betaFeedback

WorksPhysics and Astronomy

Metahouse: noise-insulating chamber based on periodic structures

Abstract

Noise pollution remains a challenging problem requiring the development of novel systems for noise insulation. Extensive work in the field of acoustic metamaterials has led to occurrence of various ventilated structures which, however, are usually demonstrated for rather narrow regions of the audible spectrum. In this work, we further extend the idea of metamaterial-based systems developing a concept of a metahouse chamber representing a ventilated structure for broadband noise insulation. Broad stop bands originate from strong coupling between pairs of Helmholtz resonators constituting the structure. We demonstrate numerically and experimentally the averaged transmission -18 dB within the spectral range from 1500 to 16500 Hz. The sparseness of the structure together with the possibility to use optically transparent materials suggest that the chamber may be also characterized by partial optical transparency depending on the mutual position of structural elements. The obtained results are promising for development of novel noise-insulating structures advancing urban science.

Introduction

Acoustic metamaterials and phononic crystals have been subjects of keen scientific interest for a couple of decades as they provide novel routes towards efficient control of acoustic field [1, 2, 3, 4]. In addition to the realization of negative refractive index [5], superlenses [6, 7], holograms [8], and acoustic cloaks [9], recent advances include the development of non-reciprocal systems [10], topological insulators [11, 12], nonlinear [13], tunable [14], coding [15], and programmable metasurfaces [16]. Acoustic metasurfaces were also explored as potential platforms for analog computing [17] and, vice versa, advances in computer science and artificial intelligence boost design procedures to achieve desired properties of metamaterials and metasurfaces [18, 19, 20, 21]. Metamaterials can be also used as a platform to explore analogies of the quantum concepts, such as Hall effect [22, 23], spin properties [24, 25, 26, 27], skyrmions [28], and twistonics [29].

One of the developing branches in the field of acoustic metamaterials is dedicated to realization of novel noise-insulating systems. Increasing noise pollution in urban areas is one of the endangering trends affecting global health and ecological environment [30, 31, 32, 33, 34]. Solution of this problem requires the development of new methods and materials allowing broadband passive noise insulation. Conventionally used systems are typically represented by bulky structures imposing harsh engineering restrictions on buildings and constructions [35]. Frequency range of noise mitigation has to be compromised with mass and volume of the used materials. Moreover, some crucial properties like ventilation or optical transparency are usually incompatible with such systems.

Instead of the conventional mass-density law, reflection and attenuation of sound in metamaterials relies mostly on periodicity and shape of the structural elements rather than their material properties. One of the important options enabled by metamaterials is the possibility to implement structures allowing air flow [36, 37, 38, 39]. A variety of designs includes perforated membranes [40, 41], space coiling structures [42, 43, 44, 45, 46], and metacages [47, 48] have been presented. Nevertheless, despite the plethora of achievable physical effects, acoustic metamaterials rarely find real-life applications. These structures usually have complicated designs and a narrow operating range.

In this paper, we propose a noise-insulating ventilated metahouse chamber allowing access of light into the inner area. The chamber is designed to be simple for manufacturing and assembling. At the same time, the requirements for materials are easily met and the structure can be made of ecologically friendly and optically transparent materials. The chamber is based on coupled Helmholtz resonators with C-shaped cross-section and exploits band-gap formation as the main mechanism for sound insulation. The artistic illustration of the concept is presented in Figure 1. It is proposed that such structures may be incorporated into urban parks to create noise-free relaxation zones for visitors.

Metahouse concept

Figure 1. Metahouse concept. The Helmholtz resonators are shown with gray only for visual clearance and can be made of transparent materials. The inner space of the developed chamber is protected from acoustic noises within a broad audible spectral range. At the same time, the structure itself is ventilated and optically transparent. Two former parameters depend solely on the distance between the structural elements and their size, which also determine the spectral range of blocked noises.

We start with designing a 2D metamaterial-based periodic structure and tuning its parameters for maximization of the integral width of band-gaps in the audible spectral range. Then, we perform an experimental demonstration of stop-bands corresponding to band-gaps of the infinite system. Finally, we provide an experimental demonstration of a finite-size prototype of the metahouse chamber. All experimental results are verified by numerical simulations.

Results

Design of a unit cell

The chosen unit cell consists of two coupled Helmholtz resonators with C-shaped cross-section, as shown in Figure 2(a). Such resonators can be 3D printed or easily manufactured via simple mechanical processing of commercially available polymer pipes. Similar geometries were already considered for noise mitigation purposes [48, 49, 50] and we have just utilized the fact that local coupling between the resonators may increase the integral width of band gaps [51]. In this paper we consider only ΓX\Gamma X band-gaps since the implemented experimental realization of the semi-infinite structure implies that the incident plane wave has only kxk_x component. Performing the tuning of geometrical parameters, we have optimised the system to further increase the integral width of band-gaps fΓXf_{\Gamma X} defined as the sum of the widths of individual band-gaps [see Figs. 2(b) and 2(c)]:

Figure 2. Design of the unit cell. (a) Illustration of the considered unit cell consisting of two locally coupled Helmholtz resonators. Width of the unit cell is axa_x and the height is aya_y. The resonators are characterized by the inner radius rr and the outer radius RR. Slit width ww and distance between the resonators dd are tuning parameters. The resonators are rotated around their out-of-plane axes by the angles θ1\theta_1 and θ2\theta_2. Dashed red lines indicate reflection symmetry axes of the cell. (b) The corresponding reciprocal unit cell. (c) Arbitrary band diagram representing labeling of individual ΓX\Gamma X band-gaps used for calculation of the integral width of ΓX\Gamma X band-gaps fΓXf_{\Gamma X}.

fΓX=∑ifΓX(i)(1)f_{\Gamma X} = \sum_i f_{\Gamma X}^{(i)} \tag*{(1)}

where ii stays for the number of a band-gap and index ΓX\Gamma X indicates that the considered band-gaps lie within ΓX\Gamma X interval of the Brillouin zone [see Figure 2(b) and 2(c)]. Here it should be noted that summation is done over the band-gaps within the considered frequency ranges. For simplicity, we have considered a 2D geometry assuming that the resonators are infinite in the direction perpendicular to the surface of the cross-section.

Since the system is scalable, for the tuning procedure we have normalized all geometric parameters to the outer radius of the resonators RR. The size of the unit cell was fixed at values of ax/R=4.5a_x/R = 4.5 and ay/R=2.25a_y/R = 2.25. The inner radius of the resonators rr is fixed as r/R=0.905r/R = 0.905. The distance between the centers of resonators dd as well as the width of slits ww were varied as parameters directly affecting the local coupling. The frequencies are also normalized by R/cairR/c_{\mathrm{air}}, where cair=343c_{\mathrm{air}} = 343 m/s is the speed of sound in air.

The colormap shown in Figure 3(a) demonstrates the integral width of ΓX\Gamma X band-gaps fΓXf_{\Gamma X} as a function of ww and dd. Clearly, the presence of finite-size slits results in the increase of fΓXf_{\Gamma X}. At the same time, the dependence is nonlinear and there are two local maxima corresponding to the points with d/R=2.25d/R = 2.25, w/R=0.75w/R = 0.75 [point A, see Figure 3(b)] and d/R=2.4d/R = 2.4, w/R=1.55w/R = 1.55 [point B, see Figure 3(c)]. The corresponding band structures demonstrating large ΓX\Gamma X band-gaps are shown in Figure 3(d) and 3(e), respectively. It is also important to note that within the considered frequency range the structure may possess the features of a metamaterial as well as a phononic crystal. So there may be several mechanisms of band-gap formation involved.

Figure 3. Band structure and optimization. (a) Integral width of band-gaps as a function of slit width ww and distance between the resonators dd. Points A and B indicate two local maxima of the function fΓXf_{\Gamma X}, occurring near the points with w/R=0.75w/R = 0.75, d/R=2.25d/R = 2.25 and w/R=1.55w/R = 1.55, d/R=2.4d/R = 2.4, respectively. The corresponding unit cells are shown in panels (b) and (c). Note that the map is rescaled using a power-law relationship to provide better visualization. Band diagrams for the structures with such configurations are demonstrated in panels (d) and (e). Shaded green areas indicate the ΓX\Gamma X band-gaps.

Following the adjustment of slit widths and distances between the resonators, we analyze the effect of resonators’ rotation on the integral width of band-gaps. Figure 4 shows the integral width of band-gaps calculated for the range of rotational angles θ1\theta_1 and θ2\theta_2 [see Figure 4(a)]. Rotation of the resonators results in a pronounced decrease of fΓXf_{\Gamma X} in the vicinity of the point θ1=0∘\theta_1 = 0^\circ, θ2=180∘\theta_2 = 180^\circ, corresponding to the case of CC-like geometry. Such a reduction of the integral width of band-gaps is associated with the decrease of local coupling strength [51] which in the case of CC-like geometry is weak. In the Supplementary Information we demonstrate that the proposed geometry is indeed characterized by much stronger local coupling allowing increase of integral width of band gaps by nearly 30 % comparing to the CC-like geometry. Considering the point A, for CC-like geometry fΓXf_{\Gamma X} reduces by more than 20 % in comparison to the optimal case with θ1=θ2=0∘\theta_1 = \theta_2 = 0^\circ [see Figure 4(b)]. Similarly, for point B the corresponding reduction is about 15 % [see Figure 4(b)], however, there are configurations which are less beneficial. Figure 4 also demonstrates the robustness of the considered system against rotations of the resonators. Indeed, the calculations indicate that rotation within approximately 15∘15^\circ almost does not perturb values of fΓXf_{\Gamma X}. This fact is important for practical realization of the proposed structure since it allows to reduce requirements for mounting tolerances.

