betaFeedback

WorksPhysics and Astronomy

In-Plane Q Anisotropy of Higher-Order XBARs in 128°Y-Cut Lithium Niobate

Abstract

128∘^\circY-cut lithium niobate (LN) laterally field-excited higher-order antisymmetric bulk acoustic resonators (XBARs) have attracted interest for high-frequency acoustic devices thanks to their high electromechanical coupling coefficient (k2k^2), high quality factor (QQ) from low metal coverage ratio, and thickness-defined resonant frequency. So far, the in-plane orientation of these resonators is commonly chosen to maximize k2k^2, thereby maximizing bandwidth. More recently, in-plane-rotated XBARs in 128∘^\circY-cut LN have been built to provide greater design flexibility in filter synthesis. However, the in-plane anisotropy of QQ has been far less explored. This leaves an important gap in understanding whether the propagation direction that determines k2k^2 also affects QQ. In this work, we investigate the anisotropic QQ of higher-order antisymmetric modes (namely, A3_3, A5_5, and A7_7) in 500-nm-thick 128∘^\circY-cut LN on Si. By characterizing resonator performance in various in-plane orientations, we observe that both Bode QQ and Q3dB,fpQ_{\mathrm{3dB}, f_p} show minimum values at 90∘^\circ to the material x-axis and maximum values around 0∘^\circ, following a trend similar to k2k^2. The A3_3, A5_5, and A7_7 modes around 10.4, 17, and 24 GHz exhibit averaged Bode QQ/Q3dB,fpQ_{\mathrm{3dB}, f_p} values of 735/556, 204/149, and 59/37, respectively. At 90∘^\circ, the average Bode QQ values are reduced to 66, 9, and 12. Finite element analysis (FEA) results suggest that the orientation-dependent degradation of QQ near 90∘^\circ is associated with stronger transverse displacement near the inactive and anchor regions, resulting in enhanced energy leakage. These results reveal an orientation-dependent loss pathway in 128∘^\circY-cut LN XBARs and provide design guidance for jointly optimizing k2k^2 and QQ.

Image not extracted

Figure 1.

Introduction

Acoustic resonators are essential components in modern electronic systems, including radio-frequency (RF) front-end filters [1], oscillators [2], sensors [3], and emerging quantum acoustic platforms [4]. Their compact footprint, frequency scalability, and efficient electromechanical transduction make them attractive for highly integrated signal-processing systems [5], [6]. Among various piezoelectric materials, lithium niobate (LN) has emerged as a promising platform for high-performance acoustic resonators due to its strong piezoelectricity and large electromechanical coupling coefficient (k2k^2) [7, 8, 9]. In particular, 128°Y-cut LN has been widely used for laterally excited bulk acoustic resonators (XBARs), where strong coupling has enabled high-frequency acoustic devices [10, 11, 12].

As wireless communication systems continue to evolve toward higher frequencies and wider bandwidths, both k2k^2 and quality factor (QQ) become critical performance metrics [13, 14, 15, 16]. While k2k^2 determines the energy transduction efficiency and achievable bandwidth, QQ governs acoustic energy dissipation and directly affects insertion loss, frequency selectivity, and overall resonator efficiency [8], [17]. Therefore, understanding how both k2k^2 and QQ vary with device design and material orientation is essential for optimizing LN acoustic resonators [18, 19, 20, 21].

Because LN is strongly anisotropic, the in-plane propagation orientation has been widely used as a key design parameter for improving resonator performance. In 128°Y-cut LN, previous studies have primarily utilized this anisotropy to identify orientations that maximize k2k^2, particularly for high-coupling XBARs [10], [22]. However, optimizing k2k^2 alone does not necessarily guarantee high QQ.

Recent studies have begun to show that acoustic dissipation in LN resonators can also depend strongly on propagation orientation. For example, anisotropic QQ behavior has been reported in X-cut LN S0_0 resonators [19] and in 36°Y-cut

This work was supported by the National Science Foundation (NSF) under CAREER Award No. 2339731, and a graduate fellowship from the Ministry of National Defense of the Republic of Korea.

Byeongjin Kim, Ian Anderson, and Ruochen Lu are with the Electrical and Computer Engineering Department, The University of Texas at Austin (email: [email protected]). Highlights

  • Anisotropic QQ of higher-order antisymmetric modes (A3A_3/A5A_5/A7A_7) measured in 128°Y-cut LN on Si

  • Averaged Bode QQ of 735/204/59 (A3A_3/A5A_5/A7A_7) follows k2k^2, dropping sharply to 66/9/12 at 90°

  • FEA suggests that reduced QQ near 90° is consistent with enhanced transverse motion near the anchors

Index Terms— 128°Y-cut lithium niobate, anchor loss, anisotropy, higher-order antisymmetric mode, laterally excited bulk acoustic resonator (XBAR), quality factor

LN SH0_0 resonators [23]. In these platforms, the resonance quality factor was shown to vary with in-plane propagation angle, indicating that acoustic loss is also governed by crystal anisotropy. These studies suggest that maximizing k2k^2 alone is insufficient for realizing optimal resonator performance and that orientation-dependent loss mechanisms must also be considered. Nevertheless, a systematic investigation of anisotropic QQ in 128°Y-cut LN XBARs remains limited, despite the importance of this cut for high-frequency, high-coupling acoustic devices.

