betaFeedback

WorksPhysics and Astronomy

A model of grain growth in UN integrating molecular dynamics, phase-field modeling, and uncertainty quantification

Abstract

Grain growth kinetics and grain-boundary (GB) properties in uranium mononitride (UN) are investigated through an integrated multiscale framework combining molecular dynamics (MD), phase-field modeling, and surrogate-assisted uncertainty quantification. MD simulations yield GB energies for 27 symmetric tilt boundaries from 0–2000~K, which are consistent with available DFT values. The average GB energy is nearly temperature-independent below 1000~K and increases at higher temperatures. A mechanistic pore-drag model applied to the only available grain growth dataset for actinide nitrides yields a mobility reduction factor of s≈0.93s \approx 0.93–0.990.99, statistically indistinguishable from unity, confirming that pore drag is negligible under the experimental conditions. The intrinsic GB mobility is therefore extracted directly from the effective mobility, yielding M0=2.05×10−15M_0 = 2.05\times10^{-15}~m4^4/(J⋅\cdots) and QM=0.89Q_M = 0.89~eV. Phase-field simulations conducted from 1500–2000~K confirm normal curvature-driven grain growth, with grain size distributions converging to the Hillert-like form. A surrogate-assisted global sensitivity analysis—combining principal component analysis, Gaussian process regression, and Sobol decomposition—reveals that the mobility prefactor M0M_0 dominates output variance at all times, followed by the activation energy QMQ_M, while the GB energy γγ contributes minimally. These results establish the first quantitative grain growth framework for UN and identify the reduction of uncertainty in M0M_0 and QMQ_M as the highest-priority target for future experimental efforts.

Introduction

Uranium mononitride (UN) stands out as a strong candidate for advanced nuclear fuels because of its exceptional characteristics: high fissile-material density, excellent thermal conductivity, broad compatibility with various cladding options, and the prospect of prolonged fuel residence times [1, 2]. However, several factors continue to impede its widespread adoption. These include the intricate nature of its fabrication processes, the substantial expense associated with enriching 15N{}^{15}\mathrm{N}, and a pronounced vulnerability to oxidation at elevated temperatures [1, 2]. Although some studies attempted to give a mechanistic understanding of some interesting phenomena in UN, e.g., paramagnetism [3], high-temperature specific heat [4, 5], dislocation motion [6], thermal creep [7], diffusivity under irradiation [8, 9], and swelling [10, 11], many aspects of its microstructural response remain unexplored due to a scarcity of experimental studies and a limited understanding of the underlying mechanisms. In this context, the kinetics and mechanisms of grain growth in UN, a key microstructural process, have not yet been systematically explored.

In polycrystalline materials, grain boundaries (GBs) migrate to reduce total free energy, collectively leading to grain growth. This phenomenon is typically studied under isothermal conditions [12]. GB migration may be driven by GB energy, elastic energy, or thermal gradients [13], with curvature-driven grain growth being the dominant mechanism under typical conditions. Grain growth and GB mobility are inherently interconnected and have almost always been studied concurrently. Kaoumi et al. [14, 15] proposed a model based on thermal-spike morphology to describe grain growth under irradiation in pure metals. Powers and Glaeser [16] reviewed grain growth and GB mobility in ceramics, highlighting the effects of solute drag, pore-boundary interactions, liquid phases, and anisotropy on microstructural evolution. For nuclear fuels, French and Bai [17] conducted an atomistic study to investigate GB mobility in γ\gamma-U. Additionally, there exist several experimental [12], atomistic [18], and mesoscale [13, 19] studies on grain growth and GB mobility for UO2\mathrm{UO}_2. Cheniour et al. [20] measured GB mobility in U3Si2\mathrm{U}_3\mathrm{Si}_2 and conducted a phase-field model of its grain growth using the MOOSE framework [21, 22]. For UN, however, only the experimental study by Ronchi and Sari [23] tried to quantify thermal grain growth in actinide nitrides, which was conducted on (U,Pu)N(\mathrm{U},\mathrm{Pu})\mathrm{N} rather than pure UN. Johnson and Lopes [24] prepared UN by spark plasma sintering and observed that grain rotation and coalescence are the dominant mechanisms of grain growth in UN during sintering. However, no attempt was made to quantify this behavior.

An important parameter that is needed to perform mesoscale grain evolution simulations is the GB energy and its dependence on temperature and, possibly, misorientation. Molecular dynamics (MD) simulations allow us to study the static and dynamic properties of GBs at a moderate computational cost, whereas alternative computational methodologies, e.g., DFT and ab initio MD, are limited by the requirements of large supercells and long simulation times, respectively, for the study of GB properties. Bicrystal models of tilt GBs have been utilized in MD to study the structure and energetics of GBs in Cu and Al [25, 26], Fe [27], and U3Si2\mathrm{U}_3\mathrm{Si}_2 [28], for example. Only the DFT study by Wang et al. [29] quantified the GB energy of UN. The calculation was done for only two symmetric tilt GBs, Σ5(310)[001]\Sigma5(310)[001] and Σ5(210)[001]\Sigma5(210)[001], at 0 K with no attempt to find the minimum energy structure of the GB using rigid body translations.

In this work, MD is used to calculate the GB energy for 27 symmetric tilt GBs in the temperature range of 0–2000 K. Then, a method is proposed to estimate the drag-free GB mobility of UN from the phenomenological grain growth formula. The estimated GB energy and mobility are utilized in a phase-field model of isothermal curvature-driven grain growth. Finally, a parametric study is performed to measure the sensitivity of the simulation output (average grain size) to uncertainties in the input parameters (GB energy and GB mobility).

Methods

Grain growth formalism

The velocity vv of a GB at a given location is described by [19, 30]:

v=dRdt=M[F−P]+,(1)v = \frac{dR}{dt} = M\left[F-P\right]^{+}, \tag*{(1)}

where RR is the local GB radius of curvature, MM is the GB mobility, FF is the driving force per unit area, and PP is the resistive force per unit area. The functional operator [x]+\left[x\right]^{+} equals xx when x>0x > 0 and 0 otherwise [19]. The driving force due to GB curvature is given by [20]:

F=γR,(2)F = \frac{\gamma}{R}, \tag*{(2)}

where γ\gamma is the GB energy. While GB properties are anisotropic, the overall grain growth behavior is often unaffected by this anisotropy [19], justifying the use of average GB properties and grain sizes. Assuming a geometric relation between the average grain size DD and the average curvature radius Rˉ\bar{R}, given by D=α1/2RˉD = \alpha^{1/2}\bar{R} [20], the grain growth rate can be approximated as:

dDdt≈αMγD,(3)\frac{dD}{dt} \approx\alpha M\frac{\gamma}{D}, \tag*{(3)}

where α=1\alpha= 1 for three-dimensional (3D) growth and α=1/2\alpha= 1/2 for two-dimensional (2D) growth [19]. MM and γ\gamma are the GB mobility and GB energy as previously defined. Integrating under the assumption of constant MM and γ\gamma gives:

D2−D02=2αMγt,(4)D^{2} - D_{0}^{2} = 2\alpha M\gamma t, \tag*{(4)}

where D0D_{0} is the initial average grain size. In addition to the power law of (4), a key feature of isothermal curvature-driven grain growth is that, after reaching steady-state, the grain-size distribution exhibits time self-similarity, most commonly resembling a lognormal or Hillert distribution [30, 31].

Although this ideal model holds for ultrapure materials close to their melting point [32], deviations are frequently observed experimentally due to resistive forces. To account for these complexities, the following semi-empirical model is used:

Dn−D0n=Kt,(5)D^{n} - D_{0}^{n} = Kt, \tag*{(5)}

where KK is the growth rate constant and nn is an empirically fitted exponent, typically between 2 and 4 [32], influenced by porosity, impurities, and residual stresses. Experimental data frequently suggest n=3n = 3, especially in porous materials [32, 33]. When n=2n = 2, the model aligns with the ideal case, yielding:

K=2αMγ.(6)K = 2\alpha M\gamma. \tag*{(6)}

For n>2n > 2, KK becomes a function of additional factors, including temperature-gradient-driven forces, porosity-induced resistance, and other microstructural features [16].

Grain-boundary energy

All MD calculations performed in this work utilize the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) software package [34] using a 1 fs time step and the Tseplyaev [35] and Kocevski [36] interatomic potentials. Periodic boundary conditions (PBCs) are applied to all supercells. The Atomsk code [37] is used to generate bicrystals by the Voronoi tessellation method. The OVITO software package [38] is used for supercell visualization and analysis.

The energy of the GB (per unit area) is a complex function of the five degrees of freedom of the GB and is often plotted against only one degree of freedom while the other four are kept fixed [39]. Three degrees of freedom specify the orientation of one grain relative to another, and the other two degrees of freedom specify the orientation of the boundary relative to one of the grains. In this work, Atomsk [37] is used to generate bicrystals containing 27 symmetric tilt GBs in the center of the supercell with misorientation angles between 0∘0^\circ and 90∘90^\circ as detailed in Table 1. The GB plane is the xzxz plane and is normal to the yy direction, with a tilt axis of [001][001]. By construction and due to PBCs, another GB exists at y=0y = 0, which is equivalent to y=lyy = l_y, with lyl_y being the dimension of the supercell along the yy-axis. Periodicity along the xx-axis is maintained for a plane of (ijk)(ijk) by applying the following formulae:

Planeθ\thetaΣ\SigmaPlaneθ\thetaΣ\SigmaPlaneθ\thetaΣ\Sigma
(910)12.68041a41a(830)41.112(320)67.380
(810)14.250(520)43.60329a29a(750)71.075
(710)16.26025a25a(730)46.397(430)73.740
(610)18.92537a37a(940)47.925(970)75.750
(510)22.62013a13a(210)53.1305(540)77.320
(920)25.058(950)58.109(650)79.611
(410)28.07217a17a(740)59.490(760)81.203
(720)31.891(530)61.928(870)82.372
(310)36.8705(850)64.011(980)83.267

Table 1. Grain-boundary planes studied in this work along with their misorientation angles around the [001]\left[001\right] axis, labeled θ\theta, as well as their Σ\Sigma numbers [29, 42, 43]. All symmetric tilts GBs have inherent periodicity and are CSLs [44]. However, only Σ≤49\Sigma\le49 is shown.

p=i2+j2+k2 a,(7)p = \sqrt{i^2 + j^2 + k^2}\,a, \tag*{(7)}
lx=2p⋅ceil⁡(8ap),(8)l_x = 2p \cdot\operatorname{ceil}\left(\frac{8a}{p}\right), \tag*{(8)}

where aa is the lattice constant, and pp is the structural periodicity of the GB plane [40], which is the distance between two consecutive atoms on the GB plane that are shared between the two grains. For all cases, lyl_y is arbitrarily set to lxl_x, and lzl_z is set to 8a8a. After supercell construction, rigid-body translations of one grain relative to the other are performed [25]. First, the lower grain (i.e., the grain between y=0y = 0 and y=ly/2y = l_y/2) is displaced relative to the upper grain (i.e., the grain between y=ly/2y = l_y/2 and y=lyy = l_y) in the xx-axis by distances between p/8p/8 and pp with an increment of p/8p/8 (8 configurations). Then, the lower grain is displaced by the same distances and the same increment in the yy-axis (8 configurations). For displacements along the zz-axis, only two configurations were used due to PBCs: one with no displacements, and another with a displacement of a/2a/2 [28] (2 configurations). In total, rigid-body translations give 128 different configurations for each GB plane. Finally, an atom deletion iteration was performed for each of the 128 configurations, where atoms within distances between 0.2 Å and 2 Å, in increments of 0.2 Å, are deleted (10 configurations). The aim of performing iterations of grain translations and atom deletion is to reach the true minimum energy structure of each GB plane. This method of finding the most stable GB

[]{#tbl:1} []{#eq:6} []{#eq:7} []{#eq:8} structure is commonly called the γ\gamma-surface method [41]. In total, for each GB plane, we have 1280 configurations, which are used for 0 K and finite-temperature calculations.