Rotation of the resonators, with panel (a) showing two resonators and panels (b) and (c) showing colormaps of band-gap width

Figure 4. Rotation of the resonators. The panel (a) illustrate the definition of the rotational angles θ1\theta_1 and θ2\theta_2. The strongly coupled geometry is characterized by θ1=θ2=0∘\theta_1 = \theta_2 = 0^\circ while the case of the CC-like geometry corresponds to θ1=0∘\theta_1 = 0^\circ, θ2=180∘\theta_2 = 180^\circ. The colormaps (b) and (c) show the integral width of band-gaps as a function of the rotational angles such that the resonators are characterized by (b) w/R=0.75w/R = 0.75, d/R=2.25d/R = 2.25 and (c) w/R=1.55w/R = 1.55, d/R=2.4d/R = 2.4. These parameters correspond to the points labeled in Figure 3 as A and B, respectively.

Experimental verification of stop-bands

To experimentally verify the presence of wide band-gaps, we consider a configuration of the structure corresponding to the point A in Figure 3. We imitate the semi-infinite structure, such that it is finite along one axis and infinite along the two other ones (see Methods section for details). The samples fabricated via 3D printing are shown in Figure 5(a) while the schematic view and photograph of the setup are demonstrated in Figure 5(b) and 5(c), respectively. Note that of instead the complete resonators we consider their halves utilizing the symmetry of the field distribution within the unit cell, as discussed in Methods section. The measurements were provided for the unit cell characterized by ax=240a_x = 240 mm and ay=120a_y = 120 mm such that the outer radius of the resonators is R=53R = 53 mm and the inner radius is r=48r = 48 mm. Slit width is then w=40w = 40 mm and the distance between the resonators is d=120d = 120 mm. The considered frequency range is 200 – 2060 Hz.

Figure 5. Transmission of semi-infinite structure. (a) Photograph of the samples characterized by R=53R = 53 mm, r=48r = 48 mm, w=40w = 40 mm, and height h=60h = 60 mm. (b) Schematic picture and (c) photo of the experimental setup. (d) Band diagram for the system with the unit cell with ax=240a_x = 240 mm, ay=120a_y = 120 mm and d=120d = 120 mm. For convenience, two frequency axes are shown, the normalized one and the one in conventional units. Measured and simulated (for a 2D system) transmission spectra for (e) one, (f) two, and (g) three pairs of coupled Helmholtz resonators. Experimentally obtained values are shown by red lines, while the numerical results are demonstrated by the blue lines. Green shaded areas indicate ΓX\Gamma X band-gaps of the corresponding infinite 2D structure.

The obtained transmission spectra are demonstrated in Figure 5(e) – Figure 5(g), where the blue lines correspond to numerical simulations (for a 2D system) and the red lines represent the experimental measurements. The green shaded areas indicate the ΓX\Gamma X band-gaps of the equivalent infinite 2D system shown in Figure 5(a). For convenience, two frequency axes are shown, the normalized (top) and the un-normalized (bottom). The measurements are provided for 1, 2, and 3 pairs of resonators in order to explicitly demonstrate the evolution of stop-bands with respect to a change in the structure thickness. In accordance with a simple intuition, increasing the number of pairs results in broadening of the stop-bands. It should be noted that, unlike the noise barrier consisting of a single Helmholtz resonator [48], a wide stop-band can be observed even for the one-pair thickness. Practically, for the case of 3 pairs of coupled resonators, the stop-bands cover more than 80 % of the considered spectral range. But even for one pair the stop-bands are quite large and pronounced, mostly going below −15 dB.

Noise-insulating chamber

The finite-size prototype of the metahouse chamber is shown in Figure 6(a). It is an axially symmetric structure consisting of 30 radially oriented arrays with 3 pairs of resonators each. The outer radius of the chamber is 300 mm and the inner one is 120 mm. Height of the structure is 60 mm. The resonators are characterized by R=6.7R = 6.7 mm, r=6r = 6 mm, and w=5w = 5 mm. Along the arrays, the distance between centers of the resonators (in xyxy plane) is d=15d = 15 mm. The transmission spectrum is shown in Figure 6(c) with experimental values indicated by red line and the numerical simulations (for a 2D system) by the blue one. Shaded green areas indicate ΓX\Gamma X band-gaps of the corresponding infinite 2D system considered in the previous Section.

Figure 6. Transmission of the metahouse chamber. (a) The manufactured prototype of the metahouse chamber. There are 30 arrays forming a toroid with the outer radius 300 mm and the inner one 120 mm. Each array consists of 3 pairs of resonators with R=6.7R = 6.7 mm, r=5.5r = 5.5 mm, and w=5w = 5 mm. The distance between centers of the resonators along the axis of an array is d=15d = 15 mm. (b) Photograph of the experimental setup. The microphone is located inside the chamber and the loudspeaker is placed at one of the walls. (c) Measured transmission spectrum (red line) and the corresponding numerical values obtained for the equivalent 2D chamber (blue line). Shaded green areas correspond to the equivalent infinite 2D periodic structure [see Figure 3].

The measurements were performed in a box with the walls covered by foam rubber pyramids [see Fig. 6(b)]. However, it has to be noted that the height of the box is 60 mm while the wavelength of generated waves is smaller than this value for almost whole range of spectra (see Methods section). Since all of the structures are uniform in the vertical direction, it is unlikely that the higher order modes would be excited. Still, assuming that the system is not ideal it may be not a perfect equivalent of the 2D system which explains some differences between

the numerical and experimental results.