In this work, we experimentally investigate the anisotropic QQ of higher-order antisymmetric modes in 500-nm-thick 128°Y-cut LN on Si. By characterizing A3A_3, A5A_5, and A7A_7 modes as a function of in-plane propagation orientation, we observe that both Bode QQ and 3dBQQ at the parallel resonant frequency (Q3dB,fpQ_{3\mathrm{dB},fp}) follow a trend similar to k2k^2, with minimum values at 90° and maximum values at 0° and 180°. The A3A_3, A5A_5, and A7A_7 modes around 10.4, 17, and 24 GHz exhibit averaged Bode QQ/Q3dB,fpQ_{3\mathrm{dB},fp} values of 735/546, 204/149, and 59/37, respectively. At 90°, the average Bode QQ values are reduced to 66, 9, and 12 for the A3A_3, A5A_5, and A7A_7 modes, while Q3dB,fpQ_{3\mathrm{dB},fp} cannot be reliably extracted because of the weak resonance response. FEA results further indicate that unintended transverse displacement is strongest at 90°, particularly near the anchors, leading to increased acoustic energy leakage and reduced QQ. These results suggest that the orientation-dependent degradation of QQ in 128°Y-cut LN XBARs is strongly influenced by transverse mode deformation and anchor-region leakage, providing design guidelines for simultaneously optimizing k2k^2 and QQ.

Design and Simulation

To investigate the orientation-dependent behavior of 128°Y-cut LN resonators, the device geometry was designed as shown in Fig. 1(a). The resonator consists of interdigitated transducers (IDTs) patterned on a suspended 500-nm-thick LN resonant body with release windows defined around the active region. A series of MEMS resonators are arranged with respect to the material xx-axis, and the in-plane angle is defined as the counterclockwise rotation angle from the xx-axis. The key design parameters, including resonator length (LrL_r), resonator width (WrW_r), electrode width (WeW_e), gap width (WgW_g), window width (WwW_w), and device number (NtN_t), are summarized in the table in Fig. 1(a). The resonator array was designed to suppress spurious modes and obtain cleaner resonance responses from the intended antisymmetric modes, enabling a more reliable evaluation of anisotropic QQ [24, 25].

Image not extracted

Figure 1 (PDF p. 2). (a) Schematic of the spurious-mode-suppressed 128°Y-cut LN resonator design with key dimensions summarized in the table. (b) Simulated wideband admittance response of the resonator array with representative displacement mode shapes.

Sym.ParameterValue
LrL_rResonator length72–152 μm
WrW_rResonator width10 μm
WeW_eElectrode width2–3 μm
WgW_gGap width1–2 μm
WwW_wWindow width8 μm
NtN_tDevice number10

Table 1.

Fig. 1(b) shows the simulated wideband admittance response of the resonator array together with representative displacement mode shapes. Clear resonances are observed for the A3A_3, A5A_5, and A7A_7 modes at approximately 10.6, 17.4, and 24.4 GHz, respectively, each showing a well-defined thickness-shear displacement profile. In contrast, the A1A_1 mode exhibits multiple spurious responses around the main resonance. This is likely because the duty cycle, defined as the ratio of the electrode width to the IDT period, and the LN thickness are not optimized to match the dispersion between the metalized and non-metalized regions of the A1A_1 mode in the present stack. The resulting velocity mismatch can perturb the lateral mode profile and introduce multiple higher-order spurious responses around the main resonance [26, 27]. Therefore, the A1A_1 mode is excluded from the anisotropic QQ analysis, and the following study focuses on the A3A_3, A5A_5, and A7A_7 higher-order antisymmetric modes, which provide clearer modal responses.

The effective kt2k_t^2 in spurious-free resonators with high QQ can be approximated by:

kt2=π28[(fpfs)2−1](1)k_t^2 = \frac{\pi^2}{8}\left[\left(\frac{f_p}{f_s}\right)^2-1\right] \tag*{(1)}

where fsf_s and fpf_p are the simulated series and parallel resonant frequencies. This fs/fpf_s/f_p-based kt2k_t^2 is equivalent to the kt2k_t^2 value later extracted from the modified Butterworth–Van Dyke (mBVD) model. However, because routing resistance, parasitic capacitance, and other high-frequency parasitics can distort the apparent fsf_s and fpf_p spacing, the measured kt2k_t^2 values are extracted using mBVD fitting [28, 29, 30].

For the higher-order antisymmetric modes in 128°Y-cut LN, the excitation is mainly associated with the piezoelectric stress coefficient e15e_{15}, which varies strongly with in-plane propagation angle [10, 22]. This angular dependence leads to the kt2k_t^2 trend shown later in Figure 8, where kt2k_t^2 reaches its minimum at 90° and maximum values at 0° and 180°. Consistent with this trend, the simulated admittance responses in Figure 2 show that, for the A3_3, A5_5, and A7_7 modes, fsf_s and fpf_p become closer as the propagation angle approaches 90°, indicating reduced kt2k_t^2.

Image not extracted

Figure 2. Simulated admittance responses of the 128°Y-cut LN resonators at different in-plane angles from 10° to 170°: (a) A3_3 mode; (b) A5_5 mode; (c) A7_7 mode. The reduction in kt2k_t^2 toward 90° is observed for all three modes.

Image not extracted

Figure 8. Extracted Bode QQ, Q3dB,fpQ_{3\mathrm{dB},fp}, and mBVD-fitted k2k^2 as functions of in-plane angle for the (a) A3_3, (b) A5_5, and (c) A7_7 modes.

Although the simulations capture the anisotropic coupling trend, the experimentally measured QQ is difficult to predict in advance because it depends on multiple loss contributions. The total quality factor is determined by the ratio of stored to dissipated energy and can be expressed as

Qtotal=2πEstoredEdissipated=(Qanchor−1+QTED−1+Qother−1)−1.(2)\begin{aligned} Q_{\mathrm{total}} = 2\pi\frac{E_{\mathrm{stored}}}{E_{\mathrm{dissipated}}} \\ &= \left(Q_{\mathrm{anchor}}^{-1}+Q_{\mathrm{TED}}^{-1}+Q_{\mathrm{other}}^{-1}\right)^{-1}. \tag*{(2)} \end{aligned}

where EstoredE_{\mathrm{stored}} and EdissipatedE_{\mathrm{dissipated}} are the stored and dissipated energy per cycle, respectively, and QanchorQ_{\mathrm{anchor}}, QTEDQ_{\mathrm{TED}}, and QotherQ_{\mathrm{other}} correspond to anchor loss, thermoelastic damping (TED), and other loss mechanisms, respectively [31]. Since these loss contributions depend on material properties, electrode conditions, fabrication variations, and resonator geometry, predefined material quality factors were assigned to LN and the electrodes as practical damping parameters, with QLN=400Q_{\mathrm{LN}=400} and Qelectrode=20Q_{\mathrm{electrode}}=20, to obtain finite simulated admittance responses. These values are used only to compare relative resonance behavior and mode shapes, while the actual anisotropic QQ must be determined experimentally.

Using this finite element analysis (FEA) framework, the simulated mode-shape results in Figure 3 further clarify the orientation-dependent deformation of the A3_3 mode. Figure 3(a) shows the unit-cell displacement and TxzT_{xz} stress distribution, confirming that the intended mode is dominated by thickness-shear deformation. The enlarged top-view displacement profiles in Figure 3(b) reveal a clear orientation-dependent deformation behavior. As the in-plane propagation angle increases from 10° to 70° and approaches 90°, the unintended transverse displacement component, corresponding to the yy-direction, becomes increasingly pronounced. The 90° case is not included in Figure 3(b) because a well-defined A3_3 resonance could not be identified at this orientation. Figure 3(a) and Figure 3(b) were obtained from a periodic active-region model, which does not include the inactive or anchor regions. Therefore, these profiles are used to identify orientation-dependent transverse deformation, not to directly calculate anchor loss or absolute QQ. To provide a more quantitative FEM comparison, additional finite one-pair-IDT resonator simulations were performed for the A3, A5, and A7 modes at in-plane angles from 10∘10^\circ to 170∘170^\circ in 20∘20^\circ increments. The simulated Q3dB,fpQ_{3\mathrm{dB},f_p} was extracted from the admittance response and is shown in Figure 3(c), while the corresponding one-pair-IDT resonator model and anchor-region displacement fields are further examined in Figure 10. Data points for which the resonance was too weak to reliably extract the Q3dB,fpQ_{3\mathrm{dB},f_p} were omitted. The reduced QQ at orientations with larger transverse deformation indicates that this deformation can couple to the inactive and anchor regions in the finite resonator, leading to enhanced acoustic energy leakage.

Image not extracted

Figure 3. Simulated A3_3 mode shape and orientation-dependent deformation of the 128°Y-cut LN resonator: (a) unit-cell displacement and TxzT_{xz} stress distributions; (b) enlarged top view displacement profiles with deformation at in-plane angles of 10°, 30°, 50°, and 70°; (c) simulated Q3dB,fpQ_{3\mathrm{dB},f_p} of the A3_3, A5_5, and A7_7 modes obtained from a finite one-pair-IDT resonator model at different in-plane angles.

Image not extracted

Figure 10. Simulated displacement distributions of the A3_3 mode evaluated at the parallel resonance frequency (fpf_p): (a) overall displacement profile of a one-pair-IDT resonator; (b) enlarged views of the anchor region at in-plane angles of 10°, 30°, 50°, and 70°, showing enhanced displacement leakage toward the anchor as the in-plane angle approaches 90°.

These simulation results motivate the experimental investigation of resonators with different in-plane propagation orientations. While Figure 2 shows that kt2k_t^2 decreases toward 90∘90^\circ, Figure 3 suggests that the unintended transverse displacement becomes stronger and the simulated Q3dB,fpQ_{3\mathrm{dB},f_p} decreases in the same angular range. Therefore, measuring the actual resonator responses across different orientations is necessary to determine whether the anisotropic QQ trend is accompanied by the anisotropic coupling trend and to clarify the dominant loss behavior in 128°Y-cut LN XBARs.

Fabrication and Measurement

XBAR resonator arrays were fabricated from 500-nm-thick 128°Y-cut LN on Si substrates provided by NGK Corporation. Figure 4(a) shows the fabrication flow of the suspended resonators. First, fine IDT electrodes were defined by photolithography using an MA8 mask aligner, followed by 50 nm Pt deposition using e-beam evaporation and lift-off in PG remover with sonication. A second photolithography step was then performed to define the buslines and probing pads, followed by 80 nm Au deposition and lift-off. After metal patterning, release windows were defined by photolithography and etched through the LN layer using ion milling. Finally, the underlying Si was removed using XeF2_2 isotropic etching to form suspended 128°Y-cut LN resonators. Figure 4(b) shows optical micrographs of the fabricated resonators. Four resonator designs, labeled A–D, were fabricated by varying the resonator length and electrode width. For each design, devices were arranged at different in-plane propagation angles from 10∘10^\circ to 170∘170^\circ in 20∘20^\circ increments, measured with respect to the material xx-axis. This design set enables statistical comparison of resonators with different dimensions at each propagation orientation, allowing the anisotropic QQ trend to be evaluated more reliably.

Image not extracted

Figure 4. (a) Fabrication flow of the suspended 128°Y-cut LN resonators. (b) Optical micrographs of fabricated resonators with different resonator lengths and electrode widths.

The measured admittance and Bode QQ responses shown in Figure 5 and Figure 6 were obtained from Design A, whose complete structural parameters are summarized in Figure 4. Therefore, the resonators compared across different in-plane angles in these figures have identical geometry, with Lr=72L_r = 72 µm and We=3W_e = 3 µm. The Bode QQ was extracted using the improved S11S_{11}-parameter-based method after converting the measured admittance response to S11S_{11} {[32]}. Figure 5(a) shows the measured wideband admittance responses of the fabricated resonators at different in-plane angles from 10∘10^\circ to 90∘90^\circ. The enlarged measured admittance responses of the A3_3, A5_5, and A7_7 modes around 10.4, 17, and 24 GHz are shown in Figure 5(b), (Figure 5d), and (Figure 5f), respectively, while the corresponding conductance responses are presented in Figure 5(c), (Figure 5e), and (Figure 5g). Compared with the admittance, the conductance provides a clearer visualization of the resonance linewidth, peak strength, and possible lossy or spurious responses, particularly at weak-coupling orientations. As the propagation angle approaches 90∘90^\circ, the conductance peaks become progressively weaker and broader before eventually becoming indistinguishable from the background response. The increased resonance linewidth observed in the conductance responses is consistent with the reduction in the measured Bode QQ shown in Figure 6. Small differences between the measured resonance frequencies and the simulated values, as well as device-to-device frequency variations, are mainly attributed to thickness nonuniformity within the same LN-on-Si sample. As expected from the simulated kt2k_t^2 trend, fsf_s and fpf_p become closer as the propagation angle approaches 90∘90^\circ, indicating reduced kt2k_t^2. At 90∘90^\circ, the resonance response becomes significantly weakened or disappears because kt2k_t^2 is suppressed to nearly zero for the thickness shear excitation in 128°Y-cut LN. The corresponding Bode QQ responses in Figure 6 show the same angular dependence, decreasing as the propagation angle approaches 90°. The responses from 110° to 170° are not shown in Figure 5 and Figure 6 because the thickness shear excitation in 128°Y-cut LN is expected to be approximately symmetric with respect to 90°, as also observed in the FEA results in Figure 2. Therefore, the 10°–90° range is sufficient to show the monotonic reduction of kt2k_t^2 and QQ toward the symmetry point.

Image not extracted

Figure 5. (a) Measured wideband admittance responses of the Design A resonators at different in-plane angles from 10° to 90°. Enlarged admittance responses of the (b) A3_3, (d) A5_5, and (f) A7_7 modes. Corresponding conductance responses of the (c) A3_3, (e) A5_5, and (g) A7_7 modes.

Image not extracted

Figure 6. (a) Measured wideband Bode QQ responses of the Design A resonators at different in-plane angles from 10° to 90°. Enlarged Bode QQ responses of the (b) A1_1, (c) A3_3, (d) A5_5, and (e) A7_7 modes.

To obtain more reliable kt2k_t^2 values from the measured responses, a multi-branch modified mBVD model was used, as shown in Figure 7. Although the fs/fpf_s/f_p-based method in (1) provides a useful estimate of coupling, it can become unreliable for lossy or low-QQ resonators, where the resonance and antiresonance peaks are broadened or shifted [28]. In addition, nearby spurious modes can distort the intended resonance response and lead to inaccurate coupling extraction [29].

Image not extracted

Figure 7. mBVD fitting results and extracted model parameters for the Design A resonator at an in-plane angle of 10∘10^\circ: (a) measured and fitted wideband admittance responses from 1 to 30 GHz; (b) measured and fitted wideband phase responses; enlarged admittance responses and mBVD fitting results of the (c) A3_3, (d) A5_5, and (e) A7_7 modes; (f) extracted mBVD model parameters; and (g) equivalent mBVD circuit model.

At high frequencies, routing inductance, routing resistance, pad capacitance, and other electromagnetic parasitics can further affect the measured admittance response. Therefore, the mBVD model was employed to separate the static capacitance, routing parasitics, and motional branches of the intended resonances, enabling more accurate extraction of kt2k_t^2 from the measured data [30]. The representative mBVD fitting results in Figure 7 were obtained from the Design A resonator at an in-plane angle of 10°. Figure 7(a) and (Figure 7b) show that the measured wideband admittance and phase responses are well captured by the fitted model from 1 to 30 GHz. The enlarged fitting results in Figure 7(c)–(Figure 7e) further confirm that the A3_3, A5_5, and A7_7 resonances are accurately modeled. The extracted model parameters are summarized in Figure 7(f), and the corresponding equivalent mBVD circuit is shown in Figure 7(g). The kt2k_t^2 values reported in the following statistical analysis are therefore extracted from the mBVD-fitted parameters.

Figure 8 summarizes the averaged Bode QQ, Q3dB,fpQ_{3\mathrm{dB},f_p}, and mBVD-fitted kt2k_t^2 values extracted from the four resonator designs as functions of in-plane angle for the A3_3, A5_5, and A7_7 modes. The corresponding individual-design results are provided in Supplementary Figs. S1–S4. The individual-design data confirm that the overall concave-up angular dependence of QQ is observed in each design, following the same general trend as kt2k_t^2. The relatively large error bars, particularly for the A5_5 and A7_7 modes, mainly reflect design-to-design differences in the absolute QQ values, as discussed in Supplementary Section S1. For each angle, the symbols represent the average values extracted from four resonator designs, and the error bars indicate the standard deviation (σ\sigma). The Q3dB,fpQ_{3\mathrm{dB},fp} values were extracted only when a clear 3 dB bandwidth around the parallel resonant frequency could be identified; otherwise, the

data points were left blank. The detailed averaged values for the A3_3, A5_5, and A7_7 modes are summarized in Table I (PDF p. 7)–Table III, and the corresponding individual-design values are provided in Supplementary Tables S1–S3. The averaged Bode Q/Q3dB,fpQ/Q_{3\mathrm{dB},fp} values for the A3_3/A5_5/A7_7 modes are 735/546, 204/149, and 59/37, respectively. At 90°, the averaged Bode QQ values decrease to 66/9/12, while Q3dB,fpQ_{3\mathrm{dB},fp} cannot be extracted. The averaged k2k^2 values follow the same trend, decreasing from 4.8%/2.0%/0.9% for the A3_3/A5_5/A7_7 modes to nearly zero at 90°. Overall, Figure 8 reveals a consistent concave-up angular dependence in both k2k^2 and QQ across all three modes, indicating a strong correlation between anisotropic QQ and anisotropic k2k^2 in 128°Y-cut LN resonators. Although the resonance response becomes increasingly weak near 90° as k2k^2 approaches zero, making quantitative QQ extraction less reliable, the overall agreement in the angular trends of k2k^2 and QQ remains evident.

Angle (°)kt2k_t^2 (%)Bode QQQ3dB,fpQ_{3\mathrm{dB},f_p}
104.8676546
303.6241123
502.4208159
700.911151
900.066–
1101.0183140
1302.6278259
1504.0545429
1704.8735509

Table I (PDF p. 7). Averaged resonator performance for A3_3 mode.

Angle (°)kt2k_t^2 (%)Bode QQQ3dB,fpQ_{3\mathrm{dB},f_p}
100.95936
300.73926
500.527–
700.217–
900.012–
1100.225–
1300.53625
1500.83833
1700.95137

Table III. Averaged resonator performance for A7_7 mode.

Discussion

The measured results show that the anisotropic QQ of the A3_3, A5_5, and A7_7 modes follows a trend similar to k2k^2, with degraded QQ near 90°. To examine whether this behavior can be explained by propagation-related loss, we considered the power flow angle (PFA) of the A3_3 mode in 128°Y-cut LN. In anisotropic piezoelectric materials, a nonzero PFA can cause the acoustic energy flow to deviate from the intended propagation direction, which may introduce additional propagation loss in resonator devices [33, 34, 35, 36].

Angle (°)kt2k_t^2 (%)Bode QQQ3dB,fpQ_{3\mathrm{dB},f_p}
101.9204149
301.512290
500.93812
700.420–
900.09–
1100.486
1301.06632
1501.710995
1702.0165147

Table II. Averaged resonator performance for A5_5 mode.

Figure 9(a) shows the calculated PFA of the A3_3 mode as a function of in-plane angle. The electrically short condition shows a relatively small PFA over the full angular range, while the electrically open condition exhibits larger PFA values. The PFA becomes zero at 0°, 90°, and 180°, and its absolute value reaches larger values around 50° and 130°. Figure 9(b) shows the simulated electromechanical coupling coefficient kt2k_t^2 which reaches its maximum near 0° and 180° and decreases

Image not extracted

Figure 9. Simulated propagation characteristics of the A3_3 mode in 128°Y-cut LN: (a) power flow angle and (b) electromechanical coupling coefficient kt2k_t^2 as a function of in-plane angle.

toward 90°, consistent with the admittance simulation and measurement trends discussed earlier.

However, the measured QQ trend cannot be explained by PFA alone. If PFA were the dominant loss mechanism, the largest loss would be expected near the angles where the absolute PFA is maximized, such as around 50° and 130°. In contrast, the measured Bode QQ and Q3dB,fpQ_{3\mathrm{dB},f_p} are lowest near 90°, where the PFA is close to zero. This discrepancy indicates that, although PFA can contribute to propagation-related loss, it is unlikely to be the dominant cause of the anisotropic QQ degradation observed in the 128°Y-cut LN resonators. Therefore, another orientation-dependent deformation mechanism must be considered.

To further investigate this mechanism, we performed full-device FEA using a one-pair-IDT resonator geometry, as shown in Figure 10. The displacement profiles in Figure 10 were evaluated at the parallel resonance frequency (fpf_p) of the A3_3 mode for each corresponding in-plane angle, namely 10.86, 10.82, 10.7, and 10.58 GHz for 10°, 30°, 50°, and 70°, respectively. This fpf_p-based evaluation accounts for the orientation-dependent frequency shift and is consistent with the extraction of Q3dB,fpQ_{3\mathrm{dB},f_p}. This model was used to examine how the displacement field evolves near the anchor region as the in-plane propagation angle changes. As shown in Figure 10(b), the displacement component transverse to the intended acoustic propagation direction becomes increasingly pronounced near the anchors as the propagation angle approaches 90°, suggesting that the mode develops stronger unintended in-plane transverse motion. In 128°Y-cut LN, the effective thickness shear excitation becomes weaker as the propagation angle approaches 90°, as indicated by the reduction in k2k^{2}. Under this condition, a larger portion of the vibration is coupled into an unintended transverse displacement component, which can more easily leak energy through the anchor regions. As a result, the measured QQ decreases together with k2k^{2}, even though the PFA does not predict maximum loss at 90∘90^{\circ}. Therefore, the anisotropic QQ behavior in these 128°Y-cut LN resonators is more strongly associated with orientation-dependent mode deformation and anchor-region energy leakage than with PFA alone.

Within the loss framework of (2), the measured QQ trends can be separated into a mode-dependent baseline and an orientation-dependent excess loss. The reduction in the overall QQ level from the A3_3 to the A7_7 mode is consistent with intrinsic damping mechanisms that become more pronounced at higher frequencies, including phonon-interaction-related loss [15, 37]. These intrinsic mechanisms can set the baseline QQ for each mode and are not expected to vary strongly with the in-plane propagation angle. By contrast, the angular variation of QQ within a given mode is more directly related to the QanchorQ_{\mathrm{anchor}}. At high-coupling orientations, the intended thickness-shear motion is dominant and the unintended transverse displacement near the anchors remains weak, so the measured QQ is closer to its intrinsic baseline. As the propagation direction is rotated toward 90∘90^{\circ}, the weakened thickness-shear excitation is accompanied by stronger transverse displacement near the support regions, increasing anchor-mediated energy leakage and reducing QanchorQ_{\mathrm{anchor}}. Therefore, the present results should not be interpreted as identifying the dominant loss mechanism at the highest-QQ orientation. Rather, they show that the orientation-dependent degradation of QQ away from the high-coupling directions is primarily associated with anchor-region energy leakage.

Conclusion

This work experimentally investigates the anisotropic QQ of XBARs in 500-nm-thick 128°Y-cut LN resonators on Si. By characterizing A3_3, A5_5, and A7_7 modes from 10∘10^{\circ} to 170∘170^{\circ} with respect to the material xx-axis, clear orientation-dependent trends in both k2k^{2} and QQ were observed. The averaged Bode Q/Q3dB,fpQ/Q_{\mathrm{3dB},fp} values were 735/546, 204/149, and 59/37 for the A3_3, A5_5, and A7_7 modes, respectively, while the average Bode QQ values at 90∘90^{\circ} decreased to 66/9/12. The extracted k2k^{2} values showed the same angular dependence, decreasing from averaged values of 4.8%, 2.0%, and 0.9% for the A3_3, A5_5, and A7_7 modes to 0% at 90∘90^{\circ}. FEA results further reveal that the degraded QQ near 90∘90^{\circ} cannot be fully explained by power flow angle alone. Instead, as the propagation angle approaches 90∘90^{\circ}, the reduced thickness-shear excitation is accompanied by stronger unintended transverse displacement near the anchors, thereby enhancing acoustic energy leakage and lowering QQ. These results indicate that the orientation-dependent degradation of QQ in 128°Y-cut LN resonators, rather than the absolute QQ level, is strongly linked to orientation-dependent mode deformation and anchor-region energy leakage. This study provides experimental evidence and physical insight into anisotropic loss mechanisms in 128°Y-cut LN XBARs, offering design guidance for jointly optimizing k2k^{2}, QQ, and propagation orientation in high-frequency acoustic devices.

Acknowledgment

This work was completed at the Texas Nanofabrication Facility Microelectronics Research Center.

References

References

  1. [1]C. C. W. Ruppel, “Acoustic Wave Filter Technology—A Review,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 64, no. 9, pp. 1390–1400, Sep. 2017.DOI
  2. [2]R. Abdolvand, H. M. Lavasani, G. K. Ho, and F. Ayazi, “Thin-film piezoelectric-on-silicon resonators for high-frequency reference oscillator applications,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 55, no. 12, pp. 2596–2606, Dec. 2008.
  3. [3]V. Yantchev and I. Katardjiev, “Thin film Lamb wave resonators in frequency control and sensing applications: A review,” Journal of Micromechanics and Microengineering, vol. 23, no. 4, p. 043001, Mar. 2013.DOI
  4. [4]E. A. Wollack, A. Y. Cleland, R. G. Gruenke, Z. Wang, P. Arrangoiz-Arriola, and A. H. Safavi-Naeini, “Quantum state preparation and tomography of entangled mechanical resonators,” Nature, vol. 604, no. 7906, pp. 463–467, Apr. 2022.DOI
  5. [5]R. Ruby, “A Snapshot in Time: The Future in Filters for Cell Phones,” IEEE Microwave Magazine, vol. 16, no. 7, pp. 46–59, Aug. 2015.DOI
  6. [6]S. Gong, R. Lu, Y. Yang, L. Gao, and A. E. Hassanien, “Microwave Acoustic Devices: Recent Advances and Outlook,” IEEE Journal of Microwaves, vol. 1, no. 2, pp. 601–609, Apr. 2021.DOI
  7. [7]R. Lu, “Recent advances in high-performance millimeter-wave acoustic resonators and filters using thin-film lithium niobate,” Progress in Quantum Electronics, vol. 100–101, p. 100565, Mar. 2025.DOI
  8. [8]R. Lu and S. Gong, “RF acoustic microsystems based on suspended lithium niobate thin films: Advances and outlook,” Journal of Micromechanics and Microengineering, vol. 31, no. 11, p. 114001, Sep. 2021.DOI
  9. [9]G. Pillai and S.-S. Li, “Piezoelectric MEMS Resonators: A Review,” IEEE Sensors Journal, vol. 21, no. 11, pp. 12589–12605, Jun. 2021.DOI
  10. [10]M. Li, K. Yang, J. Fang, F. Lin, and C. Zuo, “A1-Mode Lamb Wave Resonator in 128° Y-Cut Lithium Niobate with Electromechanical Coupling Coefficient of 57%,” in 2024 IEEE Ultrasonics, Ferroelectrics, and Frequency Control Joint Symposium (UFFC-JS), Sep. 2024, pp. 1–4.DOI
  11. [11]J. Kramer, B. T. Bosworth, L. Matto, N. R. Jungwirth, O. Barrera, F. Bergmann, S. Cho, V. Chulukhadze, M. Goorsky, N. D. Orloff, and R. Lu, “Acoustic resonators above 100 GHz,” Applied Physics Letters, vol. 127, no. 1, p. 012204, Jul. 2025.DOI
  12. [12]O. Barrera, J. Kramer, L. Matto, V. Chulukhadze, S. Cho, M. E. Liao, M. S. Goorsky, and R. Lu, “50 GHz Piezoelectric Acoustic Filter,” IEEE Journal of Microwaves, vol. 6, no. 2, pp. 391–400, Mar. 2026.DOI
  13. [13]Y. Yang, R. Lu, L. Gao, and S. Gong, “10–60-GHz Electromechanical Resonators Using Thin-Film Lithium Niobate,” IEEE Transactions on Microwave Theory and Techniques, vol. 68, no. 12, pp. 5211–5220, Dec. 2020.DOI
  14. [14]J. Kramer, J. Campbell, T.-H. Hsu, I. Anderson, and R. Lu, “Cryogenic Q enhancement in 50 GHz piezoelectric resonators,” Applied Physics Letters, vol. 128, no. 10, p. 102205, Mar. 2026.
  15. [15]R. Tabrizian, M. Rais-Zadeh, and F. Ayazi, “Effect of phonon interactions on limiting the f.Q product of micromechanical resonators,” in TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference, Jun. 2009, pp. 2131–2134.
  16. [16]A. Hagelauer, R. Ruby, S. Inoue, V. Plessky, K.-Y. Hashimoto, R. Nakagawa, J. Verdu, P. de Paco, A. Mortazawi, G. Piazza, Z. Schaffer, E. T.-T. Yen, T. Forster, and A. Tag, “From Microwave Acoustic Filters to Millimeter-Wave Operation and New Applications,” IEEE Journal of Microwaves, vol. 3, no. 1, pp. 484–508, Jan. 2023.DOI
  17. [17]T. Anunsor, O. Barrera, J. Kramer, I. Anderson, Z. Yao, V. Chulukhadze, and R. Lu, “Practical Demonstrations of F3-Band Thin-Film Lithium Niobate Acoustic Filter Design,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 72, no. 12, pp. 1650–1662, Dec. 2025.
  18. [18]S. Gong and G. Piazza, “Design and Analysis of Lithium–Niobate-Based High Electromechanical Coupling RF-MEMS Resonators for Wideband Filtering,” IEEE Transactions on Microwave Theory and Techniques, vol. 61, no. 1, pp. 403–414, Jan. 2013.DOI
  19. [19]F. V. Pop, A. S. Kopchar, G. Vidal-Álvarez, and G. Piazza, “Investigation of Electromechanical Coupling and Quality Factor of X-Cut Lithium Niobate Laterally Vibrating Resonators Operating Around 400 MHz,” Journal of Microelectromechanical Systems, vol. 27, no. 3, pp. 407–413, Jun. 2018.DOI
  20. [20]S.-M. Wu, H. Yan, C.-B. Hao, Z.-H. Qin, S.-Y. Yu, and Y.-F. Chen, “K-Band LiNbO3 A3 Lamb-Wave Resonators With Through-Holes,” Journal of Microelectromechanical Systems, vol. 34, no. 2, pp. 164–173, Apr. 2025.DOI
  21. [21]M. Faizan and L. G. Villanueva, “Optimization of Inactive Regions of Lithium Niobate Shear Mode Resonator for Quality Factor Enhancement,” Journal of Microelectromechanical Systems, vol. 30, no. 3, pp. 369–374, Jun. 2021.DOI
  22. [22]J. Kramer and R. Lu, “A Generalized Acoustic Framework for Multilayer Piezoelectric Platforms,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 72, no. 9, pp. 1302–1311, Sep. 2025.DOI
  23. [23]Y. Liu, X. Xu, J. Li, and T. Wu, “High Figure-of-Merit 36Y-Cut LiNbO3 Lamb Wave Resonators With Dissipation Loss Optimization,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 72, no. 8, pp. 1021–1028, Aug. 2025.DOI
  24. [24]R. Lu, T. Manzaneque, Y. Yang, and S. Gong, “Exploiting parallelism in resonators for large voltage gain in low power wake up radio front ends,” in 2018 IEEE Micro Electro Mechanical Systems (MEMS), Jan. 2018, pp. 747–750.DOI
  25. [25]Y.-H. Song and S. Gong, “Arraying SH0 Lithium Niobate laterally vibrating resonators for mitigation of higher order spurious modes,” in 2016 IEEE 29th International Conference on Micro Electro Mechanical Systems (MEMS), Jan. 2016, pp. 111–114.DOI
  26. [26]Y. Yang, R. Lu, and S. Gong, “High Q Antisymmetric Mode Lithium Niobate MEMS Resonators With Spurious Mitigation,” Journal of Microelectromechanical Systems, vol. 29, no. 2, pp. 135–143, Apr. 2020.DOI
  27. [27]Y. Yang, L. Gao, R. Lu, and S. Gong, “Lateral Spurious Mode Suppression in Lithium Niobate A1 Resonators,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 68, no. 5, pp. 1930–1937, May 2021.DOI
  28. [28]R. Naik, J. Lutsky, R. Reif, and C. Sodini, “Electromechanical coupling constant extraction of thin-film piezoelectric materials using a bulk acoustic wave resonator,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 45, no. 1, pp. 257–263, Jan. 1998.DOI
  29. [29]R. Lu, M.-H. Li, Y. Yang, T. Manzaneque, and S. Gong, “Accurate Extraction of Large Electromechanical Coupling in Piezoelectric MEMS Resonators,” Journal of Microelectromechanical Systems, vol. 28, no. 2, pp. 209–218, Apr. 2019.DOI
  30. [30]J. Larson, P. Bradley, S. Wartenberg, and R. Ruby, “Modified Butterworth-Van Dyke circuit for FBAR resonators and automated measurement system,” in 2000 IEEE Ultrasonics Symposium. Proceedings. An International Symposium (Cat. No.00CH37121), vol. 1, Oct. 2000, pp. 863–868 vol.1.DOI
  31. [31]C. Tu, J. E.-Y. Lee, and X.-S. Zhang, “Dissipation Analysis Methods and Q-Enhancement Strategies in Piezoelectric MEMS Laterally Vibrating Resonators: A Review,” Sensors, vol. 20, no. 17, p. 4978, Jan. 2020.DOI
  32. [32]R. Jin, Z. Cao, M. Patel, B. Abbott, D. Molinero, and D. Feld, “An improved formula for estimating stored energy in a BAW resonator by its measured S11 parameters,” in 2021 IEEE International Ultrasonics Symposium (IUS). IEEE, 2021, pp. 1–5.DOI
  33. [33]R. Lu, T. Manzaneque, Y. Yang, M.-H. Li, and S. Gong, “Gigahertz Low-Loss and Wideband SO Mode Lithium Niobate Acoustic Delay Lines,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 66, no. 8, pp. 1373–1386, Aug. 2019.
  34. [34]I. E. Kuznetsova, B. D. Zaitsev, A. A. Teplykh, S. G. Joshi, and A. S. Kuznetsova, “The power flow angle of acoustic waves in thin piezoelectric plates,” IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control, vol. 55, no. 9, pp. 1984–1991, Sep. 2008.
  35. [35]R. Lu and S. Gong, “Power Flow Angles of GHz Propagating Acoustic Waves in Thin-Film Lithium Niobate,” in 2021 IEEE International Ultrasonics Symposium (IUS), Sep. 2021, pp. 1–4.DOI
  36. [36]D. Lee, S. Meyer, S. Gong, R. Lu, and K. Lai, “Visualization of acoustic power flow in suspended thin-film lithium niobate phononic devices,” Applied Physics Letters, vol. 119, no. 21, p. 214101, Nov. 2021.DOI
  37. [37]S. A. Chandorkar, M. Agarwal, R. Melamud, R. N. Candler, K. E. Goodson, and T. W. Kenny, “Limits of quality factor in bulk-mode micromechanical resonators,” in 2008 IEEE 21st International Conference on Micro Electro Mechanical Systems, Jan. 2008, pp. 74–77.DOI

Paper details

vlnc:W_ukbd2br8
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents