betaFeedback

WorksPhysics and Astronomy

Hydrogen-induced modification of the local charge density in MnSb2_2Te4_4

Abstract

We investigate the effects of ionic hydrogen (H+^+) intake on the occupied and unoccupied states of MnSb2_2Te4_4, a van der Waals magnetic material. Using angle-resolved photoemission spectroscopy (ARPES) and time-resolved ARPES, combined with resonant and core level photoemission, we reveal that hydrogen binds near specific lattice sites, locally redistributing charge density and reshaping the valence band spectral weight. While the band gap and picosecond carrier dynamics show only minor changes upon hydrogenation, the conduction band exhibits a striking stoichiometry-dependent response. These findings indicate that hydrogen interacts strongly with the intrinsic defects in the lattice, acting as a selective dopant in MnSb2_2Te4_4. Our work provides a spectroscopic basis for using hydrogen as a tool for the control of the electronic and magnetic properties in layered 2D materials.

INTRODUCTION

Intrinsic magnetic topological insulators (MTIs), with the general formula MA2B4\mathrm{MA}_{2}\mathrm{B}_{4} (M\mathrm{M} = transition-metal or rare-earth, A\mathrm{A} = Bi or Sb, B\mathrm{B} = Te, Se or S), naturally combine magnetism and topology into a van der Waals structure, enabling the emergence of exotic quantum phases. In two dimensions this manifests as Chern insulators, hosting the quantum anomalous Hall effect (QAHE), while in three dimensions it can give rise to axion insulator states [1]. Among MTIs, MnBi2Te4\mathrm{MnBi}_{2}\mathrm{Te}_{4} (MBT) has been established as an n-type antiferromagnetic (AFM) topological insulator (TI) [2, 3, 4, 5], while substitution of Bi with Sb leads to an n-to-p carrier type transition accompanied by more diverse magnetic and electronic properties [3, 6] that are highly sensitive to intrinsic defects and dopants.

Like MBT, MnSb2Te4\mathrm{MnSb}_{2}\mathrm{Te}_{4} (MST) crystallizes in a rhombohedral layered structure composed by Te(1)-Sb-Te(2)-Mn-Te(2)-Sb-Te(1) septuple layers separated by van der Waals (vdW) gaps, as shown in Figure 1a. In the a-b plane, atoms are arranged on a triangular lattice [7, 8], conventionally described using hexagonal axes with a correspondingly hexagonal surface Brillouin zone (Figure 1b). The two sibling compounds share the same dominant defect type: Mn-Bi/Sb antisites. In MST antisite disorder is considerably more pronounced because of the similar electronegativities and atomic sizes of Mn and Sb [9]. In MBT, the concentration of MnBi and BiMn antisites generally remains below 5% and 20%, respectively, while in MST, MnSb and SbMn antisites can reach 15% and 40% [10, 11].

Figure 1. (a) Crystal structure of MnSb2Te4\mathrm{MnSb}_{2}\mathrm{Te}_{4}. Te(1) and Te(2) are the two inequivalent Te sites within the septuple layer. (b) Brillouin Zone of the crystal. (c) and (d) Band dispersion measured at T=16T = 16 K with hν=25h\nu=25 eV and P and S polarization respectively along Γ−M\Gamma- M. (e) Band dispersions measured at T=77T=77 K using 95 eV photon energy and p-polarized light for the as-grown FM MST sample and (f) the hydrogenated sample. (g) Comparison of the k-integrated intensity between the two samples. The arrows indicate the energies where a change in spectral weight is recorded.

This abundance in antisites has immediate implications on the electronic and magnetic properties of MST. The presence of Mn atoms in the Sb layers, introduce competing exchange interactions along the c-axis, perpendicular to the atomic layers, allowing MST to stabilize in either a ferromagnetic (FM) or an antiferromagnetic (AFM) ground state depending on the stoichiometry [11, 12, 13]. In particular, Mn-rich samples, which contain higher concentration of antisite defects, tend to favor the FM state [8, 10]. As for the topological character of MST, it remains in active debate, with numerous theoretical studies reporting both topological and trivial phases [7, 10, 14, 15, 16, 17], a discrepancy largely attributed to the material’s sensitivity to antisite defects. Defects, thus, make MST highly tunable, but also challenging to control.