GB energies are calculated at 0 K and finite temperatures using the formula [28]:

EGB=E∗−NEaA,(9)E_{\mathrm{GB}} = \frac{E^{*} - N E_a}{A}, \tag*{(9)}

where E∗E^{*} is the energy of the supercell containing the GB, EaE_a is the average energy per atom in the perfect crystal (calculated as half of the cohesive energy; Ea=Ec/2E_a = E_c/2), NN is the total number of atoms in the bicrystal, and AA is the GB area calculated as A=2lxlzA = 2l_xl_z, where the factor of 2 in the GB area accounts for the two interfaces present in the system. Note that the bicrystals are guaranteed to be stoichiometric because they contain symmetric tilt GBs.

To get the GB energy at 0 K, the energy of each of the 1280 configurations is minimized with a relative energy tolerance of 10−1210^{-12}. A perfect 6×6×66 \times6 \times6 UN crystal is also minimized using the same tolerance to get the cohesive energy at 0 K. To get the GB energy at finite temperatures, each of the 1280 configurations is cooled within the NPT\mathit{NPT} ensemble from 2500 K to the target temperature for 20 ps to allow the GB to reconfigure to the minimum energy structure. Then, the system is equilibrated at the target temperature for 100 ps, where the potential energy is averaged over the final 50 ps. To get the cohesive energies at finite temperatures, a perfect 15×15×1515 \times15 \times15 UN crystal is equilibrated at the target temperature for 100 ps, where the potential energy is also averaged over the final 50 ps.

Phase-field modeling

Grain growth simulations are conducted using the phase-field module [22] of the Multiphysics Object Oriented Simulation Environment (MOOSE) framework [21]. The phase-field model of grain growth implemented in MOOSE is based on the works by Chen and Yang [45, 46] and Moelans et al. [47]. In this model, each grain is represented by a unique non-conserved order parameter, ηi\eta_i, that equals one inside the corresponding grain, and drops smoothly across the diffuse interface to become zero elsewhere in the domain.

The evolution of each grain’s order parameter, ηi\eta_i, is governed by the Allen–Cahn equation:

∂ηi∂t=−LδFδηi,(10)\frac{\partial\eta_i}{\partial t} = -L \frac{\delta F}{\delta\eta_i}, \tag*{(10)}

where LL is the order-parameter mobility, FF is the total free energy of the system, and δF/δηi\delta F/\delta\eta_i is the variational derivative of the free energy with respect to ηi\eta_i. The total free energy, FF, is the integral of the sum of the local free energy density, flocf_{\mathrm{loc}}, and the gradient energy density over the whole domain:

F=∫V(floc+κ2∑i=1N∣∇ηi∣2) dV,(11)F = \int_V \left( f_{\mathrm{loc}} + \frac{\kappa}{2} \sum_{i=1}^{N} \lvert\nabla\eta_i \rvert^2 \right) \, \mathrm{d}V, \tag*{(11)}

where κ\kappa is the gradient energy coefficient, NN is the total number of grains, and VV denotes the volume of the system. The local free energy density, flocf_{\mathrm{loc}}, is given by [47]:

floc=μ[∑i=1N(ηi44−ηi22)+32∑i=1N∑j>iNηi2ηj2+14],(12)f_{\mathrm{loc}} = \mu\left[ \sum_{i=1}^{N} \left( \frac{\eta_i^4}{4} - \frac{\eta_i^2}{2} \right) + \frac{3}{2} \sum_{i=1}^{N} \sum_{j>i}^{N} \eta_i^2 \eta_j^2 + \frac{1}{4} \right], \tag*{(12)}

where μ\mu is the free energy weight. The model parameters LL, κ\kappa, and μ\mu are related to the GB energy, γ\gamma, the diffuse GB width, ww, and the GB mobility, MM, through the following expressions [47]:

L=4M3γw,μ=6γw,κ=34γw.(13)L = \frac{4M}{3\gamma w}, \quad\mu= \frac{6\gamma}{w}, \quad\kappa= \frac{3}{4}\gamma w. \tag*{(13)}

All these expressions assume thermal equilibrium, constant molar volume, isotropic GB properties, and symmetric phase-field profiles [47]. A symmetric profile satisfies the relation ηi(x)=1−ηi(−x)\eta_i(x) = 1 - \eta_i(-x) under the assumption that the central plane of the diffuse GB interface is located at x=0x = 0, where xx is the coordinate perpendicular to the GB [47]. Relations in (13) allow the adjustment of model parameters, i.e., LL, κ\kappa, and μ\mu, so that the given GB energy and GB mobility are reproduced independently of the diffuse GB width, while letting the diffuse GB width be determined solely based on numerical and computational considerations. That is, in Moelans et al.’s grain growth model, the GB width is a numerical rather than a physical parameter.

It is worth discussing the relationship between the physical and numerical pictures of grain growth. GBs in polycrystalline materials are almost planar surfaces (or straight lines in 2D), with abrupt discontinuities at triple junctions, where high local curvature is concentrated [48, 49]. That is, in the diffuse-interface grain growth model [50], triple junctions can be regarded as high-curvature GBs, with no drag force associated with them. The solution procedure in phase-field models is based on free energy minimization [50]. By solving the Allen-Cahn equations, the system progressively reduces its free energy. Triple junctions exhibit steeper order parameter gradients, leading to higher energy penalties that drive the system to eliminate these high energy regions (especially if the dihedral angles are far from the equilibrium value of 120° [40]), ultimately promoting grain growth.

In the MOOSE framework, the Allen-Cahn equations are solved using the finite element method (FEM). In phase-field modeling of polycrystalline grain growth, assigning a unique order parameter to each grain enables accurate tracking but significantly increases computational expense. Conversely, using a single order parameter to represent multiple grains reduces computational cost but introduces artifacts, such as nonphysical grain coalescence when grains associated with the same order parameter meet. To overcome this challenge, the Grain Tracker algorithm [51] is employed. This approach permits multiple grains, referred to as features, to be associated with a single order parameter, while dynamically remapping the grain-to-order-parameter assignments to prevent nonphysical merging.

Grain growth simulations were conducted in 2D domains that span 2500 nm along the xx- and yy-axes. Initial microstructures were generated using Voronoi tessellation, yielding 500 grains in 2D, which correspond to an average initial grain size of D0=126.16D_0 = 126.16 nm. It should be mentioned that the 2D samples nearly replicate the nm-sized thin films prepared by Protasova and Sursaeva [31] to study normal grain growth in Al.

Simulations were performed over the temperature range 1500–2000 K, in 100 K increments. The initial mesh resolution was set to 120×120120 \times120. Uniform refinement of level 2 is applied to the initial mesh. The diffuse GB width, ww, was fixed at 14 nm for all simulations. Periodic boundary conditions were enforced in all spatial directions. Order parameters were implemented as constant monomial variables. Preliminary tests showed that 20 order parameters in 2D are sufficient to resolve grain morphology while maintaining computational efficiency within the Grain Tracker framework. Adaptive time stepping and mesh refinement were employed to ensure accuracy and stability. The simulations begin with an initial time step of 1 s and proceed for 10410^4 s.

At each time step, the number of grains is recorded, and the average grain size is computed. Grain sizes (or areas in 2D) are extracted using a Vector Postprocessor called the Feature Volume Vector Postprocessor which reads feature data from the Grain Tracker and outputs the area AiA_i of each grain ii at every time step (Note that in MOOSE nomenclature, the term feature here denotes a grain). The average grain area is calculated as:

Aˉ(t)=1N(t)∑i=1N(t)Ai,(14)\bar{A}(t) = \frac{1}{N(t)} \sum_{i=1}^{N(t)} A_i, \tag*{(14)}

where N(t)N(t) is the number of grains at time tt. The average grain diameter D(t)D(t) is then obtained from the relation:

D(t)=2(Aˉ(t)π)1/2.(15)D(t) = 2 \left(\frac{\bar{A}(t)}{\pi}\right)^{1/2}. \tag*{(15)}

Grain sizes/areas at each time step are also used to assess the evolution of the grain size distribution and to verify the occurrence of normal grain growth. In such growth, the normalized grain size distribution becomes time-invariant and closely follows the Hillert distribution [30]:

f(u)=(2e)d⋅d⋅u(2−u)2+dexp⁡(−2d2−u),0≤u≤2,(16)f(u) = (2e)^d \cdot\frac{d \cdot u}{(2-u)^{2+d}} \exp\left(-\frac{2d}{2-u}\right), \quad0 \leq u \leq2, \tag*{(16)}

where u=D/Dˉu = D/\bar{D} is the grain size normalized by the average grain size, and d=2d = 2 or 3 indicates the spatial dimension. The Hillert distribution has no free parameters and cannot be directly fitted to data [52]. To analyze simulation results, we instead employed a Hillert-like distribution with tunable parameters:

f(u)=Cumexp⁡(−bun),0≤u≤2.25,(17)f(u) = C u^m \exp(-b u^n), \quad0 \leq u \leq2.25, \tag*{(17)}

where CC, bb, mm, and nn are fitting constants. This function retains the essential qualitative features of the Hillert distribution, e.g., its positive skewness, while offering flexibility for empirical fitting. The upper limit of our distribution has been increased to u=2.25u = 2.25 based on the observation that a distribution consistent with experimental measurements usually has 99.9% of the grains below u=2.2u = 2.2 [53].

In the following section, we present an uncertainty analysis to evaluate the impact of uncertainties in the GB mobility prefactor, GB mobility activation energy, and GB energy on the final grain structure. In contrast, performing a similar analysis for uncertainties in the initial grain size distribution is more complex, as this distribution represents a topological characteristic of the simulation rather than a simple numerical input. Specifically, the probability distribution of the initial grain sizes cannot be readily quantified. To approximate the influence of this uncertainty, we analyze grain growth across ten different initial microstructures generated using ten distinct random seeds. The reported grain growth is then taken as the average over these simulations.

Uncertainty quantification and sensitivity analysis

Understanding how uncertainties in input parameters influence grain growth predictions in phase-field models is essential for assessing model robustness and identifying dominant factors. To this end, we implement a surrogate-assisted framework that combines uncertainty propagation, dimensionality reduction, Gaussian process regression, and global sensitivity analysis. The uncertainty quantification and sensitivity analysis calculations are conducted using in-house Python scripts. The grain growth observations are treated as noise-free. Hence, uncertainty is attributed exclusively to model parameters. We focus on three key uncertain inputs: the mobility prefactor M0M_0, the activation energy QMQ_M, and the GB energy γ\gamma.

The mobility MM is estimated from grain growth experimental data [23] via regression (Section 3.2), yielding maximum likelihood estimates and a covariance matrix for M0M_0 and QMQ_M. The prefactor M0=ebM_0 = e^b is modeled as log-normally distributed, where b∼N(μ=−33.82,σ2=0.822)b \sim\mathcal{N}(\mu= -33.82, \sigma^2 = 0.82^2). The activation energy QMQ_M follows a normal distribution N(μ=0.89 eV,σ2=0.112 eV2)\mathcal{N}(\mu= 0.89\ \mathrm{eV}, \sigma^2 = 0.11^2\ \mathrm{eV}^2) (see Section 3.2). The GB energy, γ\gamma, is modeled as a normal distribution. Its mean is obtained from a correlation fit to MD data of 27 GB energies ((19)), while the standard deviation is set to 29.6% of the mean, based on a statistical analysis of the same dataset. All uncertain inputs are sampled from their prescribed distributions using inverse-CDF (PPF) transforms with an enforced ±3σ\pm3\sigma cutoff in standard-normal space. In addition, the activation energy QMQ_M and grain-boundary energy γ\gamma are modeled as truncated normal distributions constrained to positive values only.

