WorksPhysics and Astronomy
In-Plane Q Anisotropy of Higher-Order XBARs in 128°Y-Cut Lithium Niobate
Abstract
128Y-cut lithium niobate (LN) laterally field-excited higher-order antisymmetric bulk acoustic resonators (XBARs) have attracted interest for high-frequency acoustic devices thanks to their high electromechanical coupling coefficient (), high quality factor () from low metal coverage ratio, and thickness-defined resonant frequency. So far, the in-plane orientation of these resonators is commonly chosen to maximize , thereby maximizing bandwidth. More recently, in-plane-rotated XBARs in 128Y-cut LN have been built to provide greater design flexibility in filter synthesis. However, the in-plane anisotropy of has been far less explored. This leaves an important gap in understanding whether the propagation direction that determines also affects . In this work, we investigate the anisotropic of higher-order antisymmetric modes (namely, A, A, and A) in 500-nm-thick 128Y-cut LN on Si. By characterizing resonator performance in various in-plane orientations, we observe that both Bode and show minimum values at 90 to the material x-axis and maximum values around 0, following a trend similar to . The A, A, and A modes around 10.4, 17, and 24 GHz exhibit averaged Bode / values of 735/556, 204/149, and 59/37, respectively. At 90, the average Bode values are reduced to 66, 9, and 12. Finite element analysis (FEA) results suggest that the orientation-dependent degradation of near 90 is associated with stronger transverse displacement near the inactive and anchor regions, resulting in enhanced energy leakage. These results reveal an orientation-dependent loss pathway in 128Y-cut LN XBARs and provide design guidance for jointly optimizing and .
Figure 1.
Introduction
Acoustic resonators are essential components in modern electronic systems, including radio-frequency (RF) front-end filters [1], oscillators [2], sensors [3], and emerging quantum acoustic platforms [4]. Their compact footprint, frequency scalability, and efficient electromechanical transduction make them attractive for highly integrated signal-processing systems [5], [6]. Among various piezoelectric materials, lithium niobate (LN) has emerged as a promising platform for high-performance acoustic resonators due to its strong piezoelectricity and large electromechanical coupling coefficient () [7, 8, 9]. In particular, 128°Y-cut LN has been widely used for laterally excited bulk acoustic resonators (XBARs), where strong coupling has enabled high-frequency acoustic devices [10, 11, 12].
As wireless communication systems continue to evolve toward higher frequencies and wider bandwidths, both and quality factor () become critical performance metrics [13, 14, 15, 16]. While determines the energy transduction efficiency and achievable bandwidth, governs acoustic energy dissipation and directly affects insertion loss, frequency selectivity, and overall resonator efficiency [8], [17]. Therefore, understanding how both and vary with device design and material orientation is essential for optimizing LN acoustic resonators [18, 19, 20, 21].
Because LN is strongly anisotropic, the in-plane propagation orientation has been widely used as a key design parameter for improving resonator performance. In 128°Y-cut LN, previous studies have primarily utilized this anisotropy to identify orientations that maximize , particularly for high-coupling XBARs [10], [22]. However, optimizing alone does not necessarily guarantee high .
Recent studies have begun to show that acoustic dissipation in LN resonators can also depend strongly on propagation orientation. For example, anisotropic behavior has been reported in X-cut LN S resonators [19] and in 36°Y-cut
This work was supported by the National Science Foundation (NSF) under CAREER Award No. 2339731, and a graduate fellowship from the Ministry of National Defense of the Republic of Korea.
Byeongjin Kim, Ian Anderson, and Ruochen Lu are with the Electrical and Computer Engineering Department, The University of Texas at Austin (email: [email protected]). Highlights
Anisotropic of higher-order antisymmetric modes (//) measured in 128°Y-cut LN on Si
Averaged Bode of 735/204/59 (//) follows , dropping sharply to 66/9/12 at 90°
FEA suggests that reduced near 90° is consistent with enhanced transverse motion near the anchors
Index Terms— 128°Y-cut lithium niobate, anchor loss, anisotropy, higher-order antisymmetric mode, laterally excited bulk acoustic resonator (XBAR), quality factor
LN SH resonators [23]. In these platforms, the resonance quality factor was shown to vary with in-plane propagation angle, indicating that acoustic loss is also governed by crystal anisotropy. These studies suggest that maximizing alone is insufficient for realizing optimal resonator performance and that orientation-dependent loss mechanisms must also be considered. Nevertheless, a systematic investigation of anisotropic in 128°Y-cut LN XBARs remains limited, despite the importance of this cut for high-frequency, high-coupling acoustic devices.
In this work, we experimentally investigate the anisotropic of higher-order antisymmetric modes in 500-nm-thick 128°Y-cut LN on Si. By characterizing , , and modes as a function of in-plane propagation orientation, we observe that both Bode and 3dB at the parallel resonant frequency () follow a trend similar to , with minimum values at 90° and maximum values at 0° and 180°. The , , and modes around 10.4, 17, and 24 GHz exhibit averaged Bode / values of 735/546, 204/149, and 59/37, respectively. At 90°, the average Bode values are reduced to 66, 9, and 12 for the , , and modes, while cannot be reliably extracted because of the weak resonance response. FEA results further indicate that unintended transverse displacement is strongest at 90°, particularly near the anchors, leading to increased acoustic energy leakage and reduced . These results suggest that the orientation-dependent degradation of in 128°Y-cut LN XBARs is strongly influenced by transverse mode deformation and anchor-region leakage, providing design guidelines for simultaneously optimizing and .
Design and Simulation
To investigate the orientation-dependent behavior of 128°Y-cut LN resonators, the device geometry was designed as shown in Fig. 1(a). The resonator consists of interdigitated transducers (IDTs) patterned on a suspended 500-nm-thick LN resonant body with release windows defined around the active region. A series of MEMS resonators are arranged with respect to the material -axis, and the in-plane angle is defined as the counterclockwise rotation angle from the -axis. The key design parameters, including resonator length (), resonator width (), electrode width (), gap width (), window width (), and device number (), are summarized in the table in Fig. 1(a). The resonator array was designed to suppress spurious modes and obtain cleaner resonance responses from the intended antisymmetric modes, enabling a more reliable evaluation of anisotropic [24, 25].
Figure 1 (PDF p. 2). (a) Schematic of the spurious-mode-suppressed 128°Y-cut LN resonator design with key dimensions summarized in the table. (b) Simulated wideband admittance response of the resonator array with representative displacement mode shapes.
| Sym. | Parameter | Value |
| Resonator length | 72–152 μm | |
| Resonator width | 10 μm | |
| Electrode width | 2–3 μm | |
| Gap width | 1–2 μm | |
| Window width | 8 μm | |
| Device number | 10 |
Table 1.
Fig. 1(b) shows the simulated wideband admittance response of the resonator array together with representative displacement mode shapes. Clear resonances are observed for the , , and modes at approximately 10.6, 17.4, and 24.4 GHz, respectively, each showing a well-defined thickness-shear displacement profile. In contrast, the mode exhibits multiple spurious responses around the main resonance. This is likely because the duty cycle, defined as the ratio of the electrode width to the IDT period, and the LN thickness are not optimized to match the dispersion between the metalized and non-metalized regions of the mode in the present stack. The resulting velocity mismatch can perturb the lateral mode profile and introduce multiple higher-order spurious responses around the main resonance [26, 27]. Therefore, the mode is excluded from the anisotropic analysis, and the following study focuses on the , , and higher-order antisymmetric modes, which provide clearer modal responses.
The effective in spurious-free resonators with high can be approximated by:
where and are the simulated series and parallel resonant frequencies. This -based is equivalent to the value later extracted from the modified Butterworth–Van Dyke (mBVD) model. However, because routing resistance, parasitic capacitance, and other high-frequency parasitics can distort the apparent and spacing, the measured values are extracted using mBVD fitting [28, 29, 30].
For the higher-order antisymmetric modes in 128°Y-cut LN, the excitation is mainly associated with the piezoelectric stress coefficient , which varies strongly with in-plane propagation angle [10, 22]. This angular dependence leads to the trend shown later in Figure 8, where reaches its minimum at 90° and maximum values at 0° and 180°. Consistent with this trend, the simulated admittance responses in Figure 2 show that, for the A, A, and A modes, and become closer as the propagation angle approaches 90°, indicating reduced .
Figure 2. Simulated admittance responses of the 128°Y-cut LN resonators at different in-plane angles from 10° to 170°: (a) A mode; (b) A mode; (c) A mode. The reduction in toward 90° is observed for all three modes.
Figure 8. Extracted Bode , , and mBVD-fitted as functions of in-plane angle for the (a) A, (b) A, and (c) A modes.
Although the simulations capture the anisotropic coupling trend, the experimentally measured is difficult to predict in advance because it depends on multiple loss contributions. The total quality factor is determined by the ratio of stored to dissipated energy and can be expressed as
where and are the stored and dissipated energy per cycle, respectively, and , , and correspond to anchor loss, thermoelastic damping (TED), and other loss mechanisms, respectively [31]. Since these loss contributions depend on material properties, electrode conditions, fabrication variations, and resonator geometry, predefined material quality factors were assigned to LN and the electrodes as practical damping parameters, with and , to obtain finite simulated admittance responses. These values are used only to compare relative resonance behavior and mode shapes, while the actual anisotropic must be determined experimentally.
Using this finite element analysis (FEA) framework, the simulated mode-shape results in Figure 3 further clarify the orientation-dependent deformation of the A mode. Figure 3(a) shows the unit-cell displacement and stress distribution, confirming that the intended mode is dominated by thickness-shear deformation. The enlarged top-view displacement profiles in Figure 3(b) reveal a clear orientation-dependent deformation behavior. As the in-plane propagation angle increases from 10° to 70° and approaches 90°, the unintended transverse displacement component, corresponding to the -direction, becomes increasingly pronounced. The 90° case is not included in Figure 3(b) because a well-defined A resonance could not be identified at this orientation. Figure 3(a) and Figure 3(b) were obtained from a periodic active-region model, which does not include the inactive or anchor regions. Therefore, these profiles are used to identify orientation-dependent transverse deformation, not to directly calculate anchor loss or absolute . To provide a more quantitative FEM comparison, additional finite one-pair-IDT resonator simulations were performed for the A3, A5, and A7 modes at in-plane angles from to in increments. The simulated was extracted from the admittance response and is shown in Figure 3(c), while the corresponding one-pair-IDT resonator model and anchor-region displacement fields are further examined in Figure 10. Data points for which the resonance was too weak to reliably extract the were omitted. The reduced at orientations with larger transverse deformation indicates that this deformation can couple to the inactive and anchor regions in the finite resonator, leading to enhanced acoustic energy leakage.
Figure 3. Simulated A mode shape and orientation-dependent deformation of the 128°Y-cut LN resonator: (a) unit-cell displacement and stress distributions; (b) enlarged top view displacement profiles with deformation at in-plane angles of 10°, 30°, 50°, and 70°; (c) simulated of the A, A, and A modes obtained from a finite one-pair-IDT resonator model at different in-plane angles.
Figure 10. Simulated displacement distributions of the A mode evaluated at the parallel resonance frequency (): (a) overall displacement profile of a one-pair-IDT resonator; (b) enlarged views of the anchor region at in-plane angles of 10°, 30°, 50°, and 70°, showing enhanced displacement leakage toward the anchor as the in-plane angle approaches 90°.
These simulation results motivate the experimental investigation of resonators with different in-plane propagation orientations. While Figure 2 shows that decreases toward , Figure 3 suggests that the unintended transverse displacement becomes stronger and the simulated decreases in the same angular range. Therefore, measuring the actual resonator responses across different orientations is necessary to determine whether the anisotropic trend is accompanied by the anisotropic coupling trend and to clarify the dominant loss behavior in 128°Y-cut LN XBARs.
Fabrication and Measurement
XBAR resonator arrays were fabricated from 500-nm-thick 128°Y-cut LN on Si substrates provided by NGK Corporation. Figure 4(a) shows the fabrication flow of the suspended resonators. First, fine IDT electrodes were defined by photolithography using an MA8 mask aligner, followed by 50 nm Pt deposition using e-beam evaporation and lift-off in PG remover with sonication. A second photolithography step was then performed to define the buslines and probing pads, followed by 80 nm Au deposition and lift-off. After metal patterning, release windows were defined by photolithography and etched through the LN layer using ion milling. Finally, the underlying Si was removed using XeF isotropic etching to form suspended 128°Y-cut LN resonators. Figure 4(b) shows optical micrographs of the fabricated resonators. Four resonator designs, labeled A–D, were fabricated by varying the resonator length and electrode width. For each design, devices were arranged at different in-plane propagation angles from to in increments, measured with respect to the material -axis. This design set enables statistical comparison of resonators with different dimensions at each propagation orientation, allowing the anisotropic trend to be evaluated more reliably.
Figure 4. (a) Fabrication flow of the suspended 128°Y-cut LN resonators. (b) Optical micrographs of fabricated resonators with different resonator lengths and electrode widths.
The measured admittance and Bode responses shown in Figure 5 and Figure 6 were obtained from Design A, whose complete structural parameters are summarized in Figure 4. Therefore, the resonators compared across different in-plane angles in these figures have identical geometry, with µm and µm. The Bode was extracted using the improved -parameter-based method after converting the measured admittance response to {[32]}. Figure 5(a) shows the measured wideband admittance responses of the fabricated resonators at different in-plane angles from to . The enlarged measured admittance responses of the A, A, and A modes around 10.4, 17, and 24 GHz are shown in Figure 5(b), (Figure 5d), and (Figure 5f), respectively, while the corresponding conductance responses are presented in Figure 5(c), (Figure 5e), and (Figure 5g). Compared with the admittance, the conductance provides a clearer visualization of the resonance linewidth, peak strength, and possible lossy or spurious responses, particularly at weak-coupling orientations. As the propagation angle approaches , the conductance peaks become progressively weaker and broader before eventually becoming indistinguishable from the background response. The increased resonance linewidth observed in the conductance responses is consistent with the reduction in the measured Bode shown in Figure 6. Small differences between the measured resonance frequencies and the simulated values, as well as device-to-device frequency variations, are mainly attributed to thickness nonuniformity within the same LN-on-Si sample. As expected from the simulated trend, and become closer as the propagation angle approaches , indicating reduced . At , the resonance response becomes significantly weakened or disappears because is suppressed to nearly zero for the thickness shear excitation in 128°Y-cut LN. The corresponding Bode responses in Figure 6 show the same angular dependence, decreasing as the propagation angle approaches 90°. The responses from 110° to 170° are not shown in Figure 5 and Figure 6 because the thickness shear excitation in 128°Y-cut LN is expected to be approximately symmetric with respect to 90°, as also observed in the FEA results in Figure 2. Therefore, the 10°–90° range is sufficient to show the monotonic reduction of and toward the symmetry point.
Figure 5. (a) Measured wideband admittance responses of the Design A resonators at different in-plane angles from 10° to 90°. Enlarged admittance responses of the (b) A, (d) A, and (f) A modes. Corresponding conductance responses of the (c) A, (e) A, and (g) A modes.
Figure 6. (a) Measured wideband Bode responses of the Design A resonators at different in-plane angles from 10° to 90°. Enlarged Bode responses of the (b) A, (c) A, (d) A, and (e) A modes.
To obtain more reliable values from the measured responses, a multi-branch modified mBVD model was used, as shown in Figure 7. Although the -based method in (1) provides a useful estimate of coupling, it can become unreliable for lossy or low- resonators, where the resonance and antiresonance peaks are broadened or shifted [28]. In addition, nearby spurious modes can distort the intended resonance response and lead to inaccurate coupling extraction [29].
Figure 7. mBVD fitting results and extracted model parameters for the Design A resonator at an in-plane angle of : (a) measured and fitted wideband admittance responses from 1 to 30 GHz; (b) measured and fitted wideband phase responses; enlarged admittance responses and mBVD fitting results of the (c) A, (d) A, and (e) A modes; (f) extracted mBVD model parameters; and (g) equivalent mBVD circuit model.
At high frequencies, routing inductance, routing resistance, pad capacitance, and other electromagnetic parasitics can further affect the measured admittance response. Therefore, the mBVD model was employed to separate the static capacitance, routing parasitics, and motional branches of the intended resonances, enabling more accurate extraction of from the measured data [30]. The representative mBVD fitting results in Figure 7 were obtained from the Design A resonator at an in-plane angle of 10°. Figure 7(a) and (Figure 7b) show that the measured wideband admittance and phase responses are well captured by the fitted model from 1 to 30 GHz. The enlarged fitting results in Figure 7(c)–(Figure 7e) further confirm that the A, A, and A resonances are accurately modeled. The extracted model parameters are summarized in Figure 7(f), and the corresponding equivalent mBVD circuit is shown in Figure 7(g). The values reported in the following statistical analysis are therefore extracted from the mBVD-fitted parameters.
Figure 8 summarizes the averaged Bode , , and mBVD-fitted values extracted from the four resonator designs as functions of in-plane angle for the A, A, and A modes. The corresponding individual-design results are provided in Supplementary Figs. S1–S4. The individual-design data confirm that the overall concave-up angular dependence of is observed in each design, following the same general trend as . The relatively large error bars, particularly for the A and A modes, mainly reflect design-to-design differences in the absolute values, as discussed in Supplementary Section S1. For each angle, the symbols represent the average values extracted from four resonator designs, and the error bars indicate the standard deviation (). The values were extracted only when a clear 3 dB bandwidth around the parallel resonant frequency could be identified; otherwise, the
data points were left blank. The detailed averaged values for the A, A, and A modes are summarized in Table I (PDF p. 7)–Table III, and the corresponding individual-design values are provided in Supplementary Tables S1–S3. The averaged Bode values for the A/A/A modes are 735/546, 204/149, and 59/37, respectively. At 90°, the averaged Bode values decrease to 66/9/12, while cannot be extracted. The averaged values follow the same trend, decreasing from 4.8%/2.0%/0.9% for the A/A/A modes to nearly zero at 90°. Overall, Figure 8 reveals a consistent concave-up angular dependence in both and across all three modes, indicating a strong correlation between anisotropic and anisotropic in 128°Y-cut LN resonators. Although the resonance response becomes increasingly weak near 90° as approaches zero, making quantitative extraction less reliable, the overall agreement in the angular trends of and remains evident.
| Angle (°) | (%) | Bode | |
| 10 | 4.8 | 676 | 546 |
| 30 | 3.6 | 241 | 123 |
| 50 | 2.4 | 208 | 159 |
| 70 | 0.9 | 111 | 51 |
| 90 | 0.0 | 66 | – |
| 110 | 1.0 | 183 | 140 |
| 130 | 2.6 | 278 | 259 |
| 150 | 4.0 | 545 | 429 |
| 170 | 4.8 | 735 | 509 |
Table I (PDF p. 7). Averaged resonator performance for A mode.
| Angle (°) | (%) | Bode | |
| 10 | 0.9 | 59 | 36 |
| 30 | 0.7 | 39 | 26 |
| 50 | 0.5 | 27 | – |
| 70 | 0.2 | 17 | – |
| 90 | 0.0 | 12 | – |
| 110 | 0.2 | 25 | – |
| 130 | 0.5 | 36 | 25 |
| 150 | 0.8 | 38 | 33 |
| 170 | 0.9 | 51 | 37 |
Table III. Averaged resonator performance for A mode.
Discussion
The measured results show that the anisotropic of the A, A, and A modes follows a trend similar to , with degraded near 90°. To examine whether this behavior can be explained by propagation-related loss, we considered the power flow angle (PFA) of the A mode in 128°Y-cut LN. In anisotropic piezoelectric materials, a nonzero PFA can cause the acoustic energy flow to deviate from the intended propagation direction, which may introduce additional propagation loss in resonator devices [33, 34, 35, 36].
| Angle (°) | (%) | Bode | |
| 10 | 1.9 | 204 | 149 |
| 30 | 1.5 | 122 | 90 |
| 50 | 0.9 | 38 | 12 |
| 70 | 0.4 | 20 | – |
| 90 | 0.0 | 9 | – |
| 110 | 0.4 | 8 | 6 |
| 130 | 1.0 | 66 | 32 |
| 150 | 1.7 | 109 | 95 |
| 170 | 2.0 | 165 | 147 |
Table II. Averaged resonator performance for A mode.
Figure 9(a) shows the calculated PFA of the A mode as a function of in-plane angle. The electrically short condition shows a relatively small PFA over the full angular range, while the electrically open condition exhibits larger PFA values. The PFA becomes zero at 0°, 90°, and 180°, and its absolute value reaches larger values around 50° and 130°. Figure 9(b) shows the simulated electromechanical coupling coefficient which reaches its maximum near 0° and 180° and decreases
Figure 9. Simulated propagation characteristics of the A mode in 128°Y-cut LN: (a) power flow angle and (b) electromechanical coupling coefficient as a function of in-plane angle.
toward 90°, consistent with the admittance simulation and measurement trends discussed earlier.
However, the measured trend cannot be explained by PFA alone. If PFA were the dominant loss mechanism, the largest loss would be expected near the angles where the absolute PFA is maximized, such as around 50° and 130°. In contrast, the measured Bode and are lowest near 90°, where the PFA is close to zero. This discrepancy indicates that, although PFA can contribute to propagation-related loss, it is unlikely to be the dominant cause of the anisotropic degradation observed in the 128°Y-cut LN resonators. Therefore, another orientation-dependent deformation mechanism must be considered.
To further investigate this mechanism, we performed full-device FEA using a one-pair-IDT resonator geometry, as shown in Figure 10. The displacement profiles in Figure 10 were evaluated at the parallel resonance frequency () of the A mode for each corresponding in-plane angle, namely 10.86, 10.82, 10.7, and 10.58 GHz for 10°, 30°, 50°, and 70°, respectively. This -based evaluation accounts for the orientation-dependent frequency shift and is consistent with the extraction of . This model was used to examine how the displacement field evolves near the anchor region as the in-plane propagation angle changes. As shown in Figure 10(b), the displacement component transverse to the intended acoustic propagation direction becomes increasingly pronounced near the anchors as the propagation angle approaches 90°, suggesting that the mode develops stronger unintended in-plane transverse motion. In 128°Y-cut LN, the effective thickness shear excitation becomes weaker as the propagation angle approaches 90°, as indicated by the reduction in . Under this condition, a larger portion of the vibration is coupled into an unintended transverse displacement component, which can more easily leak energy through the anchor regions. As a result, the measured decreases together with , even though the PFA does not predict maximum loss at . Therefore, the anisotropic behavior in these 128°Y-cut LN resonators is more strongly associated with orientation-dependent mode deformation and anchor-region energy leakage than with PFA alone.
Within the loss framework of (2), the measured trends can be separated into a mode-dependent baseline and an orientation-dependent excess loss. The reduction in the overall level from the A to the A mode is consistent with intrinsic damping mechanisms that become more pronounced at higher frequencies, including phonon-interaction-related loss [15, 37]. These intrinsic mechanisms can set the baseline for each mode and are not expected to vary strongly with the in-plane propagation angle. By contrast, the angular variation of within a given mode is more directly related to the . At high-coupling orientations, the intended thickness-shear motion is dominant and the unintended transverse displacement near the anchors remains weak, so the measured is closer to its intrinsic baseline. As the propagation direction is rotated toward , the weakened thickness-shear excitation is accompanied by stronger transverse displacement near the support regions, increasing anchor-mediated energy leakage and reducing . Therefore, the present results should not be interpreted as identifying the dominant loss mechanism at the highest- orientation. Rather, they show that the orientation-dependent degradation of away from the high-coupling directions is primarily associated with anchor-region energy leakage.
Conclusion
This work experimentally investigates the anisotropic of XBARs in 500-nm-thick 128°Y-cut LN resonators on Si. By characterizing A, A, and A modes from to with respect to the material -axis, clear orientation-dependent trends in both and were observed. The averaged Bode values were 735/546, 204/149, and 59/37 for the A, A, and A modes, respectively, while the average Bode values at decreased to 66/9/12. The extracted values showed the same angular dependence, decreasing from averaged values of 4.8%, 2.0%, and 0.9% for the A, A, and A modes to 0% at . FEA results further reveal that the degraded near cannot be fully explained by power flow angle alone. Instead, as the propagation angle approaches , the reduced thickness-shear excitation is accompanied by stronger unintended transverse displacement near the anchors, thereby enhancing acoustic energy leakage and lowering . These results indicate that the orientation-dependent degradation of in 128°Y-cut LN resonators, rather than the absolute level, is strongly linked to orientation-dependent mode deformation and anchor-region energy leakage. This study provides experimental evidence and physical insight into anisotropic loss mechanisms in 128°Y-cut LN XBARs, offering design guidance for jointly optimizing , , and propagation orientation in high-frequency acoustic devices.
Acknowledgment
This work was completed at the Texas Nanofabrication Facility Microelectronics Research Center.
References
References
- [1]C. C. W. Ruppel, “Acoustic Wave Filter Technology—A Review,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 64, no. 9, pp. 1390–1400, Sep. 2017.DOI
- [2]R. Abdolvand, H. M. Lavasani, G. K. Ho, and F. Ayazi, “Thin-film piezoelectric-on-silicon resonators for high-frequency reference oscillator applications,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 55, no. 12, pp. 2596–2606, Dec. 2008.
- [3]V. Yantchev and I. Katardjiev, “Thin film Lamb wave resonators in frequency control and sensing applications: A review,” Journal of Micromechanics and Microengineering, vol. 23, no. 4, p. 043001, Mar. 2013.DOI
- [4]E. A. Wollack, A. Y. Cleland, R. G. Gruenke, Z. Wang, P. Arrangoiz-Arriola, and A. H. Safavi-Naeini, “Quantum state preparation and tomography of entangled mechanical resonators,” Nature, vol. 604, no. 7906, pp. 463–467, Apr. 2022.DOI
- [5]R. Ruby, “A Snapshot in Time: The Future in Filters for Cell Phones,” IEEE Microwave Magazine, vol. 16, no. 7, pp. 46–59, Aug. 2015.DOI
- [6]S. Gong, R. Lu, Y. Yang, L. Gao, and A. E. Hassanien, “Microwave Acoustic Devices: Recent Advances and Outlook,” IEEE Journal of Microwaves, vol. 1, no. 2, pp. 601–609, Apr. 2021.DOI
- [7]R. Lu, “Recent advances in high-performance millimeter-wave acoustic resonators and filters using thin-film lithium niobate,” Progress in Quantum Electronics, vol. 100–101, p. 100565, Mar. 2025.DOI
- [8]R. Lu and S. Gong, “RF acoustic microsystems based on suspended lithium niobate thin films: Advances and outlook,” Journal of Micromechanics and Microengineering, vol. 31, no. 11, p. 114001, Sep. 2021.DOI
- [9]G. Pillai and S.-S. Li, “Piezoelectric MEMS Resonators: A Review,” IEEE Sensors Journal, vol. 21, no. 11, pp. 12589–12605, Jun. 2021.DOI
- [10]M. Li, K. Yang, J. Fang, F. Lin, and C. Zuo, “A1-Mode Lamb Wave Resonator in 128° Y-Cut Lithium Niobate with Electromechanical Coupling Coefficient of 57%,” in 2024 IEEE Ultrasonics, Ferroelectrics, and Frequency Control Joint Symposium (UFFC-JS), Sep. 2024, pp. 1–4.DOI
- [11]J. Kramer, B. T. Bosworth, L. Matto, N. R. Jungwirth, O. Barrera, F. Bergmann, S. Cho, V. Chulukhadze, M. Goorsky, N. D. Orloff, and R. Lu, “Acoustic resonators above 100 GHz,” Applied Physics Letters, vol. 127, no. 1, p. 012204, Jul. 2025.DOI
- [12]O. Barrera, J. Kramer, L. Matto, V. Chulukhadze, S. Cho, M. E. Liao, M. S. Goorsky, and R. Lu, “50 GHz Piezoelectric Acoustic Filter,” IEEE Journal of Microwaves, vol. 6, no. 2, pp. 391–400, Mar. 2026.DOI
- [13]Y. Yang, R. Lu, L. Gao, and S. Gong, “10–60-GHz Electromechanical Resonators Using Thin-Film Lithium Niobate,” IEEE Transactions on Microwave Theory and Techniques, vol. 68, no. 12, pp. 5211–5220, Dec. 2020.DOI
- [14]J. Kramer, J. Campbell, T.-H. Hsu, I. Anderson, and R. Lu, “Cryogenic Q enhancement in 50 GHz piezoelectric resonators,” Applied Physics Letters, vol. 128, no. 10, p. 102205, Mar. 2026.
- [15]R. Tabrizian, M. Rais-Zadeh, and F. Ayazi, “Effect of phonon interactions on limiting the f.Q product of micromechanical resonators,” in TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference, Jun. 2009, pp. 2131–2134.
- [16]A. Hagelauer, R. Ruby, S. Inoue, V. Plessky, K.-Y. Hashimoto, R. Nakagawa, J. Verdu, P. de Paco, A. Mortazawi, G. Piazza, Z. Schaffer, E. T.-T. Yen, T. Forster, and A. Tag, “From Microwave Acoustic Filters to Millimeter-Wave Operation and New Applications,” IEEE Journal of Microwaves, vol. 3, no. 1, pp. 484–508, Jan. 2023.DOI
- [17]T. Anunsor, O. Barrera, J. Kramer, I. Anderson, Z. Yao, V. Chulukhadze, and R. Lu, “Practical Demonstrations of F3-Band Thin-Film Lithium Niobate Acoustic Filter Design,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 72, no. 12, pp. 1650–1662, Dec. 2025.
- [18]S. Gong and G. Piazza, “Design and Analysis of Lithium–Niobate-Based High Electromechanical Coupling RF-MEMS Resonators for Wideband Filtering,” IEEE Transactions on Microwave Theory and Techniques, vol. 61, no. 1, pp. 403–414, Jan. 2013.DOI
- [19]F. V. Pop, A. S. Kopchar, G. Vidal-Álvarez, and G. Piazza, “Investigation of Electromechanical Coupling and Quality Factor of X-Cut Lithium Niobate Laterally Vibrating Resonators Operating Around 400 MHz,” Journal of Microelectromechanical Systems, vol. 27, no. 3, pp. 407–413, Jun. 2018.DOI
- [20]S.-M. Wu, H. Yan, C.-B. Hao, Z.-H. Qin, S.-Y. Yu, and Y.-F. Chen, “K-Band LiNbO3 A3 Lamb-Wave Resonators With Through-Holes,” Journal of Microelectromechanical Systems, vol. 34, no. 2, pp. 164–173, Apr. 2025.DOI
- [21]M. Faizan and L. G. Villanueva, “Optimization of Inactive Regions of Lithium Niobate Shear Mode Resonator for Quality Factor Enhancement,” Journal of Microelectromechanical Systems, vol. 30, no. 3, pp. 369–374, Jun. 2021.DOI
- [22]J. Kramer and R. Lu, “A Generalized Acoustic Framework for Multilayer Piezoelectric Platforms,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 72, no. 9, pp. 1302–1311, Sep. 2025.DOI
- [23]Y. Liu, X. Xu, J. Li, and T. Wu, “High Figure-of-Merit 36Y-Cut LiNbO3 Lamb Wave Resonators With Dissipation Loss Optimization,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 72, no. 8, pp. 1021–1028, Aug. 2025.DOI
- [24]R. Lu, T. Manzaneque, Y. Yang, and S. Gong, “Exploiting parallelism in resonators for large voltage gain in low power wake up radio front ends,” in 2018 IEEE Micro Electro Mechanical Systems (MEMS), Jan. 2018, pp. 747–750.DOI
- [25]Y.-H. Song and S. Gong, “Arraying SH0 Lithium Niobate laterally vibrating resonators for mitigation of higher order spurious modes,” in 2016 IEEE 29th International Conference on Micro Electro Mechanical Systems (MEMS), Jan. 2016, pp. 111–114.DOI
- [26]Y. Yang, R. Lu, and S. Gong, “High Q Antisymmetric Mode Lithium Niobate MEMS Resonators With Spurious Mitigation,” Journal of Microelectromechanical Systems, vol. 29, no. 2, pp. 135–143, Apr. 2020.DOI
- [27]Y. Yang, L. Gao, R. Lu, and S. Gong, “Lateral Spurious Mode Suppression in Lithium Niobate A1 Resonators,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 68, no. 5, pp. 1930–1937, May 2021.DOI
- [28]R. Naik, J. Lutsky, R. Reif, and C. Sodini, “Electromechanical coupling constant extraction of thin-film piezoelectric materials using a bulk acoustic wave resonator,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 45, no. 1, pp. 257–263, Jan. 1998.DOI
- [29]R. Lu, M.-H. Li, Y. Yang, T. Manzaneque, and S. Gong, “Accurate Extraction of Large Electromechanical Coupling in Piezoelectric MEMS Resonators,” Journal of Microelectromechanical Systems, vol. 28, no. 2, pp. 209–218, Apr. 2019.DOI
- [30]J. Larson, P. Bradley, S. Wartenberg, and R. Ruby, “Modified Butterworth-Van Dyke circuit for FBAR resonators and automated measurement system,” in 2000 IEEE Ultrasonics Symposium. Proceedings. An International Symposium (Cat. No.00CH37121), vol. 1, Oct. 2000, pp. 863–868 vol.1.DOI
- [31]C. Tu, J. E.-Y. Lee, and X.-S. Zhang, “Dissipation Analysis Methods and Q-Enhancement Strategies in Piezoelectric MEMS Laterally Vibrating Resonators: A Review,” Sensors, vol. 20, no. 17, p. 4978, Jan. 2020.DOI
- [32]R. Jin, Z. Cao, M. Patel, B. Abbott, D. Molinero, and D. Feld, “An improved formula for estimating stored energy in a BAW resonator by its measured S11 parameters,” in 2021 IEEE International Ultrasonics Symposium (IUS). IEEE, 2021, pp. 1–5.DOI
- [33]R. Lu, T. Manzaneque, Y. Yang, M.-H. Li, and S. Gong, “Gigahertz Low-Loss and Wideband SO Mode Lithium Niobate Acoustic Delay Lines,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 66, no. 8, pp. 1373–1386, Aug. 2019.
- [34]I. E. Kuznetsova, B. D. Zaitsev, A. A. Teplykh, S. G. Joshi, and A. S. Kuznetsova, “The power flow angle of acoustic waves in thin piezoelectric plates,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 55, no. 9, pp. 1984–1991, Sep. 2008.
- [35]R. Lu and S. Gong, “Power Flow Angles of GHz Propagating Acoustic Waves in Thin-Film Lithium Niobate,” in 2021 IEEE International Ultrasonics Symposium (IUS), Sep. 2021, pp. 1–4.DOI
- [36]D. Lee, S. Meyer, S. Gong, R. Lu, and K. Lai, “Visualization of acoustic power flow in suspended thin-film lithium niobate phononic devices,” Applied Physics Letters, vol. 119, no. 21, p. 214101, Nov. 2021.DOI
- [37]S. A. Chandorkar, M. Agarwal, R. Melamud, R. N. Candler, K. E. Goodson, and T. W. Kenny, “Limits of quality factor in bulk-mode micromechanical resonators,” in 2008 IEEE 21st International Conference on Micro Electro Mechanical Systems, Jan. 2008, pp. 74–77.DOI