Discussion

The developed metahouse chamber demonstrates good insulating properties with the average transmission of −18-18 dB in the broad spectral range from 1500 to 16500 Hz Figure 6(c). The average value was calculated as the arithmetic mean within the spectral range. Ventilation properties as well as partial optical transparency are defined by geometric properties of the structure. Analysis of the air flow is presented in the Supplementary Information. While the concept was demonstrated for the case when the resonators are located quite close to each other, the structure may be optimized to increase the sparseness. For example, numerical calculations done for the finite-size metacage with the number of arrays reduced by a half also demonstrate reasonable noise-insulation properties with the average transmission −7-7 dB (see Supplementary Information). Tuning of parameters and optimization of the structure may enhance the results allowing proper air flow and optical transparency implying compromise between sparseness and sound transmission. In addition, the structure can be made of optically transparent materials, such as the commercially available PLA filament for 3D printers [52]. The possibility to achieve simultaneous air ventilation with optical transparency is a unique feature of the developed structure resulting from the proposed design. In Table I we also provide values of acoustic impedance for several materials which may be used for construction of the metahouse chamber. It is important to highlight that the range of possible materials is huge and hence the conventional widespread materials can be used.

Methods

Numerical simulations

All numerical simulations are performed for 2D systems using finite element method (FEM) via COMSOL Multiphysics, Pressure Acoustics module. Throughout the calculations, the boundaries of resonators are assumed to be sound-hard walls. Such an approximation is justified by high impedance contrast between the material of resonators and air. For example, the acoustic impedance of polypropylene is about 2.4 MRayl [54]

which is several orders higher than for air. Similar contrasts of impedances is also observed for other materials which can be used for construction of the chamber, see Table I. It is also should be mention that any thermo-viscous boundary effects are neglected, since there are no narrow channels in the considered structures.

MaterialZZ (MRayl)Reference
Polylactic acid (PLA)2.56 – 2.77[53]
Polypropylene2.3 – 2.4[54]
Polymethyl methacrylat3.14 – 3.69[55]

Table I. Acoustic impedance ZZ of some materials which can be used for construction of the metahouse chamber.

The semi-infinite structure is modelled as an array made of NN halved resonators placed into a 2D waveguide with sound hard walls. The distance between the walls is equal to ay/2a_y/2. The ends of the waveguide are modelled as perfectly matched layers (PML). The incident plane wave with amplitude p0p_0 propagates along the direction of periodicity (xx-axis, parallel to the walls of the waveguide). Pressure values are calculated at the sample point located at the distance xt=15x_t = 15 mm from the rightmost resonator. Parameters of the resonators correspond to those of the fabricated samples.

In the model for the finite-size case the chamber is placed into the 2D box in which all walls are PML such that the distance between the walls is 1210 mm and 510 mm along xx and yy axis, respectively. The structure is located at the center of the waveguide and the sample point is placed at the center of the structure. Incident waves with amplitude p0p_0 are generated by a point source located near one of the walls. Geometric size of the 2D chamber correspond to the parameters of the manufactured structure.

Experimental setup

The experimental measurements are provided inside a waveguide with rectangular cross-section. The walls and the bottom of the waveguide are made of aluminum with thickness of 15 mm. The lid is made of 6 mm thick transparent plexiglass. The height of the inner cross-section of the waveguide is fixed and equal to 60 mm. However, the width is adjustable and can be varied from 0 to 650 mm via displacement of one of the walls. The loudspeaker (Visaton BF 45/4) is located at one end of the waveguide and the microphone (BOYA BY-PVM1000) is placed at the other one. While the full length of the waveguide is 135 cm, the distance between the microphone and the loudspeaker is 107 cm. The rest of the waveguide’s length is occupied by two pieces of foam rubber, each 14 cm long. The loudspeaker and the microphone are embedded into these inserts.

The microphone is directly connected to a USB audio interface Roland Rubix22. To connect the loudspeaker to the same sound card we use an amplifier based on the Yamaha YDA138-E microchip. The sound card itself is connected to a personal computer via USB interface. Control of signal generation and recording is realized via specially developed software based on the Python programming language (in particular, generation and recording of signals exploit the sound device module [56]).

To imitate semi-infinite structure in the experiment we consider an array consisting of NN pairs of coupled resonators. Proper boundary conditions — namely, sound hard walls at geometrical symmetry axes — allow to imitate periodicity along the two other axes (yy and zz axes). The numerical 2D model corresponds to a structure infinite in the zz direction, while in the experiment it is mimicked by keeping the waveguide width and height smaller than λ/2\lambda/2 for the considered spectral range. The operational range of the setup for the case of the semi-infinite structure is 200–2100 Hz. In order to imitate an infinite structure, all walls have to be totally reflective. At the same time, symmetry of the unit cell and of field distributions within it have to be preserved. Therefore, we select the size of the cross-section such that it’s width and height are smaller than the smallest wavelength in the spectrum of a generated signal. Otherwise, the walls have to be perfectly symmetric and elements within the waveguide have to be centered ideally, which is hardly achievable.

In order to increase the reliable frequency range in the waveguide below λ/2\lambda/2, we therefore only use half instead of full resonators. Such modification is valid since it does not violate symmetry of the structure. The resonators were manufactured by 3D printing (PLA filament). Note, that to simplify placement of resonators inside the waveguide, there are small place-holders in the slits of the resonators.

All measurements were conducted for generated chirped signal with the frequency changing from 200 to 2100 Hz. For each measurement the signal was generated several times and then the measured spectra were averaged in Fourier space. Sampling frequency was always fixed at 44100 Hz. Following the conventional definition, the transmission was defined as

T=20log⁡10(ptrpref)(2)T = 20\log_{10}\left(\frac{p_{\mathrm{tr}}}{p_{\mathrm{ref}}}\right) \tag*{(2)}

where prefp_{\mathrm{ref}} is a pressure amplitude of the wave in the absence of a structure (reference signal) and ptrp_{\mathrm{tr}} is a pressure amplitude of the transmitted wave.

The measurement of transmission for the finite-size chamber were conducted in the same waveguide, as for the case of semi-infinite structure. However, the distance between the walls was increased to 650 mm. The walls and the ends were covered by foam rubber pyramids (with height 50 mm and square base 50 by 50 mm). The chamber was located at the center of the waveguide such that microphone (BOYA BY-M1) was placed inside the structure (at the center). All other elements and connections between them were the same as for the semi-infinite system. The procedure of signal generation and averaging also remained the same, however the frequency range was changed to be from 1500 to 16500 Hz.

References

Acknowledgements

The authors thank Aleksandr Kalganov for the help with design and assembly of the experimental setup and Mikhail Kuzmin for sample fabrication. The authors also thank Nikita Olekhnov for fruitful discussions and suggestions. This research was supported by Priority 2030 Federal Academic Leadership Program.

Author contributions

M.K. designed the structure, experimental samples, and the experimental setup, and performed experimental measurements. S.K. and M.K. provided numerical calculations. S.K. participated in the experimental setup assembly and measurements. A.M., Y.B., S.M., and D.P. provided guidance on all aspects of the work. A.B. suggested the idea and supervised the project. All authors contributed to writing and editing of the manuscript.

Competing interests

The authors declare no competing interests.

A Coupled Helmholtz resonators

Since it is claimed that the broadband noise-insulation is achieved due to the strong local coupling of the Helmholtz resonators we would like to provide a proof that the coupling is indeed strong. For that we consider a pair of the resonators in a free space and calculate pressure inside one of them, assuming that the incident wave with the amplitude p0=1p_0 = 1 Pa propagates along the xx-axis [see Figure 7(a) and Figure 7(d)]. The resulting spectra are shown in Figure 7(b) and Figure 7(e). The splitting of the Helmholtz resonance decreasing with the increase of the distance between the resonators is the manifestation of the coupling between the resonators. For the case of the considered geometry [Figure 7(d)], the splitting is much larger than for the CC-like one [Figure 7(a)]. In addition, the field distribution in the proposed geometry is fundamentally different from the CC-like geometry since it has additional mirror symmetry with respect to yy-axis. Hence, the split Helmholtz resonance occurs as in-phase and out-of-phase excitation of the resonators characterized by symmetric and anti-symmetric field distributions, respectively [see Figure 7(c) and Figure 7(f)].

Coupling between two resonators

Figure 7. Coupling between two resonators. The system consists of a pair of the Helmholtz resonators located in a free space, such that the incident pressure field propagates along the xx-axis. Two cases are considered, namely (a) the CC-like geometry and (d) the strongly coupled resonators. Panels (b) and (e) shows corresponding frequency spectra calculated at the sampling point located at the center of the rightmost resonator (the red dot). The spectral distances between the split resonances for the case of d/R=2.25d/R = 2.25 are indicated by Δ\Delta. Distributions of the scattered pressure field for the case of d/R=2.25d/R = 2.25 are shown in panels (c) and (f); the frequencies correspond to the resonances indicated by the vertical dashed lines on the spectra.

In the case of an infinite arrays, the local coupling results in the pronounced increase of the integral width of band-gaps [51]. Figure 8 demonstrates the difference between the band structures for the infinite arrays of resonators with zero slits (which are just circular pipes), CC-like geometry and strongly coupled resonators. Indeed, the introduction of slits to the pipes results in a formation of an additional band [see Figure 8(b)] as well as the additional band-gap, as consequence. Further, an enhancement of the local coupling leads to the formation of two more Γ\Gamma-XX band-gaps. In this case, the out-of-phase excitation of the Helmholtz resonance corresponds to the flat band indicating strong localization of the field inside the resonators as well as the absence of coupling between the neighboring couples. In turn, the other mode, which is flat only within the ΓX\Gamma X interval, is associated with the in-phase excitation of the Helmholtz resonance.

Band diagrams and field distributions for pipes, CC-like geometry, and strongly coupled resonators

Figure 8. Deformation of band structure. Band diagrams for the case of (a) pipes, (b) CC-like geometry (c) strongly coupled resonators. Shaded green areas indicate the Γ\Gamma-XX band-gaps. The following parameters of the structures are used: (b) w/R=0.75w/R = 0.75; (c) w/R=0.75w/R = 0.75, d/R=2.25d/R = 2.25; for each panel r/R=0.905r/R = 0.905. Field distributions shown in panel (d) correspond to the labeled blue points in the band diagrams.

To trace the deformation of band structure caused by introduction of slit and the consequent enhancement of the local coupling, we consider field distributions within the unit cells (at Γ\Gamma-point). For the structure made of pipes there are two modes with zero frequency. One of them, labelled as a1-1 in Figure 8(d), is a structural resonance, typical for periodic structures. This mode is present in both other band diagrams [b1 in Figure 8(b) and c1 in Figure 8(c)]. Another mode, labelled as a1-2, is the flat band with zero frequency actually corresponding to the eigenmode of a Helmholtz resonator with zero slits. As soon as the slit is introduced, this band deforms and shifts to the area of larger frequencies. Hence, the mode a1-2 of pipe arrays can be associated with the mode b2, which is a Helmholtz resonance of a CC-like structure. When the coupling is enhanced, this mode splits on two [c2 and c3 in Figure 8(c)]. In this case, the field distribution patterns within a single unit cell of the periodic structure are similar to those observed for a single pair of resonators presented in Figure 7(f). The anti-symmetric mode, labelled as c3 is perfectly localized within the resonators meaning that there is no coupling between neighbouring pairs, which is the reason why the corresponding band is flat. Also, there is another additional mode c4, which may be considered as the additional structural resonance resulting from the deformation of the unit cell.

Another type of modes are the modes of a circular pipe, which also correspond to flat bands in each of the diagrams. For the case of pipes, these are two degenerate modes a2-1 and a2-2. When the slit is introduced, the degeneracy lifts due to the break of symmetry, but the mode with similar field distribution remains in the system. Then, the structure with the strong coupling is characterized by two similar nearly-degenerate modes (c6-1 and c6-2). Finally, the mode c5 is the structural resonance, such that similar resonances are present in all of the considered structures, but at higher frequencies.

B Ventilation properties of the structures

In order to demonstrate the ventilation properties of the proposed structures, we calculate the laminar air flow with the help of COMSOL Multiphysics software package. For all cases, the normal inflow velocity was taken to be U0=10−4U_0 = 10^{-4} m/s and the no-slip wall boundary condition was used. The results shown in Figure 9(a) demonstrate that the semi-infinite structure does not violate the air flow, suggesting that the structure might be suitable for noise insulation of ventilated ducts.

Air flow through the designed structures

Figure 9. Air flow through the designed structures. (a) Semi-infinite structure in the duct, (b) metahouse chamber and (c) sparse metahouse chamber considered in the main text. For each panel left boundary is considered to be an inlet port with normal inflow velocity U0=10−4 m/sU_0 = 10^{-4}\,\mathrm{m/s}. The direction of the flow is shown by black arrows while the color indicates its velocity UU.

Switching to the case of metahouse chamber, Figure 9(b) shows that the laminar flow inside the structure is quite weak. Flow velocity at the center of the chamber is about 10−510^{-5} m/s, which is one order smaller than the inflow velocity. Hence, the initial structure for which the experimental measurements were done is poorly ventilated. At the same time, considering the use of such structures in the real-world conditions of urban parks, it can be hypothesised that air will definitely penetrate inside the chamber which at the same time may provide some protection from wind. Increasing the sparseness enhances the air flow inside the structure, as is seen in Figure 9(c). However, in this case the flow velocity inside the chamber is higher than the inlet one. The reason for this is the cone-like narrowing of the channels in-between the arrays of the resonators resulting in the flow acceleration. While the sparsed structure has a half of the initial number of the resonators, its noise-insulating properties are still quite reasonable. In this case the numerically calculated average transmission is about −7-7 dB as the Figure 10 shows. The conclusion which can be made from the Figure 9 and Figure 10 is that it is possible to find a compromise between the ventilating and noise-insulating properties of the proposed metahouse structure by varying its sparseness.

Figure 10. Transmission of the sparse metahouse chamber. Schematic representation of the (a) initial [see Figure 6 from the main text] and (b) sparse structures. (c) Simulated transmission spectra for both cases. Average transmission for the sparse structure is −7-7 dB and for the initial structure is −25-25 dB.

References

  1. [1]Cummer, S. A., Christensen, J. & Alù, A. Controlling sound with acoustic metamaterials. Nature Reviews Materials 1, 1–13 (2016).DOI
  2. [2]Zangeneh-Nejad, F. & Fleury, R. Active times for acoustic metamaterials. Reviews in Physics 4, 100031 (2019).
  3. [3]Liu, J., Guo, H. & Wang, T. A Review of Acoustic Metamaterials and Phononic Crystals. Crystals 10, 305 (2020).DOI
  4. [4]Liao, G. et al. Acoustic Metamaterials: A Review of Theories, Structures, Fabrication Approaches, and Applications. Advanced Materials Technologies 6, 2000787 (2021).DOI
  5. [5]Kaina, N., Lemoult, F., Fink, M. & Lerosey, G. Negative refractive index and acoustic superlens from multiple scattering in single negative metamaterials. Nature 525, 77–81 (2015).DOI
  6. [6]de Rosny, J. & Fink, M. Overcoming the Diffraction Limit in Wave Physics Using a Time-Reversal Mirror and a Novel Acoustic Sink. Physical Review Letters 89, 124301 (2002).pubmed.ncbi.nlm.nih.gov/12225085
  7. [7]Li, J., Fok, L., Yin, X., Bartal, G. & Zhang, X. Experimental demonstration of an acoustic magnifying hyperlens. Nature Materials 8, 931–934 (2009).DOI
  8. [8]Zhang, J., Tian, Y., Cheng, Y. & Liu, X. Acoustic holography using composite metasurfaces. Applied Physics Letters 116, 030501 (2020).DOI
  9. [9]Chen, H. & Chan, C. T. Acoustic cloaking in three dimensions using acoustic metamaterials. Applied Physics Letters 91, 183518 (2007).DOI
  10. [10]Guo, X., Ding, Y., Duan, Y. & Ni, X. Nonreciprocal metasurface with space-time modulation. Light: Science & Applications 8, 123 (2019).DOI
  11. [11]Peng, Y.-G. et al. Experimental demonstration of anomalous Floquet topological insulator for sound. Nature Communications 7, 13368 (2016).DOI
  12. [12]Xue, H. et al. Observation of an acoustic octupole topological insulator. Nature Communications 11, 2442 (2020).
  13. [13]Fang, X., Wen, J., Bonello, B., Yin, J. & Yu, D. Ultra-low and ultra-broad-band nonlinear acoustic metamaterials. Nature Communications 8, 1288 (2017).DOI
  14. [14]Chen, S. et al. A Review of Tunable Acoustic Metamaterials. Applied Sciences 8, 1480 (2018).DOI
  15. [15]Xie, B. et al. Coding Acoustic Metasurfaces. Advanced Materials 29, 1603507 (2017).DOI
  16. [16]Tian, Z. et al. Programmable Acoustic Metasurfaces. Advanced Functional Materials 29, 1808489 (2019).
  17. [17]Zuo, S., Wei, Q., Tian, Y., Cheng, Y. & Liu, X. Acoustic analog computing system based on labyrinthine metasurfaces. Scientific Reports 8, 10103 (2018).DOI
  18. [18]Donda, K. et al. Ultrathin Acoustic Absorbing Metasurface Based on Deep Learning Approach. Smart Materials and Structures (2021).DOI
  19. [19]Xu, Z.-X., Zheng, B., Yang, J., Liang, B. & Cheng, J.-C. Machine-Learning-Assisted Acoustic Consecutive Fano Resonances: Application to a Tunable Broadband Low-Frequency Metasilencer. Physical Review Applied 16, 044020 (2021).DOI
  20. [20]Gao, N., Wang, M., Cheng, B. & Hou, H. Inverse design and experimental verification of an acoustic sink based on machine learning. Applied Acoustics 180, 108153 (2021).DOI
  21. [21]Ding, H. et al. Deep Learning Enables Accurate Sound Redistribution via Nonlocal Metasurfaces. Physical Review Applied 16, 064035 (2021).arxiv.org/abs/2108.01568
  22. [22]Zhou, W., Su, Y., Muhammad, Chen, W. & Lim, C. W. Voltage-controlled quantum valley Hall effect in dielectric membrane-type acoustic metamaterials. International Journal of Mechanical Sciences 172, 105368 (2020).DOI
  23. [23]Fan, X.-D. & Zhang, L. Acoustic orbital angular momentum Hall effect and realization using a metasurface. Physical Review Research 3, 013251 (2021).DOI
  24. [24]Shi, C. et al. Observation of acoustic spin. National Science Review 6, 707–712 (2019).
  25. [25]Long, Y. et al. Realization of acoustic spin transport in metasurface waveguides. Nature Communications 11, 4716 (2020).DOI
  26. [26]Yang, C., Tan, Y.-T., Chen, H. & Ren, J. Real spin angular momentum and acoustic spin torque in a topological phononic crystal. Journal of Applied Physics 129, 135106 (2021).DOI
  27. [27]Wang, S. et al. Spin-orbit interactions of transverse sound. Nature Communications 12, 6125 (2021). 2105.13558.DOI
  28. [28]Ge, H. et al. Observation of Acoustic Skyrmions. Physical Review Letters 127, 144502 (2021).DOI
  29. [29]Gardezi, S. M., Pirie, H., Carr, S., Dorrell, W. & Hoffman, J. E. Simulating twistonics in acoustic metamaterials. 2D Materials 8, 031002 (2021).DOI