Our quantity of interest (QoI) is the average grain size D(t)D(t). Because D(t)D(t) evolves over time, the QoI is inherently multivariate and can be represented as a vector-valued function. Each element in this vector corresponds to a time-resolved scalar output, requiring specialized methods for uncertainty quantification and sensitivity analysis that account for temporal dynamics. For this purpose, we utilize a methodology outlined in detail in [54, 55, 56, 57]. Here, we only give a brief overview.

To propagate uncertainty through the phase-field model, we generate 330 parameter samples using Latin hypercube sampling (LHS) [58] with a maximin criterion and 500 optimization iterations, ensuring good coverage of the input space (see Figure 1). For each sample, we perform the MOOSE-based phase-field simulations as described in Section 2.3. Due to the high computational cost of these simulations, direct sensitivity analysis on the full time-dependent model outputs is infeasible. Accordingly, the grain size time series are first preprocessed prior to surrogate construction: The data are log-transformed as ln⁡(D)\ln(D) so that early-time variations do not appear negligible compared to late-time variations. All simulation outputs are mapped onto a common temporal grid to accommodate variations in adaptive time-stepping. Missing values at specified grid points are forward-filled using the last available observation. To reduce temporal redundancy and computational cost, the time series are downsampled by retaining every 20th time step after skipping the initial 5 transient steps. The analysis is truncated at 5000 s to maintain sufficient grain count for reliable statistics.

Input parameter samples and pairwise correlations

Figure 1. Input parameter samples and pairwise correlations used in the UQ analysis. Samples are drawn for three uncertain quantities: the natural logarithm of the GB mobility prefactor ln⁡(M0)\ln(M_0) (where M0M_0 is in m4/J⋅s\mathrm{m}^4/\mathrm{J}\cdot\mathrm{s}), the mobility activation energy QMQ_M (eV), and the GB energy γ\gamma (J/m2\mathrm{J}/\mathrm{m}^2). Diagonal panels show their marginal distributions, while off-diagonal panels show correlations among parameters.

To reduce the dimensionality of the resulting time-dependent QoI, we then apply principal component analysis (PCA). Prior to PCA, the log-transformed grain size data are standardized independently at each time step to zero mean and unit variance across runs. PCA transforms the correlated time series into a set of uncorrelated principal components (PCs) that preserve 98% of the total variance, which are then modeled with Gaussian process surrogates.

M0M_0 is log-transformed to ln⁡(M0)\ln(M_0) to account for its log-normal distribution and reduce skewness, while QMQ_M and γ\gamma remain in their original scale. All three inputs are then standardized to zero mean and unit variance. Independent single-output Gaussian process regression models are trained for each of the PCs using the GPflow library [59, 60]. A Matérn-5/2 kernel is employed to provide twice-differentiable predictive mean functions.

The GP model decomposes the observed PC scores into a smooth underlying function and observational noise:

y=f(x)+ϵ,ϵ∼N(0,σn2),(18)y = f(\mathbf{x}) + \epsilon,\quad\epsilon\sim\mathcal{N}(0,\sigma_n^2), \tag*{(18)}

where f(x)f(\mathbf{x}) represents the deterministic relationship between input parameters and PC scores, and σn2\sigma_n^2 is the noise variance. Since the phase-field simulations are deterministic, σn2\sigma_n^2 is expected to be small. It is therefore regularized by a Gamma(2, 200) prior, which places a weakly informative constraint with mean E[σn2]=2/200=0.01\mathbb{E}[\sigma_n^2] = 2/200 = 0.01 in standardized PC space, preventing the optimizer from inflating σn2\sigma_n^2 to absorb signal. Model hyperparameters are optimized using the Adam optimizer with a learning rate of 0.001, employing early stopping with a patience of 200 iterations and a minimum improvement threshold of 10−410^{-4} to prevent overfitting.

The GP surrogate accuracy is assessed using in-sample R2R^2 and predictive Q2Q^2, computed under repeated five-fold cross-validation with five repeats (25 train-test splits total). The trained surrogates predict PC scores for new parameter samples, which are then inverted via PCA to reconstruct full time-dependent grain size profiles. The Python library scikit-learn [61] is used in this study for dimensionality reduction via PCA, standardization of input parameters and PC scores, and rigorous model validation through repeated cross-validation.

To quantify the influence of each uncertain input over time, we perform a variance-based global sensitivity analysis using Sobol indices [62, 63, 64]. First-order (S1S_1) and total-effect (StS_t) indices are computed to assess both individual and interactive contributions of parameters to the variance of the QoI. These indices are calculated at each time step, enabling time-resolved sensitivity analysis. The Saltelli sampling scheme, implemented via the SALib package [65, 66], is employed to estimate first-order and total-order Sobol indices with a base sample size of N=213=8,192N = 2^{13} = 8{,}192, requiring N(d+2)=40,960N(d + 2) = 40{,}960 model evaluations in the three-dimensional (d=3d = 3) input space. The GP surrogate replaces the computationally intensive phase-field model, allowing efficient and accurate estimation of Sobol indices across the time domain. Point estimates of the indices are obtained from the GP predictive mean, with confidence intervals computed using the bootstrap resampling method implemented in SALib.

This surrogate-assisted methodology, summarized in Figure 2, enables efficient uncertainty quantification and sensitivity analysis for multivariate, time-resolved outputs.

Computational methodology flowchart for time-dependent Sobol indices

Figure 2. Computational methodology for time-dependent Sobol indices.

Results

Grain-boundary energy

Representative minimized bicrystal GBs from the Tseplyaev and Kocyeski potentials are shown in Figure 3. After 0 K minimization of the bicrystals using the Kocyeski potential, a void space is still observed between the two grains. That is, the GB doesn’t “close” after minimization (Figure 3b). This is due to the inability of the Kocyeski potential to simulate metallic U, which leads to mutual repulsion among U atoms. For the Tseplyaev potential, the GB closes after 0 K minimization as expected (Figure 3a), because it was demonstrated that the Tseplyaev potential can simulate metallic U [4] and expresses no anomalous effects related to U-U repulsion. However, the Kocevski potential is still utilized to calculate GB energies at 0 K for completeness.

Top view along the z-axis of the (310) GB plane after 0 K minimization using the Tseplyaev potential

(a)

Top view along the z-axis of the (310) GB plane after 0 K minimization using the Kocevski potential

(b)

Figure 3. (Color online) Top view along the zz-axis of the same configuration of the (310) GB plane after 0 K minimization using (a) the Tseplyaev potential, and (b) the Kocevski potential. U atoms are colored in red, and N atoms are colored in blue.

The GB energy as a function of misorientation angle at 0 K and the GB energy as a function of temperature are shown in Figure 4. From fig:4a, the Kocevski potential consistently predicts smaller GB energies than those predicted by the Tseplyaev potential at 0 K. This stems from the fact that U-U repulsion shifts pair distances to the tail of the potential energy versus distance curve, where the interaction energy is usually small. Because a large number of the GB planes with misorientation angles within the range of 10∘10^\circ–30∘30^\circ form coincidence site lattices (CSLs), with Σ\Sigma values ranging from 13 to 41 (Table 1), they display very close GB energies nearly independent of the misorientation angle. The situation is different for GB planes with misorientation angles in the range of 70∘70^\circ–90∘90^\circ, which do not form CSLs and show the trend expected for low-angle GBs [40].

Variation of grain boundary energy with misorientation angle and temperature

Figure 4. (a) Variation of the GB energy with misorientation angle at 0 K, as predicted by both potentials. The DFT values are from [29]. The dashed lines correspond to an average of the GB energy over all misorientation angles. (b) Variation of the average GB energy with temperature as predicted by the Tseplyaev potential.

The (310) and (210) GB planes, with misorientation angles of 36.87∘36.87^\circ and 53.13∘53.13^\circ, respectively, show remarkably low energies. These planes have the smallest Σ\Sigma value possible for a tilt GB, i.e., Σ=5\Sigma= 5. For GBs with low Σ\Sigma numbers, a large fraction of the atoms in the GB plane are positioned exactly as they would be in a perfect lattice, which leads to a smaller GB energy [39]. Note that in fig:4a, the GB energy predicted by the Tseplyaev potential is close to the DFT values, whereas that predicted by the Kocevski potential is largely underestimated. It should be mentioned that we calculated the energy of a few symmetric tilt GBs at 0 K using much larger supercells and found the GB energy to be independent of the supercell size.

Because the Kocevski potential is not able to properly simulate GBs, the finite-temperature calculation of the GB energies was performed using only the Tseplyaev potential. The variation of the GB energy with misorientation angle predicted at finite temperatures (not shown) is nearly identical to that at 0 K (fig:4a). An average GB energy over all of the misorientation angles at each temperature is calculated and plotted in fig:4b. The Tseplyaev potential also predicts a nearly temperature-independent GB energy up to about 1000 K and then an increase in GB energy at higher temperatures. The data points in fig:4b have been fitted to a polynomial function:

γ=1.382+3.279×10−6T+5.748×10−18T5 (J/m2)(19)\gamma= 1.382 + 3.279 \times10^{-6} T + 5.748 \times10^{-18} T^{5}\ \left(\mathrm{J/m}^{2}\right) \tag*{(19)}

with R2=0.983R^2 = 0.983. Because of the large power of TT in (19), the fitted correlation should be used with caution outside the fitted range, i.e., at T>2000T > 2000 K. The standard deviation of the averaged 27 GB energies is found to be about 30% at all temperatures. A GB energy that increases with temperature has been observed for U3_3Si2_2 by Beeler et al. [28], and is often correlated with increased disorder in the GB region [67]. This disorder likely stems from the enhanced bulk diffusivity of the nitrogen sublattice, which remained zero until near 2000 K and then began to increase, as observed in our previous work [7].

Grain-boundary mobility

GB mobility, MM, is a fundamental parameter governing grain growth kinetics in nuclear fuel materials. Its determination requires careful experimental measurement, theoretical analysis, and/or modeling. In the literature, only one experimental study has investigated grain growth in actinide nitride fuels. Ronchi and Sari [23] conducted measurements on (U,Pu)N pellets subjected to annealing at 1400–2000 K for 500 hours under thermal gradients of approximately 1000 K/cm. The pellets had initial grain size D0=6D_0 = 6 µm and porosity of approximately 15 vol.%, with 55% of this porosity located at grain boundaries. Their measurements followed the empirical growth law:

D3−D03=K(T)t,(20)D^3 - D_0^3 = K(T)t, \tag*{(20)}

where the rate constant K(T)K(T) exhibits Arrhenius temperature dependence, as shown in Figure 5. The cubic growth exponent n=3n = 3 deviates from the quadratic behavior n=2n = 2 expected for drag-free curvature-driven grain growth, indicating the presence of a resistive mechanism commonly attributed to pore drag in porous ceramics.

Grain growth Arrhenius plot for (U,Pu)N pellets

Figure 5. Grain growth Arrhenius plot for (U,Pu)N pellets heated in a thermal gradient of 1000 K/cm for an annealing time of 500 hours. The data is taken from Ronchi and Sari [23]. The data were fitted to the equation D3−D03=KtD^3 - D_0^3 = Kt, with QK=1.13±0.11Q_K = 1.13 \pm0.11 eV, and K0=3.856×10−19K_0 = 3.856 \times10^{-19} m3^3/s.

We are confronted with two challenges in extracting intrinsic GB mobility from these measurements. First, the grain growth was observed under a temperature gradient rather than isothermal conditions. Second, the grain size exponent is n=3n = 3 instead of the ideal n=2n = 2 case expected for drag-free growth. Tonks et al. [13] and Bai et al. [18] showed that in UO2_2, temperature gradients have minimal impact on the overall grain growth behavior when compared to the curvature driving force. Indeed, temperature gradients do affect temperature-dependent GB mobility, causing GBs to migrate quickly in hotter areas and slowly in cooler areas. As a result, temperature gradients influence local grain growth but do not change the average grain growth behavior. Given that UN exhibits higher thermal conductivity than UO2_2, its operational temperature gradient is reduced to 1/51/5–1/21/2 that of UO2_2 [23, 68], further decreasing the significance of the temperature gradient as a driving force for grain growth in UN. Therefore, the measurements from Ronchi and Sari are assumed to be approximately indicative of isothermal grain growth.

For the second challenge, we present a methodology to extract the drag-free GB mobility, MM, from the cubic grain growth kinetics. The procedure consists of three steps: (i)(i) determination of the effective mobility from experimental kinetics, (ii)(ii) construction of a mechanistic pore-drag model with partial coupling, and (iii)(iii) global regression to extract intrinsic mobility parameters.

Effective mobility from experimental kinetics

The temperature-dependent growth constant in (20) follows an Arrhenius relation:

K(T)=K0exp⁡(−QKkBT).(21)K(T) = K_0 \exp\left(-\frac{Q_K}{k_B T}\right). \tag*{(21)}

Taking the logarithm yields a linear form:

ln⁡K=ln⁡K0−QKkB1T,(22)\ln K = \ln K_0 - \frac{Q_K}{k_B}\frac{1}{T}, \tag*{(22)}

which is fitted by linear regression in 1/T1/T to obtain the activation energy QKQ_K and pre-exponential factor K0K_0, along with their covariance matrix. From the experimental data of Ronchi and Sari, we extract QK=1.13±0.11Q_K = 1.13 \pm0.11 eV and K0=3.856×10−19 m3/sK_0 = 3.856 \times10^{-19}\ \mathrm{m^3/s}.

The cubic exponent n=3n = 3 suggests the presence of a resistive force, likely pore drag. Powers and Glaeser [16] proposed that such non-parabolic kinetics can be rationalized by assuming the growth constant depends on the instantaneous grain size. Specifically, they introduced an effective mobility Meff(T)M_{\mathrm{eff}}(T) such that:

D3−D03=3αMeff(T)γ(T)D(T)t,(23)D^3 - D_0^3 = 3\alpha M_{\mathrm{eff}}(T)\gamma(T)D(T)t, \tag*{(23)}

where α≈1\alpha\approx1 is a geometric constant for 3D grains [19] and γ(T)\gamma(T) is the GB energy. Equating (20) and (23) and rearranging yields the effective mobility:

Meff(T)=K(T)3αγ(T)D(T).(24)M_{\mathrm{eff}}(T) = \frac{K(T)}{3\alpha\gamma(T)D(T)}. \tag*{(24)}

Here, γ(T)\gamma(T) is obtained independently from MD simulations (Section 3.1), and D(T)D(T) is reconstructed from the experimental grain growth data at each temperature by solving D=(D03+K(T)t)1/3D = \left(D_0^3 + K(T)t\right)^{1/3}.

Mechanistic pore-drag model

The effective mobility MeffM_{\mathrm{eff}} differs from the intrinsic (drag-free) mobility, MM, due to the resistive force exerted by pores on migrating GBs. Following the formulation of Tonks et al. [19], which builds on the classical framework of Powers and Glaeser [16], the mobility reduction is expressed as:

Meff(T)=M(T)1+Na(T)M(T)Mp(T)(25)M_{\mathrm{eff}}(T) = \frac{M(T)}{1 + \frac{N_a(T)M(T)}{M_p(T)}} \tag*{(25)}

where M(T)M(T) is the intrinsic GB mobility, Na(T)N_a(T) is the areal number density of pores attached to GBs and participating in drag, and Mp(T)M_p(T) is the pore mobility in units of m2/(J⋅s)\mathrm{m}^{2}/(\mathrm{J}\cdot\mathrm{s}), with is different from the unit of GB mobility (i.e., m4/(J⋅s)\mathrm{m}^{4}/(\mathrm{J}\cdot\mathrm{s})).

To quantify the degree of mobility reduction, we define the dimensionless drag parameter:

λ(T)=Na(T)M(T)Mp(T)(26)\lambda(T) = \frac{N_a(T)M(T)}{M_p(T)} \tag*{(26)}

which represents the ratio of the GB transport capacity to the pore transport capacity. When λ≪1\lambda\ll1, pores are highly mobile relative to GBs and drag effects are negligible. When λ≫1\lambda\gg1, pores are effectively immobile and strongly drag (or possibly pin) GBs.

The mobility reduction factor is then defined as:

s(T)≡Meff(T)M(T)=11+λ(T).(27)s(T) \equiv\frac{M_{\mathrm{eff}}(T)}{M(T)} = \frac{1}{1+\lambda(T)}. \tag*{(27)}

This factor quantifies the fractional reduction in GB mobility due to pore drag, with s=1s = 1 indicating no drag (drag-free conditions) and s→0s \to0 indicating strong drag and possibly pinning. s(T)s(T) is not assumed a priori but is computed mechanistically from the underlying microstructural parameters: MM, MpM_p, and NaN_a.

Areal pore density with partial coupling

In the intermediate-temperature regime (1400–2000 K), Ronchi and Sari reported three particularly relevant observations on microstructural evolution: (i) pore number density reaches an approximate plateau at about n≈1.35×1014 m−3n \approx1.35 \times10^{14}\ \mathrm{m}^{-3}, (ii) the characteristic pore diameter scales nearly linearly with grain size such that Dp/D≈0.54D_p/D \approx0.54, and (iii) micrographic evidence shows that some pores are left behind by advancing GBs rather than remaining continuously attached. These observations suggest that pore-GB coupling is partial rather than complete.

To account for partial coupling, we introduce an effective coupling fraction ϕ∈[0,1]\phi\in[0, 1] that represents the fraction of pores that actively participate in drag:

Na(T)=ϕNp(T),(28)N_a(T) = \phi N_p(T), \tag*{(28)}

where Np(T)N_p(T) is the total pore number density per GB area (wether attached to GBs or not). The parameter ϕ\phi is a lumped effective quantity accounting for two physical effects: (i) not all pores in the bulk reside on GBs (some are intragranular), and (ii) of those pores that do contact GBs, only a fraction remain attached and migrate with the boundary at any given time (the rest are left behind).

For equiaxed, nearly spherical grains of size DD, the GB surface area per unit volume is:

Sv=12πD2πD3/6=3D,(29)S_v = \frac{1}{2}\frac{\pi D^2}{\pi D^3/6} = \frac{3}{D}, \tag*{(29)}

where the factor of 1/21/2 accounts for each GB being shared by two grains. If nn is the volumetric pore number density, then the total areal pore number density is:

Np(T)=nSv=nD(T)3.(30)N_p(T) = \frac{n}{S_v} = \frac{nD(T)}{3}. \tag*{(30)}

Pore mobility

For spherical pores migrating via surface diffusion, the pore mobility is given by [16]:

Mp(T)=Ds(T)δsΩkBTπrp4(T),(31)M_p(T) = \frac{D_s(T)\delta_s\Omega}{k_{\mathrm{B}}T\pi r_p^4(T)}, \tag*{(31)}

where Ds(T)D_s(T) is the surface diffusivity, δs=0.5\delta_s = 0.5 nm [19] is the effective thickness of the surface diffusion layer, Ω=a3/8\Omega= a^3/8 is the atomic volume for UN with NaCl structure (lattice parameter a=4.89a = 4.89 Å), and rp(T)r_p(T) is the pore radius. (31) assumes that pores remain spherical during migration.

Direct measurements or atomistic calculations of surface diffusivity in UN are not available. As an approximation, we adopt an Arrhenius fit to the recommended order-of-magnitude estimate for UO2_2 from Muntaha et al. [69], which gives Ds∼10−9D_s \sim10^{-9} m2^2/s at 2000 K and Ds∼10−17D_s \sim10^{-17} m2^2/s at 1000 K. This introduces substantial uncertainty in Mp(T)M_p(T), potentially spanning an order of magnitude, which propagates into the pore drag model. Therefore, the extracted intrinsic mobility parameters should be interpreted as order-of-magnitude estimates.

Based on the observed scaling relation Dp/D≈0.54D_p/D \approx0.54 [23], we model the pore radius as:

rp(T)=Dp2≈0.27D(T).(32)r_p(T) = \frac{D_p}{2} \approx0.27D(T). \tag*{(32)}

Global regression for intrinsic mobility

The intrinsic GB mobility follows an Arrhenius relation:

M(T)=M0exp⁡(−QMkBT).(33)M(T) = M_0 \exp\left(-\frac{Q_M}{k_{\mathrm{B}}T}\right). \tag*{(33)}

Substituting Eqs. (30) to (33) into the drag relation Eq. (25) gives the forward model for the effective mobility:

M^eff(T;M0,QM,ϕ)=M0exp⁡(−QM/(kBT))1+ϕnD(T)M0exp⁡(−QM/(kBT))3Mp(T).(34)\widehat{M}_{\mathrm{eff}}(T; M_0,Q_M,\phi) = \frac{M_0\exp\left(-Q_M/(k_{\mathrm{B}}T)\right)} {1+\dfrac{\phi nD(T)M_0\exp\left(-Q_M/(k_{\mathrm{B}}T)\right)}{3M_p(T)}}. \tag*{(34)}

where all temperature-dependent quantities (D(T)D(T), Mp(T)M_p(T) via Ds(T)D_s(T) and rp(T)r_p(T)) are evaluated at the experimental temperatures.

The three unknown parameters (M0,QM,ϕ)(M_0, Q_M, \phi) are obtained by minimizing the logarithmic least-squares objective:

min⁡M0,QM,ϕ∑i[ln⁡M^eff(Ti;M0,QM,ϕ)−ln⁡Meff(Ti)]2(35)\min_{M_0,Q_M,\phi} \sum_i \left[\ln\hat{M}_{\mathrm{eff}}(T_i; M_0, Q_M, \phi) - \ln M_{\mathrm{eff}}(T_i)\right]^2 \tag*{(35)}

subject to the physical constraints:

M0>0,QM>0,0≤ϕ≤1.(36)M_0 > 0,\qquad Q_M > 0,\qquad0 \le\phi\le1. \tag*{(36)}

The logarithmic objective function ensures approximately uniform weighting in relative error across the temperature range, avoiding overemphasis of high-temperature points where mobilities are largest.

The optimization is performed using the trust-region reflective algorithm [70] with initial guess obtained from the effective mobility Arrhenius fit (ln⁡M0,initial=ln⁡M0,eff,QM,initial=Qeff)(\ln M_{0,\mathrm{initial}} = \ln M_{0,\mathrm{eff}}, Q_{M,\mathrm{initial}} = Q_{\mathrm{eff}}) and a moderate initial coupling fraction (ϕinitial=0.3)(\phi_{\mathrm{initial}} = 0.3). After fitting, the dimensionless drag parameter, λ(T)\lambda(T), and mobility reduction factor, s(T)s(T), at each experimental temperature are computed from the fitted parameters (M0,QM,ϕ)(M_0, Q_M, \phi).

The final relation linking the experimentally measured growth constant, K(T)K(T), to the intrinsic mobility, M(T)M(T), is therefore:

K(T)=3αγ(T)D(T)s(T)M(T)=3αγ(T)D(T)M(T)1+λ(T),(37)K(T) = 3\alpha\gamma(T) D(T) s(T) M(T) = 3\alpha\gamma(T) D(T) \frac{M(T)}{1+\lambda(T)}, \tag*{(37)}

which explicitly shows how the phenomenological growth constant depends on both the intrinsic mobility and the mechanistically-computed drag effects.

Fitted parameters and diagnostics

Application of our methodology to the Ronchi and Sari data yields the intrinsic GB mobility parameters shown in Figure 6. Global nonlinear regression of the partial-coupling pore drag model ((34)) to the temperature-dependent effective mobility yields:

Temperature dependence of grain boundary mobility in uranium mononitride

Figure 6. Temperature dependence of grain boundary mobility in uranium mononitride: drag-free intrinsic mobility MM (squares), kinetic effective mobility MeffM_{\mathrm{eff}} from experimental data (circles), and model-predicted effective mobility M^eff\widehat{M}_{\mathrm{eff}} (diamonds). Agreement between MeffM_{\mathrm{eff}} and M^eff\widehat{M}_{\mathrm{eff}} validates the extracted parameters.

QM=0.87 eV,M0=1.75×10−15 m4/(J⋅s),ϕ=1.00.(38)Q_M = 0.87\ \mathrm{eV},\qquad M_0 = 1.75 \times10^{-15}\ \mathrm{m}^4/(\mathrm{J}\cdot\mathrm{s}),\qquad\phi= 1.00. \tag*{(38)}

These parameters are nearly identical to those obtained from the effective mobility Arrhenius fit (Qeff=0.89 eV,M0,eff=2.05×10−15 m4/(J⋅s))(Q_{\mathrm{eff}} = 0.89\ \mathrm{eV}, M_{0,\mathrm{eff}} = 2.05 \times10^{-15}\ \mathrm{m}^4/(\mathrm{J}\cdot\mathrm{s})), differing by less than 3% in activation energy and 15% in prefactor.

The fitted coupling parameter converged to the upper bound ϕ=1.00\phi= 1.00, corresponding to full coupling. Table 2 shows the self-consistent drag diagnostics computed from the fitted parameters. The dimensionless drag parameter ranges from λ≈0.006\lambda\approx0.006 at 1980 K to λ≈0.074\lambda\approx0.074 at 1427 K, yielding reduction factors s≈0.93s \approx0.93–0.990.99. This indicates that pore drag reduces GB mobility by at most 7% relative to the intrinsic value.

TT (K)DD (μ\mum)rpr_{\mathrm{p}} (μ\mum)λ\lambdass
198010.22.760.0060.994
17458.302.240.0110.989
15537.351.990.0350.966
15417.191.940.0350.966
14276.471.750.0740.931

Table 2. Self-consistent pore drag diagnostics for uranium mononitride grain growth.

Given the order-of-magnitude uncertainties in the surface diffusivity estimate (drawn from UO2_2 data), the spherical pore approximation, and the limited experimental dataset (five temperatures at a single annealing time), the fitted reduction factors s≈0.93s \approx0.93–0.990.99 are statistically indistinguishable from unity. For this reason, in the following analysis we assume the weak-drag limit and adopt the effective mobility as the intrinsic mobility:

M(T)=Meff(T)=2.05×10−15exp⁡(−0.89 eVkBT) m4/(J⋅s).(39)M(T) = M_{\mathrm{eff}}(T) = 2.05 \times10^{-15} \exp\left(\frac{-0.89\ \mathrm{eV}}{k_B T}\right)\ \mathrm{m}^4/(\mathrm{J}\cdot\mathrm{s}). \tag*{(39)}

This choice is justified by the near-unity reduction factors from the drag model and is further validated by the following exponent analysis.

We tested whether the experimental data can distinguish between cubic (n=3n = 3) and parabolic (n=2n = 2) grain growth kinetics. Fitting both models yields R2=0.970R^2 = 0.970 (cubic) and R2=0.961R^2 = 0.961 (parabolic), with ΔR2=0.009<0.01\Delta R^2 = 0.009 < 0.01. The statistical equivalence of both kinetic models confirms that the experimental kinetics are indistinguishable from ideal parabolic growth. We therefore conclude that pore drag effects are negligible in the specific samples and microstructural conditions examined by Ronchi and Sari, and the effective mobility measured from their experiments directly represents the intrinsic GB mobility, as given in (39).

Phase-field modeling

Representative grain structures at the beginning of the simulation and after 10410^4 s of growth at 1500 K are shown in Figure 7. These images clearly illustrate the substantial grain coarsening that occurs during the simulation. The corresponding time evolution of (D2−D02)(D^2-D_0^2) for all initial microstructures at 1500 K is presented in fig:8a. It can be seen that the (D2−D02)(D^2-D_0^2) curves are linear for all initial microstructures, confirming that normal grain growth is observed. To further verify this observation, we plotted the normalized grain size distributions for 2000 K between time steps 100–500 (corresponding to about 300–1900 s) in fig:8b. As expected, all normalized grain size distributions follow the Hillert-like distribution. Independent of the initial distribution (e.g., the green histogram in fig:8b), the grain size distribution quickly shifts to the positively skewed Hillert-like distribution typical of normal grain growth. The fitted parameters for the Hillert-like distribution in (17) at 2000 K averaged over all initial microstructures are shown in Table 3. Similar trends have been observed for all initial microstructures at all temperatures.

Microstructural evolution at 1500 K during grain growth: initial fine-grained and coarsened structures

Figure 7. Microstructural evolution at 1500 K during grain growth. (a) The initial fine-grained structure at t=0t = 0 s and (b) the coarsened structure after 10410^4 s.

ParameterValue
CC0.1281±0.01810.1281 \pm0.0181
mm1.3682±0.29541.3682 \pm0.2954
nn0.3315±0.12210.3315 \pm0.1221
bb4.0175±0.51724.0175 \pm0.5172

Table 3. Fitted parameters for the Hillert-like distribution, i.e., (17), at 2000 K averaged over all initial microstructures.

Simulation results for grain growth kinetics and normalized grain size distributions

Figure 8. (a) Simulation results for the time evolution of (D2−D02)(D^2 - D_0^2) at 1500 K using 10 different initial microstructures. (b) Grain size evolution at 2000 K between time steps 100–500 (corresponding to about 300–1900 s) represented by normalized grain size distributions (gray points) fitted to a Hillert-like distribution (dark line). The initial grain size distribution (green histogram) is also shown for comparison.

To quantify the sensitivity of the predicted kinetics to the initial microstructure, we define the coefficient of variation as:

CV⁡(t)=3σ(t)μ(t),(40)\operatorname{CV}(t) = \frac{3\sigma(t)}{\mu(t)}, \tag*{(40)}

where σ(t)\sigma(t) is the sample standard deviation and μ(t)\mu(t) is the mean grain size across all ten independent simulations at time tt. The 3σ3\sigma confidence interval normalized by the mean captures approximately 99.7% of the distribution assuming normality.

Figure 9 shows the evolution of the coefficient of variation as a function of time for all temperatures. The CV exhibits a consistent trend across all temperatures: starting from near zero at t=0t = 0, CV⁡(t)\operatorname{CV}(t) increases as grain growth proceeds, reflecting the early-stage divergence among systems with different initial grain size distributions. As coarsening continues, CV⁡(t)\operatorname{CV}(t) gradually approaches an asymptotic plateau, signaling the achievement of self-similarity in the grain-size distribution.

Time evolution of the coefficient of variation at all simulated temperatures

Figure 9. Time evolution of the coefficient of variation at all simulated temperatures.

To quantify this behavior, we fit the CV evolution to an exponential saturation model [7]:

CV⁡(t)=CV⁡0(1−e−βt),(41)\operatorname{CV}(t) = \operatorname{CV}_0 \left(1 - e^{-\beta t}\right), \tag*{(41)}

where CV⁡0\operatorname{CV}_0 is the asymptotic coefficient of variation and β\beta is the rate constant characterizing the approach to steady state. The fitted parameters reveal a systematic temperature dependence, summarized in Table 4. The asymptotic CV increases monotonically with temperature, from CV⁡0≈0.053\operatorname{CV}_0 \approx0.053 at 1500 K to CV⁡0≈0.120\operatorname{CV}_0 \approx0.120 at 2000 K, indicating that higher temperatures produce broader grain size distributions at steady state. Simultaneously, the rate constant β\beta increases from 2.98×10−4 s−12.98 \times10^{-4}\ \mathrm{s}^{-1} at 1500 K to 1.14×10−3 s−11.14 \times10^{-3}\ \mathrm{s}^{-1} at 2000 K, demonstrating a faster approach to the steady-state distribution at elevated temperatures. strating that higher temperatures accelerate the approach to self-similarity. The characteristic time to reach steady state, τ=1/β\tau= 1/\beta, decreases from approximately 3360 s at 1500 K to 875 s at 2000 K.

Temperature (K)CV0\mathrm{CV}_0β\beta (s−1^{-1})
15000.05332.98×10−42.98 \times10^{-4}
16000.08144.15×10−44.15 \times10^{-4}
17000.09635.53×10−45.53 \times10^{-4}
18000.10597.14×10−47.14 \times10^{-4}
19000.10799.04×10−49.04 \times10^{-4}
20000.11991.14×10−31.14 \times10^{-3}

Table 4. Fitted parameters for the coefficient of variation evolution.

This rise and subsequent saturation of CV has been reported in previous studies, such as the work by Breithaupt et al. [53], who found that the CV saturates at approximately 0.40 for all initial conditions considered. While our CV quantifies variability across simulations rather than within a single microstructure as in Breithaupt et al., the qualitative behavior, i.e., monotonic increase followed by exponential saturation, demonstrates that both inter-simulation and intra-microstructure heterogeneity exhibit analogous evolution toward self-similarity.

In summary, this analysis demonstrates that while the influence of the initial grain size distribution persists, it becomes bounded at long times as the system approaches self-similarity. The temperature-dependent asymptotic CV values and rate constants reveal that higher temperatures promote both greater steady-state heterogeneity and faster kinetics toward the self-similar regime.

Uncertainty quantification and sensitivity analysis

Grain size distribution and analysis of extremes

As shown in fig:10b, the final grain size distribution at t=5000t = 5000 s is approximately log-normal. To understand why, note that:

ln⁡D=const⁡+12ln⁡M0+12ln⁡γ−QM2kBT.(42)\ln D = \operatorname{const} + \frac{1}{2}\ln M_0 + \frac{1}{2}\ln\gamma- \frac{Q_M}{2k_B T}. \tag*{(42)}

The dominant contributions to ln⁡D\ln D are Gaussian: ln⁡M0\ln M_0 is normally distributed by construction, and QMQ_M follows a weakly truncated normal distribution. The remaining term, 12ln⁡γ\frac{1}{2}\ln\gamma, is assessed using the delta method [71, 72]. We expand ln⁡γ\ln\gamma about μγ\mu_\gamma,

12ln⁡γ=12(ln⁡μγ+γ−μγμγ−(γ−μγ)22μγ2+⋯ )(43)\frac{1}{2}\ln\gamma= \frac{1}{2}\left(\ln\mu_\gamma+ \frac{\gamma- \mu_\gamma}{\mu_\gamma} - \frac{(\gamma- \mu_\gamma)^2}{2\mu_\gamma^2} + \cdots\right) \tag*{(43)}

The linear term is a normal random variable. The quadratic term has expected magnitude scaling as σγ2/μγ2≈0.088\sigma_\gamma^2/\mu_\gamma^2 \approx0.088, and after the prefactor of 1/21/2 in ln⁡D\ln D, its net contribution is approximately 4–5%. The non-Gaussian distortion from ln⁡γ\ln\gamma is therefore small relative to the dominant Gaussian terms from ln⁡M0\ln M_0 and QMQ_M, so ln⁡D\ln D is approximately normal and DD is approximately log-normal, consistent with the right-skewed histogram observed in fig:10b.

Grain growth trajectories and distribution of final grain sizes

Figure 10. (a) Grain growth trajectories: gray lines show all 330 simulations, the shaded band represents the log-normal σ\sigma interval, and the black line shows the geometric mean. Red lines indicate the two largest final grain sizes, while blue lines indicate the two smallest. (b) Distribution of final grain sizes at t=5000t = 5000 s. The histogram shows right skewness characteristic of log-normal distributions.

The grain size distribution exhibits two orders of magnitude spread (Figs. 10a and 10b). As shown in Fig. 11a, the two largest final grain sizes (2821 nm and 1995 nm) result from high M0M_0 and low QMQ_M: sample 197 has M0=2.08×10−14M_0 = 2.08 \times10^{-14} m4^4/(J⋅\cdots) and QM=0.645Q_M = 0.645 eV, while sample 218 has M0=9.17×10−15M_0 = 9.17 \times10^{-15} m4^4/(J⋅\cdots) and QM=0.748Q_M = 0.748 eV. This combination yields high effective mobility, producing rapid grain growth that depletes the grain population early (Fig. 10a). Conversely, the smallest grain sizes (136 nm and 140 nm) arise from low M0M_0 and high QMQ_M: sample 307 has M0=1.95×10−16M_0 = 1.95 \times10^{-16} m4^4/(J⋅\cdots) and QM=1.04Q_M = 1.04 eV, while sample 114 has M0=4.11×10−16M_0 = 4.11 \times10^{-16} m4^4/(J⋅\cdots) and QM=1.05Q_M = 1.05 eV (1.18×\times mean). As shown in Figs. 11b and 11c, the GB energy γ\gamma varies between 0.59 and 1.72 times the mean across extreme cases without consistently correlating to grain size, confirming its weaker influence relative to M0M_0 and QMQ_M identified in detail later in the Sobol analysis.

PCA dimensionality reduction

PCA of the grain size evolution trajectories across 330 simulation runs and up to 5000 s reveals that the variance is highly concentrated in the first few components. PC1 explains 95.94% of the total variance, while PC2 explains 2.98% of the total variance. Together, these PCs retain 98.92% of the original signal variance. The reconstruction diagnostics show a relative root mean square error (RMSE) of nearly 0 when using the first two PCs to reconstruct the full trajectories, indicating that they capture nearly all relevant dynamical features of grain growth, with PC1 describing the dominant growth trend and PC2 capturing secondary deviations from this trend.

GP surrogate model performance

Gaussian process surrogate models were trained to map the input parameter space (M0M_0, QMQ_M, γ\gamma) to the PC scores. The predictive capability of these models was rigorously assessed using a 25-fold repeated five-fold cross-validation strategy. The models demonstrate exceptional accuracy across all splits. For PC1, the minimum observed R2R^2 across all splits was 99.996%, and the minimum Q2Q^2 was 98.46%, indicating near-perfect reconstruction of the dominant growth mode. For PC2, which captures finer, lower-magnitude variations, the minimum R2R^2 was 99.972% and the minimum Q2Q^2 was 90.34%, reflecting somewhat greater difficulty in predicting the secondary mode but still maintaining strong generalization capability. The learned noise variances in standardized PC space are 8.74×10−58.74 \times10^{-5} for PC1 and 5.26×10−45.26 \times10^{-4} for PC2, confirming that the surrogate models successfully learn smooth, low-noise representations of the underlying phase-field simulations.

Figure 11. Parameter space locations of extreme grain sizes.

Global sensitivity analysis

Time-resolved Sobol indices reveal distinct temporal evolution patterns for the three uncertain input parameters (Figure 12). At the earliest time point (t≈0t \approx0 s), M0M_0 exhibits the highest first-order sensitivity index (S1=0.268S_1 = 0.268) and total effect (St=0.769S_t = 0.769), followed by QMQ_M (S1=0.179S_1 = 0.179, St=0.653S_t = 0.653) and γ\gamma (S1=0.017S_1 = 0.017, St=0.132S_t = 0.132). The large gap between S1S_1 and StS_t for all three parameters indicates substantial higher-order interactions at early times, when the system has not yet reached the asymptotic parabolic growth regime.

Figure 12. Time-resolved Sobol sensitivity indices for: (a) mobility prefactor M0M_0, (b) activation energy QMQ_M, and (c) GB energy γ\gamma. Solid lines represent total-effect indices (StS_t), dashed lines represent first-order indices (S1S_1), and shaded regions indicate 95% confidence intervals (CI) from |SALib|.

As grain growth progresses, the sensitivity indices evolve systematically. The first-order sensitivity of M0M_0 increases monotonically from S1=0.268S_1 = 0.268 at t≈0t \approx0 s to S1=0.481S_1 = 0.481 at t=5000t = 5000 s, while its total effect decreases from St=0.769S_t = 0.769 to St=0.629S_t = 0.629. Conversely, QMQ_M exhibits an initial increase in S1S_1 from 0.179 to approximately 0.282 by t≈1300t \approx1300 s, followed by a plateau that stabilizes near S1≈0.28S_1 \approx0.28. For γ\gamma, the first-order sensitivity increases from S1=0.017S_1 = 0.017 at early times to S1=0.072S_1 = 0.072 at late times, while its total effect remains nearly constant at St≈0.12S_t \approx0.12–0.130.13 throughout the entire simulation.

The convergence of S1S_1 and StS_t for all three parameters at late times indicates diminishing higher-order interactions as the system approaches the asymptotic parabolic regime described by (4). At t=5000t = 5000 s, the sum of first-order indices approaches unity (∑S1≈0.83\sum S_1 \approx0.83), confirming that parameter interactions become negligible compared to individual contributions. However, a notable gap persists between the sum of first-order indices and unity, indicating that approximately 15–20% of the system variance is driven by nonlinear interactions between the parameters rather than their isolated effects. For instance, at t=4038t = 4038 s, the total effect for M0M_0 is St=0.631S_t = 0.631 while its first-order index is S1=0.476S_1 = 0.476, demonstrating that interactions contribute roughly St−S1=0.155S_t - S_1 = 0.155 (or 15.5%) to the total sensitivity of M0M_0.

The sensitivity hierarchy S1(M0)>S1(QM)>S1(γ)S_1(M_0) > S_1(Q_M) > S_1(\gamma) is primarily driven by the Arrhenius dependence M=M0exp⁡(−QM/(kBT))M = M_0 \exp(-Q_M/(k_B T)), through which uncertainties in M0M_0 and QMQ_M are exponentially amplified, whereas γ\gamma enters the growth rate linearly and with comparatively smaller absolute uncertainty. At late times (t=5000t = 5000 s), M0M_0 accounts for approximately 48% of output variance in first-order effects and 63% including interactions, QMQ_M contributes 28% (first-order) to 42% (total), and γ\gamma accounts for only 7% (first-order) to 12% (total). These findings highlight the critical importance of accurate mobility measurements for predictive grain growth modeling in UN, and suggest that future experimental efforts should prioritize reducing uncertainty in M0M_0 and QMQ_M over further refinement of γ\gamma.

Discussion

The central methodological contribution of this work is the extraction of a drag-free GB mobility for UN from the only available grain growth dataset [23]. We show that pore drag is negligible under the microstructural conditions of Ronchi and Sari: the pore-drag analysis yields mobility reduction factors s≈0.93s \approx0.93–0.990.99, and the cubic and parabolic kinetic models are statistically indistinguishable (ΔR2=0.009\Delta R^2 = 0.009). The effective mobility therefore directly represents the intrinsic GB mobility.

Three sources of uncertainty limit the precision of this result. First, the surface diffusivity in the pore mobility model ((31)) was approximated from UO2_2 data [69], as no measurements or atomistic calculations exist for UN. Second, the experimental dataset comprises only five temperature points at a single annealing time (500 h), which is insufficient to determine M0M_0 and QMQ_M with high confidence. Third, the material studied was (U,Pu)N rather than pure UN. Solute drag from Pu cannot be quantified without dedicated experiments. The extracted mobility should therefore be treated as an order-of-magnitude estimate. Dedicated isothermal grain growth experiments on high-purity UN pellets over a wider temperature range are needed to refine these parameters.

It is instructive to compare the intrinsic GB mobility of UN with those reported for UO2_2 [13, 18] and U3_3Si2_2 [20], the two other actinide fuel systems for which phase-field grain growth models exist. Figure 13 shows the drag-free grain growth predicted by (4) at 1500 K for all three materials over 10 days. Despite having the largest activation energy by far (QM=3.01Q_M = 3.01 eV versus 0.89 eV for UN and 0.33 eV for U3_3Si2_2), UO2_2 grows the fastest, reaching D≈4.40D \approx4.40 μ\mum after 10 days. This is a direct consequence of its exceptionally large prefactor (M0=2.14×10−7M_0 = 2.14 \times10^{-7} m4^4/(J⋅\cdots)), which overwhelms the Arrhenius suppression at this temperature. UN reaches D≈2.28D \approx2.28 μ\mum, and U3_3Si2_2 grows the least, reaching only D≈0.51D \approx0.51 μ\mum. UN occupies an intermediate position between the highly ionic UO2_2 and the intermetallic U3_3Si2_2, reflecting its mixed ionic-covalent bonding character.

Evolution of average grain size over time for UN, UO2, and U3Si2

Figure 13. Evolution of average grain size D(t)D(t) at T=1500T = 1500 K for UO2_2, UN, and U3_3Si2_2, assuming drag-free curvature-driven growth with an initial grain size of D0=0.1D_0 = 0.1 µm.

The phase-field simulations represent the drag-free limit of grain growth in UN. Solute drag, pore-boundary interactions, irradiation-induced defects, and thermal gradient driving forces are all absent. The predicted grain sizes are therefore upper bounds on curvature-driven coarsening at each temperature. Including these resistive mechanisms is a necessary step toward more realistic simulations.

A limitation of the present simulations is their 2D nature. While 2D grain growth captures the correct qualitative behavior, the geometric factor α=1/2\alpha= 1/2 in (3) differs from the value α=1\alpha= 1 appropriate for 3D equiaxed grains, so the predicted growth rates are a factor of two lower than those expected in bulk pellets. Despite this, the 2D framework is sufficient for the objectives of this study—i.e., demonstrating normal grain growth, validating the Hillert-like grain size distribution, and performing the sensitivity analysis—all of which are qualitatively insensitive to dimensionality.

The average GB energy correlation ((19)) fits the MD data well over 0–2000 K (R2=0.983R^2 = 0.983), but the T5T^5 term grows rapidly and the fit should not be extrapolated beyond this range.

The initial grain size distribution is not explicitly included in the uncertainty analysis. Instead, its effect is approximated by averaging grain growth over ten independent Voronoi tessellations. A more complete framework would parameterize this distribution explicitly—for instance, through moments of kernel density estimates fitted to each tessellation—and include these as additional uncertain inputs. This would quantify the joint effect of kinetic uncertainty and structural randomness on grain evolution, and represents a natural direction for future work.

Despite the limitations discussed above, this study establishes the first integrated multiscale modeling framework for grain growth in UN. It provides the community with temperature-dependent GB energies for 27 symmetric tilt boundaries, a rigorous and transferable procedure for extracting drag-free GB mobility from scarce experimental data, the first quantitative grain growth kinetics for UN, and clear experimental priorities identified through time-resolved global sensitivity analysis. This physics-informed, uncertainty-aware framework is directly applicable to fuel performance codes and extensible to other advanced nuclear fuel systems.

Conclusions

This work presents an integrated multiscale framework for grain growth in uranium mononitride, combining MD-based GB energy calculations, phenomenological mobility extraction, phase-field simulations, and surrogate-assisted uncertainty quantification.

The Tseplyaev potential [35] yields GB energies consistent with DFT values across all 27 symmetric tilt boundaries studied, whereas the Kocevski potential [36] systematically underestimates them due to anomalous U-U repulsion that prevents GB closure upon 0 K minimization. The average GB energy is nearly temperature-independent below 1000 K and increases at higher temperatures, well described by:

γ(T)=1.382+3.279×10−6T+5.748×10−18T5(J/m2),\gamma(T) = 1.382 + 3.279 \times10^{-6} T + 5.748 \times10^{-18} T^{5}\quad(\mathrm{J}/\mathrm{m}^{2}),

with R2=0.983R^{2} = 0.983. The standard deviation of the 27 GB energies is approximately 30% of the mean at all temperatures, reflecting the spread of GB energies across misorientation angles.

A mechanistic pore-drag analysis, based on the Powers-Glaeser [16] framework with partial pore-GB coupling, applied to the Ronchi and Sari [23] dataset yields mobility reduction factors s≈0.93s \approx0.93–0.990.99, statistically indistinguishable from unity. The cubic and parabolic kinetic models are equally consistent with the experimental data (ΔR2=0.009\Delta R^{2} = 0.009), confirming that pore drag is negligible under the microstructural conditions of those experiments. The intrinsic GB mobility is therefore identified with the effective mobility:

M(T)=2.05×10−15exp⁡(−0.89 eVkBT) m4/(J⋅s).M(T) = 2.05 \times10^{-15} \exp\left(-\frac{0.89\ \mathrm{eV}}{k_{\mathrm{B}}T}\right)\ \mathrm{m}^{4}/(\mathrm{J}\cdot\mathrm{s}).

Phase-field simulations over 1500–2000 K confirm normal curvature-driven grain growth, with (D2−D02)(D^{2}-D_{0}^{2}) evolving linearly in time and grain size distributions converging to the Hillert-like form independently of the initial microstructure. The coefficient of variation across ten independent Voronoi microstructures saturates exponentially at each temperature, with the asymptotic value increasing from CV0≈0.053\mathrm{CV}_{0} \approx0.053 at 1500 K to CV0≈0.120\mathrm{CV}_{0} \approx0.120 at 2000 K, and the characteristic saturation time decreasing from approximately 3360 s to 875 s over the same range.

The surrogate-assisted global sensitivity analysis, combining PCA, Gaussian process regression, and Sobol decomposition, reveals a clear and persistent sensitivity hierarchy. The mobility prefactor M0M_{0} dominates output variance at all times, reaching S1≈0.48S_{1} \approx0.48 and St≈0.63S_{t} \approx0.63 at t=5000t = 5000 s, followed by the activation energy QMQ_{M} (S1≈0.28S_{1} \approx0.28, St≈0.42S_{t} \approx0.42), while the GB energy γ\gamma contributes minimally (S1≈0.07S_{1} \approx0.07, St≈0.12S_{t} \approx0.12). This hierarchy reflects the exponential amplification of Arrhenius parameter uncertainty relative to the linear entry of γ\gamma into the grain growth rate. The convergence of S1S_{1} and StS_{t} at late times confirms that parameter interactions diminish as the system approaches the asymptotic parabolic growth regime. Reducing uncertainty in M0M_{0} and QMQ_{M} through dedicated isothermal experiments on high-purity UN over a wide temperature range is therefore the highest-priority need for predictive grain growth modeling in this material.

Acknowledgments

The authors thank Xu Wu for the fruitful discussions and useful suggestions. This research made use of the resources of the High-Performance Computing Center at Idaho National Laboratory, which is supported by the Office of Nuclear Energy of the U.S. Department of Energy and the Nuclear Science User Facilities under Contract No. DE-AC07-05ID14517.

References

  1. [1]J. Wallenius, Nitride fuels, Comprehensive Nuclear Materials 5 (2020) 88–101. doi: 10.1016/B978-0-12-803581-8.11694-7.DOI
  2. [2]M. Uno, T. Nishi, M. Takano, Thermodynamic and thermophysical properties of the actinide nitrides, Comprehensive Nuclear Materials: Second Edition (2020) 202–231doi:10.1016/B978-0-12-803581-8.11749-7.DOI
  3. [3]M. AbdulHameed, B. Beeler, A. Claisse, Ab initio molecular dynamics of paramagnetic uranium mononitride (un) using disordered local moments, Computational Materials Science 260 (2025) 114115. doi:https://doi.org/10.1016/j.commatsci.2025.114115.
  4. [4]M. AbdulHameed, B. Beeler, C. O. Galvin, M. W. Cooper, Assessment of uranium nitride interatomic potentials, Journal of Nuclear Materials 600 (2024) 155247. doi:https://doi.org/10.1016/j.jnucmat.2024.155247.
  5. [5]M. AbdulHameed, B. Beeler, The contribution of nitrogen frenkel-pair formation to the high-temperature heat capacity of uranium mononitride, Computational Materials Science 272 (2026) 114827. doi:https://doi.org/10.1016/j.commatsci.2026.114827.
  6. [6]M. AbdulHameed, B. Beeler, A. Claisse, Atomistic investigation of plastic deformation and dislocation motion in uranium mononitride, Applied Sciences 15 (5) (2025). doi:10.3390/app15052666.DOI
  7. [7]M. AbdulHameed, B. Beeler, C. O. Galvin, M. W. Cooper, N. Elamrawy, A. Claisse, Molecular-dynamics study of diffusional creep in uranium mononitride, Journal of Nuclear Materials 617 (2025) 156153. doi:https://doi.org/10.1016/j.jnucmat.2025.156153.
  8. [8]M. W. Cooper, J. Rizk, C. Matthews, V. Koevcski, G. T. Craven, T. Gibson, D. A. Andersson, Simulations of self- and Xe diffusivity in uranium mononitride including chemistry and irradiation effects, Journal of Nuclear Materials 587 (2023). doi:10.1016/j.jnucmat.2023.154685.DOI
  9. [9]A. Schneider, J. Rizk, M. Kosmidou, C. Matthews, D. A. Andersson, M. W. Cooper, Radiation induced athermal diffusivity in uranium mononitride, Journal of Nuclear Materials 601 (2024) 155313. doi:https://doi.org/10.1016/j.jnucmat.2024.155313.
  10. [10]J. T. Rizk, M. W. Cooper, P.-C. A. Simon, A. J. Schneider, D. A. Andersson, S. R. Novascone, C. Matthews, Mechanistic nuclear fuel performance modeling of uranium nitride, Journal of Nuclear Materials 606 (2025) 155604. doi:https://doi.org/10.1016/j.jnucmat.2024.155604.
  11. [11]M. AbdulHameed, A. J. Schneider, B. Beeler, M. W. Cooper, Modeling oxygen-void interactions in uranium nitride (2026). doi:https://doi.org/10.1016/j.jnucmat.2026.156983.
  12. [12]J. B. Ainscough, B. W. Oldfield, J. O. Ware, Isothermal grain growth kinetics in sintered UO₂ pellets, Journal of Nuclear Materials 49 (1973). doi:10.1016/0022-3115(73)90001-9.DOI
  13. [13]M. R. Tonks, Y. Zhang, X. Bai, P. C. Millett, Demonstrating the temperature gradient impact on grain growth in UO₂ using the phase field method, Materials Research Letters 2 (2014). doi:10.1080/21663831.2013.849300.DOI
  14. [14]D. Kaoumi, A. T. Motta, R. C. Birtcher, Grain growth in nanocrystalline metal thin films under in situ ion-beam irradiation, Journal of ASTM International 4 (2007). doi:10.1520/JAI100743.DOI
  15. [15]D. Kaoumi, A. T. Motta, R. C. Birtcher, A thermal spike model of grain growth under irradiation, Journal of Applied Physics 104 (2008). doi:10.1063/1.2988142.DOI
  16. [16]J. D. Powers, A. M. Glaeser, Grain boundary migration in ceramics, Interface Science 6 (1998). doi:10.1023/a:1008656302007.DOI
  17. [17]J. French, X. M. Bai, Molecular dynamics studies of grain boundary mobility and anisotropy in BCC γ-uranium, Journal of Nuclear Materials 565 (2022). doi:10.1016/j.jnucmat.2022.153744.DOI
  18. [18]X. M. Bai, Y. Zhang, M. R. Tonks, Testing thermal gradient driving force for grain boundary migration using molecular dynamics simulations, Acta Materialia 85 (2015). doi:10.1016/j.actamat.2014.11.019.DOI
  19. [19]M. R. Tonks, P. C. A. Simon, J. Hirschhorn, Mechanistic grain growth model for fresh and irradiated UO₂ nuclear fuel, Journal of Nuclear Materials 543 (2021). doi:10.1016/j.jnucmat.2020.152576.DOI
  20. [20]A. Cheniour, M. R. Tonks, B. Gong, T. Yao, L. He, J. M. Harp, B. Beeler, Y. Zhang, J. Lian, Development of a grain growth model for U₃Si₂ using experimental data, phase field simulation and molecular dynamics, Journal of Nuclear Materials 532 (2020). doi:10.1016/j.jnucmat.2020.152069.DOI
  21. [21]G. Giudicelli, A. Lindsay, L. Harbour, C. Icenhour, M. Li, J. E. Hansel, P. German, P. Behne, O. Marin, R. H. Stogner, J. M. Miller, D. Schwen, Y. Wang, L. Munday, S. Schunert, B. W. Spencer, D. Yushu, A. Recuero, Z. M. Prince, M. Nezdyur, T. Hu, Y. Miao, Y. S. Jung, C. Matthews, A. Novak, B. Langley, T. Truster, N. Nobre, B. Alger, D. Andrš, F. Kong, R. Carlsen, A. E. Slaughter, J. W. Peterson, D. Gaston, C. Per-mann, 3.0 - MOOSE: Enabling massively parallel multiphysics simulations, SoftwareX 26 (2024) 101690. doi:https://doi.org/10.1016/j.softx.2024.101690.
  22. [22]D. Schwen, L. Aagesen, J. Peterson, M. Tonks, Rapid multiphase-field model development using a modular free energy based approach with automatic differentiation in MOOSE/MARMOT, Computational Materials Science 132 (2017) 36–45. doi:https://doi.org/10.1016/j.commatsci.2017.02.017.
  23. [23]C. Ronchi, C. Sari, Swelling analysis of highly rated MX-type LMFBR fuels: I. Restructuring and porosity behaviour, Journal of Nuclear Materials 58 (1975). doi:10.1016/0022-3115(75)90100-2.DOI
  24. [24]K. D. Johnson, D. A. Lopes, Grain growth in uranium nitride prepared by spark plasma sintering, Journal of Nuclear Materials 503 (2018). doi:10.1016/j.jnucmat.2018.02.041.DOI
  25. [25]M. A. Tschopp, D. L. McDowell, Structures and energies of Σ3 asymmetric tilt grain boundaries in copper and aluminium, Philosophical Magazine 87 (2007). doi:10.1080/14786430701255895.DOI
  26. [26]M. A. Tschopp, D. L. McDowell, Asymmetric tilt grain boundary structure and energy in copper and aluminium, Philosophical Magazine 87 (2007). doi:10.1080/14786430701455321.DOI
  27. [27]Y. Shibuta, S. Takamoto, T. Suzuki, A molecular dynamics study of the energy and structure of the symmetric tilt boundary of iron, ISIJ International 48 (2008). doi:10.2355/isijinternational.48.1582.DOI
  28. [28]B. Beeler, M. Baskes, D. Andersson, M. W. Cooper, Y. Zhang, Molecular dynamics investigation of grain boundaries and surfaces in U₃Si₂, Journal of Nuclear Materials 514 (2019). doi:10.1016/j.jnucmat.2018.12.008.DOI
  29. [29]Y. Wang, J. Zhao, Y. Jiang, L. Xi, J. Zhao, Oxidation susceptibility of UN Σ5(210) grain boundary with Al/Cr/Ni dopant: A first-principles study, Journal of Nuclear Materials 578 (2023). doi:10.1016/j.jnucmat.2023.154344.DOI
  30. [30]M. Hillert, On the theory of normal and abnormal grain growth, Acta Metallurgica 13 (1965). doi:10.1016/0001-6160(65)90200-2.DOI
  31. [31]S. Protasova, V. Sursaeva, Triple junctions effect on the grain growth in nanostructured materials, in: Interface Science, Vol. 9, 2001. doi:10.1023/A:1015123214987.DOI
  32. [32]H. Hu, B. B. Rath, On the time exponent in isothermal grain growth, Metallurgical Transactions 1 (1970). doi:10.1007/BF03038435.DOI
  33. [33]W. D. Kingery, B. François, Grain growth in porous compacts, Journal of the American Ceramic Society 48 (1965). doi:10.1111/j.1151-2916.1965.tb14665.x.DOI
  34. [34]A. P. Thompson, H. M. Aktulga, R. Berger, D. S. Bolintineanu, W. M. Brown, P. S. Crozier, P. J. in ’t Veld, A. Kohlmeyer, S. G. Moore, T. D. Nguyen, R. Shan, M. J. Stevens, J. Tranchida, C. Trott, S. J. Plimpton, LAMMPS–a flexible simulation tool for particle-based materials modeling at the atomic, meso, and continuum scales, Computer Physics Communications 271 (2022). doi:10.1016/j.cpc.2021.108171.DOI
  35. [35]V. I. Tseplyaev, S. V. Starikov, The atomistic simulation of pressure-induced phase transition in uranium mononitride, Journal of Nuclear Materials 480 (2016) 7–14. doi:10.1016/j.jnucmat.2016.07.048.DOI
  36. [36]V. Kocevski, M. W. Cooper, A. J. Claisse, D. A. Andersson, Development and application of a uranium mononitride (UN) potential: Thermomechanical properties and Xe diffusion, Journal of Nuclear Materials 562 (2022). doi:10.1016/j.jnucmat.2022.153553.DOI
  37. [37]P. Hirel, Atomsk: A tool for manipulating and converting atomic data files, Computer Physics Communications 197 (2015). doi:10.1016/j.cpc.2015.07.012.DOI
  38. [38]A. Stukowski, Visualization and analysis of atomistic simulation data with OVITO–the open visualization tool, Modelling and Simulation in Materials Science and Engineering 18 (2010). doi:10.1088/0965-0393/18/1/015012.DOI
  39. [39]W. Cai, W. Nix, Imperfections in Crystalline Solids, 1st Edition, Cambridge University Press, 2016. doi:10.1017/cbo9781316389508.DOI
  40. [40]R. Abbaschian, L. Abbaschian, Physical Metallurgy Principles, 5th Edition, Cengage Learning, 2025.
  41. [41]T. Seki, T. Futazuka, N. Morishige, R. Matsubara, Y. Ikuhara, N. Shibata, Incommensurate grain-boundary atomic structure, Nature Communications 14 (2023). doi:10.1038/s41467-023-43536-0.DOI
  42. [42]H. Grimmer, W. Bollmann, D. H. Warrington, Coincidence-site lattices and complete pattern-shift in cubic crystals, Acta Crystallographica Section A 30 (1974). doi:10.1107/S056773944000043X.DOI
  43. [43]J. Zhao, B. L. Adams, Definition of an asymmetric domain for intercrystalline misorientation in cubic materials in the space of Euler angles, Acta Crystallographica Section A 44 (1988). doi:10.1107/S010876738701256X.DOI
  44. [44]A. A. Riet, J. A. V. Orman, D. J. Lacks, A molecular dynamics study of grain boundary diffusion in mgo, Geochimica et Cosmochimica Acta 292 (2021). doi:10.1016/j.gca.2020.09.012.DOI
  45. [45]L. Q. Chen, W. Yang, Computer simulation of the domain dynamics of a quenched system with a large number of nonconserved order parameters: The grain-growth kinetics, Physical Review B 50 (1994). doi:10.1103/PhysRevB.50.15752.DOI
  46. [46]L. Q. Chen, A novel computer simulation technique for modeling grain growth, Scripta Metallurgica et Materialia 32 (1995). doi:10.1016/S0956-716X(99)80022-3.DOI
  47. [47]N. Moelans, B. Blanpain, P. Wollants, Quantitative analysis of grain boundary properties in a generalized phase field model for grain growth in anisotropic systems, Physical Review B - Condensed Matter and Materials Physics 78 (2008). doi:10.1103/PhysRevB.78.024113.DOI
  48. [48]G. Gottstein, A. H. King, L. S. Shvindlerman, Effect of triple-junction drag on grain growth, Acta Materialia 48 (2000). doi:10.1016/S1359-6454(99)00373-0.DOI
  49. [49]K. J. Ko, P. R. Cha, J. T. Park, J. K. Kim, N. M. Hwang, Phase field model simulation of grain growth in three dimensions under isotropic and anisotropic grain boundary energy conditions, in: Materials Science Forum, Vol. 558-559, 2007. doi:10.4028/0-87849-443-x.1101.DOI
  50. [50]N. Moelans, B. Blanpain, P. Wollants, An introduction to phase-field modeling of microstructure evolution, CALPHAD: Computer Coupling of Phase Diagrams and Thermochemistry 32 (2008). doi:10.1016/j.calphad.2007.11.003.DOI
  51. [51]C. J. Permann, M. R. Tonks, B. Fromm, D. R. Gaston, Order parameter re-mapping algorithm for 3D phase field model of grain growth using FEM, Computational Materials Science 115 (2016). doi:10.1016/j.commatsci.2015.12.042.DOI
  52. [52]E. Schüle, A justification of the Hillert distribution by spatial grain growth simulation performed by modifications of Laguerre tessellations, Computational Materials Science 5 (1996). doi:10.1016/0927-0256(96)00004-3.DOI
  53. [53]T. Breithaupt, L. N. Hansen, S. Toppaladoddi, R. F. Katz, The role of grain-environment heterogeneity in normal grain growth: A stochastic approach, Acta Materialia 209 (2021). doi:10.1016/j.actamat.2021.116699.DOI
  54. [54]M. Yaseen, X. Wu, Quantification of deep neural network prediction uncertainties for VVUQ of machine learning models, Nuclear Science and Engineering 197 (2023). doi:10.1080/00295639.2022.2123203.DOI
  55. [55]M. Yaseen, A. Sadek, W. Osman, M. Altahhan, X. Wu, M. Avramova, K. Ivanov, Sensitivity and uncertainty analysis in pebble-bed reactors: A study using the High-Temperature Code Package (HCP), Annals of Nuclear Energy 219 (2025) 111428. doi:10.1016/j.anucene.2025.111428.DOI
  56. [56]F. M. Nasr, M. Tano, P. Sabharwall, Y. Azmy, Global sensitivity analysis using Gaussian process surrogate models & impact of thermophysical properties uncertainties on the steady-state operation of molten salt reactors, Annals of Nuclear Energy 217 (2025) 111304. doi:10.1016/j.anucene.2025.111304.DOI
  57. [57]F. M. Nasr, M. Tano, M. Yaseen, Y. Azmy, Transient uncertainty quantification and global sensitivity analysis of the open-source Molten Chloride Reactor Experiment (MCRE) using GP-PCA surrogate models, manuscript submitted for publication (2025).DOI
  58. [58]R. G. McClarren, Uncertainty Quantification and Predictive Computational Science, Springer, 2018.DOI
  59. [59]A. G. d. G. Matthews, M. van der Wilk, T. Nickson, K. Fujii, A. Boukouvalas, P. León-Villagrá, Z. Ghahramani, J. Hensman, GPflow: A Gaussian process library using TensorFlow, Journal of Machine Learning Research 18 (40) (2017) 1–6. URL http://jmlr.org/papers/v18/16-537.htmlarxiv.org/abs/1610.08733
  60. [60]M. van der Wilk, V. Dutordoir, S. John, A. Artemev, V. Adam, J. Hensman, A framework for interdomain and multioutput Gaussian processes, arXiv:2003.01115 (2020). URL https://arxiv.org/abs/2003.01115
  61. [61]F. Pedregosa, G. Varoquaux, A. Gramfort, V. Michel, B. Thirion, O. Grisel, M. Blondel, P. Prettenhofer, R. Weiss, V. Dubourg, J. Vanderplas, A. Passos, D. Cournapeau, M. Brucher, M. Perrot, E. Duchesnay, Scikit-learn: Machine learning in Python, Journal of Machine Learning Research 12 (2011) 2825–2830.arxiv.org/abs/1201.0490
  62. [62]I. Sobol, Sensitivity estimates for nonlinear mathematical models, Mathematical Modeling and Computational Experiment 1 (1993) 407–414. URL https://www.andreasaltelli.eu/file/repository/sobol1993.pdf
  63. [63]I. Sobol, Global sensitivity indices for nonlinear mathematical models and their Monte Carlo estimates, Mathematics and Computers in Simulation 55 (2001). doi:10.1016/S0378-4754(00)00270-6.DOI
  64. [64]A. Saltelli, P. Annoni, I. Azzini, F. Campolongo, M. Ratto, S. Tarantola, Variance based sensitivity analysis of model output: Design and estimator for the total sensitivity index, Computer Physics Communications 181 (2010). doi:10.1016/j.cpc.2009.09.018.DOI
  65. [65]J. Herman, W. Usher, SALib: An open-source Python library for sensitivity analysis, The Journal of Open Source Software 2 (9) (2017). doi:10.21105/joss.00097.DOI
  66. [66]T. Iwanaga, W. Usher, J. Herman, Toward SALib 2.0: Advancing the accessibility and interpretability of global sensitivity analyses, Socio-Environmental Systems Modelling 4 (2022) 18155. doi:10.18174/sesmo.18155.DOI
  67. [67]T. Froloy, Y. Mishin, Thermodynamics of coherent interfaces under mechanical stresses. II. application to atomistic simulation of grain boundaries, Physical Review B - Condensed Matter and Materials Physics 85 (2012). doi:10.1103/PhysRevB.85.224107.
  68. [68]D. R. Olander, A. T. Motta, Light Water Reactor Materials Volume I: Fundamentals, American Nuclear Society, 2017.
  69. [69]M. A. Muntaha, S. Chatterjee, S. Blondel, L. Aagesen, D. Andersson, B. D. Wirth, M. R. Tonks, Impact of grain boundary and surface diffusion on predicted fission gas bubble behavior and release in UO₂ fuel, Journal of Nuclear Materials 594 (2024). doi:10.1016/j.jnucmat.2024.155032.DOI
  70. [70]X. Li, Overview of trust-region methods, Frontiers in Computing and Intelligent Systems 8 (2024). doi:10.54097/hbsy3w97.DOI
  71. [71]R. Dorfman, A note on the δ-method for finding variance formulae, The Biometric Bulletin 1 (1938) 129–137.
  72. [72]H. Cramér, Mathematical Methods of Statistics, Princeton University Press, Princeton, NJ, 1946.

Paper details

vlnc:W_d37cytdy
Version
v1 · latest
Published
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents