Re)F(\phi_s, Re) can be calculated as:

F(ϕs,Re)=F(ϕs,0)+0.413Re24(1−ϕs)2((1−ϕs)−1+3ϕs(1−ϕs)+8.4Re−0.3431+103ϕsRe−(1+4ϕs)/2)(27)F(\phi_s, Re) = F(\phi_s, 0) + \frac{0.413Re}{24(1-\phi_s)^2}\left(\frac{(1-\phi_s)^{-1} + 3\phi_s(1-\phi_s) + 8.4Re^{-0.343}}{1 + 10^{3\phi_s}Re^{-(1+4\phi_s)/2}}\right) \tag*{(27)}

where the low Reynold coefficient F(ϕs,Re→0)F(\phi_s, Re \to0) is:

F(ϕs,0)=10ϕs(1−ϕs)2+(1−ϕs)2(1+1.5ϕs)(28)F(\phi_s, 0) = \frac{10\phi_s}{(1-\phi_s)^2} + (1-\phi_s)^2(1 + 1.5\sqrt{\phi_s}) \tag*{(28)}

When validating the model with analytical solution, it requires to know the hydraulic conductivity. In such case, we convert the equation (25) to Kozeny-Carman formula by assuming F(ϕs,Re)=10ϕs/(1−ϕs)2F(\phi_s, Re) = 10\phi_s/(1-\phi_s)^2, then the hydraulic conductivity will be expressed as Dp2(1−ϕs)3/180μϕs2D_p^2(1-\phi_s)^3/180\mu\phi_s^2.

Solving momentum and energy exchange with an implicit solver

The derivation of the implicit integration for the momentum exchange is presented in the Appendix’s section ’Momentum and energy exchange with an implicit solver’. The linear equations for multi phases i,j=1:N has the form:

∣1+βij−βij−βji1+βji∣∣ΔUiΔUj∣=∣βij(Ui∗−Uj∗)βji(Ui∗−Uj∗)∣\begin{vmatrix} 1+\beta_{ij} & -\beta_{ij} \\ -\beta_{ji} & 1+\beta_{ji} \end{vmatrix} \begin{vmatrix} \Delta U_i \\ \Delta U_j \end{vmatrix} = \begin{vmatrix} \beta_{ij}(U_i^* - U_j^*) \\ \beta_{ji}(U_i^* - U_j^*) \end{vmatrix}

where the intermediate velocity for fluid phases f=1:Nf\mathrm{f}=1:N_f and for solid/porous phases s=1:Ns\mathrm{s}=1:N_s can be calculated by

Uf∗=Ufn+Δt(−∇Pfn+1ρfn+∇⋅τfnρfn+b)Us∗=Usn+Δt(∇⋅σsnρˉsn−∇Pfn+1ρs+b)(29)\begin{aligned} U_f^* &= U_f^n + \Delta t\left(-\frac{\nabla P_f^{n+1}}{\rho_f^n} + \frac{\nabla\cdot\boldsymbol{\tau}_f^n}{\rho_f^n} + b\right) \\ U_s^* &= U_s^n + \Delta t\left(\frac{\nabla\cdot\boldsymbol{\sigma}_s^n}{\bar{\rho}_s^n} - \frac{\nabla P_f^{n+1}}{\rho_s} + b\right) \tag*{(29)} \end{aligned}

Also, the momentum exchange coefficient can be computed at every time step as β12=K/ρˉfn\beta_{12}=K/\bar{\rho}_f^n and β21=K/ρˉsn\beta_{21}=K/\bar{\rho}_s^n with the coefficient depending on the different type of interactions (see Figure 3) as for example:

Momentum exchange coefficient between materials

Figure 3. Momentum exchange coefficient between materials

  1. The drag force is set to zero in soil-structure interactions, and instead the frictional force is computed.

  2. As a result of fluid-structure interaction, the momentum exchange coefficient should be extremely high when the solid material points are considered to be zero-porosity/zero-permeability.

  3. In the case of soil-fluid interaction, the drag force is calculated using the equation (25). Considering that air has a much lower viscosity than water, its drag force is much lower than the drag force of water in a pore.

  4. A momentum exchange coefficient of 1E5 is applied between multiphase flows. This value is far higher than reality [21], but it is necessary to have enough numerical stability to conduct simulations in the numerical example.

Similar approach applied for the energy exchange term leading to:

∣1+ηij−ηij−ηij1+ηij∣∣ΔTiΔTj∣=∣ηij(Tin−Tjn)ηij(Tjn−Tin)∣\begin{vmatrix} 1+\eta_{ij} & -\eta_{ij} \\ -\eta_{ij} & 1+\eta_{ij} \end{vmatrix} \begin{vmatrix} \Delta T_i \\ \Delta T_j \end{vmatrix} = \begin{vmatrix} \eta_{ij}(T_i^n-T_j^n) \\ \eta_{ij}(T_j^n-T_i^n) \end{vmatrix}

with η\eta is the energy exchange coefficient.

Equation of state for fluid plases

The equation of state establishes relations between thermodynamics variables [Pf,ρf,Tf][P_f,\rho_f,T_f]. The choice of the equation of state depends on the types of the fluid materials. For example, for the air, it is possible to assume the equation of state for the perfect gas which obeys:

Pf=ρfRTf(30)P_f=\rho_fRT_f \tag*{(30)}

where RR is the gas constant. For the water, a simple linear equation of state is in the following form:

Pf=Pref+Kf(ρf−ρref−αf(Tf−Tref))(31)P_f=P_{\mathrm{ref}}+K_f(\rho_f-\rho_{\mathrm{ref}}-\alpha_f(T_f-T_{\mathrm{ref}})) \tag*{(31)}

where reference pressure Pref=1 atm=101325 PaP_{\mathrm{ref}=1\ \mathrm{atm}=101325\ \mathrm{Pa}}, reference temperature Tref=10∘CT_{\mathrm{ref}}=10^\circ\mathrm{C}, reference density ρref=999.8 kg/m3\rho_{\mathrm{ref}}=999.8\ \mathrm{kg/m^3}, the bulk modulus of water Kf=2 GPaK_f=2\ \mathrm{GPa}, and the water thermal expansion αf=0.18 ∘C−1\alpha_f=0.18\ ^\circ\mathrm{C}^{-1}. Equation (31) matches well with the state of the water (see Figure 4).

Density versus temperature for water at different pressures

Figure 4. Equation of state of water

Numerical implementation

The fluid phases are discretized in the grid with the state variables stored at the centroid of the cells [ρfc,Ufc,Tfc,υfc][\rho_{fc}, \mathbf{U}_{fc}, T_{fc}, \boldsymbol{\upsilon}_{fc}] while the solid phase is discretized in the particles with the state variables [msp,Usp,Tsp,σsp′][m_{sp}, \mathbf{U}_{sp}, T_{sp}, \boldsymbol{\sigma}'_{sp}]. In the Material Point Method, we use the generalized interpolation technique [22] using the weight function as a convolution of a grid shape function Ni(x)N_i(\mathbf{x}) in a nodal domain Ωi\Omega_i and a characteristic function χp(x)\chi_p(\mathbf{x}) in a particle domain Ωp\Omega_p with the volume Vp(x)V_p(\mathbf{x}) as follows:

Sip=1Vp∫Ωi∩ΩpNi(x)χp(x) dx(32)S_{ip} = \frac{1}{V_p} \int_{\Omega_i \cap\Omega_p} N_i(\mathbf{x})\chi_p(\mathbf{x})\,\mathrm{d}x \tag*{(32)}

where the volume Vp(x)V_p(\mathbf{x}) of the material point p can be calculated as:

Vp=∫Ωpχp(x) dx(33)V_p = \int_{\Omega_p} \chi_p(\mathbf{x})\,\mathrm{d}x \tag*{(33)}

The charateristic function is the Heaviside function as χp=1\chi_p = 1 if x∈Ωpx \in\Omega_p, otherwise 0 (see Figure 5). For the interpolation of the centroid of the cell, the linear basis function is used as:

GIMP weighting function showing the convolution of a linear basis shape function and a characteristic function

Figure 5. GIMP weighting function (red as a convolution of the linear basis shape function (green) and the charateristic function (blue)

Sci=Ni(xc)(34)S_{ci} = N_i(x_c) \tag*{(34)}

The time discretization are solved using the following steps:

Interpolation from Solid Particle to Grid

The nodal values of the solid state (mass, velocity, temperature, volume) are:

msin=∑SipmspUsin=∑Sip(mU)spnmsinTsin=∑Sip(mT)spnmsinVsin=∑Sip(mV)spnmsinσsin=∑Sip(σV)spnVsin(35)\begin{aligned} m_{si}^{n} &= \sum S_{ip}m_{sp} \\ U_{si}^{n} &= \frac{\sum S_{ip}(mU)_{sp}^{n}}{m_{si}^{n}} \\ T_{si}^{n} &= \frac{\sum S_{ip}(mT)_{sp}^{n}}{m_{si}^{n}} \\ V_{si}^{n} &= \frac{\sum S_{ip}(mV)_{sp}^{n}}{m_{si}^{n}} \\ \boldsymbol{\sigma}_{si}^{n} &= \frac{\sum S_{ip}(\boldsymbol{\sigma}V)_{sp}^{n}}{V_{si}^{n}} \tag*{(35)} \end{aligned}

The nodal internal forces is calculated by

fsiint,n=−∑∇Sip(σsp′)nVspn(36)f_{si}^{int,n} = -\sum\nabla S_{ip}(\sigma'_{sp})^{n}V_{sp}^{n} \tag*{(36)}

The nodal external forces fsiext,nf_{si}^{ext,n} and extra momentum from contact forces are computed here. The nodal velocity and nodal temperature are applied boundary conditions. Then we compute the solid cell variables as:

mscn=∑Scimsiρscn=mscnVUscn=∑SciUsinTscn=∑SciTsinVscn=∑SciVsinσscn=∑Sciσsin(37)\begin{aligned} m_{sc}^{n} &= \sum S_{ci}m_{si} \\ \rho_{sc}^{n} &= \frac{m_{sc}^{n}}{V} \\ U_{sc}^{n} &= \sum S_{ci}U_{si}^{n} \\ T_{sc}^{n} &= \sum S_{ci}T_{si}^{n} \\ V_{sc}^{n} &= \sum S_{ci}V_{si}^{n} \\ \boldsymbol{\sigma}_{sc}^{n} &= \sum S_{ci}\boldsymbol{\sigma}_{si}^{n} \tag*{(37)} \end{aligned}

Compute equation of state for fluid phase

Considering the total fluid material volume of a cell is:

Vtotal=∑f=1NfMfvf(38)V_{total}=\sum_{f=1}^{N_f} M_f v_f \tag*{(38)}

Then we need to find PeqP_{eq} which allows each fluid materials obey their equation of states [Pf,ρf,vf,Tf,ef][P_f,\rho_f,v_f,T_f,e_f] but also allow mass of all fluid materials to fill the entire the pore volume without ongoing compression or expansion following the condition:

0=n−∑f=1Nfvˉfρf(39)0=n-\sum_{f=1}^{N_f}\bar{v}_f\rho_f \tag*{(39)}

Then, we can use the Newton-Raphson iteration to find the value of PeqP_{eq} which satisfies the equation (38, 39) and each equation of states of each fluid materials.