  30. [30]Stansfeld, S. A. & Matheson, M. P. Noise pollution: Non-auditory effects on health. British Medical Bulletin 68, 243–257 (2003).pubmed.ncbi.nlm.nih.gov/14757721
  31. [31]Singh, N. & Davar, S. C. Noise Pollution-Sources, Effects and Control. Journal of Human Ecology 16, 181–187 (2004).DOI
  32. [32]Goines, L. & Hagler, L. Noise pollution: A modern plague. Southern Medical Journal 100, 287–294 (2007).pubmed.ncbi.nlm.nih.gov/17396733
  33. [33]Kunc, H. P. & Schmidt, R. The effects of anthropogenic noise on animals: A meta-analysis. Biology Letters 15, 20190649 (2019).DOI
  34. [34]Münzel, T., Sørensen, M. & Daiber, A. Transportation noise pollution and cardiovascular disease. Nature Reviews Cardiology 18, 619–636 (2021).DOI
  35. [35]Hopkins, C. Sound Insulation (Routledge, London, 2007).
  36. [36]Xu, Z.-X. et al. Topology-Optimized Omnidirectional Broadband Acoustic Ventilation Barrier. Physical Review Applied 14, 054016 (2020).DOI
  37. [37]Sun, M., Fang, X., Mao, D., Wang, X. & Li, Y. Broad-band Acoustic Ventilation Barriers. Physical Review Applied 13, 044028 (2020).
  38. [38]Kumar, S., Xiang, T. B. & Lee, H. P. Ventilated acoustic metamaterial window panels for simultaneous noise shielding and air circulation. Applied Acoustics 159, 107088 (2020).DOI
  39. [39]Dong, R., Mao, D., Wang, X. & Li, Y. Ultra-broadband Acoustic Ventilation Barriers via Hybrid-Functional Metasurfaces. Physical Review Applied 15, 024044 (2021).DOI
  40. [40]Ma, G., Yang, M., Yang, Z. & Sheng, P. Low-frequency narrow-band acoustic filter with large orifice. Applied Physics Letters 103, 011903 (2013).DOI
  41. [41]Langfeldt, F., Kemsies, H., Gleine, W. & von Estorff, O. Perforated membrane-type acoustic metamaterials. Physics Letters A 381, 1457–1462 (2017).DOI
  42. [42]Cheng, Y. et al. Ultra-sparse metasurface for high reflection of low-frequency sound based on artificial Mie resonances. Nature Materials 14, 1013–1019 (2015).DOI
  43. [43]Chen, Z. et al. An open-structure sound insulator against low-frequency and wide-band acoustic waves. Applied Physics Express 8, 107301 (2015).DOI
  44. [44]Zhang, H.-L. et al. Omnidirectional ventilated acoustic barrier. Applied Physics Letters 111, 203502 (2017).DOI
  45. [45]Ghaffarivardavagh, R., Nikolajczyk, J., Anderson, S. & Zhang, X. Ultra-open acoustic metamaterial silencer based on Fano-like interference. Physical Review B 99, 024302 (2019).DOI
  46. [46]Yu, X. et al. Sound transmission through a periodic acoustic metamaterial grating. Journal of Sound and Vibration 449, 140–156 (2019).DOI
  47. [47]Shen, C., Xie, Y., Li, J., Cummer, S. A. & Jing, Y. Acoustic metacages for sound shielding with steady air flow. Journal of Applied Physics 123, 124501 (2018).DOI
  48. [48]Melnikov, A. et al. Acoustic metamaterial capsule for reduction of stage machinery noise. The Journal of the Acoustical Society of America 147, 1491–1503 (2020).DOI
  49. [49]Melnikov, A. et al. Acoustic meta-atom with experimentally verified maximum Willis coupling. Nature Communications 10, 3148 (2019).DOI
  50. [50]Elford, D. P., Chalmers, L., Kusmartsev, F. V. & Swallowe, G. M. Matryoshka locally resonant sonic crystal. The Journal of the Acoustical Society of America 130, 2746–2755 (2011).
  51. [51]Hu, G., Tang, L., Das, R., Gao, S. & Liu, H. Acoustic metamaterials with coupled local resonators for broadband vibration suppression. AIP Advances 7, 025211 (2017).DOI
  52. [52]Matos, B. D. M. et al. Evaluation of commercially available polylactic acid (PLA) filaments for 3D printing applications. Journal of Thermal Analysis and Calorimetry 137, 555–562 (2019).DOI
  53. [53]Parker, N. G., Mather, M. L., Morgan, S. P. & Povey, M. J. W. Longitudinal acoustic properties of poly(lactic acid) and poly(lactic- co -glycolic acid). Biomedical Materials 5, 055004 (2010).DOI
  54. [54]Selfridge, A. R. Approximate Material Properties in Isotropic Materials. IEEE Transactions on Sonics and Ultrasonics 32, 381–394 (1985).DOI
  55. [55]Carlson, J. E., van Deventer, J., Scolan, A. & Carlander, C. Frequency and temperature dependence of acoustic properties of polymers used in pulse-echo systems. In IEEE Symposium on Ultrasonics, 2003, vol. 1, 885–888 Vol.1 (2003).DOI
  56. [56]Play and Record Sound with Python. spatialaudio.net (2021).

Paper details

vlnc:W_vumrv5jp
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents