betaFeedback

WorksPhysics and Astronomy

Stabilization of Yih's Viscosity Jump Interface in a Channel

Abstract

Two immiscible viscous fluids in pressure-driven channel flow can be unstable through their interface when their viscosities differ, at arbitrarily small Reynolds number — the instability Yih found in 1967. The unstable state is the interface itself: a curve inside the domain, separating the two fluids, whose displacement is governed by a partial differential equation of its own and which moves the fluid domain with it. Actuation is at one wall only, so the state to be controlled is reached across a fluid. We stabilize this interface at any rate below the limit set by the streamwise mean flow, by static feedback of the two velocity components of that wall, through a Fredholm backstepping transformation acting jointly on the two layers. The target is the two-fluid Stokes problem, shifted, with the transmission of stress between the fluids kept and the coupling of the interface into them removed. Two findings about the two-fluid spectrum carry the design: joined at the interface, the eigenvalue sequences of the two layers, which collide for a dense set of layer ratios when the layers are uncoupled, avoid each other uniformly, so no degeneracy has to be assigned; and the slowest mode left to viscosity is not a bulk mode but the capillary relaxation of the interface, whose rate is linear rather than quadratic in the wavenumber, which sets the band of actuated wavenumbers. The controller is tested on the nonlinear two-fluid channel, switched on against a saturated interfacial wave.

Introduction

Problem

Two incompressible fluids of different viscosity, stacked in a plane channel and driven by a pressure gradient, flow with a piecewise parabolic profile whose slope jumps at the interface. Yih [18] showed that this viscosity jump can destabilize long interfacial waves at arbitrarily small Reynolds number, depending on the viscosity ratio and the layer thicknesses. The mode is not a mode of either fluid. It is carried by the displacement of the interface, which is an unknown of the problem in its own right, and it feeds back into the fluids through a single term in the tangential-velocity condition at the interface. The instability underlies the breakdown of lubricated transport of viscous oil by a water layer, the wave regimes of stratified oil–water pipelines, and the interfacial defects of coextruded films and coating flows — configurations in which the shape of the interface is the product.

Literature

The interface is a moving boundary. Backstepping feedback stabilization of moving-boundary PDE systems has been developed over the past decade for a thermal phase-change front (the Stefan problem) [11], a piston between two columns of compressible gas [10], the growth cone of a neuron [5], and the shock front of a traffic wave [19]. A string whose endpoint moves is controlled from the boundary in [6, 7], and a point mass moving in a viscous fluid is steered by a force on the mass in [2]. In each of these the domain is one-dimensional and the moving boundary is a point, whose position is governed by an ordinary differential equation coupled to the PDE through its boundary values. A subsystem joined to others at both of its ends is a sandwich system: in [16] an ODE sandwiched between two PDEs, the coupled hyperbolic PDEs of a cable on one side and the transport PDE of a sensor delay on the other, and in [17] a PDE sandwiched between two ODEs, with the PDE domain varying in time along a prescribed law. The plant here has that structure with each part one dimension higher: two-dimensional fluids on either side and a one-dimensional interface between them. The domain variation is not prescribed either, since the interface is the state that moves the boundaries of the two fluid domains. The present problem is the next case in that sequence: the domain is two-dimensional, the moving boundary is a curve, and its position is governed by a partial differential equation of its own — the kinematic condition — coupled to the fluids along its whole length.

Outside of backstepping, Munteanu [13] posed and solved the boundary stabilization problem for two viscous incompressible fluids in a channel: the Navier–Stokes equations coupled to a convective Cahn–Hilliard equation for the relative density of one species, with the Poiseuille profile as the target flow, stabilized by feedback of the tangential velocity at both walls, the feedback given in explicit form. There the two fluids are described by an order parameter and the interface between them is a diffuse layer of positive thickness, so the fluid domain is fixed and its boundary is the two walls. The present paper treats the same two fluids with the interface sharp, as a moving boundary carrying the state.

Controllability of fluid–structure interactions, in which an elastic structure moves inside a fluid, has been studied [9, 1], and feedback stabilization of a fluid–beam system by a Riccati-based design in [14]. An interface between two fluids has no structure of its own: it carries no stiffness and no mass, only capillarity, and it moves because the fluids move.

1.3. This Paper. Two features set the problem tackled in this paper apart from those it descends from. Unlike single-fluid Poiseuille flow [15, 12], which is unstable only above a Reynolds number in the thousands, the two-fluid channel can be unstable at arbitrarily small Reynolds number, so the instability is not a high-Reynolds-number effect to be suppressed but a low-Reynolds-number one that the equilibrium profile carries into every regime. And unlike the moving-boundary systems in [11, 10, 5, 19], where the boundary follows the interior fields and the interior is where any instability would arise, here the instability originates at the boundary and is manifested there: the unstable mode is the interface displacement itself, and the fluids serve only to transmit it.

This paper controls that instability from the wall, with the two velocity components of the upper wall, by the Fredholm backstepping design developed for single-fluid Poiseuille flow in [12], which carries the rapid stabilization of [3, 4] to that plant. Everything the design uses is taken from there: the Stokes problem as target, the finite-rank pre-feedback through the normal wall velocity that makes every mode controllable from the tangential one, the Riesz basis of the plant obtained by perturbation from the target’s, and the Fredholm transformation built on that basis. None of it is re-derived here; where a proof carries over it is cited, and where the second fluid changes it — the spectrum, the wall coefficients, the slow mode, the mean flow — it is proved. What is added is the object: an interface between two fluids, an unstable state attached to a curve inside the domain and governed by its own equation, which [12] does not contain.

The lower wall is unactuated. So the interface, the object to be controlled, sits at an interior point of the channel and is reached only across the actuated fluid. Per wavenumber, the linearized plant is a pair of fourth-order Orr–Sommerfeld operators on the two layers, joined at the interface by four transmission conditions, with the interface displacement as an additional scalar state attached there. One of the transmission conditions carries a time derivative when the densities differ. The unstable coupling of the interface into the fluids is of rank one.

Contributions

  • Rapid stabilization of a PDE-governed moving boundary. The Yih interfacial instability of two fluids across a viscosity jump in a channel is stabilized at every prescribed rate below the mean-flow controllability limit, with wall actuation in one of the two fluids, the other wall being unactuated. Where the two fluids in a channel have been stabilized with the interface diffuse [13], on a fixed domain and at an unprescribed rate, here the interface is sharp: the state includes its displacement, the fluid domain moves with it, and the moving boundary is governed by a partial differential equation of its own in one space dimension rather than by an ordinary differential equation at a point, as in [11, 10, 5, 19]. Every mode that deforms the interface admits an arbitrary rate; what limits the achievable rate is the streamwise mean flow alone, which one wall velocity can fail to reach, and that limit is shown to be attainable and to tighten with the Reynolds number. This is possible because the interface, although an interior object reached only across the actuated fluid, is a single scalar per wavenumber whose only destabilizing coupling to the fluids is of rank one, and a Fredholm transformation acting jointly on the two layers removes it while leaving the transmission conditions between the layers intact.

Three mathematical obstacles stood in the way, met by the following.

  • Coupling two layers simplifies their spectrum. The interface does not make the spectrum harder; it makes it simpler. Two viscous layers considered separately have eigenvalue sequences that come arbitrarily close for a dense set of viscosity and thickness ratios, and a design would then have to assign near-degenerate pairs. Joined at the interface, the sequences avoid each other uniformly: at every admissible parameter value the high modes of the coupled problem are simple and uniformly separated, and the one-fluid Fredholm construction applies to the two-fluid channel without a new spectral device.

  • What an interfacial target may delete. The target of the design is the two-fluid Stokes problem itself, shifted and with its finitely many low eigenvalues separated by a finite-rank term, with the viscosity jump kept in its transmission conditions. Deleting that jump makes the target dissipative for a reason unrelated to the physics; keeping it makes the dissipation the strain-rate integral of the two fluids. This identifies what a backstepping target for an interfacial problem may delete — the coupling of the interface displacement into the fluids — and what it may not — the transmission of stress between them.

  • Capillary relaxation sets the actuated band. What a wall feedback acting on finitely many wavenumbers must outrun is not the viscous decay of the fluids but the capillary relaxation of the interface, which is slower: it is linear in the wavenumber where the bulk modes decay quadratically. Computing that rate with its constant, from the mobility of a viscous interface, makes the controlled band explicit and linear in the requested rate.

The main theorem is stated in Section 3; the design and its analysis follow, in the order of the dependencies among them.

Two-Fluid Channel and Its Linearization

Fluid 1 occupies 0<y<d+η(t,x)0<y<d+\eta(t,x) and fluid 2 occupies d+η(t,x)<y<1d+\eta(t,x)<y<1, both LL-periodic in xx, with densities ρj\rho_j, viscosities μj\mu_j, and the interface at y=d+η(t,x)y=d+\eta(t,x). Lengths are scaled by the channel height HH, velocities by the centerline speed UeU^e of the single-fluid Poiseuille profile with the same pressure gradient, pressure by ρ1(Ue)2\rho_1(U^e)^2, and ρ1=μ1=1\rho_1=\mu_1=1 in nondimensional terms. With

Re⁡=ρ1UeHμ1,M=μ2μ1,Σ=σρ1(Ue)2H,G=qH(Ue)2,(1)\operatorname{Re}=\frac{\rho_1 U^e H}{\mu_1},\qquad M=\frac{\mu_2}{\mu_1},\qquad\Sigma=\frac{\sigma}{\rho_1(U^e)^2H},\qquad G=\frac{qH}{(U^e)^2}, \tag*{(1)}

the fluids obey, in their respective domains,

∂xuj+∂yvj=0,(2)\partial_x u_j+\partial_y v_j=0, \tag*{(2)}
ρj(∂tuj+uj∂xuj+vj∂yuj)=−∂xpj+μjRe⁡(∂x2+∂y2)uj,(3)\rho_j\left(\partial_tu_j+u_j\partial_xu_j+v_j\partial_yu_j\right)=-\partial_xp_j+\frac{\mu_j}{\operatorname{Re}}\left(\partial_x^2+\partial_y^2\right)u_j, \tag*{(3)}
ρj(∂tvj+uj∂xvj+vj∂yvj)=−∂ypj+μjRe⁡(∂x2+∂y2)vj−ρjG,(4)\rho_j\left(\partial_tv_j+u_j\partial_xv_j+v_j\partial_yv_j\right)=-\partial_yp_j+\frac{\mu_j}{\operatorname{Re}}\left(\partial_x^2+\partial_y^2\right)v_j-\rho_jG, \tag*{(4)}

with no slip at the unactuated wall and the two actuated components at the upper wall,

u1(t,x,0)=v1(t,x,0)=0,(5)u_1(t,x,0)=v_1(t,x,0)=0, \tag*{(5)}
u2(t,x,1)=Uc(t,x),v2(t,x,1)=Vc(t,x),(6)u_2(t,x,1)=U_c(t,x),\qquad v_2(t,x,1)=V_c(t,x), \tag*{(6)}

and at the interface y=d+η(t,x)y=d+\eta(t,x),

ηt+ujηx=vj,[u1−u2]=[v1−v2]=0,(T2−T1)n=Σκn,(7)\eta_t+u_j\eta_x=v_j,\qquad[u_1-u_2]=[v_1-v_2]=0,\qquad(T_2-T_1)n=\Sigma\kappa n, \tag*{(7)}
Tj=−pjI+μjRe⁡(∇uj+∇ujT),(8)T_j=-p_j I+\frac{\mu_j}{\operatorname{Re}}\left(\nabla u_j+\nabla u_j^{\mathsf T}\right), \tag*{(8)}
n=(−ηx,1)1+ηx2,κ=−ηxx(1+ηx2)3/2.(9)n=\frac{(-\eta_x,1)}{\sqrt{1+\eta_x^2}},\qquad\kappa=-\frac{\eta_{xx}}{(1+\eta_x^2)^{3/2}}. \tag*{(9)}

Here (8)–(9) define the stress and the normal and curvature of the graph y=d+ηy=d+\eta. The mean flux is held at its equilibrium value.

The flat interface η≡0\eta\equiv0 with vj≡0v_j\equiv0, uj=Uj(y)u_j=U_j(y), and pj=−Px+pI−ρjG(y−d)p_j=-Px+p_I-\rho_jG(y-d), normalized by PRe⁡=8P\operatorname{Re}=8, gives

U1(y)=4y(G0−y),U2(y)=4M(1−y)(1+y−G0),(10)U_1(y)=4y(G_0-y),\qquad U_2(y)=\frac{4}{M}(1-y)(1+y-G_0), \tag*{(10)}
G0=1−(1−M)d21−(1−M)d,(11)G_0=\frac{1-(1-M)d^2}{1-(1-M)d}, \tag*{(11)}

continuous at y=dy=d with μ1U1′(d)=μ2U2′(d)\mu_1U_1'(d)=\mu_2U_2'(d), so that the slope jumps by the factor 1/M1/M, and with μ1U1′′=μ2U2′′=−8\mu_1U_1''=\mu_2U_2''=-8. The interface speed and slope are

UI=U1(d)=4Md(1−d)1−(1−M)d,U1′(d)=4[1−2d+(1−M)d2]1−(1−M)d.(12)U_I=U_1(d)=\frac{4Md(1-d)}{1-(1-M)d},\qquad U_1'(d)=\frac{4[1-2d+(1-M)d^2]}{1-(1-M)d}. \tag*{(12)}

Integrals over a layer are written out, ∫0d\int_0^d for fluid 1 and ∫d1\int_d^1 for fluid 2, and ∑jIj\sum_j I_j abbreviates their sum. Linearizing about (10), transferring the interface conditions to y=dy=d, expanding in e2πikxe^{2\pi ikx} with k=m/Lk=m/L, and eliminating the streamwise velocity and the pressure through uj=i2πk∂vju_j=\frac{i}{2\pi k}\partial v_j and the streamwise momentum equation, as in [12], gives the plant per wavenumber in the normal velocities vj(y,t)v_j(y,t) and the interface displacement η(t)\eta(t). With E:=∂2−4π2k2\mathsf{E}:=\partial^2-4\pi^2k^2, ∂:=∂y\partial:=\partial_y,

References

  1. [1]M. Boulakia and A. Osses, Local null controllability of a two-dimensional fluid–structure interaction problem, ESAIM Control Optim. Calc. Var. 14 (2008) 1–42.
  2. [2]N. Cîndea, S. Micu, I. Roventa, and M. Tucsnak, Particle supported control of a fluid–particle system, J. Math. Pures Appl. 104 (2015) 311–353.
  3. [3]J.-M. Coron and Q. Lü, Local rapid stabilization for a Korteweg–de Vries equation with a Neumann boundary control on the right, J. Math. Pures Appl. 102 (2014) 1080–1120.arxiv.org/abs/1311.4031
  4. [4]J.-M. Coron and Q. Lü, Fredholm transform and local rapid stabilization for a Kuramoto–Sivashinsky equation, J. Differential Equations 259 (2015) 3683–3729.arxiv.org/abs/1501.02042
  5. [5]C. Demir, S. Koga, and M. Krstic, Neuron growth control and estimation by PDE backstepping, Automatica 165 (2024) 111669.DOI
  6. [6]M. Gugat, Optimal energy control in finite time by varying the length of the string, SIAM J. Control Optim. 46 (2007) 1705–1725.DOI
  7. [7]M. Gugat, Optimal boundary feedback stabilization of a string with moving boundary, IMA J. Math. Control Inform. 25 (2008) 111–121.DOI
  8. [8]A. P. Hooper and W. G. C. Boyd, Shear-flow instability at the interface between two viscous fluids, J. Fluid Mech. 128 (1983) 507–528.DOI
  9. [9]O. Imanuvilov and T. Takahashi, Exact controllability of a fluid–rigid body system, J. Math. Pures Appl. 87 (2007) 408–437.
  10. [10]I. Karafyllis and M. Krstic, Global stabilization of compressible flow between two moving pistons, SIAM J. Control Optim. 60 (2022) 1117–1142.arxiv.org/abs/2104.09153
  11. [11]S. Koga, M. Diagne, and M. Krstic, Control and state estimation of the one-phase Stefan problem via backstepping design, IEEE Trans. Automat. Control 64 (2019) 510–525.arxiv.org/abs/1703.05814
  12. [12]M. Krstic, Fredholm backstepping with Heymann pre-feedback for Navier–Stokes 2D channel, Mathematics of Control, Signals, and Systems, under review; https://arxiv.org/abs/2609.19331, 2026.
  13. [13]I. Munteanu, Boundary stabilizing actuators for multi-phase fluids in a channel, J. Differential Equations 285 (2021) 175–210.
  14. [14]J.-P. Raymond, Feedback stabilization of a fluid–structure model, SIAM J. Control Optim. 48 (2010) 5398–5443.DOI
  15. [15]R. Vazquez and M. Krstic, A closed-form feedback controller for stabilization of the linearized 2-D Navier–Stokes Poiseuille system, IEEE Trans. Automat. Control 52 (2007) 2298–2312.DOI
  16. [16]J. Wang and M. Krstic, Delay-compensated control of sandwiched ODE–PDE–ODE hyperbolic systems for oil drilling and disaster relief, Automatica 120 (2020) 109131.arxiv.org/abs/1910.05948
  17. [17]J. Wang and M. Krstic, Output-feedback control of an extended class of sandwiched hyperbolic PDE–ODE systems, IEEE Trans. Automat. Control 66 (2021) 2588–2603.DOI
  18. [18]C.-S. Yih, Instability due to viscosity stratification, J. Fluid Mech. 27 (1967) 337–352.
  19. [19]H. Yu, M. Diagne, L. Zhang, and M. Krstic, Bilateral boundary control of moving shockwave in LWR model of congested traffic, IEEE Trans. Automat. Control 66 (2021) 1429–1436.arxiv.org/abs/1904.04303

Paper details

vlnc:W_q2yc6eme
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 3

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Claude, ChatGPT

View statement
Looking for related papers…
Contents