Compute faced-centered velocity

Following the derivation in the Appendix: Advanced Fluid Pressure, we first compute the fluid face-centered velocity as

Uf,FC∗n=(ρU‾)f,FCnρ‾f,FCn+Δt(−∇FCPeqρ‾f,FCn+∇FC⋅τnρ‾s,FC+b)(40)U^{*n}_{f,FC}=\frac{(\overline{\rho U})^n_{f,FC}}{\overline{\rho}^n_{f,FC}}+\Delta t\left(-\frac{\nabla^{FC}P_{eq}}{\overline{\rho}^n_{f,FC}}+\frac{\nabla^{FC}\cdot\boldsymbol{\tau}^n}{\overline{\rho}_{s,FC}}+b\right) \tag*{(40)}

The equation (40) is discretized in three dimension (noted that ∇FC⋅τ=0\nabla^{FC}\cdot\boldsymbol{\tau}=0), for example the discretized equation in the x direction is

Ufx∗n=(ρU‾)fx,Rn+(ρU‾)fx,Lnρ‾fx,Ln+ρ‾fx,Rn+Δt(−2(vfx,Lnvfx,Rn)vfx,Ln+vfx,RnPeqx,R−Peqx,LΔx+bx)(41)U^{*n}_{fx}=\frac{(\overline{\rho U})^n_{fx,R}+(\overline{\rho U})^n_{fx,L}}{\overline{\rho}^n_{fx,L}+\overline{\rho}^n_{fx,R}}+\Delta t\left(-\frac{2(v^n_{fx,L}v^n_{fx,R})}{v^n_{fx,L}+v^n_{fx,R}}\frac{P_{eqx,R}-P_{eqx,L}}{\Delta x}+b_x\right) \tag*{(41)}

The face-centered solid velocity can be calculated as

Us,FC∗n=(ρU‾)s,FCnρ‾s,FCn+Δt(∇FC⋅σc′nρ‾s,FC−∇FCPeqρs+b)(42)U^{*n}_{s,FC}=\frac{(\overline{\rho U})^n_{s,FC}}{\overline{\rho}^n_{s,FC}}+\Delta t\left(\frac{\nabla^{FC}\cdot\boldsymbol{\sigma}'^{n}_{c}}{\overline{\rho}_{s,FC}}-\frac{\nabla^{FC}P_{eq}}{\rho_s}+b\right) \tag*{(42)}

The equation (42) is discretized in three dimension(noted that ∇FC⋅σij=0\nabla^{FC}\cdot\sigma_{ij}=0 with i≠ji\ne j), for example the discretized equation in the x direction is

Usx∗n=(ρU‾)sx,Rn+(ρU‾)sx,Lnρ‾sx,Ln+ρ‾sx,Rn+Δt(2(σxx,R−σxx,L)(ρ‾sx,Ln+ρ‾sx,Rn)Δx−Peqx,R−Peqx,LρsΔx+bx)(43)U^{*n}_{sx}=\frac{(\overline{\rho U})^n_{sx,R}+(\overline{\rho U})^n_{sx,L}}{\overline{\rho}^n_{sx,L}+\overline{\rho}^n_{sx,R}}+\Delta t\left(\frac{2(\sigma_{xx,R}-\sigma_{xx,L})}{(\overline{\rho}^n_{sx,L}+\overline{\rho}^n_{sx,R})\Delta x}-\frac{P_{eqx,R}-P_{eqx,L}}{\rho_s\Delta x}+b_x\right) \tag*{(43)}

Computing the modified faced-centered velocity UFCLU^{L}_{FC} considering the momentum exchange (see the Appendix: Momentum exchange with an implicit solve)

Uf,FCL=Uf,FC∗+ΔUf,FCUs,FCL=Us,FC∗+ΔUs,FC(44)\begin{aligned} U^{L}_{f,FC} &= U^{*}_{f,FC}+\Delta U_{f,FC}\\ U^{L}_{s,FC} &= U^{*}_{s,FC}+\Delta U_{s,FC} \tag*{(44)} \end{aligned}

Solving the linear equation below to obtain the increment of velocity with i,j = 1 : NN as:

∣1+βij−βij−βji1+βji∣∣ΔUi,FCΔUj,FC∣=∣βij(Ui,FC∗−Uj,FC∗)βji(Uj,FC∗−Ui,FC∗)∣\begin{vmatrix} 1+\beta_{ij} & -\beta_{ij}\\ -\beta_{ji} & 1+\beta_{ji} \end{vmatrix} \begin{vmatrix} \Delta U_{i,FC}\\ \Delta U_{j,FC} \end{vmatrix} = \begin{vmatrix} \beta_{ij}(U^{*}_{i,FC}-U^{*}_{j,FC})\\ \beta_{ji}(U^{*}_{j,FC}-U^{*}_{i,FC}) \end{vmatrix}

Compute faced-centered temperature

Similar to the velocity, the faced temperature is computed as:

Tfxn=(ρT‾)fx,Rn+(ρT‾)fx,Lnρfx,Ln+ρfx,Rn(45)T^{n}_{fx}=\frac{(\overline{\rho T})^{n}_{fx,R}+(\overline{\rho T})^{n}_{fx,L}}{\rho^{n}_{fx,L}+\rho^{n}_{fx,R}} \tag*{(45)}

Computing the modified faced-centered temperature TFCLT^{L}_{FC} considering the energy exchange (see the Appendix: Momentum and energy exchange with an implicit solver)

Tf,FCL=Tf,FCn+ΔTf,FCTs,FCL=Ts,FCn+ΔTs,FC(46)\begin{aligned} T^{L}_{f,FC} &= T^{n}_{f,FC}+\Delta T_{f,FC}\\ T^{L}_{s,FC} &= T^{n}_{s,FC}+\Delta T_{s,FC} \tag*{(46)} \end{aligned}

Solving the linear equation below to obtain the increment of velocity with i,j = 1 : NN as:

∣1+ηij−ηij−ηji1+ηji∣∣ΔTi,FCΔTj,FC∣=∣ηij(Ti,FCn−Tj,FCn)ηji(Tj,FCn−Ti,FCn)∣\begin{vmatrix} 1+\eta_{ij} & -\eta_{ij}\\ -\eta_{ji} & 1+\eta_{ji} \end{vmatrix} \begin{vmatrix} \Delta T_{i,FC}\\ \Delta T_{j,FC} \end{vmatrix} = \begin{vmatrix} \eta_{ij}(T^{n}_{i,FC}-T^{n}_{j,FC})\\ \eta_{ji}(T^{n}_{j,FC}-T^{n}_{i,FC}) \end{vmatrix}

Compute fluid pressure (implicit scheme)

For single phase flow, the increment of the fluid pressure can be computed as:

κfΔPdt=∇c⋅Uf,FCn+1(47)\kappa_{f}\frac{\Delta P}{dt}=\nabla^{c}\cdot U^{n+1}_{f,FC} \tag*{(47)}

For multi-phase flows, the increment of the fluid pressure of the mixture can be computed as:

κΔPdt=∑f=1Nf∇c⋅(ϕf,FCUf,FC)n+1(48)\kappa\frac{\Delta P}{dt}=\sum_{f=1}^{N_{f}}\nabla^{c}\cdot\left(\phi_{f,FC}U_{f,FC}\right)^{n+1} \tag*{(48)}

where κ=∑f=1Nf(ϕf,FCκf)/∑f=1Nf(ϕf,FC)\kappa= \sum_{f=1}^{N_f}(\phi_{f,FC}\kappa_f)/\sum_{f=1}^{N_f}(\phi_{f,FC}). Then, the fluid pressure at cell center is:

Pcn+1=Peq+ΔPcn(49)P_c^{n+1}=P_{eq}+\Delta P_c^n \tag*{(49)}

Finally, the faced-centered advanced fluid pressure is

PFCn+1=(Pc,Ln+1ρf,Ln+Pc,Rn+1ρf,Rn)(1ρf,Ln+1ρf,Rn)−1=(Pc,Ln+1ρf,Rn+Pc,Rn+1ρf,Lnρf,Lnρf,Rn)(50)P_{FC}^{n+1}=\left(\frac{P_{c,L}^{n+1}}{\rho_{f,L}^n}+\frac{P_{c,R}^{n+1}}{\rho_{f,R}^n}\right)\left(\frac{1}{\rho_{f,L}^n}+\frac{1}{\rho_{f,R}^n}\right)^{-1}=\left(\frac{P_{c,L}^{n+1}\rho_{f,R}^n+P_{c,R}^{n+1}\rho_{f,L}^n}{\rho_{f,L}^n\rho_{f,R}^n}\right) \tag*{(50)}

Compute viscous shear stress term of the fluid phase

This part compute the viscous shear stress Δ(mU)fc,τ\Delta(mU)_{f c,\tau} for a single vicous compressible Newtonian fluid and optionally shear stress induced by the turbulent model.

Compute nodal internal temperature of the solid phase

The nodal internal temperature rate is computed based on the heat conduction model

dTsiL=ΔWsin+ΔWfric,in+∇i⋅qsinmsincv(51)dT_{si}^{L}=\frac{\Delta W_{si}^n+\Delta W_{fric,i}^n+\nabla^i\cdot\mathbf{q}_{si}^n}{m_{si}^n c_v} \tag*{(51)}

where ΔWsin=σ′:Ds(εsp)Dt\Delta W_{si}^n=\sigma':\frac{D_s(\varepsilon_s^p)}{Dt} is the mechanical work rate computed from the constitutive model with εsp\varepsilon_s^p is the plastic strain, ΔWfric,in\Delta W_{fric,i}^n is the work rate compted from the contact law due to the frictional sliding between solid materials. The heat flux is qs=ρˉsβs∇Ts\mathbf{q}_s=\bar{\rho}_s\beta_s\nabla T_s with βs\beta_s being the thermal conductivity of the solid materials.

TsiL=Tsin+dTsiL(52)T_{si}^{L}=T_{si}^n+dT_{si}^{L} \tag*{(52)}

Compute and integrate acceleration of the solid phase

After interpolating from material points to the nodes, the nodal acceleration and velocity are calculate by

asiL=fsiint,n+fsiext,nmsin+g(53)\mathbf{a}_{si}^{L}=\frac{\mathbf{f}_{si}^{int,n}+\mathbf{f}_{si}^{ext,n}}{m_{si}^n}+\mathbf{g} \tag*{(53)}
UsiL=Usin+asiLΔt(54)\mathbf{U}_{si}^{L}=\mathbf{U}_{si}^n+\mathbf{a}_{si}^{L}\Delta t \tag*{(54)}

Compute Lagrangian value (mass, momentum and energy)

For the fluid phase, the linear momentum rate, the energy rate are

Δ(mU)fc=Vncn∇cPcn+1+Δ(mU)fc,τ+Vρˉfcng(55)\Delta(mU)_{fc}=Vn_c^n\nabla^cP_c^{n+1}+\Delta(mU)_{fc,\tau}+V\bar{\rho}_{fc}^n g \tag*{(55)}
Δ(me)fc=VncnPcn+1∇c⋅Uf,FC∗+∇c⋅qfcn(56)\Delta(me)_{fc}=Vn_c^nP_c^{n+1}\nabla^c\cdot U^*_{f,FC}+\nabla^c\cdot q_{fc}^n \tag*{(56)}

The Lagrangian value of the mass, linear momentum and energy of fluid phases without momentum exchange are

mfcL=Vρˉfcn(57)m_{fc}^{L}=V\bar{\rho}_{fc}^n \tag*{(57)}
(mU)fcL=VρˉfcnUfcn+Δ(mU)fc(58)(mU)_{fc}^{L}=V\bar{\rho}_{fc}^nU_{fc}^n+\Delta(mU)_{fc} \tag*{(58)}
(me)fcL=VρˉfcnTfcncv+Δ(me)fc(59)(me)_{fc}^{L}=V\bar{\rho}_{fc}^nT_{fc}^nc_v+\Delta(me)_{fc} \tag*{(59)}

For the solid phase, the Lagrangian value of the linear momentum and energy of solid phase are

mscL=mscn(60)m_{sc}^{L}=m_{sc}^n \tag*{(60)}
(mU)scL=∑ScimsinUsiL−+V(1−ncn)∇cPfcn+1(61)(mU)_{sc}^{L}=\sum S_{ci}m_{si}^nU_{si}^{L-}+V(1-n_c^n)\nabla^cP_{fc}^{n+1} \tag*{(61)}
(me)scL=∑ScimsinTsiLcv(62)(me)_{sc}^{L}=\sum S_{ci}m_{si}^nT_{si}^{L}c_v \tag*{(62)}

To consider the momentum exchange, the Lagrangian velocity is modified as

UfcL=UfcL−+ΔUfcU_{fc}^{L}=U_{fc}^{L-}+\Delta U_{fc}
UscL=UscL−+ΔUsc(63)U_{sc}^{L}=U_{sc}^{L-}+\Delta U_{sc} \tag*{(63)}

where the cell-centered intermediate velocity can be calculated by

UfcL−=(mU)fcL−mfcLU_{fc}^{L-}=\frac{(mU)_{fc}^{L-}}{m_{fc}^{L}}
UscL−=(mU)scL−mscL(64)U_{sc}^{L-}=\frac{(mU)_{sc}^{L-}}{m_{sc}^{L}} \tag*{(64)}

And the increment of the velocity UfcU_{fc}, ΔUsc\Delta U_{sc} can be computed by solving the linear equation with i,j = 1 : NN as:

∣1+βij−βij−βji1+βji∣∣ΔUi,cΔUj,c∣=∣βij(Ui,c∗−Uj,c∗)βji(Uj,c∗−Ui,c∗)∣\begin{vmatrix} 1+\beta_{ij} & -\beta_{ij}\\ -\beta_{ji} & 1+\beta_{ji} \end{vmatrix} \begin{vmatrix} \Delta U_{i,c}\\ \Delta U_{j,c} \end{vmatrix} = \begin{vmatrix} \beta_{ij}(U^*_{i,c}-U^*_{j,c})\\ \beta_{ji}(U^*_{j,c}-U^*_{i,c}) \end{vmatrix}

To consider the energy exchange, the Lagrangian temperature is modified as

TfcL=TfcL−+ΔTfcTscL=TscL−+ΔTsc(65)\begin{aligned} T_{fc}^{L} &= T_{fc}^{L-} + \Delta T_{fc}\\ T_{sc}^{L} &= T_{sc}^{L-} + \Delta T_{sc} \tag*{(65)} \end{aligned}

where the cell-centered intermediate temperature can be calculated by

TfcL−=(mT)fcL−mfcL−cvTscL−=(mT)scL−mscL−cv(66)\begin{aligned} T_{fc}^{L-} &= \frac{(mT)_{fc}^{L-}}{m_{fc}^{L-}c_v}\\ T_{sc}^{L-} &= \frac{(mT)_{sc}^{L-}}{m_{sc}^{L-}c_v} \tag*{(66)} \end{aligned}

And the increment of the velocity can be computed by solving the linear equation with i,j=1:Ni,j = 1 : N as:

∣(1+ηij)−ηij−ηji(1+ηji)∣(ΔTi,cΔTj,c)=(ηij(Ti,cn−Tj,cn)ηji(Tj,cn−Ti,cn))\left| \begin{array}{cc} (1+\eta_{ij}) & -\eta_{ij}\\ -\eta_{ji} & (1+\eta_{ji}) \end{array} \right| \begin{pmatrix} \Delta T_{i,c}\\ \Delta T_{j,c} \end{pmatrix} = \begin{pmatrix} \eta_{ij}(T_{i,c}^{n}-T_{j,c}^{n})\\ \eta_{ji}(T_{j,c}^{n}-T_{i,c}^{n}) \end{pmatrix}

Finally, we obtain the cell-centered solid acceleration and temperature rate as

dUscL=(mU)scL−(mU)scnmscLΔt(67)dU_{sc}^{L} = \frac{(mU)_{sc}^{L}-(mU)_{sc}^{n}}{m_{sc}^{L}\Delta t} \tag*{(67)}
dTscL=(me)scL−(me)scnmscLcvΔt(68)dT_{sc}^{L} = \frac{(me)_{sc}^{L}-(me)_{sc}^{n}}{m_{sc}^{L}c_v\Delta t} \tag*{(68)}

Compute Lagrangian specific volume of the fluid phase

To compute the Lagrangian value of the specific volume of the fluid phase, we need to compute the Lagrangian temperature rate as below

Tfcn+1=(me)fcLmfcLcv(69)T_{fc}^{n+1} = \frac{(me)_{fc}^{L}}{m_{fc}^{L}c_v} \tag*{(69)}
DfTfcDt=Tfcn+1−TfcnΔt(70)\frac{D_fT_{fc}}{Dt} = \frac{T_{fc}^{n+1}-T_{fc}^{n}}{\Delta t} \tag*{(70)}

As such, the Lagrangian specific volume rate is:

Δ(mv)fc=Vffcϕ∇⋅U+(ϕfcαfcDfTfcDt−ffcϕ∑n=1NϕncαncDnTncDt)(71)\Delta(mv)_{fc} = V f_{fc}^{\phi}\nabla\cdot U + \left(\phi_{fc}\alpha_{fc}\frac{D_fT_{fc}}{Dt} - f_{fc}^{\phi}\sum_{n=1}^{N}\phi_{nc}\alpha_{nc}\frac{D_nT_{nc}}{Dt}\right) \tag*{(71)}

where ffcϕ=(ϕfκf)/(∑n=1Nϕnκn)f_{fc}^{\phi}=(\phi_f\kappa_f)/(\sum_{n=1}^{N}\phi_n\kappa_n) and U=∇⋅(∑s=1NsϕscUsc+∑f=1NfϕfcUfc)U=\nabla\cdot(\sum_{s=1}^{N_s}\phi_{sc}U_{sc}+\sum_{f=1}^{N_f}\phi_{fc}U_{fc}). Finally, the Lagrangian specific volume is

(mv)fcL=Vρ‾f,cnvfcn+Δ(mv)fc(72)(mv)_{fc}^{L}=V\overline{\rho}_{f,c}^{n}v_{fc}^{n}+\Delta(mv)_{fc} \tag*{(72)}

Compute advection term and advance in time

The time advanced mass, linear momentum, energy and specific volume are:

mfcn+1=mfcL−Δt∇⋅(ρˉfcLUf,FCL)(73)m_{fc}^{n+1}=m_{fc}^{L}-\Delta t\nabla\cdot\left(\bar{\rho}_{fc}^{L}\mathbf{U}_{f,FC}^{L}\right) \tag*{(73)}
(mU)fcn+1=(mU)fcL−Δt∇⋅((ρˉU)fcLUf,FCL)(74)(m\mathbf{U})_{fc}^{n+1}=(m\mathbf{U})_{fc}^{L}-\Delta t\nabla\cdot\left((\bar{\rho}\mathbf{U})_{fc}^{L}\mathbf{U}_{f,FC}^{L}\right) \tag*{(74)}
(me)fcn+1=(me)fcL−Δt∇⋅((ρcvT‾)fcLUf,FCL)(75)(me)_{fc}^{n+1}=(me)_{fc}^{L}-\Delta t\nabla\cdot\left((\overline{\rho c_v T})_{fc}^{L}\mathbf{U}_{f,FC}^{L}\right) \tag*{(75)}
(mv)fcn+1=(mv)fcL−Δt∇⋅((ρˉv)fcLUf,FCL)(76)(mv)_{fc}^{n+1}=(mv)_{fc}^{L}-\Delta t\nabla\cdot\left((\bar{\rho}v)_{fc}^{L}\mathbf{U}_{f,FC}^{L}\right) \tag*{(76)}

Finally, the state variables of the fluid phases of the next time step are

ρˉfcn+1=mfcn+1V(77)\bar{\rho}_{fc}^{n+1}=\frac{m_{fc}^{n+1}}{V} \tag*{(77)}
Ufcn+1=(mU)fcn+1mfcn+1(78)\mathbf{U}_{fc}^{n+1}=\frac{(m\mathbf{U})_{fc}^{n+1}}{m_{fc}^{n+1}} \tag*{(78)}
Tfcn+1=(me)fcn+1mfcn+1(79)T_{fc}^{n+1}=\frac{(me)_{fc}^{n+1}}{m_{fc}^{n+1}} \tag*{(79)}
vfcn+1=(mv)fcn+1mfcn+1(80)v_{fc}^{n+1}=\frac{(mv)_{fc}^{n+1}}{m_{fc}^{n+1}} \tag*{(80)}

Interpolate from cell to node of the solid phase

First we interpolate the acceleration, velocity and temperature rate to the node

asin=∑ScidUscL(81)\mathbf{a}_{si}^{n}=\sum S_{ci}d\mathbf{U}_{sc}^{L} \tag*{(81)}
Usin+1=∑ScidUscLΔt(82)\mathbf{U}_{si}^{n+1}=\sum S_{ci}d\mathbf{U}_{sc}^{L}\Delta t \tag*{(82)}
dTsin=∑ScidTscL(83)dT_{si}^{n}=\sum S_{ci}dT_{sc}^{L} \tag*{(83)}

Then the boundary condition and contact forces are applied to the nodal velocity and the acceleration is modified by

asin=vsin+1−vsinΔt(84)\mathbf{a}_{si}^{n}=\frac{\mathbf{v}_{si}^{n+1}-\mathbf{v}_{si}^{n}}{\Delta t} \tag*{(84)}

Update the particle variables

The state variables of the solid phase [Uspn+1,xspn+1,∇Uspn+1,Tspn+1,∇Tspn+1,Fspn+1,Vspn+1][U_{sp}^{n+1}, x_{sp}^{n+1}, \nabla U_{sp}^{n+1}, T_{sp}^{n+1}, \nabla T_{sp}^{n+1}, \mathbf{F}_{sp}^{n+1}, V_{sp}^{n+1}] (velocity, position, velocity gradient, temperature, temperature gradient, deformation gradient, volume) are updated here

Uspn+1=Uspn+∑SspasinΔt(85)U_{sp}^{n+1} = U_{sp}^{n} + \sum S_{sp}a_{si}^{n}\Delta t \tag*{(85)}
xspn+1=xspn+∑SspUsin+1Δt(86)x_{sp}^{n+1} = x_{sp}^{n} + \sum S_{sp}U_{si}^{n+1}\Delta t \tag*{(86)}
∇Uspn+1=∑∇SspUsin+1(87)\nabla U_{sp}^{n+1} = \sum\nabla S_{sp}U_{si}^{n+1} \tag*{(87)}
Tspn+1=Tspn+∑SspdTsinΔt(88)T_{sp}^{n+1} = T_{sp}^{n} + \sum S_{sp}dT_{si}^{n}\Delta t \tag*{(88)}
∇Tspn+1=∑∇SspTspnΔt(89)\nabla T_{sp}^{n+1} = \sum\nabla S_{sp}T_{sp}^{n}\Delta t \tag*{(89)}
Fspn+1=(I+∇Uspn+1Δt)Fspn(90)\mathbf{F}_{sp}^{n+1} = \left(\mathbf{I} + \nabla U_{sp}^{n+1}\Delta t\right)\mathbf{F}_{sp}^{n} \tag*{(90)}
Vspn+1=det⁡(Fspn+1)Vspn(91)V_{sp}^{n+1} = \det\left(\mathbf{F}_{sp}^{n+1}\right)V_{sp}^{n} \tag*{(91)}

Finally, the effective stress (σ′)n+1(\boldsymbol{\sigma}')^{n+1} is updated from the constitutive model and the pore water pressure is interpolated from the cell as:

pfn+1=∑SsiPcn+1(92)p_f^{n+1} = \sum S_{si}P_c^{n+1} \tag*{(92)}

Numerical examples

All input files and the analytical calculations in this section are provided in the Github repository for the reproduction of the numerical results.

Fluid Flow through isothermal porous media

Fluid flow through porous media is important in many engineering disciplines, like predicting water flow in soil. Fluid flow velocity in one dimension can be calculated from the porous media’s hydraulic conductivity KK as:

Uf=KΔpfL(93)U_f = K\frac{\Delta p_f}{L} \tag*{(93)}

If the Carman-Kozeny formula is adopted F=10ϕs/(1−ϕs)2F = 10\phi_s/(1-\phi_s)^2, the hydraulic conductivity will be expressed as K=d2(1−ϕs)3/(180μϕs2)K = d^2(1-\phi_s)^3/(180\mu\phi_s^2). Then, the analytical formula of average velocity in one dimension through the porous media is:

Uf=1nd2(1−ϕs)3180μϕs2ΔpfL(94)U_f = \frac{1}{n}\frac{d^2(1-\phi_s)^3}{180\mu\phi_s^2}\frac{\Delta p_f}{L} \tag*{(94)}

Our numerical model is validated by modeling fluid flow through a 1m long porous media. This fluid has water properties (bulk modulus is 2GPa, density is 998 kg/m3 at 5 degrees Celsius and 10325 Pa (1atm) pressure, dynamic viscosity μ\mu is 1mPa s). The porous media is modeled by elastic material with Young’s modulus is 10 MPa, Poisson’s ratio is 0.3, and density is 2650 kg/m3. The volume fraction of porous media ϕs\phi_s is [0.6, 0.62, 0.66, 0.68, 0.7] and the average grain diameter dd is 1mm. The model is discretized in 20 finite element and the porous media in 10 finite element with 1 material point per element. The pressure gradient is applied with three different value [0.25, 0.5, 1] atm. Figure 6 shows a good agreement of fluid flow prediction between the theory and the model.

Numerical results of the fluid flow through isothermal porous media

Figure 6. (a) Discretization of the model (b) Comparision between analytical model and simulation. Figure 6: Numerical results of the fluid flow through isothermal porous media

Isothermal consolidation

A common benchmark fo a fully saturated porous media is the simulation of one-dimensional consolidation. Using the Carman-Kozeny formula, the time-dependent pressure can be caluated as:

pf=∑m=1∞2FextMsin⁡(MzH)e−M2Tv with M=π2(2m+1)(95)p_f = \sum_{m=1}^{\infty} \frac{2F_{ext}}{M} \sin\left(\frac{Mz}{H}\right)e^{-M^{2}T_v} \text{ with } M = \frac{\pi}{2}(2m+1) \tag*{(95)}

where the consolidation rate Tv=Cvt/H2T_v = C_vt/H^2, the consolidation coefficient Cv=Evn3d2/(180(1−n)2μ)C_v = E_v n^3d^2/(180(1-n)^2\mu) and the Oedometer modulus Ev=E(1−ν)/(1+ν)/(1−2ν)E_v = E(1-\nu)/(1+\nu)/(1-2\nu). Our numerical model is validated by modeling the consolidation of a 1m column. This fluid has water properties (bulk modulus is 2GPa, density is 998 kg/m3 at 5 degrees Celsius and 101325 Pa (1atm) pressure, dynamic viscosity μ\mu is 1mPa s). The porous media is modeled by elastic material with Young’s modulus is 10 MPa, Poisson’s ratio is 0.3, and density is 2650 kg/m3. The volume fraction of porous media ϕs\phi_s is 0.7 which is equivalent to the porosity of 0.3 and the average grain diameter dd is 1mm. The model is discretized in 100 finite element with 1 material point per element. The external pressure applies to the top of the column is 10 kPa. Figure 7 shows a good agreement of fluid flow prediction between the theory and the model.

Comparison between analytical solution and numerical solution

Figure 7. Compasion between analytical solution and numerical solution

Model schematic

Figure 8. Model schematic [23]

Thermal induced cavity flow

Another benchmark is the thermal induced cavity flow in porous media. Temperature and velocity distributions are calculated for a square non-deformable saturated porous media The top and bottom walls are insulated, and the left and right walls are at fixed temperatures differing by 1 degree. The fluid motion at stead state are cavity flow due to the temperature induced density variation.

The numerical is validated by comparing with the numerical solution of the finite element method. The fluid has water properties (bulk modulus is 2GPa, density is 998 kg/m3 at 5 degrees Celsius and 10325 Pa (1atm) pressure, dynamic viscosity μ\mu is 1 mPa s). The porous media is modeled by non deformable material, and density is 2500 kg/m3. The specific heat capacity of the water and porous skeleton are 4181 J/kg.K and 835 J/kg.K respectively. The thermal conductivity of the water and porous skeleton are 0.598 W/m.K and 0.4 W/m.K. The volume fraction of porous media ϕs\phi_s is 0.6 which is equivalent to the porosity of 0.4 and the average grain diameter dd is 1mm. The model is discretized in 20 x 20 finite element with 4 material point per element. Figure 9 shows a good agreement of numerical results of the model compared with the numerical solution of the finite element method.

MPMICE and FEM model comparison

Figure 9. (a) MPMICE model (b) FEM model [23]. Comparision between MPMICE model and FEM model

Underwater debris flow

The numerical example is validated by Rzadkiewicz et al.’s experiment on submarine debris flow [24]. During the experiment, sand in a triangular box is released and then slides along a rigid bed inclined 45 degrees under water, see Figure 10.

Model schematic

Figure 10. Model schematic

In the numerical model, the material properties are selected based on the experiment by Rzadkiewicz et al [24]. Sand has a saturated density of 1985 kg/m3kg/m^3 and yield stress of 200 Pa. Young’s modulus has little effect on debris flow run-out because of the extreme large deformation of the debris. Therefore, we select 50 MPa Young’s modulus with 0.25 Poisson’s ratio. The rigid bed is much stiffer with bulk modulus and shear modulus of 117E7117E^7 Pa and 43.8E743.8E^7 Pa. Under gravity, the density of the water at the surface is 999.8 kg/m3kg/m^3 at the pressure of 1 atm. At the top boundary, the air has a density of 1.17 kg/m3kg/m^3 at the atmospheric pressure of 1 atm. At 5 Celcius degrees, air and water have viscosity of 18.45E−318.45E^{-3} mPa s and 1 mPa s respectively. The numerical parameters used in this example are presented in Table 1 (PDF p. 33).

MaterialsBulk modul (Pa)Shear modul (Pa)Density (kg/m3)Temp (C)Dynamic viscosity (Pa s)Yield stress (Pa)
Water (at surface)2.15e9-999.85855e-6-
Air (at top boundary)--1.177518.45e-6-
Sand (porous media)8.33e620e619855-200
Rigid bed (solid)117e743.8e789005--

Table 1 (PDF p. 33). Numerical parameters for the underwater submarine debris

On all boundary faces, the Dirichlet boundary condition is imposed for velocity (u=0u = 0 m/s) and temperature (T=5T = 5 Celcius degrees), while the Neuman boundary condition is imposed at the top boundary for pressure (dp/dx=0dp/dx = 0 kPa) and density (dρ/dx=0d\rho/dx = 0 kg/m3kg/m^3). For the background mesh, there are

700×400=280,000700 \times400 = 280{,}000 cells. In each cell of the debris flow and rigid bed, there are 2×22 \times2 material points.

Figure 11a and Figure 11b show snapshots of the debris flow sliding in the plane at 0.4 s and 0.8 s. Our simulations match the computed results from Rzadkiewicz et al. [24]. The model also captures typical hydroplaning mechanism of the underwater debris flow (hydroplaning means the debris flow is lifted up and no longer in contact with the bottom layer). The elevation of the free surface at 0.4 s and 0.8 s is compared between our proposed method and other methods in Figure 12. Once again, our computed results were consistent with both the experiment and others computational results [7]. Unlike other computational models based on total stress analysis, the proposed model based on the effective stress analysis which allows to analyze the water pressure and temperature in the debris flow.

Simulation of underwater debris flow at 0.4 and 0.8 seconds

Figure 11. Simulation of underwater debris flow

Simulation at 0.4 seconds

(a) (a) 0.4 seconds

Simulation at 0.8 seconds

(b) (b) 0.8 seconds

Figure 12. Simulation of underwater debris flow

We also explore the difference between underwater debris flow and saturated debris flow in terms of interacting with obstacle. Figure 13 shows the snapshot of the simulations of underwater and saturated debris flow. The saturated debris flow (see Figure 13a) behaves like frictional flow as grain have contact forces with each other. On the other hand, the underwater debris flow (see Figure 13b) behaves like turbulent flow as grains are separated from each other and exhibit no contact forces between grains.

Saturated debris flow using MPM

(a) (a) saturated debris flow using MPM

Underwater debris flow using MPMICE

(b) (b) underwater debris flow using MPMICE

Figure 13. Simulation of underwater debris flow

Earthquake-induced submarine landslides

acceleration

(a) acceleration

velocity

(b) velocity

Figure 15. Ground acceleration profile, frequency of 2Hz and magnitude of 1g

In the final example, we perform numerical analysis of the earthquake induced submarine landslides. A plane strain model with the slope under water is shown in Figure 14. A 20m high slope with slope gradient of 45 degrees is placed in a horizontal and vertical structure which was used to be a skaing table to apply earthquake loading. We simplify the earthquake loading by simulating the ground shaking for 20 seconds with the peak ground acceleration of 1g and the frequency of 2Hz (Figure 15a). The ground motion is applied in terms of velocity (Figure 15b). The earthquake of this magnitude can occured typically for the earthquake of magnitude of more than 6.

Numerical model of the earthquake-induced submarine landslide

Figure 14. Numerical model of the earthquake-induced submarine landslide

A non-associated Mohr-Coulomb model is used for the soil. The soil grain has the density of 2650 kg/m3\mathrm{kg}/\mathrm{m}^{3}, Young’s modulus of 10 kPa and Poisson’s ratio of 0.3 and zero cohesion. The mobilized friction angle ϕm′\phi'_m is governed following the softening curve (see Figure 16) with the peak friction angle ϕp′\phi'_p of 45 degrees and the residual friction angle ϕr′\phi'_r of 10 degrees. The porosity is 0.3 and the average grain size of the soil is around 0.1 μm\mu\mathrm{m} to mimic the undrained behavior. The mobilized dilatancy angle is calculated from the Row-stress dilatancy as follow:

Mobilized friction angle in Mohr Coulomb model

Figure 16. Mobilized friction angle in Mohr Coulomb model

sin⁡ψm′=sin⁡ϕm′−sin⁡ϕr′1−(sin⁡ϕr′sin⁡ϕm′)(96)\sin\psi'_m = \frac{\sin\phi'_m - \sin\phi'_r}{1 - (\sin\phi'_r \sin\phi'_m)} \tag*{(96)}

The solid plane is modeled as a rigid body acted as a shaking table. The contact between horizontal plane and the sand is the frictional contact with the friction coefficient of 0.1. No artificial damping is applied in the simulation. The contact between vertical plane and the sand is considered to be smooth with zero friction coefficient. Under gravity, the density of the water at the surface is 999.8 kg/m3\mathrm{kg}/\mathrm{m}^{3} at the pressure of 1 atm. At the top boundary, the air has a density of 1.17 kg/m3\mathrm{kg}/\mathrm{m}^{3} at the atmospheric pressure of 1 atm. At 5 Celcius degrees, air and water have viscosity of 18.45×10−318.45 \times10^{-3} mPa s and 1 mPa s respectively. On all boundary faces, the symmetric boundary condition is imposed, while the Neuman boundary condition is imposed at the top boundary for pressure (dp/dx=0\mathrm{d}p/\mathrm{d}x = 0 kPa) and density (dρ/dx=0\mathrm{d}\rho/\mathrm{d}x = 0 kg/m3\mathrm{kg}/\mathrm{m}^{3}). The mesh size is 0.25 x 0.25m with 300852 element cells and 142316 material points. The simulation takes a couple of hours to perform 60 seconds of the simulation using 4096 CPUs.

We demonstrate the entire process and the mechanism of the earthquake-induced submarine landslides by showing the shear strain (Figure 17), the pore water ressure in atm (Figure 18) and the velocity (Figure 19). The failure mechanism can be charaterized as the progressive failure mechanism. Here are some numerical observation:

Shear strain during the earthquake-induced submarine landslides

Figure 17. Shear strain during the earthquake-induced submarine landslides

Pore water pressure during the earthquake-induced submarine landslides

Figure 18. pore water pressure during the earthquake-induced submarine landslides

Velocity during the earthquake-induced submarine landslides

Figure 19. Velocity during the earthquake-induced submarine landslides

  1. At the initial of the seismic event, the seismic loading triggers the first slide at 3 seconds. At 4 seconds, the debris start to move with the maximum speed of around 2-3 m/s with multiple shear band developed in the slope. The wave generated from the submarine slide is around 2-3m towards the slide direction.

  1. When the onset of the shear band occurs in the slope (for example at 4 seconds and 20 seconds), the negative excess pore water pressure is developed along this shear band with pore water pressure is under 1atm. This is a typical dilatancy behavior when the soil is sheared rapidly in the undrained behavior.

  1. When the seismic loading ends at 23 seconds, the last shear band is mobilized and the slope soon reaches to the final deposition. No more progressive failure developed in the slope. The turbulent flow developed as the interaction between debris flow and seawater.

Overall, we show the completed process of the earthquake-induced submarine landslides involving (1) earthquake triggering mechanism, (2) the onset of the shear band with the delvelopment of negative excess pore water pressure, (3) progressive failure mechanism, (4) submarine landslide induced wave to final deposition.

Conclusions

We have presented a numerical approach MPMICE for the simulation of large deformation soil-fluid-structure interaction, emphasizing the simulation of the earthquake-induced submarine landslides. The model uses (1) the Material Point Method for capturing the large deformation of iso-thermal porous media and solid structures and (2) Implicit Continuous Eulerian (compressible, conservative multi-material CFD formulation) for modeling the complex fluid flow including turbulence. This model is implemented in the high-performance Uintah computational framework and validated against analytical solution and experiment. We then demonstrate the capability of the model to simulate the entire process of the earthquake induced submarine landslides.

Acknowledgements

The authors gratefully acknowledge Dr. James Guilkey and Dr. Todd Harman from the University of Utah for sharing the insight on the theoretical framework of MPMICE which this work is based. This project has received funding from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie Actions (MSCA) Individual Fellowship (Project SUBSLIDE “Submarine landslides and their impacts on offshore infrastructures”) grant agreement 101022007. The authors would also like to acknowledge the support from the Research Council of Norway through its Centers of Excellence funding scheme, project number 262644 Porelab. The computations were performed on High Performance Computing resources provided by UNINETT Sigma2 - the National Infrastructure for High Performance Computing and Data Storage in Norway.

Equation derivation

Before deriving the governing equation, we define the Lagrangian derivative for a state variable ff as:

DffDt=∂f∂t+Uf⋅∇fDsfDt=∂f∂t+Us⋅∇f(97)\frac{D_f f}{Dt} = \frac{\partial f}{\partial t} + \mathbf{U}_f \cdot\nabla f \qquad\frac{D_s f}{Dt} = \frac{\partial f}{\partial t} + \mathbf{U}_s \cdot\nabla f \tag*{(97)}

we use some definition following [16] as below:

−1V[∂Vf∂p]≡κfisothermal compressibility of fluid(98)-\frac{1}{V}\left[\frac{\partial V_f}{\partial p}\right] \equiv\kappa_f \qquad\text{isothermal compressibility of fluid} \tag*{(98)}
1V[∂Vf∂T]≡αfcontant pressure thermal expansivity of fluid(99)\frac{1}{V}\left[\frac{\partial V_f}{\partial T}\right] \equiv\alpha_f \qquad\text{contant pressure thermal expansivity of fluid} \tag*{(99)}

Then, the rate of volume with incompressible solid grains are calculated as below:

1VDfVfDt=1V([∂Vf∂p]DfPeqDt+[∂Vf∂Tf]DfTDt)=1V(−κfDfPeqDt+αfDfTfDt)(100)\frac{1}{V}\frac{D_f V_f}{Dt} = \frac{1}{V}\left(\left[\frac{\partial V_f}{\partial p}\right]\frac{D_f P_{\mathrm{eq}}}{Dt}+\left[\frac{\partial V_f}{\partial T_f}\right]\frac{D_f T}{Dt}\right)=\frac{1}{V}\left(-\kappa_f\frac{D_f P_{\mathrm{eq}}}{Dt}+\alpha_f\frac{D_f T_f}{Dt}\right) \tag*{(100)}

Evolution of porosity

Solving the solid mass balance equation (4) with the definition of solid mass in equation (2), it leads to the rate of porosity as below:

DsmsDt=Ds(ϕsρsV)Dt=ρsVDsϕsDt+ϕsVDsρsDt+ϕsρsDsVDt=0(101)\frac{D_s m_s}{Dt}=\frac{D_s(\phi_s\rho_s V)}{Dt}=\rho_s V\frac{D_s\phi_s}{Dt}+\phi_s V\frac{D_s\rho_s}{Dt}+\phi_s\rho_s\frac{D_s V}{Dt}=0 \tag*{(101)}

The soil grains are assumed to be incompressible, therefore, term 2 in the right hand side is zero.

VDsϕsDt+ϕsDsVDt=0(102)V\frac{D_s\phi_s}{Dt}+\phi_s\frac{D_sV}{Dt}=0 \tag*{(102)}

Dividing all terms with VV with the equation 1VDsVDt=∇⋅Us\frac{1}{V}\frac{D_sV}{Dt}=\nabla\cdot\mathbf{U}_s, it leads to:

DsnDt=∂n∂t+Us⋅∇n=ϕs∇⋅Us(103)\frac{D_sn}{Dt}=\frac{\partial n}{\partial t}+\mathbf{U}_s\cdot\nabla n=\phi_s\nabla\cdot\mathbf{U}_s \tag*{(103)}

Momentum conservation

The linear momentum balance equation for the fluid phases based on mixture theory is:

1VDf(mfUf)Dt=∇⋅(−ϕfpfI)+∇⋅τf+ρˉfb+∑fd+fb(104)\frac{1}{V}\frac{D_f(m_f\mathbf{U}_f)}{Dt}=\nabla\cdot(-\phi_fp_f\mathbf{I})+\nabla\cdot\boldsymbol{\tau}_f+\bar{\rho}_f\mathbf{b}+\sum\mathbf{f}_d+\mathbf{f}_b \tag*{(104)}

On the right hand sand, the first term is the divergence of partial fluid phase stress, the third term is the body force, the fourth term is the drag force (momentum exchange) and the fifth term is the buoyant force described in [25] for the immiscible mixtures. The buoyant force is in the form:

fb=σf∇(n)(105)\mathbf{f}_b=\sigma_f\nabla(n) \tag*{(105)}

As a result, the linear momentum balance equation for the fluid phases becomes:

1VDf(mfUf)Dt=1V[∂(mfUf)∂t+∇⋅(mfUfUf)]=−ϕf∇pf+∇⋅τf+ρˉfb+∑fd(106)\frac{1}{V}\frac{D_f(m_f\mathbf{U}_f)}{Dt} =\frac{1}{V}\left[\frac{\partial(m_f\mathbf{U}_f)}{\partial t}+\nabla\cdot(m_f\mathbf{U}_f\mathbf{U}_f)\right] =-\phi_f\nabla p_f+\nabla\cdot\boldsymbol{\tau}_f+\bar{\rho}_f\mathbf{b}+\sum\mathbf{f}_d \tag*{(106)}

The Reynolds stress component can be included in the term τf\boldsymbol{\tau}_f to consider the turbulent effects if needed. To derive the linear momentum balance equation for the solid phase, we begin with the linear momentum balance equation for the mixture as:

1VDf(mfUf)Dt+1VDs(msUs)Dt=∇⋅(σ)+ρˉfb+ρˉsb(107)\frac{1}{V}\frac{D_f(m_f\mathbf{U}_f)}{Dt}+\frac{1}{V}\frac{D_s(m_s\mathbf{U}_s)}{Dt} =\nabla\cdot(\boldsymbol{\sigma})+\bar{\rho}_f\mathbf{b}+\bar{\rho}_s\mathbf{b} \tag*{(107)}

Combining Terzaghi’s equation (3) and subtracting both sides with equation (106), we obtain the linear momentum balance equation for the solid phase as:

1VDs(msUs)Dt=∇⋅(σ′)−ϕs∇pf+ρˉsb−∑fd+∑ffric(108)\frac{1}{V}\frac{D_s(m_s\mathbf{U}_s)}{Dt} =\nabla\cdot(\boldsymbol{\sigma}')-\phi_s\nabla p_f+\bar{\rho}_s\mathbf{b}-\sum\mathbf{f}_d+\sum\mathbf{f}_{fric} \tag*{(108)}

Here the ffric\mathbf{f}_{fric} stems from the soil-structure interaction following the contact law between the soil/structure interfaces.

Energy conservation

We adopt the general form of the total energy balance equation for the porous media from [26], the total energy balance equations for the fluid phases are:

1VDf(mf(ef+0.5Uf2))Dt=∇⋅(−npfI)⋅Uf+∇⋅qf+(ρ‾fb)⋅Uf+∑fd⋅Uf+∑qsf(109)\frac{1}{V}\frac{D_f\left(m_f\left(e_f+0.5U_f^2\right)\right)}{Dt} = \nabla\cdot\left(-np_f\mathbf{I}\right)\cdot\mathbf{U}_f+\nabla\cdot\mathbf{q}_f+\left(\overline{\rho}_f\mathbf{b}\right)\cdot\mathbf{U}_f+\sum\mathbf{f}_d\cdot\mathbf{U}_f+\sum q_{sf} \tag*{(109)}

Applying the product rule D(mU2)=D(mU⋅U)=2U⋅D(mU)D(mU^2)=D(m\mathbf{U}\cdot\mathbf{U})=2\mathbf{U}\cdot D(m\mathbf{U}), the left hand side of equation (109) becomes:

1VDf(mf(ef+0.5Uf2))Dt=1VDf(mfef)Dt+1VDf(mfUf)Dt⋅Uf(110)\frac{1}{V}\frac{D_f\left(m_f\left(e_f+0.5U_f^2\right)\right)}{Dt} = \frac{1}{V}\frac{D_f(m_fe_f)}{Dt} +\frac{1}{V}\frac{D_f(m_f\mathbf{U}_f)}{Dt}\cdot\mathbf{U}_f \tag*{(110)}

Combining equations (106), (109), (110), we obtain the final form of the internal energy balance equation for the fluid phases as:

1VDf(mfef)Dt=1V[∂(mfef)∂t+∇⋅(mfefUf)]=ρ‾fpfDfνfDt+∇⋅qf+∑qsf(111)\frac{1}{V}\frac{D_f(m_fe_f)}{Dt} = \frac{1}{V}\left[\frac{\partial(m_fe_f)}{\partial t}+\nabla\cdot(m_fe_f\mathbf{U}_f)\right] = \overline{\rho}_fp_f\frac{D_f\nu_f}{Dt}+\nabla\cdot\mathbf{q}_f+\sum q_{sf} \tag*{(111)}

On the right hand side, the terms include the average pressure-volume work, the average viscous dissipation, the thermal transport and the energy exchange between solid and fluid respectively. The heat flux is qf=ρ‾fβf∇Tf\mathbf{q}_f=\overline{\rho}_f\beta_f\nabla T_f with βf\beta_f being the thermal conductivity coefficient. To derive the internal energy balance equation for the solid phase, we introduce the rate of the internal energy for the thermoelastic materials as a function of elastic strain tensor εse\boldsymbol{\varepsilon}_s^e and temperature TsT_s:

msVDs(es)Dt=σ′:Ds(εse)Dt+Ds(es)Ds(Ts)Ds(Ts)Dt=σ′:Ds(εse)Dt+cvDs(Ts)Dt(112)\frac{m_s}{V}\frac{D_s(e_s)}{Dt} =\boldsymbol{\sigma}' : \frac{D_s(\boldsymbol{\varepsilon}_s^e)}{Dt} +\frac{D_s(e_s)}{D_s(T_s)}\frac{D_s(T_s)}{Dt} =\boldsymbol{\sigma}' : \frac{D_s(\boldsymbol{\varepsilon}_s^e)}{Dt} +c_v\frac{D_s(T_s)}{Dt} \tag*{(112)}

cvc_v is the specific heat at the constant volume of the solid materials. The total energy balance equation for the mixture based on [26] can be written as:

1VDf(mf(ef+0.5Uf2))Dt+1VDs(ms(es+0.5Us2))Dt=∇⋅(−ϕfpfI)⋅Uf+∇⋅(σ′−ϕspfI)⋅Us+(−ϕfpfI):∇Uf+σ′:∇Us+(ρ‾fb)⋅Uf+(ρ‾sb)⋅Us+∇⋅qf+∇⋅qs+∑fd⋅(Uf−Us)(113)\begin{aligned} \frac{1}{V}\frac{D_f\left(m_f\left(e_f+0.5U_f^2\right)\right)}{Dt} +\frac{1}{V}\frac{D_s\left(m_s\left(e_s+0.5U_s^2\right)\right)}{Dt} ={}&\nabla\cdot\left(-\phi_fp_f\mathbf{I}\right)\cdot\mathbf{U}_f\\ &+\nabla\cdot\left(\boldsymbol{\sigma}'-\phi_sp_f\mathbf{I}\right)\cdot\mathbf{U}_s +\left(-\phi_fp_f\mathbf{I}\right):\nabla\mathbf{U}_f +\boldsymbol{\sigma}':\nabla\mathbf{U}_s\\ &+\left(\overline{\rho}_f\mathbf{b}\right)\cdot\mathbf{U}_f +\left(\overline{\rho}_s\mathbf{b}\right)\cdot\mathbf{U}_s +\nabla\cdot\mathbf{q}_f+\nabla\cdot\mathbf{q}_s +\sum\mathbf{f}_d\cdot\left(\mathbf{U}_f-\mathbf{U}_s\right) \tag*{(113)} \end{aligned}

Subtracting equation (113), (112) to equations (109) and (108), we obtained the internal energy balance equation for solid phase as:

σ′:Ds(εse)Dt+msVcvDs(Ts)Dt=ΔWs+ΔWfriction+∇⋅qs−∑qsf(114)\boldsymbol{\sigma}' : \frac{D_s(\boldsymbol{\varepsilon}_s^{e})}{Dt} + \frac{m_s}{V}c_v \frac{D_s(T_s)}{Dt} = \Delta W_s + \Delta W_{friction} + \nabla\cdot\boldsymbol{q}_s - \sum q_{sf} \tag*{(114)}

On the right hand side, the terms include the work rate from frictional sliding between solid materials ΔWfriction\Delta W_{friction}, thermal transport and energy exchange between solid and fluid respectively. The heat flux is qs=ρˉsβs∇Ts\boldsymbol{q}_s = \bar{\rho}_s\beta_s\nabla T_s with βs\beta_s being the thermal conductivity of the solid materials, the mechanical work rate ΔWs=σ′:Ds(εs)Dt=σ′:(Ds(εse)Dt+Ds(εsp)Dt)\Delta W_s = \boldsymbol{\sigma}' : \frac{D_s(\boldsymbol{\varepsilon}_s)}{Dt} = \boldsymbol{\sigma}' : \left(\frac{D_s(\boldsymbol{\varepsilon}_s^e)}{Dt} + \frac{D_s(\boldsymbol{\varepsilon}_s^p)}{Dt}\right) computed from the constitutive model with εsp\boldsymbol{\varepsilon}_s^p is the plastic strain tensor, . By subtracting the term σ′:Ds(εse)Dt\boldsymbol{\sigma}' : \frac{D_s(\boldsymbol{\varepsilon}_s^e)}{Dt}, we get the final form of the energy balance equation as:

msVcvDs(Ts)Dt=σ′:Ds(εsp)Dt+ΔWfriction+∇⋅qs−∑qsf(115)\frac{m_s}{V}c_v \frac{D_s(T_s)}{Dt} = \boldsymbol{\sigma}' : \frac{D_s(\boldsymbol{\varepsilon}_s^p)}{Dt} + \Delta W_{friction} + \nabla\cdot\boldsymbol{q}_s - \sum q_{sf} \tag*{(115)}

Advanced Fluid Pressure

The discretization of the pressure equation begins with the Lagrangian face-centered velocity and the equation for the pressure

ρˉf,FCUf,FCn+1−Uf,FCndt=n∇FCPfcn+1+ρˉf,FCb(116)\bar{\rho}_{f,FC}\frac{U_{f,FC}^{n+1}-U_{f,FC}^{n}}{dt} = n\nabla^{FC}P_{fc}^{n+1} + \bar{\rho}_{f,FC}\boldsymbol{b} \tag*{(116)}
κdPdt=∇c⋅Uf,FCn+1(117)\kappa\frac{dP}{dt} = \nabla^c \cdot U_{f,FC}^{n+1} \tag*{(117)}

The divergence of the equation (116) with ∇⋅b=0\nabla\cdot\boldsymbol{b}=0 is

∇c⋅Uf,FCn+1−∇c⋅Uf,FCn=∇cΔtρf,FCn⋅∇FC(Pfcn+ΔPfcn)(118)\nabla^c \cdot U_{f,FC}^{n+1} - \nabla^c \cdot U_{f,FC}^{n} = \nabla^c\frac{\Delta t}{\rho_{f,FC}^{n}} \cdot\nabla^{FC}(P_{fc}^{n}+\Delta P_{fc}^{n}) \tag*{(118)}

To solve this equation, we define the face-centered intermediate velocity Uf,FC∗U_{f,FC}^{*} as:

ρˉf,FCUf,FC∗−Uf,FCnΔt=n∇FCPfcn+ρˉf,FCb(119)\bar{\rho}_{f,FC}\frac{U_{f,FC}^{*}-U_{f,FC}^{n}}{\Delta t} = n\nabla^{FC}P_{fc}^{n} + \bar{\rho}_{f,FC}\boldsymbol{b} \tag*{(119)}

The divergence of the equation (119) is

∇c⋅Uf,FC∗−∇c⋅Uf,FCn=∇cΔtρf,FCn⋅∇FCPfcn(120)\nabla^c \cdot U_{f,FC}^{*} - \nabla^c \cdot U_{f,FC}^{n} = \nabla^c\frac{\Delta t}{\rho_{f,FC}^{n}} \cdot\nabla^{FC}P_{fc}^{n} \tag*{(120)}

Combining equations (117, 118, 120), it leads to

(κ−∇cΔtρf,FCn⋅∇FC)ΔPfcn=−∇c⋅Uf,FC∗(121)\left(\kappa-\nabla^{c}\frac{\Delta t}{\rho^{n}_{f,FC}}\cdot\nabla^{FC}\right)\Delta P^{n}_{fc}=-\nabla^{c}\cdot\mathbf{U}^{*}_{f,FC} \tag*{(121)}

When the fluid is incompressible, κ\kappa approaches to zero and the equation (121) becomes the Poisson’s equation for the incompressible fluid flow.

Momentum and Energy exchange with an implicit solver

Considering the fluid momentum balance equation as

(mU)f,FCn+1=(mU)f,FCn−Δt(Vn∇FCPfcn+mfb)+VKΔt(Us,FCn+1−Uf,FCn+1)(122)(m\mathbf{U})^{n+1}_{f,FC}=(m\mathbf{U})^{n}_{f,FC}-\Delta t\left(Vn\nabla^{FC}P^{n}_{fc}+m_{f}\mathbf{b}\right)+VK\Delta t\left(\mathbf{U}^{n+1}_{s,FC}-\mathbf{U}^{n+1}_{f,FC}\right) \tag*{(122)}

Assuming mf,FCn+1=mf,FCnm^{n+1}_{f,FC}=m^{n}_{f,FC} we get

Uf,FCn+1=Uf,FCn−Δt(∇FCPfcnρf,FCn+b)+ΔtKρf,FCn(Us,FCn+1−Uf,FCn+1)(123)\mathbf{U}^{n+1}_{f,FC}=\mathbf{U}^{n}_{f,FC}-\Delta t\left(\frac{\nabla^{FC}P^{n}_{fc}}{\rho^{n}_{f,FC}}+\mathbf{b}\right)+\frac{\Delta tK}{\rho^{n}_{f,FC}}\left(\mathbf{U}^{n+1}_{s,FC}-\mathbf{U}^{n+1}_{f,FC}\right) \tag*{(123)}

As defined in the section ’Advanced Fluid Pressure’, the face-centered intermediate fluid velocity Uf,FC∗=Δt(∇FCPfcn/ρf,FCn+b)\mathbf{U}^{*}_{f,FC}=\Delta t(\nabla^{FC}P^{n}_{fc}/\rho^{n}_{f,FC}+\mathbf{b}) leading to

Uf,FCn+1=Uf,FC∗+ΔtKρf,FCn(Us,FCn+1−Uf,FCn+1)(124)\mathbf{U}^{n+1}_{f,FC}=\mathbf{U}^{*}_{f,FC}+\frac{\Delta tK}{\rho^{n}_{f,FC}}\left(\mathbf{U}^{n+1}_{s,FC}-\mathbf{U}^{n+1}_{f,FC}\right) \tag*{(124)}

Considering the solid momentum balance equation as

(mU)s,FCn+1=(mU)s,FCn−Δt(V∇FC⋅σn−V(1−n)∇FCPfcn+msb)−VKΔt(Us,FCn+1−Uf,FCn+1)(125)(m\mathbf{U})^{n+1}_{s,FC}=(m\mathbf{U})^{n}_{s,FC}-\Delta t\left(V\nabla^{FC}\cdot\boldsymbol{\sigma}^{n}-V(1-n)\nabla^{FC}P^{n}_{fc}+m_{s}\mathbf{b}\right)-VK\Delta t\left(\mathbf{U}^{n+1}_{s,FC}-\mathbf{U}^{n+1}_{f,FC}\right) \tag*{(125)}

We define the face-centered intermediate solid velocity as Us,FC∗=Δt(∇FC⋅σn/ρs,FC−∇FCPfcn/ρs+b)\mathbf{U}^{*}_{s,FC}=\Delta t(\nabla^{FC}\cdot\boldsymbol{\sigma}^{n}/\rho_{s,FC}-\nabla^{FC}P^{n}_{fc}/\rho_{s}+\mathbf{b}) leading to

Us,FCn+1=Us,FC∗−ΔtKρs,FCn(Us,FCn+1−Uf,FCn+1)(126)\mathbf{U}^{n+1}_{s,FC}=\mathbf{U}^{*}_{s,FC}-\frac{\Delta tK}{\rho^{n}_{s,FC}}\left(\mathbf{U}^{n+1}_{s,FC}-\mathbf{U}^{n+1}_{f,FC}\right) \tag*{(126)}

Combining equation (124) and (126) we get

Uf,FC∗+ΔUf,FC=Uf,FC∗+ΔtKρf,FCn(Us,FC∗+ΔUs,FC−Uf,FC∗−ΔUf,FC)\mathbf{U}^{*}_{f,FC}+\Delta\mathbf{U}_{f,FC}=\mathbf{U}^{*}_{f,FC}+\frac{\Delta tK}{\rho^{n}_{f,FC}}\left(\mathbf{U}^{*}_{s,FC}+\Delta\mathbf{U}_{s,FC}-\mathbf{U}^{*}_{f,FC}-\Delta\mathbf{U}_{f,FC}\right)
Us,FC∗+ΔUs,FC=Us,FC∗−ΔtKρs,FCn(Us,FC∗+ΔUs,FC−Uf,FC∗−ΔUf,FC)(127)\mathbf{U}^{*}_{s,FC}+\Delta\mathbf{U}_{s,FC}=\mathbf{U}^{*}_{s,FC}-\frac{\Delta tK}{\rho^{n}_{s,FC}}\left(\mathbf{U}^{*}_{s,FC}+\Delta\mathbf{U}_{s,FC}-\mathbf{U}^{*}_{f,FC}-\Delta\mathbf{U}_{f,FC}\right) \tag*{(127)}

Rearranging the equation (127), it leads to the linear system of equations

(1+β12,FC−β12,FC−β21,FC1+β21,FC)(ΔUf,FCΔUs,FC)=(β12,FC(Uf,FC∗−Uf,FC∗)β21,FC(Uf,FC∗−Us,FC∗))\begin{pmatrix} 1+\beta_{12,FC} & -\beta_{12,FC} \\ -\beta_{21,FC} & 1+\beta_{21,FC} \end{pmatrix} \begin{pmatrix} \Delta U_{f,FC} \\ \Delta U_{s,FC} \end{pmatrix} = \begin{pmatrix} \beta_{12,FC}(U^{*}_{f,FC}-U^{*}_{f,FC}) \\ \beta_{21,FC}(U^{*}_{f,FC}-U^{*}_{s,FC}) \end{pmatrix}

Solving this linear equations with β12,FC=(ΔtK)/ρˉf,FCn\beta_{12,FC}=(\Delta tK)/\bar{\rho}^{n}_{f,FC} and β21,FC=(ΔtK)/ρˉs,FCn\beta_{21,FC}=(\Delta tK)/\bar{\rho}^{n}_{s,FC} with K is the momentum exchange coefficient. Similar derivation can be performed to computed the cell-center velocity increment leading to

(1+β12c−β12c−β21c1+β21c)(ΔUfcΔUsc)=(β12c(Usc∗−Ufc∗)β21c(Ufc∗−Usc∗))\begin{pmatrix} 1+\beta_{12c} & -\beta_{12c} \\ -\beta_{21c} & 1+\beta_{21c} \end{pmatrix} \begin{pmatrix} \Delta U_{fc} \\ \Delta U_{sc} \end{pmatrix} = \begin{pmatrix} \beta_{12c}(U^{*}_{sc}-U^{*}_{fc}) \\ \beta_{21c}(U^{*}_{fc}-U^{*}_{sc}) \end{pmatrix}

with β12c=(ΔtK)/ρˉfcn\beta_{12c}=(\Delta tK)/\bar{\rho}^{n}_{fc} and β21c=(ΔtK)/ρˉscn\beta_{21c}=(\Delta tK)/\bar{\rho}^{n}_{sc} and the cell-centered intermediate velocity can be calculated by

Ufc∗=Ufcn+Δt(−∇pfcn+1ρfcn+∇⋅τfcnρˉfcn+b)U^{*}_{fc}=U^{n}_{fc}+\Delta t\left(-\frac{\nabla p^{n+1}_{fc}}{\rho^{n}_{fc}}+\frac{\nabla\cdot\tau^{n}_{fc}}{\bar{\rho}^{n}_{fc}}+\boldsymbol{b}\right)
Usc∗=Uscn+Δt(∇⋅σcnρˉscn−∇pfcn+1ρs+b)(128)U^{*}_{sc}=U^{n}_{sc}+\Delta t\left(\frac{\nabla\cdot\sigma^{n}_{c}}{\bar{\rho}^{n}_{sc}}-\frac{\nabla p^{n+1}_{fc}}{\rho_{s}}+\boldsymbol{b}\right) \tag*{(128)}

For generalize multi materials i,j = 1:N, the linear equations is in the form:

(1+βij−βij−βji1+βji)(ΔUiΔUj)=(βij(Ui∗−Uj∗)βji(Uj∗−Ui∗))\begin{pmatrix} 1+\beta_{ij} & -\beta_{ij} \\ -\beta_{ji} & 1+\beta_{ji} \end{pmatrix} \begin{pmatrix} \Delta U_i \\ \Delta U_j \end{pmatrix} = \begin{pmatrix} \beta_{ij}(U^{*}_{i}-U^{*}_{j}) \\ \beta_{ji}(U^{*}_{j}-U^{*}_{i}) \end{pmatrix}

Similar approach applied for the energy exchange term leading to:

(1+ηij−ηij−ηji1+ηji)(ΔTiΔTj)=(ηij(Tin−Tjn)ηji(Tjn−Tin))\begin{pmatrix} 1+\eta_{ij} & -\eta_{ij} \\ -\eta_{ji} & 1+\eta_{ji} \end{pmatrix} \begin{pmatrix} \Delta T_i \\ \Delta T_j \end{pmatrix} = \begin{pmatrix} \eta_{ij}(T^{n}_{i}-T^{n}_{j}) \\ \eta_{ji}(T^{n}_{j}-T^{n}_{i}) \end{pmatrix}

with η\eta is the energy exchange coefficient.

References

  1. [1]D. Yuk, S. Yim, P.-F. Liu, Numerical modeling of submarine mass-movement generated waves using RANS model, Computers and Geosciences 32 (7) (2006) 927–935. doi:10.1016/j.cageo.2005.10.028. URL https://doi.org/10.1016/j.cageo.2005.10.028
  2. [2]S. Glimsdal, J.-S. L’Heureux, C. B. Harbitz, F. Løvholt, The 29th january 2014 submarine landslide at statland, norway—landslide dynamics, tsunami generation, and run-up, Landslides 13 (6) (2016) 1435–1444. doi:10.1007/s10346-016-0758-7. URL https://doi.org/10.1007/s10346-016-0758-7
  3. [3]S. Abadie, D. Morichon, S. Grilli, S. Glockner, Numerical simulation of waves generated by landslides using a multiple-fluid navier–stokes model, Coastal Engineering 57 (9) (2010) 779–794. doi:10.1016/j.coastaleng.2010.03.003. URL https://doi.org/10.1016/j.coastaleng.2010.03.003
  4. [4]M. Rauter, S. Viroulet, S. S. Gylfadóttir, W. Fellin, F. Løvholt, Granular porous landslide tsunami modelling – the 2014 lake askja flank collapse, Nature Communications 13 (1) (Feb. 2022). doi:10.1038/s41467-022-28296-7. URL https://doi.org/10.1038/s41467-022-28296-7
  5. [5]Q.-A. Tran, W. Solowski, Generalized interpolation material point method modelling of large deformation problems including strain-rate effects – application to penetration and progressive failure problems, Computers and Geotechnics 106 (2019) 249–265. doi:10.1016/j.compgeo.2018.10.020. URL https://doi.org/10.1016/j.compgeo.2018.10.020
  6. [6]T. Capone, A. Panizzo, J. J. Monaghan, SPH modelling of water waves generated by submarine landslides, Journal of Hydraulic Research 48 (sup1) (2010) 80–84. doi:10.1080/00221686.2010.9641248. URL https://doi.org/10.1080/00221686.2010.9641248
  7. [7]X. Zhang, E. Oñate, S. A. G. Torres, J. Bleyer, K. Krabbenhoft, A unified lagrangian formulation for solid and fluid dynamics and its possibility for modelling submarine landslides and their consequences, Computer Methods in Applied Mechanics and Engineering 343 (2019) 314–338. doi:10.1016/j.cma.2018.07.043. URL https://doi.org/10.1016/j.cma.2018.07.043
  8. [8]R. Dey, B. C. Hawlader, R. Phillips, K. Soga, Numerical modelling of submarine landslides with sensitive clay layers, Géotechnique 66 (6) (2016) 454–468. doi:10.1680/jgeot.15.p.111. URL https://doi.org/10.1680/jgeot.15.p.111
  9. [9]S. Bandara, K. Soga, Coupling of soil deformation and pore fluid flow using material point method, Computers and Geotechnics 63 (2015) 199–214. doi:10.1016/j.compgeo.2014.09.009. URL https://doi.org/10.1016/j.compgeo.2014.09.009
  10. [10]A. P. Tampubolon, T. Gast, G. Klár, C. Fu, J. Teran, C. Jiang, K. Museth, Multi-species simulation of porous sand and water mixtures, ACM Transactions on Graphics 36 (4) (2017) 1–11. doi:10.1145/3072959.3073651. URL https://doi.org/10.1145/3072959.3073651
  11. [11]A. S. Baumgarten, K. Kamrin, A general constitutive model for dense, fine-particle suspensions validated in many geometries, Proceedings of the National Academy of Sciences 116 (42) (2019) 20828–20836. doi:10.1073/pnas.1908065116. URL https://doi.org/10.1073/pnas.1908065116
  12. [12]Q.-A. Tran, W. Sołowski, Temporal and null-space filter for the material point method, International Journal for Numerical Methods in Engineering 120 (3) (2019) 328–360. doi:10.1002/nme.6138. URL https://doi.org/10.1002/nme.6138
  13. [13]X. Zheng, F. Pisanò, P. J. Vardon, M. A. Hicks, An explicit stabilised material point method for coupled hydromechanical problems in two-phase porous media, Computers and Geotechnics 135 (2021) 104112. doi:10.1016/j.compgeo.2021.104112. URL https://doi.org/10.1016/j.compgeo.2021.104112
  14. [14]Q. A. Tran, W. Sołowski, M. Berzins, J. Guilkey, A convected particle least square interpolation material point method, International Journal for Numerical Methods in Engineering 121 (6) (2019) 1068–1100. doi:10.1002/nme.6257. URL https://doi.org/10.1002/nme.6257
  15. [15]J.-S. Chen, M. Hillman, S.-W. Chi, Meshfree methods: Progress made after 20 years, Journal of Engineering Mechanics 143 (4) (Apr. 2017). doi:10.1061/(asce)em.1943-7889.0001176 URL https://doi.org/10.1061/(asce)em.1943-7889.0001176
  16. [16]B. A. Kashiwa, A multifield model and method for fluid-structure interaction dynamics, Tech. Rep. LA-UR-01-1136, Los Alamos National Laboratory (2001).
  17. [17]J. Guilkey, T. Harman, B. Banerjee, An eulerian–lagrangian approach for simulating explosions of energetic devices, Computers and Structures 85 (11) (2007) 660 – 674. doi:https://doi.org/10.1016/j.compstruc.2007.01.031. URL http://www.sciencedirect.com/science/article/pii/S0045794907000429
  18. [18]A. S. Baumgarten, B. L. Couchman, K. Kamrin, A coupled finite volume and material point method for two-phase simulation of liquid–sediment and gas–sediment flows, Computer Methods in Applied Mechanics and Engineering 384 (2021) 113940. doi:10.1016/j.cma.2021.113940. URL https://doi.org/10.1016/j.cma.2021.113940
  19. [19]S. Bardenhagen, J. Guilkey, K. Roessig, J. Brackbill, W. Witzel, J.C.Foster, An improved contact algorithm for the material point method and application to stress propagation in granular material, CMES-Computer Modeling in Engineering and Sciences 2 (2001) 509–522. doi:10.3970/cmes.2001.002.509.DOI
  20. [20]J. A. M. K. R. Beetstra, M. A. van der Hoef, Drag force of intermediate reynolds number flow past mono- and bidisperse arrays of spheres, Fluid Mechanics and Transport Phenomena 53 (2) (2007) 489 – 501. doi:https://doi.org/10.1002/aic.11065.
  21. [21]R. W. Stewart, The air-sea momentum exchange, Boundary-Layer Meteorology 6 (1-2) (1974) 151–167. doi:10.1007/bf00232481. URL https://doi.org/10.1007/bf00232481
  22. [22]S. G. B. amd E. M. Kober, The generalized interpolation material point method, Computer Modeling in Engineering and Sciences 5 (2004) 477–496. doi:10.1016/j.compgeo.2021.104199. URL https://doi.org/10.3970/cmes.2004.005.477
  23. [23]S. G. Amiri, E. Taheri, A. Lavासन, A hybrid finite element model for non-isothermal two-phase flow in deformable porous media, Computers and Geotechnics 135 (2021) 104199. doi:10.1016/j.compgeo.2021.104199. URL https://doi.org/10.1016/j.compgeo.2021.104199
  24. [24]S. A. R. C. Mariotti; P. Heinrich, Numerical simulation of submarine landslides and their hydraulic effects, Journal of Waterway, Port, Coastal, and Ocean Engineering 123 (4) (1997). doi:https://doi.org/10.1061/(ASCE)0733-950X(1997)123:4(149).
  25. [25]D. Drumheller, On theories for reacting immiscible mixtures, International Journal of Engineering Science 38 (3) (2000) 347 – 382. doi:https://doi.org/10.1016/S0020-7225(99)00047-6. URL http://www.sciencedirect.com/science/article/pii/S0020722599000476
  26. [26]S. Hassanizadeh, Derivation of basic equations of mass transport in porous media, part1: Macroscopic balance laws, Advances in Water Resources 9 (1986) 196–206. doi:https://doi.org/10.1016/0309-1708(86)90024-2.

Paper details

vlnc:W_pqxhsg8k
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 9

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Mathematics

Not recorded for this paper

View statement
Looking for related papers…
Contents