Hydrogenation offers a way to exploit this sensitivity. Tamanna et al. [18] showed that hydrogen intake and release is a reversible, non-destructive process capable of tuning both the magnetic and topological properties of FM MST. H+\mathrm{H}^{+} incorporation decreases the majority p-type carrier density and switches the long-range magnetic order from FM to AFM, while subsequent release through mild annealing tilts the Weyl nodes lying on the kx−kyk_x-k_y plane. Although hydrogenation is widely practiced in semiconductor applications [19, 20, 21] and, more recently, on a variety of other systems [22, 23, 24, 25], its effect on the band structure of a magnetic quantum material has never been directly observed.

Here, we provide the first spectroscopic study of H+\mathrm{H}^{+} intake in FM and AFM MST and we show its effects on the electronic band structure via a combination of photoemission techniques. Using angle-resolved photoemission spectroscopy (ARPES) and time-resolved ARPES (trARPES), supported by core-level and resonant photoemission, we show that the incorporation of hydrogen in the crystal structure manifests as a redistribution of spectral weight between Mn-related bands, accompanied by a subtle changes in the band gap and electron dynamics. This behavior points to hydrogen locally ેદ modifying the bonding character at charged defect sites by passivating them. Samples of different stoichiometry responded differently to hydrogenation, an effect that we attribute to the link between the total Mn content and the concentration of Mn-Sb defects in MST. Taken together, these results establish how hydrogen reshapes the electronic structure through its interaction with the intrinsic defects in MST and point to hydrogen as a reversible tool for engineering the properties of quantum materials.

METHODS

High quality MnSb2_2Te4_4 single crystals were grown by flux method [18]. The hydrogenation step was implemented according to the protocol established in [18] and [26]. The immersion into the aqueous HCl solution was carried out for 46 and 93 hours for the FM (Mn0.93_{0.93}Sb2.07_{2.07}Te4_4) and the AFM (Mn0.77_{0.77}Sb2.25_{2.25}Te4_4) samples respectively. For all the photoemission-based experiments, i.e., ARPES, trARPES and XPS, the samples were prepared in situ by cleaving under high vacuum (<1×10−10< 1 \times10^{-10} mbar) at 300 K.

ARPES experiments where carried out at the CAS-SIOPEE beamline of SOLEIL synchrotron, at low temperatures (T=15-20 K), with an overall energy resolution of 30 meV. μ\mu-XPS and μ\mu-ARPES measurements where performed the ANTARES beamline of synchrotron SOLEIL at T = 75 K. The beam was focused down to 5 μ\mum using a capillary mirror, enabling higher photon flux and access to a broad range of photon energies [27].

The trARPES measurements where carried out at 130 K using the FemtoARPES experimental setup [28], pumping with pulses centered 1.55 eV and with 20μ\muJ/cm2^2 and 400μ\muJ/cm2^2 of fluence. For the case of hydrogenated samples, the lowest fluence was used in order to minimize heating effects at the surface. The fourth harmonic, centered at 6.2 eV and generated by sum frequency generation in BBO crystals (β\beta-BaB2_2O4_4) was used as a probe either at p- or s-polarization. The temporal resolution, determined by the cross-correlation between pump and probe was ≈100\approx100 fs. The total energy resolution was 100 meV as determined by measuring the Fermi edge on a polycrystalline Au sample, while the angular resolution was better than 0.1o^o[28].

RESULTS & DISCUSSION

Figure 1c and Figure 1d show the low-energy band structure of FM MnSb2_2Te4_4 measured along Γˉ−Mˉ\bar{\Gamma}-\bar{M} using p- and s-polarized light of hν=25h\nu= 25 eV. The valence band crosses the Fermi level EFE_F, indicating strong p-type behavior and and is qualitatively similar to the one of relative compounds in the family MnSb2_2Te4_4/ (Sb2_2Te3_3)n_n with SL (septuple layer) terminations [13, 29]. A clear polarization dependence is observed. The bands indicated with arrows in Figure 1d are visible only with s-polarization, whereas the V-shaped band is observed with both s- and p. This behavior originates from photoemission matrix-element effects, suggesting that both in-plane and out-of-plane orbitals contribute to the low-energy electronic structure. The pzp_z orbitals of Te and Sb dominate the valence band and the conduction band close to EFE_F, and are responsible for the band inversion and the appearance of topological surface states in the case of TI MST [1]. In addition, even though Mn d-bands are usually deeper in conduction band, as they are highly localized, they contribute to the lower energy bands through Te-Mn-Te hybridization [9, 30, 31].

Using higher photon energies, we probed the full Brillouin zone along the Γˉ−Mˉ\bar{\Gamma}-\bar{M} direction and compared the as-grown and hydrogenated FM sample. Figure 1e and Figure 1f show the band structures of both samples acquired with p-polarized light at 95 eV photon energy. At first glance, no striking differences are visible between the two samples. In both cases the Mn 3d flat band is clearly visible at 3.2 eV binding energy, characteristic of the highly localized Mn 3d orbitals. To better resolve the subtle differences between the two, the EDCs taken as an average over the momentum range indicated by the black lines in Figure 1e,Figure 1f is shown in Figure 1g. With the intake of H+^+, we observe a transfer of spectral weight from EBE_B=8.5 eV towards the bands next to the Fermi level and at the proximity of the Mn 3d band which appears to be slightly broader. The total sum of the areas below the integrated profiles equals zero (A1+A2+A3=0A_1 + A_2 + A_3 = 0), indicating the conservation of the spectral weight in the specific region of the Brillouin zone. This suggests that hydrogenation modifies locally the charge density around specific lattice sites, altering the hybridization between the Mn 3d and the Te/Sb p orbitals.

Additionally, upon H+^+ intake, the valance band remains intact with respect to the Fermi level EFE_F, with no evident shift in the band positions. According to [18], when H+^+ is diffused in the structure, it donates electrons to the system, effectively reducing its p-type character. It is therefore expected that this effective electron doping would shift the chemical potential away from the valence band [32], manifesting as a rigid shift of the bands toward lower binding energies. Such behavior is typical of alkali metal doping. The evaporation of alkali metals on the surface, such as K or Cs, creates a two-dimensional electron gas (2DEG) at the surface that acts as a reservoir of itinerant electrons. This accumulation of charge at the surface builds up a uniform dipolar electric field, resulting in band bending and the apparent rigid shift of the bands [33, 34]. However, such behavior is not observed here. In contrast, H+^+ is distributed into the bulk and thus, no macroscopic field is built up at the surface, keeping the chemical potential pinned, consistent with the absence of any observable shift of the bands in our data.

Identifying the orbital character of the observed bands is key to understanding how hydrogen incorporation modifies the density of states at specific energies. Direct experimental evidence on that question are obtained through resPES experiments, thanks to its enhanced element- and orbital-sensitivity. Figure 2a shows a series of valence band spectra for FM MST obtained by resonant excitation at photon energies near the Mn 2p→3d2p \rightarrow3d absorption edge in b. These measurements reflect the partial DOS, projected on the Mn 3d orbitals, revealing two main components, namely at 0.5 eV and 3.2 eV below EFE_F, and a broad feature in the range between -6 eV and -9 eV of binding energies.

Resonant photoemission spectra in ferromagnetic MnSb2Te4

Figure 2. Resonant photoemission in ferromagnetic (FM) MST. The photon energy is tuned near the Mn L3L_3 absorption edge.

Coming back to Figure 1c, it is now clear that the bands affected by hydrogen are the ones related to the Mn 3d states. Interestingly, the localized states forming the flat band at -3.2 eV binding energy are not affected by hydrogen. This points to hydrogen primarily modifying the delocalized states that participate in the hybridization with Te or Sb orbitals, forming dispersive bands, rather than atomic-like ones. To further develop this argument, hydrogen enters the lattice as a charged species

H+H^{+}, while the lattice itself finally relaxes into a charge-neutral state. For this state to be thermodynamically stable, H+H^+ should not exist interstitially as a free uncompensated proton but rather create bonds with the atoms of the host lattice. Bond formation is possible only at negatively-charged sites, i.e. at acceptor-like defects. In MST such defects are primarily Mn or Sb vacancies (VMnV_{\mathrm{Mn}} and VSbV_{\mathrm{Sb}}) and MnSb_{\mathrm{Sb}} antisite defects [9]. Within a more general framework, such behavior reflects hydrogen’s amphoteric nature: in semiconductors H+H^+ can occupy different charge states during the diffusion process, passivating defects or dangling bonds by donating or accepting charge depending on the local bonding environment [19, 20, 21].

Band gap and out-of-equilibrium dynamics

Having established the effects of H+H^+ intake on the equilibrium band structure, we investigate next the impact on the unoccupied states by means of trARPES measurements. Here, FM MST (Mn0.93_{0.93}Sb2.07_{2.07}Te4_4) is compared with an AFM sample, less rich in Mn (Mn0.77_{0.77}Sb2.25_{2.25}Te4_4). Through these experiments, the correlation between doping effects and the amount of antisite defects present in the structure are examined. Figure 3 shows the transient carrier population ΔI/I0\Delta I/I_0 and the subsequent relaxation of the unoccupied states in the two samples before and after hydrogenation. For both samples, FM and AFM (Figure 3a and Figure 3e), upon the arrival of the pump pulse at zero delay, electrons are promoted into two distinct energy regions: one right above the EFE_F (E1E_1) where the valence band crossing was previously observed and another at higher energy, corresponding to the bulk conduction band (E2E_2). It is noted that in region E1E_1 a finite population below EFE_F is observed, pointing towards the presence of transient electrostatic effects acting on the surface. Similar features are observed in all samples studied here but are not considered further in the present analysis. Upon pumping, the excited electron population rapidly thermalises within ≈150\approx150 fs via electron-electron intraband scattering, reaching the minimum of the conduction band (CBM) at 0.55 eV and 0.5 eV binding energy in the FM and the AFM sample, respectively. From there, phonon-assisted recombination follows on a time scale of ≈2.4\approx2.4 ps, similar for the two cases, as shown in Figure 3c and Figure 3g. The recombination of the excited electrons occurs between the holes right below EFE_F, as indicated by the similar dynamics of the holes in magenta. The relatively high fitting uncertainty arises from the weak transient intensity recorded within this limited momentum range, accessible with the 6.2 eV probe (±0.17\pm0.17 Å−1^{-1}). The faster relaxation from the E1E_1 state (in black) compared to E2E_2 is consistent with its proximity to the valence states, facilitating the recombination with the photoexcited holes close to EFE_F. The size of the band gap, defined here as the energy separation between E1E_1 and E2E_2, is 0.554 eV for the FM and 0.487 eV for the AFM samples, respectively. These values are consistent with the work of Xi et al. [35] where a 7.2 eV probe was used, although here the gap in FM MST is slightly smaller. The 100 meV difference in the gap size of the FM and the AFM samples reflects the difference in Mn content and, consequently, the concentration of antisite defects [10].

trARPES measurements of as-grown and hydrogenated MnSb2Te4 samples

Figure 3. trARPES measurements taken with P-polarized probe pulses at T=130T = 130 K. (a) kk-integrated spectra of the as-grown MST as a function of pump-probe delay obtained by subtracting at each energy the equilibrium EDC at negative delays, I0I_0. Red and blue correspond to the gain and loss of electrons with respect to the equilibrium. The integration was done in a window Δk=0.3\Delta k = 0.3 Å−1^{-1} centered at Γ. (b) Similar to (a) for the hydrogenated sample. (c) and (d) time evolution of the spectral weight obtained by integrating over 0.10.1 eV, as indicated by the colored brackets in (a) and (b) respectively. (e) and (f) similar to (a) and (b) for the AFM sample. (g) and (h) similar to (c) and (d) for the AFM sample.

