WorksEngineering
Continuous Wideband Multicarrier Rydberg Atomic Quantum Receiver
Abstract
This paper investigates continuous wideband orthogonal frequency-division multiplexing (OFDM) reception using an auxiliary (AUX)-assisted five-level Rydberg atomic quantum receiver (RAQR) with a single microwave local oscillator (LO), without requiring additional atomic reception transitions or LO frequency combs. By exploiting Floquet theory, the proposed framework characterizes the dynamic atomic response at finite signal-LO detunings without relying on a quasi-static Taylor expansion around the LO operating point. Specifically, closed-form radio-frequency (RF)-to-electrical conversion expressions are derived from the Lindblad master equation under weak-probe and weak-signal approximations. Building on these expressions, an equivalent multicarrier communication model is established, revealing the inherent frequency selectivity of the atomic response and the resulting subcarrier-dependent amplitude and phase distortions. RAQR-aware zero-forcing (ZF) equalization is developed to enable reliable OFDM reception. Furthermore, analytical results reveal how LO and AUX driving influence the atomic response through dressed-state splitting and energy-level shifts. An upper bound on the LO-referenced half-power span is derived, and an approximately -dB reduction in center-response power per bandwidth doubling is established in the AUX-free strong-LO regime. Simulation results validate the analytical response model and reveal pronounced subcarrier-dependent amplitude and phase variations across over ~MHz, highlighting the potential of RAQRs as wideband receiving front ends for future wireless communications.
Introduction
Sixth-generation (6G) mobile networks are expected to support immersive services, ubiquitous connectivity, and integrated sensing and communication [1, 2, 3]. Realizing these goals requires wider signal bandwidths and reliable weak-signal reception within practical hardware and power budgets [4]. In conventional RF receivers, improving sensitivity may require a larger hardware implementation and higher power consumption, while wider bandwidth increases integrated noise power, making sensitivity harder to maintain within fixed hardware and power budgets [5], [6]. These challenges motivate the exploration of alternative physical mechanisms for wireless reception that complement continued advances in RF circuit design.
Rydberg atomic quantum receivers (RAQRs) offer an alternative reception mechanism by converting RF-induced changes in atomic coherence into optical signals [7]. The large transition dipole moments between Rydberg states enable sensitive interactions with incident RF fields [8]. Specifically, a resonant probe beam is strongly absorbed without a coupling laser, whereas adding the coupling laser under two-photon resonance suppresses absorption and establishes a narrow transmission window, which is known as electromagnetically induced transparency (EIT) [9]. Introducing a sufficiently strong RF field resonant with the transition between two Rydberg states then splits this EIT window into two resolved peaks, producing Autler-Townes splitting (ATS) [10]. Since the peak separation is proportional to the RF-field amplitude, this spectral splitting provides an optical means of measuring the field magnitude. To recover both amplitude and phase of the RF signal, atomic superheterodyne reception introduces a microwave local oscillator (LO) with a small frequency offset relative to the received signal, forming a time-varying optical readout. This superheterodyne architecture enables coherent RF reception for wireless communication networks [11].
Building on these detection mechanisms, RAQR research has progressed from experimental demonstrations of waveform recovery to analytical modeling of communication systems. Early experiments demonstrated reception of amplitude- and frequency-modulated microwave signals [12], [13]. Subsequent work investigated phase-shift-keyed reception [14], quadrature amplitude modulation (QAM) reception [15], and phase-modulated frequency-division multiplexing [16]. To improve robustness against receiver impairments, laser phase-noise compensation was incorporated into optically biased coherent detection [17]. In parallel, frequency-hopping recep-
Q. Peng, Q. Luo, and P. Xiao are affiliated with 5G and 6G Innovation Centre, Institute for Communication Systems (ICS) of the University of Surrey, Guildford, GU2 7XH, UK. (e-mail: {q.peng, q.u.luo,p.xiao}@surrey.ac.uk).
Maged Elkashlan is with Queen Mary University of London, United Kingdom. (E-mail: [email protected]).
Cunhua Pan is with the National Mobile Communications Research Laboratory, Southeast University, Nanjing, China. (e-mail: [email protected]; [email protected]).
George K. Karagiannidis is with the Department of Electrical and Computer Engineering, Aristotle University of Thessaloniki, Thessaloniki 54124, Greece (e-mail: [email protected]).
T. Q. Duong is with the Faculty of Engineering and Applied Science, Memorial University, St. John’s, NL A1C 5S7, Canada and also with the School of Electronics, Electrical Engineering and Computer Science, Queen’s University Belfast, Belfast, U.K. (e-mail: [email protected]) tion was investigated to enhance resilience to jamming by exploiting atomic frequency tunability [18]. Although these demonstrations establish the feasibility of atomic reception, translating this capability into system-level design requires tractable models that link incident electromagnetic signals to the resulting optical responses. To this end, an equivalent baseband model was derived using a Taylor expansion [19]. Subsequently the linear operating regime of this approximate model was characterized in [20]. Building on this model, RAQR-based reception has been investigated in self-sustained networks [21] and satellite communications [22]. These studies highlighted the potential of RAQRs as an alternative receiver technology for next-generation wireless networks.
Despite these advantages, high-sensitivity RAQR reception requires highly stable laser driving and a tightly controlled atomic environment. Fluctuations in laser detuning and power, together with atomic thermal motion, would significantly alter the atomic susceptibility and RF-to-optical conversion gain [23]. Furthermore, for wideband communications, conventional resonance-based RAQRs face two distinct constraints, namely limited instantaneous bandwidth and discontinuous high-sensitivity carrier coverage. The former is governed by optical driving and atomic relaxation dynamics [24], [25], whereas the latter arises from the discrete RF transitions between Rydberg states [26]. Therefore, broad carrier-frequency tunability does not guarantee simultaneous reception over a continuous band. These limitations motivate efforts to extend high-sensitivity carrier coverage and broaden the instantaneous response bandwidth for wideband multicarrier reception.
Several approaches have extended the frequency coverage and instantaneous bandwidth of RAQRs. Multilevel schemes enabled simultaneous reception through distinct Rydberg transitions, but their responses remained concentrated around separated resonances [27], [28]. To achieve continuous multicarrier reception, a five-level scheme combining auxiliary-field detuning with a microwave LO frequency comb was proposed in [29], although comb generation and careful intermediate-frequency allocation increased implementation complexity. Alternatively, six-wave mixing was investigated to broaden the RF-to-optical response through multiphoton interactions [30], [31]. More recently, auxiliary-microwave control was introduced to enhance the instantaneous response of a five-level configuration [32]. Despite these advances, understanding how the broadened atomic response supports continuous multicarrier reception with a single LO, while accounting for its inherent frequency selectivity and gain-bandwidth tradeoff, remains an important challenge.
Although the AUX-assisted five-level configuration in [32] demonstrated wideband microwave sensing, its broadband atomic response does not directly guarantee reliable multicarrier reception. In particular, real-valued IF readout introduces image overlap, while the frequency-selective atomic response causes subcarrier-dependent amplitude and phase distortions. To address these communication-specific challenges, we develop a single-LO OFDM reception framework without requiring an LO frequency comb. By integrating the Floquet-based atomic response with coherent optical detection, an equivalent multicarrier communication model and RAQR-aware equalizers are established. Beyond signal recovery, analytical results characterize the effects of LO and AUX driving on the center conversion gain and usable bandwidth, revealing a fundamental gain–bandwidth tradeoff. The main contributions are summarized as follows:
Floquet-based wideband conversion model. Building on the first-order Floquet response of the AUX-assisted five-level configuration, we derive a communication-oriented RF-to-electrical transfer function incorporating coherent optical readout. Unlike quasi-static Taylor expansions around the LO operating point, the proposed model captures finite-frequency atomic dynamics and the resulting amplitude and phase responses. Simulation results validate the derived expressions and demonstrate a one-sided LO-referenced bandwidth over 11 MHz under the considered parameters, highlighting the potential of RAQRs as wideband receiving front ends.
Single-LO wideband OFDM reception. We extend the proposed reception scheme to wideband OFDM using a single microwave LO, without an LO frequency comb. An equivalent fast Fourier transform (FFT)-domain input-output model is derived to characterize the inherently frequency-selective atomic response, which introduces subcarrier-dependent amplitude and phase distortions even under a frequency-flat wireless channel. To address these distortions, we develop RAQR-aware frequency-domain equalizers that jointly compensate for the wireless and atomic responses.
Analytical characterization of LO/AUX response control. Under the far-detuned AUX approximation, a reduced complex-response model is derived to characterize the resonance locations, modal linewidths, and center atomic conversion gain. The analysis reveals that LO driving controls the dressed-state splitting and linewidths, whereas AUX driving shifts the bright-state resonances and modifies the center response through distinct energy-level shifts. We further establish an explicit condition for AUX-induced gain enhancement, providing analytical guidance for shaping the atomic frequency response.
Bandwidth upper bound and gain–bandwidth trade-off. We derive an analytical upper bound on the one-sided LO-referenced bandwidth and establish a quantitative gain-bandwidth tradeoff for the AUX-free case. In the strong-LO regime with a contiguous passband, doubling the bandwidth incurs an approximately 18-dB loss in center-response power, implying an equivalent sensitivity penalty under fixed readout-noise conditions. Simulation results validate the bandwidth bound and corroborate the analyzed gain-bandwidth tradeoff.
The remainder of this paper is organized as follows. Section II presents the five-level atomic model, and Section III derives the optical response and its equivalent multicarrier representation. Section IV analyzes the tradeoff between gain and bandwidth. Section V presents simulation results, and Section VI concludes the paper.
System Model
Five-Level Floquet–Lindblad Model for Atomic Response
In Figure 1, we consider a five-level configuration with the basis , where is the ground state, represents the excited state, and , , and are Rydberg states. The probe and coupling lasers drive and with Rabi frequencies and . The LO and weak RF signal drive with Rabi amplitudes and , while the AUX field drives with . The signal-LO angular-frequency offset is , where and are the angular frequencies of the signal MW and the LO MW, respectively. The angular frequencies of probe, coupling, and AUX MW are denoted as , , and , respectively. Furthermore, the constant phases of the probe, coupling, LO, and AUX fields are absorbed into the atomic basis, allowing their Rabi frequencies to be taken as real and nonnegative. By applying the rotating-wave approximation, the Hamiltonian is written as

Figure 1. Continuous wideband RAQR based on a 5-level configuration.
where denotes the reduced Planck constant. Here, is the phase shift between the MW signal () and LO (). , , and are given by
and
where is the AUX-MW-induced alternating current (AC) Stark shift1, and denotes the dipole moment between level and . , , , and denote the detunings of the probe laser, coupling laser, LO MW, and AUX MW, respectively. denotes the detuning of the AUX MW with respect to the transition.
From (1), the Hamiltonian can be decomposed as
where , and are expressed as
and
Therefore, the LO MW is included in the time-independent part , while the received signal MW appears as a time-periodic perturbation at the intermediate angular frequency .
Let denote the density matrix of the atomic system and mean the -th element of . The density matrix is governed by the Lindblad master equation [32]
where is the relaxation matrix and is the repopulation matrix. denotes the spontaneous population decay rate of state , is a phenomenological approximation for the three Rydberg population decay rates, and represents the effective dephasing rate, including the transit broadening, the residual two-photon Doppler dephasing, and the dipole–dipole broadening.
To obtain the response at the intermediate frequency , we use the Floquet theory. Under the weak-signal condition, i.e., , the density matrix is approximated by
where is the zeroth-order density matrix induced by the probe laser, coupling laser, LO MW, and AUX MW, while and are the first-order sideband density matrices induced by the weak signal MW. Then, the power of the output probe beam is related to , which is given by
where means the power of the input probe beam and is the length of vapor cell. represents the constant term, is the atomic number density, is the probe wavenumber, and is the effective dipole moment.
Wideband Reception Model
This section derives approximate closed-form expressions for the optical response using Floquet theory and then develops the corresponding wideband multicarrier reception model.
Output Probe Beam
As can be seen from (9), it is challenging to derive the exact expression of the output probe beam. To tackle this issue, we derive the closed-form expression of under the following physically motivated assumptions. Particularly, we assume that the system operates in the weak-probe regime [32], i.e., , , . Based on these assumptions, the optical coherence can be expanded as
Then, the closed-form expression of the steady-state optical coherence is given by
where
Furthermore, and are given by
and
where
In (18), and . The detailed derivation is provided in Appendix A.
By using the first-order coherence approximation and substituting (12) into (11), we have
where is given by
Since and are first-order small quantities induced by the weak signal field, the exponential term can be linearized by using . Therefore, we have
Meanwhile, the corresponding phase of the transmitted probe beam is approximated as
where and is the phase of the input probe beam.
Equivalent Model
To improve the optical readout sensitivity, balanced coherent optical detection (BCOD) is adopted [19]. The transmitted probe beam can be expressed as
A phase-coherent reference optical beam is introduced as
where and denote the power and phase of the reference optical beam, respectively.
After combining the transmitted probe and the reference optical beam through a beam splitter and subtracting the photocurrents of the two photodetectors, the BCOD output voltage is given by
Following the electrical-gain convention in [19], is the linear post-detection power gain. The quantities and are the photodetector responsivity and load resistance, respectively. For simplicity, we assume that the reference beam is phase aligned with the steady-state transmitted probe, i.e., . Consequently, can be approximated as , under the weak-signal condition, i.e., . Then, substituting (21) and (22) into (25) and retaining only the first-order terms with respect to , we have
where
and
We next derive an idealized steady-state communication model from the output voltage. The symbol interval of duration is , during which the wireless channel coefficient and transmitted symbol are assumed to remain constant. Then, the Rabi frequency is determined by the amplitude of the received signal MW , where , , and denote the transmit power, transmit antenna gain, and propagation distance, respectively. and denote the wireless channel coefficient and transmitted information during the current symbol interval. Furthermore, the received signal phase and its phase relative to the LO MW are and respectively. Substituting these results into (28), we have
Then, the imaginary part of can be rewritten as
We assume ideal coherent downconversion followed by low-pass filtering to reject the image at angular frequency . For the finite-interval projection below, a nonzero IF satisfying , , is selected, and thus the image term integrates to zero over the symbol interval. The recovered complex baseband symbol is given by
where denotes the conversion gain. Therefore, the received symbol is
where . Following [19], we model the aggregate quantum projection noise, photon shot noise, and intrinsic thermal noise at the demodulator output as equivalent complex Gaussian noise, .
Multicarrier Extension
We next extend the single-carrier model to an idealized one-sided OFDM signal with subcarriers and a useful symbol duration of [33, 34]. Consistent with the preceding ideal-detection assumptions, cyclic-prefix overhead, atomic memory across symbol boundaries, and transient effects are neglected. Let and denote the subcarrier index and the angular-frequency offset between the -th signal subcarrier and the LO MW, respectively. Similar to the single-carrier case, we consider an arbitrary multicarrier symbol interval of duration and assume that the wireless channel remains approximately constant within this interval. Consequently, the channel coefficient and transmitted symbol are treated as constants over the considered symbol interval, and the symbol index is omitted for notational simplicity.
The phase shift between the received signal of the -th subcarrier and the LO MW is , where . Then, the Rabi-frequency amplitude is written as
where denotes the average power allocated to subcarrier , with and . Here, and denote the channel coefficient and transmitted symbol on the -th subcarrier, respectively. Accordingly, the signal contribution to the rotating-frame Hamiltonian is obtained by superposing the contributions from all subcarriers.
Based on the above discussion, the multicarrier Hamiltonian can be written as
We assume that the aggregate multicarrier microwave field is weak relative to the LO field. Under the first-order approximation, each subcarrier independently induces sideband coherences at , while the zeroth-order coherence remains unchanged and higher-order intermodulation terms are neglected. Solving the Lindblad master equation under these approximations, we obtain
Therefore, compared with the single-carrier case, the first-order atomic response is simply the superposition of the sideband responses generated by the signal components. Substituting the first-order coherence in (35) into (11), we have
Under the same first-order weak-signal approximation, the exponential term in (36) can be approximated as
After photodetection and removal of the DC component, the corresponding AC voltage is
For notational convenience, we define the frequency-dependent complex response of the RAQR as
Then, the multicarrier AC voltage can be rewritten as
(40) shows that the photodetector output is a real-valued multi-tone IF waveform, whose -th component has the complex envelope . Compared with the single-carrier case, the RAQR therefore simultaneously maps the received multicarrier RF signal onto multiple IF components with subcarrier-dependent atomic amplitude and phase responses.
In the following, we describe the FFT-based digital demodulation of . First, we place the data subcarriers below the LO, namely , and thus , . Each symbol interval is uniformly sampled at points, corresponding to a sampling rate of . The -th sample is given by
Exploiting discrete Fourier transform (DFT) orthogonality, the noisy observation on the th subcarrier is obtained through an -point FFT as
where denotes the equivalent noise after FFT demodulation. Following [19], the receiver-noise model incorporates quantum projection noise, photon shot noise, and thermal noise.
Stacking the FFT outputs across all subcarriers yields the vector model
where , , and denote the received-signal, transmitted-symbol, and noise vectors, respectively. The transmit-power allocation matrix is defined as . Furthermore, and collect the complex frequency responses and wireless channel coefficients across the subcarriers, respectively.
Remark 1 (One-sided bandwidth): Although the RAQR exhibits responses at both positive and negative microwave-LO frequency offsets, the real-valued BCOD output maps the two sidebands onto the same demodulated frequency band. Therefore, the transmitted signals on both sides would overlap and create image interference. To avoid this ambiguity, data subcarriers are allocated to only one side of the LO. For an approximately symmetric response, the resulting usable bandwidth for independent data transmission is about half of the double-sided atomic-response bandwidth.
Remark 2 (Frequency-dependent atomic response): (43) shows that the RAQR first converts the received RF multicarrier signal into a real-valued multi-tone IF waveform, which is then digitized and decomposed into orthogonal subcarriers via a single FFT. However, the FFT only separates the orthogonal subcarriers and does not compensate for either the frequency-dependent RAQR response or the wireless propagation channel. In particular, the strongly frequency-dependent atomic response may cause substantial subcarrier-dependent amplitude and phase variations, motivating the RAQR-aware frequency-domain equalizer.
RAQR-Aware Equalization
Assuming perfect knowledge of the nonzero composite subcarrier gain , the estimated symbol based on the RAQR-aware zero-forcing (ZF) equalizer is
Accordingly, the output SNR is given by
Then, the achievable rate is expressed as
Bandwidth and Conversion-Gain Analysis
This section characterizes the effects of the LO and AUX fields on the one-sided response and examines its tradeoff with bandwidth.
Response and Performance Metrics
To characterize the receiver bandwidth, we normalize the complex response by its zero-detuning value . At each fixed LO/AUX operating point, the normalized response and the corresponding LO-referenced bandwidth are defined as
Here, characterizes the center atomic-response amplitude, whereas the actual conversion coefficient satisfies . The readout prefactor is independent of but varies with the LO and AUX driving. Note that this definition imposes a lower threshold relative to the center response rather than a bound on in-band ripple. For nonmonotonic responses with off-center peaks, the bandwidth does not guarantee a ripple of at most 3 dB and generally differs from the peak-referenced 3-dB bandwidth.
Owing to the analytical intractability of , analyzing the normalized response is nontrivial. To tackle this issue, we assume that the probe, coupling, and LO fields are perfectly resonant, namely . Substituting these conditions into (2)–(4), we have , , and . Then, is simplified to for , where
The imaginary parts of these complex detunings are the decay rates of the coherences, whereas the real parts of and are the AC Stark shifts that the AUX field induces on and . Then, these complex detunings and the field couplings are collected into the coherence matrix, which is given by
Expanding along the row of , we have
Substituting into (14) and (15), the response at perfect resonance is expressed as
where . Although (52) is explicit, the roles of LO and AUX driving are not apparent. To clarify these roles, we approximate the resonance locations by exploiting two separated frequency scales. The complex detunings, comprising decay rates and AUX-induced shifts, govern the leading-order linewidths and frequency shifts, whereas the coupling and LO fields set the dominant splitting through the dressing scale
Effects of a Far-Detuned AUX Field
We first simplify the response by eliminating the coherence associated with , and obtain a frequency-dependent representation. Since couples only to , the Schur complement of its diagonal entry in yields
For , is the upper-left block of with replaced by . The factors and in the numerators are cancelled by factorization, and thus the AUX influence is retained through the frequency-dependent correction to the complex detuning of .
To approximate the AUX-induced correction as frequency-independent, we assume throughout the band of interest. Then, with , the shift of reduces to the static dispersive shift . Accordingly, is approximated by
where and
Therefore, we have , where is
Substituting this result into (52), we have
Remark 3 (Effects of AUX MW): The far-detuned AUX field influences the receiver primarily through dispersive dressing rather than resonant population transfer. The admixture of into scales as and remains small under the far-detuning assumption. Its dominant effect is to introduce static
| Atomic Driving and Relaxation | ||
| Parameter | Value | Unit |
| Probe Rabi frequency | 0.85 | MHz |
| Coupling Rabi frequency | 15 | MHz |
| LO Rabi frequency | 7.5 | MHz |
| AUX Rabi frequency | 150 | MHz |
| Probe detuning | 0 | MHz |
| Coupling detuning | 0 | MHz |
| LO detuning | 0 | MHz |
| AUX detuning | 1697 | MHz |
| Off-resonant detuning | 3214 | MHz |
| Effective dephasing rate | 0.352 | MHz |
| Decay rate | 6.07 | MHz |
| Decay rate | 2.2, 2.2, 2.2 | kHz |
| Optical and Cell Parameters | ||
| Parameter | Value | Unit |
| Probe dipole | 2.989 | |
| Coupling dipole | 0.01527 | |
| LO/signal dipole | 2117.49 | |
| AUX dipole | 2176.08 | |
| Probe wavelength | 780.241 | nm |
| Cell length | 6.5 | cm |
| Atomic density | ||
| Probe power | 252 | nW |
| Coupling power | 3 | W |
| Beam diameter | 0.7 | mm |
| Reference optical power | 30 | mW |
| PD responsivity | 0.5494 | A/W |
| Readout and Communication | ||
| Parameter | Value | Unit |
| LO carrier frequency | GHz | |
| Electrical power gain | 30 | dB |
| Load resistance | 1 | |
| Number of subcarriers | 1024 | – |
| Subcarrier spacing | 10 | kHz |
| Allocated bandwidth | 10.24 | MHz |
| Total transmit power | 23 | dBm |
| Transmit antenna gain | 0 | dBi |
| Propagation distance | 1500 | m |
| Noise temperature | 100 | K |
| RF receiver noise figure | 7 | dB |
| Effective RF receive gain | 3.951 | dBi |
level shifts. Specifically, experiences the effective shift , which combines the AC Stark shift from the off-resonant coupling and the dispersive shift induced by , while is shifted by . The five-level receiver can therefore be interpreted as an effective four-level system with tunable Rydberg-level detunings. As shown below, these shifts play distinct roles. The shift mainly controls the position of the Autler–Townes doublet, whereas primarily modifies the conversion gain.
Autler–Townes Doublet
According to (56), is the characteristic polynomial of . Therefore, the resonances of the two terms in (57) are associated with its eigenvalues and their mirror images about the LO frequency, respectively. Physically, the coupling and LO fields form three dressed states from , , and . In the lossless, zero-detuning limit, their eigenvalues are 0 and . The dark state contains no component because the two coupling pathways interfere destructively, whereas the bright states form an Autler–Townes doublet with splitting . Decay rates broaden the dressed-state resonances, whereas AUX-induced detunings shift their frequencies. When these diagonal perturbations are small relative to the dressed-state splitting, first-order perturbation theory yields eigenvalue corrections weighted by the corresponding unperturbed dressed-state populations. Accordingly, is approximated by
where denotes the approximate dark-mode eigenvalue, while and represent the frequency shift and decay rate of the bright modes, respectively.
Remark 4 (Effects of LO and AUX): Physically, increasing enlarges the doublet splitting and reduces its linewidth by decreasing the contribution of the short-lived state . In contrast, AUX driving shifts the bright-mode doublet through and perturbs the dark resonance through . With AUX driving, the dark resonance shifts to for , contributing to an asymmetric atomic response about the LO. Under the considered operating conditions, this asymmetry favors negative signal–LO offsets, motivating the allocation of data subcarriers below the LO frequency.
Impacts on Gain and Bandwidth
The dark resonance primarily determines the center atomic gain. By setting in (57), we have
Since , the EIT condition allows us to approximate . Substituting this equation into (59), is approximated by
where . Under AUX driving, the center atomic gain in (60) depends jointly on the LO Rabi frequency and the AUX-induced shift . Increasing enhances RF-induced modulation but also increases , which may suppress the center response. Meanwhile, AUX driving modifies both the numerator and denominator of (60) through . Consequently, AUX driving can enhance the center gain when its positive contribution outweighs the detuning-induced loss. Specifically, for a fixed LO operating point, the approximate gain exceeds its AUX-free value when
The bright states primarily determine the side peaks. Near , the second term of (57) dominates when . The corresponding peak magnitude is approximated by , and the peak-to-center ratio is given by
Without AUX driving, this ratio reduces to and increases with for . In contrast, AUX driving increases and reduces the side peak by the factor with a fixed LO.
Remark 5 (Effects of LO and AUX driving on the gain-bandwidth tradeoff): Increasing enlarges the dressed-state splitting and can broaden the continuous LO-referenced bandwidth by shifting the bright-mode resonances outward. However, the center atomic gain does not increase monotonically and eventually decreases in the LO-dominated regime. In contrast, AUX driving primarily adjusts the dressed-state detunings and can enhance the center gain under (61). Nevertheless, under the considered operating conditions, the increased center response and suppressed outer-band response can narrow the normalized LO-referenced bandwidth. Therefore, LO and AUX driving exhibit distinct effects on the gain-bandwidth tradeoff to balance sensitivity and bandwidth.
One-Sided LO-referenced Bandwidth and Gain–Bandwidth Tradeoff
To characterize the gain-bandwidth tradeoff analytically, we first consider the AUX-free receiver, for which (57) is simplified as
The corresponding center atomic gain is . Based on this response, we establish the following gain-bandwidth inequality.
Proposition 1 (Gain-bandwidth inequality): For the AUX-free receiver, let . The one-sided LO-referenced bandwidth satisfies
Proof: For the AUX-free response, direct expansion gives . If , the claimed bound holds directly. Otherwise, for , discarding the nonnegative second term yields . Evaluating this inequality at the half-power boundary , where , and using establishes (64).
Proposition 1 constrains the achievable bandwidth relative to the center atomic-response amplitude. For fixed and , increasing the center gain tightens the bandwidth bound. However, LO driving changes both quantities, and thus the actual tradeoff depends on the operating regime. As a result, we examine the strong-LO limit.
Corollary 1 (Strong-LO gain–bandwidth tradeoff): For the AUX-free receiver with , as with all other parameters fixed, the one-sided bandwidth satisfies
Proof: In the strong-LO limit, , giving . Meanwhile, the LO-referenced bandwidth satisfies . Combining their leading-order expressions yields (65).
Corollary 1 reveals that the center atomic-response power scales as in the AUX-free strong-LO regime. Consequently, doubling the one-sided bandwidth incurs an asymptotic power loss of approximately 18.1 dB.
With AUX driving, the dispersive shifts modify both the center response and the bright-mode resonances. Under the preceding far-detuned and dominant-response approximations, we consider operating points where the outer half-power crossing is also the first half-power crossing below the LO. Then, the LO-referenced bandwidth approximately satisfies
where . This relation reveals that AUX driving can enhance the center gain by adjusting the dark-state resonance, while the induced frequency shift modifies the band edge. Under the considered detuning conditions, improved the center gain may therefore come at the expense of a narrower continuous LO-referenced bandwidth, highlighting the gain-bandwidth tradeoff.
Simulation Results
This section evaluates the analytical model, the frequency response, and multicarrier equalization under the considered operating conditions.
Parameter Settings
We adopt the five-level scheme in [32], with , , , , and . Unlike the thermal-vapor configuration, we consider a laser-cooled atomic ensemble at µK, where residual Doppler broadening is assumed negligible, allowing
the stationary-atom approximation without Doppler averaging. Unless otherwise stated, the parameters are listed in tbl:1. Furthermore, the phase of LO is set to .
Closed-Form Expression Validation
We first validate the closed-form expressions derived under the weak-probe approximation. Figure 2 compares the real and imaginary parts of the derived steady-state response with numerical results obtained from the five-level Lindblad master equation for different probe Rabi frequencies. For the considered parameter setting, particularly MHz, the agreement in Figure 2 supports the weak-probe approximation for MHz. As the probe Rabi frequency increases, the discrepancy becomes more pronounced because population redistribution and saturation weaken the assumptions and for .

Figure 2. under various probe beams.
We further validate the first-order Floquet components and within the weak-probe and weak-signal regimes. Figure 3 compares their real and imaginary parts with numerical results obtained from the five-level Lindblad master equation over different signal–LO detunings. We observe that the closed-form and numerical results remain in close agreement over the considered detuning range, demonstrating that the derived expressions accurately capture the frequency-dependent responses of both first-order Floquet components. Together with the steady-state validation, this agreement supports the accuracy of the closed-form expressions in characterizing the wideband atomic response.

Figure 3. and under different frequency offsets between the LO and the signal.
Atomic Response
Figure 4 illustrates the magnitude and phase responses across different signal-LO detunings. These frequency-dependent variations introduce subcarrier-dependent distortions even under a frequency-flat wireless channel, supporting Remark 2 and motivating subcarrier-dependent equalization. It can be seen from the figure that the one-sided LO-referenced bandwidth reaches approximately 11 MHz. Moreover, the reduced model in (57) closely matches the full response under sufficiently far-detuned AUX driving. Furthermore, Figure 5 reveals the distinct roles of AUX-induced level shifts. The shift of primarily displaces the bright-state doublet, whereas the shift of modifies the dark-state resonance and can enhance the center conversion gain, consistent with Remark 3.

Figure 4. Magnitude and phase response of RAQR under various detunings between the LO and user’s signal.

Figure 5. Effects of AUX-induced level shifts on the atomic response. The individual-shift curves retain only one shift contribution to isolate its effect.
Gain–Bandwidth Tradeoff
Figure 6 illustrates the effects of LO and AUX driving on the conversion gain and one-sided LO-referenced bandwidth. Without AUX driving, increasing shifts the bright-state resonances outward and narrows their linewidths by reducing the contribution of the short-lived state . Meanwhile, the increased contribution to the dark state broadens the central resonance and reduces the center gain. Consequently, increases from 12.6 to 15.7 MHz at the cost of approximately 13.5 dB in center gain. In contrast, far-detuned AUX driving modifies the center and outer-band responses through dispersive level shifts. Under the considered operating conditions, the center response increases more strongly than the outer-band response in relative terms, thereby reducing the normalized response near the band edge. Consequently, the first half-power crossing shifts toward the LO, revealing that enhanced center conversion gain comes at the expense of a narrower LO-referenced bandwidth.

Figure 6. Effects of AUX and LO on response.
comes at the expense of a narrower LO-referenced bandwidth. Together, these results support Remarks 4 and 5, highlighting the distinct roles of LO and AUX driving in shaping the gain-bandwidth tradeoff.
Figure 7 illustrates the LO-referenced bandwidth versus the LO and AUX Rabi frequencies, with color indicating the center conversion gain . Increasing broadens the bandwidth at the expense of center gain, whereas increasing produces the opposite trend. The numerical bandwidth agrees with the analytical expression in (66), while the AUX-free results satisfy the upper bound established in Proposition 1. Moreover, the AUX-free operating points A and B agree well with the gain-bandwidth scaling predicted by Corollary 1. These results confirm the analyzed tradeoff and provide guidance for LO/AUX parameter selection.

Figure 7. Tradeoff between the center gain and bandwidth.
Wideband Multicarrier Receiver
Figure 8(a) reveals subcarrier-dependent amplitude and phase distortions caused by the frequency-selective atomic response, even under a frequency-flat wireless channel. Figure 8(b) further illustrates the impact of multipath fading, with joint ZF equalization restoring the transmitted symbols in the noiseless case. With the presence of receiver noise, Figure 8(c) shows that frequency-flat atomic calibration leads to rate saturation under mismatched decoding, whereas RAQR-aware equalization compensates for the frequency-dependent atomic response. As observed, at a transmit power of 23 dBm, the RAQR achieves a data rate 2.57 times that of the conventional RF benchmark, demonstrating the importance of RAQR-aware equalization and the potential of RAQRs for wideband multicarrier reception.

Figure 8. Constellations of input signal, RAQR output with equalization, and achievable-rate performance.
Conclusions
This paper investigated continuous wideband OFDM reception using a five-level RAQR with a single microwave LO. The analysis revealed that the frequency-selective atomic response introduces subcarrier-dependent amplitude and phase distortions, highlighting the importance of RAQR-aware ZF equalization. Furthermore, LO and AUX driving exhibited distinct effects on the gain-bandwidth tradeoff. Under the considered operating conditions, stronger LO driving broadened the bandwidth at the expense of center response, whereas appropriate AUX driving enhanced the center response while narrowing the contiguous passband. In the AUX-free strong-LO regime, doubling the bandwidth incurred an approximately 18-dB reduction in center-response power. Simulation results supported these findings and demonstrated a contiguous one-sided LO-referenced bandwidth exceeding 11 MHz. These insights provide guidance for balancing bandwidth and conversion gain, highlighting the potential of RAQRs as wideband receiving front ends for future wireless communications.
Appendix A: Proof of the Weak-Probe Closed-Form Optical Coherence
Substituting the Hamiltonian in (1) into the master equation (9), we obtain the evolution equations for the coherences , . Defining , these equations are given by
These equations are obtained without invoking the weak-probe approximation. Since the repopulation matrix is diagonal, it does not contribute to the off-diagonal coherence dynamics, while the anticommutator term determines the coherence decay rates.
Under the weak-probe approximation, the atomic population remains predominantly in the ground state, yielding and , . Meanwhile, coherences between excited states are neglected, i.e., , . Consequently, , and (67) reduces to a closed set of linear equations for , , , and , while retaining the coupling, LO, and AUX fields without assuming weak driving.
Then, with the weak-signal, i.e., , the coherences are expanded as
where the terms of higher order are neglected. Substituting the Floquet expansions into (67) and retaining terms up to first order in yields three linear systems with the same coefficient structure. Therefore, these systems can be
expressed in a unified matrix form as
where , , and . The coherence vector is defined as
The coefficient matrix is given by
where and , . The corresponding source vectors are
The signal phase is already incorporated into the Floquet harmonics.
Since the three Floquet components share the same matrix structure, their solutions can be obtained through a common elimination procedure. For a fixed , let , , and write . The subscripts follow the atomic-state indices. In the following elimination, the superscript is omitted and all response functions are evaluated at . Specifically, eliminating the third and fourth entries of , we have
where
and
Substituting into (73), we obtain
Similarly, substituting and into (73) and using (76), we have
Therefore, we complete the proof.
References
References
- [1]C.-X. Wang, X. You, X. Gao, X. Zhu, Z. Li, C. Zhang, H. Wang, Y. Huang, Y. Chen, H. Haas et al., “On the road to 6G: Visions, requirements, key technologies, and testbeds,” IEEE Commun. Surv. Tutor., vol. 25, no. 2, pp. 905–974, 2023.arxiv.org/abs/2302.14536
- [2]Q. Peng, Q. Luo, D. Xia, Z. Zhang, J. Wu, K. Wang, C. Pan, M. Elkashlan, P. Xiao, D. W. K. Ng, T. Q. Duong, G. K. Karagiannidis, and J. Wang, “Beyond the RF paradigm: Rydberg atomic receivers for next-generation IoT,” 2026, arXiv:2606.01263. [Online]. Available: https://arxiv.org/abs/2606.01263
- [3]H. Lu, Y. Zeng, C. You, Y. Han, J. Zhang, Z. Wang, Z. Dong, S. Jin, C.-X. Wang, T. Jiang, X. You, and R. Zhang, “A tutorial on near-field XL-MIMO communications toward 6G,” IEEE Commun. Surv. Tutor., vol. 26, no. 4, pp. 2213–2257, 2024.DOI
- [4]H. Tataria, M. Shafi, A. F. Molisch, M. Dohler, H. Sjöland, and F. Tufvesson, “6G wireless systems: Vision, requirements, challenges, insights, and opportunities,” Proc. IEEE, vol. 109, no. 7, pp. 1166–1199, 2021.
- [5]F. Lin, P.-I. Mak, and R. P. Martins, “Wideband receivers: Design challenges, tradeoffs and state-of-the-art,” IEEE Circuits Syst. Mag., vol. 15, no. 1, pp. 12–24, 2015.DOI
- [6]P. K. Sharma and N. Nallam, “Breaking the performance tradeoffs in N-path mixer-first receivers using a second-order baseband noise-canceling TIA,” IEEE J. Solid-State Circuits, vol. 55, no. 11, pp. 3009–3023, 2020.DOI
- [7]T. Gong, A. Chandra, C. Yuen, Y. L. Guan, R. Dumke, C. M. S. See, M. Debbah, and L. Hanzo, “Rydberg atomic quantum receivers for classical wireless communication and sensing,” IEEE Wireless Commun., vol. 32, no. 5, pp. 90–100, 2025.DOI
- [8]J. A. Sedlacek, A. Schwettmann, H. Kübler, R. Löw, T. Pfau, and J. P. Shaffer, “Microwave electrometry with Rydberg atoms in a vapour cell using bright atomic resonances,” Nat. Phys., vol. 8, no. 11, pp. 819–824, 2012.DOI
- [9]A. Mohapatra, T. Jackson, and C. Adams, “Coherent optical detection of highly excited rydberg states using electromagnetically induced transparency,” Phys. Rev. Lett., vol. 98, no. 11, p. 113003, 2007.pubmed.ncbi.nlm.nih.gov/17501049
- [10]E. Saglamyurek, T. Hrushevskyj, A. Rastogi, K. Heshami, and L. J. LeBlanc, “Coherent storage and manipulation of broadband photons via dynamically controlled autler–townes splitting,” Nat. Photonics, vol. 12, no. 12, pp. 774–782, 2018.DOI
- [11]M. Jing, Y. Hu, J. Ma, H. Zhang, L. Zhang, L. Xiao, and S. Jia, “Atomic superheterodyne receiver based on microwave-dressed Rydberg spectroscopy,” Nat. Phys., vol. 16, no. 9, pp. 911–915, 2020.
- [12]D. H. Meyer, K. C. Cox, F. K. Fatemi, and P. D. Kunz, “Digital communication with rydberg atoms and amplitude-modulated microwave fields,” Appl. Phys. Lett., vol. 112, no. 21, 2018.DOI
- [13]D. A. Anderson, R. E. Sapiro, and G. Raithel, “An atomic receiver for am and fm radio communication,” IEEE Trans. Antennas Propag., vol. 69, no. 5, pp. 2455–2462, 2020.DOI
- [14]C. L. Holloway, M. T. Simons, J. A. Gordon, and D. Novotny, “Detecting and receiving phase-modulated signals with a Rydberg atom-based receiver,” IEEE Antennas Wirel. Propag. Lett., vol. 18, no. 9, pp. 1853–1857, 2019.DOI
- [15]J. Nowosielski, M. Jastrzębski, P. Halavach, K. Łukanowski, M. Jarzyna, M. Mazelanik, W. Wasilewski, and M. Parniak, “Warm Rydberg atom-based quadrature amplitude-modulated receiver,” Opt. Express, vol. 32, no. 17, pp. 30 027–30 039, 2024.DOI
- [16]Y. Cai, S. Shi, Y. Zhou, Y. Li, J. Yu, W. Li, and L. Li, “High-sensitivity Rydberg-atom-based phase-modulation receiver for frequency-division-multiplexing communication,” Phys. Rev. Appl., vol. 19, no. 4, p. 044079, 2023.DOI
- [17]S. Borówka, M. Mazelanik, W. Wasilewski, and M. Parniak, “Optically-biased Rydberg microwave receiver enabled by hybrid nonlinear interferometry,” Nat. Commun., vol. 16, no. 1, p. 8975, 2025.DOI
- [18]J.-D. Nan, J.-R. Chen, B. Liu, Q.-F. Wang, Y. Ma, Y.-M. Yin, T.-Y. Han, G.-C. Guo, H. Tian, L.-H. Zhang, B. Du, B.-B. Wei, D.-S. Ding, and B.-S. Shi, “Ultra-broadband anti-jamming communication via a Rydberg atomic receiver,” Nat. Commun., vol. 17, p. 9643, 2026.
- [19]T. Gong, J. Sun, C. Yuen, G. Hu, Y. Zhao, Y. Guan, C. M. S. See, M. Debbah, and L. Hanzo, “Rydberg atomic quantum receivers for classical wireless communications and sensing: Their models and performance,” IEEE Trans. Commun., vol. 74, pp. 7759–7778, 2026.arxiv.org/abs/2412.05554
- [20]Y. Chen, X. Guo, C. Yuen, Y. L. Guan, C. M. S. See, M. Debbah, and L. Hanzo, “Harnessing Rydberg atomic receivers: From quantum physics to wireless communications,” IEEE Trans. Wireless Commun., vol. 25, pp. 19 971–19 990, 2026.arxiv.org/abs/2501.11842
- [21]Q. Peng, Q. Luo, Z. Chu, N. Ye, H. Ren, C. Pan, L. Xiao, and P. Xiao, “From active to battery-free: Rydberg atomic quantum receivers for self-sustained SWIPT-MIMO networks,” IEEE J. Sel. Areas Commun., vol. 44, pp. 4861–4875, 2026.arxiv.org/abs/2510.15784
- [22]Q. Peng, T. Gong, Z. Song, Q. Luo, Z. Lin, P. Xiao, and C. Yuen, “Enhanced ground–satellite direct access via onboard Rydberg atomic quantum receivers,” IEEE Wireless Commun., vol. 33, no. 3, pp. 23–30, 2026.arxiv.org/abs/2510.17290
- [23]N. Schlossberger, N. Prajapati, A. B. Artusio-Glimpse, S. Berweger, and C. L. Holloway, “Fundamental linewidth limit of electromagnetically induced transparency in a thermal Rydberg ladder,” Phys. Rev. Res., vol. 8, no. 3, p. L032046, 2026.DOI
- [24]S. M. Bohaichuk, D. Booth, K. Nickerson, H. Tai, and J. P. Shaffer, “Origins of Rydberg-atom electrometer transient response and its impact on radio-frequency pulse sensing,” Appl. Phys. Lett., vol. 18, no. 3, p. 034030, 2022.
- [25]J. Hu, Y. Jiao, Y. He, H. Zhang, L. Zhang, J. Zhao, and S. Jia, “Improvement of response bandwidth and sensitivity of rydberg receiver using multi-channel excitations,” EPJ Quantum Technol., vol. 10, no. 1, p. 51, 2023.DOI
- [26]S. Berweger, N. Prajapati, A. B. Artusio-Glimpse, A. P. Rotunno, R. Brown, C. L. Holloway, M. T. Sims, E. Imhof, S. R. Jefferts, B. N. Kayim et al., “Rydberg-state engineering: Investigations of tuning schemes for continuous frequency sensing,” Phys. Rev. Appl., vol. 19, no. 4, p. 044049, 2023.DOI
- [27]D. H. Meyer, J. C. Hill, P. D. Kunz, and K. C. Cox, “Simultaneous multiband demodulation using a Rydberg atomic sensor,” Phys. Rev. Appl., vol. 19, no. 1, p. 014025, 2023.DOI
- [28]M. Cui, Q. Zeng, M. Chen, Z. Wang, T. Mao, D. Zheng, and K. Huang, “Rydberg atomic receivers for multi-band communications and sensing,” IEEE Trans. Wireless Commun., vol. 25, pp. 13 384–13 400, 2026.arxiv.org/abs/2505.24168
- [29]H. Wang, T. Gong, E. Björnsen, and C. Yuen, “Multi-carrier Rydberg atomic quantum receivers with enhanced bandwidth feature for communication and sensing,” IEEE J. Sel. Areas Commun., vol. 44, pp. 5635–5650, 2026.arxiv.org/abs/2510.10473
- [30]B. Yang, Y. Yan, X. Li, L. Xiao, X. Li, L. Chen, J. Deng, and H. Cheng, “Highly sensitive microwave electrometry with enhanced instantaneous bandwidth,” Phys. Rev. Appl., vol. 21, no. 3, p. L031003, 2024.DOI
- [31]Y. Chen, C. Yuen, and C. M. S. See, “Wideband quantum transduction for Rydberg atomic receivers using six-wave mixing,” IEEE J. Sel. Areas Commun., vol. 44, pp. 5472–5488, 2026.
- [32]Y. Yan, X. Li, J. Wan, X. Xia, H. Zhao, B. Yu, J. Deng, H. Cheng, and L. Q. Chen, “Broadband Rydberg atomic microwave sensing with 44.6 MHz instantaneous bandwidth,” 2026. [Online]. Available: https://arxiv.org/abs/2606.25555
- [33]H. Zhu and J. Wang, “Chunk-based resource allocation in OFDMA systems-part I: chunk allocation,” IEEE Trans. Commun., vol. 57, no. 9, pp. 2734–2744, 2009.DOI
- [34]H. Zhu and J. Wang, “Chunk-based resource allocation in OFDMA systems—part II: Joint chunk, power and bit allocation,” IEEE Trans. Commun., vol. 60, no. 2, pp. 499–509, 2011.DOI