Regarding the effect of H+H^+ intake, the recombination dynamics remain unchanged in the FM sample, while they become slower by 1 ps in the AFM sample (Figure 3d and Figure 3h). For surface excited electrons, defects are primarily elastic scattering centers and hence they contribute to increasing the scattering rate (faster decay time). Considering that hydrogen heals intrinsic defects in MST, it is expected to decrease their total concentration and therefore intensify the presence of hot electrons at the conduction band minimum. Assuming also that the HCl dosing time is sufficient to reach saturation, the effect in AFM should be substantially larger than in FM, as is indeed observed. Regarding the gap size, a reduce by ≈30\approx30 meV is observed upon hydrogenation in both cases, though this effect remains subtle.

Hydrogen-induced spectral weight redistribution

The k-integrated spectra for static and trARPES are presented in Figure 4. For both FM and AFM samples it is evident that hydrogenation results in the increase of spectral weight in the low energy band structure below EFE_F, particularly at the V1V_1 and V2V_2 regions as shown in Figure 4(a) and (Figure 4b). From DOS calculations it is known that the valence band maximum is dominated by the partially hybridized Te 5p with the Mn 3d states, while the lowest part of the conduction band is a mixture of Mn 3d and Sb 5p states [9, 30, 31]. As discussed above, static ARPES measurements demonstrate that during the diffusion process, H+H^+ interacts with negatively charged defects, resulting in the addition of states in the low-energy valence band, irrespectively of the magnetic ground state of the sample.

Figure 4. (a) kk-integrated photoemission yield along M‾−Γ‾−M‾\overline{M}-\overline{\Gamma}-\overline{M} of the FM as-grown and hydrogenated sample extracted from (Ekin,kx,ky)(E_{\mathrm{kin}}, k_x, k_y) maps. (b) Similar for the AFM sample. (c) kk-integrated intensity of FM and hydrogenated FM. The curve was obtained at Δτ\Delta\tau delay where the intensity signal of the conduction band minimum is maximum. (d) Similar for the as-grown AFM and hydrogenated samples.

The effect on the unoccupied states, shown in Figure 4c and Figure 4d, is even more striking. The presented EDCs are extracted from the transients shown in Figure 4, at pump-probe delay, where the conduction band minimum intensity is maximized for each sample. In the FM sample, hydrogenation leads to the decrease of spectral weight at E2E_2 by half relative to the as-grown sample. At a striking contrast, in the AFM case the effect is reversed and more pronounced, showing three times higher gain upon hydrogenation.

Such effects in the unoccupied states indicate a change in the number of states around the conduction band minimum, similar to what is observed in the valence band. Up to now there has been strong evidence that H+H^+ modifies the Sb-Te-Mn hybridization chain, suggesting that it preferably stabilizes near the highly electronegative Te sites which participate in the octahedral coordination of both Sb and Mn. In general, H+H^+ is expected to locate itself around negatively charged defects and thereby passivating them. One type of defects, proposed in the work of Tamanna et al. [18], is dangling Mn-Te bonds, associated with the under-coordinated and negatively charged MnSb_{\mathrm{Sb}} antisites [9] (Mn at an Sb site), located close to the van der Waals gap. The exposed negative charge, expected near the Te atom, makes these sites suitable for H+^+ to bind to. However, this mechanism alone, is insufficient to explain the opposite trends between the two samples. Since both measurements where performed in the paramagnetic phase, where no spin-split bands are expected, the only distinction between the two as-grown samples is their stoichiometry, and consequently the concentration of their intrinsic defects. At this point, we should consider that MST has a rich landscape of intrinsic charged defects, not limited to Mn-Sb antisites, whose formation energies differ between Mn-rich and Mn-poor samples [9]. Therefore, the preferential H+^+ sites may depend on stoichiometry in a more complex manner, calling for a more detailed theoretical support in order to fully understand the underlying mechanisms taking place.

Core level characterization

XPS measurements on the as-grown FM and hydrogenated MST samples (Figure 5) provide direct evidence that hydrogen modifies the chemical and electronic environment around specific lattice sites, supporting our interpretation.

Figure 5. X-ray photoelectron spectroscopy (XPS) in ferromagnetic (FM) as-grown and hydrogenated MST. (a) Te 4d4d and Sb 4d4d core levels measured with 95 eV photon energy, (b) Mn 2p2p, (c) Te 3d3d and (d) Sb 3d3d core levels measured with 850 eV photons. The Shirley background is subtracted from all the spectra.

The Mn 2p2p spectra of Figure 5a show four main peaks: 2p3/22p_{3/2} and 2p1/22p_{1/2} spin-orbit components (1/1′) with branching ratio 1/2, and their satellite peaks (2/2′), originating from charge transfer between the 3d3d shell of Mn and the outer shell of Te during the photoemission process. Peak 1/1′ consists of two peaks, corresponding to Mn2+^{2+} in the Mn-Te bond and to Mn atoms with reduced valence due to broken Mn-Te bonds [8, 36]. Upon hydrogenation, the main components shift to lower binding energy, indicating increased electron density around the Mn sites. The satellites (2/2′) become more pronounced without undergoing any shift, pointing to a modification of the metal (Mn) to ligand (Te) hybridization. The Te 3d3d spectra of Figure 5b decompose into two peaks, attributed to the two inequivalent Te sites in the unit cell, namely Te atoms located adjacent to the van der Waals gap Te(1) and Te atoms neighboring the Mn layer Te(2). Upon hydrogen intake, these components shift relative to one another, leading to an apparent narrowing of the overall Te 3d3d feature. This indicates that hydrogen modifies the local chemical environment of the two Te sites in a site-dependent manner, consistent with a change in the Mn-Te bonding environment. This behavior is consistent with the high electronegativity of the favoring H+^+ coordination close to the Te sites [18, 26]. Additionally, the Sb 3d3d spectra in Figure 5c consist of two components, labeled 1(1′) and 2(2′), separated by 1.2 eV within each spin-orbit doublet. Although the higher binding energy component resembles the spectral signature of oxidized Sb, this assignment is unlikely, since UHV cleavage conditions prevented any exposure to air. This component is therefore tentatively attributed to SbMn_{\mathrm{Mn}} antisites. Upon hydrogenation, its intensity decreases without an appreciable energy shift, suggesting that hydrogen modifies or passivates the local environment associated with these antisites. Finally, Figure 5d shows the 4d Te and Sb core levels at a kinetic energy corresponding to higher surface sensitivity: the comparison with the 3d peaks detected in a more bulk sensitive mode confirms that the double features in the core levels of Figure 5b and c are related to bulk effects on Te and Sb atoms.

CONCLUSIONS

To conclude, we showed that hydrogen interacts with the acceptor-like defects in MST, compensating for their excess negative charge. In particular, our results reveal that hydrogen preferably binds to defects related to Mn and Te lattice sites, therefore affecting the local Sb-Te-Mn hybridization network, as evidenced by the changes in the valence and conduction bands and the core-level spectra. Remarkably, H+ affects differently the FM and AFM samples, with opposing trends in the spectral weight change of the conduction band. Behind the observed behavior lies a nontrivial interaction mechanism which calls for future investigation. Overall, our work highlights the novelty and rich phenomenology of hydrogen incorporation as a controlled and effective way to manipulate the electronic properties of quantum systems.

Acknowledgments

We acknowledge financial support and of the Region Île de France via (FemtoARPES2.0 project N. EX079194). We thank synchrotron SOLEIL for providing beamtime under proposals 20250616 and 20252090.

References

References

  1. [1]J. Li, Y. Li, S. Du, Z. Wang, B. L. Gu, S. C. Zhang, K. He, W. Duan, and Y. Xu, Science Advances 5, 1 (2019).
  2. [2]Y. J. Chen, L. X. Xu, J. H. Li, Y. W. Li, H. Y. Wang, C. F. Zhang, H. Li, Y. Wu, A. J. Liang, C. Chen, S. W. Jung, C. Cacho, Y. H. Mao, S. Liu, M. X. Wang, Y. F. Guo, Y. Xu, Z. K. Liu, L. X. Yang, and Y. L. Chen, Physical Review X 91, 1 (2019).
  3. [3]B. Chen, F. Fei, D. Zhang, B. Zhang, W. Liu, S. Zhang, P. Wang, B. Wei, Y. Zhang, Z. Zuo, J. Guo, Q. Liu, Z. Wang, X. Wu, J. Wang, X. Xie, W. Chen, Z. Sun, S. Wang, Y. Zhang, M. Zhang, X. Wang, F. Song, H. Zhang, D. Shen, and B. Wang, Nature Communications 10 (2019).
  4. [4]H. Li, S. Y. Gao, S. F. Duan, Y. F. Xu, K. J. Zhu, S. J. Tian, J. C. Gao, W. H. Fan, Z. C. Rao, J. R. Huang, J. J. Li, D. Y. Yan, Z. T. Liu, W. L. Liu, Y. B. Huang, Y. L. Li, Y. Liu, G. B. Zhang, P. Zhang, T. Kondo, S. Shin, H. C. Lei, Y. G. Shi, W. T. Zhang, H. M. Weng, T. Qian, and H. Ding, Physical Review X 91 (2019).
  5. [5]P. Swatek, Y. Wu, L. Wang, K. Lee, B. Schrunk, J. Yan, and A. Kaminski, Physical Review B 101 (2020).
  6. [6]J. Zhang, C. Z. Chang, Z. Zhang, J. Wen, X. Feng, K. Li, M. Liu, K. He, L. Wang, X. Chen, Q. K. Xue, X. Ma, and Y. Wang, Nature Communications 2 (2011).
  7. [7]T. Murakami, Y. Nambu, T. Koretsune, G. Xiangyu, T. Yamamoto, C. M. Brown, and H. Kageyama, Physical Review B 100, 195103 (2019).
  8. [8]H. Li, Y. Li, Y. Lian, W. Xie, L. Chen, J. Zhang, Y. Wu, and S. Fan, Science China Materials 65, 477 (2022).
  9. [9]J. Xiong, Y. H. Peng, J. Y. Lin, Y. J. Cen, X. B. Yang, and Y. J. Zhao, Materials 16 (2023).
  10. [10]Y. Liu, L. L. Wang, Q. Zheng, Z. Huang, X. Wang, M. Qi, Y. Wu, B. C. Chakoumakos, M. A. McGuire, B. C. Sales, W. Wu, and J. Yan, Physical Review X 11, 21033 (2021).
  11. [11]X. Hu, H. He, Z. Guo, T. Kamiya, and J. Wu, ACS Nano 18, 738 (2024).
  12. [12]D. Y. Yan, M. Yang, P. B. Song, Y. T. Song, C. X. Wang, C. J. Yi, and Y. G. Shi, Physical Review B 103 (2021).
  13. [13]M. Xi, Y. Zhang, W. Zhou, F. Chen, D. Jia, H. Gou, T. Qian, and H. Lei, The journal of physical chemistry letters 16, 9507 (2025).
  14. [14]S. V. Eremeev, I. P. Rusinov, Y. M. Koroteev, A. Y. Vyazovskaya, M. Hoffmann, P. M. Echenique, A. Ernst, M. M. Otrokov, and E. V. Chulkov, Journal of Physical Chemistry Letters 12, 4268 (2021).
  15. [15]L. Zhou, Z. Tan, D. Yan, Z. Fang, Y. Shi, and H. Weng, Physical Review B 102, 85114 (2020).
  16. [16]P. Li, J. Yu, Y. Wang, and W. Luo, Physical Review B 103, 155118 (2021).
  17. [17]L. Chen, D. Wang, C. Shi, C. Jiang, H. Liu, G. Cui, X. Zhang, and X. Li, Journal of Materials Science 55, 14292 (2020).
  18. [18]A. N. Tamamanna, A. Lakra, X. Ding, E. Buzi, K. Park, K. Sobczak, H. Deng, G. Sharma, S. Tewari, and L. Krusin-Elbaum, Nature Communications 15 (2024).
  19. [19]A. Kiyoi, Y. Nishiya, Y. Matsushita, and T. Umeda, Communications Materials 7 (2026).
  20. [20]S. M. Myers, M. I. Baskes, H. K. Birnbaum, J. W. Corbett, G. G. DeLeo, S. K. Estreicher, E. E. Haller, P. Jena, N. M. Johnson, R. Kirchheim, S. J. Pearton, and M. J. Stavola, Rev. Mod. Phys. 64, 559 (1992).
  21. [21]S. J. Percott, J. W. Corbett, and T. S. Shi, Applied Physics A 43, 153 (1987).
  22. [22]D. C. Elias, R. R. Nair, T. M. G. Mohiuddin, S. V. Morozov, P. Blake, M. P. Halsall, A. C. Ferrari, D. W. Boukhvalov, M. I. Katsnelson, A. K. Geim, and K. S. Novoselov, New Series 323, 610 (2009).
  23. [23]K. Shibuya and A. Sawa, Advanced Electronic Materials 2 (2016).
  24. [24]M. Wang, X. Sui, Y. Wang, Y. H. Juan, Y. Lyu, H. Peng, T. Huang, S. Shen, C. Guo, J. Zhang, Z. Li, H. B. Li, N. Lu, A. T. N’Diaye, E. Arenholz, S. Zhou, Q. He, Y. H. Chu, W. Duan, and P. Yu, Advanced Materials 31 (2019).
  25. [25]Z. Li, Y. Lyu, Z. Ran, Y. Wang, Y. Zhang, N. Lu, M. Wang, M. Sassi, T. D. Ha, A. T. N’Diaye, P. Shafer, C. Pearce, K. Rosso, E. Arenholz, J. Y. Juang, Q. He, Y. H. Chu, W. Luo, and P. Yu, Advanced Functional Materials 33 (2023).
  26. [26]H. Deng, L. Zhao, K. Park, J. Yan, K. Sobczak, A. Lakra, E. Buzi, and L. Krusin-Elbaum, Nature Communications 13, 1 (2022).
  27. [27]J. Avila, S. Lorcy, and P. Dudin, Journal of Electron Spectroscopy and Related Phenomena 266 (2023).
  28. [28]J. Faure, J. Mauchain, E. Papalazarou, W. Yan, J. Pinon, M. Marsi, and L. Perfetti, Review of Scientific Instruments 83 (2012).
  29. [29]S. Huan, S. Zhang, Z. Jiang, H. Su, H. Wang, X. Zhang, Y. Yang, Z. Liu, X. Wang, N. Yu, Z. Zou, D. Shen, J. Liu, and Y. Guo, Physical Review Letters 126 (2021).
  30. [30]J. Q. Yan, S. Okamoto, M. A. McGuire, A. F. May, R. J. McQueeney, and B. C. Sales, Physical Review B 100 (2019).
  31. [31]S. V. Eremeev, M. M. Otrokov, and E. V. Chulkov, Journal of Alloys and Compounds 709, 172 (2017).
  32. [32]L. Zhao, M. Konczakowski, H. Deng, I. Korzhovska, M. Begliarbekov, Z. Chen, E. Papalazarou, M. Marsi, L. Perfetti, A. Hruban, A. Woloś, and L. Krusin-Elbaum, Nature Communications 7, 10957 (2016).
  33. [33]H. Pinto and A. Markevich, Beilstein Journal of Nanotechnology 5, 1842 (2014).
  34. [34]J. Zhang, T. D. P. Sohier, M. Casula, Z. Chen, J. Caillaux, E. Papalazarou, L. Perfetti, L. Petaccia, A. Bendounan, A. Taleb-Ibrahimi, D. Santos-Cottin, Y. Klein, A. Gauzzi, and M. Marsi, Nano Letters 23, 1830 (2023).
  35. [35]M. Xi, F. Chen, C. Gong, S. Tian, Q. Yin, T. Qian, and H. Lei, Journal of Physical Chemistry Letters 13 (2022).
  36. [36]R. J. Iwanowski, M. H. Heinonen, and B. Witkowska, Journal of Alloys and Compounds 491, 13 (2010).

Paper details

vlnc:W_wkr86tee
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 14

downloads · 2

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents